2007-14 Jeep Wrangler JK Products

2007-14 Jeep Wrangler JK products
NEW! Our latest product for the JK’s, LitePANELs. These ABS plastic molded panels are
designed to fit perfectly on the curves of the stock JK sheetmetal. The LitePANELs allow
the ORO LiteDOT LED taillights to fit directly onto the JK, no body modifications necessary.
The LitePANELs are retained by the LiteDOT mounting hardware, using a stainless bracket
to clamp the assembly to the body. Included with this kit is the ORO LiteBOX kit, which
will allow the retention of the factory turn signal bulb, thereby eliminating fast flash or
bulb out warnings. LitePANELs are finished as matte black and textured to match the
other Wrangler parts, but can also be painted to match the body. *ORO LiteDOTs sold
separately.
Part Number LD-LP LitePANELs
$149
LiteDOTs LED taillights. These are to be used with the LitePANELs above, but can be
mounted on any flat surface. Designed to be direct fit on 1987-2006 Wranglers, these can
be adapted to nearly any configuration. Many manufacturers offer replacement quarter
panels for JKs that accept the LiteDOTs as well. These measure 5” in diameter and are
mounted with 2 thru bolts thru the face. Black polycarbonate housing with UV compliant
resin filled front and backside. Provides tail, turn/stop, and reverse functions along with
sidelights.
Part Number LD-RRW2 LED taillights Pair
$199
1
2014 OffRoadOnly Product Guide (Wrangler JK products continued)
NEW! Hop-Stopper is OffRoadOnlys solution to the Wrangelr JK hood flutter. This part is
manufactured of stainless steel and assembles below the steel tube structure of the grill that
the hood hook catches on when the hood is opened. When the hood is closed, the hood hook
passes thru the Hop-Stopper and then simply pushing the lever to the closed position, the hood
hook is retained solidly below the grille tube structure and the hood is now 100% retained, no
movement at all! The Hop-Stopper is engaged by reaching thru the middle grill slot, but it is
mounted high enough that you can’t see it from the front of the vehicle, you need to reach in
and feel it to know its there.
Part Number HS-JK Hop-Stopper
$59
NEW! LiteBOX is the one solution for the Wrangle JK Fast flash that will always work. The
process is simple, retain the factory turn signal bulb in the system. These boxes are lazer cut
to accept the turn signal bulb housing for the stock JK taillight. Simply unplug the bulb from
the OEM taillight, wire in the LEDs to the harness and then stick the bulb in these boxes and
mount them inside the fender wells. This allows the bulb to flash and keep the computer
happy. The LiteBOXs hold the bulb in place, keeping wires and other plastic away from the hot
bulb itself. Kit comes with mounting screws as well as slide on tabs to mount the edge to a
sheet metal edge with no drilling. Boxes are approximately 3 ½” on edge.
Part Number LS-LB LiteBOX
$29
LiteSPOTs LED spotlights were designed to be a low profile under chassis light, a rock light.
The LiteSPOTs are 3 high power white LEDs embedded in a clear resin housing to deliver a
water and corrosion proof package that delivers a wide beam of bright light, with a 4-6 foot
focal range. They are not designed as backup or driving lamps. The LiteSPOTs include a
neodymium magnet encased in the resin, providing for easy ‘stick on’ mounting to any
ferrous surface. There is also a thru hole drilled in each one and a supplied self tapping
screw to allow for installation on non-ferrous surfaces. Each LiteSPOT measures 1 3/8” in
diameter and 5/8” thick. Each LiteSPOT comes with 24” of 2 strand 22 guage wire attached
and each until will draw approximately 120 milliamps. LiteSPOTs are sold individually, as
pairs or as our pre-packaged “chassis kit” which includes 6 LiteSPOTs and all the wire,
switch and connectors to wire these 6 under a vehicle. Also work well in pickup boxes to
light up under tonneau covers and truck caps. High heat resistant, can be used under hood
or inside as dome lights.
Part Number LS-W1 Single LiteSPOT
$29
Part Number LS-W2 Pair of LiteSPOTs
$54
Part Number LS-W6 Chassis kit LiteSPOT
$169
2
2014 OffRoadOnly Product Guide (Wrangler JK products continued)
LItePLATE LED License plate lights are the easiest way to light up your license plate. The
stainless bracket is designed to be mounted behind the license plate, retained by 2 of the
license plate mounting bolts passing thru the large holes which measure 7” from center to
center. The stainless bracket then hangs a polycarbonate black housing containing 3
license palte facing white LEDs to light up the license plate. The rearward face of the black
housing contains 3 red LEDs that can be hooked up to operate as a 3rd brake light or a
clearance light. Offered in 3 versions, the difference is the length of the wire harness and
whether is has a disconnect in it. The disconnect (LD-PL6) version is designed for use with
the Rockhard 4x4 parts License Plate relocation kit. (Rockhard part number RH-4007,
available seperately) and backside.
Part Number LD-PL1 LitePLATE with 1 foot harness
$30
Part Number LD-PL6 LitePLATE with 6 foot harness and disconnect $45
Part Number LD-PL7 LitePLATE with 7 foot harness, no disconnect $45
3
2014 OffRoadOnly Product Guide (Wrangler JK products continued)
Tru-Turn is our Wrangler JK tie rod upgrade. The factory tie rod has many curves in it and
curves make tie rods weaker. The Tru-Turn kit utilizes the same bolt on hub bracket design
that has been proven in the ORO U-Turn steering kit for TJ’s. By bolting the hub brackets
to the steering knuckles, there is a new mounting point for the tie rod to the steering
knuckle. This generates the ability to have a straight tie rod that goes from one side to the
other, making it as strong as possible as well as easy to adjust toe. The Tie rod is
constructed of 1 3/8” solid heat treated chromoly, drilled and tapped for the ¾ ton
application tie rod ends. Includes everything you need to bolt this onto the JK Dana 30 or
Dana 44 front axle. There is not a provision for the steering stabilizer included, we offer a
stabilizer relocation kit or a separate mounting tab for the stabilizer as an option. These
tie rod ends are greaseable and replacements are available at your local auto parts store.
Customer report the greatest benefit of this steering upgrade is the reduced (actually
eliminated) wandering feeling typicaly found with the 4 door Wranglers.
Part Number TT-SK Tru-Turn Steering Kit
$425
Tru-Turn Steering Stabilizer relocation kit for Wrangler JKs moves the steering stabilizer
from below the tie rod up to run along the draglink and attach to the frame at the
driverside. The welded bracket with the ears mounts between the factory swaybar mount
and the frame with the moving end clamped to the draglink with our steering stabilizer
bracket kit as shown below. This kit includes all the parts to mount a standard 8” eye to
eye steering stabilizer in this location, but does not include the stabilizer. There is a spacer
plate included to space the passenger side of the swaybar mount down an equal amount
as the driverside for when a swaybar like our SwayLOC is used.
Part Number TT-SSRK Tru-Turn Stabilizer Relocation kit
$119
Steering Stabilzer Bracket Kit This bracket kit includes u-bolts and a bracket to fit over 1
¼’ and 1 3/8” round stock. The 5th hole in the bracket accepts a ½” bolt to bolt the moving
end of a standard steering stabilizer to.
Part Number UT-SK Stabilizer bracket kit
$25
4
2014 OffRoadOnly Product Guide (Wrangler JK products continued)
SwayLOC is the most unique antisway bar for Jeeps. The premise of the SwayLOC is the
Dual Rate design. This design encompases 2 individual torsion bars and a simple method
for engagement. When both bars are used, or the arms are latched together in engaged
mode, there is maximum anti-roll control as the force is controlled by both the outer
hollow torsion bar as well as the inner solid torsion bar. When the latch is moved to the
open position, the two latching arms are allowed to move independently and now the
body roll is controlled by a softer rate torsion bar. This soft bar allows the axle to travel
thru full range of motion while giving a slight amount of roll control to match the rear
antisway bar and balancing the front suspension to the rear. The latching mechanism is
either a simple manual ‘flip a lever” control, where a spring being pulled over center to
move the latch, or an even simpler air cylinder that opens and closes the latch, similar
to an ARB operation. An air supply of at least 50psi, maximum 120psi is required for the
air control option. Compressed air will work with proper regulation. Very little volume
of air is used in the movement of the cylinder. Each kit comes with the necessary
hardware to fit a wide range of lift heights. SwayLOCs are designed to bolt onto stock
applications, custom or modified track bar brackets or other items in the area the
SwayLOC moves may require modification.
Part Number SL-JK-LV SwayLOC JK Manual Flip a Lever
$799
Part Number SL-JK-RC SwayLOC JK Remote control air
$999
5
2014 OffRoadOnly Product Guide (Wrangler JK products continued)
York Compressor Bracket Kit 2007-11 JK 3.8L This bracket kit is designed to mount a York
heavy duty compressor with a 6 rib clutch to the 3.8L engine. The kit includes the bracket
and hardware to mount the compressor as well as the belt and idler pulleys necessary to
complete the install. With this kit the compressor will be mounted to the engine with the
clutch pulley between the crankshaft and the A/C compressor. The body of the York will
be positioned to the radiator side of the belt. Loosening the mounting of the york and
pivoting it away from the engine is required to change the belt. *York compressor and clutch
not included, but available seperately.
Part Number AK-YBKJK07 York bracket kit JK 2007-11 3.8L
$239
York Compressor Bracket Kit 2012-14 JK 3.6L This bracket kit is designed to mount a York
heavy duty compressor to the front of the 3.6L engine. There is no belt in this kit as this kit
does not require modification to the belt. This kit does include the clutch for a
standard/heavy duty york and that clutch is modified to accept our unique york direct drive
clutch adaptor. The york will mount with the clutch on centerline of the engines crankshaft
and the direct drive coupler on the clutch will engage into the harmonic balancer in a lovejoy style. Brackets and hardware are included to mount the compressor in this location.
*York compressor is not included, but available seperately.
Part Number AK-YBKJK12 York bracket kit JK 2012-14 3.6L
$529
Complete York Air Supply Kit 2007-11 JK 3.8L This kit is a complete kit, everything needed
to install the york compressor onto this application. Included are all the high quality,
proven air supply parts that we feel is necessary for the best, most reliable york air supply
system, along with the bracket kit shown above. Complete installation of this kit will result
in an air supply that generates a tank pressure maximum of 200 psi, and comes with all
the brackets, wire harness and instructions to plumb and operate the system as it was
designed. There is a pair of Milton M Style quick couplers included and our
recommendation is to install them inside the vehicle to keep them clean and coorsion free.
Stainless brackets included in the kit to mount these. This kit includes the Norgren heavy
duty oil removal filter with the automatic drain to return the oil back to the compressor
crankcase.
Part Number AK-JK07 York Air Supply kit for 2007-11 JK
$1699
Complete York Air Supply Kit 2012-14 3.6L This kit is a complete kit, everything needed to
install the york compressor onto this application. Included are all the high quality, proven
air supply parts that we feel is necessary for the best, most reliable york air supply system,
along with the bracket kit shown above.. Complete installation of this kit will result in an
air supply that generates a tank pressure maximum of 200 psi, and comes with all the
brackets, wire harness and instructions to plumb and operate the system as it was
designed. There is a pair of Milton M Style quick couplers included and our
recommendation is to install them inside the vehicle to keep them clean and coorsion free.
Stainless brackets included in the kit to mount these. This kit includes the Norgren heavy
duty oil removal filter with the automatic drain to return the oil back to the compressor
crankcase.
Part Number AK-JK12 York Air Supply kit for 2012-14 JK
$1879
6
2014 OffRoadOnly Product Guide (Wrangler JK products continued)
AiROCK Air suspension 2007-11 Wrangler JK 2007-11 The AiROCK air suspension kit is our
flagship product. Leading the offroad (and onroad) category by providing a one button user
adjustable suspension that allows the operator to adapt the vehicle best to changing
offroad conditions as well as a completely automated Active Air Management system for
on road driving when vehicle speed exceeds 30 mph. This kit contains all the components
to install into this model Wrangler JK. Not included is an air supply, of which the Complete
York Air Supply Kit is recommended. Additional required items once that Complete Air
Suply kit is included are the Air Filter regulator kit. This AiROCK kit does include the shocks,
custom manufactured for ORO by Radflo. Contact ORO for more details.
Part Number AR-JK07 AiROCK Air Suspension Kit for 2007-11 JK
$5495
AiROCK Air suspension 2012-14 Wrangler JK 2012-14 The AiROCK air suspension kit is our flagship
product. Leading the offroad (and onroad) category by providing a one button user adjustable
suspension that allows the operator to adapt the vehicle best to changing offroad conditions as well
as a completely automated Active Air Management system for on road driving when vehicle speed
exceeds 30 mph. This kit contains all the components to install into this model Wrangler JK. Not
included is an air supply, of which the Complete York Air Supply Kit is recommended. Additional
required items once that Complete Air Suply kit is included are the Air Filter regulator kit. This
AiROCK kit does include the shocks, custom manufactured for ORO by Radflo. Contact ORO for more
details.
Part Number AR-JK12 AiROCK Air Suspension Kit for 2012-14 JK
$5495
7
1997-2006 Jeep Wrangler TJ products
LiteDOTs LED taillights. Designed to be direct fit on 1987-2006 Wranglers, these can be
adapted to nearly any configuration with a flat mounting surface. Many manufacturers
offer replacement quarter panels for TJs that accept the LiteDOTs as well. These measure
5” in diameter and are mounted with 2 thru bolts thru the face. Black polycarbonate
housing with UV compliant resin filled front and backside. Provides tail, turn/stop, and
reverse functions along with sidelights.
Part Number LD-RRW2 LED taillights Pair
$199
LiteSPOTs LED spotlights were designed to be a low profile under chassis light, a rock light.
The LiteSPOTs are 3 high power white LEDs embedded in a clear resin housing to deliver a
water and corrosion proof package that delivers a wide beam of bright light, with a 4-6
foot focal range. They are not designed as backup or driving lamps. The LiteSPOTs include
a neodymium magnet encased in the resin, providing for easy ‘stick on’ mounting to any
ferrous surface. There is also a thru hole drilled in each one and a supplied self tapping
screw to allow for installation on non-ferrous surfaces. Each LiteSPOT measures 1 3/8” in
diameter and 5/8” thick. Each LiteSPOT comes with 24” of 2 strand 22 guage wire attached
and each until will draw approximately 120 milliamps. LiteSPOTs are sold individually, as
pairs or as our pre-packaged “chassis kit” which includes 6 LiteSPOTs and all the wire,
switch and connectors to wire these 6 under a vehicle. Also work well in pickup boxes to
light up under tonneau covers and truck caps. High heat resistant, can be used under hood
or inside as dome lights.
Part Number LS-W1 Single LiteSPOT
$29
Part Number LS-W2 Pair of LiteSPOTs
$54
Part Number LS-W6 Chassis kit LiteSPOT
$169
8
2014 OffRoadOnly Product Guide (Wrangler TJ products continued)
LItePLATE LED License plate lights are the easiest way to light up your license plate. The
stainless bracket is designed to be mounted behind the license plate, retained by 2 of the
license plate mounting bolts passing thru the large holes which measure 7” from center to
center. The stainless bracket then hangs a polycarbonate black housing containing 3 license
palte facing white LEDs to light up the license plate. The rearward face of the black housing
contains 3 red LEDs that can be hooked up to operate as a 3rd brake light or a clearance
light. Offered in 3 versions, the difference is the length of the wire harness and whether is
has a disconnect in it. The disconnect (LD-PL6) version is designed for use with the Rockhard
4x4 parts License Plate relocation kit. (Rockhard part number RH-4007, available seperately)
and backside.
Part Number LD-PL1 LitePLATE with 1 foot harness
$30
Part Number LD-PL6 LitePLATE with 6 foot harness and disconnect $45
Part Number LD-PL7 LitePLATE with 7 foot harness, no disconnect $45
U-Turn Steering Kit 1997-2006 TJ 1987-2001 XJ 1993-1998 ZJ The U-Turn steering kit has
earned it place as the best bolt on steering kits for Dana 30/44 hybrid axles. This kit corrects
many issues of the factory steering system. It removes the dead spot in the steering of a
Jeep when lifted over 3 inches by having a draglink connected direct to the U-Turn hub,
preventing unwanted movement or play commmon with the factory setup. The proven bolt
on hubs to relocate the tie rod ends allow for a straight tie rod from wheel to wheel for
ultimte strength. This conversion also reduces the sensitivity over center in the steering and
makes evey mile driven feel much more confortable. Tie rod is constructed of 1 3/8” solid
heat treated chromoly, draglink is 1 ¼” solid heat treated chromoly. Tie rod ends are Moog
and Spicer units, both of which are readily available at local auto parts stores for service. UTurn steering kits have been steering Jeeps down the roads and around the trails for over
10 years now.
Part Number UT-J-LHD U-Turn Left hand drive TJ XJ ZJ
$649
Steering Stabilzer Bracket Kit This bracket kit includes u-bolts and a bracket to fit over 1 ¼’
and 1 3/8” round stock. The 5th hole in the bracket accepts a ½” bolt to bolt the moving end
of a standard steering stabilizer to.
Part Number UT-SK Stabilizer bracket kit
$25
9
2014 OffRoadOnly Product Guide (Wrangler TJ products continued)
SwayLOC is the most unique antisway bar for Jeeps. The premise of the SwayLOC is the Dual
Rate design. This design encompases 2 individual torsion bars and a simple method for
engagement. When both bars are used, or the arms are latched together in engaged mode,
there is maximum anti-roll control as the force is controlled by both the outer hollow torsion
bar as well as the inner solid torsion bar. When the latch is moved to the open position, the
two latching arms are allowed to move independently and now the body roll is controlled by
a softer rate torsion bar. This soft bar allows the axle to travel thru full range of motion while
giving a slight amount of roll control to match the rear antisway bar and balancing the front
suspension to the rear. The latching mechanism is either a simple manual ‘flip a lever”
control, where a spring being pulled over center to move the latch, or an even simpler air
cylinder that opens and closes the latch, similar to an ARB operation. An air supply of at least
50psi, maximum 120psi is required for the air control option. Compressed air will work with
proper regulation. Very little volume of air is used in the movement of the cylinder. Each kit
comes with the necessary hardware to fit a wide range of lift heights. SwayLOCs are designed
to bolt onto stock applications, custom or modified track bar brackets or other items in the
area the SwayLOC moves may require modification.
Part Number SL-TJ-LV SwayLOC TJ Manual Flip a Lever
$689
Part Number SL-TJ-RC SwayLOC Tj Remote control air
$889
10
2014 OffRoadOnly Product Guide (Wrangler TJ products continued)
York Compressor Bracket Kit 1997-98 TJ 4.0L This bracket kit is designed to mount a York heavy
duty compressor with a 6 rib clutch to the 4.0L engine with factory A/C. This kit contains the
bracket and hardware to mount a Standard/Heavy Duty York on the passenger side of the A/C
compressor. Kit includes the longer serpentine belt and additional idler pulleys necessary to
assemble this kit. *York compressor and clutch not included, but available seperately.**Some inner fender
trimming will most likely be necessary to install this kit.
Part Number AK-YBKTJ97 York bracket kit TJ 4.0L with A/C
$199
York Compressor Bracket Kit 1997-98 TJ 4.0L This bracket kit is designed to mount a York heavy
duty compressor with a 6 rib clutch to the 4.0L engine without A/C. This kit contains the bracket
and hardware to mount a Standard/Heavy Duty York on the passenger side of the A/C
compressor. Kit includes the longer serpentine belt and additional idler pulleys necessary to
assemble this kit. *York compressor and clutch not included, but available seperately.**Some inner fender
trimming will most likely be necessary to install this kit.
Part Number AK-YBKTJ97NAC York bracket kit TJ 4.0L without A/C $149
York Compressor Bracket Kit 2000-06 TJ 4.0L This bracket kit is designed to mount a York heavy
duty compressor with 6 rib cllutch above the alternator. This bracket replaces the aluminum
mount that mounts the alternator. The factory belt tensioner is retained in this setup. This
places the compressor vertically between the engine and the factory airbox, which may be
retained. Works with the factory alternator or aftermarket alternators as well. Includes a longer
belt, idler pulley and hardware to install.This bracket kit is a direct fit to replace other York
mounting brackets where sliding the cmpressor to tighten the belt is necessary. Install this kit
and eliminate the belt squaeks on startup. *York compressor, clutch, and factory belt tensioner not
included, but available seperately.
Part Number AK-YBKTJ06 York bracket kit TJ 2000-06 With A/C $295
Part Number AK-YBKTJ06NAC York bracket kit TJ 2000-06 Without A/C $295
11
2014 OffRoadOnly Product Guide (Wrangler TJ products continued)
Complete York Air Supply Kit 1997-98 TJ 4.0L With A/C This kit is a complete kit, everything
needed to install the york compressor onto this application. Included are all the high quality,
proven air supply parts that we feel is necessary for the best, most reliable york air supply
system, along with the bracket kit shown above.. Complete installation of this kit will result in
an air supply that generates a tank pressure maximum of 200 psi, and comes with all the
brackets, wire harness and instructions to plumb and operate the system as it was designed.
There is a pair of Milton M Style quick couplers included and our recommendation is to install
them inside the vehicle to keep them clean and coorsion free. Stainless brackets included in
the kit to mount these. This kit includes the Norgren heavy duty oil removal filter with the
automatic drain to return the oil back to the compressor crankcase.
Part Number AK-TJ97 York Air Supply kit for 1997-98 w/A/C
$1599
zComplete York Air Supply Kit 1997-98 TJ 4.0L With out A/C This kit is a complete kit, everything
needed to install the york compressor onto this application. Included are all the high quality,
proven air supply parts that we feel is necessary for the best, most reliable york air supply
system, along with the bracket kit shown above.. Complete installation of this kit will result in
an air supply that generates a tank pressure maximum of 200 psi, and comes with all the
brackets, wire harness and instructions to plumb and operate the system as it was designed.
There is a pair of Milton M Style quick couplers included and our recommendation is to install
them inside the vehicle to keep them clean and coorsion free. Stainless brackets included in the
kit to mount these. This kit includes the Norgren heavy duty oil removal filter with the automatic
drain to return the oil back to the compressor crankcase.
Part Number AK-TJ97 York Air Supply kit for 1997-98 w/oA/C
$1599
Complete York Air Supply Kit 2000-06 TJ 4.0L This kit is a complete kit, everything needed to
install the york compressor onto this application. Included are all the high quality, proven air
supply parts that we feel is necessary for the best, most reliable york air supply system, along
with the bracket kit shown above.. Complete installation of this kit will result in an air supply
that generates a tank pressure maximum of 200 psi, and comes with all the brackets, wire
harness and instructions to plumb and operate the system as it was designed. There is a pair of
Milton M Style quick couplers included and our recommendation is to install them inside the
vehicle to keep them clean and coorsion free. Stainless brackets included in the kit to mount
these. This kit includes the Norgren heavy duty oil removal filter with the automatic drain to
return the oil back to the compressor crankcase.
Part Number AK-TJ06 York Air Supply kit for 2000-06 TJ w/A/C
$1599
Part Number AK-TJ06NAC York Air Supply kit for 2000-06 TJ w/oA/C $1599
12
2014 OffRoadOnly Product Guide (Wrangler TJ products continued)
AiROCK Air suspension 1997-06 Wrangler JK 1997-06 The AiROCK air suspension kit is our
flagship product. Leading the offroad (and onroad) category by providing a one button
user adjustable suspension that allows the operator to adapt the vehicle best to changing
offroad conditions as well as a completely automated Active Air Management system for
on road driving when vehicle speed exceeds 30 mph. This kit contains all the components
to install into this model Wrangler JK. Not included is an air supply, of which the Complete
York Air Supply Kit is recommended. Additional required items once that Complete Air
Suply kit is included are the Air Filter regulator kit. This AiROCK kit does include the shocks,
custom manufactured for ORO by Radflo. Contact ORO for more details.
Part Number AR-TJSA AiROCK Air Suspension Kit for 1997-06 TJ Short arm
$4995
13
2014 OffRoadOnly Product Guide
Grip-N-Go Shift knob Hand Throttle Any manual transmission vehicle that has a cable driven throttle
plate. The Grip-N-Go hand throttle is designed to repalce the shift knob on any manual transmission
vehicle. Once installed, the level protruding from the side of the shift knob is tied to the throttle of the
vehicle. Operating this lever to open throttle is made easy by a multi step pivot for the lever. The first part
of the lever movement is designed to allow less force to topen the throttle and more finite control. Once
the lever reaches horizontal, then the lever changes the pivot point, allowing for maximum cable travel
for the remaining of the lever movement. The throttle body side of the cable attachment includes
instructions on adapting ot a variety of vehicles. Severa bushings come with the kit to allow it to replace
multiple shift knob threads. Parts included for most common American made and some import models.
Part Number GNG Grip-N-Go Hand Throttle
$109
5 Pin TJ Turnsignal falsher for LED taillights 2000-06 TJ This flasher is a plug n play option
to convert the TJ 5 pin flasher to LED compatible. The 2000-6 Wrnagler TJs with the headlight
switch on the turn signal stalk require a flasher replacement to correct the fast flash. This flasher
that we source will correct those flashing issues. Please note: Our customers have used with on
these Wrangelrs and converted the front turn sgnal bulbs to LEDS as well. On some occasions
this has proven to work well for that conversion also. However, most of the time, converting
front and rear lights to LEDS and installing this flasher will result in flashing issues. Contact us
for more info regarding specific applications.
Part Number LD-FLTJ01 Flasher 5 Pin TJ
$34
ADE Theft Deterant System Instructions included for 1997-06 TJ but will work on any
12 volt vehicle system. This kit is a simple way to require a secret swipe of a magnet to engage
an electronic circuit. On the Wranglers as it was designed, the relay interupts the PDC relay
circuit, and unless the magnet is swiped, the computer and fuel injection systems will not
power up. The result, engine will crank but not fire, vehicle will remain where you parked it
until the magnet is swiped. Custom application, determine which circuit you wish to disable,
insert the ADE relay and the same protection will be just the same. The relay used is the
common 5 pin relay, available at all auto parts stores. The harness is setup for a bypass, simply
make a connection between two wires and the system is completely removed from the
system. Easily installed by anyone handing with a wire crimper.
Part Number TDS-ADE II
Contact:
$59
OffRoadOnly
1971 Seneca Road Unit E
Eagan, MN 55122
651.644.2323
orders@offroadonly.com
www.offroadonly.com
14
www.facebook.com/offroadonly.oro