Superthane and Urebrade Polyurethane Tubing and Hose in Ether

123c
Polyurethane
P
olyurethane combines the best
properties of both plastic and
rubber. It offers abrasion and tear
resistance, high tensile and
elongation values, and low
compression set. Polyurethane is
naturally flexible and exhibits
virtually unlimited flexural
abilities.
Combining good
chemical resistance with
excellent weathering
characteristics sets
polyurethane apart
from most other
thermoplastics. It has
exceptional resistance
to most gasolines, oils,
Superthane®
Transparent polyurethane
tubing . . . . . . . . . . . . . . . . . . . . . . . . . .2
Superthane Pneumatic
Colored polyurethane tubing
for pneumatics . . . . . . . . . . . . . . . . . .4
Urebrade®
Transparent braid reinforced
polyurethane hose . . . . . . . . . . . . . .6
Fluid Transfer Specialists ®
kerosene, and other petroleumbased chemicals, making it an
ideal choice for fuel lines
(although additives in today’s
gasoline and petroleum products
warrant field testing).
The two basic formulations of
urethane, ester and ether, have
some important differences.
Water attacks ester-based
urethane, causing a significant
reduction in physical properties.
Ether urethanes exhibit far
superior hydrolytic stability,
especially in humid environments. Ether-based materials also
resist fungus growth better than
ester-based materials. ■
Applications
■ Abrasive Powder Transfer ■ Agriculture ■ Air Tools ■ Automated
Machinery ■ Automotive ■ Cement Slurries ■ Computer Disc Drive
Equipment ■ Fluid Circuitry ■ Fluid Feeds ■ Granular Transfer
■ Grease & Lubrication Lines ■ Hydraulic Control Systems ■
Instrumentation ■ Insulating Sleeves ■ Lubricated Air Feeds ■
Metering Pumps ■ Oil & Fuel Lines ■ Oxygen & Gas Lines
■ Petroleum Products Transfer ■ Pneumatic Control Systems ■
Pressure Measuring Devices ■ Robotics ■ Sensing Systems ■ Small
Motor Fuel Lines ■ Transfer Lines for Clean Liquids ■ Transfer Lines
for Internal Contamination Fluids ■ Vacuum Equipment ■ Well Pipe
and Cable Jacket ■ More
Sign up for our eNewsletter at www.newageindustries.com/extrusions
Superthane
123c
®
Tr a n s p a r e n t Po l y u r e t h a n e Tu b i n g
■ Available in Ester or Ether formulations
■ Both formulations made from non-toxic raw materials conforming to
FDA standards for use with wet and fatty food contact surfaces
■ Extremely resistant to weathering†, tearing, impact, radiation, and
abrasion
■ Transparent, flexible, resilient, tough; resistant to oils, greases,
and fuels††
■ Wide range of temperature resistance: -85°F to 185°F (ester)
■ Ether-based raw material is listed by the National Sanitation
Foundation (NSF 61) for use with potable water
■ Ester-based raw material is free of animal derived
components and REACH compliant
■ Free of DEHP, phthalates, BPA and conflict minerals
Made in U.S.A.
■ RoHS compliant
■ Can be heat sealed, coiled, fabricated, or bonded
Custom Services
Notes
†Hydrolytic Stability — For resistance to
moisture and fungi, SUPERTHANE ether is
recommended. (Ester polyurethane does not react
well with water, prolonged humid conditions, or
attack from fungi.) The raw material used in its
manufacture is listed by the National Sanitation
Foundation (NSF 61).
SUPERTHANE is much more resistant to
pressure and vacuum applications than
corresponding sizes of PVC or rubber.
††Although polyurethane is commonly used in
fuel applications, due to additives in today’s
gasoline and petroleum products, field testing
should be performed.
When used with Thermobarb® fittings,
SUPERTHANE will not require clamps, provided
that working pressures remain at or below 105 psi
at ambient temperature.
Custom coiled polyurethane is available — call
for details.
For easy identification, SUPERTHANE is
imprinted with the trademarked name.
■ Cut
■ Size
■ Color
■ Overbraid
■ Hot Bond
■ Heat-Form
■ Hardness
■ And More
Call for more information: 800-506-3924 or 215-526-2300
Recommended Fittings & Clamps
■ Thermobarb® barbed fittings
■ Cam operated couplings
■ Oetiker® ear type clamps
■ Kwik Clamp™ nylon double bond hose clamps
■ Worm gear clamps
Physical Properties**
Hardness, Shore A ±5
Tensile Strength, psi
Elongation at Break, %
Brittle Temperature, °F
Maximum Operating Temp., °F
ESTER
85
6100
490
-85
185
ETHER
85
7500
500
-85
175
**Values listed are typical for the material used in
manufacture, except where noted, and are meant only as
a guide to aid in design. Field testing should be
performed to find the actual values for your application.
2
www.newageindustries.com
Meet Some of NewAge Industries’ Owners
Through an Employee
Stock Ownership Plan
(ESOP), we’re part
owners in the company,
and that makes your
satisfaction an investment in our future.
Molly Doheny
HR Generalist/
Owner
2 years
Randy Decker
Graphic & Web
Designer/Owner
20 years
Bunna Soth
Silicone Molding/
Owner
9 years
Superthane
123c
®
Tr a n s p a r e n t Po l y u r e t h a n e Tu b i n g
PART NO.
ESTER
PART NO.
ETHER
ID
(IN.)
OD
(IN.)
WALL
(IN.)
STANDARD
LENGTH
(FT.)
WORKING
PSI AT
70°F
200 0075
210 0070
210 0070
210 0147
.063
.063
.125
.125
.125
.170
.188
.188
.250
.250
.250
.313
.313
.313
.375
.375
.375
.375
.438
.500
.500
.500
.500
.625
.625
.625
.625
.750
.750
.875
1.000
1.500
2.000
.125
.125
.188
.188
.250
.250
.250
.313
.313
.375
.500
.438
.500
.563
.500
.500
.563
.625
.688
.625
.625
.688
.750
.750
.813
.813
.875
.938
1.000
1.125
1.250
1.750
2.250
.031
.031
.031
.031
.063
.040
.031
.063
.031
.063
.125
.063
.094
.125
.063
.063
.094
.125
.125
.063
.063
.094
.125
.063
.094
.094
.125
.094
.125
.125
.125
.125
.125
100
500, 5000
100
1000
100, 1500
500
100
100, 1000
100
100, 1000
100
100
100
100
100
500
100
100
100
50
100
50, 100
50, 100
100
50
100
50, 100
50, 100
50, 100
100
50, 100
25, 50, 100
25, 50
135
135
72
72
130
70
27
74
33
67
131
65
75
118
59
59
84
100
80
36
36
48
60
40
54
54
60
43
51
33
40
31
22
200
200
200
200
200
200
200
200
200
200
200
200
200
0152
0152
0229
0383
0460
0537
0768
0845
0999
1076
1153
1230
1307
200 1384
200 1461
200 1615
200 1692
200 1846
200 2000
200 2077
200 2231
200 2385
200 2539
210 0224
210
210
210
210
210
0455
0609
0686
0840
0917
210
210
210
210
1148
1148
1225
1302
210
210
210
210
210
210
210
210
210
210
210
210
210
210
1533
1533
1610
1687
1764
1841
1841
1918
1995
2072
2226
2380
2534
2688
LBS. PER
100 FT.
ESTER
.48
.79
.79
1.92
1.37
1.13
2.55
1.42
3.19
7.66
3.83
6.24
8.93
4.47
7.16
10.22
11.48
5.75
12.77
10.98
15.33
17.88
20.43
22.99
LBS. PER
100 FT.
ETHER
.45
.45
.74
1.77
2.38
1.33
2.98
7.15
3.57
4.17
4.17
6.68
9.54
5.36
5.36
8.47
11.92
6.56
10.25
10.25
14.30
12.03
16.69
19.07
21.46
30.99
40.53
Add length suffix to part number when ordering. Example: 100 ft. of 1/8” I.D. x 3/16” O.D. ester tubing is part number 200 0152-100.
Working pressures are calculated from burst testing using a 3:1 safety factor. Application testing is recommended.
Cut coils are available from coils of 100 ft. or less; charges apply — call for details. Coils over 100 ft. are sold by standard coil
length only. Due to the coil diameter, some larger sizes must ship via truck.
Tolerances: ID & OD ±3% but not less than ±.005".
BOLD indicates the critical dimension for fittings application.
More NewAge Industries’ Owners
www.newageindustries.com
Did you know . . . ?
We’ve successfully
undergone over 20
customer audits.
Chris Boytim
Quality Manager/
Owner
18 years
Nary Seng
Silicone Molding/
Owner
6 years
Russ Schrader
Customer Service
Rep./Owner
9 years
Bounnarith Tour
Plastic Manufacturing/Owner
7 years
Kathy Colon
Silicone Molding/
Owner
4 years
Dan Tropea
Director of Supply
Chain/Owner
1 year
3
Superthane Pneumatic
123c
®
C o l o r e d Po l y u r e t h a n e Tu b i n g f o r P n e u m a t i c s
■ Made from hydrolysis resistant, 85A durometer Ether polyurethane
■ Stocked in 8 colors plus clear for easy multiple line identification
■ Can be bonded into a multiple tube ribbon
■ Clamps not required when used with properly designed barbed
fittings at pressures of 105 psi or less
■ Naturally flexible for close-in bending — contains no plasticizers
which could migrate and cause tube hardening or flow
contamination
■ Resistant to weathering, kinking, tearing, abrasion, impact, and
radiation exposure
■ Wide range of temperature resistance: -90°F to 175°F
Made in U.S.A.
Custom Services
Notes
Ether-based SUPERTHANE PNEUMATIC tubing
is resistant to attack from moisture, humidity, and
fungi. SUPERTHANE PNEUMATIC has excellent
cold temperature flexibility and virtually unlimited
flexural life. The superior strength of SUPERTHANE
PNEUMATIC makes it more resistant to pressure
and vacuum than corresponding sizes of PVC or
rubber.
When used with Thermobarb® fittings,
SUPERTHANE PNEUMATIC will not require clamps,
provided that working pressures remain at or
below 105 psi at ambient temperature.
■ Hot Bond
■ Heat-Form
■ Hardness
■ And More
Call for more information: 800-506-3924 or 215-526-2300
85
5500
580
-90
175
**Values listed are typical for the material used in
manufacture, except where noted, and are meant only as
a guide to aid in design. Field testing should be
performed to find the actual values for your application.
Recommended Fittings & Clamps
■ Thermobarb® barbed fittings
■ Oetiker® ear type clamps
■ Kwik Clamp™ nylon double bond hose clamps
■ Worm gear clamps
4
■ Color
■ Overbraid
More NewAge Industries’ Owners
Physical Properties**
Hardness, Shore A ±2
Tensile Strength, psi
Elongation at Break, %
Brittle Temperature, °F
Maximum Operating Temp., °F
■ Cut
■ Size
www.newageindustries.com
Did you know . . . ?
100% of calls received
during normal business
hours are answered by a
person, not a machine.
Kippy Baird
Receptionist/Admin.
Asst./Owner
13 years
Rich MacDonald
Network Administrator/Owner
10 years
Rattanak Seng
Silicone Molding/
Owner
7 years
Chantha Cheng
Silicone Manufacturing/Owner
1 year
Sotharin Meth
Silicone Molding/
Owner
6 years
Chris Kourelias
Warehouse
Manager/Owner
12 years
Superthane Pneumatic
123c
®
C o l o r e d Po l y u r e t h a n e Tu b i n g f o r P n e u m a t i c s
SUPERTHANE PNEUMATIC – Transparent Colors
PART NO.
RED
PART NO.
YELLOW
PART NO.
BLUE
PART NO.
GREEN
PART NO.
CLEAR
211 0605 211 0626 211 0535 211 0563 210 0070*
211 1235 211 1256 211 1165 211 1193 210 0224*
ID
(IN.)
OD
(IN.)
WALL
(IN.)
STANDARD
LENGTH
(FT.)
1/16
1/8
1/8
1/4
1/32
1/16
100, 1000
100, 1000
WORKING BURST
PSI AT
PSI AT
70°F
70°F
135
130
405
390
*Not available in 1000 ft. lengths, although other lengths are available — 210 0070 in 500 and 5000 ft.; 210 0224 in 1500 ft.
Sold by standard coil length only. 1000 ft. lengths are supplied on spools. Add length suffix to part number when ordering.
Example: 100 ft. of 1/16” I.D. yellow tubing is part number 211 0626-100.
Weight, lbs. per 100 ft.: 1/16” I.D. tubing = .45; 1/8” I.D. tubing = 1.79
BOLD indicates the critical dimension for fittings application.
SUPERTHANE PNEUMATIC – Opaque Colors
PART NO.
GRAY
PART NO.
BLACK
PART NO.
WHITE
PART NO.
ORANGE
ID
(IN.)
OD
(IN.)
WALL
(IN.)
STANDARD
LENGTH
(FT.)
211 1200
211 0528
211 1158
211 0619 †
211 1249
211 1221†
1/16
1/8
1/8
1/4
1/32
1/16
100, 1000
100, 1000
WORKING BURST
PSI AT
PSI AT
70°F
70°F
135
130
405
390
†Not available in 1000 ft. lengths.
Sold by standard coil length only. 1,000 ft. lengths are supplied on spools. Add length suffix to part number when ordering.
Example: 1,000 ft. of 1/8” I.D. gray tubing is part number 211 1200-1000.
Weight, lbs. per 100 ft.: 1/16” I.D. tubing = .45; 1/8” I.D. tubing = 1.79
BOLD indicates the critical dimension for fittings application.
More NewAge Industries’ Owners
Did you know . . . ?
The average length of
time a Sales Team
Member has been with
NewAge is eight years.
Ken Liszewski
Key Account
Manager/Owner
16 years
Janine Clarkson
Document ControlQuality/Owner
1 year
Terrell Graves
Plastic Manufacturing/Owner
1 year
Janet MacFarlane
Customer Service
Rep./Owner
4 years
Peter Chao
Silicone Manufacturing/Owner
15 years
Steven Choing
Plastic Manufacturing/Owner
6 years
Bill Keiser
Senior Quality
Auditor
6 years
Cuong Nguyen
West Coast Sales
Manager/Owner
1 year
Lorrie McGough Chhoeuth Chhour
Accounting/Owner Silicone Mfg./Owner
15 years
1 year
www.newageindustries.com
5
Urebrade
123c
®
Tr a n s p a r e n t B r a i d R e i n f o r c e d P o l y u r e t h a n e H o s e
■ Open mesh polyester braiding incorporated within the wall of flexible,
ether-based polyurethane
■ Made from non-toxic raw ingredients conforming to FDA standards
■ Raw materials are listed by the National Sanitation Foundation
(NSF 61) for use with potable water
■ Offers much greater pressure capability than unreinforced
polyurethane tubing
■ Resistant to weathering†, tearing, impact, abrasion,
radiation exposure, oils, greases, and fuels††
■ Wide range of temperature resistance; -90°F to 175°F
Made in U.S.A.
■ Free of DEHP, phthalates, BPA and conflict minerals
■ RoHS compliant
■ Naturally transparent for visual contact with the flow
PART NO.
Notes
†Hydrolytic Stability — UREBRADE is
supplied in an ether formulation, making it
resistant to attack from moisture and fungi.
The raw materials used in UREBRADE are
listed by the National Sanitation Foundation
(NSF 61).
Where applications involve repeated
flexing, heavy vibration, or abrasion,
UREBRADE offers superior service life over
other materials.
Ester-based UREBRADE is available
through minimum order — call for details.
††Due to additives in today’s gasoline
and petroleum products, field testing should
be performed.
For easy identification, transparent
UREBRADE is imprinted with the
trademarked name.
Physical Properties**
Hardness, Shore A ±5
Tensile Strength, psi
Elongation at Break, %
Brittle Temperature, °F
Max. Operating Temperature, °F
85
5500
580
-90
175
**Values listed are typical for the material used in
manufacture, except where noted, and are meant only as
a guide to aid in design. Field testing should be
performed to find the actual values for your application.
6
220
220
220
220
220
220
220
220
220
0072
0149
0226
0303
0380
0457
0534
0611
0688
ID
(IN.)
OD
(IN.)
WALL
(IN.)
STANDARD
LENGTH
(FT.)
.250
.375
.500
.625
.750
1.000
1.250
1.500
2.000
.470
.630
.750
.905
1.025
1.300
1.710
1.930
2.500
.110
.127
.125
.140
.137
.150
.230
.215
.250
50, 100
50, 100
25, 50, 100
25, 50, 100
25, 50, 100
25, 50, 100
25, 50, 100
25, 50, 100
25, 50, 100
250
190
150
130
100
80
75
50
40
.750
.750
1.500
2.000
3.000
3.500
4.000
5.500
7.500
6.04
9.78
11.92
16.34
18.62
26.32
51.94
56.26
85.82
Add length suffix to part number when ordering. Example: 100 ft. of .250” I.D. x .470” O.D.
hose is part number 220 0072-100.
Working pressures are calculated from burst testing using a 4:1 safety factor. Application
testing is recommended.
Cut coils available; charges apply — call for details.
Due to the coil diameter, some larger sizes must ship via truck.
BOLD indicates the critical dimension for fittings application.
Custom Services
■ Cut
■ Size
■ Color
■ Overbraid
■ Hot Bond
■ Heat-Form
■ And More
Call for more information: 800-506-3924 or 215-526-2300
More NewAge Industries’ Owners
Recommended Fittings & Clamps
Did you know . . . ?
■ Thermobarb® barbed fittings
■ Cam operated couplings
■ Oetiker® ear type clamps
■ Kwik Clamp™ nylon double bond hose clamps
■ Worm gear clamps
100% of our extruded
tubing is continuously
inline laser monitored
for size.
www.newageindustries.com
WORKING BEND LBS. PER
PSI AT RADIUS 100 FT.
70°F
(IN.)
Kathi Lohr
Buyer/Planner/
Owner
1 year
Mark Mistretta
Regional Sales
Manager/Owner
1 year
Samang Hout
Silicone Manufacturing/Owner
12 years
Custom & Fabrication Services
123c
C r e a t e P a r t s C u s t o m i z e d t o M e e t Yo u r N e e d s
Going beyond basic tubing, hose, and fittings has been an integral part of
NewAge Industries' business for many years. We possess the capabilities and
experience to create custom parts perfectly suited to your application. Postextrusion fabrication and hose assembly opens another range of options
for providing parts to your exact specifications at a reasonable cost.
■ Custom Coiling
■ Custom Extrusions
■ Overbraiding & Jacketing
■ Hot Bond® - Thermal Bonding
■ Heat Formed Shapes
■ Fabrication Services - Cutting, Slitting, Printing, etc.
■ Hose Assemblies
■ Dip Molded Tubing
■ Molded Silicone Components
■ And More
Discuss your application with someone from
our knowledgeable Sales Team today
800-506-3924 or 215-526-2300
Meet Some of NewAge Industries’ Owners
Through an Employee Stock Ownership Plan (ESOP), NewAge employees
are part owners in the company. Our jobs are part of an investment in our
future, and that’s reflected in our communications with customers and
suppliers, and with each other, now more than ever. When a customer calls,
they can speak with an owner.
Cathy Wallace
Demand Planning
Manager/Owner
27 years
Siravuth Sinn
Silicone Molding/
Owner
1 year
Hemant Patel
Silicone Manufacturing/Owner
7 years
Cinthya Quispe
Manufacturing
Engineer/Owner
2 years
John Fox
Plant Engineer/
Owner
15 years
Savit Mann
Tony Szoka
Silicone Molding/
Territory Sales
Owner
Rep./Owner
6 years
1 year
www.newageindustries.com
7
More NewAge Industries Products
Tubing & Hose
Fittings & Clamps for Polyurethane
PVC
Polyurethane
Silicone
Fluoropolymer
Nylon
Polyethylene
Polypropylene
TPR
Viton™
Latex
Hytrel®
Thermobarb® Plastic - Precision molded barbed
Custom Services
Cut
Size
Color
Coil
Overbraid
Heat Form
Hot Bond®
Assemblies
Hardness
More
fittings in nylon-6, high density polyethylene, PVDF,
polypropylene, reinforced nylon, or reinforced polypropylene. Sizes for 1/8” to 1” I.D. tubing in 15 styles.
Thermobarb® Brass - Durable brass barbed fittings.
Sizes for 1/8” to 1” I.D. tubing in 10 styles.
Cam Operated Couplings - Molded from glass-fiber
reinforced nylon or glass-fiber reinforced
polypropylene. Sizes from 3/8” to 4” in 8 styles.
Oetiker® Ear Type Clamps - Stainless steel or zincplated carbon steel clamps with a unique breathable
design. 35 sizes from 5/32” to 1-9/16” in 3 styles.
Kwik Clamp™ - Nylon double-bond hose clamps.
31 sizes from 1/4” to 4-1/4” nominal O.D.
Worm Gear Clamps - Stainless steel worm screw
clamps. 28 sizes from 3/8” to 6” in 6 styles.
Tubing & Hose Cutting Tools
High Purity Tubing & Hose
Sanitary tubing, hose, fittings,
assemblies, and molded components
from our AdvantaPure division meet
the needs of the pharmaceutical,
biotech, food and beverage, dairy,
cosmetics and fragrances, and chemical
industries, as well as other sanitary
applications. AdvantaPure products are
available through a network of select
distributors. www.advantapure.com
Superthane, Urebrade, Hot Bond, Kwik Clamp, Thermobarb, NewAge, “Fluid Transfer Specialists,” The "N" Logo, and AdvantaPure are trademarks of NewAge® Industries, Inc. • Oetiker reg. TM Oetiker, Inc. • Hytrel trademark E. I. du Pont de Nemours and Company • Viton trademark The Chemours Company
WARRANTY: NewAge Industries’ products are warranted to be free from defects in material and workmanship. Any product found to carry such defects will be replaced without charge. This warranty is limited only to the replacement of NewAge Industries' products, item for item, which after examination by
NewAge Industries are deemed defective. NewAge Industries specifically disclaims any other liability. The data supplied is provided as a helpful guideline and is believed to be reliable; however, nothing stated shall constitute a guarantee, recommendation, or warranty for any application.
NOTICE: NewAge Industries, Inc. has been a privately owned corporation since 1954. Neither the corporation nor its principals are affiliated, in any way, with any other group or entity either representing themselves as or being referred to by the term New-Age.
© NewAge Industries, Inc. 2016
Specifications are subject to change without notice.
DISTRIBUTOR PARTNER
9/14/16
123c
145 James Way
Southampton, PA 18966
www.newageindustries.com
800-50-NEWAGE
(800-506-3924)
215-526-2300
Fax: 800-837-1856
215-526-2190
info@newageindustries.com