NCR iTRAN 3000t Tabletop Transport

Transcription

NCR iTRAN 3000t
Tabletop Transport
Operator Information
B004-0000-0606
03.10.00
November 15, 2009
The product described in this book is a licensed product of NCR Corporation. Other brand and product names
appearing in this publication are the trademarks or registered trademarks of their respective holders.
It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software, and
firmware become available. NCR, therefore, reserves the right to change specifications without prior notice.
All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In
some instances, photographs are of equipment prototypes. Therefore, before using this document, consult with your
NCR representative or NCR office for information that is applicable and current.
To maintain the quality of our publications, we need your comments on the accuracy, clarity, organization, and value
of this book.
Address correspondence to:
NCR Waterloo
Attention: Information Engineering
580 Weber Street North
P.O. Box 1611
Waterloo, Ontario, Canada
N2J 4G5
Copyright © 2006, 2007, 2008, 2009
By NCR Corporation
Dayton, Ohio U.S.A.
All Rights Reserved
Contents
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
About This Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Revision Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Chapter 1: Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Identifying System Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Original Feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
New Operator Accessible Feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Scanner with External Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Encoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Pockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Turning The System ON / OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Preparing Documents for Processing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Inserting and Removing Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Clearing Document Jams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Solving Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Power Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Document Feeding Slows Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
New Operator Accessible Feeder Replacable Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Encoding Dropouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Endorser Print Drum Print Quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Refilling Endorser Print Drum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Chapter 2: Maintenance Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Why Should The Workstation Be Cleaned? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
What and When Should You Clean ? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Start-of-Shift Cleaning Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clean The Roll-On Stamp Drums . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ink-Jet Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Encoder Ribbon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NCR iTRAN 3000t Operator Information
24
25
26
30
31
31
32
1
Contents
Chapter 3: Ordering Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Roll-On Stamp Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Chapter 4: Replacing Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
New Operator Accessible Feeder Replacable Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Encoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
40
43
44
45
Appendix A: Character Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Magnetic Scanner Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Ink-Jet Fonts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Appendix B: System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
System Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Environmental conditions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electromagnetic immunity: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power supply: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interface: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Dimensions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Processing Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acceptable Documents: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Image Capture Details: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Encoder Details (Thermal): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Endorser Details (Ink Jet): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Roll-On Stamp Placement Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CE Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
52
52
52
52
52
53
53
54
55
55
55
55
57
58
Preface
About This Book
This book contains Operator information for the NCR iTRAN 3000t Table-Top Item Processing
System.
Intended Audience
This book is for operators or supervisors who use and clean the NCR iTRAN 3000t Table-Top Item
Processing System.
Conventions
Within the procedures described in this book, conventions help you to identify different types of
information.
Bold
Bold identifies anything you must select, choose, run, press, or type. For example:
Type dbscrpt, then press Enter.
Chevrons
Chevrons (>) indicate a series of menu selections. For example:
Choose File > Import > Formats.
Italics
Italics identify a placeholder that must be replaced with your own specific information. For example:
device=c:\path\7780mint.sys type=H.
Italics are also used for emphasis.
3
Preface
Notes, Tips, Important, Cautions, Warnings
Notes, cautions, and warnings alert you to important or critical information. Each is displayed in a
different way:
Note: Notes contain information that has special importance.
*
Tip: Tips contains useful advice for the user on tasks or procedures.
!
Important: Important text contains information to which the reader should pay close attention.
Caution: Cautions alert you to procedures or conditions that could damage equipment or data.
Warning: Warnings alert you to procedures or conditions that could cause personal injury.
4
Revision Record
April 1, 2006
Section
Revision
All
First release
June 23, 2006
Section
Revision
All
Added Encoder information
October 23, 2006
Section
Revision
Chapter 3
Corrected the Encoder Ribbon order number
Appendix B
Added roll-on stamp print location details
October 30, 2007
Section
Revision
Chapter 3
Corrected the Image Camera Cover (plastic), Feeder Reject group (Document Wiper) &
Absorbing felt for endorser, order numbers on pg 27
Updated pictures on pages 10, 19 & 34. Updated info on document feeding on pg 15.
Updated pocket capacity info on pg 41 Added encoder ribbon capacity of 6300 amount
fields to pg 43. Updated endorser specifications on pg 43, 44
5
Revision Record
May 30, 2008
Section
Revision
Chapter 1
Added Refilling Instructions for refilling the Roll-On Stamp on Pg 16
Chapter 2
Added note “No warning messages will be displayed when the cartridge is empty” on page
20.
Chapter 3
Updated minimum order quantities on Pg 27 Roll on Stamp Ink Refill and Roll on Stamp
Added 3 new NCR-Direct part numbers to Pg 27 and added reference to Note 3 on Pg 28.
Appendix B
Added to page 39 “Caution not to have cell phones, blackberries etc. within 1 meter of the
MICR reader”
November 15, 2009
6
Section
Revision
Chapter 1
Added updates to Operating Procedures
Chapter 2
Added updates to Operator Maintenance Procedures.
All
Added information on Operator Accessible feeder, new camera cover and external power
supplies for Scanner Modules.
Chapter 2 & 3
Added Systemedia part numbers for new hopper rollers and extended camera covers.
Added serial number break-ln’s for new hopper and extended camera covers.
1
Operating Procedures
This chapter details the operator procedures that are required to:
turn the system ON / OFF
prepare the system for operation
load documents for processing
clear document jams
solving problems
7
Chapter 1: Operating Procedures
Identifying System Parts
Original Feeder
1 - Adjustment knobs (for parallelism between Feeder and Reader).
2 - Document bin for automatic feeding
3 - Document presser
4 - Access cover for reject group
8
New Operator Accessible Feeder
Caution: Lift the operator cover both ends at once straight up
New feeder serial number break-in is SN100832
9
Scanner
1 - ON/OFF indicator switch
2 - Front scanner
3 - Ink-jet print head
4 - Rear scanner
5 - Connection USB 2.0
6 - Mains fuse
7 - Connector power supply
10
Scanner with External Power Supply
New external power supply serial number break-in is SN100672
11
Encoder
The encoder module contains a thermal encoder and two roll-on stamps.
12
Pockets
1 - Document guide slot
2 - Document guide blade (3 per module)
3 - Single reject pocket
4- Variable document length guide
5 - Collections pockets (3 per module)
13
Turning The System ON / OFF
Turning The System ON / OFF
1
Make sure that the controller PC is turned on and ready for use.
2
Perform the start of day cleaning (see Chapter 2).
3
Turn on the system power switch (Item 1 in the scanner picture.)
In this system, the encoder is disabled.
4
5
14
Listen for the usual startup tests from the system:
a
Motors turn on
b
The scanner lights turn on for approximately 2 seconds
c
The LED on the encoder flashes during startup and download for approximately 30 seconds.
d
A beep sounds when USB connections are established with the PC controller and the
system is ready
At the PC controller, start your application program.
Preparing Documents for Processing
Preparing Documents for Processing
It is important to prepare all documents properly before processing them on the workstation.
Otherwise more document jams may result and document throughput may be reduced.
If possible, create batches of work that contain documents of similar lengths as batches of similar
lengths will likely run with fewer jams.
Running documents longer than 8.5 inches will increase the likelihood of document jams.
Removing Staples, etc.
Remove staples, paper clips, rubber bands, pins and other foreign objects from all documents.
Repairing Damaged Documents
It is especially important to fix all documents before processing them. Unfold any folded documents,
repair dog ears, repair any tears or ripped edges. If an item cannot be repaired then use a carrier
document. This will help alleviate jams.
Jogging Documents for the Feeder
Before loading a stack of documents into the feeder, you must jog them first. Otherwise, documents
may misfeed slowing down throughput.
Use a mechanical jogger set to its highest setting for about 15 seconds.
If documents of different sizes are being processed, then it is very important to jog the documents
for a longer time.
15
Inserting and Removing Documents
Inserting and Removing Documents
This section tells how to insert and remove documents from the following parts of the workstation:
The feeder
The pockets
For instructions on removing jammed documents from various parts of the workstation, see “Clearing
Document Jams” later in this chapter.
Feeder
To ensure the feeder feeds documents, read the following instructions carefully.
To load a stack of documents into the main feeder, follow these steps.
1
Remove staples and paper clips
2
Check for dog ears on the bottom lead edge by fanning the documents. Remove the dog ears
by straightening them as they may cause track interrupts.
3
Fan the documents, from both sides, to be sure they do not stick to one another.
4
Jog the documents before placing them in the feeder. Turn the jogger on its highest setting for
about 15 seconds, run your fingers over the documents to create gaps and help the documents
settle to the bottom.
5
Take hold of the documents to be loaded in the feeder in one hand such that your thumb is on
the first document. Push the document presser (item 3 in the feeder picture back with the same
hand. Use your other hand to support any documents already in the tray. Keep a steady pressure
on the documents already in the tray. (be careful not to pull up on the documents already in the
tray)
NOTE: Do not fill the feeder over 2/3 full for optimal feeder operation.
6
Make sure all documents are right side up and facing toward you.
7
Place the documents into the tray in a vertical manner ensuring they do not lean forward or
misfeeds may result. The lead edge of the documents should be against the right wall of the tray.
8
Allow the document presser to move forward gently against the bundle of documents.
Pockets
To remove documents from or put documents back into a pocket, simply hold the paddle open with
one hand and handle the documents with the other.
16
Clearing Document Jams
Clearing Document Jams
Document jams are a part of item processing. You can diminish jams by careful document
preparation, and by making sure the documents are dry and clean.
If a document jam occurs:
1
Click on the continue button (displayed on the monitor). This will attempt to flush the documents
to the reject pocket. If this fails then:
Starting with the downstream document, carefully work each document up and out of the
transport.
Where possible turn the rollers by hand to help clear the jam.
Stack the documents in sequence as you remove them.
2
3
If a metal object caused the jam, make sure that:
a
The scanner camera-covers are not damaged.
b
The endorser stamps do not have embedded metal or damage.
c
There are no metal fragments on the scanner heads.
Follow the application prompts to reprocess the items that were removed, in the order the
application requests them.
17
Solving Problems
Solving Problems
Power Problems
Momentary power outages can result in the encoder not running, while the other system modules
remain running. In this instance, documents jam at the encoder entrance.
Turn the scanner power off, wait ten seconds, then turn the scanner power on again; the system
should now operate normally.
Document Feeding Slows Down
Document throughput drops to 90 DPM from the normal 200.
Clean the track sensor in the feeder.
Ensure the new Double Feed sensor kit has been installed. NCR part number 877-0233180
(See picture below of new sensor) If the sensor does not look like this, get your CE to order one and
install it for you.
18
Solving Problems
New Operator Accessible Feeder Replacable Parts
If feeding problems persist and the feeder is operator accessible:
remove the top cover as shown earlier in this book
the picker roller and retard roller are replacable by lifting them straight up.
Note: New feeder serial number break-in is S/N100832.
19
Solving Problems
Encoding Dropouts
If the encoding shows dropouts (voids) check the expiry date on the encoding ribbons. Expired or
improperly stored ribbons can cause this problem.
Order no more than a six-month supply of fresh encoding ribbons, and store them in a cool place
away from cleaning solvents.
20
Solving Problems
Endorser Print Drum Print Quality
When a print drum begins to print too light (approximately 200,000 documents after a refill), the print
drum must be refilled. If after cleaning and refilling a print drum it still makes poor endorsements, at
approximately 1,000,000 impressions, it must be replaced.
Refilling Endorser Print Drum
Refill by pouring ink in holes A,B, and C, as per the following procedure:
1
Pour the ink into each hole until it is full
2
Wait until the ink is absorbed (about 10 - 15 min.) and then refill again
3
Repeat this sequence (3 - 4 times) until the roll-on stamp will not absorb more ink
21
Solving Problems
22
2
Maintenance Procedures
This chapter details the operator maintenance procedures that are required to keep the NCR iTRAN
3000t operating at optimum performance.
Start of shift cleaning is required.
Supplies like the ink-jet cartridge must be replaced when they are used up.
23
Chapter 2: Maintenance Procedures
Why Should The Workstation Be Cleaned?
Why Should The Workstation Be Cleaned?
In any document processing operation there is paper dust (from the documents). This dust, together
with small bits of paper, collects in the workstation. The workstation should be cleaned to avoid the
following issues
more documents may jam slowing throughput
feeder module may miss-feed or double-feed
more misreads and rejects may be generated
the codeline and document images displayed on the monitor are fuzzy and hard to read
the workstation may need service more often resulting in lost time
A Note about Paper Dust
During document processing small pieces of paper come off the documents. Paper Dust clogs the
sensors that tell the iTRAN 3000t where each document is. It also gathers on the scanner module,
making it difficult for the workstation to read the documents correctly
It normally takes less than 10 minutes at the start of shift to clean the paper dust from the track.
By cleaning the iTRAN 3000t, fewer track interruptions will be generated.
Each iTRAN 3000t should have cleaning materials (including a vacuum cleaner) close by.
Location of Track Sensors
24
What and When Should You Clean ?
What and When Should You Clean ?
You must clean certain parts of the workstation at least once every day. If the site is running more
than one shift, clean at the start of each shift. The section starting on the next page gives a complete
procedure for cleaning all of these parts.
Other parts of the workstation need cleaning less often. For instructions on cleaning each of these
parts, go to the section of this chapter that covers the module in question.
Note: These guidelines are for workstations with normal dust buildup. If the workstation is reporting errors
caused by dust, the workstation should be cleaned more frequently. It takes time to stop operations and
clean the workstation, but time will be saved by having fewer problems processing documents.
Caution: Don’t try to lift or remove any covers unless instructed to do so. Some covers are only meant for
service personnel.
25
Start-of-Shift Cleaning Procedure
Every day before starting the workstation, perform these cleaning tasks:
1
Clean the entire length of the track using a vacuum cleaner.
2
Clean the track sensors
3
Clean the camera covers
4
Clean the roll on stamp drums (if equipped)
How to Clean the Workstation
To clean the workstation follow the instructions below. While cleaning, check parts such as ribbons,
and rollers for wear or damage. If a part needs replacing and this book tells how to replace it, follow
the instructions carefully. Otherwise call for service.
Caution: When blowing air or vacuuming, avoid touching the encoder ribbon and the endorser cartridge.
Most cleaners won’t remove the ink from the endorser cartridge. It will wash off your skin gradually, but may
be permanent on clothing. The encoder ink is more easily removed.
1
Turn off the workstation.
2
Remove any documents that are in the feeder.
3
Remove the ink jet cartridge.
See the instructions for removing the ink-jet cartridge on Pg 30
4
Set the vacuum to blow air. Then use the crevice attachment to blow bits of dust from the
workstation.
If the vacuum is not equipped to blow air, a can of non-condensing compressed air can be used.
Keep the can upright and bend the plastic nozzle so the air can get into the track.
Caution: Only use compressed air which is intended for use on camera lenses. (Check the label).
26
5
Start cleaning, starting at the feeder, moving down along the inside of the track. Blow out any
dust you can see, but do not force the tool against any parts of the workstation. Do this for all
modules.
6
Repeat Step 5 with the vacuum set to suction.
Cleaning the Track Sensors
Using the cleaning swabs (Systemedia cleaning swab #523396) Slide the swab down the side of
the track walls at the sensor locations (both sides) and gently move up and down to remove dust
from the sensors. See pictures on Page 24 showing the track sensor locations.
Cleaning the Image Camera Covers
1
Slide each image camera cover up and off the camera body, then clean it with soap and water,
then dry with a dry cloth. (see chapter 3 for ordering information). DO NOT USE ALCOHOL.
Ensure there is no build up of ink deposits on the cover.
Replace any cracked covers. (see Chapter 3 “Ordering Supplies”)
.
Caution: If you find spilled ink. Wipe the ink up with a cloth and dispose of the cloth.
.
27
2
28
Re-install the camera cover by sliding the cover down over the camera body, until the upper tab
rests on the camera body.
Feeder Cleaning the Feed Roller
Cleaning the feed roller should be done if the feed roller looks dirty or there is an unusual number
of double feeds or misfeeds.
The roller can be cleaned using a swab soaked with isopropyl alcohol.
If the document wiper appears to be glazed, the wiper can be turned by 1/3 of a turn to expose
another surface. This can be done twice (all three surfaces used). Once all three surfaces are used
the wiper should be replaced (see ordering parts in chapter 3 & replacing parts in chapter 4).
29
Clean The Roll-On Stamp Drums
Check the Roll-On stamp drums for a build-up of ink and dust. This is not a frequent problem; you
only need to clean the roll-on stamps if the build-up lowers the print quality.
You need the following supplies:
A soft nylon brush (like a tooth brush)
Disposable gloves to keep your hands clean
.
Be careful
the
thumbscrews
not to drop
Caution: Be careful not to drop the retaining nuts into the machine. If you do, call NCR for service
help.
.
1
Undo the retaining nuts that hold the print drums in place, then set them aside
2
Put on the disposable gloves, then lift a print drum up and off its shaft.
3
Hold the print drum inside the garbage can, then gently use a soft brush to remove all ink and
dust deposits.
4
Inspect the clean print drum for damage.
If the print drum is usable, reinstall it in the encoder module.
If the print drum is damaged, dispose of it, and install a new one.
30
5
Repeat steps 2 through 4 for the second print drum.
6
Replace the retaining nuts, and tighten them gently so that you can remove them as needed. n
Replacing Supplies
Replacing Supplies
Ink-Jet Cartridge
Note:
No warning messages will be displayed when the cartridge is empty.
While running the machine, occasionally check the ink-jet endorsement for quality and when the
cartridge needs replacement, proceed as follows:
1
Lift off the ink-jet cover.
2
Pull the latch (D) away from the ink-jet cartridge (C), then lift out the old cartridge.
3
Unwrap the new cartridge, and pull off the shipping tape.
4
Pull the latch out and insert the new cartridge, front first, then push down the rear of the cartridge
then release the latch.
If the cartridge is properly in place, the latch will fit snugly against the cartridge.
Note:
5
When properly installed the front of the cartridge will be slightly lower than the rear.
Test the print quality. n
31
Replacing Supplies
Encoder Ribbon
When the encoder ribbon needs to be replaced, your workstation stops moving documents and
displays a message on the workstation screen.
Get a replacement encoder ribbon, then follow these steps to replace the used ribbon:
32
1
Swing open the front encoder door.
2
Pull the end of the ribbon off the empty ribbon spool .
3
Lift out the empty ribbon spool.
4
Pull the empty core off of the supply spool Do not discard the paper core. Set both parts aside
for later use.
Replacing Supplies
5
Roll the last of the ribbon onto the take-up spool (turn the take-up spool by hand), then pull the
take-up spool out of the holder.
6
Pull the used ribbon roll off the take-up spool. Discard the used ribbon roll, but SET THE SPOOL
ASIDE.
7
Unwrap the new ribbon, then push the ribbon, notched end first, onto the supply spool. Make
sure the notches lines up.
Align the notch and tab, then push the cardboard core until the ribbon is fully in place against
the wall of the feed spool.
8
Remove the tape from the new ribbon leader. SAVE THIS PIECE OF TAPE.
33
Replacing Supplies
9
Snap the supply roll into the holder.
10 Gently push the green print-head latch to the right, then lift it up slightly to unlatch the print head.
11 Press down on the forward portion of the print head (closest to the track) so that it points down
at an angle.
12 Pull up on the end of the new ribbon until you have unrolled all of the ribbon leader.
13 Place the end of the ribbon leader over the top of the print head.
14 Push the leader forward over the print head with your fingers. As you push the ribbon leader
forward, wiggle it slightly from side to side to keep it from getting caught. Be sure that the ribbon
goes under the green lower guide bar.
34
Replacing Supplies
Stop when you see the end of the ribbon leader appear under the ribbon holder.
15 Pick up the take-up spool and the empty cardboard ribbon core (saved previously).
Push the notched end of the cardboard core over the take-up spool. Align the notch and
tab, then push the core into place.
16 Hold the take-up spool over the encoder with the notch to the right.
Bring the ribbon leader under the take-up spool and wrap it around the take-up spool.
35
Replacing Supplies
17 Align the ribbon edge with the core edge and tape the end of the ribbon leader to the core on
the take-up spool with the piece of tape you saved.
Make sure that the leader edge is not taped crookedly onto the core.
18 Turn the take-up spool until all the ribbon leader is wrapped on the core.
19 Snap the take-up spool into place on the ribbon housing.
20 Push straight down on the green latch. As it moves downward, the carriage will move down also.
When the latch stops moving, press down hard until the latch clicks into the operating
position.
21 Turn the take-up spool until the ribbon is tight.
22 Close the encoder door. n
36
3
Ordering Supplies
The following supplies for your NCR iTRAN 3000t system can be ordered from NCR.
http://www.ncr-direct.com/
Table 3-1:
Description
Order Number
Qty / Package
Cleaning tissue, dry (for ILM)
523406
50
Cleaning tissue, wet (for ILM)
523419
50
Cleaning swab
523396
100
Ink-jet cartridge, black (for Reg CC) HP C6602A
203250
1
Ink-jet cartridge, red
203247
1
Encoder ribbon, thermal (see Note 1)
182436
6
Roll-on stamp in encoder module (see Note 2)
9418-0139
5 (Min. Order)
Ink for the roll-on stamp, bottle
9418-0140
5 (Min. Order)
Feeder reject group (document wiper) (see Note 3)
9418-0157
1
Image camera cover, plastic (see Note 3) (picture pg 28)
9418-0158
1
Image camera cover, plastic (new style) (picture pg 28)
9418-0170
1
Absorbing felt (for endorser) (see Note 3)
9418-0159
50
Tall roller (operator replacable) (new hopper)
9418-0168
1
Short roller (operator replacable) (new hooper)
9418-0169
1
UltraJet Canned Air 10oz
526487
1
Note: 1.) Each ribbon can encode approximately 6300 amount fields.
2.) You must call NCR Direct (1-800-543-8130 in the US) to order this part. The analyst will
help you specify the text and graphics to be engraved on the roll-on stamp. (There is a onetime setup fee for each unique stamp.) (Min. Order 5) See following section for stamp details.
37
Chapter 3: Ordering Supplies
Roll-On Stamp Details
Note: 3.) Order the following supplies from NCR Service, until they are available from NCR Direct.
.
Table 3-2:
Description
Order Number
Qty / Package
Feeder reject group (document wiper)
877-0231368
1
Image camera cover, plastic
877-0231334
1
Absorbing felt (for endorser)
998-0717857
50
Roll-On Stamp Details
The roll-on stamp, with reinking and careful cleaning, should last for approximately 1,000, 000
impressions. (Reinking should provide approximately 200,000 impressions.)
To order new or replacement stamps, you need call NCR Direct and be able to provide the following
information.
Shipping Address
Text and graphics for the stamp.
See www.ncr-direct.com to obtain a telephone number for your area.
Note: Use the following details for the stamp text and graphics
38
4
Replacing Parts
There are operator replaceable parts in the following modules of the iTRAN 3000t system:
Feeder
Scanner
Encoder
See the following sections for instructions.
39
Chapter 4: Replacing Parts
Feeder
Feeder
If the feed feeder has excessive double feeds, check the reject group (document wiper). If the surface
that faces the documents is worn, you can put an unused surface to work. (if all three surfaces of
the reject group (document wiper) are worn replace it with a new part)
40
1
Remove any documents from the feeder.
2
Lift off the access cover.
Feeder
3
Turn the thumbscrew to remove it.
4
Push the reject group (document wiper) away from the track.
41
Feeder
42
5
Lift the reject group (document wiper) out of the feeder, then turn it so that an unused surface
faces the document path. (if all three surfaces of the reject group have been used install a new
reject group in its place) For reject group (document wiper) part number see Chapter 3, “Ordering
Supplies”
6
Pull the shaft out, then slide the reject group (document wiper) back into place. It must slide
forward into the track opening.
7
Replace the thumbscrew.
8
Replace the cover. n
Feeder
New Operator Accessible Feeder Replacable Parts
If feeding problems persist and the feeder is operator accessible:
remove the top cover as shown earlier in this book
the picker roller and retard roller are replacable by lifting them straight up.
Note: New feeder serial number break-in is S/N100832.
43
Scanner
Scanner
If you see horizontal lines in your images, the plastic camera cover may be scratched from staples
or document jams.
The image camera covers are easily replaced:
44
1
Swing open the scanner cover.
2
Remove any jammed documents from the image area.
3
Pull the image camera cover straight up and off the camera.
4
Unwrap a new cover, then clean it with a lint free dry cloth. (See Ordering Information in chapter
3)
5
Align the new cover with the camera, then slide it into place until the upper tab rests on the
camera. n
Encoder
Encoder
The encoder module holds two rotary stamps. You can replace these stamps when they wear out,
or if your processing work needs a different endorsement.
Caution: Use disposable gloves and store unused stamps in a self-sealing plastic bag. The ink is
difficult to remove from skin and clothing.
To remove and replace a stamp:
Be careful
the
thumbscrews
not to drop
1
Open the appropriate encoder cover.
2
Using a disposable glove, unscrew the retaining nut from the top of the stamp.
Caution: Be careful not to drop the retaining nuts into the machine. If you do, call NCR for service
help.
3
Lift out the stamp. Either dispose of it, or store it in a sealed plastic bag.
4
Unwrap the new stamp, then slide it over the shaft.
5
Align the notch in the stamp with the roller, then push the stamp down into place.
6
Reinstall the retaining nut, and tighten it gently so that you can remove it as needed. n
For further endorser information see “Refilling Endorser Print Drum” on page 21. Also see “Clean
The Roll-On Stamp Drums” on page 30
45
Encoder
46
A
Character Sets
Magnetic Scanner Characters
CODE
DECIMAL
HEXADECIMAL
Magnetic Scanner CHARACTERS
ASCII
E13B
32
20
SPACE
35
23
#
43
2B
+
45
2D
-
48
30
0
0
49
31
1
1
50
32
2
2
51
33
3
3
52
34
4
4
53
35
5
5
54
36
6
6
55
37
7
7
56
38
8
8
57
39
9
9
58
3A
:
A
59
3B
;
B
60
3C
<
C
61
3D
=
D
62
3E
>
74
4A
J
78
4E
N
80
50
P
88
58
X
CMC7
47
Appendix A: Character Sets
48
93
5D
]
124
7C
|
33
21
!
UNKNOWN CHARACTER READ
63
3F
?
UNKNOWN CHARACTER READ
Ink-Jet Fonts
The following chart shows the print-characters for the ink-jet endorser.
Note: The roll-on endorser (stamps) are a customer-ordered supply item.
0
1
2
3
4
5
6
7
0
SP
0
@
P
‘
p
1
!
1
A
Q
a
q
2
“
2
B
R
b
r
3
#
3
C
S
c
s
4
$
4
D
T
d
t
5
%
5
E
U
e
u
6
&
6
F
V
f
v
7
‘
7
G
W
g
w
8
(
8
H
X
h
x
9
)
9
I
Y
i
y
A
*
:
J
Z
j
z
B
+
;
K
[
k
<
L
\
l
M
]
N
^
C
,
D
-
E
.
=
>
m
{
}
n
_
F
/
?
O
o
49
50
B
System Information
This chapter contains environmental information and system certifications.
Caution: Moving or disassembly of the system should be preformed by qualified service personnel.
Caution: If you move the system, make sure that you connect all power cords to the same power
circuit, and that this circuit is not shared by laser printers, photocopiers, or heavy inductive
load. All system components, including the PC and monitor, must be connected to a single
power bar.
Caution: Modern MICR readers have improved sensitivity and accuracy; as a result they can be
affected by other high power electronics.
Please do not allow Cell Phones, Blackberries, Blue Tooth enabled devices and Power
Packs within 1 meter of the MICR reader.
51
Appendix B: System Information
System Characteristics
Environmental conditions:
Table B-1:
Temperature:
from 10°C to 40°C
Humidity (no condensation):
from 20% to 80%
Temperature gradient:
15°C/hour
Electromagnetic immunity:
The product will function correctly if positioned at a minimum distance of 10 cm from an
electromagnetic emission source (video, PC, etc.)
Power supply:
The power supply is switching and can therefore be used if a specific mains cable is included, in all
the different countries for which it is destined. An ON/OFF switch is located on the reader.
All system components, including the PC and monitor, must be connected to a single power bar.
We strongly suggest that you use a surge-protected power bar.
Mains and power:
100-240 V AC 120 W 50÷60 Hz
Interface:
USB 2.0
52
Product Dimensions:
Table B-2:
Size
Feeder
Reader
Encoder
3-Pocket
Bin
Length:
237 mm
436 mm
356 mm
250 mm
160 mm/250 mm
max
Width:
161 mm
265 mm
254 mm
215 mm
60 mm
Height:
152 mm
200 mm
166 mm
115 mm
60 mm
Feeder
Reader
Encoder
3-Pocket
Bin
3 Kg
10,5 Kg
7,7 Kg
4,5 Kg
4,5 Kg
Table B-3:
Weight:
Capacities
Feeder
The feeder holds up to 500 documents (minimum thickness)
Pocket
Each pocket bin holds approximately 250 documents (depending on paper weight and quality of
documents, the quantity can be much less in some cases).
53
Processing Rates
A USB 2.0 interface is required in the controlling computer, but the thoughput of this interface varies
with the chip-set used by the computer manufacturer. The type of image capture used also impacts
processing rates:
Thru-puts specified below are measured with a 6” document and a Pentium 4 spec PC.
Table 1:
Mode Of Operation
54
Thruput
9850-8201
Thruput
200X200 dpi scan, front + rear images (16 level grey)
200 dpm
200 dpm
200X200 dpi scan, front + rear images, (256 level grey)
200 dpm
200 dpm
100X100 dpi scan, front + rear images, (24 bit color)
190 dpm
100 dpm
200X200 dpi scan, front + rear images, (24 bit color)
160 dpm
75 dpm
Red Drop-out mode 200 dpi
200 dpm
n/a
Amount field encoding (6” docs)
65 dpm
65 dpm
Endorsing (one line: 71 characters)
200 dpm
200 dpm
Pocketing (1-10 pockets)
200 dpm
200 dpm
9850-8204
Acceptable Documents:
Table B-4:
Height:
from 60 mm to 108 mm
Length:
from 130 mm to 216 mm
Thickness:
from 0.07 mm to 0.12 mm
Weight:
from 70 g/mq to 120 g/mq
Image Capture Details:
Table B-5:
Resolution:
(100 dpi x 100 dpi) (3.93 X 3.93 ppmm)
(200 dpi x 200 dpi) (7.87 X 7.87 ppmm)
Grey scale:
256 or 16 grey levels
Illumination:
RGB illumination (illumination Red-Green-Blue)
Red = 630 nm
Green = 520 nm
Blue = 465 nm
Encoder Details (Thermal):
Table B-6:
Encoding Amount Field Only:
Approximately 6300 Documents / per ribbon
Endorser Details (Ink Jet):
Table B-7:
Number of lines printed:
1 on rear of document
Character spacing: Prior to WiseIP Ver 5.05
15 characters per inch
Character spacing: WiseIP Ver 5.05 & later
10 or 15 characters per inch
Print position:
centered 33 mm from document bottom
fixed at 15 mm from leading edge
Character height
2.3mm
Character capacity:
600,000 draft characters per cartridge
300,000 bold characters per cartridge
55
NOTES:
WiseIP allows a maximum of 85 characters to be endorsed.
There is no checking done to see if the document is long enough to endorse the number of
characters entered. For example, if one selects 85 characters to be printed on a 6” (152mm)
document, only the first 80 characters will be printed - the last 5 characters will not be printed
since the document is not long enough - no error message is generated to indicate the last 5
characters have not been printed.
WiseIP does not allow bold endorse print.
WiseIP does not support downloadable fonts on the iTRAN 3000t
56
Roll-On Stamp Placement Details
Roll-On Stamp Placement Details
57
CE Declaration of Conformity
CE Declaration of Conformity
58
B004-0000-0606
November 15, 2009

NCR iTRAN 3000t Tabletop Transport

Transcription

Similar documents

The new NCR Orderman7.

NCR iTRAN 8000 Datasheet

TERX0195_Impulse Control Sys-2 w.indd

Remote Video Monitoring Solutions

MP 9 MP9-N MP45 MP 9 MP9-N MP45 MP9 MP9

banque saudi fransi (bsf), saudi arabia

2016 Paul Bunyan ShowSM Loader Competition Saturday, October

GO WITH THE FLOW

CONTROL SYSTEM HiCOS - HIGHVOLT Prüftechnik Dresden GmbH

a new dimension: DYCS Brieda Cabins