EGGER Compact Laminate Collection

Transcription

EGGER Compact Laminate Collection
Egger Compact Laminate Collection
A durable and design focused
solution for interiors.
CONTENTS
03 EGGER Compact Laminate
14 Product overview
16Textures
18 Uni colours
18 Neutral uni colours
21 Natural uni colours
22 Intensive uni colours
24 Woodgrain reproductions
24 Classic & modern
30Artwood
31Authentic
34Exotic
36 Material reproductions
36 Stone & mineral
37 Textile & leather
38 Used Look
39Metal
40 Texture meets colour
41 Processing instructions
41 Storage
42Processing
44Fabrication
48Application
59 Technical data
60 Cleaning & maintenance
60 Waste treatment
61Service
62 Availability guide –
Full product overview
EGGER Compact Laminate 3
EGGER COMPACT LAMINATE:
ELEGANT AND ROBUST
The appeal of Egger Compact Laminate is not just down to the attractive designs and textures. Its durability and
moisture resistance open up a new range of interior design opportunities.
Compact Laminate is particularly suitable for interior applications subjected to high stress,
as well as areas where there may be an extra requirement for hygiene standards, such as in restaurants,
or hospitals.
It is also used in wet areas, such as in bathrooms, sanitary facilities, and changing rooms.
It is the combination of durability and sleek design that makes Compact Laminate
so interesting for a variety of solutions within the commercial interiors market.
Characteristics
• Sleek and elegant design
• Hard-wearing and impact resistant surface
• No edge or surface finish required
• Homogeneous material for precise processing
• Very high stability
• Moisture resistant
• Hygienic and easy to maintain
• Resistant to common cleaning products and chemicals
www.egger.com/compactlaminate
4 EGGER Compact Laminate
HIGH PERFORMANCE WITH
DESIGN FLEXIBILITY
As well as being easy to clean and maintain, compact laminate has long term durability and robustness
making it the go to product for many design projects. EGGER Compact Laminate is ideal for wet areas or
high stress areas such as tables, worktops, wall panelling, changing rooms and partitions. This product
will help you bring unique designs into rooms where it was not possible before.
talsee.ch
EGGER Compact Laminate 5
USE FRENCH IMAGE
W1000 ST9 Premium White, U337 ST9 Fuchsia
6 EGGER Compact Laminate
The surface of EGGER Compact Laminate can be
routered to create tailored designs.
F425 ST10 Beige Linen
EGGER Compact Laminate 7
DESIGNED TO THE CORE
The homogeneous core of EGGER Compact Laminate is ideally suited to
precision processing, opening up the possibilities for bespoke design.
The board can be milled, routered, grooved as well as drilled - there are
few limits. Any part of the board can be milled or routered, given no
additional edge finishing process is neccessary.
Not only is it possible to specify the surface finish, but selecting a black
or a white core can give your furniture a completely different look.
8 EGGER Compact Laminate
Sleekness and durability - one does not exclude the other.
SLEEK AND CONTEMPORARY
Combining both strength and a slimline material means areas where a thicker materials may have been required can now be
elegant thin designs. Not only can this be done in a solid colour but also with authentic woodgrain and alternatives to metals.
EGGER Compact Laminate 9
TAKE ADVANTAGE OF A
VERSATILE PRODUCT
EGGER Compact Laminate is great for any creative design
idea thanks to its properties and processing possibilities
in particular. Break new ground with your
furniture, such as this stool, that became an innovative
furniture item. Using pieces of EGGER Compact Laminate
and having the core as a feature, creates a durable design
led piece.
W1200 ST2 Porcelain
Discover the uni colours, woodgrain and material
reproductions of the Zoom Collection at
www.egger.com/zoom.
Picture:
Photographic workshop
Katharina Jäger
10 EGGER Compact Laminate
SYNCHRONISED PORE
COMPACT LAMINATE
EGGER is the first in the world to offer synchronised pore decors on a
compact laminate. The Feelwood decors use the latest technology to
align grain pattern with the surface texture of the board. These
woodgrain decors take a step closer to appearing like a real wood
and create an even more authentic finish.
The Feelwood range can offer benefits which are not available when
using real wood. Panels can be replaced without the fear they will
not match with the remaining furniture or panelling and there is also
a higher resistance and durability.
EGGER Compact Laminate 11
© Nicolas Tarantino
A SOLUTION FOR ALL PROJECTS
ST27 is a classical yet modern design. The soft planking
and texture of the Tortona decor gives an authentic
appearance.
ST28 is a rustic decor, the knots and planking of
Synchronised pore decors are also
the Gladstone decors create a natural feel which is
available in Laminate and melamine
highlighted by the sandblasted decors.
faces panels.
Discover the latest decors at
ST29 is ideal for large surfaces as the dramatic grain
www.egger.com/zoom
pattern gives a sophisticated and elegant finish.
12 EGGER Compact Laminate
STAY CO-ORDINATED
Compact laminate is part of our matching decor and texture range. This allows
you to combine a variety of EGGER products within a design: Decors
available as compact laminates can also be supplied as melamine faced boards,
lightweight boards, laminates and edging. Please see our online availability guide
at www.egger.com/downloads.
Let your ideas take shape with our VDS software. The Virtual Design Studio
offers you an almost unlimited variety in terms of design and visualization
of your projects. Place the EGGER standard decors into more than 80 room
sets and visualise your own ideas.
www.egger.com/vds
EGGER Compact Laminate 13
The EGGER range of matching decors and textures allows
you to mix and match decors and materials from of the
Zoom collection.
H1277 ST9 Lakeland Acacia, U330 ST9 Aubergine
14 EGGER Compact Laminate
PRODUCT OVERVIEW
EGGER Compact Laminate is available with a black or white core. It is produced
using multiple layers of phenolic resin impregnated core papers and melamine
resin impregnated decor papers. The layers are fused together under high
pressure and temperature. Due to its construction compact laminate is ideal for
high traffic areas.
EGGER Compact Laminate performs to EN 438 and is used for many
applications such as wall panelling, cubicles, partitions, kitchen worktops and
offices as well as other high traffic areas such as hotel rooms and retail spaces.
A flame retardant range is also available. EGGER Compact Laminate Flammex
Euroclass B is classified as B-s2, d0 and conforms to EN 13501-1. Flammex is
used in areas where there is an increased requirement for fire protection such
as airports or hospitals.
EGGER Compact Laminate 15
COMPOSITION OF A COMPACT LAMINATE
1
2
3
4
1
Overlay (optional) 1)
2
Decorative impregnated paper
3
Sodium kraft papers
4
Decorative impregnated paper
5
Overlay (optional) 1)
5
1)
Compact laminates with printed decors (wood and material reproductions) are enhanced with overlay.
PRODUCT OVERVIEW AND CLASSIFICATION
Within the EN 438 Standard, compact laminates are differentiated and classified by three letters – also referred to as the
classification system. The following gives an overview of the material types offered by EGGER as standard.
Size
2790 × 2060 mm (alternatives 5600 × 2060 mm)
Thickness
3, 4, 5, 6, 8, 10, 12 and 13 mm
Core colour
Black or white
Material type
A wid
e rang
e
availa
ble fro
m
2 boar
ds
Standard decors: CGS(Black core standard grade)
Standard decors: CGF (Flame retardant grade)
Standard decors: BCS (White core standard grade)
Pearlescent decors: ACS (Black core standard grade)
Pearlescent decors: ACF (Flame retardant grade)
AVAILABILITY
Details relating to the complete matching products availability
guide can be found from page 61, or visit: www.egger.com/zoom
Eurodekor melamine faced chipboard
Laminate
Door Size Laminates
Compact laminates interior
ABS Edging
16 EGGER Compact Laminate
TEXTURE INNOVATION
With ZOOM every decor uses the most appropriate surface texture, ensuring that our decorative materials both
look and feel like the real thing.
NEW
Synchronised pore
ST27 FEELWOOD Elegance – The fine and linear, yet natural texture is
synchronised with the grain of the Tortona decor to create an incredibly
realistic finish.
NEW
Synchronised pore
ST28 FEELWOOD Nature – This texture is characterised by its authentic
feel. The synchronised knots and planking create a natural feel reminiscent
of solid wood.
NEW
Synchronised pore
ST29 FEELWOOD Ambiance – The synchronised texture has a striking yet
elegant appearance. It is ideal for large applications to create a tasteful,
sophisticated feel. It traces the grain with soft recesses, creating a tactile effect.
NEW
ST87 Ceramic – The matt-gloss effect simulate the surface and feel of a
ceramic plate helping to create visual depth.
EGGER Compact Laminate 17
ST9 Perfect Matt – Used with uni colours and woodgrains to offer a
soft, natural feel. This texture is ideal for the current trend for matt
surfaces.
ST10 Authentic – A highly authentic and realistic surface texture for
natural, distinctive and rustic decors. The perfect surface for solid wood
reproductions.
ST15 Office – A smooth flat surface finish with low gloss levels and low
maintenance. Combines with intensive uni colours and a wide variety of
woodgrains.
ST22 Matex – Thanks to its feel and matt gloss effect, it give linear and
lively woodgrain decors more naturalness and depth for a more realistic
wood-like finish.
ST18 Waveline * – The horizontal surface texture offers new levels of depth,
has a modern appearance and is reminiscent of solid wood which has been
routed out and then painted or lacquered.
* from 8 mm and identical surface texture on both sides
ST2 Diamond – Has a grainy, mini-pearl texture, with a medium gloss
level. This surface is robust, very durable and used with solid colours
and pearlescent decors.
18 EGGER Compact Laminate
NEUTRAL UNI COLOURS
Basic colours in white, beige, brown, grey and black tones - timeless, universal and flexible.
W1000 ST2
Premium White
ST9
Premium White
ST18
Premium White
ST22
Premium White
W1200ST2 Porcelain
ST9Porcelain
W980
ST2
Platinum White
ST15
Platinum White
W908
ST2
Basic White
W911
ST2
Cream White
ST15
Cream White
U224 ST15Silk
U216 ST15Oyster
U222 ST15Crema
U104 ST15Alabaster
U108 ST15Vanilla
U113 ST15Cotton
NEW
U702ST9Cashmere
U750
ST9
Taupe Grey
U775
ST15
White Grey
U708
ST15
Light Grey
U763
ST15
Pearl Grey
ST18
Pearl Grey
U765
ST15
Silver Grey
U732
ST15
Dust Grey
U963
ST15
Diamond Grey
U156
ST9
Sand Beige
U727
ST9
Stone Grey
ST22 Stone Grey
U206ST9 Malaga
U808ST9 Mocha
U803
ST15
Black Brown
U795
ST9
Brown Grey
U748ST9 Truffle
NEW
U631ST9Olive
U730ST9Basalt
U741ST9Lava
ST22Lava
U961ST2Graphite
U999ST2 Black
ST18Black
Neutral uni colours
for a calming
and modern atmosphere
EGGER Compact Laminate Laminate 21
21
NATURAL UNI COLOURS
A selection of pastels and chalk colours, ideal for combinations thanks to their subtle tone and soft,
matt appearance.
U107
ST9
Velvet Yellow
U204ST9 Camel
U334ST9 Powder
NEW
U343ST9 Vino
U807ST9 Nougat
U617ST9Wasabi
U635ST9Moss
U701ST9Platinum
U518
ST9
Ice Blue
U539
ST9
Steel Blue
U336ST9 Orchid
U337ST9Fuchsia
U330ST9 Aubergine
22 EGGER Compact Laminate
INTENSIVE
Bright, eye-catching primary colours with a strong, bold appearance.
U129
ST15
Sun Yellow
U143
ST15
Signal Yellow
U146
ST15
Maize Yellow
U114 ST15Yellow
U634
ST15
Velvet Green
U625
ST15
Apple Green
U630
ST15
Lime Green
U632
ST15
Grass Green
U628 ST15Green
U535 ST15Aqua
U536 ST15Lagoon
U633 ST15Turquoise
U538 ST15Ocean
U533
ST15
Polar Blue
U522 ST15Horizon
U537
ST15
Brilliant Blue
U514
ST15
Baltic Blue
U525 ST15Blue
U506 ST15Marine
U329 ST15Manderine
U332 ST15Orange
U328 ST15Lipstick
U321 ST15Red
U323
ST15
Chilli Red
U311 ST15Burgundy
24 EGGER Compact Laminate
CLASSIC & MODERN
A mix of our best selling classic woodgrains and newer modern alternatives.
H3758 ST9
Helsinki Birch
H1867 ST9
Cream Canadian Maple
H1733
ST9
Mainau Birch
EGGER Compact Laminate 25
H1521ST15Maple
H1887 ST9
Natural Starnberg Maple
H3911
ST9
Natural Tauern Beech
H1518
Natural Beech
H1582 ST15
Ellmau Beech
H1511
ST15
Bavarian Beech
Natural Tyrolean Beech
H3662 ST9
Natural Venetian Cherry
H1615
ST9
Romana Cherry
ST15
H1920 ST9
26 EGGER Compact Laminate
H1706ST15 Cherry
H1502ST15 Alder
H3113
Lindau Pearwood
H1950 ST15
Natural Calvados
Natural Dijon Walnut
H3775 ST9
Light Tennessee Walnut
ST15
H3734 ST9
H1951
ST15
H3704 ST15
Sienna Calvados
Tobacco Aida Walnut
EGGER Compact Laminate 27
NEW
NEW
Synchronised pore
Synchronised pore
H3760 ST29 White Cape Elm Also available as ST9
H3766
H3755 ST22
H1484 ST22 Brown Grey Avola
H1476 ST22 Champagne Avola
H1424 ST22 Woodline cream
H1428 ST22 Woodline mocha
H1474
White Swiss Larch
ST22 White Avola
ST29
Dark Brown Cape Elm Also available as ST9
H1277
ST9
Light Lakeland Acacia
28 EGGER Compact Laminate
H3304 ST9
Grey Lacquered Chateau Oak
H3306 ST9
Anthracite Chateau Oak
H3363 ST9
Anthracite Highland Oak
H1334 ST9
Light Ferrara Oak
NEW
Synchronised pore
H1793 ST27
Lava Tortona
Also available as ST9
Modern classics
for a homely
atmosphere.
NEW
Synchronised pore
H1796 ST27
Natural Tortona
Also available as ST9
H1298 ST22 Sand Lyon Ash
H3778 ST9
H3400 ST22 Rustic Pine
H1487 ST22 Bramberg Pine
H1215
H3128 ST15
ST22 Brown Cassino Ash
Natural Caribbean Walnut
Natural Plum
H3129 ST9
Autumn Plum
30 EGGER Compact Laminate
ARTWOOD
Influenced by real wood, but given an exciting new interpretation by changing the grain pattern.
H3078 ST22
F584
Hacienda White
ST22 Fino cinnamon
H3081 ST22 Hacienda Black
F583
ST22 Fino Bronze
EGGER Compact Laminate Laminate 31
31
AUTHENTICS
A new generation of woodgrains in natural colour tones with knots, cracks and a strong, authentic character.
H1146
ST10
Grey Bardolino Oak
H1372
H1145
ST10
Natural Bardolino Oak
H3303 ST10
ST22 Natural Aragon Oak
Natural Arlington Oak
H3331
ST10
H3332 ST10
Natural Nebraska Oak
Grey Nebraska Oak
NEW
Synchronised pore
H3309 ST28 Sand Gladstone Oak Also available as ST9
NEW
NEW
Synchronised pore
H3326 ST28 Grey Beige Gladstone Oak
Also available as ST9
Synchronised pore
H3325 ST28 Tobacco Gladstone Oak
Also available as ST9
EGGER Compact Laminate 33
H1150
ST10
Grey Authentic Oak
H3753 ST22 Country Montana Larch
H1151ST10
Brown Authentic Oak
H3700ST10
Natural Pacific Walnut
Furniture with visible
cracks and knots create
an authentic atmosphere.
H3114
ST9
Tirano Pearwood
34 EGGER Compact Laminate
EXOTICS
Eye-catching woodgrains with a distinctive, individual character.
H3012 ST22 Coco Bolo
H3006 ST22
Sand Zebrano
H3005 ST22
Grey Beige Zebrano
H3082ST22 Amazonas
FOR VISUALISATION PURPOSES
The small images give you a close-up view of the decor surfaces. They
correspond to a section of 900 x 600 mm.
H3031 ST9
Dark Cordoba Olive
H3090ST22 Driftwood
H3025ST15 Macassar
H3058 ST22
Mali Wenge
36 EGGER Compact Laminate
STONE & MINERAL
Authentic reproductions of man-made, natural stone & minerals.
F396
F210
ST10
ST9
Basaltino Grey
White Amalvi Marble
F236
F211
ST15 Terrano Grey
ST9
Brown Amalvi Marble
F276
ST9
Arkosa Sand
F274
ST9
Light Concrete
F275
ST9
Dark Concrete
EGGER Compact Laminate 37
TEXTILE & LEATHER
Soft, natural materials and designs which appear like the real thing.
F428
ST10
Brown Leather
F425
ST10
Beige Linen
F426
ST10
Grey Linen
38 EGGER Compact Laminate
USED LOOK
Materials with signs of use and weathering help to create a vintage look. Although pure
and linear designs remain a key trend, the use of materials which show character and
imperfection are increasing being demanded.
F636
ST15
F633
Titanium Blue Metallo
ST15
Grey Brown Metallo
NEW
F310
ST87 Rust Ceramic
NEW
F311
ST87 Anthracite Ceramic
EGGER Compact Laminate Laminate 39
39
METALS
Warm and cool interpretations of metal, each with a high quality, pearlescent surface finish.
F501 ST2Titanium
F784
ST2
Stainless Steel Microline
F509ST2Aluminium
F447
ST2
Quartz Lava
40 EGGER Compact Laminate
TEXTURE MEETS COLOUR
Deep textures or matt gloss effect are applied to solid colours to give exciting fantasy patterns.
W1000 ST18
Premium White
W1000 ST18
Premium White
U763
Pearl grey
ST18
U999 ST18Black
W1000 ST22
U727
W1000 ST22
Premium White
Premium White
ST22 Stone Grey
U741 ST22Lava
EGGER Compact Laminate EGGER Compact Laminate 41 e 41
PROCESSING INSTRUCTIONS
1. STORAGE
EGGER compact laminate must be stored in enclosed, dry areas at approximately 18°C to 25°C and a relative humidity of
approximately 50% to 65%. After removal of the original packaging, the compact laminate should be stored stacked horizontally on
a sturdy, flat and level base board of equal or greater dimension. Direct floor contact and/or exposure to sunlight must be avoided
at all times. The top board should be covered with a laminated protective board (not raw chipboard) of at least equal or greater
dimension (see Figure 1). Where horizontal storage is not possible, the compact laminate sheets should be stored at an angle of
approximately 80°, in an inclined rack, providing support to the surface area and ends (see Fig.2). A laminated protective cover
board of at least equal dimension is also required for vertical storage.
Figure 1
Right
Wrong
Figure 2
Incorrect storage can result in permanent distortion of the board.
42 EGGER Compact Laminate
1.1. Handling
After removing the packaging and prior to processing, the compact
laminates should be inspected for visible damage. In view of the relatively
heavy weight, special care is required when transporting and handling
compact laminates. As a rule, all persons transporting and/or handling
compact laminates should wear personal safety equipment such as gloves,
safety footwear and suitable work wear. The sheets have to be lifted up;
pushing or dragging the decorative sides over one another should be
avoided (see Figure 3).
Figure 3
1.2. Conditioning
Compact laminates react to changes in ambient conditions with a certain amount of dimensional movement. For this reason, the
storage and processing conditions should correspond as closely as possible to the prevailing conditions where the material will be
subsequently used. Prior to installation, compact laminate elements should be conditioned for an adequate period of time at the
installation location under the conditions of subsequent use. Compliance with the storage recommendations is also necessary on
construction sites.
2. PROCESSING
Due to the high density and resulting high cutting forces, the processing of compact laminate, compared to other wood-based
materials, leads to higher tool wear. The use of blunt or unsuitable tools can lead to inadequate machining and result in the
release of obnoxious odours. Tungsten carbide tools are mainly used. Diamond-tipped tools are recommended for processing
large quantities and automated processing centres. Ensure that the tool blades are maintained in good condition in order to obtain
satisfactory results. To ensure efficient and economical fabrication, especially prior to processing a large production batch or
implementing challenging projects, it is advisable to consult manufacturers on the most appropriate tool selection.
2.1. Extraction
Compliance with all safety standards and regulations, applicable to the wood processing industry in terms of dust extraction, fire
prevention etc., is essential when processing compact laminates. Where adequate extraction is not provided, respiratory protection
must be worn. The processing of compact laminates is not critical, however, a small number of people experience an allergic
reaction to any kind of dust.
EGGER Compact Laminate 43
plovitzahn hohle Zahnbrust
Duplovitzahn hohl
Dach-Duplovitzahn Flachzahn
2.2. Cutting
Panel or circular bench saws are recommended for cutting
compact laminates to size. A good cutting result depends on a
variety of factors, such as correct saw blade projection, feed rate,
tooth shape, tooth pitch, rotational and cutting speeds. Suitable
tooth shapes are alternate and hollow tooth, whilst the trapezoidal
flat tooth has proved to deliver longer tool life with consistently
Hollow
tooth
Duplovitzahn
mit
plovitzahn mit good
Fase cutting quality (see Figure
4). Trapez-Flachzahn Wechselzahn Trapezoidal flat toothDuplovitzahn
Alternate tooth
hohle Zahnbrust
Flachzahn
Figure 4
A very good cutting quality on both sides is achieved with the use of a scoring saw. The quality of the cut edge can be affected
by adjusting the height of the saw blade. A saw entry angle of 45° is optimal. This is achieved when 10 percent of the saw blade
diameter protrudes over the work piece.
• Cut on face side not clean → Set the saw blade higher
• Cut on the underside not clean → Set the saw blade lower
Alternatively, the cut on the underside can be improved by placing a base board of plywood, hardboard or similar underneath the
compact laminate sheet.
2.3. Machining Wechselzahn
Duplovitzahn mit Fase
Diamond-tipped tools are recommended for machining compact laminate. The suitability of carbide-tipped tools is limited.
Tools with segmented blades should not be used, as the overcut in the overlap zone usually remains visible. To ensure a good
edge quality, adding a processing allowance when cutting blanks is recommended, which, however, depends on subsequent
edge processing. Because of the high cutting pressure, secure work piece and tool control is of particular importance.
Numerous edge profiling options are available (see Figure 5).
Figure 5
Any cutter marks can be removed by sanding and an even edge colour can be achieved by applying a silicone-free oil. Sharp corners
and edges should be rounded to eliminate the risk of injury.
44 EGGER Compact Laminate
2.4. Drilling
Drill bits designed for plastic sheet materials, with a point angle between 60° and 80°, are the best choice for drilling compact
laminates (see Figure 6). The cutting speed and feed rate depend on the material of the chosen drill bit – HSS, HM, DIA. Please
observe the specifications of the tool manufacturer. Spiral bits for drilling metal or wood can also be used, but the rotation
speed and speed rate must be reduced in this case.
Source: Company LEUCO, Mosquito through-hole bit
Figure 6
For through holes, the compact laminate should be resting on a solid
base which can be drilled into. Before the drill bit breaks through,
the feed rate should be reduced in order to avoid break-outs on
the exit side. For drill holes that do not go through, so-called blind
holes, the minimum board thickness that must remain is 1.5mm.
For drill holes parallel to the board surface, the minimum board
thickness that must remain on either side of the drill hole is 3mm
(see Figure 7).
Figure 7
Cutting, milling, profiling and drilling tools should always be selected in consultation with the tool manufacturers.
3. FABRICATION
Despite the good dimensional stability of compact laminate, changes in the
ambient conditions can result in dimensional movement. The orientation of the
cellulose fibres in the sodium kraft paper used, gives the compact laminate a
production or machine direction (see Figure 8).
Dimensional movement along the length is approximately half as great as
it is across the width. The production direction of compact laminates with
a decorative finish on both sides can only be determined by the production
dimensions. It cannot be identified on compact laminate that has been cut
to size. Woodgrains and directionally printed decors constitute an exception.
Figure 8
When working with cut-size panels, it is important to ensure that the
production direction is always matched up during installation. In view of the
risk of confusion with cut-size panels, the production direction should be
marked on board remnants.
During fabrication and installation, the dimensional movement of the material must be taken into account from the outset.
As a general rule, an expansion allowance of 2.0 mm/m should be provided.
EGGER Compact Laminate 45
3.1. Cut-outs
Cut-outs and apertures, for example for switches, ventilator grills or access openings, always have to be rounded, since
sharp corners can lead to the formation of cracks (see Figure 9). Internal corners should be cut with an inner radius of at
least 3 mm. All edges must be smooth, free of cracks and notches. Grooves and rebates also have to be rounded in order to
avoid notch cracks. Cut-outs can be made directly with a router or pre-drilled with an appropriate radius and then sawn out
from drill hole to drill hole. Adequate expansion gaps must be allowed for integrated components.
Right!
Wrong!
Figure 9
3.2. Fixings
Through holes must have sufficient clearance to compensate for the dimensional movement resulting from temperature
and humidity fluctuations (see Figure 10). The diameter of the drill hole should be 2 – 3 mm larger than the diameter of
the fixing device in order to avoid cracking. Countersunk screws should not be used (see Figure 11). If countersunk screws
cannot be avoided, it is essential to use countersunk cup washers.
Right!
Wrong!
Figure 10
Figure 11
Cutting screw threads in compact laminate is straightforward and self-tapping screws can also be used without a problem.
Screws with a slow thread are recommended as they achieve a better pull-out resistance. Pre-drilling is essential in all
cases. Metal and chipboard screws are suitable for screw connections parallel to the board surface. Screws must penetrate
to a minimum depth of 25 mm and the diameter of the drill hole must be selected appropriately to prevent splitting.
46 EGGER Compact Laminate
3.3. Jointing
Joints between compact laminate elements, capable of withstanding higher stresses, can be achieved with a combination of
gluing and fixing devices, splines or biscuits (e.g. made of compact laminate), or grooves. Notes on bonding can be found
under point 3.4. Bonding. When joining compact laminates, care should be taken at all times to ensure that connecting
panels always follow the same production direction. Figures 12 to 16 below illustrate some possibilities for creating sturdy
compact laminate joints.
Grooved
Grooved/rebated
Splined
Figure 12
Figure 13
Figure 14
Angled spline
Metal profile, screw-fixed
Figure 15
Figure 16
3.4. Bonding
When bonding together two compact laminates, it is important to ensure that dimensional movements are not obstructed.
To avoid stress, only adequately conditioned compact laminates should be bonded together and always only in the same
machine direction. Bonding large surface areas should be avoided and the required application solutions and/or visual effects
should be realised by a partial build-up of the required section (see 5.5 False edge). Joints that are subjected to heavy stress,
for example due to vibrations, impacts or similar, should be reinforced with mechanical connecting elements. Examples
of possible corner designs can be found under 3.3 Jointing. Prior to bonding, the boards have to be prepared by sanding,
removal of dust, grease and contamination and pre-treated as necessary.
EGGER Compact Laminate 47
Suitable types of glue for bonding EGGER compact laminates include:
Glue type Jowat® 2K SE-Polymer 690.00
Glue type MBE Panel-loc
Glue type OTTOCOLL® P 85, OTTOCOLL® M500
Jowat AG
Ernst-Hilker-Straße 10 - 14
D-32758 Detmold
t +49 (0) 5231 749-0
info@jowat.de
www.jowat.de
Moderne Befestigungs Elemente GmbH
Siemensstr. 1
D-58706 Menden
Hermann Otto GmbH
Krankenhausstraße 14
D-83413 Fridolfing
t 0 86 84-908-0
info@otto-chemie.de
www.otto-chemie.de
t +49 (2373) 17430-0
info@mbe-gmbh.de
www.mbe-gmbh.de
Compact laminate can not only be partially bonded to compact laminate, but also to solid wood or wood-based materials such
as chipboard, MDF or multiplex board. For the concealed mounting of compact laminate elements to a substructure (see section
4.1 Wall panelling), we recommend, for example, Panel-loc by MBE. Conducting your own tests is recommended. Observing the
processing instructions of the glue manufacturers is essential.
3.5. False edge
Visually thicker boards can be achieved with built-up edges or by adding downturns or upstands. For built-up edges (Figure 17),
compact laminate strips as required are glued along the edge – once again, the same machine direction has to be observed. The
tension-equalising single-component Ottocoll® M500 adhesive by Otto Chemie is, for example, a suitable product.
Built-up edge
Downturn
Figure 17
Figure 18
For thicknesses up to 100 mm or if the decor has to be visible on the edge for aesthetic reasons, a downturn or upstand
(Figure 18) is a possible solution. First, the two components to be connected together are mitred at 45 degrees. Then the
work piece is placed on a level surface, face side down, so that the tips of the mitres are touching and adhesive tape is
applied over this joint. Then, both work pieces have to be turned over carefully. Now, glue is applied (Figure 19) and the
shorter work piece or upstand is then folded over and pressed home (Figure 20). The upstand has to be secured in the
correct position with adhesive tape until the glue has set. A suitable glue is, for example, OTTOCOLL® P 85.
Figure 19
Figure 20
48 EGGER Compact Laminate
4. APPLICATIONS
4.1. Wall panelling
Thanks to its robustness and suitability for everyday use, EGGER compact laminate is particularly well suited to interior wall
panelling applications. We recommend a minimum board thickness of 8 mm for such applications. The walls and substructure
should be completely dry prior to commencement of the panel installation. Always make provision for adequate air circulation
behind the panels. The material should not be exposed to trapped moisture. All panels to be joined together must follow the same
production direction.
4.1.1. Substructure and back ventilation
Compact laminate should be fixed to a sturdy, corrosion-resistant and interlocking substructure which securely supports the
weight of the wall panelling and ensures that ventilation behind the panels is provided. In drywall constructions, the fixings of
both, the substructure and the compact laminate always have to be anchored to the studwork frame (see Figure 21).
Concealed mounting
Detail Figure
21
1
3
6
7
2
5
3
5
4
1
2
3
4
5
6
Figure 21
7
Studwork frame
Insulation
Compact laminate strips
Two-layer gypsum fibreboard
Compact laminate
Adhesive
Panel fixing tape
The selection of the fixings has to be tailored to the substructure and the weight of the wall panelling. Different ambient conditions
in front and to the rear of the elements can lead to warping. It is therefore essential that compact laminate wall panelling
installations always make provision for adequate ventilation to the rear of the panels, which allows temperature and humidity to
equalise. The installation should be vented into the room. Vertical studs generally permit air circulation. Where substructures are
arranged horizontally, an appropriate construction must ensure that adequate ventilation is provided. The substructure should be
vertically plumb and horizontally level to allow stress free mounting of the entire panel surface. Suitable substructures are vertically
arranged strips of wood, aluminium or compact laminate (see also Figure 22).
EGGER Compact Laminate 49
Visible screw fixing
Detail Figure
22
1
1
2
2
1
2
Wooden battens
EPDM jointing tape
Figure 22
The maximum spacing of the battens and/or substructure depends on the chosen compact laminate thickness – see Figure 25. It is
important to ensure that air inlet and outlet areas remain unobstructed so that air circulation is not impeded. Also ensure that the
moisture of the surface to be panelled does not differ significantly from the moisture of the finished wall panel.
4.1.2. Visible mechanical fixings
When compact laminate is attached to the substructure using screws, sufficient allowance must be made for expansion. For this
purpose, floating points (see Figure 24) and one fixed point (see Figure 23) are drilled on the individual elements. The fixed point
serves to evenly distribute the expansion movement and should be positioned as centrally as possible (see Figure 25) – the drill
hole diameter is equal to the diameter of the fixing. The drill hole diameter of the floating points should be 2 – 3 mm larger than
the fixing. The drill hole should be covered by the screw head. Washers should be used if necessary. In the illustrations, an EPDM
sealing tape has been applied to the wooden substructure for protection against moisture.
1
1
1
Fixed point
Floating-point
Figure 23
Figure 24
EPDM jointing tape
50 EGGER Compact Laminate
The required expansion allowance is determined according to the longest distance from the fixed point to the edge of the board.
The floating point drill hole diameter must be increased by 2mm for every meter of length. For interior applications, the fixing
distances listed in the following table can be used:
Board thickness
[mm / inch]
Maximum fixing distances
a [mm]
b [mm]
6
615
400
8
790
500
10
920
670
12
960
900
13
970
920
EGGER compact laminates are self-supporting
from a thickness of ≥ 6mm.
= fixed point, × = floating point
Figure 25
4.1.3. Concealed mechanical fixings
The concealed fixing of compact laminates by suspension permits straightforward disassembly and is aesthetically more appealing
than visible screw connections. The removal of panels is quick and simple and cables and pipework installed behind the
elements are easily accessed. A further advantage is that, depending on the mounting system selected, elements can be adjusted
retrospectively. In addition, this method allows elements to be mounted stress-free. With all suspension fixing systems, sufficient
clearance must be allowed for raising and lowering the elements. This clearance or "suspension gap" will remain visible as a
shadow gap.
Batten suspension
For this mounting method, a groove is cut into the horizontal substructure to hold the rebated rail attached to the wall element. For
ease of fitting, the tongue of the rebated rail should be thinner than the groove. The rebated rails on the compact laminate elements
should not extend across the full width of the elements, they should be intermittent in order to permit vertical air circulation.
Rebated rails made of plywood or metal Z-profiles can be readily used. If a secure screw connection cannot be achieved with thin
compact laminate elements, additional gluing is possible.
Metal hardware suspension
Metal hardware systems are also available for mounting wall elements (see Figure 26). The chosen system must be used in
accordance with the recommendations of the manufacturer in order to ensure a secure installation.
EGGER Compact Laminate 51
Figure 26
4.1.4. Gluing
Compact laminate can also be mounted by gluing the panels to a rigid substructure, using permanently elastic adhesive systems
especially developed for this purpose. The systems consist of the glue, a panel fixing tape and appropriate pre-treatment products
for preparation of the surfaces. The purpose of the panel fixing tape is to initially secure the element until a permanent bond is
achieved with the glue (see Figure 27). Please observe the processing instructions of the glue manufacturer.
1
2
3
4
1
Adhesive
Compact laminate strips
Panel fixing tape
Compact laminate
2
3
4
Figure 27
Such glue systems are offered, for example, by the companies MBE, Innotec and DKS:
Moderne Befestigungs Elemente GmbH
Siemensstraße 1
D-58706 Menden
Innotec Österreich
Lofererstraße 83
A-6322 Kirchbichl
DKS Technik GmbH
Gnadenwald 90a
A-6069 Gnadenwald
t +49 (2373) 17430-0
info@mbe-gmbh.de
www.mbe-gmbh.de
t +43 (0)5332 70800
info@innotec.at
www.innotec.at
t +43 (0)5223 48488
office@dks.at
www.dks.at
52 EGGER Compact Laminate
4.1.5. Joints
Numerous options are available to create horizontal and vertical joints or seams (see Figure 28). However, it is important to ensure
that the elements have sufficient clearance for expansion.
Figure 28
4.2. Impact protection or partial wall panelling
An impact protection solution or partial wall panelling is required wherever walls are expected to be exposed to increased wear
and tear, for example in hospitals. In those locations, compact laminates are frequently used because they are robust and easy
to care for. In addition to half height wall panelling (see Figure 29) partial impact protection solutions are also common practice.
For partial impact protection solutions, compact laminate panels are usually fixed directly to the wall by means of visible screw
connections. As there is no ventilation to the rear of the elements, a vapour barrier has to be installed between the compact
laminate and the wall (see Figure 30).
Half height wall panelling - drywall (stud framing)
Glued solution
1
2
3
Wallpapered gypsum
plasterboard
2 Stainless steel bracket
3 Compact laminate
1
Figure 29
EGGER Compact Laminate 53
Solid wall with partial impact protection
Screw-fixed solution
1
2
1
2
Compact laminate
Vapour barrier
Figure 30
4.3. Sanitary and shower cubicles
When compact laminate is used in sanitary facilities, it is important to ensure during construction and installation that it is not
subjected to standing water and that adequate ventilation is provided in these rooms. It is imperative that only corrosion-free
construction materials and fixing devices are used. For application in wet areas it is essential to mechanically reinforce corner
connections by using dowels or splines, for example, and to employ a waterproofing adhesive system. For commercial applications
subjected to increased wear and tear, a minimum distance of 120mm must be maintained between the floor and lower edge of the
board (see Figure 31).
1
1
Figure 31
Spacing 120 mm
54 EGGER Compact Laminate
4.3.1. Glued compact laminate solutions
Compact laminates can also be used in non-commercial sanitary facilities, for
Detail 1, Figure 32, top edge finish
example in private households and/or hotels. It is important that adequate
ventilation is provided in these rooms and that the compact laminates can dry after
1
the shower has been used. Corrosion-free materials must be used for structures
and fixings. Absorbent mineral substrates such as walls, respectively plaster, have
3
to be primed with flexible waterproofing barriers. These barriers are generally
2
brushed on and prevent water from penetrating the substrate. The German
Construction Confederation offers a leaflet for such sealing and barrier products
("Waterproofing barriers for installations with tiles and boards"). This leaflet
describes liquid sealing compounds for use in conjunction with tiles and boards in
1
interior and exterior applications, taking into account defined moisture exposure
2
classes and substrates. The company Knauf, for example, offers such a sealant
3
Air gap
Adhesive
Panel fixing tape
called “Flächendicht”. The moisture exposure classes of the materials have to be
coordinated with the manufacturers or suppliers, and observing the processing
Detail 2, Figure 32, corner solution
instructions of the respective manufacturers is mandatory. The following are two
1
possible construction examples (see Figures 32 and 33).
2
3
Aluminium strips
4
5
5
Sealed substrate
Aluminium strip
3 Compriband (expanding sealing tape)
4 Silicone seal
5 Compact laminate
1
2
Detail 3, Figure 32, bottom edge finish
2
1
1
Figure 32 – Glued compact laminate solution 1
2
Compriband (expanding sealing tape)
Silicone seal
EGGER Compact Laminate 55
Compact laminate strips
Detail 1, Figure 33, top edge finish
1
3
2
1
2
3
Air gap
Adhesive
Panel fixing tape
Detail 2, Figure 33, bottom edge finish
1
4
3
2
1
2
3
4
Air gap
Tiled skirting
Silicone seal
Min. distance to floor 50 mm
Figure 33 – Glued compact laminate solution 2
Detail 3, Figure 33, corner solution
1
2
1
2
3
4
5
Sealed substrate
Compact laminate strips
Compriband (expanding sealing tape)
Silicone seal
Compact laminate
3
4
5
5
56 EGGER Compact Laminate
4.4. Hinged doors
Doors should not be wider than they are high. As dimensional movement along the length is only approximately half as great as
it is across the width, it is advisable to cut door leaves in the longitudinal direction of the compact laminate. Excessive differences
in temperature or relative humidity at the front and reverse sides of a door panel can cause the compact laminate to warp. For
this reason, it is imperative that adequate air circulation is provided for installations such as toilet cubicles or changing rooms
for example. The door width, height and weight are deciding factors for the number of hinges required. Other factors, such as
the installation location or whether additional stress is to be expected from the attachment of coats hooks, for example, can vary
greatly from case to case and must be taken into account.
The information provided (see Figure 34) should therefore be regarded as a guideline only for a door in 10mm thickness and a
width of up to 600mm. Performing a trial mounting is always recommended. For heavy duty applications, an additional hinge can
be fitted at max. 100mm below the upper hinge. The upper and lower hinges should be located at a minimum distance of 100mm
max., measured from the outer edge (X) of the panel. Suitable hinges are offered by the companies HÄFELE or Prämeta, for example
(see Figure 35).
Figure 34
Source: HÄFELE
Special hinge – Article 344.75.051
Figure 35
EGGER Compact Laminate 57
4.5. Table tops
Compact laminate is very suitable for table top applications, for example in offices, conference rooms, schools, and workshops.
The board thickness, fixing distances and the overhang over the frame must be configured in accordance with the loads to be
expected (see Figure 37). Table tops must have a minimum thickness of 10 mm so that sufficient material is available to ensure
secure screw connections. There are several fixing methods for attaching tops to frames or bases. The important factor is to ensure
that the assembly is stress-free. Screws can be driven directly into the board or a screw-in sleeve can be used. The fixing points in
the substructure must be implemented with sufficient clearance for expansion. The diameter of the drill hole should be 2 – 3 mm
larger than the diameter of the fixing device (see Figure 36).
Board
thickness
[mm]
Overhang
[mm]
Mounting
distance [mm]
10
170
310
12
240
390
13
270
440
Figure 36
Overhang
Mounting distance
Figure 37
58 EGGER Compact Laminate
4.6. Sink installation
Compact laminates are also popular for work surfaces in the kitchen, as well as for vanity units in toilet facilities.
In these fields of application, the installation of a sink or a washbasin is necessary. The following solutions
(see Figure 38 and 39) are generally implemented:
Figure 38, Solution 1
Figure 39, Solution 2
EGGER Compact Laminate 59
5. TECHNICAL DATA
Property
Standard
Resistance to surface wear
Resistance to impact by large diameter ball
EN 438-2:10
EN 438-2:21
Black core
Unit
Flammex
White core
CGS
ACS
CGF
ACF
BCS
Starting abrasion point
150
-
150
-
150
-
Abrasion value
350
-
350
-
350
-
*4
Number of revolutions (per minute)
Drop height in mm
2 mm ≤ t < 6 mm
1,400
800
1,400
800
-
-
6 mm ≤ t
1,800
800
1,800
800
-
-
≤ 10
≤ 12
≤ 10
≤ 12
-
-
Scratch resistance
EN 438-2:25
Rating
Diameter of the impression in mm
3
2
3
2
3
2
Resistance to staining group 1 and 2
EN 438-2:26
Rating
5
5
5
5
5
5
Resistance to staining group 3
EN 438-2:26
Rating
4
4
4
4
4
4
Light fastness (Xenon arc lamp, surface) *1
EN 438-2:27
Grey scale
4 to 5
4
4 to 5
4
4
4
-
-
-
-
3
3
Surface
4
-
4
-
4
-
Core
-
-
-
-
3 *3
3 *3
3
-
3
-
3
12
Surface
Core
Resistance to crazing
EN 438-2:24
Rating
Resistance to cigarette burns
EN 438-2:30
Rating
Flatness *2
EN 438-2:9
Depending on thickness in mm/m
Resistance to immersion in
boiling water
EN 438-2:12
2,0 mm ≤ t < 6,0 mm
8
8
8
8
12
6,0 mm ≤ t < 10,0 mm
5
5
5
5
8
8
10.0 mm ≤ t
3
3
3
3
5
5
Mass increase in %
2 mm ≤ t < 5 mm
5
5
-
-
5
5
t ≥ 5 mm
2
2
2
3
3
3
Thickness increase in %
2 mm ≤ t < 5 mm
6
6
-
-
6
6
t ≥ 5 mm
2
2
2
6
4
4
4
4
4
4
4
4
0.6
Appearance in degrees
Dimensional stability at elevated
EN 438-2:17
Cumulative dimension change in %
2 mm ≤ t < 5 mm
temperatures
t ≥ 5 mm
Resistance to dry heat
EN 438-2:16
Rating
La
0.4
0.4
-
-
0.6
Tb
0.8
0.8
-
-
1
1
La
0.3
0.3
0.3
0.3
0.5
0.5
Tb
0.6
0.6
0.6
0.6
0.8
0.8
4
-
4
-
4
3
Resistance to water vapour
EN 438-2:14
Rating
4
3
4
3
4
Resistance to wet heat (100 °C)
EN 12721:2009
Rating
4
-
4
-
-
-
Density
EN ISO 1183-1
g/cm³
≥ 1.35
≥ 1.35
≥ 1.35
≥ 1.35
≥ 1.4
≥ 1.4
Flexural modulus
EN ISO 178
MPa
9,000
9,000
9,000
9,000
9,000
9,000
Flexural strength
EN ISO 178
MPa
80
80
80
80
80
80
Tensile strength
EN IOS 527
MPa
60
-
60
-
60
-
Extraneous darkening and/or photochromism are due to the shock effect of accelerated exposure and are not characteristics of natural
exposure.
*2
The defined flatness values apply to compact laminate with decor on two sides. The limits for compact laminate with decor on one side
need to be agreed upon.
*1
*3
*4
t
a
b
Moderate cracks along the edges of the test specimen.
Compact laminates with a white core in combination with pearlescent decors are not defined by the Standard. This combination is,
however, possible and the values shown in the table under the pearlescent icon apply to this constellation.
t is the nominal thickness of the compact laminate.
L in longitudinal direction i.e. compact laminate length.
T in transverse direction i.e. compact laminate width.
60 EGGER Compact Laminate
6. CLEANING AND MAINTENANCE RECOMMENDATIONS
Because of its durable, hygienic and dense surface, EGGER compact laminate does not require special care. As a general rule,
stains and spilled substances such as tea, coffee and wine etc. should be cleaned up immediately, as the cleaning effort increases
if they are left to dry. When cleaning is necessary, mild agents should be used. Cleaning agents must in particular not contain any
abrasive components, as they may adversely affect the gloss level or scratch the surface.
The following recommendations should be observed in daily use:
Placing burning cigarettes on the compact laminate surface leads to surface damage.
Always use an ashtray.
Compact laminate surfaces should not be used as a cutting surface, as this can also leave cutting marks on highly
resistant compact laminate surfaces. Always use a chopping board.
Placing hot cooking utensils such as saucepans and frying pans directly from the hob or oven onto the compact
laminate surface should be avoided, as, depending on the heat exposure, a change in the gloss appearance or
damage to the surface can arise. Always use heat resistant mats.
Spilled liquids should always be cleaned up immediately, as prolonged exposure to some substances may cause a
change in the gloss level of compact laminate surfaces. Especially in the areas around cut-outs and joints, spilled
liquids should always be cleaned up quickly and thoroughly.
These recommendations apply especially to matt compact laminate surfaces. These have a distinctive look and feel, but have a
greater tendency to show wear and tear.
More detailed information can be found in our "EGGER laminate cleaning and maintenance instructions" leaflet at
www.egger.com/compactlaminate.
7. WASTE TREATMENT
Due to their very high calorific value, compact laminates are very suitable for thermal disposal in appropriate combustion plants.
Country specific waste management laws and regulations have to be observed at all times.
Provisional note:
This product brochure has been carefully drawn up to the best of our knowledge. We accept no liability for any mistakes, errors in standards or printing errors.
Furthermore, the continuous development of EGGER products might result in differences, as well as renewals of standards and documents of public law.
The content of this brochure is therefore not an instructions of use and not legally binding.
EGGER Compact Laminate 61
ZOOM IS SO MUCH MORE:
With Zoom we don’t just offer you high product quality and the latest trend orientated decors but also a wide range of helpful services: Your everyday resource.
JUST GIVE US A CALL. YOUR ZOOM HOTLINE
Sometimes you need an answer quickly. Our Zoom Hotline team will take
your sample order also on the phone, will be happy to answer your
technical questions and advise you in the selection of products and decors.
Just give us a call!
NEED TO VISUALISE YOUR IDEAS? USE VDS PROFI
With our Virtual Design Studio (VDS) software you can visualise your own ideas
and those of your customers with ease. Place EGGER decors into a wide variety of
available room sets or alternatively upload your own and view the chosen decors
in situ as furniture and on floors. Actively involve your customers in the room
design process and boost the success of your consultation: www.egger.com/vds
ALWAYS AT YOUR FINGERTIPS, EVEN ON THE MOVE. VDS ONLINE / VDS APP
With the free VDS ONLINE version and the VDS App you can view the EGGER Zoom and
flooring decors on all mobile devices. All decors can also be enlarged to full screen size.
In addition, there are 30 room sets available for individual visualisation.
www.egger.com/vdsonline
FOR EVERYTHING ELSE VISIT OUR WEBSITE
From technical data sheets, processing instructions and certificates to product
availability, distributor searches and the latest news it can all be found quickly
and efficiently at www.egger.com
All decors mentioned and shown are reproductions. Due to variables in the printing process, colours may
vary from the actual product.
62 EGGER Compact Laminate
AVAILABILITY GUIDE –
FULL PRODUCT OVERVIEW
Eurodekor
Melamine Faced
Chipboards
Laminates
ABS Edging
Pearlescent Decor
All dimensions in millimeter.
8; 16; 18;
19; 25
10; 12;
22; 28;
30; 32;
38
0.8
0.6
0.8
200 m
WHITE COLOURS
GFE
Painting Grade
W908
SM
Basic White
W908
ST2
Basic White
W911
SM
Cream White
*
W911
ST2
Cream White
*
W911
ST15
Cream White
*
W980
SM
Platinum White
W980
ST2
Platinum White
W980
ST15
Platinum White
W1000
ST2
Premium White
W1000
ST9
Premium White
W1000
ST18
Premium White
W1000
ST22
Premium White
W1000
ST26
Premium White
W1000
ST30
Premium White
W1000
A1
Premium White
W1000
ST88
Premium White
W1001
ST9
Solid Premium White
W1200
ST2
Porcelain
W1200
ST9
Porcelain
ST15
Alabaster
UNI COLOURS
U104
2014
*
75 m
54 × 2
42 × 2
42 × 0.8
31 × 2
23 × 2
23 × 0.8
22 × 0.4 (*23 × 0.4)
2,350 × 1,310
MED
2,150 × 1,020
2,150 × 950
Off the roll available
from 2,000 × 1,310
MED
3,050 × 1,310
Only for vertical use,
compact boards only one side pearlescent
2,800 × 1,310
2,800 × 2,070
E1 P2 CE
Further formats, thicknesses and core boards,
e.g. Eurospan E1 P3/MR CE, Eurospan JP
F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2),
Eurospan Flammex B/B1/M1, Eurospan E1
P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards,
EGGER OSB Combiline, upon request.
FLEX
Available
25 m
50 m
32
38
15
19
22
19 doubled
to 38
3; 4; 5;
6; 8; 10;
12; 13
5; 6; 8;
10; 12; 13
2,800 × 1,310
Classic
Finest
Compact
Laminates
2,800 × 2,070
Flammex black
core
Window Sills
2,790 × 2,060
MOD 801/6
4,100 × 160; 200;
250; 300; 400
(W980 also in 5,200
and 4,100 × 500)
Front Elements
Black core /
White core
MOD 800/6
4,100 × 160; 200;
250; 300; 400
(W980 also in
4,100 × 500)
MOD 200/3
two-sided
profile
2,800 × 160; 271;
296; 396; 446; 496;
546; 596
Laminate
Splashback
Panels
MOD 300/4
two-sided
profile
MOD 90
Length upon request
× 640
Eurospan
Worktops
2,800 × 680
MOD 300/3
two-sided
profile
Length upon request
× 920
MOD 300/3
one-sided
profile
with or without
hot melt
adhesive
Melamine
Edging
Length upon request
× 1,200
Length upon request
× 600
24 × 0.3
EGGER Compact Laminate 63
Eurolight
Lightweight
Boards
ProAcoustic
Acoustic Boards
38
50
20
64 EGGER Compact Laminate
Eurodekor
Melamine Faced
Chipboards
Laminates
ABS Edging
All dimensions in millimeter.
U107
ST9
Velvet Yellow
U108
ST15
Vanilla
U108
ST30
Vanilla
U113
ST15
Cotton
U114
ST15
Yellow
U129
ST15
Sun Yellow
U140
ST9
Saffron
U142
ST9
Lime
U143
ST15
Signal Yellow
U146
ST15
Maize Yellow
U147
ST15
Melon
U156
ST9
Sand Beige
U204
ST9
Camel
U206
ST9
Malaga
U216
ST15
Oyster
U222
ST15
Crema
U224
ST15
Silk
U311
ST15
Burgundy
U311
ST30
Burgundy
U317
ST9
Clay
U321
ST15
Red
U323
ST15
Chilli Red
U328
ST15
Lipstick
Pearlescent Decor
8; 16; 18;
19; 25
10; 12;
22; 28;
30; 32;
38
0.8
0.6
0.8
200 m
75 m
54 × 2
42 × 2
42 × 0.8
31 × 2
23 × 2
23 × 0.8
22 × 0.4 (*23 × 0.4)
2,350 × 1,310
MED
2,150 × 1,020
2,150 × 950
Off the roll available
from 2,000 × 1,310
MED
3,050 × 1,310
Only for vertical use,
compact boards only one side pearlescent
2,800 × 1,310
2,800 × 2,070
E1 P2 CE
Further formats, thicknesses and core boards,
e.g. Eurospan E1 P3/MR CE, Eurospan JP
F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2),
Eurospan Flammex B/B1/M1, Eurospan E1
P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards,
EGGER OSB Combiline, upon request.
FLEX
Available
25 m
50 m
32
38
15
19
22
19 doubled
to 38
3; 4; 5;
6; 8; 10;
12; 13
5; 6; 8;
10; 12; 13
2,800 × 1,310
Classic
Finest
Compact
Laminates
2,800 × 2,070
Flammex black
core
Window Sills
2,790 × 2,060
MOD 801/6
4,100 × 160; 200;
250; 300; 400
(W980 also in 5,200
and 4,100 × 500)
Front Elements
Black core /
White core
MOD 800/6
4,100 × 160; 200;
250; 300; 400
(W980 also in
4,100 × 500)
MOD 200/3
two-sided
profile
2,800 × 160; 271;
296; 396; 446; 496;
546; 596
Laminate
Splashback
Panels
MOD 300/4
two-sided
profile
MOD 90
Length upon request
× 640
Eurospan
Worktops
2,800 × 680
MOD 300/3
two-sided
profile
Length upon request
× 920
MOD 300/3
one-sided
profile
with or without
hot melt
adhesive
Melamine
Edging
Length upon request
× 1,200
Length upon request
× 600
24 × 0.3
EGGER Compact Laminate 65
Eurolight
Lightweight
Boards
ProAcoustic
Acoustic Boards
38
50
20
66 EGGER Compact Laminate
Eurodekor
Melamine Faced
Chipboards
Laminates
ABS Edging
Pearlescent Decor
All dimensions in millimeter.
U329
ST15
Tangerine
U330
ST9
Aubergine
U330
ST88
Aubergine
U332
ST15
Orange
U334
ST9
Powder
U336
ST9
Orchid
U337
ST9
Fuchsia
U337
ST88
Fuchsia
U343
ST9
Vino
U400
ST9
Violet
U506
ST15
Marine
U514
ST15
Baltic Blue
U518
ST9
Ice Blue
U522
ST15
Horizon
U525
ST15
Blue
U532
ST15
Petrol
U533
ST15
Polar Blue
U535
ST15
Aqua
U536
ST15
Lagoon
U537
ST15
Brilliant Blue
U537
A1
Brilliant Blue
U538
ST15
Ocean
U539
ST9
Steel Blue
2014
8; 16; 18;
19; 25
10; 12;
22; 28;
30; 32;
38
0.8
0.6
0.8
200 m
75 m
54 × 2
42 × 2
42 × 0.8
31 × 2
23 × 2
23 × 0.8
22 × 0.4 (*23 × 0.4)
2,350 × 1,310
MED
2,150 × 1,020
2,150 × 950
Off the roll available
from 2,000 × 1,310
MED
3,050 × 1,310
Only for vertical use,
compact boards only one side pearlescent
2,800 × 1,310
2,800 × 2,070
E1 P2 CE
Further formats, thicknesses and core boards,
e.g. Eurospan E1 P3/MR CE, Eurospan JP
F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2),
Eurospan Flammex B/B1/M1, Eurospan E1
P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards,
EGGER OSB Combiline, upon request.
FLEX
Available
25 m
50 m
32
38
15
19
22
19 doubled
to 38
3; 4; 5;
6; 8; 10;
12; 13
5; 6; 8;
10; 12; 13
2,800 × 1,310
Classic
Finest
Compact
Laminates
2,800 × 2,070
Flammex black
core
Window Sills
2,790 × 2,060
MOD 801/6
4,100 × 160; 200;
250; 300; 400
(W980 also in 5,200
and 4,100 × 500)
Front Elements
Black core /
White core
MOD 800/6
4,100 × 160; 200;
250; 300; 400
(W980 also in
4,100 × 500)
MOD 200/3
two-sided
profile
2,800 × 160; 271;
296; 396; 446; 496;
546; 596
Laminate
Splashback
Panels
MOD 300/4
two-sided
profile
MOD 90
Length upon request
× 640
Eurospan
Worktops
2,800 × 680
MOD 300/3
two-sided
profile
Length upon request
× 920
MOD 300/3
one-sided
profile
with or without
hot melt
adhesive
Melamine
Edging
Length upon request
× 1,200
Length upon request
× 600
24 × 0.3
EGGER Compact Laminate 67
Eurolight
Lightweight
Boards
ProAcoustic
Acoustic Boards
38
50
20
68 EGGER Compact Laminate
Eurodekor
Melamine Faced
Chipboards
Laminates
ABS Edging
Pearlescent Decor
All dimensions in millimeter.
U540
ST9
Denim
U608
ST9
Pistachio
U617
ST9
Wasabi
U625
ST15
Apple Green
U628
ST15
Green
U630
ST15
Lime Green
U630
A1
Lime Green
U631
ST9
Olive
U632
ST15
Grass Green
U633
ST15
Turquoise
U634
ST15
Velvet Green
U635
ST9
Moss
U701
ST9
Platinum
U702
ST9
Cashmere
U708
ST15
Light Grey
U727
ST9
Stone Grey
U727
ST22
Stone Grey
U727
ST26
Stone Grey
U730
ST9
Basalt
U732
ST15
Dust Grey
U741
ST9
Lava
U741
ST22
Lava
U748
ST9
Truffle
2014
2014
2014
8; 16; 18;
19; 25
10; 12;
22; 28;
30; 32;
38
0.8
0.6
0.8
200 m
75 m
54 × 2
42 × 2
42 × 0.8
31 × 2
23 × 2
23 × 0.8
22 × 0.4 (*23 × 0.4)
2,350 × 1,310
MED
2,150 × 1,020
2,150 × 950
Off the roll available
from 2,000 × 1,310
MED
3,050 × 1,310
Only for vertical use,
compact boards only one side pearlescent
2,800 × 1,310
2,800 × 2,070
E1 P2 CE
Further formats, thicknesses and core boards,
e.g. Eurospan E1 P3/MR CE, Eurospan JP
F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2),
Eurospan Flammex B/B1/M1, Eurospan E1
P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards,
EGGER OSB Combiline, upon request.
FLEX
Available
25 m
50 m
32
38
15
19
22
19 doubled
to 38
3; 4; 5;
6; 8; 10;
12; 13
5; 6; 8;
10; 12; 13
2,800 × 1,310
Classic
Finest
Compact
Laminates
2,800 × 2,070
Flammex black
core
Window Sills
2,790 × 2,060
MOD 801/6
4,100 × 160; 200;
250; 300; 400
(W980 also in 5,200
and 4,100 × 500)
Front Elements
Black core /
White core
MOD 800/6
4,100 × 160; 200;
250; 300; 400
(W980 also in
4,100 × 500)
MOD 200/3
two-sided
profile
2,800 × 160; 271;
296; 396; 446; 496;
546; 596
Laminate
Splashback
Panels
MOD 300/4
two-sided
profile
MOD 90
Length upon request
× 640
Eurospan
Worktops
2,800 × 680
MOD 300/3
two-sided
profile
Length upon request
× 920
MOD 300/3
one-sided
profile
with or without
hot melt
adhesive
Melamine
Edging
Length upon request
× 1,200
Length upon request
× 600
24 × 0.3
EGGER Compact Laminate 69
Eurolight
Lightweight
Boards
ProAcoustic
Acoustic Boards
38
50
20
70 EGGER Compact Laminate
Eurodekor
Melamine Faced
Chipboards
Laminates
ABS Edging
All dimensions in millimeter.
U750
ST9
Taupe Grey
U763
ST15
Pearl Grey
U763
ST18
Pearl Grey
U765
ST15
Silver Grey
U775
ST15
White Grey
U795
ST9
Brown Grey
U803
ST15
Black Brown
U807
ST9
Nougat
U808
ST9
Mocha
U961
ST2
Graphite
U961
ST15
Graphite
U961
ST30
Graphite
U963
ST15
Diamond Grey
U999
ST2
Black
U999
ST11
Black
U999
ST15
Black
U999
ST18
Black
U999
ST30
Black
WOOD REPRODUCTIONS
H045
ST15
Light Planked Timber
H047
ST15
Dark Plum Butcher-Block
H056
ST70
Core Maple
H078
ST79
Flowered Beech
Pearlescent Decor
8; 16; 18;
19; 25
10; 12;
22; 28;
30; 32;
38
0.8
0.6
0.8
200 m
75 m
54 × 2
42 × 2
42 × 0.8
31 × 2
23 × 2
23 × 0.8
22 × 0.4 (*23 × 0.4)
2,350 × 1,310
MED
2,150 × 1,020
2,150 × 950
Off the roll available
from 2,000 × 1,310
MED
3,050 × 1,310
Only for vertical use,
compact boards only one side pearlescent
2,800 × 1,310
2,800 × 2,070
E1 P2 CE
Further formats, thicknesses and core boards,
e.g. Eurospan E1 P3/MR CE, Eurospan JP
F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2),
Eurospan Flammex B/B1/M1, Eurospan E1
P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards,
EGGER OSB Combiline, upon request.
FLEX
Available
25 m
50 m
32
38
15
19
22
19 doubled
to 38
3; 4; 5;
6; 8; 10;
12; 13
5; 6; 8;
10; 12; 13
2,800 × 1,310
Classic
Finest
Compact
Laminates
2,800 × 2,070
Flammex black
core
Window Sills
2,790 × 2,060
MOD 801/6
4,100 × 160; 200;
250; 300; 400
(W980 also in 5,200
and 4,100 × 500)
Front Elements
Black core /
White core
MOD 800/6
4,100 × 160; 200;
250; 300; 400
(W980 also in
4,100 × 500)
MOD 200/3
two-sided
profile
2,800 × 160; 271;
296; 396; 446; 496;
546; 596
Laminate
Splashback
Panels
MOD 300/4
two-sided
profile
MOD 90
Length upon request
× 640
Eurospan
Worktops
2,800 × 680
MOD 300/3
two-sided
profile
Length upon request
× 920
MOD 300/3
one-sided
profile
with or without
hot melt
adhesive
Melamine
Edging
Length upon request
× 1,200
Length upon request
× 600
24 × 0.3
EGGER Compact Laminate 71
Eurolight
Lightweight
Boards
ProAcoustic
Acoustic Boards
38
50
20
72 EGGER Compact Laminate
Eurodekor
Melamine Faced
Chipboards
Laminates
ABS Edging
All dimensions in millimeter.
H087
ST79
Flowered Maple
H178
ST15
Afzelia Butcher-Block
H199
ST70
Wenge Butcher-Block
H806
ST9
Anthracite Oak Horizontal
H815
ST9
Cherry Horizontal
H834
ST9
Light Natural Oak Horizontal
H835
ST9
Light Oak Design
H836
ST15
Dark Oak Design
H850
ST9
Macassar Horizontal
H886
ST15
Beech Horizontal
H887
ST9
Maple Horizontal
H888
ST15
Walnut Horizontal
H1105
ST9
Aspen Beige
H1106
ST9
Aspen Grey
H1109
ST15
Dark Samoa
H1110
ST10
Splitwood
H1111
ST15
Snakewood
H1112
ST10
Zanzibar
H1129
ST15
Thermo Oak
H1133
ST9
Arlington Oak Horizontal
H1137
ST11
Black Brown Ferrara Oak
H1145
ST10
Natural Bardolino Oak
H1146
ST10
Grey Bardolino Oak
Pearlescent Decor
8; 16; 18;
19; 25
10; 12;
22; 28;
30; 32;
38
0.8
0.6
0.8
200 m
75 m
54 × 2
42 × 2
42 × 0.8
31 × 2
23 × 2
23 × 0.8
22 × 0.4 (*23 × 0.4)
2,350 × 1,310
MED
2,150 × 1,020
2,150 × 950
Off the roll available
from 2,000 × 1,310
MED
3,050 × 1,310
Only for vertical use,
compact boards only one side pearlescent
2,800 × 1,310
2,800 × 2,070
E1 P2 CE
Further formats, thicknesses and core boards,
e.g. Eurospan E1 P3/MR CE, Eurospan JP
F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2),
Eurospan Flammex B/B1/M1, Eurospan E1
P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards,
EGGER OSB Combiline, upon request.
FLEX
Available
25 m
50 m
32
38
15
19
22
19 doubled
to 38
3; 4; 5;
6; 8; 10;
12; 13
5; 6; 8;
10; 12; 13
2,800 × 1,310
Classic
Finest
Compact
Laminates
2,800 × 2,070
Flammex black
core
Window Sills
2,790 × 2,060
MOD 801/6
4,100 × 160; 200;
250; 300; 400
(W980 also in 5,200
and 4,100 × 500)
Front Elements
Black core /
White core
MOD 800/6
4,100 × 160; 200;
250; 300; 400
(W980 also in
4,100 × 500)
MOD 200/3
two-sided
profile
2,800 × 160; 271;
296; 396; 446; 496;
546; 596
Laminate
Splashback
Panels
MOD 300/4
two-sided
profile
MOD 90
Length upon request
× 640
Eurospan
Worktops
2,800 × 680
MOD 300/3
two-sided
profile
Length upon request
× 920
MOD 300/3
one-sided
profile
with or without
hot melt
adhesive
Melamine
Edging
Length upon request
× 1,200
Length upon request
× 600
24 × 0.3
EGGER Compact Laminate 73
Eurolight
Lightweight
Boards
ProAcoustic
Acoustic Boards
38
50
20
74 EGGER Compact Laminate
Eurodekor
Melamine Faced
Chipboards
Laminates
ABS Edging
Pearlescent Decor
All dimensions in millimeter.
H1150
ST10
Grey Authentic Oak
H1151
ST10
Brown Authentic Oak
H1189
ST10
Smoked Brown Bonanza Oak
H1215
ST22
Brown Cassino Ash
H1250
ST36
Navarra Ash
H1277
ST9
Light Lakeland Acacia
H1298
ST22
Sand Lyon Ash
H1334
ST9
Light Ferrara Oak
H1372
ST22
Natural Aragon Oak
H1377
ST36
Sand Orleans Oak
2014
H1379
ST36
Brown Orleans Oak
2014
H1424
ST22
Woodline Cream
H1428
ST22
Woodline Mocha
H1474
ST22
White Avola
H1476
ST22
Champagne Avola
H1484
ST22
Brown Grey Avola
H1486
ST36
Jackson Pine
H1487
ST22
Bramberg Pine
H1502
ST15
Alder
H1511
ST15
Bavarian Beech
H1518
ST15
Natural Beech
H1521
ST15
Maple
H1555
ST15
Wenge
2014
2014
8; 16; 18;
19; 25
10; 12;
22; 28;
30; 32;
38
0.8
0.6
0.8
200 m
75 m
54 × 2
42 × 2
42 × 0.8
31 × 2
23 × 2
23 × 0.8
22 × 0.4 (*23 × 0.4)
2,350 × 1,310
MED
2,150 × 1,020
2,150 × 950
Off the roll available
from 2,000 × 1,310
MED
3,050 × 1,310
Only for vertical use,
compact boards only one side pearlescent
2,800 × 1,310
2,800 × 2,070
E1 P2 CE
Further formats, thicknesses and core boards,
e.g. Eurospan E1 P3/MR CE, Eurospan JP
F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2),
Eurospan Flammex B/B1/M1, Eurospan E1
P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards,
EGGER OSB Combiline, upon request.
FLEX
Available
25 m
50 m
32
38
15
19
22
19 doubled
to 38
3; 4; 5;
6; 8; 10;
12; 13
5; 6; 8;
10; 12; 13
2,800 × 1,310
Classic
Finest
Compact
Laminates
2,800 × 2,070
Flammex black
core
Window Sills
2,790 × 2,060
MOD 801/6
4,100 × 160; 200;
250; 300; 400
(W980 also in 5,200
and 4,100 × 500)
Front Elements
Black core /
White core
MOD 800/6
4,100 × 160; 200;
250; 300; 400
(W980 also in
4,100 × 500)
MOD 200/3
two-sided
profile
2,800 × 160; 271;
296; 396; 446; 496;
546; 596
Laminate
Splashback
Panels
MOD 300/4
two-sided
profile
MOD 90
Length upon request
× 640
Eurospan
Worktops
2,800 × 680
MOD 300/3
two-sided
profile
Length upon request
× 920
MOD 300/3
one-sided
profile
with or without
hot melt
adhesive
Melamine
Edging
Length upon request
× 1,200
Length upon request
× 600
24 × 0.3
EGGER Compact Laminate 75
Eurolight
Lightweight
Boards
ProAcoustic
Acoustic Boards
38
50
20
76 EGGER Compact Laminate
Eurodekor
Melamine Faced
Chipboards
Laminates
ABS Edging
Pearlescent Decor
All dimensions in millimeter.
H1582
ST15
Ellmau Beech
H1599
ST15
Chocolate Tyrolean Beech
H1615
ST9
Romana Cherry
H1706
ST15
Cherry
H1733
ST9
Mainau Birch
H1793
ST9
Lava Tortona
2014
H1793
ST27
Lava Tortona
2014
H1796
ST9
Natural Tortona
2014
H1796
ST27
Natural Tortona
2014
H1867
ST9
Cream Canadian Maple
H1887
ST9
Natural Starnberg Maple
H1920
ST9
Natural Tyrolean Beech
H1950
ST15
Natural Calvados
H1951
ST15
Sienna Calvados
H1952
ST15
Amber Calvados
H2572
ST9
Woodstock
H3005
ST22
Grey Beige Zebrano
H3006
ST22
Sand Zebrano
H3012
ST22
Coco Bolo
H3025
ST15
Macassar
H3031
ST9
Dark Cordoba Olive
H3058
ST22
Mali Wenge
H3078
ST22
Hacienda White
8; 16; 18;
19; 25
10; 12;
22; 28;
30; 32;
38
0.8
0.6
0.8
200 m
75 m
54 × 2
42 × 2
42 × 0.8
31 × 2
23 × 2
23 × 0.8
22 × 0.4 (*23 × 0.4)
2,350 × 1,310
MED
2,150 × 1,020
2,150 × 950
Off the roll available
from 2,000 × 1,310
MED
3,050 × 1,310
Only for vertical use,
compact boards only one side pearlescent
2,800 × 1,310
2,800 × 2,070
E1 P2 CE
Further formats, thicknesses and core boards,
e.g. Eurospan E1 P3/MR CE, Eurospan JP
F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2),
Eurospan Flammex B/B1/M1, Eurospan E1
P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards,
EGGER OSB Combiline, upon request.
FLEX
Available
25 m
50 m
32
38
15
19
22
19 doubled
to 38
3; 4; 5;
6; 8; 10;
12; 13
5; 6; 8;
10; 12; 13
2,800 × 1,310
Classic
Finest
Compact
Laminates
2,800 × 2,070
Flammex black
core
Window Sills
2,790 × 2,060
MOD 801/6
4,100 × 160; 200;
250; 300; 400
(W980 also in 5,200
and 4,100 × 500)
Front Elements
Black core /
White core
MOD 800/6
4,100 × 160; 200;
250; 300; 400
(W980 also in
4,100 × 500)
MOD 200/3
two-sided
profile
2,800 × 160; 271;
296; 396; 446; 496;
546; 596
Laminate
Splashback
Panels
MOD 300/4
two-sided
profile
MOD 90
Length upon request
× 640
Eurospan
Worktops
2,800 × 680
MOD 300/3
two-sided
profile
Length upon request
× 920
MOD 300/3
one-sided
profile
with or without
hot melt
adhesive
Melamine
Edging
Length upon request
× 1,200
Length upon request
× 600
24 × 0.3
EGGER Compact Laminate 77
Eurolight
Lightweight
Boards
ProAcoustic
Acoustic Boards
38
50
20
78 EGGER Compact Laminate
Eurodekor
Melamine Faced
Chipboards
Laminates
ABS Edging
Pearlescent Decor
All dimensions in millimeter.
H3080
ST15
Sierra Mahogany
H3081
ST22
Hacienda Black
H3082
ST22
Amazonas
H3090
ST22
Driftwood
H3113
ST15
Lindau Pearwood
H3114
ST9
Tirano Pearwood
H3128
ST15
Natural Plum
H3129
ST9
Autumn Plum
H3303
ST10
Natural Arlington Oak
H3304
ST9
Grey Lacquered Chateau Oak
H3306
ST9
Anthracite Chateau Oak
H3309
ST9
Sand Gladstone Oak
2014
H3309
ST28
Sand Gladstone Oak
2014
H3325
ST9
Tobacco Gladstone Oak
2014
H3325
ST28
Tobacco Gladstone Oak
2014
H3326
ST9
Grey Beige Gladstone Oak
2014
H3326
ST28
Grey Beige Gladstone Oak
2014
H3331
ST10
Natural Nebraska Oak
H3332
ST10
Grey Nebraska Oak
H3344
ST36
Highline Oak
H3363
ST9
Anthracite Highland Oak
H3387
ST11
Rustic Oak
H3389
ST11
Natural Light Oak
2014
8; 16; 18;
19; 25
10; 12;
22; 28;
30; 32;
38
0.8
0.6
0.8
200 m
75 m
54 × 2
42 × 2
42 × 0.8
31 × 2
23 × 2
23 × 0.8
22 × 0.4 (*23 × 0.4)
2,350 × 1,310
MED
2,150 × 1,020
2,150 × 950
Off the roll available
from 2,000 × 1,310
MED
3,050 × 1,310
Only for vertical use,
compact boards only one side pearlescent
2,800 × 1,310
2,800 × 2,070
E1 P2 CE
Further formats, thicknesses and core boards,
e.g. Eurospan E1 P3/MR CE, Eurospan JP
F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2),
Eurospan Flammex B/B1/M1, Eurospan E1
P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards,
EGGER OSB Combiline, upon request.
FLEX
Available
25 m
50 m
32
38
15
19
22
19 doubled
to 38
3; 4; 5;
6; 8; 10;
12; 13
5; 6; 8;
10; 12; 13
2,800 × 1,310
Classic
Finest
Compact
Laminates
2,800 × 2,070
Flammex black
core
Window Sills
2,790 × 2,060
MOD 801/6
4,100 × 160; 200;
250; 300; 400
(W980 also in 5,200
and 4,100 × 500)
Front Elements
Black core /
White core
MOD 800/6
4,100 × 160; 200;
250; 300; 400
(W980 also in
4,100 × 500)
MOD 200/3
two-sided
profile
2,800 × 160; 271;
296; 396; 446; 496;
546; 596
Laminate
Splashback
Panels
MOD 300/4
two-sided
profile
MOD 90
Length upon request
× 640
Eurospan
Worktops
2,800 × 680
MOD 300/3
two-sided
profile
Length upon request
× 920
MOD 300/3
one-sided
profile
with or without
hot melt
adhesive
Melamine
Edging
Length upon request
× 1,200
Length upon request
× 600
24 × 0.3
EGGER Compact Laminate 79
Eurolight
Lightweight
Boards
ProAcoustic
Acoustic Boards
38
50
20
80 EGGER Compact Laminate
Eurodekor
Melamine Faced
Chipboards
Laminates
ABS Edging
Pearlescent Decor
All dimensions in millimeter.
H3400
ST22
Rustic Pine
H3420
ST36
Thermo Pine
H3660
ST9
Light Venetian Cherry
H3662
ST9
Natural Light Venetian Cherry
H3700
ST10
Natural Pacific Walnut
H3702
ST10
Tobacco Pacific Walnut
H3704
ST15
Tobacco Aida Walnut
H3734
ST9
Natural Dijon Walnut
H3739
ST15
Walnut Butcher-Block
H3753
ST22
Country Montana Larch
H3755
ST22
White Swiss Larch
H3758
ST9
Helsinki Birch
H3760
ST9
White Cape Elm
2014
H3760
ST29
White Cape Elm
2014
H3766
ST9
Dark Brown Cape Elm
2014
H3766
ST29
Dark Brown Cape Elm
2014
H3775
ST9
Light Tennessee Walnut
H3778
ST9
Natural Caribbean Walnut
H3840
ST9
Natural Mandal Maple
H3911
ST9
Natural Tauern Beech
F583
ST22
Fino Bronze
F584
ST22
Fino Cinnamon
F900
ST9
Artwood Light
2014
8; 16; 18;
19; 25
10; 12;
22; 28;
30; 32;
38
0.8
0.6
0.8
200 m
75 m
54 × 2
42 × 2
42 × 0.8
31 × 2
23 × 2
23 × 0.8
22 × 0.4 (*23 × 0.4)
2,350 × 1,310
MED
2,150 × 1,020
2,150 × 950
Off the roll available
from 2,000 × 1,310
MED
3,050 × 1,310
Only for vertical use,
compact boards only one side pearlescent
2,800 × 1,310
2,800 × 2,070
E1 P2 CE
Further formats, thicknesses and core boards,
e.g. Eurospan E1 P3/MR CE, Eurospan JP
F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2),
Eurospan Flammex B/B1/M1, Eurospan E1
P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards,
EGGER OSB Combiline, upon request.
FLEX
Available
25 m
50 m
32
38
15
19
22
19 doubled
to 38
3; 4; 5;
6; 8; 10;
12; 13
5; 6; 8;
10; 12; 13
2,800 × 1,310
Classic
Finest
Compact
Laminates
2,800 × 2,070
Flammex black
core
Window Sills
2,790 × 2,060
MOD 801/6
4,100 × 160; 200;
250; 300; 400
(W980 also in 5,200
and 4,100 × 500)
Front Elements
Black core /
White core
MOD 800/6
4,100 × 160; 200;
250; 300; 400
(W980 also in
4,100 × 500)
MOD 200/3
two-sided
profile
2,800 × 160; 271;
296; 396; 446; 496;
546; 596
Laminate
Splashback
Panels
MOD 300/4
two-sided
profile
MOD 90
Length upon request
× 640
Eurospan
Worktops
2,800 × 680
MOD 300/3
two-sided
profile
Length upon request
× 920
MOD 300/3
one-sided
profile
with or without
hot melt
adhesive
Melamine
Edging
Length upon request
× 1,200
Length upon request
× 600
24 × 0.3
EGGER Compact Laminate 81
Eurolight
Lightweight
Boards
ProAcoustic
Acoustic Boards
38
50
20
82 EGGER Compact Laminate
Eurodekor
Melamine Faced
Chipboards
Laminates
ABS Edging
All dimensions in millimeter.
F901
ST9
Artwood Brown
MATERIAL REPRODUCTIONS
F041
ST15
Sonora White
F042
ST70
Sonora Black
F043
ST70
Sonora Black Blue
F105
ST15
Torano Marble
F131
ST15
Trani Light Grey
F133
ST82
Trento Grey Beige
F145
ST2
Sardo Granite
F147
ST82
Valentino Grey
F148
ST82
Valentino Light Brown
F161
ST70
Artic Blue Grey
F166
ST9
Aurora Bianco
F202
ST15
Black Marble
F207
ST70
Portoro Black Brown
F210
ST9
White Grey Amalvi Marble
F211
ST9
Brown Amalvi Marble
F212
ST70
Lazio Grey Blue
F213
ST70
Lazio Anthracite
F214
ST10
Peacock Slate
F236
ST15
Terrano Grey
F238
ST15
Terrano Black
F274
ST9
Light Concrete
Pearlescent Decor
8; 16; 18;
19; 25
10; 12;
22; 28;
30; 32;
38
0.8
0.6
0.8
200 m
75 m
54 × 2
42 × 2
42 × 0.8
31 × 2
23 × 2
23 × 0.8
22 × 0.4 (*23 × 0.4)
2,350 × 1,310
MED
2,150 × 1,020
2,150 × 950
Off the roll available
from 2,000 × 1,310
MED
3,050 × 1,310
Only for vertical use,
compact boards only one side pearlescent
2,800 × 1,310
2,800 × 2,070
E1 P2 CE
Further formats, thicknesses and core boards,
e.g. Eurospan E1 P3/MR CE, Eurospan JP
F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2),
Eurospan Flammex B/B1/M1, Eurospan E1
P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards,
EGGER OSB Combiline, upon request.
FLEX
Available
25 m
50 m
32
38
15
19
22
19 doubled
to 38
3; 4; 5;
6; 8; 10;
12; 13
5; 6; 8;
10; 12; 13
2,800 × 1,310
Classic
Finest
Compact
Laminates
2,800 × 2,070
Flammex black
core
Window Sills
2,790 × 2,060
MOD 801/6
4,100 × 160; 200;
250; 300; 400
(W980 also in 5,200
and 4,100 × 500)
Front Elements
Black core /
White core
MOD 800/6
4,100 × 160; 200;
250; 300; 400
(W980 also in
4,100 × 500)
MOD 200/3
two-sided
profile
2,800 × 160; 271;
296; 396; 446; 496;
546; 596
Laminate
Splashback
Panels
MOD 300/4
two-sided
profile
MOD 90
Length upon request
× 640
Eurospan
Worktops
2,800 × 680
MOD 300/3
two-sided
profile
Length upon request
× 920
MOD 300/3
one-sided
profile
with or without
hot melt
adhesive
Melamine
Edging
Length upon request
× 1,200
Length upon request
× 600
24 × 0.3
EGGER Compact Laminate 83
Eurolight
Lightweight
Boards
ProAcoustic
Acoustic Boards
38
50
20
84 EGGER Compact Laminate
Eurodekor
Melamine Faced
Chipboards
Laminates
ABS Edging
Pearlescent Decor
All dimensions in millimeter.
F275
ST9
Dark Concrete
F276
ST9
Arkosa Sand
F277
ST9
Arkosa Grey
F292
ST9
Tivoli Beige
F310
ST87
Rust Ceramic
2014
F311
ST87
Anthracite Ceramic
2014
F371
ST82
Galizia Grey Beige
F381
ST10
Silk Fibre
F382
ST10
Titanium Fibre
F383
ST10
Bronze Fibre
F385
ST10
Cement
F390
ST82
Valetta Sand
F396
ST10
Basaltino Grey
F402
ST10
Vulcano Grey
F403
ST10
Vulcano Brown
F405
ST82
Galaxy White
F407
ST82
Galaxy Dark Brown
F425
ST10
Beige Linen
F426
ST10
Grey Linen
F427
ST10
Beige Leather
F428
ST10
Brown Leather
F437
ST2
Quartz Saffron
F438
ST2
Quartz Indigo
8; 16; 18;
19; 25
10; 12;
22; 28;
30; 32;
38
0.8
0.6
0.8
200 m
75 m
54 × 2
42 × 2
42 × 0.8
31 × 2
23 × 2
23 × 0.8
22 × 0.4 (*23 × 0.4)
2,350 × 1,310
MED
2,150 × 1,020
2,150 × 950
Off the roll available
from 2,000 × 1,310
MED
3,050 × 1,310
Only for vertical use,
compact boards only one side pearlescent
2,800 × 1,310
2,800 × 2,070
E1 P2 CE
Further formats, thicknesses and core boards,
e.g. Eurospan E1 P3/MR CE, Eurospan JP
F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2),
Eurospan Flammex B/B1/M1, Eurospan E1
P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards,
EGGER OSB Combiline, upon request.
FLEX
Available
25 m
50 m
32
38
15
19
22
19 doubled
to 38
3; 4; 5;
6; 8; 10;
12; 13
5; 6; 8;
10; 12; 13
2,800 × 1,310
Classic
Finest
Compact
Laminates
2,800 × 2,070
Flammex black
core
Window Sills
2,790 × 2,060
MOD 801/6
4,100 × 160; 200;
250; 300; 400
(W980 also in 5,200
and 4,100 × 500)
Front Elements
Black core /
White core
MOD 800/6
4,100 × 160; 200;
250; 300; 400
(W980 also in
4,100 × 500)
MOD 200/3
two-sided
profile
2,800 × 160; 271;
296; 396; 446; 496;
546; 596
Laminate
Splashback
Panels
MOD 300/4
two-sided
profile
MOD 90
Length upon request
× 640
Eurospan
Worktops
2,800 × 680
MOD 300/3
two-sided
profile
Length upon request
× 920
MOD 300/3
one-sided
profile
with or without
hot melt
adhesive
Melamine
Edging
Length upon request
× 1,200
Length upon request
× 600
24 × 0.3
EGGER Compact Laminate 85
Eurolight
Lightweight
Boards
ProAcoustic
Acoustic Boards
38
50
20
86 EGGER Compact Laminate
Eurodekor
Melamine Faced
Chipboards
Laminates
ABS Edging
All dimensions in millimeter.
F440
ST2
Quartz Bronze
F447
ST2
Quartz Lava
F488
ST2
Quartz Cubanit
F489
ST2
Quartz Inox
F495
ST2
Quartz Glass
F501
ST2
Titanium
F509
ST2
Aluminium
F598
ST2
Quartz Copper
F633
ST15
Grey Brown Metallo
F636
ST15
Titanium Blue Metallo
F784
ST2
Stainless Steel Microline
F870
ST10
Leon Slate
REAL ALUMINIUM LAMINATES
FA101
Brushed Aluminium
FA102
Brushed Steel Effect
DIGITAL PRINTING
D0014
ST15
Blue & Grey Pepita
D0015
ST15
Blue & Brown Pepita
D0016
ST15
Green & Grey Pepita
D0017
ST15
Lilac Variations
D0018
ST15
Beige Variations
D0020
ST15
Volcano Flames
D0021
ST15
Desert Flames
Pearlescent Decor
8; 16; 18;
19; 25
10; 12;
22; 28;
30; 32;
38
0.8
0.6
0.8
200 m
75 m
54 × 2
42 × 2
42 × 0.8
31 × 2
23 × 2
23 × 0.8
22 × 0.4 (*23 × 0.4)
2,350 × 1,310
MED
2,150 × 1,020
2,150 × 950
Off the roll available
from 2,000 × 1,310
MED
3,050 × 1,310
Only for vertical use,
compact boards only one side pearlescent
2,800 × 1,310
2,800 × 2,070
E1 P2 CE
Further formats, thicknesses and core boards,
e.g. Eurospan E1 P3/MR CE, Eurospan JP
F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2),
Eurospan Flammex B/B1/M1, Eurospan E1
P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards,
EGGER OSB Combiline, upon request.
FLEX
Available
25 m
50 m
32
38
15
19
22
19 doubled
to 38
3; 4; 5;
6; 8; 10;
12; 13
5; 6; 8;
10; 12; 13
2,800 × 1,310
Classic
Finest
Compact
Laminates
2,800 × 2,070
Flammex black
core
Window Sills
2,790 × 2,060
MOD 801/6
4,100 × 160; 200;
250; 300; 400
(W980 also in 5,200
and 4,100 × 500)
Front Elements
Black core /
White core
MOD 800/6
4,100 × 160; 200;
250; 300; 400
(W980 also in
4,100 × 500)
MOD 200/3
two-sided
profile
2,800 × 160; 271;
296; 396; 446; 496;
546; 596
Laminate
Splashback
Panels
MOD 300/4
two-sided
profile
MOD 90
Length upon request
× 640
Eurospan
Worktops
2,800 × 680
MOD 300/3
two-sided
profile
Length upon request
× 920
MOD 300/3
one-sided
profile
with or without
hot melt
adhesive
Melamine
Edging
Length upon request
× 1,200
Length upon request
× 600
24 × 0.3
EGGER Compact Laminate 87
Eurolight
Lightweight
Boards
ProAcoustic
Acoustic Boards
38
50
20
88 EGGER Compact Laminate
Eurodekor
Melamine Faced
Chipboards
Laminates
ABS Edging
All dimensions in millimeter.
D0022
ST15
Jungle Flames
D0023
ST15
Brown & Beige Flowers
D0024
ST15
Grey & Blue Flowers
D0025
ST15
Walnut Design
D0026
ST15
Metal Disk
Pearlescent Decor
8; 16; 18;
19; 25
10; 12;
22; 28;
30; 32;
38
0.8
0.6
0.8
200 m
75 m
54 × 2
42 × 2
42 × 0.8
31 × 2
23 × 2
23 × 0.8
22 × 0.4 (*23 × 0.4)
2,350 × 1,310
MED
2,150 × 1,020
2,150 × 950
Off the roll available
from 2,000 × 1,310
MED
3,050 × 1,310
Only for vertical use,
compact boards only one side pearlescent
2,800 × 1,310
2,800 × 2,070
E1 P2 CE
Further formats, thicknesses and core boards,
e.g. Eurospan E1 P3/MR CE, Eurospan JP
F0,3 (F****), Eurospan E1 EPF-S P2 CE (CARB 2),
Eurospan Flammex B/B1/M1, Eurospan E1
P5 CE, EGGER MDF-ST E1 CE, Eurolight Lightweight Boards,
EGGER OSB Combiline, upon request.
FLEX
Available
25 m
50 m
32
38
15
19
22
19 doubled
to 38
3; 4; 5;
6; 8; 10;
12; 13
5; 6; 8;
10; 12; 13
2,800 × 1,310
Classic
Finest
Compact
Laminates
2,800 × 2,070
Flammex black
core
Window Sills
2,790 × 2,060
MOD 801/6
4,100 × 160; 200;
250; 300; 400
(W980 also in 5,200
and 4,100 × 500)
Front Elements
Black core /
White core
MOD 800/6
4,100 × 160; 200;
250; 300; 400
(W980 also in
4,100 × 500)
MOD 200/3
two-sided
profile
2,800 × 160; 271;
296; 396; 446; 496;
546; 596
Laminate
Splashback
Panels
MOD 300/4
two-sided
profile
MOD 90
Length upon request
× 640
Eurospan
Worktops
2,800 × 680
MOD 300/3
two-sided
profile
Length upon request
× 920
MOD 300/3
one-sided
profile
with or without
hot melt
adhesive
Melamine
Edging
Length upon request
× 1,200
Length upon request
× 600
24 × 0.3
EGGER Compact Laminate 89
Eurolight
Lightweight
Boards
ProAcoustic
Acoustic Boards
38
50
20
Your everyday resource
Benefit from the comprehensive services of
EGGER and register now:
www.egger.com/myegger
EN-OS_04/2016
Technical modifications and printing errors excepted.
FRITZ EGGER GmbH & Co. OG
Holzwerkstoffe
Weiberndorf 20
6380 St. Johann in Tirol
Austria
t +43 50 600-0
f +43 50 600-10111
info-sjo@egger.com
奥地利爱格公司上海代表处地址
中国上海市南京西路580号南证大厦3609室
邮编200041
电话 +86 21 5234 0688
传真 +86 21 5234 0988
china@egger.com
Fritz Egger AG
1-9-5 Ginza, Chuo-ku, Tokyo-to
104-0061 Japan
t +81 3 6228 6470
f +81 3 6228 6471
m +81 90 8777 7719
japan@egger.com
EGGER Productos de Madera Limitada
San Francisco de Asís 150, Oficina 403
Vitacura, Santiago
Chile
ZIP code: 7650747
t +56 2 2243 8583
chile@egger.com
Arvind Katyal
B-5, Gulmohar Park
110049 New Delhi
India
t +91 11 32600929
f +91 11 46050305
india@egger.com
EGGER AUSTRALASIA PTY LIMITED
P.O. Box 697
Carlton South, Victoria
Australia, 3053
m +61 448 200 013
australia@egger.com