HDMI Detective Plus

®
HDMI Detective
Plus
EXT-HDMI-EDIDP
User Manual
www.gefen.com
ASKING FOR ASSISTANCE
Technical Support:
Telephone
(818) 772-9100
(800) 545-6900
Fax(818) 772-9120
Technical Support Hours:
8:00 AM to 5:00 PM Monday through Friday, Pacific Time
Write To:
Gefen LLC
c/o Customer Service
20600 Nordhoff St
Chatsworth, CA 91311
www.gefen.com
support@gefen.com
Notice
Gefen LLC reserves the right to make changes in the hardware, packaging, and
any accompanying documentation without prior written notice.
HDMI Detective Plus is a trademark of Gefen LLC
© 2011 Gefen, LLC. All rights reserved.
All trademarks are the property of their respective owners.
Rev A10
CONTENTS
1Introduction
2
Operation Notes
3Features
4
Panel Layout
5
Panel Descriptions
6
Connecting the HDMI Detective Plus
7
8
Wiring Diagram
EDID Programming
8
Using a built-in EDID
9
Writing an EDID using a source device
10 Specifications
11Warranty
INTRODUCTION
Congratulations on your purchase of the HDMI Detective Plus. Your complete
satisfaction is very important to us.
Gefen
Gefen delivers innovative, progressive computer and electronics add-on solutions
that harness integration, extension, distribution and conversion technologies.
Gefen’s reliable, plug-and-play products supplement cross-platform computer
systems, professional audio/video environments and HDTV systems of all sizes
with hard-working solutions that are easy to implement and simple to operate.
The Gefen HDMI Detective Plus
Computers and HDTV video source devices can sometimes lose the EDID -(which is basically the electronic identification of a display) which lists its possible
resolutions and frequencies. When displays are switched away or disconnected
and then reconnected, the EDID can be lost and the computer or HD video
source device can lose the ability to display the image properly. The HDMI
Detective Plus product allows you to switch or relocate HDTV or Computer video
displays while “tricking” the source devices into thinking that the display is still
present -- maintaining smooth video operations throughout the process.
How It Works
The Gefen HDMI Detective Plus attaches to the HDTV display’s HDMI input
connector for initial programming. Power is applied and the HDMI Detective Plus
reads and stores the attached displays EDID to the internal memory. Then the
HDMI Detective Plus is attached to your source HDMI output and it will never
lose EDID again.
The HDMI Detective Plus includes 4 built-in selectable generic EDIDs that can be
used for meeting standard home theater setups. They can be selected by moving
the dip switches between the different settings.
1
OPERATION NOTES
THIS PAGE LEFT INTENTIONALLY BLANK
2
FEATURES
Features
•
Quick and easy recording of EDID information from HDTV displays
•
Write custom EDID information using an external source
(e.g. signal generator, etc)
•
Selection of preset EDIDs
•
Maintains 1920 x 1200, 1080p Full HD, and 2k resolution video
•
No power required after initial programming
•
HDCP Compliant
•
Compact unit hides well behind equipment
Package Includes
(1) HDMI Detective Plus
(1) 1 ft. HDMI cable (M-M)
(1) 5V DC power supply
(1) Quick Start Guide
3
PANEL LAYOUT
Front
2
1
Back
3
4
4
5
PANEL DESCRIPTIONS
1
Programming Button
Press and hold this button to program an EDID. See page 8 for more
information on recording an EDID.
2
HDMI In
Connect the included HDMI cable from this HDMI port to the source device.
3
DIP Switches
Use these DIP switches to use one of the pre-programmed EDIDs.
4
HDMI Out
Connect an HDMI cable from this HDMI port to the display (or other sink
device).
5
WR
Enables / disables the EDID write status. Set the WR switch to the “E” position
to allow the HDMI Detective Plus to be programmed with an EDID. Set the WR
switch to the “D” position to disable programming and prevent an accidental
erasure.
5
CONNECTING THE HDMI DETECTIVE PLUS
How to Connect the HDMI Detective Plus
1. Power-on the display (or other sink device) containing the EDID to be
recorded.
2. Use an HDMI cable to connect the sink device to the HDMI Out port on the
HDMI Detective Plus.
3. Set all four DIP switches in the OFF (up) position, as shown in the illustration
below.
4. Set the WR (Write) switch to the “E” (enable) position to allow the HDMI
Detective Plus to be programmed.
5. Connect the included 5V DC power supply to the HDMI Detective Plus. The
power LED will glow bright green if the sink device contains a valid EDID.
If the sink’s EDID is corrupt or invalid, then the power LED will glow bright
red.
6. Press and hold the Program button on the front panel of the HDMI Detective
Plus until the power indicator begins to rapidly flash bright green, then
release the Program button. The power LED will continue to flash as the
EDID is written to the HDMI Detective Plus.
A successful recording will be indicated with a solid green LED. If the
recording process was unsuccessful, the LED will glow bright red.
6
CONNECTING THE HDMI DETECTIVE PLUS
NOTE: If the HDMI Detective Plus does not initiate the recording
sequence, indicated by a flashing green LED, unplug the display
and 5V DC power supply from the unit and repeat steps 2 and 3.
If a solid red LED is indicated after several unsuccessful recording
attempts, it is possible that the EDID from the display is bad. In this
case, see page 8 for instructions on using a built-in EDID.
6. Remove the 5V DC power supply from the HDMI Detective Plus.
7. Set the write-protect switch to the “D” position (enable) in order to prevent an
accidental erasure of the stored EDID.
8. Use the included HDMI cable to connect the source to the HDMI Detective
Plus.
IMPORTANT: If the source uses HDCP, then DIP switch 4 must be
enabled in order to enable HDCP pass-through. In this case, the
display must also be HDCP-compliant. Refer to your source and
display manuals for HDCP compatibility.
9. Apply power to the source.
If a computer is being used as the source, restart the computer only after all
connections have been made.
Wiring Diagram for the HDMI Detective Plus
HDMI CABLE
Hi-Def Source
HDMI Detective Plus
Monitor
EXT-HDMI-EDIDP
7
OPERATING THE HDMI DETECTIVE PLUS
Using a built-in EDID
The HDMI Detective Plus includes five built-in EDIDs for use with several
standard home theater setups with multi-channel audio and standard HD
resolutions. Asterisks (“*”) indicate native resolutions.
1. Make sure that the WR (write) switch on the HDMI Detective Plus is in the
“E” position and that all DIP switches are in the OFF (down) position.
2. Select the desired EDID from the Resolutions column.
3. Set DIP switches 1 - 3 on the HDMI Detective Plus using the DIP Switches
column. DIP switch 4 is not used when programming an EDID.
4. Press and hold the Program button on the front panel of the HDMI Detective
Plus until the power indicator begins to rapidly flash bright green, then
release the Program button.
EDID
Resolutions
Refresh Rate
Audio
1
720 x 576p 4:3
720 x 576p 16:9
1280 x 720p 16:9
1920 x 1080p 16:9
*1920 x 1080i 16:9
50 Hz
8 CH PCM
DIP Switches
1
ON
2
3
OFF OFF
2
720 x 576p 4:3
1440 x 480i 16:9
1280 x 720p 16:9
1920 x 1080p 16:9
*1920 x 1080i 16:9
59.94 / 60 Hz 8 CH PCM OFF ON
3
720 x 576p 4:3
720 x 576p 16:9
1280 x 720p 16:9
1920 x 1080p 16:9
*1920 x 1080i 16:9
4
720 x 480 16:9
720 x 576p 16:9
1280 x 720p 16:9
1920 x 1080p 16:9
*1920 x 1080i 16:9
59.94 / 60 Hz 2 CH PCM OFF OFF ON
5
720 x 480p 4:3
1440 x 480p 4:3
720 x 480p 16:9
1440 x 480p 16:9
1280 x 720p 16:9
1920 x 1080i 16:9
*1920 x 1080p 16:9
59.94 / 60 Hz 2 CH PCM ON
8 CH PCM
DTS®
Dolby®
50 Hz
8
2 CH PCM ON
ON
OFF
OFF
OFF ON
OPERATING THE HDMI DETECTIVE PLUS
Writing an EDID using a source device
The HDMI Detective Plus allows a signal generator (or other source device)
to write an EDID to the Detective. This provides additional flexibility when
programming custom timings and refresh rates.
1. Make sure that the WR (write) switch on the HDMI Detective Plus is in the
“E” (enable write) position and make sure all DIP switches are in the OFF
position.
2. Use an HDMI cable to connect the source (generator) device to the HDMI In
port on the HDMI Detective Plus.
3. Connect the included 5V DC power supply to the HDMI Detective Plus.
4. Use the source (generator) device to send the EDID data to the HDMI
Detective Plus.
9
SPECIFICATIONS
Maximum Pixel Clock .............................................................................. 225 MHz
Input DDC Signal ............................................................................... 5V p-p (TTL)
Video Input Connector .............................................. HDMI Type A, 19-pin, female
Video Output Connector ........................................... HDMI Type A, 19-pin, female
Power Supply .............................................................................................. 5V DC
Power Consumption .............................................................................. 5W (max.)
Dimensions (W x H x D) ................... 2.7” x 1.5” x 2” (68.5mm x 38mm x 50.8mm)
Shipping Weight ............................................................................................ 2 lbs.
10
WARRANTY
Gefen warrants the equipment it manufactures to be free from defects in material
and workmanship.
If equipment fails because of such defects and Gefen is notified within two (2)
years from the date of shipment, Gefen will, at its option, repair or replace the
equipment, provided that the equipment has not been subjected to mechanical,
electrical, or other abuse or modifications. Equipment that fails under conditions
other than those covered will be repaired at the current price of parts and labor in
effect at the time of repair. Such repairs are warranted for ninety (90) days from
the day of reshipment to the Buyer.
This warranty is in lieu of all other warranties expressed or implied, including
without limitation, any implied warranty or merchantability or fitness for any
particular purpose, all of which are expressly disclaimed.
1. Proof of sale may be required in order to claim warranty.
2. Customers outside the US are responsible for shipping charges to and from
Gefen.
3. Copper cables are limited to a 30 day warranty and cables must be in their
original condition.
The information in this manual has been carefully checked and is believed to
be accurate. However, Gefen assumes no responsibility for any inaccuracies
that may be contained in this manual. In no event will Gefen be liable for
direct, indirect, special, incidental, or consequential damages resulting from
any defect or omission in this manual, even if advised of the possibility of such
damages. The technical information contained herein regarding the features and
specifications is subject to change without notice.
For the latest warranty coverage information, refer to the Warranty and Return
Policy under the Support section of the Gefen Web site at www.gefen.com.
PRODUCT REGISTRATION
Please register your product online by visiting the Register Product page
under the Support section of the Gefen Web site.
11
Rev A10
20600 Nordhoff St., Chatsworth CA 91311
1-800-545-6900
818-772-9100
www.gefen.com
Pb
This product uses UL or CE listed power supplies.
fax: 818-772-9120
support@gefen.com