MODEL 351 POWERGLIDE SERIES INSTRUCTIONS

MODEL 351 POWERGLIDE SERIES
INSTRUCTIONS FOR INSTALLING SARGENT DOOR
CLOSERS WITH REGULAR ARMS (WITHOUT HOLDER)
351 SERIES NON SIZED ADJUSTABLE SIZES 1 THRU 6
CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE.
FOR ASSISTANCE, CALL SARGENT AT 1-800-727-5477.
1
STANDARD & TOP JAMB APPLICATIONS
STANDARD APPLICATION
(TYPE 25-O ARM)
DOOR WIDTH
(INCHES)
24
30
32
36
40
42
44
46
48
OVER 48
USE
PAGE 2
CLOSER MOUNTED ON
HINGE SIDE OF DOOR
NUMBER OF TURNS OF SPRING POWER ADJUSTING SCREW
FROM FACTORY SETTING (USE CHART AS GUIDE ONLY)
APPROXIMATE
351
INTERIOR DOORS
DOOR WEIGHT (POUNDS)
EXTERIOR DOORS
80
FACTORY SET
110
1-4 CW
115
1-5 CCW
130
4-7 CW
150
155
7-10 CW
FACTORY SET
165
170
1-5 CW
10-12 CW
180
UP TO 18 CW AS REQ. 5 CW AND UP AS REQ.
ADJUST SPRING POWER ACCORDING TO CHART*
NOTE: FOR 08 AND OLC TYPE ARMS MOUNTING
SEE DATA SHEETS ENCLOSED
+
TOP JAMB
APPLICATION
(TYPE 25-O, 25-OZ
AND 25-OZA ARMS)
-
INCREASE
POWER
DECREASE
POWER
CLOCKWISE
(CW)
COUNTER CLOCKWISE
(CCW)
5/8" SPRING POWER
ADJUSTMENT NUT
USE
PAGE 3
LEFT
HAND DOOR
PULL
HINGE SIDE
STOP (PUSH) SIDE
CLOSER MOUNTED ON FRAME
ON STOP SIDE OF DOOR
PULL
HINGE SIDE
RIGHT
HAND DOOR
STOP (PUSH) SIDE
PARALLEL APPLICATION ONLY
PARALLEL ARM
APPLICATION
(TYPE 25-P9)
CLOSER MOUNTED ON
STOP SIDE OF DOOR
USE
PAGE 4
DOOR WIDTH
(INCHES)
24
30
32
36
40
42
44
46
48
OVER 48
NUMBER OF TURNS OF SPRING POWER ADJUSTING NUT
FROM FACTORY SETTING (USE CHART AS GUIDE ONLY)
INTERIOR DOORS
APPROXIMATE
351
DOOR WEIGHT (POUNDS)
EXTERIOR DOORS
80
2-6 CW
110
115
6-8 CW
1-5 CCW
130
150
FACTORY SET
8-11 CW
155
165
170
11-13 CW
1-7 CW
180
UP TO 18 CW AS REQ. 8 CW AND UP AS REQ.
ADJUST SPRING POWER ACCORDING TO CHART*
*IF INTERIOR DOORS DO NOT HAVE TO COMPLY WITH ADA REQUIREMENTS, EXTERIOR DOOR SETTINGS
ARE RECOMMENDED. WHERE STRONG DRAFTS EXIST, INCREASE SPRING POWER AS NEEDED BY TURNING
SPRING ADJUSTMENT SCREW CLOCKWISE. IF NECESSARY, REDUCE SPRING POWER BY TURNING SCREW
COUNTERCLOCKWISE.
Copyright © 2003, 2008, 2011 Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7340C
1
351 STANDARD ARM APPLICATION INSTRUCTIONS
IMPORTANT: USE ALTERNATE MOUNTING IF DOOR CAN
OPEN BEYOND LIMITS SHOWN FOR STANDARD MOUNTING
ARM
TYPE
REGULAR
ARM NO
HOLDER
MOUNTING
MAX. DOOR
OPENING
DIM.
A
DIM.
B
STANDARD
120∞
8 3/16"
11 7/16"
ALTERNATE
160∞
6 13/16"
10 1/16"
IF BUTT, FRAME AND WALL CONDITIONS PERMIT DOOR WILL
OPEN 180°
1
2
#12 x 3 WOOD SCREWS OR
#12-24 X 2 1/4 FLAT HEAD
MACHINE SCREWS
DIM. "B"
SEE PAGE 6 FOR MORTISE NUTS
DIM. "A"
TOP OF DOOR
RIGHT HAND DOOR SHOWN. LEFT HAND
DOOR OPPOSITE.
THIS DIMENSION IS TAKEN FROM HINGE
EDGE OF DOOR FOR INVISIBLE HINGES.
9/16"
2 1/2"
9"
DRILL & TAP AND USE SCREWS PROVIDED OR USE MORTISE
NUTS WHEN REQUIRED.
USE TEMPLATE A6753 FOR 25-OLC ARM
(LOW PROFILE)
A
1 1/8"
2"
CL OF HINGE PIVOT: BUTTS, OFFSET PIVOTS,
SWING CLEAR, CENTER HUNG OR INVISIBLE HINGES
INSTALL DOOR CLOSER TO DOOR WITH
SPRING ADJUSTMENT NUT AWAY FROM HINGE.
NOTE: 351 CLOSER BODIES ARE NON HANDED.
IT IS IMPORTANT THAT THE CLOSER BODY BE
MARKED WITH “RH” SYMBOL AT TOP, FOR RIGHT
HAND DOORS. “LH” SYMBOL AT TOP FOR LEFT
HAND DOORS.
RH
RIGHT HAND
DOOR SHOWN
ATTACH FOOT TO FRAME WITH PIVOT
AWAY FROM HINGE.
C
ATTACH ARM WITH INDEX MARK ON SPINDLE ALIGNED AS SHOWN. SECURE WITH SCREW AND
WASHER. INSERT ROD END INTO SWIVEL ARM AND TIGHTEN ARM SCREW AS SHOWN BELOW.
RIGHT HAND DOOR SHOWN (LEFT HAND DOOR OPPOSITE)
5
4
PIVOT
90°
MAIN ARM
1
ARM
SCREW
3
ROD
2
B
INDEX MARK
ON SPINDLE
POSITION OF
MAIN ARM WHEN
ASSEMBLING
TO SPINDLE
SWIVEL ARM
Copyright © 2003, 2008, 2011 Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7340C
2
351 TOP JAMB APPLICATION INSTRUCTIONS
ARM
TYPE
REVEAL
DEPTH
“O” ARM
0" TO 2"
“OZ” ARM
“OZA” ARM
DOOR
OPENING
DIM.
A
MAX.
DOOR OPENING
140°
8 5/8"
110°
2 1/8" TO 5"
140°
5 3/8"
140°
5 1/8" TO 8"
140°
1
RIGHT HAND DOOR SHOWN,
LEFT HAND DOOR OPPOSITE.
2
THIS DIMENSION IS TAKEN FROM HINGE
EDGE OF DOOR FOR INVISIBLE HINGES.
3
DOOR OPENING TO 180∞ IS POSSIBLE IF
DEPTH OF REVEAL IS NOT GREATER THAN 2"
DRILL & TAP AND USE SCREWS PROVIDED OR USE MORTISE NUTS WHEN REQUIRED.
5/8"
STOP
MAX
9"
1 1/2"
3 1/4"
PROVIDE 5/16" DIAMETER CLEARANCE
HOLES IN FRAME FOR CLOSER SCREWS
WHICH PROJECT 5/16" BEYOND PLATE
6"
1"
351-A PLATE
2 1/4"
A
2"
SEE PAGE 6 FOR
MORTISE NUTS
2 1/2"
STOP
DEPTH OF REVEAL
13/16"
DOOR
351-A MOUNTING
PLATE
DOUBLE RABBETED
FRAME WITH REQUIRED
MOUNTING PLATE
#12 X 1 1/2"
WOOD SCREWS OR
#12-24 X 5/8"
FLAT HEAD
MACHINE SCREW
1 3/4" MIN
1"
7/16"
DEPTH OF REVEAL
NOTE: 351 CLOSER BODIES ARE NON HANDED.
IT IS IMPORTANT THAT THE CLOSER BODY BE
MARKED WITH “RH” SYMBOL AT TOP, FOR LEFT
HAND DOORS. “LH” SYMBOL AT TOP FOR RIGHT
HAND DOORS.
INSTALL DOOR CLOSER TO FRAME WITH SPRING
ADJUSTMENT NUT AWAY FROM HINGE.
3 1/2"
1"
TOP OF DOOR
1"
3 1/4"
CL OF PIVOT HINGE
FRAME
FRAME
1/4"
7/16"
DIM A
SINGLE
RABBETED
FRAME
B
ATTACH FOOT TO DOOR WITH
PIVOT AWAY FROM HINGE.
RIGHT HAND
DOOR SHOWN
LH
HINGE
SIDE
INSTALL MAIN ARM TO SPINDLE AND SECURE WITH SCREW AND WASHER AS SHOWN. OPEN DOOR INSERT RETANGULAR ROD INTO SWIVEL
ARM THEN CLOSE THE DOOR AND TIGHTEN ARM SCREW SECURELY WHEN SWIVEL ARM IS AT RIGHT ANGLE TO DOOR.
FOOT PIVOT
FOOT PIVOT
RIGHT HAND DOOR
LEFT HAND DOOR
MAIN
ARM
ROD
ARM
SCREW
90°
ROD
1
5
SWIVEL ARM
2
3
POSITION OF
MAIN ARM WHEN
ASSEMBLING
TO SPINDLE
INDEX
MARK
ON
SPINDLE
90°
ARM
SCREW
4
C
VIEW LOOKING UP
WHEN ASSEMBLING
ARM TO SPINDLE
POSITION OF
MAIN ARM WHEN
ASSEMBLING
TO SPINDLE
SWIVEL ARM
Copyright © 2003, 2008, 2011 Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7340C
3
351 parallel arm APPLICATION INSTRUCTIONS
CL OF HINGE PIVOT
(BUTT HINGE SHOWN)
MAX. DOOR
OPENING
DIM.
A
DIM.
B
120°
9 7/8"
10 1/4"
180°
7"
7 3/8"
5/16"
DOOR
#12 WOOD SCREWS
OR #12-24 x 5/8 FLAT HEAD
MACHINE SCREWS
1/2"
7/8"
TOP VIEW
DIM. B
LEFT HAND DOOR SHOWN. RIGHT HAND
DOOR DIMENSION OPPOSITE.
1
2 1/2"
1 1/4"
DIM. A
2
DO NOT USE THIS MOUNTING FOR
“SWING CLEAR” HINGES.
3
THIS DIMENSION IS TAKEN FROM HINGE
EDGE OF DOOR FOR INVISIBLE HINGES.
2 3/8"
STOP
2 1/2"
DRILL & TAP AND USE SCREWS PROVIDED OR USE
MORTISE NUTS WHEN REQUIRED.
#12 X 3" WOOD SCREWS
OR #12-24 X 2 1/4"
MACHINE SCREW
9"
SEE PAGE 6 FOR
MORTISE NUTS
CL OF HINGE PIVOT
A
TOP OF
DOOR
B
INSTALL DOOR CLOSER TO DOOR WITH SPRING ADJUSTMENT
NUT AWAY FROM HINGE.
ATTACH FOOT BRACKET TO FRAME STOP.
RIGHT HAND
DOOR SHOWN
RH
NOTE: 351 CLOSER BODIES ARE NON HANDED.
IT IS IMPORTANT THAT THE CLOSER BODY BE
MARKED WITH “RH” SYMBOL AT TOP, FOR RIGHT
HAND DOORS. “LH” SYMBOL AT TOP FOR LEFT HAND DOORS.
C
USING WRENCH ON BOTTOM END OF SPINDLE, ROTATE SPINDLE 45∞ AND ASSEMBLE
MAIN ARM TO CLOSER AS SHOWN, AND THEN INSERT ROD END INTO SWIVEL ARM AND
TIGHTEN ARM SCREW POSITIONING ARM 1 1/2" AWAY FROM DOOR.
RIGHT HAND VIEW OF INDEX
LEFT HAND VIEW OF INDEX
INDEX MARK
ON SPINDLE
3
1
4
1 2
2
PRELOAD
APPROX. 50°
3
5
45°
5
INDEX MARK
ON SPINDLE
45°
OPTIONAL ARMS FOR MOUNTING. SEE DATA
SHEET ENCLOSED.
P4 OR P4A
BRACKET
P3 OR P3A
BRACKET
MAIN
ARM
POSITION OF MAIN ARM
WHEN ASSEMBLINGTO SPINDLE
4
MAIN ARM
CAUTION: DOOR CLOSER
WILL NOT OPERATE
PROPERLY IF ARM IS NOT
INDEXED CORRECTLY.
(SARGENT
#590 SHOWN)
1 1/2"
RIGHT HAND
DOOR
ROD
MAIN ARM
ARM SCREW
FOR FLUSH FRAME
AND DOOR CONDITIONS
FOR USE WITH
OVERHEAD
DOOR HOLDERS
P4A BRACKET IS USED
WITH OVERHEAD HOLDERS
FOOT BRACKET
Copyright © 2003, 2008, 2011 Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7340C
4
FINAL ADJUSTMENT AND REGULATING PROCEDURE
BACKCHECK
VALVE
OPTIONAL DELAYED
ACTION VALVE
DELAYED ACTION
RANGE
CLOSING SPEED
RANGE
DOOR SPEED
VALVE
BACKCHECK
RANGE
LATCHING
SPEED VALVE
REGULATING DOOR SPEED AND LATCHING SPEED AS NEEDED.
B
USE HEX SOCKET (1/8" ALLEN) WRENCH AND TURN VALVES
CLOCKWISE TO SLOW DOWN OR COUNTER CLOCKWISE TO
SPEED UP DOOR MOVEMENT.
FASTER
(+)
C
“DELAYED ACTION” PROVIDES SLOW DOOR CLOSING THROUGH
DELAYED ACTION RANGE
TURN VALVE CLOCKWISE TO SLOW DOWN OR COUNTER
CLOCKWISE TO SPEED UP DOOR MOVEMENT
E
TO REGULATE THE INTENSITY OF BACKCHECK ACTION TURN VALVE
CLOCKWISE TO INCREASE OR COUNTER CLOCKWISE TO DECREASE
CHECKING.
CAUTION: SET VALVE FOR SLIGHT CUSHIONING EFFECT. IT IS
DAMAGING TO THE CLOSER IF THE CHECKING ACTION IS TOO ABRUPT.
NEVER USE BACKCHECK AS A DOOR STOP.
ALWAYS USE A DOOR STOP TO STOP THE DOOR.
SLOWER
(–)
FOR MODELS WITH OPTIONAL DELAYED ACTION FEATURE
REGULATING BACKCHECK
D
ADJUSTING FOOT FOR ADDITIONAL CLOSING POWER
(FOR STANDARD AND TOP JAMB APPLICATIONS ONLY)
MOVE FOOT
PIVOT TO HOLE
NEAREST HINGE
+
+
HINGE EDGE OF DOOR
A
LATCHING
SPEED RANGE
INSTALL COVER WITH TWO SCREWS AS SHOWN.
INSERT IS REMOVABLE.
PLACE IN UNUSED OPENING.
Copyright © 2003, 2008, 2011 Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7340C
5
USING MORTISE NUTS WITH SARGENT DOOR CLOSER
1. SEE INSTRUCTIONS OR DATA SHEET PACKED WITH DOOR CLOSER FOR DIMENSIONS LOCATING
THE CLOSER BODY AND FOOT ON DOOR AND FRAME.
2. MORTISE NUT SHOWN IS DESIGNED FOR AN UNREINFORCED METAL DOOR.
3. FOR TOP JAMB AND CORNER BRACKET APPLICATIONS: THE DOOR CLOSER FOOT WILL BE ATTACHED TO THE DOOR IN A MANNER SIMILAR TO THAT
SHOWN FOR MOUNTING THE CLOSER BODY.
4. FOR DOORS 2 1/4" THICK: MORTISE NUT SHOWN FOR 1 3/4" THICK DOORS WILL BE FURNISHED ALONG WITH APPORPRIATE LENGTH THRU-BOLTS.
DOOR CONSTRUCTION MUST PROVIDE A BRIDGE TYPE REINFORCEMENT TO PREVENT THE DOOR RAIL FROM COLLAPSING WHEN THRU-BOLTS
ARE TIGHTENED.
SARGENT 1430
SERIES CLOSER
SHOWN. (OTHER
SERIES SIMILAR)
SEE NOTE #1 BELOW FOR DIMENSION
INFORMATION. IF A DIMENSION LESS THAN
7/8" IS USED. THE DOOR STOP MUST BE CUT
TO CLEAR THE MORTISE NUT HEAD OR THE
MORTISE NUT HEAD MUST BE RECESSED.
(SEE ENLARGED VIEW "Y")
FRAME
DOOR STOP
COVER
MORTISE NUT HEAD
DOOR
DRILL 3/8" DIA.
HOLE FOR MORTISE
NUT BODY.
DRILL 1/4" DIA. HOLE
FOR MOUNTING SCREWS
SARGENT 351 SERIES SHOWN
1/8"
SHORTEN MORTISE
NUT BODY TO
THIS LENGTH
5/8" DIA. HOLE
FRAME
DOOR
STOP
DOOR CLOSER SHOWN
(TRACK ASSEMBLY
MOUNTING IS SIMILAR)
#12-24 THREAD
MORTISE NUT
9/16"
DIA.
DOOR
1/4" DIA.
DRILLED HOLE
VIEW "Y"
MORTISE NUT
HEAD
3/8" DIA. HOLE
7/64"
1 11/16" FOR 1 3/4" THICK DOOR
1 5/16" FOR 1 3/8" THICK DOOR
(SEE NOTE #4 FOR 2 1/4" THICK DOORS)
Copyright © 2003, 2008, 2011 Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
A7340C
6