SRF-MQ11

SRF-MQ11
SERVICE MANUAL
US Model
AEP Model
UK Model
E Model
Australian Model
Ver. 1.2 2005.03
SPECIFICATIONS
Radio segment
Model for North and South America
Frequency range: FM 87.5-108 MHz
Channel step: 0.1 MHz
Model for other countries/regions
Frequency range: FM 87.5-108 MHz
Channel step: 0.05 MHz
Power output: 3.0 mW + 3.0 mW (at 10% harmonic distortion)
Headphone segment
Headphone type: Open-air Dynamic
Driver unit: ø 30 mm Dome type
Input: ø 3.5 mm stereo mini-jack
Power handling capacity: 1 000 mW (IEC)
Impedance: 24 Ω (at 1 kHz)
Frequency response: 20 to 24 000 Hz
Others
Power requirements
1.2 V DC, Built-in nickel metal hydride battery
4.5 V DC, Charge in the AC power adaptor
Mass
Approx. 75 g (2.65 oz)
Accessories supplied
Connecting cord (1), AC power adaptor (1)
Design and specifications are subject to change without notice.
FM STEREO PLL
SYNTHESIZED HEADPHONE RADIO
9-877-505-03
Sony Corporation
2005C16-1
© 2005.03
Personal Audio Group
Published by Sony Engineering Corporation
SRF-MQ11
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
• Use the Sony AC power adaptor (supplied) only. The polarity of the plugs of
other manufacturers may be different. Failure to use the recommended AC
power adaptor may cause the unit to malfunction.
Polarity of the plug
Unleaded solder
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
For the customers in the U.S.A.
RECYCLING NICKEL METAL HYDRIDE BATTERIES
Nickel Metal Hydride batteries are
recyclable.
You can help preserve our environment by returning
your used rechargeable batteries to the collection
and recycling location nearest you.
For more information regarding recycling of
rechargeable batteries, call toll free
1-800-822-8837, or visit http://www.rbrc.org/
Caution: Do not handle damaged or leaking
Nickel Metal Hydride batteries.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
2
TABLE OF CONTENTS
1. GENERAL ·········································································· 3
2. DISASSEMBLY
2-1. Cabinet (Rear) Assy (R) ·················································· 4
2-2. MAIN Board ··································································· 5
2-3. MICROCOMPUTER Board ··········································· 5
2-4. Hanger (R) Section ························································· 6
2-5. Speaker (R) ····································································· 7
2-6. Cabinet (Rear) Assy (L) ·················································· 7
2-7. Hanger (L) Section ·························································· 8
2-8. BATTERY Board ···························································· 9
2-9. Speaker (L) ····································································· 9
3. ADJUSTMENTS ···························································· 10
4. DIAGRAMS
4-1. Block Diagram ······························································ 12
4-2. Printed Wiring Board – MAIN Board – ······················· 13
4-3. Schematic Diagram – MAIN Board – ························· 14
4-4. Printed Wiring Board
– MICROCOMPUTER Board – ·································· 15
4-5. Schematic Diagram
– MICROCOMPUTER Board – ·································· 16
4-6. Printed Wiring Board – BATTERY Board – ················ 17
4-7. Schematic Diagram – BATTERY Board – ·················· 18
4-8. IC Pin Function Description ········································· 20
5. EXPLODED VIEWS ······················································ 21
6. ELECTRICAL PARTS LIST ······································· 22
SRF-MQ11
SECTION 1
GENERAL
This section is extracted
from instruction manual.
OFF•ON/
MEGABASS
Cord
Cordon
DC IN 4.5 V
AUDIO IN
VOL*
SENS DX/LOCAL
R (right)
R (droite)
L (left)
L (gauche)
Display
Afficheur
Driver unit
Oreillettes
Jog Lever (MODE/ENTER)
Molette (MODE/ENTER)
* There is a tactile dot beside volume to show the
direction to turn up the volume.
Un point tactile, situé à côté de la molette de
volume, indique le sens dans lequel il faut tourner
pour augmenter le volume.
When Disposing of the Radio
This radio has a built-in Nickel Metal Hydride battery. When you recycle the
battery, remove it following the procedure below.
Certain countries/regions may regulate disposal of the battery
used to power this product.
Please consult with your local authority.
Note
Never disassemble this radio excepts when disposing of it.
To remove the Nickel Metal Hydride battery
The Nickel Metal Hydride battery is stored in the left unit.
1
2
Remove both screws on the left cabinet (as
shown in the illustration) using a Phillips
screw driver.
Remove the cabinet.
Cabinet
L (left)
Connector
3
Dettach the connector shown by the arrow in
the illustration and then remove the screw on
the circuit board.
4
Raise the circuit board and remove the Nickel
Metal Hydride battery using a thin object, as
the battery is secured with tape.
Nickel Metal Hydride battery
3
SRF-MQ11
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
SET
2-1.CABINET (REAR) ASSY (R)
(Page 4)
2-6.CABINET (REAR) ASSY (L)
(Page 7)
2-4.HANGER (R) SECTION
(Page 6)
2-2.MAIN BOARD
(Page 5)
2-8.BATTERY BOARD
(Page 9)
2-7.HANGER (L) SECTION
(Page 8)
2-5.SPEAKER (R)
(Page 7)
2-9.SPEAKER (L)
(Page 9)
2-3.MICROCOMPUTER BOARD
(Page 4)
Note :
Follow the disassembly procedure in the numerical order given.
2-1. CABINET (REAR) ASSY (R)
1 two screws
(1.4 × 6)
4 cabinet (rear) assy (R)
gray
3 Remove soldering from the two points.
2 three claws
4
red
SRF-MQ11
2-2. MAIN BOARD
3 lead wire (11core)
orange (P-SW)
2 Remove soldering from the eleven points.
brack (L-CH)
purple (CHG)
natural (ANT)
green (DCIN)
red (BATT)
4 MAIN board
white (GND)
blue (MB)
gray (R-CH)
yellow (COM)
brown (SP+)
1 connector
2-3. MICROCOMPUTER BOARD
1 screw
(B1.4 × 4)
2 MICROCOMPUTER board
5
SRF-MQ11
2-4. HANGER (R) SECTION
3 three claws
1 two screws
(B1.4 × 4)
4 cap (R)
2 hanger (R) section
5 step screw
(2 × 4)
8 hanger (R)
6 torsion spring (R)
7 base (hanger )
PRECAUTION DURING BASE (HANGER) INSTALLATION
1 torsion spring (R)
base (hanger)
4 step screw
(2 × 4)
hanger (R)
2 Align with the slot of
hanger (R).
hole
base (hanger )
torsion spring (R)
6
3 base (hanger) is rotated in the direction
of arrow 90 degrees.
SRF-MQ11
2-5. SPEAKER (R)
1 screw
(B1.4 × 4)
8 speaker (R)
6 three claws
gray
red
5 three claws
2 two claws
7 holdr (driver)
red marking
Install the speaker (R) so that
the both positions are aligned.
4 Remove soldering
from the two points.
gray
red
Convexity
3 ear pad
speaker (R)
holdr (driver)
2-6. CABINET (REAR) ASSY (L)
1 two screws
(1.4 × 6)
4 cabinet (rear) assy (L)
2 two claws
3 claw
7
SRF-MQ11
2-7. HANGER (L) SECTION
4 cap (L)
3 three claws
1 two screws
(B1.4 × 4)
2 hanger (L) section
5 step screw
(2 × 4)
8 hanger (L)
6 torsion spring (L)
7 base (hanger )
PRECAUTION DURING BASE (HANGER) INSTALLATION
1 torsion spring (L)
base (hanger)
hanger (L)
4 step screw
(2 × 4)
2 Align with the slot of
hanger (L).
hole
base (hanger )
torsion spring (L)
8
3 base (hanger) is rotated in the direction
of arrow 90 degrees.
SRF-MQ11
2-8. BATTERY BOARD
1 screw
(B1.4 × 4)
5 lead wire (11core)
natural (ANT)
yellow (COM)
blue (MB)
6 BATTERY board
3 Remove soldering
from the two points.
brack (L-CH)
orange (P-SW)
green (DCIN)
brown (SP+)
purple (CHG)
white (GND)
gray (R-CH)
red (BATT)
2 connector (CN501)
4 Remove soldering from the eleven points.
2-9. SPEAKER (L)
1 screw
(B1.4 × 4)
8 speaker (L)
6 three claws
gray
red
5 three claws
2 two claws
7 holdr (driver)
red marking
Install the speaker (R) so that
the both positions are aligned.
4 Remove soldering
from the two points.
gray
red
Convexity
3 ear pad
speaker (R)
holdr (driver)
9
SRF-MQ11
SECTION 3
ADJUSTMENTS
Setting:
SENS switch: DX
Connection:
FM FREQUENCY COVERAGE CHECK
Check a reading on digital voltmeter.
digital
voltmeter
Confirm
87.5 MHz
2.7V ± 0.5V
Confirm
108.0 MHz
8.2V ± 1.0V
FM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
TP (VT)
CT1
108.0 MHz
L1
87.5 MHz
level meter
16 Ω
+
–
set
headphone jack (i)
FM RF signal
generator
0.01 µF
TP (ANT)
22.5 kHz frequency deviation
by 400 Hz signal.
Output level: as low as possible
Adjustment Location
MAIN BOARD (SIDE A)
MAIN BOARD (SIDE B)
IC1
TP(ANT)
TP(VT)
CT1
FM TRACKING
ADJUSTMENT
10
L1
FM TRACKING
ADJUSTMENT
IC101
SRF-MQ11
SECTION 4
DIAGRAMS
Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
• C : panel designation.
• A : B+ Line.
• H : adjustment for repair.
• Power voltage is dc 1.5 V and fed with regulated dc power
supply from battery terminal or DC in jack (J501).
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
(
) : power supply from DC in jack
*
: impossible to measure
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : FM
Note on Printed Wiring Board:
• Y : parts extracted from the conductor side.
• b : Pattern from the side which enables seeing.
•
: Carbon pattern.
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
Parts on the pattern face side seen from
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
• Waveforms
1 IC301 tg XOUT
1.3 Vp-p
13.3 µs ns
1V/DIV , 10 µs/DIV
11
11
SRF-MQ11
4-1. BLOCK DIAGRAM
16
IC1
29
2 IN B
15
Q3
2
12
19
S501
16
MEGA BASS
ON
1 IN A
13
SPEAKER
R-CH
OFF
IC101
OUT C 18
3 VREF
RV101
VOL
AGC IN 1
SPEAKER
L-CH
4
8
11
CF2
Q2
C1
5 PW MUTE
CF1
D1
21
CT1
J502
AUDIO IN
6
C2
L1, CT1
Q101
T201
VCC
D201
S302
Q102
Q201, Q202
Q103
VDD
RECHARGABLE
BATTERY
NI-MH
1PC, 1.2V
S502
MEGA BASS
ON
OFF
31
50
(MUTE)P4-3
(POWER ON1) P2-0
(VDET 1)INT 1
51
P2-1 (VDET 2)
OUT
VDD
Q304
SWITCH
42 (POWER ON2) P3-0
J501
DC IN 4.5V
IC301
28
(POWER SW) INT2 34
(CHARGE) P4-2 30
IC501
REG
Q305, Q306
SWITCH
(DC IN) P1-3 26
5 VOUT
VIN 1
IN
(ENTER/MODE) P9-2 21
(-) P9-1 20
IC303
RESET
(+) P9-0 19
GND
IC302
LEVEL DET
GND
D504
Q501 - Q504
SWITCH
IC304
LEVEL DET
GND
IN
VDD
IN
L1
D2
S301
MODE/ENTER
LIQUID CRYSTAL DISPLAY
12
12
• SIGNAL PATH
: FM
SRF-MQ11
4-2. PRINTED WIRING BOARD – MAIN BOARD –
MAIN BOARD
•
: Uses unleaded solder.
MAIN BOARD
(SIDE A)
(SIDE B)
C
E
B
C
E
E
B
15
1
C
B
24
13
E
IC1
B
B
16
SPEAKER
R-CH
IC101
E
C
C
30
1
12
TP(ANT)
RV101
VOL
11
TP(VT)
1-860-776- (11)
11
B
MICROCOMPUTER
BOARD
CN301
(Page 15)
1-860-776- (11)
5
7
3
8
4
10
9
11
6
1
2
A
BATTERY BOARD
(Page 17)
• Semiconductor
Location
Ref. No.
13
13
Location
D1
D2
D3
D101
F-6
D-11
F-6
F-11
IC1
IC101
D-6
D-13
Q2
Q3
Q101
Q102
Q103
D-8
D-9
C-13
C-14
C-15
SRF-MQ11
L1
RF COIL
CT1
C34
0.01
R2
100k
R5
100k
L3
27nH
C9
4p
C103
10
6.3V
C101
4.7
10V
C8
220p
C13 0.01
R9
0
R18
*1
C14
0.1
R23
*2
R104
4.7
C117
1
R101
220k
C2
1000p
C4
1p
C111
0.1
C118
100
4V
C29
0.22
C116
1
C109
0.1
R102
4.7
Q101
2SB1689-T106
C108
0.1
D1
HVC202B TRU
C6
1000p
C102
2.2 10V
D3
HVC202B TRU
R4
220k
C1
1000p
D2
HVC202B TRU
R1
100k
R103 C110
4.7
0.1
4-3. SCHEMATIC DIAGRAM – MAIN BOARD –
IC1
TA2154AFN-EL
IC101
TA2179FNG
(EL)
R21
10
R15
1k
R19
*1
C16
0.01
R20 C15
0 1000p
C30
0.22
C22
1
R24
*2
C120
2200p
CF2
10.7MHz
Q3
2SC3931-C-TX
C19
0.1
C25
0.47
C20
220
4V
R13
470k
C23 R17
1
1k
C28
4700p
C26
0.047
C27
0.022
R22
0
C31
4700p
RV101
20k/20k
C21
220
4V
C114 0.22
C113 0.22
R25
47
C112
22
6.3V
C115
1
R109
470k
R110
100k
C106 C107
0.47 0.22
C119
1
R106
4.7k
R111
1k
R107
4.7k
Q102
2SB1689-T106
R108
1k
L101
Q103
DTC144TUA
-T106
CN1
20P
14
14
L103
L102
Q2
2SC4081T106R
R12
10k
CF1
10.7MHz
R105
100k
C121 2200p
C17
0.01
R14
100
C105
4.7 10V
L6
C104
0.22
R11
22k
L104
D101
1SS302
-TE85L
SRF-MQ11
4-4. PRINTED WIRING BOARD – MICROCOMPUTER BOARD –
MICROCOMPUTER BOARD
•
: Uses unleaded solder.
MICROCOMPUTER BOARD
(SIDE A)
C
4
3
1
2
(SIDE B)
B
E
4
3
1
2
IC304
IC302
32
17
16
33
C
LIQUID
CRYSTAL DISPLAY
IC301
C
B
C
B
S301
E
E
MODE/ENTER
C
B
E
B
E
US
48
IC303
1
49
64
3
2
4
1
B
T201
C
EXCEPT US
E
X301
B
11
C
11
1-860-777- (11)
MAIN BOARD
CN1
(Page 13)
E
DX
1-860-777- (11)
B
S302
SENS
LOCAL
• Semiconductor
LCD
SHIELD
Location
Ref. No.
15
15
Location
D201
D202
D302
D303
F-2
D-2
F-12
G-14
IC301
IC302
IC303
IC304
D-5
C-3
E-12
C-2
Q201
Q202
Q301
Q302
Q304
Q305
Q306
E-2
D-1
D-12
D-12
F-13
B-11
G-5
SRF-MQ11
R324 10
4-5. SCHEMATIC DIAGRAM – MICROCOMPUTER BOARD –
CN301
20P
S302
R205
10
R307
10k
R304
4.7k
R301
100k
C302
0.22
R319
470k
R348
0
R308
1M
R309
10k
R320
470k
R303
10k
R342
470k
C306
1
R343
1k
C325
22
4V
R321
1k
C319
0.47
C320
1
C322
0.1
R318
470k
C305
0.1
C303
220p
Q301
2SC5846002S0
C304
1000p
R311
10k
R344 100k
C203
10p
Q306
DTC144TUA
-T106
C204
0.1
R203
100k
C205
1
Q201
2SC584600LS0
Q305
2SA2029T2L
Q202
2SC584600LS0
R345
1k
R331 1k
R204
47k
R332 1k
R312
1M
C310
47p
R316
100k
C324 1
R329 100k
C308
0.01
C313
0.1
C309
1
C323 0.1
R333 1k
R313
TP
1k
(RESET)
C311
10p
C314
10 6.3V
C316
0.1
R348
0
R202
47k
Q304
R327 2SB1462J- QR(TX).SO
1M
C201
0.22
R315 1k
IC302
XC61CN1002NR
R314 1k
C301
0.01
C202
10p
R346
10k
IC304
XC61CN1102NR
R302
10k
D303
RB520S
-30TE61
R347
0
R326
100k
Q302
2SC5846002S0
T201
R201
1k
D202
MAZS130008S0
R306
1M
R328
1k
R325
470k
D201
MA2711100LSO
C321
0.01
D302
RB521S
-30-TE61
S301
X301
75KHz
IC301
TC9329AFAG -603(S.D)
C315
0.1
R338
100k
R339
100k
R340
100k
R335
1k
R336 1k
C317
0.1
R337
1k
IC303
XC61CN0802NR
C318
0.1
16
16
R349
100
R350
100
C206
10
6.3V
SRF-MQ11
4-6. PRINTED WIRING BOARD – BATTERY BOARD –
•
: Uses unleaded solder.
BATTERY BOARD
RECHARGEABL
BATTERY
NI-MH 1PC, 1.2V
1
SPEAKER
L-CH
2
S501
C
S502
B
S501, S502
MEGA
BASS
E
ON
C
1
2
OFF
1
C
B
B
C
E
E
E
2
IC501
B
4
3
5
1
3
MAIN BOARD
(Page 13)
A
9
11
10
8
6
7
5
4
11
1-860-778- (11)
• Semiconductor
Location
J501
DC IN 4.5V
J502
AUDIO IN
17
17
Ref. No.
Location
D502
D504
D505
D506
D-2
E-6
G-5
E-6
IC501
E-8
Q501
Q502
Q503
Q504
C-3
D-3
D-4
E-3
SRF-MQ11
4-7. SCHEMATIC DIAGRAM – BATTERY BOARD –
L502
S501
R510
1k
S502
D505
1SS302-TE85L
C504
0.001
J502
L501
Q501
2SD2652T106
THP501
R505
47
Q502
2SB1474TL
R504
10
D504
RB521S-30-TE61
R503
10
D502
MAZS027008SO
IC501
XC6201P152MR
R501
1k
R515
1k
J501
CN501
2P
R502
1k
Q504
2SC4081T106R
Q503
2SA1576A-T106-R
C505
0.1
R508
4.7k
R512
47
C502
1
R509
100k
18
R513
0
R514
10k
R511
0
18
R516
47
C501
1
D506
1SS302-TE85L
SRF-MQ11
• IC BLOCK DIAGRAMS
TV RF OUT
FM RF OUT
AM BYPASS
AM RF IN
RFVCC
AM OSC
TV FM OSC
OSC OUT
MODE2
MODE1
IF REQ
IF COUNT
LPF2B
LPF2A
L OUT
IC1 TA2154AFN-EL (MAIN board)
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
AM
OSC
AM
MIX
1/2
FM
OSC
TV
OSC
SW
FM/AM/TV
PW SW
BUFF
1/8 or
1/16
BUFF
BUFF
LEVEL
DET
AM
DET
IF
BUFF
FM
DET
FM MIX
AM MIX
10
11
12
13
14
15
R OUT
RF GND
9
8
LPF1
FM RF IN
7
MPX IN
TV RF IN
6
FM MPX
DET OUT
5
QUAD
4
AM IF IN
3
FM IF IN
2
AGC
1
AF
AM
IF
FM
IF
AGC
GND
FM/TV
MIX
FM
RM
VCC
TV
RF
RF IN
VREF IN
RF OUT
BASE
VCC
OUT A
OUT C
PW GND
OUT B
AGC IN
AGC DET
OUTPUT SW
IC101 TA2179FNG (EL) (MAIN board)
24
23
22
21
20
19
18
17
16
15
14
13
RF & REF
PW
A
PW
C
PW
B
+
-
+
-
AGC DET
MODE SW
-
PW SW, PW MUTE, BST SW
BST
2
3
4
5
6
7
8
9
10
11
12
IN A
IN B
VREF
PW SW
PW MUTE
BST SW
GND
LPF
BST NF
BST OUT
PW INC
MONO/ST SW
+
1
19
SRF-MQ11
4-8. IC PIN FUNCTION DESCRIPTION
• IC301 TC9329AFAG-603 (S.D) (MICROCOMPUTER board) (LCD DRIVER, SYSTEM CONTROL)
Pin No.
Pin Name
I/O
Description
1 to 4
COM1 to COM4
O
LCD common output
5 to 13
S1 to S13
O
LCD segment output
14
S10
—
Not used (open)
15
S11(P8-0)
—
Not used (connected to ground terminal)
16 to 18
P8-1 to P8-3
—
Not used (connected to ground terminal)
19
P9-0(+)
I
+ key signal input
20
P9-0(-)
I
- key signal input
21
P9-2(ENTER/MODE)
I
ENTER/MODE key signal input
22
P9-3
—
Not used (connected to ground terminal)
23 to 25
P1-0 to P1-2
—
Not used (connected to ground terminal)
26
P1-3(DC IN)
I
27
VDD
—
Power supply terminal
28
P4-0(BEEP)
O
Beep sound output
29
P4-1
—
Not used (connected to ground terminal)
30
P4-2(CHARGE)
O
Charge control signal output (“L”:charge off “H”:charge on)
31
P4-3(MUTE)
O
Mute signal output (“L”:mute on “H”:mute off)
32
MUTE
—
Not used (connected to ground terminal)
33
TEST
—
Not used (connected to ground terminal)
34
INT2(POWER SW)
I
Power switch input (“L”:power on “H”:power off)
35
INT2(VDET1)
I
1.0 V battery voltage detection signal input (“L”:lower than 1.0V)
36
IF IN2
—
Not used (open)
37
GND
—
Ground terminal
38
OSC IN
I
39
VDD
—
Power supply terminal
Charger detect signal input
Programmable counter input terminal
40
D0
O
Phase comparator output
41
V REG
—
Not used (connected to ground terminal)
42
P3-0(POWER ON2)
O
Power supply control signal output (“L”:on)
43 to 45
P3-1 to P3-3
—
Not used (connected to ground terminal)
46
P5-0(A/D)
I
Charger voltage detection signal input
47
P5-1(SHIMUKE1)
I
Country set up 1 signal input
48
P5-2(SHIMUKE2)
I
Country set up 2 signal input
49
P5-3(WAIT)
I
Wait mode set up signal input
50
P2-0(POWER ON1)
O
Power supply control signal output (“H”:on)
1.1 V battery voltage detection signal input (“L”:lower than 1.1V)
51
P2-1(VDET2)
I
52 to 53
P2-2 to P2-3
—
54
RESET
I
Reset signal input
55
XOUT
O
External crystal resonator terminal (75kHz)
56
XIN
I
External crystal resonator terminal (75kHz)
57
GND
—
Ground terminal
58
VDB
—
Power voltage step up terminal (connected to ground terminal)
59
C1
—
Voltage double boosting capacitor terminal
60
C2
—
Voltage double boosting capacitor terminal
61
VEE
—
1.5 V constant voltage power supply output for LCD drive (connected to ground terminal)
62
C3
—
Voltage double boosting capacitor terminal
63
C4
—
Voltage double boosting capacitor terminal
64
VCLD
—
3.0 V constant voltage power supply output for LCD drive (connected to ground terminal)
20
Connected to ground terminal
SRF-MQ11
Ver. 1.2
SECTION 5
EXPLODED VIEWS
NOTE:
• -XX, -X mean standardized parts, so they may
have some differences from the original one.
• The mechanical parts with no reference number
in the exploded views are not supplied.
•
Items marked “*” are not stocked since they
are seldom required for routine service. Some
delay should be anticipated when ordering these
items.
•
Abbreviation
CET : East European and Russian models
FR : French model
HK : Hong Kong model
IT
: Italian model
SP : Singapore model
17
1
20
29
21
2
13
7
12
28
22
13
14
3
16
3
15
11
18
26
19
24
23
25
17
9
7
7
16
7
10
8
7
6
29
5
3
4
2
1
Ref. No.
Part No.
Description
1
2
3
4
5
3-265-621-01
3-262-916-01
3-252-824-11
3-262-915-01
1-828-150-11
PAD, EAR
HOLDER (DRIVER)
SCREW (1.4)
REAR (R), CABINET
WIRE, LEAD (11 CORE)
* 6
* 6
7
* 8
A-4547-349-A
A-4547-354-A
3-254-136-11
A-4547-347-A
* 8
9
10
11
12
13
Remarks
MAIN BOARD, COMPLETE (IT,FR)
MAIN BOARD, COMPLETE (EXCEPT IT,FR)
SCREW (B1.4)
MICROCOMPUTER BOARD, COMPLETE
(EXCEPT US)
A-4547-361-A MICROCOMPUTER BOARD, COMPLETE (US)
3-262-923-01
3-262-924-01
X-2021-350-1
3-262-927-01
3-244-722-01
COVER JOG
KNOB (DX/LOCAL)
CABINET (FRONT) ASSY (R)
CAP (R)
SCREW
Ref. No.
Part No.
Description
14
15
16
17
18
3-262-918-01
3-262-934-01
3-262-928-01
3-262-921-01
3-262-914-01
HANGER (R)
SPRING (R), TORSION
CHIP, HANGER
BASE (HANGER)
REAR (L), CABINET
19
19
20
21
22
X-2021-351-1
X-2021-352-1
3-262-933-01
3-262-917-01
3-262-926-01
BATTERY ASSY (EXCEPT US)
BATTERY ASSY (FOR US)(US)
SPRING (L), TORSION
HANGER (L)
CAP (L)
* 23
24
25
26
28
A-4547-353-A
3-262-925-01
X-2021-349-1
3-250-270-01
3-265-617-01
BATTERY BOARD, COMPLETE
KNOB (POWER)
CABINET (FRONT) ASSY (L)
SHEET (VOL), INSULATING
LABEL (DIA. 13), RBRC (US)
29
Remarks
1-542-561-11 DRIVER (030F038)
21
SRF-MQ11
BATTERY
SECTION 6
ELECTRICAL PARTS LIST
MAIN
NOTE:
• Due to standardization, replacements in the
parts list may be different from the parts
specified in the diagrams or the components
used on the set.
• -XX, -X mean standardized parts, so they
may have some difference from the original
one.
• Items marked “*” are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
• CAPACITORS:
uF: µF
•
•
•
RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
COILS
uH: µH
SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
Description
Remarks
Ref. No.
•
Accessories are given in the last of this parts
list.
Abbreviation
HK : Hong Kong model
SP : Singapore model
When indicating parts by reference number,
please include the board name.
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Ref. No.
Part No.
*
A-4547-353-A BATTERY BOARD, COMPLETE
************************
R511
R512
1-218-990-11 SHORT CHIP
1-216-805-11 METAL CHIP
0
47
5%
1/16W
3-267-308-01 CUSHION (BATT)
R513
R514
R515
R516
1-218-990-11
1-218-965-11
1-218-953-11
1-216-805-11
0
10K
1K
47
5%
5%
5%
1/16W
1/16W
1/16W
< CAPACITOR >
C501
C502
C504
C505
1-115-156-11
1-115-156-11
1-164-937-11
1-125-777-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
1uF
0.001uF
0.1uF
10V
10V
10.00% 50V
10.00% 10V
Part No.
•
Description
SHORT CHIP
RES-CHIP
RES-CHIP
METAL CHIP
Remarks
< SWITCH >
S501
S502
1-762-935-41 SWITCH, SLIDE (MEGA BASS/ON/OFF)
1-692-605-31 SWITCH, SLIDE (MEGA BASS/0N/OFF)
< CONNECTOR >
< THERMISTOR >
CN501
1-778-506-21 PIN, CONNECTOR (PC BOARD) 2P
TH501 1-533-808-11 IC LINK
************************************************************
< DIODE >
D502
D504
D505
D506
8-719-056-58
8-719-071-34
8-719-820-41
8-719-820-41
DIODE
DIODE
DIODE
DIODE
MAZS027008SO
RB521S-30-TE61
1SS302-TE85L
1SS302-TE85L
*
A-4547-349-A MAIN BOARD, COMPLETE (AEP)
**************************
*
A-4547-354-A MAIN BOARD, COMPLETE (US,UK,SP,HK)
*********************************
< IC >
< CAPACITOR >
IC501
6-705-761-01 IC XC6201P152MR
< JACK >
J501
J502
1-818-187-11 JACK,DC (POLARITY UNIFIED TYPE)
(DC IN 4.5V !)
1-817-380-11 JACK (AUDIO IN)
< COIL >
L501
L502
1-412-987-31 INDUCTOR
1-412-987-31 INDUCTOR
4.7uH
4.7uH
< TRANSISTOR >
Q501
Q502
Q503
Q504
6-550-364-01
8-729-043-97
8-729-026-52
8-729-905-35
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SD2652T106
2SB1474TL
2SA1576A-T106-R
2SC4081T106R
< RESISTOR >
R501
R502
R503
R504
R505
1-218-953-11
1-218-953-11
1-216-797-11
1-216-797-11
1-216-805-11
R508
R509
R510
1-218-961-11 RES-CHIP
1-218-977-11 RES-CHIP
1-218-953-11 RES-CHIP
22
RES-CHIP
RES-CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
1K
10
10
47
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
4.7K
100K
1K
5%
5%
5%
1/16W
1/16W
1/16W
C1
C2
C4
C6
C8
1-115-416-11
1-115-416-11
1-164-840-11
1-115-416-11
1-164-882-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
1PF
0.001uF
220PF
5.00%
5.00%
0.25PF
5.00%
5.00%
25V
25V
50V
25V
16V
C9
C13
C14
C15
C16
1-164-844-11
1-164-943-11
1-125-777-11
1-164-937-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
4PF
0.01uF
0.1uF
0.001uF
0.01uF
0.25PF
10.00%
10.00%
10.00%
10.00%
50V
16V
10V
50V
16V
C17
* C19
C20
C21
C22
1-164-943-11
1-107-820-11
1-137-859-11
1-137-859-11
1-115-156-11
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
TANTAL. CHIP
CERAMIC CHIP
0.01uF
0.1uF
220uF
220uF
1uF
10.00% 16V
16V
20%
4V
20%
4V
10V
C23
C25
C26
C27
C28
1-115-156-11
1-125-891-11
1-119-923-11
1-107-819-11
1-164-941-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
0.47uF
0.047uF
0.022uF
0.0047uF
10.00%
10.00%
10.00%
10.00%
C29
C30
C31
C34
C101
1-165-128-11
1-165-128-11
1-164-941-11
1-164-943-11
1-135-210-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
0.22uF
16V
0.22uF
16V
0.0047uF 10.00% 16V
0.01uF
10.00% 16V
4.7uF
20%
10V
10V
10V
10V
16V
16V
SRF-MQ11
MAIN
Ref. No.
Part No.
Description
C102
C103
C104
C105
C106
1-135-149-21
1-135-259-11
1-115-467-11
1-135-210-11
1-113-619-11
TANTALUM CHIP
TANTAL. CHIP
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
2.2uF
10uF
0.22uF
4.7uF
0.47uF
Remarks
C107
* C108
C109
C110
C111
1-165-128-11
1-107-820-11
1-164-156-11
1-164-156-11
1-164-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.22uF
0.1uF
0.1uF
0.1uF
0.1uF
16V
16V
25V
25V
25V
C112
C113
C114
C115
C116
1-119-750-11
1-165-128-11
1-165-128-11
1-115-156-11
1-115-156-11
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22uF
0.22uF
0.22uF
1uF
1uF
20.00% 6.3V
16V
16V
10V
10V
C117
C118
C119
C120
C121
1-115-156-11
1-127-569-91
1-115-156-11
1-164-939-11
1-164-939-11
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
100uF
20%
1uF
0.0022uF 10.00%
0.0022uF 10.00%
20%
20.00%
10.00%
20%
Ref. No.
10V
6.3V
10V
10V
10V
10V
4V
10V
50V
50V
1-813-214-21 FILTER, CERAMIC 10.7MHz
1-795-410-21 FILTER, CERAMIC 10.7MHz
< CONNECTOR >
* CN1
1-793-568-21 CONNECTOR, BOARD TO BOARD 20P
< TRIMMER >
CT1
Description
Remarks
< RESISTOR >
< FILTER >
CF1
CF2
Part No.
MICROCOMPUTER
1-141-615-21 CAP, ADJ
R1
R2
R4
R5
R9
1-218-977-11
1-218-977-11
1-218-981-11
1-218-977-11
1-218-990-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
SHORT CHIP
100K
100K
220K
100K
0
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
R11
R12
R13
R14
R15
1-218-969-11
1-218-965-11
1-218-985-11
1-218-941-81
1-218-953-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
22K
10K
470K
100
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R17
R18
1-218-953-11 RES-CHIP
1-218-969-11 RES-CHIP
1K
22K
R18
1-218-973-11 RES-CHIP
47K
R19
1-218-969-11 RES-CHIP
22K
R19
1-218-973-11 RES-CHIP
47K
5%
1/16W
5%
1/16W
(US,UK,SP,HK)
5%
1/16W
(AEP)
5%
1/16W
(US,UK,SP,HK)
5%
1/16W
(AEP)
R20
R21
R22
R23
1-218-990-11
1-208-635-11
1-218-990-11
1-218-969-11
0
10
0
22K
R23
1-218-990-11 SHORT CHIP
0 (US,UK,SP,HK)
R24
1-218-969-11 RES-CHIP
22K
R24
R25
R101
R102
1-218-990-11
1-218-937-11
1-218-981-11
1-220-803-81
SHORT CHIP
RES-CHIP
RES-CHIP
RES-CHIP
0 (US,UK,SP,HK)
47
5%
220K
5%
4.7
5%
1/16W
1/16W
1/16W
R103
R104
R105
R106
R107
1-220-803-81
1-220-803-81
1-218-977-11
1-218-961-11
1-218-961-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
4.7
4.7
100K
4.7K
4.7K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R108
R109
R110
R111
1-218-953-11
1-218-985-11
1-218-977-11
1-218-953-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
470K
100K
1K
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
SHORT CHIP
RES-CHIP
SHORT CHIP
RES-CHIP
5%
1/16W
5%
1/16W
(AEP)
5%
1/16W
(AEP)
< DIODE >
D1
D2
D3
D101
8-719-076-23
8-719-076-23
8-719-076-23
8-719-820-41
DIODE
DIODE
DIODE
DIODE
HVC202B TRU
HVC202B TRU
HVC202B TRU
1SS302-TE85L
< IC >
IC1
IC101
6-703-664-01 IC TA2154AFN-EL
6-705-694-01 IC TA2179FNG(EL)
< COIL >
L1
L3
L6
L101
L102
1-456-689-21
1-414-684-11
1-412-975-31
1-412-987-31
1-412-987-31
COIL, RF
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
L103
L104
1-412-987-31 INDUCTOR
1-412-987-31 INDUCTOR
< VARIABLE RESISTOR >
27nH
0.47uH
4.7uH
4.7uH
4.7uH
4.7uH
RV101 1-227-637-21 RES, VAR, CARBON 20K (VOL
)
************************************************************
*
A-4547-347-A MICROCOMPUTER BOARD, COMPLETE
(AEP,UK,SP,HK)
**************************************
*
A-4547-361-A MICROCOMPUTER BOARD, COMPLETE (US)
***********************************
< TRANSISTOR >
Q2
Q3
Q101
Q102
Q103
8-729-905-35
8-729-423-52
6-550-044-01
6-550-044-01
8-729-029-15
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2SC4081T106R
2SC3931-C-TX
2SB1689-T106
2SB1689-T106
DTC144TUA-T106
1-780-107-11
1-805-518-11
3-262-922-01
3-267-306-01
CONDUCTIVE BOARD, CONNECTION
DISPLAY PANEL, LIQUID CRYSTAL
HOLDER (LCD)
SHEET, COPPER LEAF
23
SRF-MQ11
MICROCOMPUTER
Ref. No.
Part No.
Description
Remarks
< CAPACITOR >
C201
C202
C203
C204
C205
1-165-128-11
1-164-850-11
1-164-850-11
1-164-156-11
1-115-156-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.22uF
10PF
10PF
0.1uF
1uF
16V
0.50PF 50V
0.50PF 50V
25V
10V
C206
C301
C302
C303
C304
1-117-919-11
1-164-943-11
1-127-715-91
1-164-882-11
1-164-937-11
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
0.01uF
0.22uF
220PF
0.001uF
20.00%
10.00%
10%
5.00%
10.00%
* C305
C306
C308
C309
C310
1-107-820-11
1-115-156-11
1-164-943-11
1-115-156-11
1-164-866-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
1uF
0.01uF
1uF
47PF
16V
10V
10.00% 16V
10V
5.00% 50V
C311
* C313
C314
* C315
* C316
1-164-850-11
1-107-820-11
1-135-259-11
1-107-820-11
1-107-820-11
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
CERAMIC CHIP
CERAMIC CHIP
10PF
0.1uF
10uF
0.1uF
0.1uF
0.50PF 50V
16V
20.00% 6.3V
16V
16V
* C317
* C318
C319
C320
C321
1-107-820-11
1-107-820-11
1-113-619-11
1-115-156-11
1-164-943-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.47uF
1uF
0.01uF
16V
16V
10V
10V
10.00% 16V
* C322
* C323
C324
C325
1-107-820-11
1-107-820-11
1-115-156-11
1-127-895-91
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTAL. CHIP
0.1uF
0.1uF
1uF
22uF
20%
6.3V
16V
16V
16V
50V
16V
16V
10V
4V
< CONNECTOR >
* CN301
1-793-567-21 CONNECTOR, BOARD TO BOARD 20P
Ref. No.
Part No.
Description
Remarks
R203
R204
R205
1-218-977-11 RES-CHIP
1-218-973-11 RES-CHIP
1-208-635-11 RES-CHIP
100K
47K
10
5%
5%
5%
1/16W
1/16W
1/16W
R301
R302
R303
R304
R306
1-218-977-11
1-218-965-11
1-218-965-11
1-218-961-11
1-218-989-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100K
10K
10K
4.7K
1M
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R307
R308
R309
R311
R312
1-218-965-11
1-218-989-11
1-218-965-11
1-218-965-11
1-218-989-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
10K
1M
10K
10K
1M
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R313
R314
R315
R316
R318
1-218-953-11
1-218-953-11
1-218-953-11
1-218-977-11
1-218-985-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
1K
1K
100K
470K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R319
1-218-985-11 RES-CHIP
470K
5%
R320
1-218-985-11 RES-CHIP
470K
R321
R324
R325
1-218-953-11 RES-CHIP
1-208-635-11 RES-CHIP
1-218-985-11 RES-CHIP
1K
10
470K
1/16W
(US)
5%
1/16W
(AEP,UK,SP,HK)
5%
1/16W
5%
1/16W
5%
1/16W
R326
R327
R328
R329
R331
1-218-977-11
1-218-989-11
1-218-953-11
1-218-977-11
1-218-953-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100K
1M
1K
100K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R332
R333
R335
R336
R337
1-218-953-11
1-218-953-11
1-218-953-11
1-218-953-11
1-218-953-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
1K
1K
1K
1K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R338
R339
R340
R342
R343
1-218-977-11
1-218-977-11
1-218-977-11
1-218-985-11
1-218-953-11
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
RES-CHIP
100K
100K
100K
470K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R344
R345
R346
R347
R348
1-218-977-11
1-218-953-11
1-218-965-11
1-218-990-11
1-218-990-11
RES-CHIP
RES-CHIP
RES-CHIP
SHORT CHIP
SHORT CHIP
100K
1K
10K
0
0
5%
5%
5%
1/16W
1/16W
1/16W
R349
R350
1-218-941-81 RES-CHIP
1-218-941-81 RES-CHIP
100
100
5%
5%
1/16W
1/16W
< DIODE >
D201
D202
D302
D303
6-500-299-01
8-719-056-60
8-719-071-34
8-719-069-29
DIODE
DIODE
DIODE
DIODE
MA2711100LS0
MAZS130008SO
RB521S-30-TE61
RB520S-30TE61
< IC >
IC301
IC302
IC303
IC304
6-804-267-01
8-759-690-96
6-701-978-01
8-759-690-97
IC
IC
IC
IC
TC9329AFAG-603(S.D)
XC61CN1002NR
XC61CN0802NR
XC61CN1102NR
< TRANSISTOR >
Q201
Q202
Q301
Q302
Q304
6-550-237-01
6-550-237-01
6-550-237-01
6-550-237-01
8-729-037-53
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Q305
Q306
6-550-132-01 TRANSISTOR
8-729-029-15 TRANSISTOR
2SC584600LS0
2SC584600LS0
2SC584600LS0
2SC584600LS0
2SB1462J-QR(TX).SO
< SWITCH >
S301
S302
1-786-034-21 SWITCH, LEVER (SLIDE) (MODE/ENTER)
1-572-922-11 SWITCH, SLIDE (SENS)
< TRANSFORMER >
2SA2029T2L
DTC144TUA-T106
T201
< VIBRATOR >
< RESISTOR >
R201
R202
24
1-218-953-11 RES-CHIP
1-218-973-11 RES-CHIP
1-435-731-21 TRANSFORMER, DC/DC CONVERTER
1K
47K
5%
5%
1/16W
1/16W
X301
1-767-388-21 VIBRATOR, CRYSTAL 75kHz
************************************************************
SRF-MQ11
Ver 1.1
Ref. No.
Part No.
Description
Remarks
Ref. No.
Part No.
Description
Remarks
MISCELLANEOUS
**************
5
1-828-150-11 WIRE, LEAD (11 CORE)
ACCESSORIES
************
0
0
0
0
1-477-828-13
1-477-830-13
1-477-831-13
1-477-919-13
1-828-148-11
ADAPTOR, AC (AC-E45TR1)(IT,FR,CET,SP)
ADAPTOR, AC (AC-E45TR1)(AUS)
ADAPTOR, AC (AC-E45TR1)(US)
ADAPTOR, AC (AC-E45TR1)(UK,HK)
CORD (WITH PLUG)(SP-SP)(EXCEPT US)
1-828-149-11 CORD (WITH PLUG)(SP-L)(US)
3-263-781-11 MANUAL, INSTRUCTION
(ENGLISH,FRENCH,GERMAN,SPANISH,CHINESE)
3-263-781-21 MANUAL, INSTRUCTION
(DUTCH,ITALIAN,PORTUGUESE,SWEDISH,FINNISH)(AEP)
3-263-781-31 MANUAL, INSTRUCTION (RUSSIAN)(IT,FR)
The components identified by mark 0 or dotted
line with mark 0 are critical for safety.
Replace only with part number specified.
25
SRF-MQ11
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver.
Date
Description of Revision
1.0
2004.06
New
1.1
2004.06
Addition of East European, Russian and Australian models
1.2
2005.03
Addition of Ref.No. 29 (DRIVER)
(SPM-05042)