Tapered Internal Product Catalog

Transcription

Tapered Internal Product Catalog
ORDERING & WARRANTY INFORMATION
Product Support Specialist:
Cell phone:
Fax:
BioHorizons USA
Customer Care/Servicio al Cliente: 888-246-8338 / 205-967-7880
BioHorizons Canada
Customer Care/Service à la Clientèle: 866-468-8338 / 905-944-1700
BioHorizons Ibérica
Atención al Cliente: +34 91 713 10 84
BioHorizons UK
Customer Care: +44 8700 620 550
BioHorizons GmbH
Kunden Service: +49 7661-909989-0
BioHorizons Australia
Customer Service: +61 2 8399 1520
BioHorizons Mexico
Servicio al Cliente:
+52 55 5545 1297
BioHorizons Chile
Atención al Cliente:
+56 2 475 7230
BioHorizons No Exceptions Lifetime Warranty on Implants and Prosthetics:
BioHorizons implants and prosthetic components carry a Lifetime Warranty. We will replace any BioHorizons implant or prosthetic component if removal of
that product due to failure (excluding normal wear to overdenture attachments) is required for any reason, at any time.
Warranties on Instruments, Surgical Drills, Taps and Torque Wrenches:
BioHorizons warranties instruments, surgical drills and taps and torque wrenches for the period specified for each in (1) & (2) below. During the specified
warranty period we will replace or repair any product with a defect in material or workmanship.
(1) Instruments: The warranty on BioHorizons instruments extends for a period of one (1) year from the date of initial invoice. This
includes drivers, sinus lift components, implant site dilators and other BioHorizons tools used in the placement or restoration of our
implants, with the exception of surgical drills and taps (see below).
(2) Surgical Drills and Taps: Surgical drills and taps are warrantied for a period of 90 days from the date of initial invoice. Surgical drills and
taps should be replaced when they are worn, dull, corroded or in any way compromised. BioHorizons recommends the replacement
of drills after 12 to 20 osteotomies.1
Return Policy:
Instructions for initiating returns can be found on the reverse side of the invoice that was shipped with the product. Please contact Customer Care if you need
a copy of the instructions or if you have additional questions or requests.
BioHorizons strongly recommends completion of postgraduate dental implant education and strict adherence to the Instructions for Use (IFU) that
accompany our products. Treatment planning and use of the products are solely your responsibility. BioHorizons is not responsible for incidental
or consequential damages or liability relating to use of our products alone or in combination with other products, other than replacement or
repair under our warranties. BioHorizons continually strives to improve its products and therefore reserves the right to improve, modify, change
specifications or discontinue products at any time.
TABLE OF CONTENTS
Ordering & Warranty Information
Icon Legend
Implant Overview
Laser-Lok® Overview
inside cover
3
5
6
Section 1: Surgical
Implants
Packaging/Cover Caps
Healing Abutments
Surgical Kit/Individual Components
Template, Manuals & Catalogs
7
8
9-10
11-13
14
15-16
17
W&H Motors & Accessories
Ancillary Instruments
Section 2: Restorative
Simple Solutions Kits & Components
Individual Abutment Selection
Impression Component Selection
Individual Abutments
3inOne & Temporary Abutments
Angled Abutments
Profile Abutments
Narrow & Ceramic Abutments
Custom Castable Abutments
Implant Analogs & Screws
Impression Components
Indirect Transfer Copings
Direct Pick-up Copings
19-22
23
24
25
26
27
28
29
30
31
32
Overdenture Components
Abutment for Screw
Abutment for Screw Components
Locator Abutments
Locator Components
Ball Abutments / O-rings
Ball Abutment Components
Prosthetic Instrumentation
Patient Education Materials
References
33
34
35
36
37
38
39-40
41
42
I CO N L E G E N D
Symbol descriptions for product labeling
LOT
Lot/batch number
REF
Reference/article number
STERILE R
Prosthetic platform
3.5
Ø3.5mm Prosthetic Platform
4.5
5.7
Sterile by gamma irradiation
NON-STERILE Non-sterile
Rx Only
Caution: Federal (USA) law restricts
these devices by, or on the order of, a
dentist or physician.
Implant diameter : surface treatment
Single use only
Ø3.8
Ø3.8mm Implant: RBT
Refer to Instructions for Use
Ø4.6
Use before expiration date (YYYY-MM)
Manufacture date (YYYY-MM)
Ø5.8
BioHorizons products carry the CE
mark and fulfill the requirements
of the Medical Devices Directive
93/42/EEC
Disclaimer of Liability
BioHorizons dental implants may only be used in conjunction with the associated original components and instruments according to
BioHorizons Instructions for Use. Use of any non-BioHorizons products in conjunction with BioHorizons implants will void any warranty
or any other obligation, expressed or implied, of BioHorizons.
This literature serves as a reference for BioHorizons Tapered Internal implants, prosthetics and instrumentation. It is not intended to
describe the methods or procedures for diagnosis, treatment planning, or placement of implants, nor does it replace clinical training or
a clinician’s best judgment regarding the needs of each patient. BioHorizons recommends appropriate training as a prerequisite for the
placement of implants and associated treatment.
Validity
Upon its release, this literature supersedes all previously published versions.
Availability
Not all products shown or described in this literature are available in all countries.
SECTION 1: SURGICAL
Implants
Healing Abutments
Surgical Kit & Components
Surgical Motors
IMPL ANT OVERVIEW
BioHorizons Tapered Internal features
• Proprietary Laser-Lok® microchannels*
• Anatomically tapered implant body
• Patented reverse buttress threads**
• Proven internal hex connection
Laser-Lok 8 micron channels
inhibit epithelial downgrowth.
Supported by a
comprehensive line of
internally hexed prosthetics.
Laser-Lok 12 micron channels
attach and retain crestal bone.
Resorbable Blast Texturing
(RBT) provides a highly complex
surface texture for increased
stability and osseointegration.
Reverse Buttress Threads
have a wide, flat leading
edge for increased surface
area and improved axial
load distribution.
* Laser-Lok design patent #6,454,569 and 6,419,491.
** Reverse Buttress thread design patent #5,964,766.
L A S E R- LO K ® OV E R V I E W
BioHorizons Laser-Lok Technology
Laser-Lok microchannels are a series of 8 micron and 12 micron grooves
that are engineered onto the collar of our Tapered Internal Implants.
This precision laser surface is patented and unique within the industry
as the only surface treatment shown to inhibit epithelial downgrowth,
attach and retain crestal bone and engineer a biological width5 and tissue
attachment.
Microchannels viewed using scanning electron microscopy (SEM) at 1000X
Laser-Lok microchannels are the result of over 15 years of research and
documented studies at leading Universities. As part of the research,
numerous in-vitro and in-vivo studies were conducted to (1) understand
how bone and soft tissue cells react to various types of surface geometries
and (2) evaluate how specific surface microgeometries affect crestal bone
and the biologic width around dental implants.
In-vitro Research
Cellular activity was studied on a variety of surface finishes including
smooth, roughened and specifically engineered microgeometries. The
engineered microgeometries were designed in a variety of repeating
patterns and in a number of different sizes. Through various cell model
designs, it was shown that a linear grooved pattern in the range of 8 to 12
microns was optimal for inhibiting cell growth,2 maximizing cellular contact
guidance3 and providing a directed tissue response.4
Fibroblasts on a 12 micron
channeled surface4
Fibroblasts on a smooth surface4
In-vivo Validation
A series of animal studies (rabbit and canine) were conducted
in both an implantable chamber model (intended to assess
biologic response) and a dental model to assess the differences
in tissue response to an engineered microgeometry versus a
machined surface (control). Through these studies, it was shown
that a microchannel pattern of 8 and 12 microns improved soft
tissue integration,5 controlled cell ingrowth,6 increased bone
and tissue attachment7 and reduced bone loss.8
Light photomicrograph showing
connective tissue attachment to the
laser-machined surface7
SEM showing bone integration of
the implant body
Clinical Evidence
To evaluate how dental implants treated with the Laser-Lok microchannels
benefit patients, a series of human histologic case studies and prospective
controlled studies have been conducted. In a prospective, controlled
multi-center study conducted by the Group for Implant Research in Italy,
it was shown that, at 37 months post-op, the mean crestal bone loss for
implants with Laser-Lok microchannels was only 0.59mm versus 1.94mm
for the control implant.9 Similarly, a prospective, randomized study has
been initiated comparing an implant with Laser-Lok microchannels to
the 3i Osseotite® NT implant and the Nobel-Biocare Select. This study is
evaluating the peri-implant bone and soft tissue complex in patients at 6,
12, 24 and 36 months post-restoration.
Histologic slides showing bone remodeling near the implant surface and
no resorption areas at the tips of the threads10.
IMPLANTS
BioHorizons Tapered Internal Implants
Each implant includes a 3inOne Abutment, Cover Cap and Abutment Screw. .
Order by length and diameter. Titanium Alloy [Ti-6Al-4V].
0.3mm machined
collar
1.5mm Laser-Lok
surface
Tapered Internal Implants have a 0.3mm machined collar between the
implant/abutment interface and the top of the Laser-Lok surface treatment.
Ø3.5mm
prosthetic platform
RBT Surface
with Laser-Lok
Body Diameter x Length
TLR3809
Ø3.8mm x 9mm
TLR3810
Ø3.8mm x 10.5mm
TLR3812
Ø3.8mm x 12mm
TLR3815
Ø3.8mm x 15mm
length
body diameter
Ø3.8mm
Ø4.5mm
prosthetic platform
RBT Surface
with Laser-Lok
TLR4607
Ø4.6mm x 7.5mm
TLR4609
Ø4.6mm x 9mm
TLR4610
Ø4.6mm x 10.5mm
TLR4612
Ø4.6mm x 12mm
TLR4615
Ø4.6mm x 15mm
length
body diameter
Ø4.6mm
RBT Surface
with Laser-Lok
Ø5.7mm
prosthetic platform
TLR5807
Ø5.8mm x 7.5mm
TLR5809
Ø5.8mm x 9mm
TLR5810
Ø5.8mm x 10.5mm
TLR5812
Ø5.8mm x 12mm
TLR5815
Ø5.8mm x 15mm
length
body diameter
Ø5.8mm
PACKAGING | COVER CAPS
Implant Packaging
REF TLR4612
REF TLR4612
Tapered Internal Implant
RBT, Laser-Lok
Ø4.6 x 12mm, 4.5 Platform
LOT S1208242
do not re-use
STERILE R Rx Only
gamma irradiated
2008 -12
R R
4.5 4.5
Implant Diameter / Surface
2013 -12
expires
R
2008 -12
manufacture date
gamma irradiated
L0127 Rev B
BioHorizons Implant Systems, Inc. Birmingham, AL 35243 USA
0473
do not re-use
STERILE R Rx Only
2013 -12
expires
RBT, Laser-Lok
L0127 Rev B
S1208242
BioHorizons Implant Systems, Inc. Birmingham, LOT
AL 35243
USA
2008 -12
manufacture date
gamma irradiated
expires
2013 -12
do not re-use
STERILE R Rx OnlyREF0473
TLR4612
RBT, Laser-Lok
LOT S1208242
Part Number
0473
manufacture date
Ø4.6
Prosthetic
Platform
Implant
Diameter
/ Surface
Prosthetic
Platform
Implant
Diameter
/ Surface
Prosthetic
Platform
Implant Diameter
/ Surface
R
Prosthetic Platform
4.5
Tapered
Internal
RBT, LL
Internal
Implant,
Tapered Tapered
Internal
Implant,
RBT, Implant,
LL RBT, LL
4.5
x 12mm,
4.5 Platform
Ø4.6 xØ4.6
12mm,
4.5 Platform
Ø4.6 x 12mm,
4.5
Platform
Tapered Internal Implant, RBT, LL
L0127 Rev B
Ø4.6 Ø4.6
Surgical Cover Cap
Implant surface treatment
RBT, Laser-Lok
REFdimensions
TLR4612
and
Ø4.6 x 12mm,
4.5
Platform
Tapered
LOT S1208242 Internal Implant
REF TLR4612
RBT,
Laser-Lok
Ø4.6
x 12mm,
4.5Implant
Platform
Tapered
Internal
REF
TLR4612
2013 -12
LOT S1208242
expires
RBT,
Laser-Lok
do not re-use
Tapered
Internal
Implant
x 12mm,
STERILE Lot
RØ4.6
Number
04734.5 Platform
Rx
Only
gamma irradiatedRBT, Laser-Lok
LOT2013
S1208242
Ø4.6
x -12
12mm, 4.5 Platform
2008 -12 expires
manufacture date
do not re-use
LOT
S1208242
STERILE
R Rx Only
0473
2013 -12
Expiration
Date
expires
L0127 Rev B
do not re-use
2008 -12
BioHorizons Implant Systems, Inc. Birmingham,
AL 35243 USA
manufacture
STERILE
2013
-12R date
0473
Rx Only
Ø4.6
See Instructions for Use Inside
Tapered
Internal
Tapered
Internal
Tapered
Internal
Implant
System
Implant
System
Implant
System
Instructions
for Use
Inside
See See
Instructions
Use
Inside
See Instructions
for Usefor
Inside
Ø4.6
Tapered Internal
Implant System
Ø4.6
Body diameter and
surface treatment icon
Ø4.6
R
R
4.5
Prosthetic Platform
4.5
4.5
Prosthetic Platform
Prosthetic
Platform
Tapered
Internal
R
Implant System
LL
Prosthetic platform icon
Tapered Internal
Implant System
REF TLR4612
BioHorizons Tapered Internal implants are provided in double-layer packaging (as depicted below). A cardboard sleeve protects a
blister pack that contains the implant in a sterile inner vial. Only the sterile inner vial should be introduced into the sterile surgical field.
The blister tray lid has multiple peel-and-stick labels for affixing to the patient’s chart.
gamma irradiated
expires
gamma
irradiated
do not re-use
STERILE
R Rx Only 0473
2008
-12
L0127 Rev B
gamma
irradiated date
manufacture
2008 -12
manufacture date
L0127 Rev B
L0127 Rev B
For use during submerged surgical healing. Hand-tighten with the .050” (1.25mm) Hex Driver. Titanium Alloy [Ti-6Al-4V]. Included with implant but can
also be ordered separately.
P YC C
PGCC
PBCC
3.5mm Cover Cap
4.5mm Cover Cap
5.7mm Cover Cap
HEALING ABUTMENTS
Emergence Profile
Healing Abutments are used for tissue healing at second-stage uncovery, or as the transmucosal element for a single-stage procedure. Three factors should
be considered when ordering Healing Abutments:
1) The Diameter must be the same as the prosthetic platform width of the corresponding implant, either Ø3.5mm, Ø4.5mm or Ø5.7mm.
2) The Height of the Healing Abutment is typically chosen based upon the soft tissue thickness. Available heights are 1mm, 3mm and 5mm.
3) The Emergence Profile (Narrow, Regular or Wide) should be chosen to match the desired emergence of the final restoration. For example: if the
final restoration calls for a Wide Emergence Profile Abutment, the Healing Abutment and Impression Coping used should also be Wide Emergence.
Following this protocol will make the seating of prosthetic components much easier by contouring the soft tissue away from the prosthetic platform.
Note: Custom Cast Abutments do not specify an emergence since the emergence will be determined by the contour of the custom restoration.
Narrow
N
4.5
Regular
R
4.5
Wide
W
4.5
HEALING ABUTMENTS
Healing Abutments
Available in three heights to accommodate various tissue thickness: 1mm, 3mm and 5mm. Emergence (Narrow, Regular or Wide) should be chosen
based upon the desired emergence of the final restoration. Hand-tighten with the .050” (1.25mm) Hex Driver. Titanium Alloy [Ti-6Al-4V].
1mm
3mm
5mm
PYNHA1
3.5mm Narrow Healing Abutment, 1mm Height
PYNHA3
PYNHA5
R
PYRHA3
3.5mm Regular Healing Abutment, 3mm Height
3.5
PYRHA5
PYWHA3
3.5mm Wide Healing Abutment, 3mm Height
PYWHA5
PGNHA1
PGNHA3
PGNHA5
R
PGRHA3
4.5
PGRHA5
W
PGWHA3
PGWHA5
PBNHA1
PBNHA3
PBNHA5
R
PBRHA3
5.7
PBRHA5
N
3.5
W
3.5
1mm
3mm
5mm
N
4.5
4.5
1mm
3mm
5mm
N
5.7
10
SURGICAL KIT | INDIVIDUAL COMPONENTS
Tapered Internal Surgical Kit
TSK2021
Tapered Internal Surgical Kit (complete)
Includes all instruments shown on pages 11-13.
TSK2011
Tapered Internal Tray & Lid (without instruments)
Individual Surgical Kit Instruments
TSD2020
2.0mm Starter Drill
TSD2025
2.5mm Depth Drill
122-100
Drill Extender (adds 16mm of length)
144-100
Straight Parallel Pins (2 per kit)
144-200
20° Angled Parallel Pins (2 per kit)
TSD2032
3.2mm Width Increasing Drill
TSD2037
TSD2041
TSD2047
TSD2054
11
TSC2038
3.8mm Crestal Bone Drill
TSC2046
TSC2058
TST2038
3.8mm Bone Tap
TST2046
4.6mm Bone Tap
TST2058
5.8mm Bone Tap
TDG2038
3.8mm Depth Gauge
TDG2046
4.6mm Depth Gauge
TDG2058
5.8mm Depth Gauge
PHA
Abutment-level Driver, Handpiece
PRA
Abutment-level Driver, Ratchet
SYGIDH
3.5/4.5mm Implant-level Driver, Handpiece
SBIDH
5.7mm Implant-level Driver, Handpiece
SYGIDR
3.5/4.5mm Implant-level Driver, Ratchet
SBIDR
5.7mm Implant-level Driver, Ratchet
12
135-351
.050” (1.25mm) Hex Driver
300-400
Hand Wrench
300-205
Ratchet & Hand Wrench Extender
130-000
Ratchet
144-300
Implant Spacer / Depth Probe
13
TEMPLATE, MANUALS & CATALOGS
Radiographic Template
L0135
Tapered Internal Radiographic Implant Template (overlay)
Designed to aid the clinician in the preoperative determination of options for
implant length and diameter. The clear overlay template shows all sizes of
BioHorizons Tapered Internal implants in 100% and 125% scale. Please refer to
the BioHorizons Tapered Internal Surgical Manual (L0603, see below) for detailed
instructions for use.
Technical Manuals & Catalogs
L0603
Tapered Internal Surgical Manual
Describes surgical protocols and instruments used with the BioHorizons Tapered
Internal System. Step-by-step written instructions are coupled with detailed graphics
to illustrate implant placement.
ML0142
Simple Solutions Prosthetic Technique Manual
Guides the clinician and laboratory through impression making techniques and
prosthetic/lab procedures with the BioHorizons Simple Solutions components.
ML0118
Internal Prosthetic Technique Manual
Detailed information on prosthetic/lab procedures with the BioHorizons Internal
System components, compatible with Tapered Internal system implants. Step-by-step
written instructions are coupled with detailed graphics to illustrate procedures.
ML0203
Regeneration Product Catalog
Ordering information on AlloDerm®, Grafton DBM®, MinerOss®, the Bone Fixation
Screw Kit and AutoTac® Titanium tacking system. Also shown are a wide array of bone
and soft-tissue grafting instruments.
14
W&H MOTORS & ACCESSORIES
W&H ImplantMed 915
WH-915
W&H ImplantMed 915 Starter Kit
Re-order items:
WH-ITC915
WH-IC
WH-915MC
WD-79M
WH-915 One-piece Disposable Irrigation Set (6 pack)
Irrigation Clip for WI-75MB Handpiece
ImplantMed 915 Motor Cable - 1.8 meter
W&H Endo Contra-Angle 2:1 Handpiece WD-79
Not included in Starter Kit. 2:1 speed-reducing ratio.
Used with ImplantMed 915 for mechanical root canal preparation.
Maximum motor speed is 40,000 rpm. The motor comes with the WI-75MB 20:1 handpiece, bur testing gauge, (3) disposable irrigation assemblies, and
service oil (shipped separately). The starter kit has factory-programmed settings for endodontic functions when used with the W&H Endo Contra-angle
2:1 Handpiece.
W&H ElcoMed SA-200
WH 200
W&H ElcoMed SA-200 Professional Kit
Re-order items:
WH-200PTWC
WH-200RPT (3 PK)
WH-200INI
WH-200DOC
WH-200MC
Pump Tube (190mm) with Connectors
Replacement Pump Tubes (190mm) (3 pack)
INI Cards (3 pack)
DOC Cards (3 pack)
ElcoMed 200 Motor Cable -1.8 meter
Maximum motor speed is 50,000 rpm. The SA-200 permits the storage of torque characteristics of a treatment stage, which can then be saved on a DOC card
for archiving purposes. The kit also includes the WS-75 20:1 handpiece, (10) disposable spray tubes, bur testing gauge, irrigation spike and service oil (shipped
separately).
Universal and Legacy Re-order Items
Ref. Code
Description
Motor Compatibility
WH-ST (10 PK)
Green Single-Use Spray Tubes (10 pack)
All W&H Motors
WH-CLP (10 PK)
WH-100PTWC
WH-100RPT (5 PK)
WH-100MC
WH-110MC
WH-110CLP (5 PK)
WH-110PTWC
WH-110RPT (3 PK)
WH-110ISAWRC
WH-110RC
WH-ISA
WH-ITWOS
WH-MD400
WH-OSC
WH-SP
Set of Spray Tube Clamps (10 pack)
Pump Tube with Connectors (65mm)
ElcoMed 100 Motor Cable -1.8 meter
ImplantMed 110 Motor Cable -1.8 meter
Set of Spray Tube Clamps (5 pack)
Pump Tube (85mm) with Connectors
Irrigation Spike Assembly with Roller Clamp
Flow Regulating Roller Clamp
Irrigation Spike Assembly (autoclavable)
Irrigation Tubing w/o Spike (autoclavable)
ElcoMed 100 & 200
ElcoMed 100
ElcoMed 100
ElcoMed 100
ImplantMed 110
ImplantMed 110 & 915
All W&H Motors
All W&H Motors
All W&H Motors
All W&H Motors
All W&H Motors
MD-400 Service Oil-F1
Oil Spray Cap
Sterilization Plug for Motor Cable
15
W&H MOTORS & ACCESSORIES
IMPORTANT NOTE: W&H motors and handpieces are distinguished by their precision craftsmanship and reliability
and are covered by a 1-year manufacturer’s warranty. Instructions for required cleaning and maintenance are outlined
in each product’s user manual, and adherence to these procedures is essential for proper function and longevity of the
products. BioHorizons assumes no liability for the failure of, or damage to, motors and handpieces that are not properly
maintained or used contrary to the instructions for use. Please contact your Product Support Specialist or Customer Care
if you need additional information.
W&H ElcoMed Surgical Handpieces
WI-75MB
W&H 20:1 Contra-Angle Handpiece WI-75MB
Contra-Angle Handpiece with speed reduction ratio of 20:1 (2,000 rpm maximum with
ImplantMed 915). Equipped for both internal cooling & external cooling. Push-button bur
release. Monoblock construction. External Spray Clip (WH-IC) detaches for easy cleaning.
Uses latch-type surgical drills and burs.
WS-75
W&H 20:1 Contra-Angle Handpiece WS-75
Contra-Angle Handpiece with speed reduction ratio of 20:1 (2,500 rpm maximum).
Equipped for both internal cooling & external cooling. Push-button bur release. Uses
latch-type surgical drills and burs.
WS-92
W&H 1:2.7 Contra-Angle Speed Increasing Handpiece
1:2.7 speed-increasing ratio - 135,000 rpm maximum. Contra-Angle Handpiece suitable
for high speed preparation and tissue augmentation procedures. External irrigation port.
Uses friction-grip burs (Ø1.6mm).
S-11
W&H 1:1 Straight Surgical Handpiece
1:1 ratio - 50,000 rpm maximum. Suitable for bone harvesting, third molar extractions
and osteoplasty. Easily dismantled for cleaning. Uses 45mm friction-grip surgical burs
(Ø2.35mm).
S-12
W&H 1:2 Contra-Angle Surgical Handpiece
1:2 speed increasing ratio - 80,000 rpm maximum. Suitable for surgical procedures such
as bone smoothing, third molar extractions and osteotomy site drilling. High precision
bearings ensure that the unit runs vibration free. Uses friction-grip surgical burs at least
65mm long (Ø2.35mm).
Hex Drivers for Latch-Type Reduction Handpieces
134-350
134-450
.050” (1.25mm) Handpiece Hex Driver
.050” (1.25mm) Handpiece Hex Driver, Long
For installation and removal of Cover Caps, Healing Abutments and Abutment Screws. Use with latchtype contra-angle handpieces: WS-75 or WI-75MB, or similar. 134-450 is 5mm longer than the 134-350.
Bur Testing Gauge
WH-BTG
Bur Testing Gauge
Used to verify the condition of latch-type burs. Burs in proper condition will fit into larger diameter hole, but
will not fit into the smaller hole (marked red). Burs that fail either of these criteria are unfit for use, and may
cause damage to the handpiece if used.
16
ANCILLARY INSTRUMENTS
Surgical Driver
150-000
Surgical Driver
Used to drive implants into the osteotomy, particularly in the anterior region. The driver holds the Abutment-level
Driver, Ratchet which interfaces with the 3inOne Abutment. Also interfaces with the .050” (1.25mm) Hex Drivers
as well as Bone Taps and the Implant-level Drivers, Ratchet.
Extended Shank Drills
Tissue Punches
TSD4020
2.0mm Ext. Shank Starter Drill
PYTP
3.5mm Tissue Punch
TSD4025
2.5mm Ext. Shank Depth Drill
PGTP
4.5mm Tissue Punch
TSD4032
3.2mm Ext. Shank W.I. Drill
PBTP
5.7mm Tissue Punch
TSD4037
TSD4041
TSD4047
TSD4054
BioHorizons Tissue Punches are used in a latch-type
handpiece to remove the soft tissue from the crest of
the ridge prior to osteotomy preparation in a flapless
surgical procedure. Available in 3 platform diameters.
Extended Shank Drills are 8mm longer than our standard
drills. They have the same depth marks and cutting
geometry as our standard drills.
2.0mm Lindemann Bone Cutter
Clean-out Tap Tool
122-110
PXCT
Ø2.0mm Lindemann Bone Cutter
Implant Clean-out Tap Tool
Side-cutting drill used to correct eccentric
osteotomy preparations.
Used to re-thread implants where the internal threads
have become damaged. Requires a standard surgical
Ratchet (130-000) or Hand Wrench (300-400) as a
drive mechanism.
Bone Profiling Burs
PYBP
3.5mm Bone Profiling Bur & Guide
PGBP
PBBP
Used at implant uncovery to contour crestal bone to accommodate abutments when the implant is
subcrestal. For use in latch-type reduction handpieces. The Profiler’s internal geometry matches the
geometry of the included Profiler Guide. The Guide is screwed into the implant and then aligns the Profiler
for precise removal of tissue surrounding the platform. Comes in three sizes corresponding to the three
Tapered Internal prosthetic platforms.
17
SECTION 2: RESTORATIVE
Simple Solutions
Abutment Options
Prosthetic Instrumentation
18
SIMPLE SOLUTIONS KITS & COMPONENTS
Simple Solutions™
Simple Solutions restorative protocols on Tapered Internal implants allow clinicians to provide their patients with cement-retained
restorations in a minimal number of office visits. The pre-tapered abutments are designed to be restored without additional
preparation. After the impression has been made, patients can wear a tooth-colored Healing Cap over the abutment while
the laboratory fabricates the final prosthesis. Acrylic can be added to the Healing Cap as needed to help create a more natural
provisional. Please refer to the Simple Solutions Prosthetic Technique Manual (ref. ML0142) for detailed Instructions for Use.
1. Seat Simple
Solutions Abutment
2. Make closed-tray,
pick-up impression
3. Seat Final
Restoration
Internal Simple Solutions Healing Abutments
Prosthetic platform
0.8mm
collar
1.8mm
collar
2.8mm
collar
Internal 3.5mm Simple Solutions Healing Abutment
SPYHA08
SPYHA18
SPYHA28
SPGHA08
SPGHA18
SPGHA28
SPBHA08
SPBHA18
SPBHA28
Available in three collar heights to match each corresponding Simple Solutions Abutment (see page 21). Hand-tighten with a .050” (1.25mm) Hex Driver.
Titanium Alloy [Ti-6Al-4V].
19
Abutment
Screw
Simple Solutions
Abutment
Waxing Sleeve
for Bridge
Waxing Sleeve
for Crown
Healing Cap
Simple Solutions
Replica
Plastic
Impression
Cap
Simple Solutions Restorative Kits are available for the three Tapered Internal prosthetic platforms with two options for abutment height (4.0mm and
5.5mm), as well as three options for collar height (0.8mm, 1.8mm and 2.8mm). The kit provides the abutment, abutment screw, impression cap,
replica and laboratory waxing sleeves. The packaging is designed with three separate compartments that are opened as needed during the restorative
stages.
Prosthetic platform / Abutment height
0.8mm
collar
1.8mm
collar
2.8mm
collar
Internal 3.5mm Simple Solutions Kit, 4.0mm Height
K-PY4008
K - P Y 4 018
K-PY4028
K-PY5508
K - P Y 5 518
K-PY5528
K-PG4008
K - P G 4 018
K-PG4028
K-PG5508
K - P G 5 518
K-PG5528
K-PB4008
K - P B 4 018
K-PB4028
K-PB5508
K - P B 5 518
K-PB5528
Order by prosthetic platform, abutment height, and collar height.
20
Simple Solutions Abutments
0.8mm
collar
1.8mm
collar
2.8mm
collar
Internal 3.5mm Simple Solutions Abutment, 4.0mm
SPY4008
SPY4018
SPY4028
SPY5508
SPY5518
SPY5528
SPG4008
SPG4018
SPG4028
SPG5508
SPG5518
SPG5528
SPB4008
SPB4018
SPB4028
SPB5508
SPB5518
SPB5528
Prosthetic platform / Abutment height
Order by platform diameter, collar height and abutment height. Titanium Alloy [Ti-6Al-4V].
2.3°
4.6°
8.1°
Abutment
Height
Collar height
Assembly
Ø5.5mm
Ø4.5mm
Ø6.7mm
Simple Solutions Healing Caps
SYPHC40
Simple Solutions 3.5mm Healing Cap, 4.0mm
SYPHC55
SGPHC40
SGPHC55
SBPHC40
SBPHC55
Used as-is or as a coping for fabrication of provisional restorations (up to 30 days). Secure with temporary
cement. Order by platform diameter and abutment height. PEEK® (PolyEtherEtherKetone) Plastic.
21
Simple Solutions Impression Caps
SYPIC40
Simple Solutions 3.5mm Impression Cap, 4.0mm
SYPIC55
SGPIC40
SGPIC55
SBPIC40
SBPIC55
Order by platform diameter and abutment height.
Simple Solutions Replicas
SYR40
Simple Solutions 3.5mm Replica, 4.0mm
SYR55
SGR40
SGR55
SBR40
SBR55
Order by platform diameter and abutment height. Titanium Alloy [Ti-6Al-4V].
Simple Solutions Waxing Sleeves
SYPWSC
Simple Solutions 3.5mm Waxing Sleeve, Crown (single unit)
SGPWSC
SBPWSC
SYPWSB
Simple Solutions 3.5mm Waxing Sleeve, Bridge (multiple units)
SGPWSB
SBPWSB
Order by platform diameter. Trim for height. Burn-out plastic.
Simple Solutions Casting Reamers
SYCR
Simple Solutions 3.5mm Casting Reamer
SGCR
SBCR
Used to remove the snap feature from metal castings fabricated with Simple
Solutions Waxing Sleeves. Do not use on non-precious alloys. Order by
platform diameter.
22
INDIVIDUAL ABUTMENT SELECTION
Laboratory-milled, Custom Cast and Overdenture Abutment Selection
In addition to the Simple Solutions components shown earlier, a comprehensive selection of esthetic titanium, ceramic, custom castable and overdenture
abutments is available for Tapered Internal implants. The chart below shows the various abutment options, as well as their recommended uses. Please
refer to the BioHorizons Internal Prosthetic Technique Manual (ref. ML0118) for detailed Instructions for Use.
Cement-retained
Single- or Multiple-unit
Angled Esthetic
Abutments
page 26
3inOne
Abutments
page 25
Angled
Abutments
page 26
Screw-retained
Single-unit
Custom Castable (UCLA)
Abutments (Hexed)
page 29
Multiple-unit
Abutments (Non-hexed)
page 29
Esthetic
Abutments
page 27
Profile
Abutments
page 27
Narrow
Abutments
page 28
Ceramic
Abutments
page 28
Hybrid or Bar-retained
Implant-level
Cement- or Screwretained Provisional
Overdenture
Single- or Multiple-Unit
Abutments (Non-hexed)
page 29
Hybrid or Bar-retained
Abutment-level
PEEK Plastic Temporary
Abutments
page 25
Abutment-retained
Tissue-supported
Overdenture
Overdenture
Abutment for Screw
page 33
Locator Abutments
page 35
23
Ball Abutments
page 37
IMPRESSION COMPONENT SELECTION
Indirect and Direct Implant-level, Abutment-level and Overdenture Impression Components
Laboratory preparation/fabrication of the abutments shown on the facing page requires a working stone model be made from an intraoral impression
of the patient. The chart below shows the various component options used to make the impression, as well as their suggested uses. Please refer to the
BioHorizons Internal Prosthetic Technique Manual (ref. ML0118) for detailed Instructions for Use.
Single- or Multiple-unit Implant-level
Multiple-unit Implant-level (Non-hexed)
Cement or Screw-retained prostheses
Screw-retained prostheses
Direct Pick-up
Copings (Non-hexed)
page 32
Ball-top Screw used
with 3inOne Abutment
(Indirect, hexed)
page 31
Indirect Transfer
Copings
(Hexed)
page 31
Direct Pick-up
Copings (Hexed)
page 32
Implant Analogs
page 30
Implant Analogs
page 30
Multiple-unit Abutment-level
Hybrid or Bar-retained prostheses
Multiple-unit Ball Abutment Overdenture
Tissue-supported prostheses
Ball Abutments
(used as transfer coping)
page 37
Direct Pick-up Coping,
Abutment for Screw
page 34
Indirect Transfer Coping,
Abutment for Screw
page 34
Ball Abutment
Analogs
page 38
Analog, Abutment
for Screw
page 34
products shown not to scale
24
3inONE & TEMPORARY ABUTMENTS
3inOne Abutments for Cement-retained Restorations
PYREA
3.5mm 3inOne Abutment (Regular Emergence)
PGREA
PBREA
Packaged with each Tapered Internal implant with Abutment Screw. Also used with Ball-top Screw as a closed-tray, hexed-timed impression coping.
Ø3.7mm
Ø3.5mm
Ø3.9mm
5°
2°
8°
4mm
8mm
R
1.5mm
Ø4.2mm
Regular Emergence
Ø6.3mm
Ø5.3mm
PEEK Plastic Temporary Abutments
P Y R TA
3.5mm Plastic Temporary Abutment (Regular Emergence)
P G R TA
P B R TA
Packaged with Abutment Screw (PXAS). Hand-tighten with the .050” (1.25mm) Hex Driver. Easily modified for fabrication of cement- or screwretained provisional restorations (up to 30 days). A Direct Coping Screw (PXDCS, purchased separately) may be used to maintain screw access
hole during fabrication of screw-retained provisional prostheses. PEEK® (PolyEtherEtherKetone) Plastic.
Ø3.8mm
Ø3.2mm
Temporary Only
(Screw-retained or
Cement-retained)
5°
Ø4.3mm
5°
5°
5mm
8mm
1.5mm
R
Regular Emergence
Ø4.5mm
Ø5.5mm
25
Ø6.6mm
ANGLED ABUTMENTS
Angled Esthetic
Abutments
Cement-retained Restorations
Indirect
Transferfor
Copings
PYAEA
3.5mm Angled Esthetic Abutment (Wide Emergence)
PGAEA
4.5mm Angled Esthetic Abutment (Wide Emergence)
PBAEA
5.7mm Angled Esthetic Abutment (Regular Emergence)
Packaged with Abutment Screw (PXAS). Used to fabricate cement-retained, single- or multiple-unit prostheses. Titanium Alloy [Ti-6Al-4V].
15°
15°
15°
9mm
3mm
1mm
3.5mm /4.5mm - Wide Emergence
5.7mm - Regular Emergence
Ø5.6mm
Ø6.2mm
Ø7.0mm
Angled Abutments for Cement-retained Restorations
PYRAA
3.5mm Angled Abutment (Regular Emergence)
PGRAA
PBRAA
20°
20°
20°
10mm
R
Regular Emergence
5.7mm
4.6mm
3.8mm
Ø3.8mm
Ø4.6mm
26
Ø5.7mm
PROFILE ABUTMENTS
Esthetic Abutments for Cement-retained Restorations
PYSEA
3.5mm Straight Esthetic Abutment (Wide Emergence)
PGSEA
4.5mm Straight Esthetic Abutment (Wide Emergence)
PBSEA
5.7mm Straight Esthetic Abutment (Regular Emergence)
Ø3.7mm
Ø4.1mm
Ø3.9mm
9mm
3mm
1mm
3.5mm /4.5mm - Wide Emergence
5.7mm - Regular Emergence
Ø5.6mm
Ø6.2mm
Ø7.0mm
Profile Abutments for Cement-retained Restorations
PYWEA
3.5mm Wide Emergence Profile Abutment
PGWEA
4.5mm Wide Emergence Profile Abutment
Ø3.4mm
Ø3.8mm
5°
5°
10mm
W
Wide Emergence
Ø2.0mm
Ø5.5mm
27
Ø6.5mm
NARROW & CERAMIC ABUTMENTS
Narrow Abutments for Cement-retained Restorations
PYNEA
3.5mm Narrow Emergence Abutment
PGNEA
PBNEA
Ø3.0mm
Ø4.7mm
Ø3.5mm
2.4°
5°
5°
10mm
Ø4.2mm
N
Narrow Emergence
Ø4.5mm
Ø3.5mm
Ø5.7mm
Ceramic Abutments for Cement-retained Restorations
PGRCA
4.5mm Ceramic Abutment (Regular Emergence)
PBRCA
5.7mm Ceramic Abutment (Regular Emergence)
Not available in all markets. Call for availability.
Packaged with Abutment Screw (PXAS). Used to fabricate cement-retained, single- or multiple-unit prostheses. Yttria-stabilized Zirconia.
Ø3.5mm
Ø3.9mm
8°
5°
10mm
R
Regular Emergence
2.1mm
Ø5.5mm
28
Ø6.6mm
CUSTOM CASTABLE ABUTMENTS
Custom Castable (UCLA) Abutments - Hexed
P YC A H
3.5mm Custom Cast Abutment, Hexed
PGCAH
PBCAH
Indicated for single-unit screw-retained or custom abutment cement-retained restorations. All two-piece abutments are packaged with the
Abutment Screw (PXAS). Gold Alloy base with Delrin® sleeve.
Ø4.1mm
Ø5.7mm
Ø4.5mm
10mm
10.5mm
3.6mm (top of alloy coping)
0.75mm
Ø3.5mm
Ø4.5mm
Ø5.7mm
Custom Castable (UCLA) Abutments - Non-hexed
PYC AN
3.5mm Custom Cast Abutment, Non-hexed
PGCAN
PBCAN
Indicated for multiple-unit, screw-retained restorations. All two-piece abutments are packaged with the Abutment Screw (PXAS). Gold Alloy base with
Delrin® sleeve.
Ø4.1mm
Ø5.7mm
Ø4.5mm
10mm
10.5mm
3.6mm (top of alloy coping)
0.75mm
Ø3.5mm
Ø4.5mm
29
Ø5.7mm
IMPLANT ANALOGS & SCREWS
Implant Analogs
PYIA
3.5mm Implant Analog
PGIA
PBIA
Represents the Tapered Internal implant in a laboratoryfabricated, implant-level stone model. Not intended for use
with Simple Solutions components. Titanium Alloy [Ti-6Al-4V].
Abutment Screw
PXAS
Abutment Screw
Fits all prosthetic platforms. Low profile screw head. Packaged with all two-piece
abutments. Utilizes the .050” (1.25mm) Hex Driver. Final torque: 30 Ncm.
Direct Coping Screw
PXDCS
Direct Coping Screw
Fits all prosthetic platforms. Packaged with all Direct Pick-up Copings. May also be used
in place of the Abutment Screw (PXAS) when extra length is needed, or to maintain the
screw access hole during fabrication of screw-retained provisional prostheses.
Utilizes the .050” (1.25mm) Hex Driver. Hand-tighten or torque to 30Ncm depending on
application. Titanium Alloy [Ti-6Al-4V].
30
INDIRECT TRANSFER COPINGS
Indirect Transfer Copings (Closed Tray) - Hexed
PYNIC
3.5mm Narrow Indirect Transfer Coping
PYRIC
3.5mm Regular Indirect Transfer Coping
PYWIC
3.5mm Wide Indirect Transfer Coping
PGNIC
PGRIC
PGWIC
4.5mm Wide Indirect Transfer Coping
PBNIC
PBRIC
Used to make a closed-tray, implant-level, hexed-timed impression. Packaged with
the Abutment Screw (PXAS). Titanium Alloy [Ti-6Al-4V].
Ball-top Screw for Indirect Transfer
PXBT
Ball-top Screw
Fits all prosthetic platforms. Used with the 3inOne Abutment to form an impression
coping for closed-tray, hexed-timed transfers. May be used to increase height of
Indirect Transfer Copings by 3mm. Hand-tighten. Titanium Alloy [Ti-6Al-4V].
Ø3.8mm
Indirect Transfer Copings
are packaged with the
Abutment Screw (PXAS)
3mm
11mm
8mm
3mm
The Ball-top Screw
MUST be used with a
3inOne Abutment or an
Indirect Transfer Coping
Narrow
Emergence
Regular
Emergence
31
Regular
Emergence
Wide
Emergence
DIRECT PICK-UP COPINGS
Direct Pick-up Copings (Open Tray) - Hexed
PYNDC
3.5mm Narrow Direct Pick-up Coping, Hexed
PYRDC
3.5mm Regular Direct Pick-up Coping, Hexed
PYWDC
3.5mm Wide Direct Pick-up Coping, Hexed
PGNDC
PGRDC
PGWDC
4.5mm Wide Direct Pick-up Coping, Hexed
PBNDC
PBRDC
Used to make an open-tray, implant-level, hexed-timed impression. Packaged with the
extended Direct Coping Screw (PXDCS). Titanium Alloy [Ti-6Al-4V].
Direct Pick-up Copings (Open Tray) - Non-hexed
PYNDCN
3.5mm Narrow Direct Pick-up Coping, Non-hexed
PGNDCN
PBNDCN
Used to make an open-tray, implant-level, non-hexed impression. Packaged with the
extended Direct Coping Screw (PXDCS). Titanium Alloy [Ti-6Al-4V].
8.5mm
17.5mm
9mm
5mm
Narrow
Emergence
(Non-hexed)
Narrow
Emergence
(Hexed)
32
Regular
Emergence
Wide
Emergence
ABUTMENT FOR SCREW
Abutment for Screw
PYAFS1
3.5mm Abutment for Screw, 1mm collar
PYAFS3
PYAFS5
PGAFS1
PGAFS3
PGAFS5
PBAFS1
PBAFS3
Indicated for multiple-unit restorations including: screw-retained restorations at the abutment level, cast alloy bars for overdentures and
fixed/detachable (hybrid) restorations. Comes packaged with the Cover Cap (PXABCC). Titanium Alloy [Ti-6Al-4V].
PXABCC (2.7mm high)
Ø4.25mm
Ø4.25mm
Ø4.25mm
1mm
12mm
1, 3 or 5mm
N
Narrow Emergence
Ø4.25mm
Ø4.5mm
Ø5.7mm
Gold Coping, Abutment for Screw
Ø4.25mm
Ø4.25mm
PXABGC
PXABPC
Plastic Coping, Abutment for Screw
PXABGC
PXABPC
Gold Coping, Abutment for Screw
Plastic Coping, Abutment for Screw
May be trimmed for height. Packaged with the
Screw (regular), Abutment for Screw (PXABS). Gold
Alloy base with Delrin® sleeve.
May be trimmed for height. Packaged with the
Screw (regular), Abutment for Screw (PXABS).
Delrin® sleeve.
Cover Cap, Abutment for Screw
Screw (regular), Abutment for Screw
PXABS
PXABCC
Screw (regular), Abutment for Screw (5 pack)
Cover Cap, Abutment for Screw
Used to retain bars or prostheses fabricated with
the Abutment for Screw Copings. Utilizes the
.050” (1.25mm) Hex Driver. Final torque: 30 Ncm.
Packaged with all Abutments for Screw. Handtighten with .050” (1.25mm) Hex Driver. Titanium
Alloy [Ti-6Al-4V].
33
ABUTMENT FOR SCREW COMPONENTS
Direct Pick-up Coping, Abutment for Screw
PXABDC
Direct Pick-up Coping, Abutment for Screw
Used to make a direct pick-up impression (open-tray) at the
abutment level. Packaged with the Screw (long), Abutment for
Screw (PXABSL). Used only with Abutment for Screw. Titanium
Alloy [Ti-6Al-4V].
Indirect Transfer Coping, Abutment for Screw
PXABIC
Indirect Transfer Coping, Abutment for Screw
Used to make an indirect transfer (closed-tray) impression at the
abutment level. Used only with Abutment for Screw. Titanium
Alloy [Ti-6Al-4V].
Analog, Abutment for Screw
PXABA
Analog, Abutment for Screw
Used to represent the Abutment for Screw/Implant assembly
in the working cast. Not for use with implant-level impressions.
Screw (long), Abutment for Screw
PXABSL
Screw (long), Abutment for Screw (5 pack)
Used in the lab when a longer screw is desired. Used only with the
Abutment for Screw. Hand-tighten or torque to 30Ncm depending
on application. Titanium Alloy [Ti-6Al-4V].
Hex Adapter, Abutment for Screw
PXHA
Required for placement of Abutment for Screw. May be driven by either Hand
Wrench, Torque Wrench or AS123 Hand Unit.
34
LOCATOR® ABUTMENTS
N
3.5
N
4.5
N
5.7
PYLA0
PYLA1
PYLA2
PYLA3
PYLA4
PYLA5
PYLA6
3.5mm Locator Abutment, 0mm Cuff Height
PGLA0
PGLA1
PGLA2
PGLA3
PGLA4
PGLA5
PGLA6
4.5mm Locator Abutment, 0mm Cuff Height
PBLA1
PBLA2
PBLA3
PBLA4
PBLA5
PBLA6
5.7mm Locator Abutment, 1.0mm Cuff Height
Order by Cuff Height to match the height of the gingival tissue. The female portion of the abutment adds 1.5mm to the stated height (see below).
The abutment needs to extend above the tissue by 1.5mm to allow the Locator Male to seat completely. Order one Locator Male Processing Set
for each Locator Abutment (sold in packs of 2 or 10: LMPP-2 or LMPP-10).
The Male Processing Package provides 3 choices of retention (see opposite page). The Replacement Males (clear, pink and blue) are used to
restore implants with up to 10° of divergence (20° between implants). The Extended Range Replacement Males (green and red) accommodate
divergences from 10° and 20° (40° between implants), and may be purchased separately.
Locator Abutments are made from Titanium Alloy [Ti-6Al-4V].
Ø5.5mm
Ø3.5mm
2.5mm
N
Ø3.5mm
Ø3.5mm
1.5mm
Order by stated
height in millimeters:
0mm to 6mm
Cutaway view of Denture
Cap and Male Nylon
Insert
Narrow Emergence
Ø3.5mm
Ø4.5mm
Locator is a registered trademark of Zest Anchors, Inc.
35
Ø5.7mm
LOCATOR COMPONENTS
LCT
Locator Core Tool
Multi-purpose tool serves as hand driver for seating Locator Abutments onto
the implants, seating tool for nylon male inserts and insert removal tool.
LMPP-2
Locator Male Processing Package (2 pack)
Includes: (1) Denture Cap with (1) Black Processing Male; (1) White Block-out
Spacer; (1) Clear, (1) Pink and (1) Blue Nylon Males.
LMPP-10
Locator Male Processing Package (10 pack)
Includes: (1) Denture Cap with (1) Black Processing Male; (1) White Block-out
Spacer; (1) Clear, (1) Pink and (1) Blue Nylon Males.
LIC
Locator Impression Coping (4 pack)
LFA-4MM
Locator Female Analog Ø4mm (4 pack)
LFA-5MM
Locator Female Analog Ø5mm (4 pack)
LRM-C
Locator Replacement Male (clear) (4 pack)
Retention: 5lb / 2268g
LRM-P
Locator Light Retention Replacement Male (pink) (4 pack)
Retention: 3lb / 1361g
LRM-B
Locator Extra Light Retention Replacement Male (blue) (4 pack)
Retention: 1.5lb / 680g
LRM-G
Locator Extended Range Replacement Male (green) (4 pack)
LRM-R
Locator Extended Range Extra Light Retention Rep. Male (red) (4 pack)
LPP
Locator Parallel Post (4 pack)
LBPRM
Locator Black Processing Replacement Male (4 pack)
LAMG
Locator Angle Measurement Guide
LSDT-15MM
Locator Square Drive Tool (15mm)
Used with a torque wrench to seat Locator Abutments. 15mm in length.
LSDT-21MM
Locator Square Drive Tool (21mm)
Used with a torque wrench to seat Locator Abutments. 21mm in length.
36
BALL ABUTMENTS / O-RINGS
Ball Abutments
PYBA1
3.5mm Ball Abutment, 1mm Collar
PYBA3
PYBA5
PGBA1
PGBA3
PGBA5
PBBA1
PBBA3
Ball Abutments are indicated for retention of tissue-supported overdentures. They are recommended for relatively parallel implants. See below
and on the facing page for attachment options. Ball Abutments may be used as indirect transfer copings for production of a working cast.
Ø2.5mm
Ø2.5mm
Ø2.5mm
Ø5.5mm
Ø5.9mm
3.2mm
3.5mm
2.6mm
5mm
1, 3 or 5mm
N
Ø3.5mm
Ø4.5mm
Ø5.7mm
Narrow Emergence
O-Ring Attachment System
Standard O-ring attachment.
260-100
O-Ring Attachment Set
O-Ring encapsulator
2 Processing O-rings
2 Clinical O-rings
37
260-210
Clinical O-Ring
Used for clinical applications.
Silicone. 12 per package.
260-220
Processing O-Ring
Used for lab processing
applications. Buna. 12 per package.
260-300
O-Ring Encapsulator
Female receptacle processed into
denture. Titanium. 2 per package.
BALL ABUTMENT COMPONENTS
Ball Attachment System
The Ball Attachment system offers several advantages over traditional O-ring attachments. It requires less mesial/distal/buccal/lingual space and offers
four (4) different levels of retention. The retention inserts can be easily changed chairside.
BCAS
BCAHT
Ball Attachment Set
Includes: (1) Titanium Housing, (3) Female Nylon Inserts - white (more retention),
pink (less retention), black (lab processing) and (1) Protective Disk (tissue protector
for impression taking and chair-side denture pick-up)
Attachment Housings – Titanium BCCBP
Castable Ball Pattern
Burn-out component used by the lab
for fabrication of a custom bar with
ball attachments. 2 balls per pattern.
BCIST
Insert Seating Tool
Used to seat nylon inserts in
attachment housings.
BCR
Reamer
Used to adjust retention of nylon inserts.
For Resin pickup or Soldering. 2 per package.
BCIB
Black Nylon Insert
Lab Processing and Chair-side Denture
Pick-up. 2 per package.
BCIG
Green Nylon Insert
Clinical use. 2 per package.
Elastic Retention.
BCIY
Yellow Nylon Insert
Extra Soft Retention: 1.4lb / 525g
BCIP
Pink Nylon Insert
Soft Retention: 2.3lb / 875g
BCIW
White Nylon Insert Clinical use. 2 per package.
Standard Retention: 3.3lb / 1250g
BCPT
Paralleling Tool
A laboratory tool used on a surveyor to
position and wax castable balls on a bar.
BCDR
Directional Rings
Used for obtaining parallelism.
0°, 7° and 14° rings. Set of 3.
BCS
Set of 3 tools
Insert Seating Tool, Reamer and Paralleling Tool.
Ball Abutment Analogs
3.5
4.5
5.7
PYGBAA
3.5/4.5mm Ball Abutment Analog
PBBAA
5.7mm Ball Abutment Analog
Used to represent the Ball Abutment/Implant assembly in the
working cast. Only used in conjunction with Ball Abutments.
38
PROSTHETIC INSTRUMENTATION
Prosthetic Instrumentation System
320-000
Complete Prosthetic Instrumentation System
Includes: AS123 Hand Unit / Hand Wrench / 30 Ncm
Torque Wrench / .050” (1.25mm) Hex Driver, Regular/
.050” (1.25mm) Hex Driver, Long / Hex Adapters for
Abutment for Screw / Ratchet Extender / Sterilization Tray.
300-070
Prosthetic Sterilization Tray
Autoclavable tray for prosthetic instrumentation
(included with the 320-000).
300-100
AS123 Hand Unit
Provides improved vision and easy access to prosthetic
components in posterior regions of the mouth. Hand
Wrench and Drivers must be purchased separately.
May also be purchased as part of the 320-000 Complete
Prosthetic Instrumentation System (see above).
6.25mm
12.5mm
300-430
30 Ncm Torque Wrench
Used to deliver torque to prosthetic components.
300-350 regular
.050” (1.25mm) Hex Driver Regular and Long
Used to drive all surgical and prosthetic components
with the exception of the Abutment for Screw.
300-351 long
PXHA
Required for placement of Abutment for Screw. May
be driven by either Hand Wrench, Torque Wrench or
AS123 Hand Unit.
300-400
Hand Wrench
Used on drive end of AS123 Hand Unit .
Also fits individual Hex Drivers/Adapters and Bone Taps.
products shown not to scale.
39
PROSTHETIC INSTRUMENTATION
Abutment Clamp
Used to apply counter-torque during the delivery and tightening of the Abutment Screw, shielding the bone / implant interface from potentially
damaging stresses.
IMPAH
Abutment Clamp
Implant Analog Handles
Used to hold abutments for chairside or laboratory preparation, these handles mimic the implant/analog hex geometry. Abutments are secured to the
handle with the standard Abutment Screw (PXAS). Comes in two platform sizes: Ø3.5/4.5mm and Ø5.7mm.
PYGAH
Ø3.5/4.5mm Platform Analog Handle
PBAH
Ø5.7mm Platform Analog Handle
40
PATIENT EDUCATION MATERIALS
TI4XIM
Tapered Internal 4x Patient Education Model
This 4-times scale model includes the Implant, Abutment, Abutment Screw, Ball-top
Screw, Healing Abutment, Cover Cap, Implant Driver and Hex Driver. Excellent for
demonstrating implant components to the patient.
Call for availability.
ML0131
Patient Education – Dental Implants - the tooth replacement solution
This high-quality flipbook helps the implant candidate understand the rationale and
the advantages of implant therapy compared to traditional treatment methods. The
message focuses on the positives of implants and their ability to stop the bone loss
associated with edentulism. Many treatment options are detailed to aid the clinician in
describing a procedure. 9” x 6” (23cm x 16cm).
ML0128
Patient Education – Tooth Replacement with Dental Implants poster
This 2-sided laminated poster visually outlines the advantages of implant therapy
compared to traditional treatment methods. One side focuses on tooth replacement
options, while the opposite side contains information on bone loss and how dental
implants can help preserve bone. 24” x 36” (61cm x 91cm).
ML0103
Patient Education – If you have missing teeth...
This four-fold brochure helps the implant candidate understand the rationale and
the advantages of implant therapy compared to traditional treatment methods. The
message focuses on the positives of implants and their ability to stop the bone loss
associated with edentulism. 8.5” x 3.5” (21.5cm x 8.7cm).
ML0129
Patient Education – Rebuilding and maintaining bone
This brochure explains the benefits and basic science of bone regeneration and its
relationship to implant therapy. 8.5” x 3.5” (21.5cm x 8.7cm).
ML0114
Patient Education – Secure dentures bring back your smile
This brochure helps the denture wearer understand the rationale and the advantages
of denture stabilization with implants. 8.5” x 3.5” (21.5cm x 8.7cm).
41
REFERENCES
1. Heat production by 3 implant drill systems after repeated drilling and sterilization.
Chacon GE, Bower DL, Larsen PE, McGlumphy EA, Beck FM.
J Oral Maxillofac Surg. 2006 Feb;64(2):265-9
2. Cell Interaction with Microtextured Surfaces
JL Ricci, R Rose, JK Charvet, H Alexander, CS Naiman.
Presented at the Fifth World Biomaterials Congress. May 29-June 2, 1996. Toronto, Canada.
3. Interactions between MC3T3-E1 cells and textured Ti6Al4V surfaces
Soboyejo WO, Nemetski B, Allameh S, Marcantonio N, Mercer C, Ricci J.
J Biomed Mater Res. 2002 Oct; 62(1):56-72.
4. Cytoskeletal Organization in Three Fibroblast Variants Cultured on Micropatterned Surfaces
JC Grew, JL Ricci.
Presented at the Sixth World Biomaterials Congress. Kamuela, HI. May 15-20, 2000.
5. Tissue Response to Transcutaneous Laser Microtextured Implants
CL Ware, JL Simon, JL Ricci.
Presented at the 28th Annual Meeting of the Society for Biomaterials. April 24-27, 2002. Tampa, FL.
6. Osseointegration on metallic implant surfaces: effects of microgeometry and growth factor treatment
Frenkel SR, Simon J, Alexander H, Dennis M, Ricci JL.
J Biomed Mater Res. 2002;63(6):706-13.
7. The Effects of Laser Microtextured Collars Upon Crestal Bone Levels of Dental Implants
JL Simon, J Heair, Y. Khanna, D. Ehrenberg, J Ricci, B Zweig, S. Weiner.
Presented at the 29th Annual Meeting of the Society for Biomaterials, Reno, NV.
Submitted for publication.
8. The Influence of Different Neck Designs on Marginal Bone Tissue
Hanna Eun Kyong Bae, Dong Hoo Han.
Yonsei University, Graduate School, Department of Dental Science.
Submitted for publication.
9. Clinical Evaluation of Laser Microtexturing for Soft Tissue and Bone Attachment to Dental Implants
GE Pecora, R Ceccarelli, M. Bonelli, H. Alexander, JL Ricci.
Best Clinical Innovations Presentation Award. Academy of Osseointegration 2004 Annual Meeting.
Submitted for Publication.
10. Histologic Evaluation of 3 Retrieved Immediately Loaded Implants After a 4-Month Period
I Giovanna, G Pecora, A Scarano, V Perrotti, A Piattelli.
Implant Dentistry. Vol 15, Number 3, 2006.
42
BioHorizons USA
BioHorizons Canada
2300 Riverchase Center
Birmingham, AL 35244
21 Amber Street, Unit # 7
Markham, Ontario L3R 4Z3
Customer Care / Servicio al Cliente:
888-246-8338 or 205-967-7880
Customer Care / Service à la Clientèle:
866-468-8338 or / ou 905-944-1700
BioHorizons Spain
BioHorizons UK
Bocángel, 38
28028 Madrid, España
180 Dukes Ride
Crowthorne, Berkshire RG45 6DS
Atención al Cliente: +34 91 713 10 84
Customer Care:
+44 8700 620 550
BioHorizons Germany
BioHorizons Australia
Kunden Service:
+49 7661-909989-0
Customer Service:
+61 2 8399 1520
Marktplatz 3
79199 Kirchzarten
BioHorizons Mexico
Kelvin 8 Int. 303
Col. Anzures
C.P. 11590, Mexico, D.F.
Servicio al Cliente:
+52 55 5545 1297
25-33 Allen Street
Waterloo NSW 2012
BioHorizons Chile
Juan Esteban Montero 5944
Las Condes
Santiago, Chile
Atención al Cliente: +56 2 475 7230
BioHorizons products are cleared for sale in the European Union under the EU Medical Device Directive 93/42/EEC. We are proud to be registered to ISO
13485:2003, the international quality management system standard for medical devices, which supports and maintains our product licences with Health Canada and
in other markets around the globe.
© 2007 BioHorizons Implant Systems, Inc. All Rights Reserved. ML0603 REV A OCT 2007
w w w . b i o h o r i z o n s . c o m

Tapered Internal Product Catalog

Transcription

Similar documents

drill sequence

Dash led conversion P1 This is a continuation of a

minute - Meridian

Back Cover

Natural Finishes - Kingspan Access Floors

Simple Solutions Prosthetic Technique Manual

bis tristar - LUCKINSlive

- Serpent

prosthetics catalog

① Entry Record Data Locator