docwww.electrak.co.uk
download 
Report Transcription
www.electrak.co.uk
distributing power throughout the workplace www.electrak.co.uk totally flexible totally modular Intersoc is a complete modular desk power system, designed specifically to meet the increasing power and communication needs of the modern workplace. Its many unique design features enable rapid configuration and workstation relocation. Totally modular in design Modules simply push-fit and lock together All sockets are busbar interconnected, no terminals Conforms to BS7676: 2001 Section 607 High Protective Conductor Currents Complete range of under and on desk configurations Standard 2P+E and clean earth 2P+E+CE Intersoc modules have been designed with speed of installation and flexibility in mind. They can be factory configured or assembled on site and the modularity of the Intersoc system enables you to expand units easily and safely when demanded. For example, when additional sockets are required, the modules can simply be disconnected and a new module can be added, push-fitted and locked together. In-feed modules can be safely connected to the power supply prior to workstation installation, allowing circuits to be electrically tested, signed off and carpets fitted. And with simple 'through' screw holes in the feed units and end caps of the under desk modules and desk clamps for the on desk units, Intersoc can be easily installed onto all types of fixing surface. Due to its modular design, Intersoc can be configured to create thousands of combinations to suit any application. Contact the Electrak sales office for a quotation that meets your desk power requirements: Telephone 01207 503400 or email sales@electrak.co.uk module interconnection module end view Push together to self lock Shuttered module inter connection 2 To disconnect slide green clip, and pull apart system connection 4 socket in-feed module, 2 socket module and blank end cap. Mains connection BS1363 plug, lead and GST connector. Under desk and on desk interconnected. In-feed, RCD protection module 2 x 4 socket modules and blank end cap. Commando socket or equivalent. International socket outlet range for under or on top of desks UK Cyprus, Hong Kong, Ireland, Kuwait, Malaysia, Oman, Qatar, Singapore, UAE, UK 15A Round Pin India, South Africa, Sri Lanka 5A Round Pin India, Sri Lanka Schuko Austria, Finland, Germany, Greece, Holland, Hungary, Iceland, Latvia, Luxembourg, Norway, Poland, Portugal Romania, Russia, Sweden, Turkey North America USA, Brazil, Canada, Philippines, Saudi Arabia, Thailand Euro Austria, Belgium, Bulgaria, Czech, Egypt, France, Greece, Iceland, Italy, Latvia, Luxembourg, Norway, Poland, Portugal, Romania, Slovakia, Spain, Sweden, Syria, Turkey Chinese and Australian Argentina, Australia, China 3 range options Mains connection Rewirable BS1363 plug GST18 or ST18 connectors Neutrik connector Interlink connectors Rewirable GST18 or ST18 connectors Neutrik connector Intersoc pre-wired Protection & switching Switch with neon Neon BS1362 fuse 3, 5, 7 & 13A MCB RCD Fused sockets 3.15A or 5A to BS6396 Interconnection leads Female to male GST or ST connectors and lead Intersoc female to male connectors and lead Other combinations to customer requirements Bespoke range Electrak will supply any bespoke combination to customers requirements from the wide range of modules and accessories available. Contact sales on 01207 503400 or email sales@electrak.co.uk 16A popular range Electrak have created an off-the-shelf range based around the 2 and 4 socket in-feed module. Mains connection to these modules will be via an integral GST 18/3 connector or rewirable terminals. The In-feed module can be used as stand alone by adding a blank end cap (TT542137) to cover the open end - or - extra 2 or 4 socket modules can be added directly to the in-feed module to increase the number of sockets to application requirement. 2 socket in-feed module If the module requires to be linked to other modules via flexible cable, instead of using an end cap, an interlink connector either GST18/3 type or rewirable is push fitted into the open end of the module, allowing for interconnection via link leads. The last module in any run or combination should have a blank end cap to cover the open end. Blank end cap 4 socket in-feed module GST Interconnect male Rewirable Interconnect male 60mm 290mm 410mm 2 socket module 50mm 22mm GST Interconnect female 4 socket module 65mm Rewirable Interconnect female End view 60mm 34mm 60mm 155mm 275mm 75mm 110mm Rewirable infeed has 16mmØ hole for flexible cable entry cable restraint. Socket outlet orientation Socket outlets can be supplied with various outlet orientation combinations 45˚ 4 90˚ 135˚ Unfused Fused 3.15A or 5A IEC fuses popular under-desk combinations Examples of some popular under-desk configurations: NB: Using 2 & 4 gang socket in-feeds code description 2 Socket In-feed Modules with GSTi3 Male Feed Connector and Open End TT751160 TT310744 16A 2 Socket Module 45º Socket Orientation 16A 2 Socket Module 90º Socket Orientation TT327075 TT777229 16A 2 Socket Switched Neon Module 45º Socket Orientation 16A 2 Socket Switched Neon Module 90º Socket Orientation TT870046 TT844274 16A 2 Socket Fused and Switched Neon Module 45º Socket Orientation 16A 2 Socket Fused and Switched Neon Module 90º Socket Orientation 4 Socket In-feed Modules with GSTi3 Male Feed Connector and Open End TT635272 TT502794 16A 4 Socket Module 45º Socket Orientation 16A 4 Socket Module 90º Socket Orientation TT402032 TT294343 16A 4 Socket Switched Neon Module 45º Socket Orientation 16A 4 Socket Switched Neon Module 90º Socket Orientation TT294298 TT566130 16A 4 Socket Fused and Switched Neon Module 45º Socket Orientation 16A 4 Socket Fused and Switched Neon Module 90º Socket Orientation 2 Socket In-feed Modules with Rewirable Feed and Open End TT809575 TT194787 16A 2 Socket Rewirable Module 45º Socket Orientation 16A 2 Socket Rewirable Module 90º Socket Orientation TT462789 TT786788 16A 2 Socket Rewirable, Switched Neon Module 45º Socket Orientation 16A 2 Socket Rewirable, Switched Neon Module 90º Socket Orientation TT430173 TT548771 16A 2 Socket Rewirable, Fused and Switched Neon Module 45º Socket Orientation 16A 2 Socket Rewirable, Fused and Switched Neon Module 90º Socket Orientation 4 Socket In-feed Modules with Rewirable Feed and Open End TT597866 TT831882 16A 4 Socket Rewirable Module 45º Socket Orientation 16A 4 Socket Rewirable Module 90º Socket Orientation TT343184 TT869233 16A 4 Socket Rewirable, Switched Neon Module 45º Socket Orientation 16A 4 Socket Rewirable, Switched Neon Module 90º Socket Orientation TT760714 TT552721 16A 4 Socket Rewirable, Fused and Switched Neon Module 45º Socket Orientation 16A 4 Socket Rewirable, Fused and Switched Neon Module 90º Socket Orientation 2 Socket In-feed Modules BS6396 Fused Sockets with GSTi3 Male Feed Connector and Open End TT665242 TT521162 16A 2 Socket Module, Sockets 3.15A Individually Fused 45º Socket Orientation 16A 2 Socket Module, Sockets 3.15A Individually Fused 90º Socket Orientation TT415868 TT127635 16A 2 Socket Switched Neon Module, Sockets 3.15A Individually Fused 45º Socket Orientation 16A 2 Socket Switched Neon Module, Sockets 3.15A Individually Fused 90º Socket Orientation 5 popular under-desk combinations cont. code description 4 Socket In-feed Modules BS6396 Fused Sockets with GSTi3 Male Feed Connector and Open End TT541066 TT672822 16A 4 Socket Module, Sockets 3.15A Individually Fused 45º Socket Orientation 16A 4 Socket Module, Sockets 3.15A Individually Fused 90º Socket Orientation TT569853 TT386356 16A 4 Socket Switched Neon Module, Sockets 3.15A Individually Fused 45º Socket Orientation 16A 4 Socket Switched Neon Module, Sockets 3.15A Individually Fused 90º Socket Orientation Add on options Additional socket modules code description 2 Socket Modules TT155722 TT449140 TT157710 2 Socket Module 45º Socket Orientation 2 Socket Module 135º Socket Orientation 2 Socket Module 90º Socket Orientation 4 Socket Modules TT615552 TT441402 TT715742 4 Socket Module 45º Socket Orientation 4 Socket Module 135º Socket Orientation 4 Socket Module 90º Socket Orientation 2 Socket Modules TT858492 TT651543 TT368427 2 Socket Module with 3.15A Individually Fused Sockets 45º Socket Orientation 2 Socket Module with 3.15A Individually Fused Sockets 135º Socket Orientation 2 Socket Module with 3.15A Individually Fused Sockets 90º Socket Orientation 4 Socket Modules TT214432 TT713717 TT491992 4 Socket Module with 3.15A Individually Fused Sockets 45º Socket Orientation 4 Socket Module with 3.15A Individually Fused Sockets 135º Socket Orientation 4 Socket Module with 3.15A Individually Fused Sockets 90º Socket Orientation Closing Module End or Interconnection to another Socket Module TT542137 TT700539 TT270782 TT725122 TT192210 Blank End Cap Male Interconnect with Female GSTi3 Connector Power Out Female Interconnect with Male GSTi3 Connector Power In Male Interconnect Rewirable Power Out 16A Rewirable Feed Module Interconnection Between Modules Using GSTi3 Connectors & Leads TT245952 TT513313 TT260603 TT184829 TT261742 0.3m 16A Male to Female GSTi3 Connectors c/w 1.5mm2 Cable 0.5m 16A Male to Female GSTi3 Connectors c/w 1.5mm2 Cable 1m 16A Male to Female GSTi3 Connectors c/w 1.5mm2 Cable 2m 16A Male to Female GSTi3 Connectors c/w 1.5mm2 Cable 3m 16A Male to Female GSTi3 Connectors c/w 1.5mm2 Cable Mains Power Leads TT120201 TT341457 TT789663 2m 13A Fused BS1363 Plug to Female GSTi3 Connector c/w 1.5mm2 Cable 3m 13A Fused BS1363 Plug to Female GSTi3 Connector c/w 1.5mm2 Cable 5m 13A Fused BS1363 Plug to Female GSTi3 Connector c/w 1.5mm2 Cable Mains power lead Interlink GST connectors & flexible lead 4 socket in-feed module Female GST interlink connector 6 4 socket module Male GST interlink connector Blank end cap popular under-desk combinations desktop range The range features two unit types - vertically mounted, or mounted flat onto the desk. Mounted vertically on the desk top Mounted horizontal on the desk top Intersoc desktop modules offer all you will ever need in a sleek aluminium finish. With a range of mounting options to compliment your furniture arrangements, it is the quality finish you were looking for, at a highly competitive price. Any combination of socket outlets and other services can be integrated into the aluminium housing to suit customer requirements, contact sales: Telephone 01207 503400 or email sales@electrak.co.uk 7 Vertical module on desk unit Horizontal module on desk unit Electrak will manufacture any combination of socket and service outlets to customer requirements such as USB ports, BNC, IBM, Co Axial, SVGA, RJ45 etc. Contact sales: Telephone 8 01207 503400 or email sales@electrak.co.uk popular on desk combinations 16A Vertical On Desk Modules code description PP426707 Vertical Desktop Unit 2 sockets 45º 3.15A Individually Fused PP861258 Vertical Desktop Unit 2 sockets 45º 3.15A Fused +2 x RJ45 Cat 5e Data Outlets PP598708 Vertical Desktop Unit 4 sockets 45º 3.15A Individually Fused PP584320 Vertical Desktop Unit 4 sockets 45º 3.15A Fused +2 x RJ45 Cat 5e Data Outlets PP362767 Vertical Desktop Unit 2 sockets 45º 5A Individually Fused PP800101 Vertical Desktop Unit 2 sockets 45º 5A Individually Fused +2 x RJ45 PP815834 Vertical Desktop Unit 4 sockets 45º 5A Individually Fused PP398205 Vertical Desktop Unit 4 sockets 45º 5A Individually Fused +2 x RJ45 Cat 5e Data Outlets Cat 5e Data Outlets All units supplied as standard with 1m Power Lead & Male GST Connector RJ45 (Cat 5e) c/w 3m Data Lead (Supplied as Standard) Desktop units require mains connection via Female GST Connector 16A Horizontal On Desk Modules code description PP409388 Horizontal Desktop Unit 2 sockets 90º 3.15A Individually Fused PP191446 Horizontal Desktop Unit 2 sockets 90º 3.15A Fused +2 x RJ45 PP340880 Horizontal Desktop Unit 4 sockets 90º 3.15A Individually Fused PP524786 Horizontal Desktop Unit 4 sockets 90º 3.15A Fused +2 x RJ45 Cat 5e Data Outlets Cat 5e Data Outlets PP705425 Horizontal Desktop Unit 2 sockets 90º 5A Individually Fused PP659337 Horizontal Desktop Unit 2 sockets 90º 5A Individually Fused +2 x RJ45 Cat 5e Data Outlets PP624626 Horizontal Desktop Unit 4 sockets 90º 5A Individually Fused PP530426 Horizontal Desktop Unit 4 sockets 90º 5A Individually Fused +2 x RJ45 Cat 5e Data Outlets All units supplied as standard with 1m Power Lead & Male GST Connector 3m Telecom Lead c/w RJ45 & 3m Data Lead c/w RJ45 (Supplied as Standard) Desktop units require mains connection via Female GST Connector Fixing code description PP119335 PP852827 PP792855 Horizontal Desktop Unit Fixing Clamp - 2 per pack Vertical Desktop Unit Fixing Clamp - 2 per pack Desktop Adhesive Strip Please use one bracket pack per desk unit or adhesive strip for horizontal desk units only 9 desktop modules technical information Testing and Accreditation British Standards Conforms to BS5733 and the relevant parts of BS1363 part 2 Manufacturing approved to ISO9001: 2000 Quality Assurance Certificate No. 10270 BS6396: 2002 Electrical Systems in Office Furniture and Office Screens Electrical Test Data Rated Current Rated Voltage Frequency 16A 250V ~ 50/60Hz Conductor Resistance at 20°C 2 Socket Module 4 Socket Module 1.4mΩΩ 2.8mΩΩ Volt Drop Live & Neutral 2 Socket Module 4 Socket Module Protection Module 2.8mΩ 5.6mΩ 4.0mΩ (Depending on Device) In-feeds: 16A +1.5mm2 +4mm2 Interconnections: 16A +1.5mm2 +4mm2 Earth Fault Loop Impedance 2 Socket Module 4 Socket Module Protection Module 2.0mV/A 29mV/Am 11mV/Am 2.0mV/A 29mV/Am 11mV/Am 2.8mΩ 5.6mΩ 4.0mΩ (Depending on Device) In-feeds: 16A +1.5mm2 +4mm2 Interconnections: 16A +1.5mm2 +4mm2 2.0mΩ 29mΩ/m 11mΩ/m 2.0mΩ 29mΩ/m 11mΩ/m Mechanical Data Number of conductors 3 Busbar conductor cross sectional area 5mm2 16A Rewirable In-feed terminal capacity 10mm2 Material Specification Under Desk: Module Housing Socket Outlets Busbars Other Metalwork On Desk: Module Housing Module Fascia Socket Outlets 10 VØ Flame Retardant ABS Polycarbonate High Conductivity Copper C101 Phosphor Bronze PB102, PB103, Brass CZ108, High Conductivity Copper C101 Aluminium VØ Flame Retardant ABS Polycarbonate BS7671: 2008 Requirements for Electrical Installation (IEE Wiring Regulations 17th Edition) Electricity at Work Regulations 1989 Health & Safety Legislation Below is a brief outline of the main criteria within the standards: BS6396: 2002 was published with regard to the use of electrical equipment within general office furniture and screens. This standard sets out in its scope the use and testing of electrical socket outlets and associated wiring when used together with a 13A BS1363 fused plug and makes provision for the routing of cables through furniture. For compliance with this standard socket outlet configurations 2 or 4 outlets should be individually fused at 5A and 6 outlets individually fused at 3.15A. A note on individual socket fusing – BS6396 Compliance: The standard requires individual socket fusing (please see table below). Electrak’s standard range uses 3.15A individual fusing to future-proof for expansion. However, 5A fusing is also available as an alternative. Total Number of Sockets Individually Fused at 2 or 4 Sockets 6 Sockets 5A 3.15A BS7671: 2008 (17th Edition). The Health and Safety Executive states that installations which conform to the standards laid down in BS7671: 2008 are regarded by the HSE as likely to achieve conformity with the relevant parts of the Electricity at Work Regulations 1989. Special note should be taken of regulation 543.7 within BS7671: 2008 - Earthing requirements for the installation of equipment having high protective conductor currents. Regulation 543.7 has particular importance when there is a requirement for a quantity of information technology equipment being supplied from a final circuit in a location where the sum of their protective currents exceeds 10mA in normal use. Due to current in the protective conductor arising from the use of IT equipment, there is a requirement to provide mechanically protected 4mm2 conductor (543.7.1.3(ii)). Intersoc achieves this when wired in accordance with the installation sheets by providing mechanically protected 5mm2 earth conductors within the product. Electrak International Limited - conditions of quotation and AND supply ELECTRAK INTERNATIONAL LIMITED - CONDITIONS OF QUOTATION SUPPLY 1.. Interpretation n In these conditions:a) “Company” means Electrak International Limited registered in the United Kingdom under number 1248359; b) “Conditions” means the standard conditions of (quotation and) supply set out in this document and (unless the context otherwise requires) includes any special conditions agreed in writing between the Company and the Purchaser; c) “Contract” means the contract for the purchase and sale of the Goods and/or the Services; d) “Goods” means any product sold or system designed and sold by the Company specified in the accepted quotation or order (as the case may be) (including any part or parts thereof) and any other goods which the Company is to supply in accordance with these Conditions; e) “Intellectual Property Rights” means all copyright, design rights (registered or unregistered), patents, trade marks and any other rights in the nature of intellectual property rights; f) “Purchaser” means the person firm or company who requests a quotation from the Company for the sale of the Goods and/or Services or who places an order with the Company for the purchase of the Goods and whose order for the Goods is accepted by the Company or who requests the Company to carry out the Services; g) “Services” means all construction, installation, maintenance, commissioning and other services which the Company agrees to perform for the Purchaser in connection with the Contract; and h) “Writing” includes telex, cable, facsimile transmission and comparable means of communication. 2.. Quotation n and d Orderr Upon request in writing from the Purchaser the Company shall supply a written quotation for the sale and supply of the Goods and/or the Services. The Contract is formed by the Company’s acceptance of the Purchaser’s offer in response to the Company’s quotation or by the Company’s acceptance of the Purchaser’s order for the Goods or request to carry out the Services. 3.. Formation n off Contractss a) All contracts of quotation and supply made with the Company shall be deemed to incorporate these Conditions which shall override and take precedence over any other terms or conditions in any document or other communication used by the Purchaser in concluding this or any other contract with the Company. No variation of or addition to these Conditions shall form part of any contract unless made or specifically accepted by an authorised officer of the Company in writing. b) The application of the Uniform Laws on International Sales shall be excluded. The construction validity and performance of all Contracts shall be governed by the laws of England and any claim or dispute arising therefrom shall be subject to the exclusive jurisdiction of and be determined by the English Courts. 4.. Pricess Unless otherwise expressly stated in writing by the Company orders are accepted on the basis that:a) the price stated is the net price of the Goods and/or the Services for delivery in accordance with the Contract; b) the price stated is exclusive of Value Added Tax which will be charged at the rate and in the manner prescribed by law; c) the Company is entitled without prior notice to adjust the price stated to take account of any change in specification made at the request of the purchaser or any alteration before the date of delivery or performance in the cost to the Company of labour, materials, sub-contracted services or import or export duties or tariffs or transport or any other matter beyond the control of the Company which results in an increase in costs to the Company; d) unless otherwise expressly stated in writing by the Company, the Company will charge for carriage, insurance during carriage and packing and where such charges are stated separately from the price they will nevertheless be payable by the Purchaser at the same time as if they formed part of the price and shall be treated as such. 5.. Paymentt a) Unless otherwise expressly stated in writing by the Company prices are due and payable in United Kingdom sterling within 30 days of the date of the invoice. b) Payment shall be made without deduction or set-off. c) If the Purchaser shall fail to make payment in full in accordance with Condition 5(a) above, then (without prejudice to any other rights of the Company) the Purchaser shall without any need for the Company to give notice become liable to pay to the Company interest on the amount for the time being unpaid at the rate which is eight percent per annum above the UK Clearing Bank Base Lending Rate calculated from the date of due payment until the date of actual payment whether before or after any judgement; and:i. the Company shall be entitled to suspend all or any deliveries and/or performance to be made under this or any other contract with the Purchaser and all monies under this or any other contract then outstanding shall immediately become due and payable and the Purchaser shall not in any respect be released from its obligations to the Company under this or any such other contract; or ii. instead of suspension in accordance with subparagraph (c)(i) above, the Company shall be entitled to terminate this Contract and/or any other contract with the Purchaser in accordance with Condition 18 below and to claim damages from the Purchaser for breach; and iii. without prejudice to any other remedies as detailed in subparagraphs (c)(i) and ii above, the Company may in addition set off any sums it owes to the Purchaser on any other contract it has with the Purchaser whether such sums are liquidated or unliquidated as at the date of the Purchaser’s breach of these Conditions. d) Time of payment is of the essence of the Contract. 6.. Cancellation n a) If the Purchaser cancels the order, whether in writing or orally, prior to completion of delivery of the Goods; i. the Company may treat the Contract as terminated forthwith in which event the Company may, in its absolute discretion, have recourse to any rights and remedies available under Condition 18; and ii. the Company shall be entitled to sell the Goods or the balance of the Goods still in its possession and to seek to obtain the best reasonable price for such Goods and to retain any such recovery made. b) If cancellation or return of the Goods is not due to any loss or damage or any fault of the Company, the Company may levy a handling charge of at least 25% of the value of the returned Goods to cover costs of restocking, transport and administration. In any event, Goods that are specialised or modified in any way are not eligible for return or credit. c) Insofar as the Company has been unable to sell the Goods or to the extent that it has been unable to sell the balance of the Goods, the Company shall submit written details of the costs of purchase and/or manufacture of the Goods to the Purchaser, including details of any recovery made by way of re-sale, and the balance of the costs of purchase and/or manufacture shall be recoverable from the Purchaser forthwith as a debt. 7.. Despatch h and d Deliveryy a) Unless otherwise expressly stated in writing by the Company, the Company will arrange carriage of Goods within the mainland of the United Kingdom and the Purchaser will arrange collection and carriage of Goods ordered for delivery elsewhere. The Company shall only be obliged to deliver Goods to such address as it may have expressly agreed in writing. b) The Purchaser shall sign the delivery note accompanying the Goods at the time of delivery. c) If the Goods and/or Services are not delivered or performed or upon delivery or performance are found to be damaged, short or defective the liability of the Company for any loss of expense of any nature thereby occasioned shall be limited to replacement of damaged Goods and/or Services and/or completion of the delivery of the Goods or the outstanding Goods or performance of the Services. The Company shall not be liable for any further or consequential loss and the Company shall not in any event be liable under this Condition 7(c) to any extent unless:i. the Purchaser gives written notice to the Company and to the carrier on or before signing the delivery note accompanying the Goods and/or Services; and/or ii. in the case of short or damaged delivery or defective performance the Purchaser gives the Company or its nominated representative(s) a reasonable opportunity to inspect the Goods and/or Services concerned in the state and condition and location in which they were delivered or performed; and/or iii. in the case of non-delivery or non-performance the Purchaser gives the Company written notice of such nondelivery or non-performance within 14 days of the expected date of delivery. d) Any stillage pallets or other similar items on which the Goods are delivered shall at all times remain the exclusive property of the Company which shall be allowed to collect them from the Purchaser. In the event of the Purchaser failing to deliver any such items up to the Company in good condition upon being requested to do so the Company may charge the Purchaser for them. e) The risk in the Goods sold shall pass to the Purchaser upon their delivery to the Purchaser if the Company has arranged carriage or upon their transfer at the Company’s premises onto the carrier’s or Purchaser’s transport if the Purchaser has arranged carriage. f) The Purchaser shall keep the Goods fully insured in their full replacement value against all risks prudently insured against at least throughout the period between the risk therein passing to the Purchaser and the property therein ceasing to remain with the Company. g) Any dates quoted for delivery of the Goods and/or performance of the Services are approximate only and the Company shall not be liable for any delay in delivery or performance howsoever caused. Time for delivery or performance shall not be of the essence unless previously agreed by the Company in writing. The Goods may be delivered and/or the Services may be performed by the Company prior to the quoted date if advance notice is given to the Purchaser. h) Where goods are to be delivered and/or the Services are to be performed in instalments, each such delivery and/or performance shall constitute a separate contract and failure by the Company to deliver or perform any one or more of the instalments in accordance with these Conditions or any claim by the Purchaser in respect of any one or more instalments shall not entitle the Purchaser to treat the Contract as a whole as repudiated. i) If the Purchaser fails to take delivery of the Goods or fails to give the Company adequate delivery instructions at the times stated for delivery unless the cause is beyond the Purchaser’s reasonable control or is due to the Company’s fault then without prejudice to any other right or remedy available to the Company the Company may:i. store the Goods until actual delivery and charge the Purchaser all costs (including insurance) of storage incurred; or ii. sell the Goods at the best price readily obtainable and (after deducting all storage and selling expenses) account to the Purchaser for the excess over the price under the Contract or charge the Purchaser for any shortfall below the price under the Contract. 8.. Acceptance e Once the Purchaser has taken delivery of the Goods and/or Services in accordance with these Conditions the Purchaser will be deemed to have inspected the Goods and/or Services and to have intimated to the Company acceptance of them. 9.. Propertyy a) Notwithstanding delivery of the Goods or of any documents representing the Goods, the property in the Goods (and each part of the Goods) shall remain with the Company until the Company has received cash or cleared funds in full payment of the price of Goods and all other Goods agreed to be sold by the Company to the Purchaser under this or any other contract. b) Until such time as the property in the Goods passes to the Purchaser the Purchaser shall hold the Goods as the Company’s fiduciary agent and bailee and shall keep the Goods separate from those of the Purchaser and third parties and properly stored, protected and insured and identified as the Company’s property. c) Notwithstanding that the property in the Goods has not passed to the Purchaser upon receipt of the Goods the Purchaser shall be entitled to resell or use the Goods in the ordinary course of its business but shall account to the Company for the proceeds of sale or otherwise of the Goods whether tangible or intangible including insurance proceeds and shall keep all such proceeds separate from any monies or property of the Purchaser and third parties and in the case of tangible proceeds properly stored protected and insured. d) The Purchaser shall not be entitled to plead or in any way charge by way of security for any indebtedness any of the Goods which remain the property of the Company but if the Purchaser does so all monies owing by the Purchaser to the Company under this or any other contract shall without prejudice to any other right or remedy of the Company forthwith become due and payable. 10.. Generall Liabilitiess a) All warranties, conditions or other terms implied by statute common law trade usage or otherwise are excluded to the fullest extent permitted by law. b) The Company warrants that all Goods and/or Services supplied are at the time of delivery free from defects in materials and workmanship but the Company’s liability under this warranty shall be limited to either:i. making good without charge by repair or replacement or at the absolute discretion of the Company; or ii. refunding the purchase price paid by the Purchaser in respect of any Goods and/or Services which the Company is satisfied were defective in material or workmanship at the time of delivery or performance provided that:i. notice has been given of such defect within 14 days of the date when the Purchaser has inspected or is deemed to have inspected the Goods and/or Services (whichever is the earlier) and in any event within 6 calendar months after the date of delivery or performance; and ii. the Goods are not in any worse condition than when delivered; and iii. this warranty does not extend to any damage which would have been obvious at the time of delivery or performance and which was not notified in writing in accordance with Condition 7(c) above; and iv. this warranty does not extend to defects arising through fair wear and tear, any misuse of the Goods by the Purchaser or any damage caused by the Purchaser failing to follow all instructions issued. c) The liability of the Company for any loss injury or damage of any nature whatsoever (other than personal injury or death caused by the negligence of the Company) arising out of or in connection with any Goods and/or Services supplied under this Contract shall be limited to and not exceed a sum equal to the purchase price of those Goods and/or Services in respect of which any claim arises. The Company shall incur no liability whether for misrepresentation, breach of implied or express warranty or condition or term of breach of duty at common law for any consequential economic loss or damage (whether for loss of profit or otherwise) costs expenses or other claims for consequential compensation whatsoever (and whether caused by the negligence of the Company, its employees or agents or otherwise) arising from or relating to the supply of the Goods or their use or re-sale by the Purchaser and/or the performance of the Services. d) The Purchaser shall not rely upon any representation concerning any Goods and/or Services unless the same shall have been made by the Company in writing. e) The complete or partial invalidity or unenforceability of any provision of these Conditions shall not affect the validity or enforceability of such provision for any other purpose or any of the remaining provisions. 11.. Design n Variationss and d Purchaser’ss Modificationss a) Any variations in the design construction components colour finish or other features of the Goods or in the materials used in the manufacture of the Goods supplied differing from similar Goods previously sold or offered for sale by the Company or in the Company’s trade literature shall not affect the Purchaser’s obligations to accept and pay for the Goods or give rise to any liability on the Company, provided that the variations in question have not resulted in a substantial reduction in the overall quality of the Goods. b) The Purchaser shall not make any modification or alterations to the design or materials comprising the Goods without the prior written consent of the Company. c) If the Company agrees to modify its standard product or manufacture a product to the Purchaser’s design or specification the Purchaser shall indemnify the Company against all actions costs (including the costs of defending any legal proceedings) claims damages or any other expenses whatsoever which may arise by virtue of:i. any defect in any such product save where such defect is not attributable to the Purchaser’s design or specification; or ii. any alleged infringement by such product of any Intellectual Property Rights. 12.. Intellectuall Propertyy a) All Intellectual Property Rights in the Goods and/or the Services shall at all times remain vested in the Company and the Purchaser shall not reproduce or use all or any of them without the Company’s prior written consent. b) The Purchaser will indemnify the Company against any and all damages, penalties, costs, losses and expenses suffered by the Company or for which it may become liable in respect of the infringement of any Intellectual Property Right arising out of the Company’s manufacture of Goods in accordance with any specification, design, drawings, or other data supplied by the Purchaser or its servants or agents. 13.. Use e off the e Goodss a) The Purchaser shall be solely responsible for and shall keep the Company indemnified against any loss liability or expense arising directly or indirectly from the use and/or resale of the Goods:i. other than in accordance with the Company’s installation or operating instructions; and/or ii. in a country where the Goods do not comply with any enforceable restrictions or requirements. b) The Purchaser warrants that the Goods will not be sold distributed or otherwise dealt with in any way without having attached to them all such warnings notices statements or markings of whatsoever nature (in all relevant languages) as may be necessary or appropriate to preclude the making of any claim by any person who may use or be affected by the Goods. The Purchaser shall keep the Company indemnified against any loss liability or expense arising directly or indirectly from the breach of this warranty. 14.. Productt Safetyy a) The Purchaser undertakes to comply with the General Product Safety Regulations 1994 if and to the extent that they are applicable to the Goods. b) The Purchaser undertakes to indemnify the Company in respect of any and all claims arising from the Goods being unsafe as a result of the Purchaser’s activities. c) The Purchaser agrees to pass on any information on the risks of the Goods and to co-operate in any action the Company may decide to take to avoid those risks. d) The Purchaser agrees to keep records of the customers to whom the Goods are sold and to provide the Company with the relevant information should the Company so request. 15.. Force e Majeure e a) If the performance of the Company’s obligations under the Contract is in any way adversely affected by any war strike lock-out sit-in trade dispute flood accident to plant or machinery shortage of any material or labour or by reason of the Purchaser failing to furnish any necessary information or instructions or any other cause whatsoever beyond the Company’s control the Company may give notice in writing to the Purchaser either:i. cancelling forthwith any outstanding obligations of the Company to deliver any Goods and/or perform any Services under the Contract; or ii. extending the time for delivery of the Goods and/or performance of the Services outstanding under the Contract. b) If the Company gives notice under Condition 15(a)(i) above there shall be no liability to the Purchaser for any damages or loss or consequential loss of whatsoever nature and the Purchaser shall remain obliged to pay for any Goods delivered and/or Services performed. c) If the Company gives notice under Condition 15(a)(ii) above then the time for delivery shall be extended accordingly. 16.. Assignmentt The Purchaser shall not assign the benefit of any contract with the Company or any rights hereunder in whole or in part without the prior written consent of the Company. 17.. Third d Partyy Rightss These Conditions do not create, confer or purport to confer any benefit or right enforceable by any person not a party to it. The Contracts (Rights of Third Parties ) Act 1999 is excluded. 18.. Waiverr a) Failure by the Company to enforce any of these Conditions will not be construed as a waiver of any of the Company’s rights hereunder. b) No waiver by the Company of any breach of the Contract by the Purchaser shall be considered as a waiver of any subsequent breach of the same or any other provision. 19.. Defaultt a) The Company may by notice in writing to the Purchaser terminate any contract forthwith if:i. the Purchaser shall commit any breach of any of the Conditions (including without limitation Conditions concerning the time for payment of the purchase price) of this or any other contract with the Company and on its part to be observed or performed provided that if such a breach is remediable the Company has previously given to the Purchaser notice thereof and the same has not been remedied within seven days thereafter; or ii. the Purchaser makes any voluntary arrangement with its creditors or becomes subject to an administration order or (being an individual or firm) dies or becomes bankrupt or (being a company) goes into receivership or liquidation (otherwise than for the purposes of amalgamation or reconstruction) or if any distress or execution is levied upon any of its property or assets or it permits any judgement against it to remain unsatisfied for seven days. b) In the event of any such termination:i. the Purchaser’s right to use or trade in any Goods not yet paid for is immediately suspended; ii. the Purchaser shall forthwith on demand deliver to the Company any Goods the property in which remains with the Company and in default thereof the Company shall be entitled to repossess the same and for such purpose the Purchaser shall afford it access to any premises where such Goods may then be without the Company being liable for any damage caused thereby and the Purchaser shall indemnify the Company from and against any liability to any third party in respect of any such damage and from and against all actions proceedings claims demands costs damages and expenses howsoever arising; and iii. the Company shall be entitled by notice in writing to the Purchaser to declare (and there shall forthwith become) immediately due and payable any amounts outstanding from the Purchaser to the Company under this or any other contract and all such amounts shall bear interest at the rate set out in Condition 5(c) above calculated from the date of the notice until actual payment as well after as before any judgement. c) The provision of Conditions 18(a) and 18(b) above and the exercise by the Company of its rights thereunder are without prejudice to any other rights of the Company. 20.. Freedom m off Information n If the Purchaser (being a public authority) receives an information request under the Freedom of Information Act 2000 relating to any information held regarding the Company, the Purchaser shall consult with the Company prior to releasing any such information. 21.. Headingss The headings used in these Conditions are for convenience only and shall not affect the construction thereof. 02/05 REV 2. distributing power throughout the workplace www.electrak.co.uk Head Office Electrak International Limited No. 1 Industrial Estate Medomsley Road Consett Co. Durham DH8 6SR United Kingdom Tel: 01207 503400 Fax: 01207 501799 Tel Overseas: +44 1207 503400 Email: sales@electrak.co.uk Web: www.electrak.co.uk London Showroom Colonial Buildings 59-61 Hatton Garden London EC1N 8LS United Kingdom Due to our policy of continuous improvement, Electrak reserves the right to change product specification without notice. Errors and omissions expected.
