Pioneer DEH
Transcription
Pioneer DEH
WWW.PCBOOK.IR ORDER NO. CRT3219 DEH-P8MP/XN/UC MULTI-CD CONTROL HIGH POWER CD/MP3/WMA PLAYER WITH FM/AM TUNER DEH-P8MP /XN/UC DEH-P80MP/XN/UC DEH-P1Y/XN/ES This service manual should be used together with the following manual(s): Model No. CX-3098 Order No. CRT3179 Mech.Module S10WMAcode2 Remarks CD Mech. Module:Circuit Description, Mech. Description, Disassembly For details, refer to "Important symbols for good services". PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 PIONEER CORPORATION 2004 K-ZZD.MAY 2004 printed in Japan 1 WWW.PCBOOK.IR 2 3 4 SAFETY INFORMATION CAUTION A This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician. WARNING This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause cancer, birth defects or other reproductive harm. Health & Safety Code Section 25249.6 - Proposition 65 B - Service Precaution 1. You should conform to the regulations governing the 3. To protect the pickup unit from electrostatic discharge product (safety, radio and noise, and other regulations), during servicing, take an appropriate treatment and should keep the safety during servicing by following (shorting-solder) by referring to "the DISASSEMBLY" the safety instructions described in this manual. on page 63. 2. Before disassembling the unit, be sure to turn off 4. After replacing the pickup unit, be sure to check the the power. Unplugging and plugging the connectors grating. (See page 59.) during power-on mode may damage the ICs inside the unit. C [ Important symbols for good services ] In this manual, the symbols shown-below indicate that adjustments, settings or cleaning should be made securely. When you find the procedures bearing any of the symbols, be sure to fulfill them: 1. Product safety You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and should keep the safety during servicing by following the safety instructions described in this manual. 2. Adjustments To keep the original performances of the product, optimum adjustments or specification confirmation is indispensable. In accordance with the procedures or instructions described in this manual, adjustments should be performed. D 3. Cleaning For optical pickups, tape-deck heads, lenses and mirrors used in projection monitors, and other parts requiring cleaning, proper cleaning should be performed to restore their performances. 4. Shipping mode and shipping screws To protect the product from damages or failures that may be caused during transit, the shipping mode should be set or the shipping screws should be installed before shipping out in accordance with this manual, if necessary. 5. Lubricants, glues, and replacement parts E Appropriately applying grease or glue can maintain the product performances. But improper lubrication or applying glue may lead to failures or troubles in the product. By following the instructions in this manual, be sure to apply the prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed ones should be used. F 2 DEH-P8MP/XN/UC 1 2 3 4 5 WWW.PCBOOK.IR 6 7 8 CONTENTS SAFETY INFORMATION......................................................................................................................................2 1. SPECIFICATIONS .............................................................................................................................................4 2. EXPLODED VIEWS AND PARTS LIST.............................................................................................................8 2.1 PACKING(DEH-P8MP/XN/UC,DEH-P80MP/XN/UC) .................................................................................8 2.2 PACKING(DEH-P1Y/XN/ES) ....................................................................................................................10 2.3 EXTERIOR ...............................................................................................................................................12 2.4 CD MECHANISM MODULE .....................................................................................................................16 3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ..........................................................................................18 3.1 BLOCK DIAGRAM....................................................................................................................................18 3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE) ..............................................................................20 3.3 KEYBOARD UNIT ....................................................................................................................................26 3.4 CD MECHANISM MODULE(GUIDE PAGE) .............................................................................................28 4. PCB CONNECTION DIAGRAM ......................................................................................................................38 4.1 TUNER AMP UNIT ...................................................................................................................................38 4.2 SWITCH UNIT ..........................................................................................................................................42 4.3 KEYBOARD UNIT ....................................................................................................................................43 4.4 CD MECHANISM MODULE .....................................................................................................................44 5. ELECTRICAL PARTS LIST .............................................................................................................................46 6. ADJUSTMENT ................................................................................................................................................55 6.1 CONNECTION DIAGRAM........................................................................................................................55 6.2 OEL UNIT ADJUSTMENT ........................................................................................................................56 6.3 CD ADJUSTMENT ...................................................................................................................................57 6.4 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT.....................................................59 6.5 ERROR MODE .........................................................................................................................................61 6.6 OEL SCREENSAVER STUDIO LKA TO LKD APPLICATION ..................................................................62 6.7 SYSTEM MICROCOMPUTER TEST PROGRAM ....................................................................................62 7. GENERAL INFORMATION .............................................................................................................................63 7.1 DIAGNOSIS..............................................................................................................................................63 7.1.1 DISASSEMBLY......................................................................................................................................63 7.1.2 CONNECTOR FUNCTION DESCRIPTION ..........................................................................................68 7.2 IC ..............................................................................................................................................................69 7.3 EXPLANATION .........................................................................................................................................81 7.3.1 OPERATIONAL FLOW CHART .............................................................................................................81 7.3.2 CIRCUIT DESCRIPTIONS ....................................................................................................................82 7.4 CLEANING ...............................................................................................................................................84 8. OPERATIONS .................................................................................................................................................85 A B C D E F DEH-P8MP/XN/UC 5 6 7 8 3 1 WWW.PCBOOK.IR 2 3 4 3 4 1. SPECIFICATIONS A B C D E F 4 DEH-P8MP/XN/UC 1 2 5 WWW.PCBOOK.IR 6 7 8 A B C D E F DEH-P8MP/XN/UC 5 6 7 8 5 1 WWW.PCBOOK.IR 2 3 4 3 4 A B C D E F 6 DEH-P8MP/XN/UC 1 2 5 WWW.PCBOOK.IR 6 7 8 A B C D E F DEH-P8MP/XN/UC 5 6 7 8 7 WWW.PCBOOK.IR 1 2 3 4 2. EXPLODED VIEWS AND PARTS LIST NOTES : • Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List. • Screw adjacent to mark on the product are used for disassembly. • For the applying amount of lobricants or glue, follow the instructions in this manual. (In the case of no amount instructions,apply as you think it appropriate.) " A 2.1 PACKING(DEH-P8MP/XN/UC,DEH-P80MP/XN/UC) 5 9 12 10 6 11 8 15 7 3 14 B 26 13 4 16 17 C 1 27 2 20 D 19 24 28 E 25 18 24 23 23 22 21 F 8 DEH-P8MP/XN/UC 1 2 3 4 WWW.PCBOOK.IR 5 6 7 8 (1) PACKING(DEH-P8MP/XN/UC,DEH-P80MP/XN/UC) SECTION PARTS LIST Mark No. Description 1 2 3 4 5 * * Cord Assy Cord Assy Accessory Assy Spring Screw Assy Mark No. Part No. CDE7612 CDE7482 CEA4302 CBH1650 CEA4303 * 6 7 8 9 10 Screw Bolt(M5x16) Polyethylene Bag Screw Screw CBA1650 CBA1783 CEG-127 CRZ50P090FTC JPZ20P060FZK 11 12 13 14 15 Nut Screw Polyethylene Bag Handle Strap NF50FTC TRZ50P080FTC CEG-158 CNC5395 CNC5402 16 Bush 17-1 Polyethylene Bag * * CNV3930 CEG1116 * Description Part No. 17-2 Owner's Manual 17-3 Installation Manual 17-4 Caution Card See Contrast table(2) See Contrast table(2) CRP1307 17-5 17-6 17-7 18 19 Caution Card Warranty Card Card Polyethylene Bag Carton CRP1310 See Contrast table(2) See Contrast table(2) CEG1173 See Contrast table(2) 20 21 22 23 24 Sub Carton Contain Box Protector Protector Protector CHA3258 See Contrast table(2) CHP2546 CHP2539 CHP2538 25 26 27 28 Protector Remote Control Unit Case Assy Caution Card CHP2541 CXC2665 CXC3572 CRP1311 A B (2) CONTRAST TABLE DEH-P8MP/XN/UC and DEH-P80MP/XN/UC are constructed the same except for the following: Mark * * NO Description DEH-P8MP/XN/UC C DEH-P80MP/XN/UC 17-2 17-3 17-6 17-7 19 Owner's Manual Installation Manual Warranty Card Card Carton CRD3844 CRD3845 CRY1070 Not used CHG5212 CRD3846 CRD3847 Not used ARY1048 CHG5211 21 Contain Box CHL5212 CHL5211 Owner's Manual,Installation Manual Part No. Language CRD3844 English, French CRD3845 English, French CRD3846 English, French CRD3847 English, French D E F DEH-P8MP/XN/UC 5 6 7 8 9 WWW.PCBOOK.IR 1 2 3 4 2.2 PACKING(DEH-P1Y/XN/ES) 5 9 A 12 6 3 8 14 26 13 4 16 B 17 1 27 2 C 20 19 24 28 D 25 18 24 E 23 23 22 21 F 10 DEH-P8MP/XN/UC 1 2 3 4 WWW.PCBOOK.IR 5 6 7 8 PACKING(DEH-P1Y/XN/ES) SECTION PARTS LIST Mark No. * * Description Mark No. Part No. 1 2 3 4 5 Cord Assy Cord Assy Accessory Assy Spring Screw Assy CDE7612 CDE7482 CEA4301 CBH1650 CEA3849 6 7 8 9 10 Screw ••••• Polyethylene Bag Screw ••••• CBA1650 11 12 13 14 15 ••••• Screw Polyethylene Bag Handle ••••• 16 Bush 17-1 Polyethylene Bag * CEG-127 CRZ50P090FTC Part No. 17-2 Owner's Manual 17-3 Owner's Manual 17-4 Installation Manual CRD3848 CRD3849 CRD3850 17-5 17-6 18 19 20 Caution Card Caution Card Polyethylene Bag Carton Sub Carton CRP1307 CRP1310 CEG-162 CHG5210 CHA3258 21 22 23 24 25 Contain Box Protector Protector Protector Protector CHL5210 CHP2546 CHP2539 CHP2538 CHP2541 26 27 28 Remote Control Unit Case Assy Caution Card CXC2665 CXC3572 CRP1311 TRZ50P080FTC CEG-158 CNC5395 CNV3930 CEG1116 Description * A B Owner's Manual,Installation Manual Part No. Language CRD3848 English, Spanish, Portuguese(B) CRD3849 Traditional Chinese, Arabic CRD3850 English, Spanish, Portuguese(B), Traditional Chinese, Arabic C D E F DEH-P8MP/XN/UC 5 6 7 8 11 1 WWW.PCBOOK.IR 2 3 4 3 4 2.3 EXTERIOR A B C D E F 12 DEH-P8MP/XN/UC 1 2 WWW.PCBOOK.IR 5 6 7 8 (1) EXTERIOR SECTION PARTS LIST Mark No. Description Part No. Mark No. Description Switch Unit Switch(S1) Spring Switch(S2) Holder Unit Holder Unit CWS1389 CSN1051 CSN1052 CXC2196 CXC2197 Part No. 1 2 3 4 5 Screw Screw Screw(M2x2.5) Screw(M2.6x4) Flat Cable BMZ26P200FTC BSZ26P060FTC CBA1641 CBA1769 CDE7468 56 57 58 59 60 6 7 8 9 10 Cord Assy Fuse(10A) ••••• Cap IC(IC201) CDE7482 CEK1136 CNS1472 PAL008A 61 62 63 64 65 Arm Unit Arm Unit Arm Unit Arm Unit Chassis Unit CXC2198 CXC2199 CXC2200 CXC2201 See Contrast table(2) 11 12 13 14 15 Resistor Cord Assy Cord Assy Cord Assy Cap RS1/2PMF102J See Contrast table(2) CDE7484 CDE7612 CNV6727 66 67 68 69 70 Motor Unit(M871) FM/AM Tuner Unit Gear Unit Screw Washer CXC2204 CWE1646 CXC2205 JFZ20P025FTC YE15FTC 16 17 18 19 20 Case Holder Earth Plate Insulator Insulator CNB2945 CNC8659 CND2171 CNM8638 CNM8790 71 72 73 74 75 Panel Unit Remote Control Unit Cover Screw(M2x2) Screw(M2x2) CXC2603 CXC2665 CZN5357 CBA1561 CBA1633 21 22 23 24 25 Cushion Panel Tuner Amp Unit Screw Screw CNM9126 CNS7772 See Contrast table(2) BMZ26P200FTC BSZ26P080FTC 76 77 78 79 80 Screw(M2x3.5) Spring Connector Holder Flexible PCB CBA1754 CBH2530 CKS4796 CND2172 CNP7698 26 27 28 29 30 Antenna Cable Clamper Connector(CN361) Plug(CN981) Plug(CN871) CDH1336 CEF1033 CKM1389 CKM1428 CKS-786 81 82 83 84 85 Arm Guide Guide Case Unit Detach Grille Assy CNV6962 CNV6967 CNV6968 CXC2670 See Contrast table(2) 31 32 33 34 35 Connector(CN571) Connector(CN704) Connector(CN101) Connector(CN701) Connector(CN801) See Contrast table(2) CKS3125 CKS3408 CKS3837 CKS4811 86 87 88 89 90 Screw Button(OPEN/RESET) Button(BAND) Button(ENT/EQ/EQ-EX) Button(CLOCK/DISP/LIST) BPZ20P060FZK CAC8442 CAC8443 CAC8444 CAC8450 36 37 38 39 40 Holder(CN402) Case Holder Holder Heat Sink CNC5399 CNC8138 CND2029 CND2030 CND2031 91 92 93 94 95 Button(ATT/OFF/SRC) Cover Lighting Conductor Keyboard Unit Connector(CN1901) CAC9003 CNS7770 CNV7966 CWM9290 CKS4795 41 42 43 44 45 Insulator Heat Sink Holder Drive Unit Screw CNM6249 CNR1728 CND1054 See Contrast table(2) BMZ26P040FTC 96 97 98 99 100 Holder Double-sided Seal Spacer Spacer Holder CND2028 CNM8673 CNM9141 CNM9142 CNV7965 46 47 48 49 50 Screw(M2x2) Spring Cord Holder Holder CBA1633 CBL1632 CDE7392 CND1848 CND1850 101 102 103 104 105 OEL Unit MXS8202 Sub Grille Assy See Contrast table(2) Knob Unit CXC3581 CD Mechanism Module(S10CODE2)CXK5666 Screw ISS26P055FTC 51 52 53 54 55 Insulator Gear Gear Gear Gear CNM8797 CNV7752 CNV7753 CNV7754 CNV7755 106 107 108 109 110 ••••• Diode(D241,242) Diode(D243,244) Transistor(Q241,242) Transistor(Q742,902,921) 6 7 B C D E FMG22 FMJ-2303 FKV550N 2SD2375 DEH-P8MP/XN/UC 5 A 8 F 13 WWW.PCBOOK.IR 1 2 3 4 (2) CONTRAST TABLE DEH-P8MP/XN/UC, DEH-P80MP/XN/UC and DEH-P1Y/XN/ES are constructed the same except for the following: Mark A NO Description DEH-P8MP/XN/UC DEH-P80MP/XN/UC DEH-P1Y/XN/ES 12 23 31 44 65 Cord Assy Tuner Amp Unit Connector(CN571) Drive Unit Chassis Unit CDE7483 CWM9287 CKS3125 CXC2206 CXC2203 CDE7483 CWM9288 CKS3125 CXC2206 CXC2203 Not used CWM9289 Not used CXC3562 CXC3561 85 102 Detach Grille Assy Sub Grille Assy CXC2695 CXC3235 CXC2696 CXC3236 CXC2697 CXC3237 B C D E F 14 DEH-P8MP/XN/UC 1 2 3 4 5 WWW.PCBOOK.IR 6 7 8 A B C D E F DEH-P8MP/XN/UC 5 6 7 8 15 WWW.PCBOOK.IR 1 2 3 4 2.4 CD MECHANISM MODULE 5 42 13 A 81 34 5 15 13 22 E 5 F 93 13 92 A B 44 5 54 1 13 C G 83 86 68 D 52 B 26 82 86 53 28 I H 4 28 37 71 4 55 4 1 2 J 87 36 4 45 23 1 23 72 18 29 51 64 38 50 73 K 10 47 75 1 C I 2 24 76 B 49 1 7 61 E M 2 A Q 27 8 H 21 G L M 1 57 D 90 48 1 79 77 F 1 63 2 59 N D O R 16 17 12 1 58 67 J 3 1 78 33 P 2 62 46 60 20 2 80 40 1 6 1 N 1GEM1024 2GEM1045 3GEM1035 1 11 1 25 69 P 43 L 30 19 56 60 39 K 70 14 E 74 41 R 85 31 C 91 14 D 65 1 3 F Q 35 O 85 31 94 2 66 85 16 DEH-P8MP/XN/UC 1 2 3 4 89 10 WWW.PCBOOK.IR 5 6 7 8 CD MECHANISM MODULE PARTS LIST Mark No. Description Mark No. Part No. 1 2 3 4 5 CD Core Unit(S10WMACODE2) CWX2952 Connector(CN101) CKS4182 Connector(CN901) CKS4017 Screw BMZ20P035FTC Screw BSZ20P040FTC 6 7 8 9 10 Screw(M2x4) Screw(M2x3) Screw(M2x3) ••••• Washer CBA1362 CBA1511 CBA1527 11 12 13 14 15 Washer Spring Spring Spring Spring CBF1060 CBH2390 CBH2606 CBH2607 CBH2608 16 17 18 19 20 Spring Spring Spring Spring Spring CBH2609 CBH2610 CBH2735 CBH2612 CBH2613 21 22 23 24 25 Spring Spring Spring Spring Spring CBH2614 CBH2615 CBH2616 CBH2617 CBH2620 26 27 28 29 30 Spring Spring Spring Spring Spring CBH2621 CBH2641 CBH2642 CBH2643 CBH2659 31 32 33 34 35 Spring ••••• Shaft Frame Frame CBH2688 36 37 38 39 40 Bracket Bracket Arm Arm Lever CNC9966 CND1895 CNC9968 CND1909 CND2032 41 42 43 44 45 Lever Sheet Collar Guide Arm CNC9984 CNM8134 CNV7798 CNV7799 CNV7800 46 47 48 49 Rack Holder Holder Arm CNV7199 CNV7201 CNV7202 CNV7203 CBF1038 CLA4441 CNC9962 CNC9963 Description Part No. 50 Gear CNV7207 51 52 53 54 55 Gear Gear Gear Gear Gear CNV7208 CNV7209 CNV7210 CNV7211 CNV7212 56 57 58 59 60 Rack Arm Arm Guide Roller CNV7214 CNV7215 CNV7216 CNV7217 CNV7218 61 62 63 64 65 Gear Arm Arm Arm Damper CNV7219 CNV7221 CNV7220 CNV7222 CNV7313 66 67 68 69 70 Damper Arm Arm Guide Guide CNV7314 CNV7341 CNV7342 CNV7360 CNV7361 71 72 73 74 75 Holder Arm Gear Damper Motor Unit(M1) CNV7437 CNV7805 CNV7595 CNV7618 CXB6007 76 77 78 79 80 Chassis Unit Screw Unit Gear Unit Arm Unit Arm CXC2318 CXB8729 CXC2397 CXC2316 CND1896 81 82 83 84 85 Arm Motor Unit(M2) Bracket ••••• Screw(M2x5) CND1894 CXB8933 CNC9985 86 87 88 89 90 Screw Screw ••••• Washer Pickup Unit(P9.9MP3)(Service) YE20FTC CXX1805 91 92 93 94 Screw Spring Clamper Connector(CN902) IMS26P030FTC CBL1635 CNV7197 CKS2193 6 B C D EBA1028 JFZ20P020FTC JGZ17P022FTC E F DEH-P8MP/XN/UC 5 A 7 8 17 WWW.PCBOOK.IR 1 2 3 4 3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM 3.1 BLOCK DIAGRAM A A TUNER AMP UNIT VDD CN101 CN401 AM ANT 1 1 8 NC NC NC NC Q101 18 19 20 21 NC 14 DO 11 BUS+L 7 5V IC 5 3.3V IP-B BUS5 IC 10 6 HA122 FMRF OSC LPF BUS+ 8 I ATT Rch B 5 1 BUS-L 11 IC 3 EEPROM 5.0V ANTENNA CK SL DI 10 9 8 CE1 5 ROM_VDD CE2 WC FM/AM TUNER UNIT 13 ← 7 6 2 IC 2 2.5V IC 1 3.3V FM ANT 3 ATT MIXER, IF AMP Lch DET, FM MPX 24 23 FMRF T51 RF adj CF52 DGND AUDIOGND NC 12 15 22 16 VDD_3.3 OSCGND 2 VCC RFGND CF51 4 IC 4 2.5V 3.3V 2.5V 3.3V ← ANT adj 17 Q871 TUNER 3.3V REGULATOR IC 451 TUN 3.3V SYS+B Q872 1 SYS+B BA033FP C M871 FLAP MOTOR B B.UP 3 CN871 ASLIN 4 5 OUT1 3 4 OUT2 14 5 M SWITCH UNIT 11 IC 871 6 ELEC SO BA6288FS 15 S1 BUSL+ CD L 41 IN2-L TUN L 3 S2 NOIS 42 IN3-L 44 IN4-L 43 IN4+L CLOSE FCLSSW BUSL- OPEN 2 FOPNSW 1 9 8 SP 601 D CD CORE UNIT(S10WMACODE2) LEVEL INDICATO V3R3D CN902 CN101 Q101 143 LD+ 14 1 4 M2 LOADING/CARRIAGE MOTOR A 50 fopnsw MUTE SYSPW2 CN901 31 B CN701 10 KEYAD KYDT 14 LOUT Q651 FOP SYSPW TOP XIN TD/FD 14 SD/MD 12 16 SOP 15 SOM 18 LCOP 17 LCOM M LOEJ 22 53 9 47 VDD 13 X1 CD DRIVER M RST1 X702 12 FOP 13 TOP M1 SPINDLE MOTOR CDRX MICRO COMPUTER FTxD LOEJ 31 30 97 SYSPW2 89 KEYAD 34 KYDT 1 10 reset DEH-P8M DEH-P80M 1 13 B X601 11 20 IC 601(2/2) PD5925A OELPW Q822 B.UP Q821 BRST,BRXEN,BSRQ 26 IC 701 PE5423A 32 E 25 85 84 BDATA,BSCK ILMPW 41 CONT IC 301 BA5835FM 4 IC 652 XOUT BD4835G FRxD CONT RESET 2 X2 92 SYSTEM CONTROLLER BRST,BRXEN,BSRQ ejtin BDATA,BSCK Q742 CLAMP VD VD 12EJ 8EJ DSCSNS HOME VDCONT CD3VON 3 21 4 20 19 5 VD B.UP Q741 49 47 43 CROSSKEY FO+ 1 TO+ 4 2 7 LVLINL 42 91 DSENS R ROT0 FOCUS ACT. MONITOR TRACKING ACT. DIODE F,E 3 fclssw PD RF AMP, CD DECODER, MP3 AND WMA DECODER DIGITAL SERVO/DATA PROCESSOR AC,BD HOLOGRAM UNIT RX IC 201 UPD63761GJ LD 51 ROT1 5 CDTX SWVDD 15 5 3 DPDT D 15 4 KYDT LDMD TX 142 22 PEE gdtc@ LASER DIODE CN704 gdtc! PICKUP UNIT (P9.9MP3)(SERVICE) EVST,EVCK,EVDT BUZZER 34 33 38 87 35 36 46 VDCONT VDCONT C Q743 S902 CLAMP S904 12EJ S903 S905 S901 8EJ DSCSNS HOME CD3VON 1 23 CD3VON Q831 Q744 VDD 3.3V REGULATOR 3VDD 3 V3R3D IC 203 NJM2391DL1-33 1 VD2 3 IC 703 2 VDD 3.3V REGULATOR V1R5 19 VDD B A GDTC1 GDTC1 VDD 1,3 IC 501 S-L2980A15MC-C6A 2 22 VD2 CDTX CDRX 13 11 12 8 9 GDTC2 F GDTC2 10 IC 801(2/2) TC74VHCT125AFT 18 DEH-P8MP/XN/UC 1 2 3 3 5 GDTC1 V3R3D 1.5V REGULATOR 1 IC 801(1/2) 2 TC74VHCT125AFT GDTC2 VD2 5 5 S-812C33AUA-C2N 4 6 4 OEL WWW.PCBOOK.IR 5 6 7 8 A Q881(1/2) Q883 17 8 PL SWL VCC1 01 CN361 FL- Q101 10 FL+ 8 B.UP 5 1 RL- Q885 2 80 RL IC 341 15 PA2028A 10 RL+ Q881(2/2) ICERORR ASENBO RL 6 6 HA12240FP 2 RX 27 IC 101 8 IPPW C TX FL CE1 70 DO 2 IPPW VDD REGULATOR 99 CK 100 95 Q902 tunpce@ VDD TUNPDI TUNPDO TUNPCK SL B.UP 67 DALMON TELIN IC 601(1/2) PD5925A CN981 Q951 VDD 8 bsens TELEPHONE MUTE Q243 10 IC 241 UPC494GS MIC 321 ELECTRONIC VOLUME/ MICROPHONE SOURCE SELECTOR 1 15 NOISEDET 42 IN3-L 44 IN4-L IC 131 43 IN4+L PML009A TUN L PL FL RL SEL_OUT_L 41 IN2-L CD L MICIN 13 C B.UP NJM2406F IC 221 MIC Q247 Q246 Q244 VCC2 FL+ 21 1 VCC2 12 10 12 11 13 7 VCC1 MG1 RL+ 8 FL- 10 FL+ 4 RL- POWER AMP RLIN 6 RL+ MUTE C ACC 18 GND 4 FL- 2 FL+ 8 5 RLRL+ 11 B.REM RL- 2 IC 201 PAL008A FLIN Q221 B.REMOTE 27 5 B.UP MUTE Q364 LEVEL INDICATOR IC 171 16 FL- Q242 3 EVST,EVCK,EVDT 7 ACC 10A VCC1 9 6 88 1 9 8 17 Q241 ACCMON ddchk 3 FUSE ACC 4 5 ASLIN ILM 13 ACC SYS+B 60W 1k(1/2W) ILM SENSE Q248 VDD 40W 4 sel^)w 81 BACKUP 10A ACC SENSE S421 60W/40W FUSE 9 Q941 53 FLPOPN 15 AC 81 54 FLPPW 52 FLPCLS B.UP Q931 72 isens 93 TELMUTE 14 BACKUP SENSE 73 asens ASLIN B Q901 TUNPCE1 98 DI FRONT L 1 Q363 SYSTEM CONTROLLER 69 FL RX 79 ce@ 13 12 3A 28 FU351 1 TX BUS+ USL- REAR L 5 Q362 Q882 IP-BUS DRIVER BUS5 BUSL+ SUB WOOFER L 9 Q361 IC 561 1 TPD1018F SYSPW2 6 SYS +B REGULATOR BU Q921 Q202 5 BU MUTE SYS+B 92 Q922 SYS+B Q201 NJM4558MD 85 84 SYSPW2 Q923 Q501 89 KEYAD 34 KYDT D DEH-P8MP/XN/UC DEH-P80MP/XN/UC SYS+B 1 13 SYSPW Q842 Q841 B.UP DEH-P8MP/XN/UC DEH-P80MP/XN/UC CN571 X601 11 6 20 IC 841 NJM2360M 5 1 2 3 KEYAD KYDT OEL+B WIRED REMOTE CONTROL Q822 B.UP Q821 CN801 41 IL+B CN1901 7 7 C ILLUMINATION IL+B S1902 OPEN 42 EJSW 16 S1901 RESET 91 14 RST1 DSENS 15 KEYBOARD UNIT 16 OPEN Q1952 14 RST1 15 16V 3.3V Q1951 DSENS FLASH MEMORY SEL/VOL 11 ROT1 10 CLOSSKEY 9 10 ROT1 9 JOYST reset S1913 ROT0 ROT0 11 ce E 12 26 IC 1953 A18 16 37 VCC PD6469A A19 9 Q1953 3.3V 3.3V REGULATOR Q831 SWDVDD VDD SWVDD 5 IC 1941 1 KEY MATRIX S-818A33AUC-BGN 4 1 5 97 REM 14 OEL+B 12 5 12 5 28 KYDT OELB 46 47 48 DPDT 93 OEL CONTROLLER/ KEY CONTROLLER 4 KYDT 60 flstsy IC 1952 RS-140 REMOTE CONTROL SENSOR 27 KTDT 96 FL12PON DPDT cs) 13 cs! 6 13 cs@ 5 DPDT VDD OPT IN 3 VDD 1 /2) 2 5AFT DTC2 8 AVCC DTC1 8 KEY DATA XIN XOUT 13 X1940 OEL UNIT 11 OEL DATA IC 1951 PD5933A IC1970 IC1971 2,8 8,21 16V 16V F Q1981 12V Q1982 DEH-P8MP/XN/UC 5 6 7 8 19 WWW.PCBOOK.IR 1 2 3 4 3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE) Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST". A-a A-a A-b A-a CN902 A-b Guide page Detailed page A-b P P P CD:0dBs FM:-20.5dBs AM:-31.0dBs IP-BUS: +2.2dBs CD: 0dBs D B WIRED REMOTE CONTROL CN901 A-a Large size SCH diagram CD CORE UNIT(S10WMACODE2) A FM:+2.6dBs AM: -7.9dBs IP-BUS:+8.3dBs CD:+8.1dBs D FM(100%):-19.5dBs AM(30%):-30.0dBs P FM/AM TUNER UNIT FM/AM ANTENNA C P 60W/40W C CN1901 E P P IP-BUS:+2.2dBs 8 9 10 11 5 6 7 1 2 3 4 S2 OPEN CSN1052 3 A B 20 2 S1 CLOSE CSN1051 1 F M M871 FLAP MOTOR CXC2204 B SWITCH UNIT DEH-P8MP/XN/UC 1 2 3 4 5 WWW.PCBOOK.IR 6 7 8 A-b A A TROL A : DEH-P8MP/XN/UC B : DEH-P80MP/XN/UC C : DEH-P1Y/XN/ES TUNER AMP UNIT FM:+13.1dBs AM: +2.6dBs IP-BUS:+18.8dBs CD:+18.6dBs B SUB WOOFER R CH SUB WOOFER L CH REAR R CH REAR L CH FRONT R CH FRONT L CH FM:+2.6dBs AM: -7.9dBs BUS:+8.3dBs CD:+8.1dBs > C D GND P ACC CEK1136 10A P > >CEK1136 BACKUP 10A TEL MUTE P ILL B.REM P 1K(1/2W) RLFRRL+ FR+ FLRRFL+ RR+ FM:+28.6dBs AM:+18.1dBs IP-BUS:+34.3dBs CD:+34.1dBs E NOTE : Symbol indicates a resistor. No differentiation is made between chip resistors and discrete resistors. Symbol indicates a capacitor. No differentiation is made between chip capacitors and discrete capacitors. The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Decimal points for resistor and capacitor fixed values are expressed as : 2.2 ← 2R2 0.022 ← R022 A DEH-P8MP/XN/UC 5 6 F 7 8 21 22 1 2 FM:-20.5dBs AM:-31.0dBs IP-BUS: +2.2dBs CD: 0dBs 1 FM:+2.6dBs AM: -7.9dBs IP-BUS:+8.3dBs CD:+8.1dBs WIRED REMOTE CONTROL 2 CD CORE UNIT(S10WMACODE2) P P CD:0dBs E P P A-a A-b WWW.PCBOOK.IR 3 A-a DEH-P8MP/XN/UC 3 4 FM(100%):-19.5dBs AM(30%):-30.0dBs M TUNER UNIT B CN902 CN901 A-b D 1 4 A 2 C D F FM/AM ANTENNA 6 7 FM/AM TUNER UNIT FM/AM AN IP-BUS:+2.2dBs 7 1 2 3 4 5 6 8 9 10 11 P 2 3 M M871 FLAP MOTOR CXC2204 A-a A-b P P 60W/40W 7 4 DEH-P8MP/XN/UC 8 B SWITCH UNIT 1 S2 OPEN CSN1052 3 S1 CLOSE CSN1051 5 WWW.PCBOOK.IR 6 CN1901 C 5 8 A A-b B C D E F A-a B 23 A TUNER AMP UNIT A-b 24 1 1 2 > FRONT L CH FRONT R CH REAR L CH REAR R CH SUB WOOFER R CH SUB WOOFER L CH FM:+13.1dBs AM: +2.6dBs IP-BUS:+18.8dBs CD:+18.6dBs A 2.6dBs 7.9dBs 8.3dBs 8.1dBs C A : DEH-P8MP/XN/UC B : DEH-P80MP/XN/UC C : DEH-P1Y/XN/ES B L A-a A-b 1 WWW.PCBOOK.IR 2 3 3 4 D E F 2 DEH-P8MP/XN/UC 4 5 NOTE : Symbol indicates a resistor. No differentiation is made between chip resistors and discrete resistors. Symbol indicates a capacitor. No differentiation is made between chip capacitors and discrete capacitors. 1K(1/2W) RR+ FL+ RR- FL- FR+ RL+ FR- RL- B.REM ILL TEL MUTE BACKUP ACC GND 6 6 The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. FM:+28.6dBs AM:+18.1dBs IP-BUS:+34.3dBs CD:+34.1dBs P 10A >CEK1136 > CEK1136 10A WWW.PCBOOK.IR 7 3 4 DEH-P8MP/XN/UC 7 8 A-a A-b Decimal points for resistor and capacitor fixed values are expressed as : 2.2 ← 2R2 0.022 ← R022 P P P 5 8 A B C D E F A-b 25 WWW.PCBOOK.IR 1 2 3 4 3.3 KEYBOARD UNIT A REMOTE CONTROL SENSOR A CN801 B VOL/SEL OPEN C RESET D ENT ATT EQ LIST CLOCK BAND SRC EQ-EX DISP E F C 26 DEH-P8MP/XN/UC 1 2 3 4 5 WWW.PCBOOK.IR 6 7 8 C A KEYBOARD UNIT OL B C OEL/KEY CONTROLLER FLASH MEMORY A12 DQ15/A-1 D E OEL UNIT MXS8202 F C DEH-P8MP/XN/UC 5 6 7 8 27 WWW.PCBOOK.IR 1 2 3 4 3.4 CD MECHANISM MODULE(GUIDE PAGE) A S C T F S C T F D-a L209 C217 B R1 PICKUP UNIT(P9.9MP3)(SERVICE) % F F F F T T T T F F T T T T F F AND T T T F F C # @ T F F D Pull-down 4.00MHz 3 $ 2 S T T 7 9 1 C F F E M1 CXB6007 SPINDLE MOTOR 8 5 0 S S S S 4 F F C T C T C S S C CD DRIVER C C M2 CXB8933 LOADING/CARRIAGE MOTOR 3.3V REGULATOR F D 28 DEH-P8MP/XN/UC 1 2 3 4 WWW.PCBOOK.IR 5 6 7 8 A D-b D CD CORE UNIT(S10WMACODE2) B ! AND 1.5V REGULATOR SWITCHES: CD CORE UNIT(S10WMACODE2) S901 : HOME SWITCH.........ON-OFF S902 : CLAMP SWITCH.......ON-OFF S903 : DSCSNS SWITCH.....ON-OFF S904 : 12EJ SWITCH............ON-OFF S905 : 8EJ SWITCH..............ON-OFF The underlined indicates the switch position. C F T C S SIGNAL LINE FOCUS SERVO LINE TRACKING SERVO LINE CARRIAGE SERVO LINE SPINDLE SERVO LINE 16.934MHz A CN704 D Pull-down MICRO COMPUTER C906 R22 6 PE5423A E ^ 3.3V REGULATOR R01 A & 2R2 C910 470P C722 1 CN701 F D DEH-P8MP/XN/UC 5 6 7 8 29 E F 2 3 T T F F T F T # @ T T AND 1 F F T C F F A F T T F T F % 2 T T F C217 F T C C S S 1 T 30 F B R1 L209 D-b F PICKUP UNIT(P9.9MP3)(SERVICE) D-a A-a D-b 1 WWW.PCBOOK.IR 3 4 2 D D-a DEH-P8MP/XN/UC 4 5 6 C C 7 3.3V REGULATOR C C S S F F T T D-a A-a D-b 0 9 F T CD DRIVER 5 8 7 $ S C 4 3 S S F T WWW.PCBOOK.IR 6 M2 CXB8933 LOADING/CARRIAGE MOTOR M1 CXB6007 SPINDLE MOTOR 1 2 3 Pull-down 2 C 5 7 8 A 4 5 D-b 4.00MHz B C D E F D-a DEH-P8MP/XN/UC 8 31 C S S 32 D-b 1 B C 1 2 3 3 E DEH-P8MP/XN/UC 4 CN704 SIGNAL LINE FOCUS SERVO LINE TRACKING SERVO LINE CARRIAGE SERVO LINE SPINDLE SERVO LINE WWW.PCBOOK.IR A T C S F SWITCHES: CD CORE UNIT(S10WMACODE2) S901 : HOME SWITCH.........ON-OFF S902 : CLAMP SWITCH.......ON-OFF S903 : DSCSNS SWITCH.....ON-OFF S904 : 12EJ SWITCH............ON-OFF S905 : 8EJ SWITCH..............ON-OFF The underlined indicates the switch position. 2 16.934MHz 1.5V REGULATOR CD CORE UNIT(S10WMACODE2) D AND ! D D-a D-b 1 4 A F 2 6 Pull-down PE5423A MICRO COMPUTER C722 1 5 3 D-a D-b A 3.3V REGULATOR CN704 6 2R2 2 R22 C906 & ^ A WWW.PCBOOK.IR 6 4 7 CN701 5 7 8 A 470P B C D E F 5 D-b DEH-P8MP/XN/UC 8 33 R01 C910 WWW.PCBOOK.IR 1 2 - Waveforms 1 DSCSNS 2 8SNS 3 12SNS 4 LOEJ A 5V/div 5V/div 5V/div 5V/div 3 4 Note : 1. The encircled numbers denote measuring points in the circuit diagram. 2. Reference voltage REFO1(1.65V) 500ms/div 1 DSCSNS 5 CLCONT 4 LOEJ 6 VD 5V/div 5V/div 5V/div 10V/div 500ms/div 1 DSCSNS 2 8SNS 3 12SNS 4 LOEJ 5V/div 5V/div 5V/div 5V/div 12 cm CD Loading operation 12 cm CD Loading operation 8 cm CD Loading operation Ref.: GND Ref.: GND Ref.: GND Mode: Normal Mode: Normal Mode: Normal 500ms/div B 7 SIN 8 CIN 9 TIN C 2s/div 1V/div 500mV/div 500mV/div 7 SIN 8 CIN 9 TIN 7 SIN 8 CIN 9 TIN 1s/div 1V/div 500mV/div 500mV/div 2s/div 1V/div 500mV/div 500mV/div 12 cm CD-DA setup operation after loading 12 cm CD-ROM(1 session) setup operation after loading 12 cm CD-ROM(3 sessions) setup operation after loading Ref.: REFO Ref.: REFO Ref.: REFO Mode: Normal Mode: Normal Mode: Normal 0 FIN ! RFOK 7 SIN 200mV/div 500ms/div @ TE 2V/div # FE 2V/div 500mV/div 200ms/div # FE 500mV/div 0 FIN @ TE 9 TIN 12 cm CD-DA Source On setup operation Source On setup operation Ref.: REFO Ref.: REFO Ref.: REFO Mode: Normal Mode: Normal Mode: Normal 500mV/div 20ms/div 500mV/div 500mV/div 500mV/div CD-DA Play operation D # FE 0 FIN @ TE 9 TIN E 500mV/div 20ms/div 500mV/div 500mV/div 500mV/div $ MDX 7 SIN 1V/div 50ms/div 200mV/div $ MDX 7 SIN 2V/div 1V/div 5µs/div CD-ROM play operation(Regular track Jump) Spindle waveform during play operation Spindle waveform during play operation (Wider) Ref.: REFO Ref.: REFO Ref.: REFO Mode: Normal Mode: Normal Mode: Normal F 34 DEH-P8MP/XN/UC 1 2 3 4 WWW.PCBOOK.IR 5 0 FIN # FE 6 500mV/div 200ms/div @ TE 500mV/div % RFAGC 7 % RFAGC @ TE 9 TIN 500mV/div 2ms/div 500mV/div 8 1V/div 500µs/div 500mV/div 500mV/div Focus Search waveform Track Open waveform 1 Track Jump waveform Ref.: REFO Ref.: REFO Ref.: REFO Mode: TEST Mode: TEST Mode: TEST A B % RFAGC @ TE 9 TIN 500µs/div % RFAGC 1V/div 500mV/div @ TE 500mV/div 9 TIN % RFAGC @ TE 9 TIN 1ms/div 1V/div 500mV/div 500mV/div 2ms/div 1V/div 500mV/div 500mV/div 4 Tracks Jump waveform 10 Tracks Jump waveform 32 Tracks Jump waveform Ref.: REFO Ref.: REFO Ref.: REFO Mode: TEST Mode: TEST Mode: TEST % RFAGC @ TE 8 CIN 7 SIN 200ms/div ^ LOUT 1V/div 1V/div & ROUT 500mV/div 2V/div Search operation(Outter to Inner) 1V/div 1V/div 200µs/div 1 DSCSNS 2 8SNS 3 12SNS 4 LOEJ Analog audio waveform C 5V/div 5V/div 5V/div 5V/div 500ms/div 12 cm CD Eject operation D Ref.: REFO Ref.: AGND Ref.: GND Mode: Normal Mode: Normal Mode: Normal 1 DSCSNS 5V/div 5 CLCONT 5V/div 4 LOEJ 5V/div 500ms/div 1 DSCSNS 2 8SNS 3 12SNS 4 LOEJ 5V/div 5V/div 5V/div 5V/div 500ms/div 7 SIN 8 CIN 9 TIN 1V/div 500ms/div 500mV/div 500mV/div 12 cm CD Eject operation 8 cm CD Eject operation CD-DA >> CD-ROM mode change(Band key) Ref.: GND Ref.: GND Ref.: REFO Mode: Normal Mode: Normal Mode: Normal E F DEH-P8MP/XN/UC 5 6 7 8 35 WWW.PCBOOK.IR 1 7 SIN 8 CIN 9 TIN A 2 3 1V/div 500ms/div % RFAGC 500mV/div 9 TIN 500mV/div @ TE 0 FIN 1V/div 1V/div 1V/div 1V/div CD-ROM >> CD-DA mode change(Band key) Black dot(800µm) during play Ref.: REFO Ref.: REFO Mode: Normal Mode: Normal 4 500µs/div B C D E F 36 DEH-P8MP/XN/UC 1 2 3 4 5 WWW.PCBOOK.IR 6 7 8 A B C D E F DEH-P8MP/XN/UC 5 6 7 8 37 WWW.PCBOOK.IR 1 2 3 4 4. PCB CONNECTION DIAGRAM 4.1 TUNER AMP UNIT A NOTE FOR PCB DIAGRAMS 1.The parts mounted on this PCB include all necessary parts for several destination. For further information for respective destinations, be sure to check with the schematic diagram. 2.Viewpoint of PCB diagrams A CORD ASSY (POWER SUPPLY, SPEAKER) TUNER AMP UNIT Capacitor Connector SIDE A 18 17 16 14 12 10 8 6 15 13 11 9 7 5 4 3 2 1 B Chip Part P.C.Board SIDE B WIRED REMOTE CONTROL (DEH-P8MP/XN/UC, DEH-P80MP/XN/UC) C D E 2 1 C 4 3 6 5 8 10 12 14 16 18 7 9 11 13 15 17 CN1901 F A 38 FRONT DEH-P8MP/XN/UC 1 2 3 4 5 WWW.PCBOOK.IR 6 7 8 A CORD ASSY(PREOUT) SIDE A ANTENNA JACK PEAKER) IC,Q 6 4 2 11 9 5 3 1 7 473 FM/AM TUNER UNIT IP-BUS 12 10 8 2 61 5 11 10 9 8 B C D 60W/40W 40W 60W D CN902 E D CN901 M871 FLAP MOTOR B F A FRONT DEH-P8MP/XN/UC 5 6 7 8 39 WWW.PCBOOK.IR 1 A A 2 3 4 TUNER AMP UNIT IC,Q B C STEST1 D PCL1 E F A 40 DEH-P8MP/XN/UC 1 2 3 4 5 WWW.PCBOOK.IR 6 7 8 A SIDE B B C D E 1 F A DEH-P8MP/XN/UC 5 6 7 8 41 WWW.PCBOOK.IR 1 2 3 4 4.2 SWITCH UNIT A B SWITCH UNIT A CN871 B 1 2 3 CLOSE OPEN C D E F B 42 DEH-P8MP/XN/UC 1 2 3 4 WWW.PCBOOK.IR 5 6 7 8 4.3 KEYBOARD UNIT C SIDE A KEYBOARD UNIT A ADJ IC,Q OPEN RESET IC,Q SIDE B KEYBOARD UNIT EQ-EX OEL UNIT ENT EQ B BAND C TP5 TP6 4 6 10 8 1 9 7 3 5 2 VOL/SEL D A CN801 F SRC ATT DISP LIST E CLOCK C C DEH-P8MP/XN/UC 5 6 7 8 43 WWW.PCBOOK.IR 1 2 3 4 4.4 CD MECHANISM MODULE D A SIDE A CD CORE UNIT(S10WMACODE2) M2 LOADING /CARRIAGE MOTOR B M1 SPINDLE MOTOR A PICKUP UNIT(P9.9MP3)(SERVICE) C D CN701 HOME E A CN704 F D 44 DEH-P8MP/XN/UC 1 2 3 4 WWW.PCBOOK.IR 5 D 6 7 8 SIDE B CD CORE UNIT(S10WMACODE2) A 12EJ 8EJ DSCSNS B CLAMP C D E F D DEH-P8MP/XN/UC 5 6 7 8 45 1 WWW.PCBOOK.IR 2 3 4 5. ELECTRICAL PARTS LIST A Circuit Symbol and No. B Circuit Symbol and No. Part No. A Unit Number:CWM9287(P8MP/XN/UC) Unit Number:CWM9288(P80MP/XN/UC) Unit Number:CWM9289(P1Y/XN/ES) Unit Name:Tuner Amp Unit MISCELLANEOUS C D E IC 101 IC 131 IC 171 IC 201 IC 221 IC IC IC IC IC HA12240FP PML009A NJM4558MD PAL008A NJM2406F IC 241 IC 341 IC 451 IC 561 IC 601 IC IC IC IC IC UPC494GS PA2028A BA033FP TPD1018F PD5925A IC 652 IC 801 IC 841 IC 871 Q 101 IC IC IC IC Transistor BD4835G TC74VHCT125AFT NJM2360M BA6288FS UMF23N Q Q Q Q Q 201 202 221 241 242 Transistor Transistor Transistor Transistor Transistor DTC124EU DTC114EU 2SC3052-12 FKV550N FKV550N Q Q Q Q Q 243 244 246 247 248 Transistor Transistor Transistor Transistor Transistor 2SA933S DTC123EU 2SC1740S DTC143EU 2SC1740S Q 361 Chip Transistor HN1C03FU (P8MP/XN/UC,P1Y/XN/ES) Transistor UMH3N (P80MP/XN/UC) Q 362 Chip Transistor HN1C03FU (P8MP/XN/UC,P1Y/XN/ES) Transistor UMH3N (P80MP/XN/UC) Q 363 Chip Transistor HN1C03FU (P8MP/XN/UC,P1Y/XN/ES) F 46 Part No. Q 364 Transistor (P80MP/XN/UC) Transistor UMH3N UMD2N Q Q Q Q Q 501 651 741 742 743 Transistor Transistor Transistor Transistor Transistor 2SC4081 2SC3052-12 UMD2N 2SD2375 2SD1760F5 Q Q Q Q Q 744 821 822 831 841 Transistor Transistor Transistor Transistor Transistor UMD2N UMD2N 2SD1767 UMF23N UMD2N Q Q Q Q Q 842 861 871 872 881 Transistor Transistor Transistor Transistor Transistor 2SD1760F5 2SC3052-12 2SD1760F5 UMD3N UMH9N Q Q Q Q Q 882 883 884 885 901 Transistor Transistor Transistor Transistor Transistor 2SC4081 2SA1576 2SC4081 2SC4081 UMD2N Q Q Q Q Q 902 921 922 923 931 Transistor Transistor Transistor Transistor Transistor 2SD2375 2SD2375 2SB1243 DTC114EU UMX1N Q Q D D D 941 951 171 172 173 Transistor Transistor Diode Network Diode Network Diode DTC114EU 2SA1576 DA204U DA204U DAN202U D D D D D 174 221 222 241 242 Diode Diode Diode Diode Diode DAP202U UDZS6R2(B) UDZS6R8(B) FMG22 FMG22 D D D D D 243 244 245 246 321 Diode Diode Diode Diode Diode FMJ-2303 FMJ-2303 1SR154-400 1SS355 RB706F-40 D 341 D 361 D 451 Diode Diode Diode(P8MP/XN/UC,P1Y/XN/ES) 1SS396 1SS133 1SR154-400 DEH-P8MP/XN/UC 1 2 3 4 5 WWW.PCBOOK.IR Circuit Symbol and No. 6 Part No. D 501 D 502 Diode Diode DAN202U HZS9L(A2) D D D D D 561 562 741 742 801 Diode Diode Diode Diode Diode MPG06G-6415G50 MPG06G-6415G50 HZS9L(B1) HZS6L(C1) DAN202U D D D D D 802 803 804 805 806 Diode Diode Diode Diode Diode DAP202U DAP202U DAN202U DAP202U DAN202U D D D D D 807 808 821 841 842 Diode Diode Diode Diode Diode DAP202U DAN202U HZS11L(A1) HZS11L(A1) RB411D D D D D D 861 871 872 873 881 LED Diode Diode Diode Diode SML311BBT(PQ) HZS6L(C3) 1SS133 1SS133 DAN202U D D D D D 882 883 884 901 902 Diode Diode Diode Diode Diode DAN202U DAN202U DAN202U HZS6L(B2) MPG06G-6415G50 D D D D D 921 931 932 941 951 Diode Diode Diode Diode Diode HZS9L(B3) HZS7L(C3) HZS7L(A1) MPG06G-6415G50 DAN202U D 981 D 982 D 983 D 984 ZNR401 Diode Diode Diode Diode Surge Protector MPG06G-6415G50 MPG06G-6415G50 MPG06G-6415G50 MPG06G-6415G50 RCCA-201Q31UA-PI L L L L L 101 131 241 242 243 Inductor Inductor Coil Coil Ferri-Inductor LCTC2R2K1608 LCTA2R2J2520 CTH1310 CTH1310 LAU220K L L L L L 341 401 402 403 404 Ferri-Inductor Inductor Inductor Inductor Inductor LAU220K LAU1R0K LAU2R2K LAU1R0K LCTA4R7J2520 L L L L L 601 701 801 831 841 Ferri-Inductor Ferri-Inductor Inductor Ferri-Inductor Inductor LAU100K LAU100K CTF1379 LAU100K CTF1489 L L L X S 842 843 951 601 421 Inductor Chip-Inductor Chip-Inductor Radiator 10.00MHz Slide Switch(60W/40W) CTF1510 LCTA2R2J3225 LCTA2R2J3225 CSS1475 CSH1051 Semi-fixed 10kΩ(B) Fuse 3A > Microphone CCP1229 CEK1286 CPM1011 VR321 FU361 MIC321 7 Circuit Symbol and No. SP601 Buzzer FM/AM Tuner Unit 8 Part No. CPV1062 CWE1646 A RESISTORS R R R R R 101 102 103 104 105 RS1/16S102J RS1/16S223J RS1/16S181J RS1/16S222J RS1/16S181J R R R R R 106 107 108 109 110 RS1/16S223J RS1/16S102J RS1/16S150J RS1/16S562J RS1/16S332J R R R R R 111 112 113 114 131 RS1/16S470J RS1/16S101J RS1/16S102J RS1/16S101J RS1/16S821J R R R R R 132 133 134 135 136 RS1/16S821J RS1/16S102J RS1/16S102J RAB4C102J RS1/16S101J R R R R R 137 138 139 140 141 RS1/16S101J RS1/16S101J RS1/16S101J RS1/16S101J RS1/16S101J R R R R R 171 172 173 174 175 RS1/16S104J RS1/16S104J RS1/16S563J RS1/16S563J RS1/16S474J R R R R R 176 201 202 203 204 RS1/16S474J RS1/16S681J RS1/16S103J RS1/16S103J RS1/16S331J R R R R R 205 221 222 223 224 RS1/16S681J RS1/16S103J RS1/16S103J RS1/16S473J RS1/16S104J R R R R R 231 241 242 243 244 RS1/16S473J RS1/2PMF3R3J RS1/2PMF3R3J RD1/4MUF470J RD1/4MUF470J R R R R R 245 247 248 249 250 RS1/16S222J RS1/16S104J RS1/16S822J RS1/16S224J RS1/16S472J R R R R R 251 252 253 254 255 RS1/16S103J RS1/16S1002D RS1/16S1002D RS1/16S3902D RS1/16S3902D DEH-P8MP/XN/UC 5 6 7 8 B C D E F 47 1 Circuit Symbol and No. A B RS1/16S2R2J RS1/16S2R2J RS1/16S473J RS1/16S473J RS1/16S103J R R R R R 261 262 263 264 265 RS1/4SA331J RS1/4SA331J RS1/16S0R0J RS1/4SA151J RS1/16S332J R R R R R 266 267 268 269 321 RS1/16S332J RS1/16S152J RS1/4SA151J RS1/16S152J RS1/16S222J R R R R R 323 324 325 341 342 RS1/16S561J RS1/16S104J RS1/16S104J RS1/16S103J RS1/16S103J R 363 C R 364 R 365 R 366 R 367 R 368 R 369 R 370 R 371 R 372 F (P8MP/XN/UC,P1Y/XN/ES) (P80MP/XN/UC) (P8MP/XN/UC,P1Y/XN/ES) (P80MP/XN/UC) (P8MP/XN/UC,P1Y/XN/ES) (P80MP/XN/UC) RS1/16S820J RS1/16S821J RS1/16S820J RS1/16S821J RS1/16S820J RS1/16S821J (P8MP/XN/UC,P1Y/XN/ES) (P80MP/XN/UC) (P8MP/XN/UC,P1Y/XN/ES) (P80MP/XN/UC) (P8MP/XN/UC,P1Y/XN/ES) (P80MP/XN/UC) RS1/16S820J RS1/16S821J RS1/16S820J RS1/16S821J RS1/16S820J RS1/16S821J (P8MP/XN/UC,P1Y/XN/ES) (P80MP/XN/UC) (P8MP/XN/UC,P1Y/XN/ES) (P80MP/XN/UC) (P8MP/XN/UC,P1Y/XN/ES) (P80MP/XN/UC) RS1/16S103J RS1/16S0R0J RS1/16S103J RS1/16S0R0J RS1/16S103J RS1/16S0R0J (P8MP/XN/UC,P1Y/XN/ES) (P80MP/XN/UC) (P8MP/XN/UC,P1Y/XN/ES) (P80MP/XN/UC) (P8MP/XN/UC,P1Y/XN/ES) (P80MP/XN/UC) RS1/16S103J RS1/16S0R0J RS1/16S103J RS1/16S0R0J RS1/16S103J RS1/16S0R0J R R R R R 373 374 375 376 377 R R R R R 378 379 380 381 382 (P8MP/XN/UC,P1Y/XN/ES) (P8MP/XN/UC,P1Y/XN/ES) (P8MP/XN/UC,P1Y/XN/ES) (P8MP/XN/UC,P1Y/XN/ES) R R R R R 383 384 385 389 401 (P8MP/XN/UC,P1Y/XN/ES) RS1/16S471J (P8MP/XN/UC,P1Y/XN/ES) RS1/16S471J (P80MP/XN/UC) RS1/16S0R0J RS1/16S102J RS1/16S681J R 402 R 403 RS1/16S681J RS1/16S681J 48 3 Part No. 256 257 258 259 260 R 362 E 2 R R R R R R 361 D WWW.PCBOOK.IR RS1/16S223J RS1/16S223J RS1/16S223J RS1/16S223J RS1/16S223J RS1/16S223J RS1/16S471J RS1/16S471J RS1/16S471J RS1/16S471J Circuit Symbol and No. 4 Part No. R 404 R 405 R 406 RS1/16S681J RS1/16S681J RS1/16S681J R R R R R 421 422 451 501 502 RS1/16S104J RS1/16S102J RD1/4PU2R2J RS1/16S103J RS1/16S473J R R R R R 503 561 571 572 601 RS1/16S473J RS1/16S103J (P8MP/XN/UC,P80MP/XN/UC) RS1/16S102J (P8MP/XN/UC,P80MP/XN/UC) RS1/16S102J RS1/16S472J R R R R R 602 603 604 605 606 RS1/16S472J RS1/16S473J RS1/16S104J RS1/16S104J RS1/16S103J R R R R R 607 608 609 610 612 RS1/16S0R0J RS1/16S104J RS1/16S104J RS1/16S102J RS1/16S103J R R R R R 613 614 615 616 617 RS1/16S681J RS1/16S681J RS1/16S681J RS1/16S473J RS1/16S104J R R R R R 618 619 620 621 622 RS1/16S104J (P80MP/XN/UC) RS1/16S104J (P8MP/XN/UC,P1Y/XN/ES) RS1/16S104J RS1/16S104J R R R R R 623 624 625 626 627 RS1/16S104J RS1/16S104J RS1/16S0R0J RS1/16S0R0J RS1/16S0R0J R R R R R 628 629 630 631 642 RS1/16S0R0J RS1/16S0R0J RS1/16S0R0J RS1/16S104J RS1/16S104J R R R R R 651 652 653 654 655 RS1/16S102J RS1/16S102J RS1/16S183J RS1/16S473J RS1/16S222J R R R R R 701 703 704 705 706 RS1/16S473J RS1/16S682J RS1/16S682J RS1/16S682J RS1/16S682J R R R R R 707 708 709 710 711 RS1/16S221J RS1/16S221J RS1/16S221J RS1/16S221J RS1/16S221J R 712 RS1/16S221J (P1Y/XN/ES) (P8MP/XN/UC,P80MP/XN/UC) RS1/16S104J DEH-P8MP/XN/UC 1 2 3 4 5 WWW.PCBOOK.IR Circuit Symbol and No. 6 7 Part No. Circuit Symbol and No. 8 Part No. R 741 R 743 R 801 RD1/4PU391J RD1/4PU391J RS1/16S104J R 903 R 904 R 922 RS1/16S332J RS1/16S0R0J RS1/16S152J R R R R R 802 803 804 805 806 RS1/16S104J RS1/16S102J RS1/16S222J RS1/16S472J RS1/16S222J R R R R R 923 924 925 931 932 RD1/4PU152J RS1/16S223J RS1/16S472J RS1/16S104J RS1/16S473J R R R R R 807 808 809 810 811 RS1/16S222J RS1/16S222J RS1/16S222J RS1/16S222J RS1/16S0R0J R R R R R 933 934 935 943 951 RS1/16S103J RS1/16S473J RS1/16S472J RS1/16S103J RS1/16S102J R R R R R 812 813 815 816 818 RS1/16S104J RS1/16S102J RS1/16S104J RS1/16S221J RS1/16S103J R R R R R 952 953 954 955 981 RS1/16S472J RS1/16S472J RS1/16S153J RS1/16S104J RD1/4PU102J R R R R R 819 821 822 823 824 RS1/16S122J RS1/16S221J RS1/16S221J RS1/16S1R0J RS1/16S473J R 982 R 987 RS1/4SA0R0J RS1/16S0R0J R R R R R 825 826 827 831 832 RS1/16S473J RS1/16S473J RS1/16S104J RS1/16S472J RS1/16S102J C C C C C 102 103 104 131 132 CKSRYB104K16 CKSRYB102K50 CKSRYB102K50 CCSQCH222J50 CEAL1R0M50 R R R R R 833 841 842 844 845 RS1/16S472J RS1/16S331J RS1/16S331J RS1/16S1R0J RS1/16S391J C C C C C 133 134 135 136 137 CEAL1R0M50 CKSRYB104K16 CKSRYB104K16 CEAL1R0M50 CEAL1R0M50 R R R R R 846 847 848 861 862 RS1/16S121J RD1/4PU302J RD1/4PU302J RS1/16S331J RS1/16S331J C C C C C 138 139 140 141 142 CEAL1R0M50 CEAL1R0M50 CEJQ470M10 CKSRYB104K16 CCSQCH222J50 R R R R R 863 864 865 871 872 RS1/16S331J RS1/16S103J RS1/16S103J RAB4C102J RD1/4PU391J C C C C C 143 144 145 146 147 CEALNP4R7M16 CEALNP4R7M16 CEALNP4R7M16 CEALNP4R7M16 CCSQCH152J50 R R R R R 881 882 883 884 885 RS1/16S472J RS1/16S2203D RS1/16S3303D RS1/16S4702D RS1/16S223J C C C C C 148 149 150 151 152 CEALNP4R7M16 CEALNP4R7M16 CCSQCH152J50 CEALNP4R7M16 CEALNP4R7M16 R R R R R 886 887 888 889 890 RS1/16S223J RS1/16S3303D RS1/16S3303D RS1/16S1503D RS1/16S1503D C C C C C 159 160 161 171 172 CKSRYB474K10 CKSRYB474K10 CEJQ100M50 CKSRYB103K50 CKSRYB104K16 R R R R R 891 892 893 894 895 RS1/16S1503D RS1/16S1503D RS1/16S1503D RS1/16S1503D RS1/16S1503D C C C C C 173 174 175 176 177 CKSRYB104K16 CKSRYB104K16 CKSRYB104K16 CKSRYB474K10 CKSRYB474K10 R 896 R 902 RS1/16S1503D RS1/16S223J C 178 CCSRCH101J50 A CAPACITORS DEH-P8MP/XN/UC 5 6 B 7 8 C D E F 49 1 Circuit Symbol and No. A WWW.PCBOOK.IR 2 3 Part No. Circuit Symbol and No. (P8MP/XN/UC,P1Y/XN/ES) (P8MP/XN/UC,P1Y/XN/ES) (P8MP/XN/UC,P1Y/XN/ES) (P8MP/XN/UC,P1Y/XN/ES) 4 Part No. C C C C 179 201 202 203 CCSRCH101J50 CFTNA224J50 CFTNA224J50 CFTNA224J50 C C C C 369 370 371 372 CKSRYB222K50 CKSRYB222K50 CKSRYB222K50 CKSRYB222K50 C C C C C 204 205 206 207 208 CFTNA224J50 CEAL330M10 CEHAR100M16 CKSQYB225K10 CKSQYB225K10 C C C C C 373 401 402 403 404 CEAL220M35 CKSRYB103K50 CKSRYB103K50 CEJQ470M10 CKSRYB103K50 C C C C C 211 212 213 214 221 CKSRYB472K50 CKSRYB472K50 CKSRYB472K50 CKSRYB472K50 CKSRYB103K50 C C C C C 405 407 451 452 453 CEJQ101M10 CKSYB475K10 CKSRYB103K50 CKSRYB103K50 CEJQ220M25 C C C C C 222 223 241 242 243 CKSRYB104K25 CKSRYB104K25 CQMA332J50 CQMA332J50 CCH1594 C C C C C 454 455 456 561 562 CKSYB475K10 CKSRYB103K50 CKSYB475K10 CKSRYB104K25 CKSRYB473K25 C C C C C 244 245 246 247 249 CCH1594 CEHAZL102M16 CEHAZL102M16 CCSRCH270J50 CKSRYB222K50 C C C C C 601 602 603 604 606 CCSRCH180J50 CCSRCH220J50 CEAL470M16 CKSRYB103K50 CCSRCH470J50 C C C C C 250 251 252 253 254 CQMAQ102J50 CKSRYB332K50 CKSYB105K25 CKSYB105K25 CCSQCH222J50 C C C C C 652 653 702 741 742 CKSRYB105K10 CKSRYB104K16 CCH1438 CKSRYB473K16 CKSRYB102K50 C C C C C 255 256 257 259 321 CEJQ101M16 CKSRYB103K50 CKSRYB103K50 CEHAZL100M50 CEJQ100M50 C C C C C 743 744 745 801 821 CEJQ101M16 CKSRYB473K16 CEJQ101M10 CKSRYB473K16 CKSRYB473K25 C C C C C 322 323 341 342 343 CEJQ220M25 CEJQ100M50 CEAL4R7M35 CEJQ101M16 CASAQ3R3M16 C C C C C 832 833 834 841 842 CCSRCH101J50 CKSRYB473K50 CKSRYB105K10 CKSRYB104K16 CEAL470M16 C C C C C 344 345 346 347 348 CKSRYB105K10 CKSRYB105K10 CKSRYB105K10 CKSYB684K16 CKSRYB105K10 C C C C C 843 844 845 846 847 CEAL101M10 CKSRYB104K16 CCSRCH331J50 CKSRYB103K50 CEAL330M25 C C C C C 349 350 351 352 353 CKSRYB105K10 CKSRYB105K10 CEAL100M16 CKSQYB225K10 CEJQ330M25 C C C C C 848 849 861 873 874 C C C C C 354 355 356 361 362 CEJQ330M25 (P8MP/XN/UC,P1Y/XN/ES) CEJQ330M25 (P8MP/XN/UC,P1Y/XN/ES) CEJQ330M25 CEJQ100M50 CEJQ100M50 C C C C C 875 876 877 878 881 CEAT331M10 CKSRYB102K50 CCSRCH101J50 CCSRCH101J50 CKSRYB103K50 C C C C C 363 364 365 366 367 CEJQ100M50 CEJQ100M50 CEJQ100M50 CEJQ100M50 (P8MP/XN/UC,P1Y/XN/ES) CKSRYB222K50 C C C C C 882 883 884 885 886 CKSQYB105K16 CKSQYB474K25 CKSQYB474K25 CKSQYB474K25 CKSQYB474K25 C 368 (P8MP/XN/UC,P1Y/XN/ES) CKSRYB222K50 C 887 CKSQYB474K25 B C D E F 50 2200µF/25V 2200µF/25V 470µF/10V 4.7µF CEAL100M25 CCG1111 CKSRYB104K25 CKSRYB224K10 CKSRYB224K10 DEH-P8MP/XN/UC 1 2 3 4 5 WWW.PCBOOK.IR Circuit Symbol and No. 6 Part No. C C C C 888 889 890 901 CKSQYB474K25 CKSQYB474K25 CKSQYB474K25 CEJQ101M10 C C C C C 902 903 904 905 921 CKSRYB103K50 CKSRYB472K50 CCH1331 CCH1331 CEJQ221M10 C C C C C 922 923 924 931 941 470µF/16V 470µF/16V 470µF/16V C 951 C 981 CKSRYB103K50 CEJQ101M10 CCH1331 CKSRYB104K25 CKSQYB105K16 CKSRYB104K25 CKSRYB473K50 B Unit Number:CWS1389 Switch(CLOSE) Switch(OPEN) Circuit Symbol and No. 8 Part No. TH1981 X 1951 S 1901 S 1902 S 1903 Thermistor Ceramic Resonator 16MHz Push Switch Push Switch Switch(SEL/VOL) CCX1037 CSS1616 CSG1155 CSG1155 CSX1065 S S S S S Push Switch Push Switch Push Switch Push Switch Push Switch CSG1155 CSG1155 CSG1155 CSG1155 CSG1155 Push Switch Push Switch Push Switch Push Switch Semi-fixed 10kΩ(B) CSG1155 CSG1155 CSG1155 CSG1155 CCP1229 OEL Unit MXS8202 1921 1922 1923 1924 1925 S 1926 S 1927 S 1928 S 1929 VR1981 A B RESISTORS Unit Name:Switch Unit S 1 S 2 7 CSN1051 CSN1052 C Unit Number:CWM9290 Unit Name:Keyboard Unit MISCELLANEOUS R R R R R 1901 1902 1905 1906 1907 RS1/16S222J RS1/16S222J RS1/16S822J RS1/16S102J RS1/16S102J R R R R R 1908 1909 1910 1911 1912 RS1/16S222J RS1/16S332J RS1/16S822J RS1/16S473J RS1/16S154J IC 1941 IC 1951 IC 1952 IC 1953 Q 1951 IC IC IC IC Transistor S-818A33AUC-BGN PD5933A RS-140 PD6469A UMD2N R R R R R 1913 1914 1916 1921 1922 RS1/10S0R0J RS1/10S0R0J RS1/16S103J RS1/16S221J RS1/16S560J Q Q Q Q D 1952 1953 1981 1982 1901 Transistor Transistor Transistor Transistor Diode 2SC4154-11 UMD2N 2SC4617 2SD1664 DAP202U R R R R R 1923 1924 1925 1926 1927 RS1/16S221J RS1/16S560J RS1/16S221J RS1/16S560J RS1/16S221J D D D D D 1902 1921 1922 1923 1924 Diode LED LED LED LED DAN202U SML311BBT(PQ) SML311BBT(PQ) SML311BBT(PQ) SML311BBT(PQ) R R R R R 1928 1929 1930 1931 1932 RS1/16S560J RS1/16S221J RS1/16S560J RS1/16S221J RS1/16S560J D D D D D 1925 1926 1927 1928 1929 LED LED LED LED LED SML311BBT(PQ) SML311BBT(PQ) SML311BBT(PQ) SML311BBT(PQ) SML311BBT(PQ) R R R R R 1933 1934 1941 1951 1952 RS1/16S221J RS1/16S560J RS1/16S222J RS1/16S121J RS1/16S184J D D D D D 1930 1931 1932 1933 1934 LED LED LED LED LED SML311BBT(PQ) SML311BBT(PQ) SML311BBT(PQ) SML311BBT(PQ) SML311BBT(PQ) R R R R R 1953 1954 1955 1956 1957 RS1/16S2R2J RS1/16S154J RS1/16S473J RAB4C102J RS1/16S103J D D D L L 1951 1952 1953 1903 1941 Diode Diode Diode Inductor Inductor 1SS355 UDZS13(B) DAN202U CTF1530 CTF1530 R R R R R 1958 1959 1960 1961 1962 RAB4C473J RS1/16S473J RAB4C101J RAB4C101J RAB4C101J DEH-P8MP/XN/UC 5 6 7 8 C D E F 51 1 Circuit Symbol and No. A B C D E F WWW.PCBOOK.IR 2 3 Part No. R R R R R 1963 1964 1965 1966 1967 RAB4C101J RAB4C101J RAB4C101J RAB4C101J RAB4C101J R R R R R 1968 1969 1970 1971 1972 RAB4C101J RAB4C101J RAB4C102J RS1/16S102J RS1/16S0R0J R R R R R 1973 1974 1975 1977 1981 RS1/16S473J RS1/16S473J RS1/16S473J RS1/16S473J RS1/16S333J R R R R R 1982 1983 1984 1985 1986 RS1/16S683J RS1/16S393J RS1/16S392J RAB4C101J RS1/16S152J R 1988 R 1989 R 1991 RS1/16S101J RS1/16S101J RS1/16S104J Circuit Symbol and No. 4 Part No. Unit Number:CWX2952 Unit Name:CD CORE UNIT(S10WMACODE2) MISCELLANEOUS IC 201 IC 203 IC 301 IC 501 IC 701 IC IC IC IC IC UPD63761GJ NJM2391DL1-33 BA5835FM S-L2980A15MC-C6A PE5423A IC 703 Q 101 Q 601 Q 603 Q 701 IC Transistor Transistor Transistor Transistor S-812C33AUA-C2N 2SB1132 IMH20 2SB709A UN2111 D D L L L 101 601 203 207 209 Diode Diode Inductor Inductor Inductor 1SS355 MA152WA CTF1389 CTF1389 CTF1389 L X X S S 703 201 702 901 902 Inductor Resonator 4.00MHz Switch(HOME) Switch(CLAMP) CTF1389 CSS1603 CSS1654 CSN1051 CSN1051 Spring Switch(DSCSNS) Switch(12EJ) Switch(8EJ) CSN1052 CSN1051 CSN1051 Ceramic Resonator 16.934MHz CAPACITORS C C C C C 1905 1908 1909 1921 1922 CKSRYB104K25 CKSRYB104K25 CKSRYB104K25 CKSRYB104K25 CKSRYB104K25 C C C C C 1923 1924 1925 1926 1927 CKSRYB104K25 CKSRYB104K25 CKSRYB104K25 CKSRYB104K25 CKSRYB104K25 C C C C C 1928 1929 1930 1931 1932 CKSRYB104K25 CKSRYB104K25 CKSRYB104K25 CKSRYB104K25 CKSRYB104K25 C C C C C 1933 1934 1941 1942 1943 CKSRYB104K25 CKSRYB104K25 CSZSR4R7M16 CSZSR4R7M10 CKSQYB103K50 C C C C C 1944 1951 1952 1953 1954 CSZSR4R7M10 CKSYF106Z10 CKSRYB473K50 CKSRYB103K25 CKSRYB103K25 C C C C C 1955 1957 1981 1982 1983 CKSYF475Z16 CKSRYB103K25 CKSRYB104K25 CKSRYB104K25 CKSRYB104K25 C 1985 CKSRYB104K25 D 52 S 903 S 904 S 905 RESISTORS R R R R R 101 102 103 104 105 RS1/10S1R5J RS1/10S1R5J RS1/10S1R5J RS1/10S1R5J RS1/10S1R5J R R R R R 107 201 202 205 207 RS1/16SS0R0J RS1/16SS102J RS1/16SS333J RS1/16SS473J RS1/16SS473J R R R R R 209 214 216 218 220 RS1/16SS473J RS1/16SS472J RS1/16SS472J RS1/16SS472J RS1/16SS472J R R R R R 221 222 223 224 225 RS1/16SS103J RS1/16SS103J RS1/16SS0R0J RS1/16SS0R0J RS1/16SS103J R R R R R 226 227 228 229 231 RS1/16SS393J RS1/16SS562J RS1/16SS122J RS1/16SS472J RS1/16SS0R0J R R R R R 232 233 240 241 242 RS1/16SS122J RS1/16SS0R0J RS1/16SS0R0J RS1/16SS333J RS1/16SS0R0J DEH-P8MP/XN/UC 1 2 3 4 5 WWW.PCBOOK.IR Circuit Symbol and No. 6 7 Part No. Circuit Symbol and No. 8 Part No. R R R R R 243 245 250 256 261 RS1/16SS333J RS1/16SS333J RS1/16SS0R0J RS1/16SS0R0J RS1/16S0R0J R R R R R 750 754 755 756 765 RS1/16SS473J RS1/16SS102J RS1/16SS102J RS1/16SS104J RAB4CQ221J R R R R R 262 263 264 267 301 RS1/16S0R0J RS1/16S0R0J RS1/16S0R0J RS1/16S0R0J RS1/16SS183J R R R R R 769 773 777 778 779 RAB4CQ221J RAB4CQ221J RS1/16SS221J RS1/16SS221J RS1/16SS221J R R R R R 302 304 305 307 308 RS1/16SS822J RS1/16SS183J RS1/16SS822J RS1/16SS183J RS1/16SS183J R R R R R 901 902 905 906 908 RAB4CQ221J RS1/16S0R0J RS1/16SS221J RS1/16SS221J RS1/16SS0R0J R R R R R 309 310 501 601 602 RS1/16SS183J RS1/16SS183J RS1/16SS0R0J RS1/16S101J RS1/16S101J R 910 RS1/16SS0R0J R R R R R 603 604 605 606 701 RS1/16S223J RS1/16S223J RS1/16SS103J RS1/16S0R0J RS1/16S0R0J R R R R R 702 703 704 705 706 RS1/16SS0R0J RS1/16SS104J RS1/16SS104J RS1/16SS221J RS1/16SS221J R R R R R 707 708 709 710 711 RS1/16SS0R0J RS1/16SS221J RS1/16SS473J RS1/16SS102J RS1/16SS102J R R R R R 712 713 714 715 716 RS1/16SS102J RS1/16SS102J RS1/16SS473J RS1/16SS101J RS1/16SS472J R R R R R 717 718 719 720 721 RS1/16SS221J RS1/16SS221J RS1/16SS221J RS1/16SS471J RS1/16S0R0J R R R R R 724 725 726 727 729 RS1/16S473J RS1/16SS222J RS1/16SS103J RS1/16SS473J RS1/16SS223J R R R R R 730 731 732 733 735 RS1/16SS473J RS1/16SS104J RS1/16SS104J RS1/16SS104J RS1/16SS473J R R R R R 737 740 742 745 746 RS1/16SS104J RS1/16SS473J RS1/16SS104J RS1/16SS473J RS1/16SS104J 6 B CAPACITORS C C C C C 101 102 103 104 105 C C C C C 106 107 108 110 201 CCSSCH101J50 CKSRYB224K16 CKSSYB104K10 CKSSYB104K10 CKSSYB471K50 C C C C C 202 203 204 205 207 CKSSYB104K10 CKSSYB104K10 CCH1507 CKSSYB104K10 CCH1590 C C C C C 208 209 216 217 218 CKSSYB104K10 CKSSYB104K10 CKSSYB332K50 CKSSYB104K10 CKSSYB223K16 C C C C C 219 220 221 222 223 CKSSYB104K10 CKSSYB103K16 CKSSYB104K10 CCSSCH560J50 CCSSCH5R0C50 C C C C C 224 225 226 227 228 CKSSYB104K10 CKSSYB103K16 CCSSCH680J50 CCSSCH470J50 CKSSYB682K25 C C C C C 230 232 233 234 235 CKSSYB104K10 CKSSYB104K10 CCH1470 CCH1590 CKSRYB224K16 C C C C C 237 239 242 246 250 100µF/16V 47µF/6.3V 22µF/6.3V 220µF/4V 10µF/6.3V 220µF/4V CKSSYB104K10 CKSSYB104K10 CCH1504 CCH1506 CKSSYB104K10 C D E CKSSYB104K10 CCSSCH330J50 CKSSYB104K10 CKSSYB104K10 CKSRYB102K50 DEH-P8MP/XN/UC 5 A 7 8 F 53 1 Circuit Symbol and No. A B WWW.PCBOOK.IR 2 3 4 3 4 Part No. C C C C C 251 260 301 302 303 CKSRYB102K50 CKSSYB104K10 CKSSYB221K50 CKSSYB221K50 CKSSYB472K25 C C C C C 304 305 306 307 501 C C C C C 505 601 602 603 604 C C C C C 701 702 703 704 706 C C C C C 707 712 713 714 716 CKSSYB104K10 CKSRYB224K16 CKSSYB104K10 CKSSYB104K10 CKSSYB103K16 C C C C C 717 718 720 722 903 CCSSCH180J50 CCSSCH180J50 CKSQYB225K10 CKSRYB105K10 CKSSYB471K50 C 906 C 907 C 910 CKSRYB224K16 CKSSYB103K16 CKSQYB225K10 100µF/16V 4.7µF/25V 4.7µF/25V 4.7µF/25V CKSSYB103K16 CCH1504 CKSSYB104K10 CKSSYB104K10 CKSRYB224K16 CKSQYB475K6R3 CCSRCH102J50 CCSRCH102J50 CCH1568 CCH1568 CKSSYB104K10 CKSSYB471K50 CKSSYB103K16 CCH1592 CKSSYB104K10 C Miscellaneous Parts List D Pickup Unit(P9.9MP3)(Service) CXX1805 M 1 M 2 M 871 Motor Unit(SPINDLE) CXB6007 Motor Unit(LOADING/CARRIAGE) CXB8933 Motor Unit(FLAP) CXC2204 E F 54 DEH-P8MP/XN/UC 1 2 5 WWW.PCBOOK.IR 6 7 8 6. ADJUSTMENT 6.1 CONNECTION DIAGRAM A TUNER AMP UNIT CN801 B GGD1160 C GGD1378 KEYBOARD UNIT D CN1901 Rubber Band Rubber Band E F DEH-P8MP/XN/UC 5 6 7 8 55 WWW.PCBOOK.IR 1 2 3 4 6.2 OEL UNIT ADJUSTMENT A Adjustment point KEYBOARD UNIT (SIDE B) B C Digital Multi-Meter TP5 VR1981 TP6 D E <When the OEL Unit has been replaced> 1. Use VR1981 to adjust the resistance between TP5 and TP6 to 2.3 kΩ. F 56 DEH-P8MP/XN/UC 1 2 3 4 5 WWW.PCBOOK.IR 6 7 8 6.3 CD ADJUSTMENT 1) Cautions on adjustments • In this product the single voltage (3.3V) is used for the regulator. The reference voltage is the REFO1 (1.65V) instead of the GND. If you should mistakenly short the REFO1 with the GND during adjustment, accurate voltage will not be obtained, and the servo’s misoperation will apply excessive shock to the pickup. To avoid such problems: a. Do not mix up the REFO1 with the GND when connecting the (-) probe of measuring instruments. Especially on an oscilloscope, avoid connecting the (-) probe for CH1 to the GND. b. In many cases, measuring instruments have the same potential as that for the (-) probe. Be sure to set the measuring instruments to the floating state. c. If you have mistakenly connected the REFO1 to the GND, turn off the regulator or the power immediately. • Before mounting and removing filters or leads for adjustment, be sure to turn off the regulator. • For stable circuit operation, keep the mechanism operating for about one minute or more after the regulator is turned on. 2) Test mode This mode is used to adjust the CD mechanism module. • To enter the test mode. While pressing the LIST and EQ keys at the same time, reset. • To exit from the test mode. Turn off the ACC and back up. A Notes: a. During ejection, do not press any other keys than the EJECT key until the loaded disc is ejected. b. If you have pressed the (→) key or (←) key during focus search, turn off the power immediately to protect the actuator from damage caused by the lens stuck. c. For the TR jump modes except 100TR, the track jump operation will continue even if the key is released. d. For the CRG move and 100TR jump modes, the tracking loop will be closed at the same time when the key is released. e. When the power is turned off and on, the jump mode is reset to the single TR (91), the RF amp gain is set to 0dB, and the auto-adjustment values are reset to the default settings. B C • In the test mode, any software protections will not work. Avoid applying any mechanical or electrical shock to the mechanism during adjustment. • The RFI and RFO signals with a wide frequency range are easy to oscillate. When observing the signals, insert a resistor of 1k ohms in series. • The load and eject operation is not guarantied with the mechanism upside down. If the mechanism is blocked due to mistaken eject operation, reset the product or turn off and on the ACC to restore it. D E F DEH-P8MP/XN/UC 5 6 7 8 57 WWW.PCBOOK.IR 1 2 3 4 - Flow Chart [LIST]+[EQ]+Reset or [LIST]+[EQ]+BU+ACC [KEY] A Contents Test Mode In Display Key of the head unit Key of the remote control unit [CD]or[SOURCE] Source On TRK MIN SEC [3] [BAND] Power On [2] Power On (T.Offset is adjusted) (T.Offset is not adjusted) TRK 00 MIN00 SEC 00 TRK 99 MIN 99 SEC 99 [4] RF AMP *1 Gain switching SPINDLE *9 Speed switching TRK GGMIN GGSEC GG TRK SP MIN SP SEC SP B [BAND] [3] Power Off Focus Close S.Curve check TRK MIN SEC TRK [1] [→] Tracking Servo Close CRG+ [6] Focus Mode *2 switching TRK MIN SEC 0x 0x 0x 91 MIN91 SEC 91 00 MIN00 SEC00 99 MIN99 SEC99 [BAND] [1] [6] [3] T.Close and AGC T.Close RF AGC / MIN Applicable servomechanism Applicable servomechanism TRK MIN SEC SEC ?tr TRK ?min ?sec ?tr MIN SEC ?min ?sec CRG- TRK TRK Power Off TRK *3 TRK or [2] [←] *8 or 00 MIN00 SEC00 99 MIN99 SEC 99 TRK 00 MIN00 SEC00 99 MIN 99 SEC 99 TRK TRK ?? MIN?? SEC ?? [2] [→] [←] CRG+ CRG- T.Balance adjustment / TRK8x MIN8x SEC8x TRK8x MIN8x SEC8x TRK ?? MIN?? SEC ?? RF AGC coefficient display TRK ?? MIN ?? SEC ?? TRK or Automatic adjustment display switching *8 or TRK 9x MIN 9x SEC 9x or T.Balance coefficient display TRK 9x MIN 9x SEC 9x C [BAND] [1] Power Off F, T, RF AGC TRK MIN [3] *7 F.Bias display switching SEC TRK [6] F, T AGC / F.Bias RF AGC ?? MIN?? SEC ?? TRK ?tr MIN SEC ?min ?sec [→] CRG/TR Jump value switching TRK ?tr MIN [2] [←] *4 *5 CRG/TR Jump + SEC TRK ?min ?sec ?tr MIN SEC ?min ?sec *4 Tracking Open CRG/TR Jump TRK ?tr MIN SEC ?min ?sec TRK or 8x MIN8x SEC 8x 9xMIN 9xSEC 9x TRK *6 [BAND] [2] Power Off Tracking Open TRK MIN SEC TRK8x MIN8x SEC8x or TRK 9x MIN 9x SEC 9x D *1) → TYP TRK MIN SEC -6dB → TRK 06 MIN 06 SEC 06 -12dB Operation [Key] TRK 12 MIN 12 SEC 12 Test Mode *2) Focus Close → S.Curve ckeck setting TRK 00 MIN 00 SEC 00 (TRK 99 MIN 99 SEC 99) → TRK 01 MIN 01 SEC 01 F EQ measurement setting TRK 02 MIN 02 SEC 02 *3) F.Offset Display → T.Offset Display → Switch to the order of the original display E [BAND] Power On/Off *4) 1TR / 32TR / 100TR [→] CRG + / TR Jump + (Direction of the external surface) [←] CRG - / TR Jump (Direction of the internal surface) [1] T.CLS and AGC and Applicable servomechanism / AGC, AGC display switching [2] *5) Single TR → 32TR → 100TR → CRG Move 9x(8x) : 91(81) 92(82) 93(83) 94(84) RF Gain switching / Offset adjustment display / T.Balance adjustment / T.Open [3] F.Close, S.Curve / Rough Servo and RF AGC / F, T, RF AGC *6) Only at the time of CRG Move, 100TR Jump [4] SPDL 1X/2X switching As for the double speed (2x), audio output cannot be supported. [5] Error Rate measurement 1st-ON : ERR count beginning(30Sec) 2nd-ON : BER display data[%] [6] F. Mode switching / Tracking Close / CRG, TR Jump switching *7) TRK/MIN/SEC → F.AGC → T.AGC → F.Bias → RF AGC *8) CRG motor voltage = 2[V] *9) TYP(1X) TRK MIN → SEC 2X → TRK 22 MIN 22 SEC 22 1X TRK 11 MIN 11 SEC 11 As for the double speed (2x), audio output cannot be supported. TYP(2X) TRK MIN SEC → 1X TRK 11 MIN 11 SEC 11 → 2X TRK 22 MIN 22 SEC 22 F 58 DEH-P8MP/XN/UC 1 2 3 4 WWW.PCBOOK.IR 5 6 7 8 6.4 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT A • Note : The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the PU unit must be changed, the grating should be checked using the procedure below. • Purpose : To check that the grating is within an acceptable range when the PU unit is changed. • Symptoms of Mal-adjustment : If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform track search operations, or taking a long time for track searching. • Method : • Measuring Equipment • Measuring Points • Disc • Mode B • Oscilloscope, Two L.P.F. • E, F, REFO1 • TCD-782 • TEST MODE CD CORE UNIT(S10WMACODE2) C L.P.F. REFO1 E Xch 100kΩ F Oscilloscope 390pF VREF Ych 100kΩ 390pF VREF L.P.F. D F E • Checking Procedure 1. In test mode, load the disc and switch the 3V regulator on. 2. Using the → and ← buttons, move the PU unit to the innermost track. 3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjustment the display should now read "81". Press key 3. The display will change, returning to "81" on the fourth press. 4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase difference is within 75° . Refer to the photographs supplied to determine the phase angle. 5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is any improvement. If, after trying this a number of times, the grating angle does not become less than 75° then the mechanism should be judged to be at fault. • Note Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the average angle. • Hint Reloading the disc changes the clamp position and may decrease the "wobble". E F DEH-P8MP/XN/UC 5 6 7 8 59 1 WWW.PCBOOK.IR 2 3 4 Ech → Xch 20mV/div, AC Fch → Ych 20mV/div, AC Grating waveform A 0° 30° 45° 60° 75° 90° B C D E F 60 DEH-P8MP/XN/UC 1 2 3 4 WWW.PCBOOK.IR 5 6 7 8 6.5 ERROR MODE - Error Messages If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of the error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from the users and also for facilitating trouble analysis and repair work in servicing. A (1) Basic Indication Method 1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN (minutes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO remains in blank as before. 2) Head unit display examples Depending on display capability of LCD used, display will vary as shown below. xx contains the error number. 8-digit display ERROR–xx 6-digit display ERR–xx B 4-digit display E–xx (2) Error Code List Displayed error code Description of the code and potential cause(s) Code Class Electricity Carriage Home NG CRG can't be moved to inner diameter. 10 CRG can't be moved from inner diameter. SERVO LSI Com→ Failure on home switch or CRG move mechanism. munication Error C 11 Electricity Focus Servo NG Communication error between microcomputer and SERVO LSI. Focusing not available. → Stains on rear side of disc or excessive vibrations on REWRITABLE. 12 Electricity Spindle Lock NG Subcode NG Spindle not locked. Sub-code is strange (not readable). → Failure on spindle, stains or damages on disc, or excessive vibrations. 17 Electricity Setup NG A disc not containing CD-R data is found. Turned over disc are found, though rarely. CD signal error. AGC protection doesn't work. Focus can be easily lost. → Damages or stains on disc, or excessive vibrations on REWRITABLE. 30 Electricity Search Time Out Failed to reach target address. → CRG tracking error or damages on disc. 44 Electricity ALL Skip 50 Mechanism CD On Mech Error Skip setting for all track. (CD-R/RW) Mechanical error during CD ON. → Defective loading motor, mechanical lock and mechanical sensor. A0 System Power Supply NG D Power (VD) is ground faulted. → Failure on SW transistor or power supply (failure on connector). Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors). Unreadable TOC does not constitute an error. An intended operation continues in this case. Upper digits of an error code are subdivided as shown below: 1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors. E F DEH-P8MP/XN/UC 5 6 7 8 61 1 WWW.PCBOOK.IR 2 3 4 6.6 OEL SCREENSAVER STUDIO LKA TO LKD APPLICATION "OEL Screensaver Studio" is an application to create OEL display image file. The customer write the image file on a CD-R disc and install it to car audio. This function is similar to PC link-kit (CD-PC1). "OEL Screensaver Studio" is available to the public on the PIONEER Home Page. This software (GGV1169) is added LKA to LKD file conversion function to original "OEL Screensaver Studio". A - How to check: 1. Set up GGV1169 application. 2. Confirm the LKA file (ent_disp.lka) is converted to LKD file correctly or not. Please see a Readme.txt in the GGV1169 or help file of "OEL Screensaver Studio" for more information. B 6.7 SYSTEM MICROCOMPUTER TEST PROGRAM - PCL output In the normal operation mode (with the detachable panel installed, the ACC switched ON, the standby mode cancelled), shift the STEST1 (Pin 86) terminal to H. The clock signal is output from the PCL1 terminal (Pin 37). The frequency of the clock signal is 312.500kHz that is one 32nd of the fundamental frequency. The clock signal should be 312.500kHz ± 13Hz. If the clock signal is out of the range, the X'tal (X601) should be replaced with new one. C D E F 62 DEH-P8MP/XN/UC 1 2 3 4 5 WWW.PCBOOK.IR 6 7 8 7. GENERAL INFORMATION 7.1 DIAGNOSIS 7.1.1 DISASSEMBLY A - Removing the Case (not shown) 1. Remove the Case. CD Mechanism Module - Removing the CD Mechanism Module (Fig.1) 1 Remove the four screws. B Disconnect the connector and then remove the CD Mechanism Module. 1 1 C 1 1 Fig.1 - Removing the Grille Assy (Fig.2) 1 D Remove the four screws. Disconnect the connector and then remove the Grille Assy. 1 1 1 E 1 Grille Assy Fig.2 F DEH-P8MP/XN/UC 5 6 7 8 63 WWW.PCBOOK.IR 1 2 3 4 - Removing the Tuner Amp Unit (Fig.3) A 1 Remove the screw. 2 Remove the screw. 3 Straighten the tabs at three locations indicated. 4 2 1 4 Remove the screw and then remove the Tuner Amp Unit. B 3 3 C 3 Tuner Amp Unit - Removing the D242 and D244 (Fig.4) Fig.3 Tuner Amp Unit (SIDE A) Tuner Amp Unit (SIDE B) D 1 Remove the seven screws. 2 Remove the solder and then remove the D242 and D244. 2 1 D242 1 D244 2 1 1 1 1 1 E 2 Holder Fig.4 F 64 DEH-P8MP/XN/UC 1 2 3 4 5 WWW.PCBOOK.IR 6 7 8 Tweezers Tuner Amp Unit - Disconnecting the Flexible PCB (Fig.5) A 1 Release the two latches. Tweezers are inserted in the hole of Flexible PCB and Flexible PCB is removed from CN801. 1 1 B CN801 Fig.5 Flexible PCB - Service Precaution C On the internal surface of the Holder(CND2028), 2 types of spacers(CNM9141, CNM9142) are affixed for insulation with the OEL unit. When ordering parts to replace the Holder, please order the 2 types of spacers along with the Holder. Spacer (CNM9141) Holder (CND2028) Spacer (CNM9142) D Fig.6 When you attach Case(CNC8138) in Tuner Amp Unit, please attach in Tuner Amp Unit, without also forgetting Insulator(CNM6249). If you forget to attach Insulator in Tuner Amp Unit, there is a possibility that the DC/DC Converter Section may short-circuit. Case (CNC8138) Tuner Amp Unit E Insulator (CNM6249) DC/DC Converter Section Fig.7 F DEH-P8MP/XN/UC 5 6 7 8 65 1 WWW.PCBOOK.IR 2 3 4 - How to hold the Mechanism Unit 1. Hold the top and bottom frame. 2. Do not squeeze top frame's front portion too tight, because it is fragile. A B Do not squeeze. - Removing the Upper and Lower Frames 1. With a disc clamped, remove the four springs (A), the two springs (B), the two springs (C), and the four screws. 2. To remove the upper frame, open it on the fulcrum A. 3. While lifting the carriage mechanism, remove the three dampers. 4. With the frames removed, insert the connectors coming from the main unit and eject the disc. Caution: Before installing the carriage mechanism in the frames, be sure to apply some alcohol to the dampers and set the mechanism to the clamp mode. C A Upper Frame A C A A Carriage Mechanism B Damper Lower Frame D C A Damper B Damper E F 66 DEH-P8MP/XN/UC 1 2 3 4 5 WWW.PCBOOK.IR 6 7 8 - Removing the Pickup Unit 1. Apply shorting solder to the Pickup flexible cable. Disconnect the cable. 2. Set the mechanism to the clamp mode. 3. Remove the lead wires from the inner holder. 4. Remove the washer, styling holder, change arm, and pickup lock arm. 5. While releasing from the hook of the inner holder, lift the end of the feed screw. Caution: In assembling, move the planet gear to the load/eject position before setting the feed screw in the inner holder. A Shorting Solder B Washer C Pickup Lock Arm Change Arm Styling Holder Feed Screw D E Inner Holder Planet Gear F DEH-P8MP/XN/UC 5 6 7 8 67 E 68 1 6 2 3 2 3 4 4 6 8 10 12 5 7 9 11 5 6 9 11 13 8 10 12 14 7 1. RR+ 2. FL+ 3. RR4. FL5. FR+ 6. RL+ 7. FR8. RL9. ACC(SENSE) 4 1 3 2 18 17 10. NC 11. B.REMOTE 12. NC 13. ILL 14. MUTE 15. BACKUP 16. GND 17. ACC 18. GND 16 15 3 1. FL OUTPUT 2. GND 3. FR OUTPUT 4. GND 5. RL OUTPUT 6. GND 7. RR OUTPUT 8. GND 9. SWL OUTPUT 10. GND 11. SWR OUTPUT 12. GND 2 1 3 B 7 9 10 11 2 1 8 WWW.PCBOOK.IR 1. BUS+ 2. GND 3. GND 4. NC 5. BUS6. GND 7. BUS L+ INPUT 8. ASENB 9. BUS R+ INPUT 10. BUS R- INPUT 11. BUS L- INPUT 5 WIRED REMOTE CONTROL (DEH-P8MP/XN/UC,DEH-P80MP/XN/UC) FM/AM ANTENNA 1 4 7.1.2 CONNECTOR FUNCTION DESCRIPTION A C D F DEH-P8MP/XN/UC 4 WWW.PCBOOK.IR 5 6 7 8 7.2 IC PD5933A PD6469A PE5423A UPD63761GJ PD5925A HA12240FP UPC494GS PAL008A S-812C33AUA-C2N BA5835FM S-L2980A15MC-C6A A - Pin Functions(PD5925A) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35, 36 37 38 39 40 41 42 43 44 45 46 47 48,49 50 51 52 53 54 55 56 Pin Name SYSPW ICERROR ACCMON SEL60W NC BYTE CNVSS TELIN NC reset XOUT VSS XIN VDD nmi NC NC NC RX2 OELPW NC PEE NC brst brxen bsrq RX TX BSO BSI BSCK NC DPDT KYDT ROT1, 0 PCL SWVDD NC FLPILM ILMPW ejtin gdtc1 NC NC NC gdtc2 NC fopnsw fclssw FLPCLS FLPOPN FLPPW RECEIVE CSENSOUT I/O O I O I I I O I I O O O I/O I I O O I O O I I O O O O I O O I I O O O O O Function and Operation System power control output Power IC error sense input ACC monitor output Power amp 60W/40W select input Not used External data bus width change input Processor mode change input Telephone mute input Not used Reset input Clock output GND Clock input Power supply input Not used Not used Not used Not used IP-BUS : Data input 2 OEL power supply output Not used PEE sound output Not used P-BUS : Reset output P-BUS : Reception enable input / output P-BUS : Service request input IP-BUS : Data input IP-BUS : Data output P-BUS : Data output P-BUS : Data input P-BUS : Clock output Not used Display data output Key data input Rotary encoder pulse input1, 0 Output for clock adjustment GRILLE : Chip enable output Not used Inside of flap illumination output Illumination output Eject key input Picture rewriting output 1 Not used Not used Not used Picture rewriting output 2 Not used Flap open sense input Flap close sense input Flap motor close output Flap motor open output Flap motor driver power ON/OFF output Not used Flap open/close output B C D E F DEH-P8MP/XN/UC 5 6 7 8 69 WWW.PCBOOK.IR 1 Pin No. 57 58,59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82,83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 A B C D 2 Pin Name EMUTE NC VDD NC VSS NC KEYD PADA PACK DALMON NC tunpce@ TUNPCE1 ROMCS asens bsens ROMCK ROMDATA VST VDT VCK IPPW ASENBO isens MODEL1,0 SYSPW2 MUTE TESTIN CROSSKEY ddchk KEYAD LVLINR DSENS LVLINL ASLIN AVSS SL VREF AVCC TUNPDI TUNPDO TUNPCK I/O O I I I/O O O O O I I O I/O O O O O O I I O O I I I I I I I I I I O O 3 Function and Operation Electronic volume : Mute output Not used Power supply input Not used GND Not used Wired remote control input Power amp : Data input Power amp : Clock input / output For consumption current reduction output Not used TUNER : Chip enable output(EEPROM) TUNER : Chip enable output(PLL) ROM correction chip select output ACC sense input Back up sense input ROM correction clock output ROM correction data input/output Electronic volume : Strobe output Electronic volume : Data output Electronic volume : Clock output IPBUS : Driver power supply control output IPBUS : Slave ACC sense output Illumination sense input Model select input Power IC power control output System mute output Test program input Cross key data input Temperature sense input for power amp DC/DC converter Wired remote control input Level indicator R channel input Flap close sense input Level indicator L channel input ASL input A/D converter power supply terminal TUNER : Signal level input A/D converter reference voltage A/D converter power supply input terminal TUNER : PLL communication data input TUNER : Data output(PLL) TUNER : Clock output(PLL) * PD5925A 25 4 HA12240FP 1 STB 100 26 8 VCC BUS+ BUS- 7 6 5 E BIAS - 76 51 RECEIVER OUTPUT 75 IC's marked by * are MOS type. Be careful in handling them because they are very liable to be damaged by electrostatic induction. F 70 COM - 50 DRIVER OUTPUT + + 1 2 3 4 S1 R S2 GND DEH-P8MP/XN/UC 1 2 3 4 WWW.PCBOOK.IR 5 6 7 8 UPC494GS - Pin Layout A Non-Inv.Input 1 16 Non-Inv.Input Inv.Input 2 15 Inv.Input Feed-Back 3 14 Ref Out Dead-Time Control 4 13 Output Control CT 5 12 VCC RT 6 11 C2 GND 7 10 E2 C1 8 9 B E1 C - Block Diagram 13 Output Control VCC 12 Ref Out 14 Reference Low Voltage Step Regulator GND 7 F T / F RT 6 Oscillator Dead-Time 4 Control Non-lnv.Input 1 lnv.Input 2 Non-lnv.Input 16 lnv.Input 15 + + - 9 E1 11 C2 CT 5 10 E2 Dead-Time Comparator + - D 8 C1 + - EA I E PWM Comparator EA II Feed-Back 3 F DEH-P8MP/XN/UC 5 6 7 8 71 WWW.PCBOOK.IR 1 2 3 4 PAL008A - Pin Layout A 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 MUTE DATA PW GND CH3 OUT3CK OUT3+ VCC2 OUT4PW GND CH4 OUT4+ AC-GND IN4 IN3 S.GND IN2 IN1 SVR OUT1+ PW GND CH1 OUT1VCC1 OUT2+ CCGND OUT2PW GND CH2 MG1 TAB B - Block Diagram MG1 2 VCC1 7 D/D conv. contoroller VCC2 21 Vcc1 Vcc2 5 CCGND offset Detection DATA 26 C CK 23 STEP-UP HE/STD SW Mute STBY AC-GND 17 IN1 12 + - 10 OUT1+ 8 OUT19 PW GND CH1 Short Circuit Protection D + IN2 13 6 OUT2+ 4 OUT2- Short Circuit Protection IN3 15 3 PW GND CH2 + - 22 OUT3+ 24 OUT325 PW GND CH3 Short Circuit Protection E + IN4 16 18 OUT4+ 20 OUT4- Short Circuit Protection 19 PW GND CH4 S.GND 14 11 SVR 17 AC-GND 1 TAB F 72 DEH-P8MP/XN/UC 1 2 3 4 WWW.PCBOOK.IR 5 6 7 8 - Pin Functions(PD5933A) Pin No. 1-4 5 6 7 8,9 10 11 12 13 14 15 16-18 19 20 21-23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40,41 42 43 44 45-48 49 50 51-59 60 61 62 63-69 70 71-86 87-89 90-92 93 94 95 96 97 98 99-100 Pin Name NC REM BYTE CNVSS NC reset XOUT VSS XIN VDD nmi kd!-kd# NC CKC NC LS NC CKD DPDT KYDT D1_L NC CLK1 NC D0_L NC CLK0 NC rdy NC hold NC rd NC wr cs#-cs0 A19 NC A17-A9 VDD A8 VSS A7-A1 NC D15-D0 ks!-ks# NC flstby AVSS fl!@on VREF AVCC flstby NC I/O O I I I I O I I O O O I O O I O I O I O O O O O O O I/O O O O Function and Operation Not used Remote control reception input GND connection Processor select input Not used Reset input Clock output GND Clock input Power supply input Not used Key data input Not used Cathode driver pulse output Not used Line synchronous signal output Not used Data transfer and driver clock output Display data input Key data output Display data MSB output Not used UART1 clock input Not used Display data LSB output Not used UART0 clock input Not used Not used Pull up Not used Hold input Not used Read strobe output Not used Not used OPEN External ROM chip select output Address bus 19 output Not used Address bus 17-9 output Power supply input Address bus 8 output GND connection Address bus 7-1 output Not used Data bus 15-0 input / output Key strobe output Not used Not used GND connection Not used OPEN GND connection VCC connection Not used OPEN Not used A B C D E F DEH-P8MP/XN/UC 5 6 7 8 73 WWW.PCBOOK.IR 1 2 3 4 * PD5933A A 100 76 1 75 25 51 B 26 * PD6469A 50 C D E A15 1 48 A16 A14 2 47 byte A13 3 46 VSS A12 4 45 DQ15/A-1 A11 5 44 DQ7 A10 6 43 DQ14 A9 7 42 DQ6 A8 8 41 DQ13 A19 9 40 DQ5 NC 10 39 DQ12 we 11 38 DQ4 reset 12 37 VCC NC 13 36 DQ11 NC 14 35 DQ3 RY/by 15 34 DQ10 A18 16 33 DQ2 A17 17 32 DQ9 A7 18 31 DQ1 A6 19 30 DQ8 A5 20 29 DQ0 A4 21 28 oe A3 22 27 VSS A2 23 26 ce A1 21 25 A0 A-1A0-A19 DQ0-DQ15 ce oe we RY/by byte AVCC VSS : Address input : Data input / output : Chip enable input : Output enable input : Write enable input : Ready/Busy output : 8 bit / 16 bit select input : Power supply : GND F 74 DEH-P8MP/XN/UC 1 2 3 4 WWW.PCBOOK.IR 5 6 7 8 - Pin Functions(PE5423A) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Pin Name AVREF AVSS RFOK CLAMP EVDD PWM NC IC/FLMD0 VDD REGC VSS X1 X2 reset XT1 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35, 36 37 38 39-42 43 44 45 46 47 48 49 50 51 52 53 54 55 56-58 59 60 61 62 63 64 65 XT2 PULLDOWN ejsw xint NC brst BSI BSO bsck FTXD FRXD BRXEN bsrq dspok DSCSNS(S903) 8EJ(S905) 12EJ(S904) EVSS EVDD SRAMLEVEL0, 1 EMPH emph NC adena LRCKOK SRAMLEVEL2 CD3VON CONT xrst VDCONT ROMDATA ROMCS ROMCK LOEJ CLCONT CDMUTE INT xcs NC xwait CLKOUT LOCK NC xwrite I/O Format O I C I I I I I I I I O I/O O I I/O I/O I I I I C /C C /C /C O O O C C C O O O O O O O I/O O O O O O C C C C C C C /C C C C C C O C I O I C O Function and Operation A power supply Positive power supply(5V) A power supply GND Output of state of RFOK CLAMP SW sense input E power supply Positive power supply For changer(PWM) Not used IC : VSS direct connection/FLMOD0 : Pull-down Positive power supply(5V) Connected to the capacity stabilizing output of the regulator GND Oscillator connection for mainclock Oscillator connection for mainclock System reset input Connected to the oscillator for subclock (connected to VSS via the resistor) Connected to the oscillator for subclock(Open) Connected to EVDD or EVSS via the resistor Eject key input CD LSI interruption signal input Not used P-Bus reset input P-Bus serial data input P-Bus serial data output P-Bus serial clock input/output For flash rewriting(transmitted signal) For flash rewriting(received signal) It is possible to receive P-Bus P-Bus service request demand DSP microcomputer initialization OK input Disc state sense input Input of detection of 8 cm disc ejection Input of detection of 12 cm disc ejection E power supply GND E power supply Positive power supply SRAM level meter output Emphasis information output Emphasis information output Not used A/D reference voltage supply control output (DOUT mute output) SRAM level meter output CD +3.3V power supply control output Servo driver power supply control output CD LSI reset control output VD power supply control output E2PROM data input/output E2PROM chip selection output E2PROM clock output The direction change output of LOAD/EJECT Driver input change output CD mute control output For changer(Interruption at the edge) CD LSI chip selection output Not used CD LSI write control signal output Internal system clock output(Open) Spindle lock input Not used CD LSI write control signal output DEH-P8MP/XN/UC 5 6 7 8 A B C D E F 75 WWW.PCBOOK.IR 1 Pin No. 66 67 68 69 70 71-86 87-90 91-93 94 95 96 97 98 99 100 A B 2 Pin Name NC xread XASTB BVSS BVDD AD0-15 NC A/D csens TYPE_A/D testin HOME TEMP VDSENS NC I/O 3 Format O O I/O /C I I I I 4 Function and Operation Not used CD LSI read control signal output CD LSI address strobe output B power supply GND B power supply Positive power supply Address/data Bus 0-15 Not used For changer(A/D) Flap closing sense input CD-DA analog/digital output change setup Chip check test program starting input Home SW sense input Temperature information sense input VD power supply short sense input Not used Format C 51 75 * PE5423A 76 50 100 26 Meaning CMOS 25 1 C D E F 76 DEH-P8MP/XN/UC 1 2 3 4 WWW.PCBOOK.IR 5 6 7 8 - Pin Functions(UPD63761GJ) Pin No. 1 2 3 4-8 9-16 17 18 19 20 21 22 23, 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39-41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73-88 89-99 Pin Name D.VDD D1.GND reset AB12-8 AD7-0 cs ASTB read write wait INTQ IFMODE0, 1 D1.VDD DA.VDD ROUT DA.GND REGC DA.GND LOUT DA.VDD X.VDD XTAL xtal X.GND VDDREG15 PWMSW0 TEST3-1 PWMSW1 TESTEN D1.GND DIN DOUT SCKIN SCKO LRCKIN LRCK xtalen D1.VDD RFCK/HOLD WFCK/MIRR PLCK LOCK/RFOK C1D1/C8M C1D2/C16M C2D1/RMUTE C2D2/LMUTE C2D3/SHOCK D1.GND C33M (rcs) RA11 (CKE) ras cas)(LDQM) cas!(UDQM) we oe(cas) D.GND RDB0-15 RA0-10 I/O I I I/O I I I I O O I O O I O I I I I I O I O I O I O O O O O O O O O O O O O O O O O O I/O O Function and Operation Power supply for digital circuits GND for 1.6V digital circuits Input of reset Address bus 12-8 from the microcomputer Address/data bus 7-0 to the microcomputer Chip selection Address strobe Control signals(read) Control signals(write) Control signals(wait) Interruption signals to the external microcomputer Switching the microcomputer I/F 0, 1 Power supply for 1.6V digital circuits Power supply for DAC Output of audio for the right channel GND for DAC Connected to the capacitor for band gap GND for DAC Output of audio for the left channel Power supply for DAC Power supply for the crystal oscillator Connected to the crystal oscillator(16.9344MHz) Connected to the crystal oscillator(16.9344MHz) Ground for the crystal oscillator Control of 1.6V regulator Setup 0 for PWM output(SD, MD) Connected to GND Setup 1 for PWM output(FD, TD) Connected to GND GND for 1.6V digital circuits Input of audio data Output of audio data Clock input for audio data Clock output for audio data Input of LRCK for audio data Output LRCK for audio data Permission to oscillate 16.9344MHz Power supply for 1.6V digital circuits Output of RFCK/HOLD signal Output of WFCK/MIRR signal Output of PLCK Output of LRCK/Output of RFOK Information on error correction/C8M : 8MHz Information on error correction/C16M : 16MHz Information on error correction/Mute for Rch Information on error correction/Mute for Lch Information on error correction/Detection of vibration GND for 1.6V digital circuits Output of 33.8688MHz(CLK for SDRAM) DRAM cs Output of DRAM address 11 Output of DRAM CKE Output of DRAM ras Output of DRAM lower cas(LDQM) Output of DRAM upper cas(UDQM) Output of DRAM we Output of DRAM oe(cas) Ground for digital circuits Input/output of DRAM data0-15 Output of DRAM address0-10 A B C D E F DEH-P8MP/XN/UC 5 6 7 8 77 WWW.PCBOOK.IR 1 2 Pin No. 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120, 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 A B C D Pin Name D.VDD FD+ FDTD+ TDSD+ SDMD+ MDREFOUTSV AD.VDD EFM ASY ATEST RFI AD.GND AGCO C3T AGCI RFO EQ2, 1 RF2RFA.GND A C B D F E VREFIN A.VDD REFOUT REFC FEFEO ADIN TETEO TE2 TEC LD PD D.GND I/O 3 Function and Operation Power supply for digital circuits Output of focus drive PWM + Output of focus drive PWM Output of tracking drive PWM + Output of tracking drive PWM Output of thread drive PWM + Output of thread drive PWM Output of spindle drive PWM + Output of spindle drive PWM REFOUT for servo Power supply for ADC Output of EFM signals Input of asymmetry Analog tests Input of RF Ground for the analog system Output of RF Connection to the capacitor for detecting 3T Input of AGC Output of RF(AGC) Equalizer 2, 1 Reversal input of RF2 Reversal input of RF Ground for the analog system Input of A Input of C Input of B Input of D Input of F Input of E Input of reference voltage Power supply for the analog system Output of reference voltage Connected to the capacitor for output of REFOUT Reversal input of FE Output of FE Input of FE, TE A/D converter Reversal input of TE Output of TE TE2 TEC Output of LD Input of PD Ground for digital circuits O O O O O O O O O O I O I O O I O I I I I I I I I I I O I I O I I O O I O I * S-812C33AUA-C2N 73 108 * UPD63761GJ E 4 72 109 1 78 3 VOUT 36 37 F 2 VIN 144 1 VSS Reference Voltage DEH-P8MP/XN/UC 1 2 3 4 WWW.PCBOOK.IR 5 6 7 8 - Pin Functions(BA5835FM) Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Pin Name VR OPIN2(+) OPIN2(-) OPOUT2 OPIN1(+) OPIN1(-) OPOUT1 GND MUTE POWVCC1 VO1(-) VO1(+) VO2(-) VO2(+) VO3(+) VO3(-) VO4(+) VO4(-) POWVCC2 GND CNT LDIN OPOUTSL OPINLSL OPOUT3 OPIN3(-) OPIN3(+) PREVCC Function and Operation Input pin for reference voltage Input pin for non-inverting input for CH2 preamplifier Input pin for inverting input for CH2 preamplifier Output pin for CH2 preamplifier Input pin for non-inverting input for CH1 preamplifier Input pin for inverting input from CH1 preamplifier Output pin for CH1 preamplifier Ground pin Mute control pin Power supply pin for CH1, CH2, and CH3 at "Power" stage Driver CH1 - Negative output Driver CH2 - Positive output Driver CH2 - Negative output Driver CH2 - Positive output Driver CH2 - Positive output Driver CH2 - Negative output Driver CH4 - Positive output Driver CH4 - Negative output Power supply pin for CH4 at "Power" stage Ground pin Control pin Loading input Output pin for preamplifier for thread Input pin for preamplifier for thread CH3 preamplifier output pin Input pin for inverting input for CH3 preamplifier Input pin for non-inverting input for CH3 preamplifier PreVcc A B C BA5835FM 14 1 15 28 D * S-L2980A15MC-C6A VOUT NC 5 4 + - E Reference voltage ON/OFF circuit 1 2 VIN VSS 3 ON/OFF F DEH-P8MP/XN/UC 5 6 7 8 79 WWW.PCBOOK.IR 1 2 3 4 - FM/AM Tuner Unit A OSC AM ANT 1 NC NC NC 18 19 20 21 NC 14 DO 11 NC DI 5V CK SL IC 3 EEPROM 5.0V 10 9 8 CE1 5 ROM_VDD CE2 WC 13 IC 5 3.3V ← 7 6 LPF FMRF ATT Rch 3 IC 1 3.3V FM ANT ATT FMRF B ANT adj 24 IC 2 2.5V Lch MIXER, IF AMP 23 DET, FM MPX RF adj T51 CF52 No. Symbol 1 AMANT C 2 3 4 5 6 7 D E RFGND FMANT VCC SL CE2 WC AUDIOGND NC 15 22 16 I/O Explain I AM antenna input I O I I 8 9 10 11 12 13 CE1 CK DI NC OSCGND ROM_VDD I I I 14 15 16 17 18 19 20 21 22 23 24 DO O DGND NC VDD_3.3 NC NC NC NC AUDIOGND L ch O R ch O RF ground FM antenna input power supply signal level chip enable-2 write control chip enable-1 clock data in non connection osc ground power supply data out digital ground non connection power supply non connection non connection non connection non connection audio ground L channel output R channel output 4 VDD_3.3 DGND 12 VCC OSCGND 2 3.3V IC 4 3.3V 2.5V 2.5V ← RFGND CF51 17 AM antenna input high impedance AMANT pin is connected with an all antenna by way of 4.7µH. (LAU type inductor) A series circuit including an inductor and a resistor is connected with RF ground for the countermeasure against the hum of power transmission line. Ground of antenna block Input of FM antenna 75Ω Surge absorber(DSP-201M-S00B) is necessary. The power supply for analog block. D.C 8.4V ± 0.3V Output of FM/AM signals level Chip enable for EEPROM ”Low” active You can write EEPROM, when EEPROM write control is “Low”. Ordinary non connection Chip enable for AF•RF ”High” active Clock Data input Not used Ground of oscillator block Power supply for EEPROM pin 13 is connected with a power supply of micro computer. Data output Ground of digital block Not used The power supply for digital block. 3.3V ± 0.2V Not used Not used Not used Not used Ground of audio block FM stereo “L-ch” signal output or AM audio output FM stereo “R-ch” signal output or AM audio output F 80 DEH-P8MP/XN/UC 1 2 3 4 WWW.PCBOOK.IR 5 6 7 8 7.3 EXPLANATION 7.3.1 OPERATIONAL FLOW CHART Power ON A VDD=5V Pin 14,60 bsens Pin 73 B bsens=L asens Pin 72 asens=L DSENS Pin 91 1.5V < DSENS < 4.5V C ASENBO←H Pin 80 Starts communication with Grille microcomputer. 300ms SWVDD←H Pin 38 300ms D In case of the above signal, the communication with Grille microcomputer may fail. If the time interval is not 300msec, the oscillator may be defective. Source keys operative Source ON E SYSPW←H Pin 1 Completes power-on operation. (After that, proceed to each source operation) F DEH-P8MP/XN/UC 5 6 7 8 81 WWW.PCBOOK.IR 1 2 3 4 7.3.2 CIRCUIT DESCRIPTIONS - Power Amp Secsion VCC2(CH3,4) 17.5V VCC1(CH1,2) 17.5V A IC201 PAL008A MOSFET60 4CH POWER AMP DC/DC CONVERTER DRIVER 14.4V DC/DC CONVERTER 1 for BACKUP BACKUP 10A B 14.4V DC/DC CONVERTER 2 for ACC ACC 10A IC241 UPC494GS DRIVER GND IC201 incorporates a 4channel power amplifier and a DC/DC converter driver. Current for channels 1 and 2 is supplied from the BACKUP power supply and current for channels 3 and 4 from the ACC power supply. This is because when current is supplied with voltage increase in the BACKUP power supply as it is done conventionally, 10A which is the limit to the vehicle fuse is exceeded. Thus ACC power supply was enabled to supply current so that there are two power supplies of BACUP and ACC and output of 60W x 4channel is expressed. Increased voltage (VCC1, VCC2) is controlled individually by separate DC/DC converters. Therefore, different voltages occur when there is difference between the outputs from L channel and R channel. A diode was hence connected between VCC1 and VCC2 so that voltage difference will not occur. C - DC/DC converter 1 D Power AMP IC201 PAL008A VCC1 VOLTAGE DIVIDER ERROR AMP DC/DC CONVERTOR 1 COMPARATOR REFERENCE VOLTAGE PULSE OUTPUT VOLTAGE BOOSTER TRIANGULAR WAVE OSCILLATOR RECTIFICATION CIRCUIT BATTERY VOLTAGE E Only one DC/DC converter driver is incorporated in IC201. Therefore, another DC/DC converter driver was prepared externally to be synchronized with the DC/DC converter driver for IC201 and eliminate noise. F 82 DEH-P8MP/XN/UC 1 2 3 4 WWW.PCBOOK.IR 5 6 7 8 - DC/DC Converter 2 A VCC1 IC241 UPC494GS VCC2 VOLTAGE DIVIDER ERROR AMP DC/DC CONVERTOR 2 COMPARATOR VOLTAGE DIVIDER PULSE OUTPUT VOLTAGE BOOSTER TRIANGULAR WAVE OSCILLATOR OUTPUT PULSE of IC201 PAL008A RECTIFICATION CIRCUIT B BATTERY VOLTAGE SYNCHRONIZING CIRCUIT C Difference between VCC1 and VCC2 is detected with IC241 error amplifier to adjust the pulse output so that VCC1 and VCC2 are identical. D E F DEH-P8MP/XN/UC 5 6 7 8 83 1 WWW.PCBOOK.IR 2 3 4 3 4 7.4 CLEANING A Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools: Portions to be cleaned CD pickup lenses Cleaning tools Cleaning liquid : GEM1004 Cleaning paper : GED-008 B C D E F 84 DEH-P8MP/XN/UC 1 2 5 WWW.PCBOOK.IR 6 7 8 8. OPERATIONS A B C D E F DEH-P8MP/XN/UC 5 6 7 8 85 1 WWW.PCBOOK.IR 2 3 4 3 4 A B C D E F 86 DEH-P8MP/XN/UC 1 2 5 WWW.PCBOOK.IR 6 7 8 A B C D E F DEH-P8MP/XN/UC 5 6 7 8 87 1 WWW.PCBOOK.IR 2 3 4 3 4 A B C D E F 88 DEH-P8MP/XN/UC 1 2 5 WWW.PCBOOK.IR 6 7 8 A B C D E F DEH-P8MP/XN/UC 5 6 7 8 89 1 WWW.PCBOOK.IR 2 3 4 - Jigs List Name Test Disc L.P.F. Extension Cable Extension PCB CD-ROM Cleaning liquid Cleaning paper A Jig No. TCD-782 GGD1160 GGD1378 GGV1169 GEM1004 GED-008 Remarks Checking g the g grating g Checking g the g grating g ((Two pieces)) Checking g the keyboard y unit Checking g the keyboard y unit OEL screensaver studio lka to lkd application Cleaning CD pickup lenses Cleaning CD pickup lenses S/M Location P.59 P.59 P.55 P.55 P.62 P.84 P.84 B C D E / F 90 DEH-P8MP/XN/UC 1 2 3 4
Similar documents
DEH-P8400MP XN/EW - Recambios, accesorios y repuestos
1. For pickup unit(CXX1550) handling, please refer to"Disassembly"(see page 59)
More informationDEH-P3600MP/XM/EW
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
More informationDEH-P6700MP/XM/EW
4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Bel...
More informationDEH-2800MP/XN/UC
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
More information