Connectors

Connectors
Overview
3G Transmission Design
■ What is 3G-SDI?
■ SMPTE Performance Requirements
3G-SDI is a new transmission format (1080p) that offers twice the data
carrying capacity (bandwidth) of today’s widely used HD-SDI (1080i).
SMPTE ST 424 covering this format includes regulations for the coaxial
connectors and cables used for transmission, and Canare’s 751 products
already meet the performance requirements for these.
Format
3G-SDI
SMPTE ST 424
1.485Gbps
2.97Gbps
Transmission Bit Rate
Characteristic Impedance (Zo)
■ Signal Attenuation in 3G Transmission Lines
In order to keep overall transmission line attenuation below the 30dB loss
budget, it is necessary to calculate attenuation amounts individually for each
section in the system. In the system shown below, the losses occurring
within each transmission line have been calculated and entered into a level
diagram. From this it is possible to see the differences in transmission
distances possible with HD-SDI and 3G-SDI when using a coaxial cable
(L-7CHD). If this shows that attenuation will surpass the specified loss
budget, then it will be necessary to change to cables with less attenuation,
or to revise the circuit and/or equipment layout to compensate. It is also
recommended that these calculations include a 2–3dB design margin.
<System Example>
HD-SDI
SMPTE ST 292
751
Transmission Line Attenuation
20dB @742.5MHz
30dB @1.485GHz
Transmission Line Return Loss
15dB or greater
@5M~1.485GHz
15dB or greater
@5M~1.485GHz
10dB or greater
@1.485~2.97GHz
HD Equipment
4
BCJ-JR
3
L-4.5CHD
5
6m
L-7CHD
105m
2
HD-SDI
125m
3G-SDI
105m
8
BCJ-JR
DVJB-W
9
L-2.5CHD
2m
DVJB-W
HD Equipment
6
BCJ-JR
1
L-2.5CHD
7
2m
L-4.5CHD
6m
Rack/Between the Racks
Between the Rooms
Rack/Between the Racks
<Level Diagram>
1
2
3
4
Attenuation (dB)
0
5
6
7
8
9
Margin
-20
■ System Attenuation
Format
Connector/
Cable
m or pcs
HD-SDI
Loss
(dB/m)
Loss (total)
(dB)
m or pcs
3G-SDI
22
Loss
(dB/m)
Loss (total)
(dB)
ᆰ
L-2.5CHD
ᆱ
DVJB-W
ᆲ
L-4.5CHD
ᆳ
BCJ-JR
ᆴ
L-7CHD
ᆵ
BCJ-JR
ᆶ
L-4.5CHD
ᆷ
BCJ-JR
ᆸ
L-2.5CHD
2
1
6
1
125
1
6
1
2
0.3
0.9
0.2
0.2
0.1
0.2
0.2
0.2
0.3
0.6
0.9
1.2
0.2
12.5
0.2
1.2
0.2
0.6
2
1
6
1
105
1
6
1
2
0.4
0.9
0.3
0.2
0.2
0.2
0.3
0.2
0.4
0.8
0.9
1.8
0.2
21.0
0.2
1.8
0.2
0.8
Connectors
Sub Total
Margin
Total
Amount
17.6dB
2.4dB
20.0dB
27.7dB
2.3dB
30.0dB
Active BNC
751 Active BNC Receptacles
Model
Description
Fiber-Optic Systems
Small BNC connector incorporates either a cable equalizer or a cable driver.
Active BNC makes innovation in your 3G-SDI PC board layout.
Built-in IC
BCA-TL
TX, Right Angle
Cable Driver
BCA-RL
RX, Right Angle
Cable Equalizer
BCA-TS
TX, Straight
Cable Driver
BCA-RS
RX, Straight
Cable Equalizer
BCA-TL
BCA-RS
(Right Angle)
(Straight)
• Standard package (5pcs)
Impedance of PCB
BNC Connector
Built-in
Digital Signal
Processing Part
Digital Signal
Processing Part
50Ω
50Ω
Cables
I/O
75Ω
I/O Block
Impedance of PCB
Active BNC
Connectors
● BNC connector integrated with a cable equalizer or a cable driver, and yet keep the
connector size to a minimum.
● Supports 3G-SDI, HD-SDI, SD-SDI and DVB-ASI
● Offers an excellent return loss performance without designing 75 ohm I/O block
● Simplifies PCB design process dramatically and will reduce entire development cost
● PCB space saving and help to downsize devices
● Easy to distinguish TX from RX by color-coded insulation
Space-saving
Simplify Your Circuit Design
3G-SDI
SG
Specifications
DC 3.3V
L-5CFB
1m
L-5CFB
50mA
70mA
Operating Temperature
-25°C to +85°C
Output Signal Amplitude
800mVpp
Equalizing Cable Length
—
3G-SDI 120m w/L-5CFB
Weight
SMPTE
424M
10
20
30
Approx. 9.0g
40
US Patent No.: 8251721 B2
JP Patent No.: 4837715
0
Panel Hole Dim.
BCA-RL
1.5
3.0
(GHz)
BCA-TS
BCA-RS
3.4max
2.
1
5
φ
.6
3.04 5.9
1
2.
φ
1.27
3.04 5.9
3.4max
10.16
1：GND
2：SDI+
3：SDI −
4：Vcc
5：SD/HD
P =1.27 6 ： −
7：−
8：ENABLE
0
φ
4-
2.7×3.6
3
2-
φ
1.
4321
1：GND
2：SDO−
3：SDO+
4：Vcc
P =1.27
10.16
t2.0
t2.0
(TOP VIEW)
(TOP VIEW)
Note: The darker shaded area will come into contact with the connector body.
P=1.27
9.64
Connectors
4
φ
1.
φ
0.
2-
6
4321
8
1：GND
2：SDI+
3：SDI−
4：Vcc
5：SD/HD
6：−
7：−
8：ENABLE
t2.0
(TOP VIEW)
4-
1.4
2
123 4
4
1.
φ
2-
1.27
1.15
3
1.
1234
6
6-
2.7×3.6
7
0.
φ
φ
6
0.
5
6-
8
t1.6 Screw: M2.6
Cable Assemblies
t1.6 Screw: M2.6
7
Mutichannel Systems
50
BCA-TL
-φ
Eye Pattern ( 3Gbps )
Return Loss
(dB)
0
—
SMPTE424M, 292M, 259M,
BTA S-004C, EN50083-9,
RoHS
Compliant
PCB Hole Dim.
BNC
RX
BCA-RL, BCA-RS
Supply Voltage
Current Consumption
Active
BNC
Panels & Patchbays
TX
BCA-TL, BCA-TS
Model
Active
P=1.27
9.64
1：GND
2 ： S D O−
3：SDO+
4：Vcc
t2.0
(TOP VIEW)
23
Connectors
751 DIN Connectors
751 DIN1.0/2.3 Connectors
Mini coax connectors IEC61169-29 and DIN 47 297 compatible.
■ DCP-C Series (Crimp Plugs)
Model
DCP-C25HD
DCP-C3F
DCP-C4F
DCP-C53
VSWR 1.2@ 3GHz
Suitable Cable
Canare
Others
L-2.5CHD, L-2.5CHLT
1855A, VDM230
L-3CFB
—
L-4CHD, L-4CFB
1505A, VPM2000
L-4.5CHD
1694A, VSD2001
Center
Pin
Sleeve
Boot
Die Set
BN1148
BN1148
BN1158
BN1157
BN7136
BN7003A
BN7015A
BN7138
—
—
—
—
TCD-D253F
TCD-D253F
TCD-D534F
TCD-D534F
DCP-C25HD
•Standard package (20pcs/100pcs)
● Our unique ball-locking mechanism offers smooth and reliable mating.
● Canare crimp design ensures quick and reliable installation.
● Elongated body design enables stable finger grip.
● Return loss: 20 dB or greater up to 3GHz
● Extraction tool : BET-DIN (see page 38)
DCP-C25HD
US Patent No.: 8764473 B2
Be sure to use Canare crimping tool for installing connectors on cables
■ PCB Mount Receptacles
7
VSWR 1.2 @ 3GHz
Description
Right Angle
Right Angle, Long type
Edge Mount
20.84
Nut Driver Bit
φ4.1
Model
DCJ-LR
DCJ-LR/1
DCJ-FEM
Rerurn Loss for DCP-C25HD
NDT-DIN
DCJ-LR
• Standard package (20 pcs)
● Compact design ideal for high density
mounting and downsizing devices.
● Combination of DCJ-LR/1 and DCJFEM will be effective for staggered
arrangement.
● Return loss: 20 dB or greater up to 3
GHz.
0.8
DCJ-LR/1
Note: Nut driver bit NDT-DIN is required.
Rerurn Loss for DCJ-LR
■ Adapters
Model
DCJ-JR
BCJ-DCJ
BCP-DCJ
DCJ-FEM
VSWR 1.1 @ 3GHz
Description
Panel Mount
Jack to Jack
Yes
BNC Jack to DIN1.0/2.3 Jack
Yes
BNC Plug to DIN Jack
No
Nut Driver Bit
NDT-DIN
N/A
N/A
•Standard package (20 pcs)
DCJ-JR
● Return loss: 26 dB or greater up to 3 GHz.
Note: Nut driver bit NDT-DIN is required for DCJ-JR
<Panel Hole Dim.>
DCJ-LR
DCJ-LR/1
DCJ-FEM
DCJ-JR
<PCB Hole Dim.>
BCJ-DCJ
DCJ-LR
DCJ-LR/1
DCJ-FEM
BCJ-DCJ
t2.0
t2.0
t1.6
BCP-DCJ
■ Nut Driver Bit
Model
NDT-DIN
Description
6.35mm (1/4") hex shank
NDT-DIN
24
Connectors
Ѯ4.1
CANARE
27.95
751 Multichannel Coax Connectors
Fiber-Optic Systems
4K-DIN Coax Connectors
Canare unique "4K-DIN" allows you to connect or disconnect 4 of 3G-SDI signals in one easy step.
■ Crimp Plugs
Suitable Cable
Die Set
Description
MDM-V4C25HW
V4-2.5CHW
TCD-D253F
Male
MDF-V4C25HW
V4-2.5CHW
TCD-D253F
Female
9
(92)
(q 28.4)
Model
MDM-V4C25HW
MDM V4C25HW
■ Flush-mount Receptacle
Jack to Jack
Connectors
● 751 4-channel coax connector with push-pull locking mechanism.
● Compact, solid, and lightweight nylon resin (PA 66) body
● Return loss: 20 dB @ 3 GHz
● MDF-V4JRU accepts MDM-V4C25HW and also DIN 1.0/2.3 plugs.
* Replacement crimp units also available:
DCP-C25HW-ML for MDM
DCJ-C25HW-ML for MDF
27.4
<Connection Example>
751DIN1.0/2.3connector
×4
31
q 23.95
MDF-V4C25HW
q 22.4
MDF-V4JRU
(103.8)
Description
q 28.6
Model
26
MDF-V4JRU
MDF-V4JRU
MDM-V4C25HW
Hole Dimensions
4
24
q2
MDM-V4C25HW
Cables
Ex. 1
MDF-V4C25HW
Ex. 2
19
Min. 44mm pitch
(recommended)
Be sure to use the Canare crimping tool for installing connectors on cables.
Panels & Patchbays
751 Multi-pin Coax Connectors
Single connector handles load of up to five 751 coaxial connectors.
V5-3C
TCD-35CA
Plug
MCF-V5C3
V5-3C, L-3C2V, L-3C2VS
TCD-35CA
Receptacle
MCM-V5C3
MCF-V5C3
(98)
(41.9)
M39x1.5
CANARE
MCM-V5C3
∅36
Description
∅29
Die Set
∅42
Suitable Cable
∅34.4
Model
(8.8)
Description
(26.2)
Mutichannel Systems
Model
● 1.2 or less VSWR up to 1.5GHz.
● Crimp system ensures quick and reliable installation.
1
4
41.3
Panel Hole
Dimensions
(Mounting screw
M3 x 4 pcs)
31.98
Dust Cap for MCF-V5C3
5
31.98
DCF01
3.8
4−∅
∅3
7
Dust Cap for MCM-V5C3
∅3
.66
Key
DCM01
2
3
31.98
31.98
41.3
* Replacement unit also available. MCM-V5C3: BN9078A MCF-V5C3: BN9079B
Replacement Unit BN9078A
Be sure to use the Canare crimping tool for installing connectors on cables.
Replacement Unit BN9079B
Cable Assemblies
Connectors
25
Connectors
751 BNC Connectors
751 BNC Crimp Plugs
Canare True 75 1 BNC Connectors has been widely used in the world with quick and reliable crimp design, and
outstanding performance. The high-end model BCP-B series are specially designed for particular coax cables, and
minimize return loss at 3 GHz.
■ BCP-B Series
Model
BCP-B25HD
BCP-B25HW
BCP-B26
BCP-B28
BCP-B3F
BCP-B31F
BCP-B4F
BCP-B45HW
BCP-B53
BCP-B56
BCP-B5F
BCP-B51F
VSWR 1.1@ 3GHz
Suitable Cable
Canare
Others
L-2.5CHD, L-2.5CHLT
VDM230
V4-2.5CHW
—
—
1855A, 1855P
1855ENH,
—
HD PRO 0.6/2.8 AF
L-3CFB, V*-3CFB
—
L-3CFW, V*-3CFW
—
1505A, 1505ANH, VPM2000,
L-4CHD, L-4CFB, V*-4CFB
HD PRO 0.8/3.7 AF
L-4.5CHWS
1694F
L-4.5CHD
1694A
—
HD PRO 1.0/4.8 AF
L-5CFB, V*-5CFB
—
L-5CFW, V*-5CFW
—
Center Pin
Sleeve
Boot
Die Set
B11015E
B11015E
B11014E
BN7129
BN7143
BN7029C
CB02
CB02
CB02
TCD-35CA
TCD-35CA
TCD-35CA
B11015E
BN7052A
CB02
TCD-35CA
B11015E
B11015E
BN7003A
BN7015A
CB03
CB04
TCD-35CA
TCD-4CA, TCD-451CA
B11016E
BN7015A
CB04
TCD-4CA, TCD-451CA
B11020D
B11020D
B11020D
B11020D
B11020D
BN7016
BN7046
BN7046
B75004A
B75004A
CB05A
CB05A
CB05A
CB05A
CB05A
TCD-35CA
TCD-35CA
TCD-35CA
TCD-5CF, TCD-55FA
TCD-5CF, TCD-55FA
BCP-A32
BCP-A3F
BCP-A4
BCP-A42
BCP-A4F
BCP-A5
BCP-A52
BCP-A55
BCP-A5F
BCP-A77
BCP-VA3
BCP-VA5
Others
L-2.5C2V
—
L-2.5CFB
1855A, 8218, 1417B, 1418B
L-3C2VS, L-3C2V, V*-3C
—
L-3C2W
—
1506A, 1824A, 1825A, 1826A,
—
643948
L-3CFB, V*-3CFB
—
LV-61S
8241, 8279, RG-59B/U
—
1505F
1505A, 1505ANH, 8212,
8241F, 9167, 9259, 9659,
L-4CHD, L-4CFB, V*-4CFB
VPM2000,
HD PRO 0.8/3.7 AF
L-5C2VS, L-5C2V, V*-5C
—
L-5C2W
—
—
1695A, VSD2001TS
L-5CFB, V*-5CFB
—
LV-77S
8281F
V*-3C
—
V*-5C
—
Center Pin
Sleeve
Boot
Die Set
BN1018A
B11014E
B11014E
B11014E
BN7029C
BN7029C
BN7003A
BN7011
CB02
CB02
CB03
CB04
TCD-35CA
TCD-35CA
TCD-35CA
TCD-31C
B11016E
BN7026A
CB03
TCD-35CA
B11015E
B11015E
B11016E
BN7003A
BN7015A
BN7011
CB03
CB04
CB04
TCD-35CA
TCD-4CA, TCD-451CA
TCD-31C
B11016E
BN7015A
CB04
TCD-4CA, TCD-451CA
BCP-C7FA
BCP-C7HD
B11016E
B11016E
B11020D
B11020D
B11016E
B11014E
B11016E
BN7016
BN7014
BN7045A
B75004A
B75004A
BN7052A
BN7045A
1.5
3.0
(GHz)
Return loss for BCP-B53
BCP-A3
CB05A
—
CB04
CB05A
CB05A
CB03
CB05A
TCD-35CA
TCD-451CA
TCD-35CA
TCD-35CA
TCD-5CF-TCD-55FA
TCD-35CA
TCD-35CA
VSWR
SMPTE424M
1.3
1.2
-20
1.1
-30
-40
-50
0
1.5
3.0
(GHz)
Return loss for BCP-A3
*1: Excluding BCP-A25, BCP-A25F, BCP-A4
Canare
L-1.5C2VS, V*-1.5C
L-5CHD
L-6CHD
—
L-7CFB
L-7CHD
Others
83264, 83267
—
—
7731A, 9064, 9292, 1617A,
9011
—
—
Center Pin
Sleeve
Boot
Die Set
Solder
BN1139
BN1083A
BN7022
B75004A
BN7074A
CB01
CB05A
—
TCD-1DB
TCD-5HD
TCD-67HD
BN1043A
BN7021A
—
TCD-7CA
BN1012B
BN1082A
BN7021A
BN7021A
• Standard package (20pcs/100pcs).
—
—
TCD-7CA
TCD-67HD
*2: Excluding BCP-C1
● Canare crimp design ensures quick and reliable installation.
● Gold plated "snap locks" center pin and beryllium copper outer contact.
● Elongated body design enables stable finger grip (excluding BCP-C1).
● Position mark on the BCP-B/A series body makes it easier to check if the connector is locked.
Note: Die set for BCP-A5F is TCD-35CA
BCP-C6HD
S11(dB)
0
VSWR
SMPTE424M
-10
1.3
1.2
-20
1.1
-30
-40
-50
0
1.5
3.0
(GHz)
Return loss for BCP-C6HD
Be sure to use the Canare crimping tool for installing connectors on cables.
26
0
VSWR 1.1 @ 2GHz (*2)
Suitable Cable
BCP-C71A
-40
-10
■ BCP-C Series
Model
1.1
-30
S11(dB)
0
• Standard package (20pcs/100pcs).
Note: Suitable die set for BCP-A5F is TCD-35CA; do not use TCD-5CF/TCD-55FA for BCP-A5F.
BCP-C1
BCP-C5HD
BCP-C6HD
1.3
1.2
-20
VSWR 1.1 @ 2GHz, VSWR 1.2 @ 3GHz(*1)
Suitable Cable
Canare
VSWR
-10
-50
■ BCP-A Series
BCP-A25
BCP-A25F
BCP-A3
BCP-A31
Return loss
(dB)
0
SMPTE424M
• Standard package (20pcs/100pcs)
Model
BCP-B5F
BCP
B5F
Connectors
751 BNC Connectors
75 1 BNC Crimp Plugs (Right Angle Type)
Model
BCP-LC3
BCP-LC3F
BCP-LC5
BCP-LC5F
Fiber-Optic Systems
■ BCP-LC Series
VSWR 1.1@ 2GHz
Suitable Cable
Canare
L-3C2VS, L-3C2V,V*-3C
L-3CFB, V*-3CFB
L-5C2VS, L-5C2V, V*-5C
L-5CFB, V*-5CFB
Others
—
—
—
—
Center Pin
Sleeve
Boot
Die Set
B11014E
B11015E
B11016E
B11020D
BN7003A
BN7003A
BN7016
B75004A
—
—
—
—
TCD-35CA
TCD-35CA
TCD-35CA
TCD-5CF, TCD-55FA
• Standard package (20pcs)
● Canare crimp design ensures quick and reliable installation.
● Gold plated "snap locks" center pin and beryllium copper outer contact.
BCP-LC3
Connectors
Be sure to use the Canare crimping tool for installing connectors on cables.
75 1 Slim BNC Crimp Plugs
■ MBCP-C Series
Model
MBCP-C25F
MBCP-C3F
MBCP-C4
VSWR 1.1@ 1.5GHz
Suitable Cable
Canare
L-2.5CFB
L-3CFB, V*-3CFB
LV-61S
L-4CFB, V*-4CFB
L-4.5CHD
L-5CFB, V*-5CFB
Center Pin
Sleeve
Boot
Die Set
B11014E
B11015E
B11015E
BN7029C
BN7003A
BN7015A
—
CB24
CB25
TCD-35CA
TCD-35CA
TCD-4CA, TCD-451CA
B11016E
BN7015A
CB25
TCD-4CA, TCD-451CA
B11020D
B11020D
BN7046
B75004A
CB26
CB26
TCD-35CA
TCD-5CF, TCD-55FA
Cables
MBCP-C4F
MBCP-C53
MBCP-C5F
Others
1855A, 8218, 1417B, 1418B
—
8241, 8279, RG-59B/U
1505A, 1505ANH, 8212, 8241F,
9167, 9259
1694A, 9066, 9116, 9118, 9248
—
• Standard package (20pcs/100pcs)
Body
∅12
CANARE
Crimp sleeve
15
Center contact
26.35
(10.7)
MBCP-C3F
Conventional BNC Plug
Slim BNC Plug
Return loss
VSWR
(dB)
0
Be sure to use Canare crimping tool for installing connectors on cables.
SMPTE424M
-10
1.3
1.2
-20
Panels & Patchbays
● Slim design: OD 12 mm
● Compatible with 75 1 BNC receptacles.
● Canare crimp design ensures quick and reliable
installation.
● Gold plated "snap locks" center pin and beryllium copper
outer contact.
1.1
-30
-40
-50
0
1.5
3.0
(GHz)
Mutichannel Systems
Return loss for MBCP-C3F
Technical Note
Voltage Standing-wave Ratio (VSWR) and Return Loss
Voltage
Vmax
Vmin
Coaxial cable distance
Fig. 1 Voltage Distribution Over
Coaxial Cable
VSWR
2
1.5
1.2
1.1
1.05
1.02
1.01
Return Loss (dB)
9.5
14
20
26
32
40
46.1
Cable Assemblies
Terminating the receiving end of a limited length coaxial cable using
a resistance value not equal to its characteristic impedance creates a
reflected wave that returns back down the cable to the sending end. The
result is interference developing between the travelling wave and the
return wave which results in a standing wave that causes voltage levels
to fluctuate. The degree to which terminating resistance matches the
characteristic impedance is indicated using the VSWR or voltage standingwave ratio standard shown in Fig. 1. Going hand in hand with the VSWR
ratio is the return loss factor which measures the size of the reflected wave
current in relation to the travelling wave current. (See Fig. 2)
Fig. 2 VSWR to Return Loss
Conversion Table
Connectors
27
Connectors
751 BNC Connectors
751 BNC Solder Plugs
■ BCP-H Series
Model
BCP-H3B
BCP-H31F
BCP-H45HW
BCP-H5B
BCP-H51F
BCP-H5/1
VSWR 1.1@ 1GHz
Return loss
(dB)
0
Suitable Cable
Canare
L-3C2VS, L-3C2V, L-3CFB
L-3CFW
L-4.5CHWS
L-5C2VS, L-5C2V, L-5CFB
L-5CFW, L-5CFB
L-3C2VS, L-3C2V, L-3CFB
L-5C2VS, L-5C2V, L-5CFB
VSWR
SMPTE424M
Others
—
—
1694F
—
—
-10
1.3
1.2
-20
1.1
-30
BCP-H3B
BCP H3B
-40
—
-50
0
1.5
3.0
(GHz)
• Standard package (20pcs)
● The tubular (ferrule) section is silver plated to make soldering easier.
● Cable stripper TS100E can be used. (Excluding BCP-H31F, BCP-H51F)
Return loss for BCP-H3B
Model
BCJ-C4
Suitable Cable
RG-59 B/U, LV-61S,
Belden 8241, 8279, 88241
Boot
CB25
∅ 12
751 BNC Jack Plug
Die Set
TCD-4CA
TCD-451CA
35.2
BCJ-C4
•Standard package (20pcs)
BCJ-C4
BCJ C4
● 1.1 or less VSWR up to 1.5GHz, 1.2 or less up to 2.4GHz.
● Beryllium copper (gold plated) is used on the center contact for its
superior spring characteristics. (Center contact: solder)
Be sure to use the Canare crimping tool for installing connectors on cables.
BCJ-J
Return loss
(dB)
0
751 BNC Extension Adapter
VSWR
SMPTE424M
Model
BCJ-J
-10
Description
1.3
1.2
-20
Jack to Jack
1.1
BCJ-J
•Standard package (20pcs/100pcs)
-30
● Beryllium copper is used on the center contact for its superior spring
characteristics.
● 1.1 or less VSWR up to 2GHz. <Fig. 1>
-40
-50
0
1.5
3.0
(GHz)
Fig.1 Return loss for BCJ-J
Return loss
(dB)
0
751 BNC Termination Plugs
Designed for true 751 termination
VSWR
SMPTE424M
-10
1.3
1.2
-20
Model
BCP-TA
BCP-TA-CH
Description
Standard 751 Termination (2.0GHz Type)
Standard 751 Termination (2.0GHz Type) with String
1.1
-30
-40
BCP-TA
-50
•Standard package (20pcs/100pcs)
0
1.5
3.0
(GHz)
Fig.2 Return loss for BCP-TA
● Includes 1/4 watt resistance.
● 1.1 or less VSWR up to 2GHz. <Fig. 2>
BCP-TA
Connector Boots
■ CB0x Series
Our best selling connector boots for Canare BNC, TNC crimp plugs.
BP-xx
TNP-xx
C3, C4
C31
C5, C5FA
CB24
CB25
CB26
Colors Available
C3F
BLK, BLU, GRN, RED, YEL, WHT C4, C4F
C5F
MBCP-xx
Typical Connectors
RCAP-xx
C3A, C3F
C3GS, C4A, C4F
C53, C5A, C5F
7.1
∅12.7
■ CB2x Series
Thinner type of CB0x series. Best fit for Canare Slim BNC, RCA, and F crimp plugs.
Model
CB03, CB04, CB05A
C3, C4
C31
C5
∅6.58
Colors Available
BCP-xx
BLK, BLU, GRN, RED, YEL, WHT C1
B25HD, B25HW, B26, B28, A25, A25F
B3F, B31F, A3, A32, A3F, VA3
BLK, BLU, BRN, GRN, GRY,
ORN, PPL, RED, YEL, WHT
B4F, A31, A4, A42, A4F, A55
B53, B56, B5F, B51F, A5, A5F, A77, VA5, C5HD
28
CB01, CB02
FP-xx
C3, C3F
C31, C4, C4F
C5, C53A, C5F
∅10
Model
CB01
CB02
CB03
CB04
CB05A
28
28
CB24, CB25, CB26
Connectors
751 BNC Connectors
Fiber-Optic Systems
751 BNC Receptacles
BNC Receptacles emphasizing true 751 impedance.
■ Standoff Receptacles
—
—
1.5C-2V
10.9
TCD-1DB
—
—
9.6
BCJ-R
12.1
3.5max
BCJ-FC1-7/16
BCJ-FC1-7/16
" 16
Jack to Solder
Jack to Solder w/Ground Lug
Panel Jack (1/2")
Panel Jack (7/16")
Jack to Jack
BCJ-R/1
Die Set
ARE
BCJ-R
BCJ-R/1
BCJ-FC1
BCJ-FC1-7/16
BCJ-JR
BCJ-R/1
Suitable
Cable
—
—
Description
" 14
Model
•Standard package (20pcs/100pcs)
20.5
Model
Description
BCJ-RU
BCJ-RUD
BCJ-RUDB
BCJ-RUC1
BCJ-JRU
BCJ-JRUD
BCJ-JRUDB
Jack to Solder
Panel Jack
Jack to Jack
12.1
BCJ-FC1
Flange
Type
ITT XLR-F77
Neutrik D
Neutrik D (Black)
ITT XLR-F77
ITT XLR-F77
Neutrik D
Neutrik D (Black)
Suitable
Cable
—
1.5C-2V
—
—
—
—
—
Die Set
—
TCD-1DB
—
—
—
—
—
BCJ-JR
BCJ-JR
BCJ JR
Connectors
■ Flush-mount Receptacles
7.2
•Standard package : 20pcs
BCJ-RU
Cables
● VSWR 1.1 @ 2GHz (Panel Jack: 1.1 @ 1GHz)
● Gold plated beryllium copper center contact
● Flush-mount receptacle prevents damage on the jack.
BCJ-RU
Standard design Canare BCJ-RU design
Panels & Patchbays
BCJ-RUC1
Registered design
BCJ-RUC1
BCJ-JRU
★BCJ-FC1-7/16
BCJ-RUC1
BCJ-RU
BCJ-JRU
BCJ-RUD
BCJ-RUDB
BCJ-JRUD
BCJ-JRUDB
BCJ-JRU
21.4
BCJ-FC1
23
★BCJ-R/1
★BCJ-JR
Mutichannel Systems
BCJ-R
BCJ-
■ Panel Hole Dimensions
2−∅ 3.4
2.7
25.2
.6
23
24
∅
4.7
BCJ-RUD
19
ITT XLR-F77
Compatible
★ Indicate connectors that accept insulation bushing. Mounting hole for insulation bushing
IU 7/16 should be adopted.
BCJ-RUD
C
31
Insulation Bushing
Cable Assemblies
Model
IU-7/16
Neutrik D
Compatible
Description
ABS plastic
26
•Standard package: 20pcs
∅ 17.5
∅ 15
∅ 12.7
IU-7/16
∅ 12.8
∅
9.6
11.1
15
Mountable panel thickness:
1.2~1.5mm: BCJ-FPLVA, BCJ-FPLHA, BCJ-R/1
1.2~3.0mm: BCJ-FPC, BCJ-FPC02, BCJ-JR, BCJ-FPLV01
∅ 11.2
15
.6
Note: Please remove washers from a connector before using IU-7/16.
2.5
3.5
1
● Insulate a connector from a panel.
● 5 colors available (white, black, blue, green, red, or yellow)
∅ 12.8
Panel Hole Dimensions
Connectors
∅ 11.2
∅ 12.8
29
Connectors
751 BNC Connectors
751 BNC PCB Mount Receptacles (Screw Type)
■ BCJ-BP Series
Model
Stud
Position
Description
BCJ-BPLHA
BCJ-BPLH2PA
BCJ-BPLH3PA
BCJ-BPC2P
Right Angle
Right Angle, Dual Jack
Right Angle, Triple Jack
Straight, Dual Jack
Panel Mount
Standard Package
Front:
M2.6 screw
20 pcs/100pcs
10 pcs
10 pcs
10pcs/100pcs
Horizontal
—
* Screws are not included.
Key Features and Benefits
● True 751 PC board mount receptacle.
● VSWR 1.1 or less up to 1.5GHz, 1.2 or less up to 3GHz.
(1.1 or less up to 1GHz, 1.2 or less up to 2.5GHz for BCJ-BPC2P.)
● Gold plated beryllium copper center contact.
● Can be fixed on the PC board with M2.6 screw for efficient soldering.
(excluding BCJ-BPC2P)
● Space-saving design allows high-density mounting.
● Eliminates wiring material and cost.
BCJ-BPLHA BCJ-BPLH2PA BCJ-BPLH3PA
7.5
4.75
∅ 9.5
(28.94)
14.5
BCJ-BPLHA
BCJ-BPLHA
(29.24)
16
∅ 9.5
14.5
M2.6
Note: Any cleaning solvents cannot be used. This leads to insulation problems.
Insulation material: m-PPO (m-PPE)
Return loss
(dB)
0
VSWR
-10
-10
1.3
1.2
-20
-30
BCJ-BPLH2P
BCJ-BPLHA
-40
-40
-50
-50
1.5
3.0
(GHz)
BCJ-BPLH2PA
0
1.5
-50
3.0
(GHz)
0
1.5
3.0
(GHz)
Return loss for
BCJ-BPC2P
2
Comparison with the previous model
BCJ-BPLH2PA
BCJ-BPLH3PA
BCJ-BPC2P
4
4
8
9.6
1.3
16
16
Screw: M2.6 t1.6
16
t2.0
(BOTTOM VIEW)
3-∅
7.64
4
1.
4−
∅
1x
1.
8
0.6
3
t2.0
(BOTTOM VIEW)
10.16
10.16
t2.0
(BOTTOM VIEW)
Connectors
10.16
2.54
∅
2.1
1.
1.3
6.4
2-2.7X3.5
5−∅
10.16
16.5
3.4MAX
?
∅
∅
5.08
6.4
5.08
7
9-
2.7×3.5
Screw: M2.6 t1.2
16
7
7
4(?
3.4max
∅ 2.1
16
Screw: M2.6 t1.6
PCB Hole Dim.
;(7
4
9.6
9.6
∅1
Screw: M2.6 t1.6
30
4
7
2.
∅
8
2-
7
2.
∅
7
2.
∅
.3
3
8
11
.
11
.95
R2
;(7
14
BCJ-BPLH3PA
∅
3-
7
4
BCJ-BPC2P
∅
2-
Panel Hole Dim.
BCJ-BPLHA
17.5
-40
9L[\YUSVZZMVY
)*1)73/7)*1)73/7(
Return loss for
BCJ-BPLH, BCJ-BPLHA
10.9 3.1
1.1
-30
-30
0
1.3
1.2
-20
1.1
1.1
∅ 9.5
BCJ-BPLH
1.3
1.2
-20
BCJ-BPC2P
SMPTE424M
SMPTE424M
SMPTE424M
-10
VSWR
∅ S11(dB)
0
VSWR
BCJ-BPLH2PA
16.5
∅ 9.5
Return loss
(dB)
0
TAP
t1.6
(BOTTOM VIEW)
751 BNC Connectors
751 BNC PCB Mount Receptacles (Hex Nut Type)
Description
Right Angle
Right Angle, Low-cost Model
Right Angle (10pcs)
Right Angle
Straight
Straight, Low-cost Model
Stud Position
Panel Mount
Vertical
Front:
Hex nut and
lock washer
Horizontal
BCJ-FPLV01
BCJ-FPC02
—
3max
(16.17)
•Standard package (20pcs/100pcs)
■ BCJ-RP Series
Description
Right Angle
Right Angle
Straight, Through Hole Mount
Straight, Surface Mount
Stud Position
Vertical
Horizontal
—
Panel Mount
10.9
Rear:
Hex nut and
lock washer
7.25 7.3
BCJ-FPLVA
BCJ-RPC/1
Return loss
(dB)
0
VSWR
4max
SMPTE424M
•Standard package (20pcs/100pcs)
5.08
Connectors
Model
BCJ-RPLV
BCJ-RPLH
BCJ-RPC
BCJ-RPC/1
4.7
7.5
Model
BCJ-FPLVA
BCJ-FPLV01
BCJ-FPLV-L
BCJ-FPLHA
BCJ-FPC
BCJ-FPC02
Fiber-Optic Systems
■ BCJ-FP Series
2.3 2.1
-40
Straight Type
-50
BCJ-RPLH
0
1.5
10.9
9.6
5.08
Return loss for
BCJ-FPLVA, BCJ-RPLH
Return loss
(dB)
0
0.6
5
0.3
3.0
(GHz)
7.5
4.7
(16.17)
1.1
BCJ-FPLVA
-30
BCJ-FPLV01
VSWR
Cables
Right Angle Type
1.3
1.2
-20
Note: Any cleaning solvents cannot be used. This leads to insulation problems.
Insulation material: m-PPO (m-PPE)
RE
● VSWR 1.1 or less up to 1GHz, 1.2 or less up to 2.5GHz.
(1.1 up to 3GHz for BCJ-FPLV-L)
● Gold plated beryllium copper center contact.
∅ 14
-10
3max
SMPTE424M
（16.17）
-10
1.3
1.2
-20
1.1
-30
25.5
BCJ-FPLV01
-40
BCJ-FPLV-L
BCJ-FPLVA
BCJ-FPLV01
BCJ-FPC
BCJ-FPC02
-50
0
1.5
3.0
(GHz)
2.5
Return loss for
BCJ-FPLV01, BCJ-FPLV-L
BCJ-FPLV-L
VSWR
Panels & Patchbays
Return loss
(dB)
0
3.5
18.3
SMPTE424M
-10
BCJ-FPLHA
BCJ-RPC
BCJ-RPC/1
4.5max
1.3
1.2
-20
BCJ-FPC02
-40
-50
BCJ-RPC
BCJ-FPC
0
1.5
10.9
3.0
(GHz)
Return loss for
BCJ-FPC, BCJ-FPC02,
BCJ-RPC
BCJ-RPLV
BCJ-FPC
Panel
BCJ-FPLV-L
4.5max
2.1
(16.17)
0.8
RE
10
BCJ-FPLVA
PC Board
10.9
* BCJ-FP series accept insulation bushing IU-7/16.
Mounting hole for IU-7/16 should be adopted. (See page 29)
1.2
BCJ-RPC/1
BCJ-RPC BCJ-RPLV
BCJ-RPLH
18
BCJ-FPLHA*
BCJ-FPC*
BCJ-FPC02*
1.4
9.6
3.5
27.5
BCJ-FPLV-L can be
stacked over BCP-FPLVA
on a PCB as shown.
BCJ-FPC02
BCJ-RPLV
BCJ-RPLH
2max
BCJ-RPC
3
φ8.4
BCJ-FPC
BCJ-FPC02
φ13
BCJ-FPLV-L
10.9
2
15
2.5
BCJ-RPC
t 2.0
t 2.0
t 2.0
t 3.0
Connectors
t 1.6
31
Cable Assemblies
<PC Board Hole Dimensions>
BCJ-FPLVA
BCJ-FPLV01
BCJ-FPLHA
Mutichannel Systems
<Panel Hole Dimensions>
BCJ-FPLVA*
BCJ-FPLV01*
BCJ-FPLV-L*
2.5 2 3 0.5
27
∅ 14
BCJ-RPLH
(16.17)
1.1
-30
φ8.4
φ14
BCJ-FPLV-L
Connectors
751 BNC, 751 N
BNC Dust Caps
Model
Description
BCJ-DC
Polyethylene (Black)
BCJ-DC-CH
Polyethylene (Black) with string
BCJ-DC
•Standard package (20pcs/100pcs)
● Protects unused BNC receptacles from dirt and dust.
BNC - RCA Adapter
Model
Description
BCP-RCAJ
RCA Jack (F) to BNC Plug (M)
BCJ-RCAP
BNC Jack (F) to RCA Plug (M)
BCP-RCAJ
•Standard package (1pc)
● Gold plated center contact
● Secure finger grip and reliable mating
BCJ-RCAP
NCP-H8HD
Suitable Cable
∅ 23
Model
∅ 21
751 N Solder Plug
L-8CHD
(50)
NCP-H8HD
•Standard package (1pc)
● Gold plating on the contact pin prevents deterioration, even after years of
use.
● 1.1 or less VSWR up to 2GHz. <Fig. 3>
● Solder type
Return loss
(dB)
0
VSWR
SMPTE424M
-10
1.3
1.2
-20
1.1
-30
-40
Tools required: 17mm and 21mm wrenches
-50
0
1.5
3.0
(GHz)
Fig.3 Return loss for NCP-H8HD
H9.5
Caution: The connecting section of the N connector uses a shape that conforms to the
IEC169-16’s 751 impedance standard. Note that the 501 N and other connectors
that do not conform to this specification cannot be connected.
Description
∅ 18
Model
NCJ-BCJR
∅ 14.9
751 N to BNC Adapter
7/16-28 UNEF-2A max6
N (F) - BNC (F)
5/8-24 UNEF-2A
NCJ-BCJR
● Beryllium copper (gold plated) is used on the center contact for its
superior spring characteristics.
● 1.1 or less VSWR up to 2GHz. <Fig. 4>
● Panel mountable as well. For isolation from the panel, use Canare
isolation bushing IU-7/16.(See page 29)
Return loss
(dB)
0
VSWR
SMPTE424M
-10
HEX14
1.1
-40
0
1.5
3.0
(GHz)
Fig.4 Return loss for NCJ-BCJR
Connectors
12.5
39
-30
-50
32
20.9
1.3
1.2
-20
∅ 11.2
•Standard package (1pc)
9.6
Panel Hole Dimensions
751 Triaxial Connectors
Key Features and Benefits
● True 751, DC 1.5GHz; *20dB return loss ()1.2 VSWR)
● Push-lock mechanism
- no cable stress when detaching to prevent cable break
● Reliable crimp system
● Rugged and durable construction
Fiber-Optic Systems
751 Triaxial Connectors
Canare CC series cover global triaxial interconnection. CC-F series are ideal for interconnecting European triax system
and CC-K series for American triax system.
CC-F Series
Cable compatibility meets European interconnecting requirements.
Description
CCF5-JFC
CCM5-PFC
CCF5-JFRC
CCM5-PFRC
CCF7-JFC
CCM7-PFC
CCF7-JFRC
CCM7-PFRC
Canare
Crimp type, Female cable mount
Crimp type, Male cable mount
Crimp type, Female panel mount
Crimp type, Male panel mount
Crimp type, Female cable mount
Crimp type, Male cable mount
Crimp type, Female panel mount
Crimp type, Male panel mount
Suitable Cable
Others
Belden: 7783A
L-5CFTX Klotz: TRIAX8
Fujikura: 4.8/1.0 EFTXF
Belden: 7784AS
L-7CFTX Klotz: TRIAX11
Fujikura: SUPERFLEX11
Center
contact
BN9194
BN1135
BN9194
BN1135
BN9182A
BN1131
BN9182A
BN1131
Boot/Cap
CB31
CB32
DCF02
DCM02
CB31
CB32
DCF02
DCM02
Sleeve A
Sleeve B
BN7120
BN7120
BN7120
BN7120
BN7113
BN7113
BN7113
BN7113
BN7121
BN7121
BN7121
BN7121
BN7114
BN7114
BN7114
BN7114
Crimp Tool
TC-1
+
TCD-65C
Connectors
Model
TC-2
+
TCD-96C
(80.8)
37.5
2.5
CANARE
∅ 36
37.5
CANARE
69.3
Cables
∅ 23.5
76
CCF7-JFC
CCM7-PFRC
37.5
Sleeve A
Sleeve B
CANARE
∅ 23.5
37.5
CANARE
∅ 24
Center Contact
(76)
56.3
2.5
78
(VSWR)
1.50
1.45
CCM7-PFC
CCF7-JFRC
1.40
∅ 32
(90)
3.
∅
1.25
31
120
1.20
DCF02
∅
3.
31
7
(90)
29
1.15
∅ 32
∅
CB31
∅3
24.5
.5
24.5
∅ 32
1.30
1.10
∅ 32
27.5
1.05
27.5
500MHz
1GHz
1.5GHz
1.00
2GHz
140
CB32
Panel Hole Dimensions
DCM02
VSWR for CCx7-F
Model
Description
CCF4-JK
CCM4-PK
CCF4-JKR
CCM4-PKR
Crimp type, Female cable mount
Crimp type, Male cable mount
Crimp type, Female panel mount
Crimp type, Male panel mount
Retrofit Kit
Boot/Cap
Crimp Tool
BN9127A
BN9128B
BN9127A
BN9128B
CB23
CB22
DCM02
DCM03
TC-1 + TCD-316C
Belden: 1856A, 1857A, 9267
Gepco: LVT61859, VT61859
L-4CFTX
78.7
37.5
(78.7)
Suitable Cable
Others
Canare
2.5
18.7
(VSWR)
1.50
CANARE
∅ 28
37.5
CANARE
∅ 28.4
31
.5
∅3
1.40
1.35
∅
77.2
37.5
77.2
31
1.30
31
CCF4-JKR
1.25
18.7
2.5
31
1.20
18.7
CANARE
∅ 29.9
∅ 37
37.5
CANARE
∅ 28.6
1.15
Panel Hole Dimensions
1.10
1.05
500MHz
1GHz
1.5GHz
1.00
2GHz
CCM4-PKR
VSWR for CCx4-K
Connectors
33
Cable Assemblies
1.45
CCF4-JK
Mutichannel Systems
CC-K Series
Cable compatibility meets American interconnecting requirements.
CCM4-PK
Panels & Patchbays
7
1.35
Connectors
RCA Connectors
RCA Pin Connectors
■ RCAP-C Series (Crimp Plugs)
Suitable Cable
Model
Canare
RCAP-C25F
RCAP-C25HD
RCAP-C3A
RCAP-C3GS
RCAP-C3F
RCAP-C42
RCAP-C4A
L-2.5CFB
L-2.5CHD
L-3C2VS, L-3C2V, V*-3C
GS-6
L-3CFB, V*-3CFB
—
LV-61S
RCAP-C4F
L-4CFB, V*-4CFB
RCAP-C53
RCAP-C5A
RCAP-C5F
RCAP-C77
L-4.5CHD
L-5C2VS, L-5C2V, V*-5C
L-5CFB, V*-5CFB
LV-77S
Others
1855A, 8218, 1417B, 1418B
—
—
—
—
1505F
8241, 8279, RG-59B/U
1505A, 1505ANH, 8212, 8241F, 9167,
9259, 9659
1694A, 9066, 9116, 9118, 9248
—
—
8281F
Center Pin
Sleeve
Boot
Die Set
B11014E
B11015E
B11014E
BN1093
B11015E
B11016E
B11015E
BN7029C
BN7129
BN7003A
BN7079
BN7003A
BN7011
BN7015A
—
—
CB24
CB25
CB24
—
CB25
TCD-35CA
TCD-35CA
TCD-35CA
TCD-35D
TCD-35CA
TCD-31C
TCD-4CA, TCD-451CA
B11016E
BN7015A
CB25
TCD-4CA, TCD-451CA
B11020D
B11016E
B11020D
B11016E
BN7016
BN7016
B75004A
B75004A
CB26
CB26
CB26
CB26
TCD-35CA
TCD-35CA
TCD-5CF, TCD-55FA
TCD-5CF, TCD-55FA
•Standard package (20pcs/100pcs)
● Canare crimp design ensures quick and reliable installation.
● The crimp tool for the RCAP-C can be used for the Canare crimp BNC
plugs as well, thus saving on extra equipment.
Be sure to use the Canare crimping tool for installing connectors on cables.
RCAP-C3A
RCAP
C3
■ Solder Plugs
Model
Description
Plug
Plug (long sleeve)
F-09
F-10
F
F-09
ķŮŢŹ
ЋIJĴ
•Standard package (10 pcs)
● Robust metal shell
● Comfortable grip
● Cable OD up to 6.0 mm.
F
10
F-10
ĸįĶ
ijijįĹ
ĴĶįķ
RJ-JR
■ Standoff Receptacle
Description
Jack to Jack
ЋIJĺįĵij
Model
RJ-JR
•Standard package: 20 pcs by insulation color
RJ JR
RJ-JR
ijĺ
ijįĵ
● Insulation color is available in 5 colors (red, green, blue, yellow, white).
● VSWR 1.2 @ 100Mhz
RJ-RU
RCA - RCA
ЋijĴ
ĴIJ
RJ-RU
ijĮ
ijķ
RJ-JRUD
RJ-JRUD
ЋIJĺįĵij
● Three types of flanges are available.
● Insulation color is available in 5 colors (red, green, blue, yellow, white).
● VSWR 1.2 @ 100Mhz
<Panel Hole Dimensions>
ITT XLR-F77 Flange
įĵ
IJĺ
Neutrik D (Black)
•Standard package: 20 pcs by insulation color
RJ-JR (*)
ЋĴ
Ĵįķ
RCA - BNC
ijįĸ
ĵįĸ
ijĵ
RCA - Solder
Flange Type
ITT XLR-F77
Neutrik D
Neutrik D (Black)
ITT XLR-F77
Neutrik D
Neutrik D (Black)
ITT XLR-F77
Neutrik D
ĴIJ
Description
Ћij
Model
RJ-RU
RJ-RUD
RJ-RUDB
RJ-JRU
RJ-JRUD
RJ-JRUDB
RJ-BCJRU
RJ-BCJRUD
RJ-BCJRUDB
ЋijIJįĵ
■ Flush-mount Receptacles
Neutrik D Flange
ijįĵ
ĴIJįĵ
2−∅ 3.4
ijĮЋĴ
ijĴ
Ĵı
.6
23
24
∅
Ћij
IJȾ
ıį
ij
19
RJ-BCJRU
(*) RJ-JR accepts insulation bushing IU-7/16; in this case, panel hole for IU-7/16 should be
adopted (see page 29)
34
Connectors
IJĹ
ijĶ
RJ-BCJRU
F Connectors, Phone Plugs
■ FP-C Series (Crimp Plugs)
Suitable Cable
Model
FP-C25HD
FP-C3
FP-C31
FP-C3F
FP-C4
FP-C4F
FP-C5
FP-C52
FP-C53A
FP-C55A
FP-C5F
FP-C71A
FP-C7FA
Others
—
—
—
—
8241, 8279, RG-59B/U
1505A, 1505ANH, 8212, 8241F, 9167, 9259, 9659
—
—
1694A, 9066, 9116, 9118, 9248
1695A, 89120, 87120, 633948, 9116P
—
7731A, 9064, 9292, 1617A, 9011
—
Center Pin
Sleeve
Boot
Die Set
BN1003B
BN1002B
BN1002B
BN1003B
BN1003B
BN1004B
BN1004B
BN1004B
BN1005B
BN1005B
BN1005B
BN1041A
BN1030A
BN7129
BN7003A
BN7011
BN7003A
BN7015A
BN7015A
BN7016
BN7014
BN7046
BN7045A
B75004A
BN7021A
BN7021A
—
CB24
CB25
CB24
CB25
CB25
CB26
—
CB26
—
CB26
—
—
TCD-35CA
TCD-35CA
TCD-31C
TCD-35CA
TCD-4CA, TCD-451CA
TCD-4CA, TCD-451CA
TCD-35CA
TCD-451CA
TCD-35CA
TCD-35CA
TCD-5CF, TCD-55FA
TCD-7CA
TCD-7CA
Connectors
Canare
L-2.5CHD
L-3C2VS, L-3C2V, V*-3C
L-3C2W
L-3CFB, V*-3CFB
LV-61S
L-4CFB, V*-4CFB
L-5C2VS, L-5C2V, V*-5C
L-5C2W
L-4.5CHD
—
L-5CFB, V*-5CFB
—
L-7CFB
Fiber-Optic Systems
F Connectors
This type is used in such applications as home television receivers for cable television (CATV) systems.
•Standard package (20pcs/100pcs)
● Lock mechanism improves reliability by preventing shifting or detaching
of the center pin.
● The tools and cable stripper can be used for the Canare crimp BNC plugs
as well, thus saving on extra equipment.
● VSWR of 1.1 or less up to 2GHz. Compatible with broadcast satellite (BS)
and communications satellite (CS) signals.
● Designed for indoor use.
VSWR
S11(dB)
0
SMPTE424M
-10
1.3
1.2
-20
1.1
FJ-JR
-30
-40
-50
0
1.5
Cables
FJ-FPC
FP-C4
3.0
(GHz)
Fig.1 Return loss for FJ-FPC and FJ-JR
Be sure to use the Canare crimping tool for installing connectors on cables.
■ Standoff Receptacle
Description
Jack to Jack
PC Board Straight Mount
Panels & Patchbays
Model
FJ-JR
FJ-FPC
•Standard package (20pcs/100pcs)
● VSWR of 1.1 or less up to 2GHz. Compatible with broadcast satellite (BS)
and communications satellite (CS) signals. <Fig. 1>
● For insulation from the panel, use insulation bushing IU-7/16.
(Panel thickness: 1.2~3.0mm)
Panel Mount Hole Dimensions
FJ-FPC
FJ-JR
PC Hole Dimensions
ijĮЋĴ
IJĴįĶ
FJ-JR, FJ-FPC
ijįĵ
ıįij
IJĹ
ĹįĶ
ijĶ
FJ-FPC
FJ-JRU
FJ-JRU
■ Flush-mount Receptacles
Flange Type
ITT XLR-F77
Neutrik D
Neutrik D (Black)
ijįĸ
ĵįĸ
● Three types of flanges are available.
IJIJįij
Ķ
ijĸįĵ
ijĵ
ĹįĶ
Ĵįķ
•Standard package: 20 pcs
ĴIJ
ijĮЋĴįĵ
ЋijIJįĵ
Jack to Jack
ЋijĴ
Description
Ћij
Model
FJ-JRU
FJ-JRUD
FJ-JRUDB
Ķ
ijĺįĸ
IJȾ
Mutichannel Systems
2- ∅ 1.45
9.6
Ћij
ijĴ
∅ 1.3
Ĵı
ЋIJĺįĵij
∅ 11.3
8.1
IJĺ
ijķ
FJ-JRUD
FJ-JRUD
Cable Assemblies
Phone Plugs
Model
F-11
F-12
F-15
F-16
F-11
Description
3.5mm Mini Phone TS
3.5mm Mini Phone TRS
6.3mm (1/4") TS Phone
6.3mm (1/4") TRS Phone
Canare
Phone Plugs
Single-piece construction
F-12
Round finish at the base
Others
Two-piece construction
•Standard package (10pcs)
● Featuring a properly cable cramp system ensures long life reliability.
● Suited to cables up to 6.0mm∅ in size.
F-15
F
No round finish
Canare’s durable design
Connectors
F-16
35
Connectors
501 BNC Connectors
501 BNC Crimp Plugs
VSWR of 1.1 or less up to 2GHz, 1.2 or less up to 4GHz.
■ BP-C Series
Model
BP-C3
BP-C31
BP-C4
BP-C5
BP-C5FA
BP-C51
Suitable Cable
Center Pin
Sleeve
Boot
BN1023A
BN1023A
BN1024A
BN1025B
BN1016C
BN1025B
BN7003A
BN7011A
BN7030A
BN7016A
B75004A
BN7002A
CB03
CB04
CB03
CB05A
CB05A
—
Center Pin
BN1023A
BN1025B
Sleeve
BN7011
BN7002
L-3D2V, 3D-2V
L-3D2W, 3D-2W
RG-58C/U, RG-58A/U
L-5D2V, 5D-2V
L-5DFB, 5D-FB
L-5D2W, 5D-2W
Die Set (Model: TCD-***)
55FA
35D
3151D
●
●
●
●
●
BP-C5
●
•Standard package (20pcs)
■ BP-LC Series (Right Angle Type)
Model
BP-LC31
BP-LC51
Suitable Cable
L-3D2W, 3D-2W
L-5D2W, 5D-2W
Die Set
TCD-3151D
•Standard package (20pcs)
BP
LC31
BP-LC31
● Lock mechanism used on insulation improves reliability by preventing
shifting or detaching of the contact pins.
● Elongated body design for straight type enables easy attachment and
removal.
● Gold plating on the contact pin prevents deterioration, even after years of
use.
● Use of crimping to attach the connectors ensures quick, reliable
installation.
Return loss
(dB)
0
VSWR
-10
1.3
1.2
-20
1.1
-30
-40
-50
0
2.0
4.0
(GHz)
Return loss for BP-C31
Be sure to use the Canare crimping tool for installing connectors on cables.
max 6
BJ
Model
BJ-JR
7/ 16- 28 UNEF-2A
∅ 14
501 BNC Receptacles
■ Standoff
10. 9
Description
Jack to Jack
2
20. 9
(33.8)
BJ-JR
BJ-JR
•Standard package (20pcs)
∅ 19.42
BJ -
● Mounting hole size is same as that for BCJ-R/1 connector.
■ Flush-mount Receptacles
Description
13. 5
Flange Type
ITT XLR-F77
Neutrik D
Jack to Jack
5
2. 4
10. 9
31. 42
2 -∅ 3
● Two types of flanges are available.
● Flush-mount receptacle prevents damage on the jack.
.2
±0
21
30
∅
•Standard package (20pcs)
23
Model
BJ-JRU
BJ-JRUD
BJ-JRU
BJ
JRU
18
25
BJ-JRU
∅ 14
501 BNC Extension Adapter
Description
Jack to Jack
BJ
Model
BJ-J
10. 9
10. 9
33. 8
•Standard package (20pcs)
BJ-J
BJ
J
● VSWR of 1.1 or less up to 4GHz.
BJ-J
Return loss
(dB)
0
VSWR
-10
1.3
1.2
-20
1.1
-30
-40
-50
0
2.0
Return loss for BJ-J
36
Connectors
4.0
(GHz)
501 TNC, 501 N, 501 SMA Connectors
501 TNC Crimp Plugs
Return loss
(dB)
0
Model
TNP-C3
TNP-C31
TNP-C4
TNP-C5
TNP-C51
Suitable Cable
L-3D2V, 3D-2V
L-3D2W, 3D-2W
RG-58C/U, RG-58A/U
L-5D2V, 5D-2V
L-5D2W, 5D-2W
Boot
CB03
CB04
CB03
CB05A
—
TNP-C5F
L-5DFB, 5D-FB
CB05A
Die Set
TCD-35D
TCD-3151D
Fiber-Optic Systems
■ TNP-C Series
VSWR
-10
1.3
1.2
-20
1.1
TCD-35D
-30
TCD-3151D
TCD-35DF
TCD-55FA
-40
-50
0
2.0
4.0
(GHz)
TNP-C3
•Standard package (20pcs)
Return loss for TNP-C3
■ TNP-LC Series (Right Angle Type)
Suitable Cable
L-3D2W, 3D-2W
L-5D2W, 5D-2W
Die Set
TCD-3151D
Connectors
Model
TNP-LC31
TNP-LC51
•Standard package (20pcs)
● VSWR of 1.1 or less up to 2GHz, 1.2 or less up to 4GHz.
● Use of crimping to attach the connectors ensures quick, reliable
installation.
● Crimping tool can be used for the Canare crimp BNC plugs as well, thus
saving on extra equipment.
● Elongated body design for straight type enables easy attachment and
removal.
Be sure to use the Canare crimping tool for installing connectors on cables.
NP-C51
Cables
501 N Crimp Plugs
31
Boot
CB04
—
Die Set
10
Suitable Cable
L-3D2W, 3D-2W
L-5D2W, 5D-2W
39.25
Model
NP-C31
NP-C51
∅ 21
■ NP-C Series
TCD-3151D
•Standard package (20pcs)
∅ 7.6
Suitable Cable
L-3D2W, 3D-2W
L-5D2W, 5D-2W
Die Set
Panels & Patchbays
Model
NP-LC31
NP-LC51
15
■ NP-LC Series (Right Angle Type)
∅ 5.4
∅ 10
TCD-3151D
NP-LC31
•Standard package (20pcs)
● VSWR of 1.1 or less up to 2GHz, 1.2 or less up to 4GHz.
● Lock mechanism used on insulation prevents shifting or detaching of the
contact pins.
● Use of crimping to attach the connectors ensures quick, reliable
installation.
NP-LC31
∅ 7.9
■ SMAP-C Series
6.2
8.5
Suitable Cable
1.5D-QEW
L-3DFB
L-3D2W, 3D-2W
L-5D2W, 5D-2W
SMAP-C5F
L-5DFB, 5D-FB
17.9
Die Set
TCD-1DB
TCD-35DF
∅ 4.6
Model
SMAP-C1
SMAP-C3F
SMAP-C31A
SMAP-C51
SMAP C1
SMAP-C1
Mutichannel Systems
501 SMA Crimp Plugs
∅ 3.25
Be sure to use the Canare crimping tool for installing connectors on cables.
8
TCD-3151D
TCD-35DF
TCD-55FA
SMAP-C1
•Standard package (20pcs)
L-5DFB, 5D-FB
∅5
SMAJ-C5F
Die Set
TCD-35DF
TCD-3151D
TCD-35DF
TCD-55FA
6.35
∅ 9.2
Suitable Cable
L-3DFB
L-5D2W, 5D-2W
7.5
31.1
SMAP-C31A
∅ 6.7
Model
SMAJ-C3F
SMAJ-C51
Cable Assemblies
■ SMAJ-C Series
•Standard package (20pcs)
● Center contact for SMAP-C1 is of solder type.
● VSWR of 1.1 or less up to 2GHz, 1.2 or less up to 4GHz.
(SMAP-C1: VSWR of 1.2 or less up to 2GHz.)
15
SMAJ-C3F
Be sure to use the Canare crimping tool for installing connectors on cables.
SMAJ-C3F
Connectors
37
Connectors
Cable Stripper, Crimp Tools
Coaxial Cable Stripper
Three internal circular steel blades perform precise, extremely clean andd
easy stripping.
Model
Preset to
TS100E
LV-77S·L-5CFB, V*-5CFB, V*-5C, LV-61S·L-4CFB, V*-3C
TS100U
L-2.5CHD, 1855A, 1505A, 1694A
● For most Canare BNC, DIN, RCA and F crimp plugs.
● Rotary knob to select 5 different cable setups.
● Make your own cable setting within cable O.D. 4mm~11mm
● Hex wrench is attached on the lid top for quick adjustment.
● One replacement blade included, and also sold separately.
Replacement blade: TSC (1pc)
TS100E
Note:
The following types of cables may not be accurately processed by
Canare’s TS100 Cable Stripper, owing to their construction.
1. Cables employing such hard jacket material as polyethylene.
2. Cables employing such particularly soft insulator material as highfoam polyethylene.
3. Cables employing steel wire and semirigid pipe for outer conductor.
Turn cam knob to the right cable
selection.
Straighten cable and insert into
handle grip.
(mm)
Close lid, firmly grasp handle grip, and
slowly rotate 7-10 times.
Push open lid, pull cable while firmly
pressing yellow flag lever.
Insulation and jacket will be easily
peeled off.
Crimp Tools
Canare crimp tool offers reliable high-quality crimping performance in an easy-to-use design.
■ Die Sets
■ Hand Crimp Tools
Model
TCD-1DB
TCD-31C
TCD-3151D
TCD-316C
TCD-35CA
TCD-35D
TCD-35DF
TCD-4CA
TCD-451CA
TCD-55FA
TCD-5CF
TCD-5HD
TCD-65C
TCD-67HD
TCD-7CA
TCD-96C
TCD-D253F
TCD-D534F
■ Accessories
Model
Model
TB-2A
BET-12
BET-MBNC
BET-DIN
Description
Tool case
Extraction tool for BNC straight plug
Extraction tool for MBCP-C series
Insertion / extraction tool for DCP-C series
Length
—
12 inch
30 cm
30 cm
TC-1
TC-2
TC-1
● Select the appropriate die set to suit the individual connector
● Hand crimp tool is required for die set, and sold separately
● Die set are interchangeable
TB-2A
(tools and connectors not included)
For crimp sleeves
BET-DIN
TC-1
BET-12
For center contacts
BET-MBNC
MB
38
Connectors
Crimp Tools
Crimp Connector Assembly Instructions
9
Crimp sleeve
19
Jacket
(mm)
Stage
Whisker
Cutting chips
Aluminum wrapping tape
Center contact pin
Crimp
Check crimp height
Correct crimp position
Gap
Poor crimp position
Crimp
4. Slide crimp sleeve up against connector body over the braided
shield until it butts against the connector body. Center the die over
the crimp sleeve and crimp in place, using the specified crimp tool
and die set.
• Do not pull the cable while crimping is executed.
F A O
3. Tool Measuring
Procedures
Crimp force increases
and crimp height
decreases when the
tool’s adjuster dial is
turned in the direction
of the 9. The dial
is adjusted by first
releasing it using a
screw driver.
The actual contact surfaces on Canare’s BNC connectors are designed in
conformance with JIS standards and therefore pose no compatibility problems.
Q Does it matter in which direction crimp sleeves are attached?
Canare BCP plug
A For BCP-A3–use and other non-stepped (straight type) crimp sleeves, it does not
matter in which direction the crimp sleeve is attached. The attachment direction
also does not matter for BCP-A5F–use and other specific-use types that have a
chamfer (groove) at one end of the crimp sleeve.
MIL
Mutichannel Systems
However, stepped crimp sleeves such as those for BCP-C1, etc. are directional
and must be attached in the direction shown in the diagram below, with the cable
threaded through the sleeve starting from the end with the step (that is, the end
with smaller-diameter hole).
Crimp height value= (A+B) /2
Refer to the separately included manual for the appropriate
crimp height values for individual connectors.
Panels & Patchbays
Die-chamfered side
3. Hold the cable and push it into the connector body until the center
contact is locked in place. You may feel a click sound when the
center contact pin is locked.
• Pull the cable gently (less than 4.5lbs or 19.6N) to confirm that
is locked.
2. Measuring Frequency
Crimp height is measured prior to commencing use
of the crimp tool and always when changing the
crimping die. After this, the crimp height is regularly
measured after about each 1,000 crimps.
Cables
Example of installation using BNC
2. Place the center contact pin of the connector on the inner
conductor of the cable and crimp the center contact pin at the
correct position (without remaining a gap) as shown at left, using
the specified crimp tool and die set.
• To confirm the crimping properly, measure the crimp height
after removing burrs with a knife. If it is not within the ideal
value range, adjust the crimp tool.
• Do not crimp the center contact pin at the stepped root end.
• Confirm the center contact pin is crimped straight to the inner
conductor. If the center contact pin is slanted, align it gently.
1. Measuring Crimping height
Crimp height is measured after the crimp is made.
As shown in the figure, the sum of the measured
values for both directions is divided by two to arrive
at the crimp height. The ideal value range for the
BCP-A3 connector, for example, is 1.4mm to 1.5mm.
When this value is lower (overcrimping occurs) than
the recommended crimp height, the crimp becomes
very hard. A value higher (undercrimping occurs)
than the recommended value can result in increased
electrical resistance and a physically weaker crimp.
Either digital calipers or a micrometer should be used
for measuring crimp height.
Connectors
3.5
Confirm compatibility of the connector and cable prior to assembly.
1. Slide the crimp sleeve over the cable and strip the jacket, braided
shield, and insulation of the coaxial cable as shown at left.
• For cables with stranded inner conductor, twist the strands in
the same direction as plied after removing the insulation.
• For a crimp sleeve with steps, slip it over the cable from the
stepped end, as in the diagram.
• If any aluminum foil shield is left on the cable, it may get stuck
in the mouth of connector, making insertion impossible.
• Remove all stray strands and offcuts of the aluminum foil shield
to avoid possible short circuiting.
• Make sure the inner conductor is free of all insulation debris
and offcuts to ensure complete crimping.
Fiber-Optic Systems
Inner conductor
Insulator
Outer conductor
(braided)
Part A
Adjusting Crimp Tool
JIS
Q Is it possible to use cables not listed in the connector compatibility table as long as
they are close to the dimensions of those listed?
A No. While connection may be possible, performance may be adversely affected.
Q What should be done with an aluminum foil shield?
A Strip the aluminum foil shield to the root of the braided shield (to the edge of the
jacket).
Q Why do some BNC plugs made by other companies have a sharp point at the tip of
the central contact? Are these compatible with Canare’s BNC receptacles?
A The central contact is pointed in conformance with the JIS standard for 501 BNC
connectors. The central contacts on Canare’s connectors conform to the MIL
standard, and therefore are not pointed. These two different shapes simply offer
different ways to guide the plug into the female receptacle and have no direct
effect on contact quality.
Therefore, it is necessary to test and evaluate whether it is actually possible to use
the configuration in question. Particular caution should be used when crimping is
involved.
Q What is meant by “cable contact strength”?
Cable Assemblies
If any aluminum foil shield is left on the cable, it may get stuck in the mouth of
connector, making insertion impossible.
Even if the connection appears to work, factors such as electrical instability, weak
cable contact strength and others may cause problems during actual use.
A Cable contact strength refers to the maximum load borne by the cable when
exerting tensile force to remove it from the connector. For Canare products, “cable
contact strength” refers to the contact strength of a cable’s outer conductor, not
including the pull-out strength of the central contact or the contact strength of the
inner conductor.
Q What is the approximate insertion loss associated with connectors?
A The value varies depending on the connector, but for BNC plugs the value is
approximately 0.1dB per plug (DC–2GHz).
Connectors
39
Connectors
Crimp Tools
Cables to Connector Cross-Reference
■ BNC, F, RCA, etc.
See page 39, for more information about the crimp height.
BNC
Model
BCP-B
BCP-A
Crimp Plug
BCP-C
MBCP-C
BCP-LC
Solder Plug
BCP-H
Jack
F
RCA
FP-C
RCAP-C
Others
Suitable
Die Set
(*1)
Crimp
Height
TCD-1DB
—
L-1.5C2VS/V*-1.5C
L-2.5C2V
L-2.5CFB
1855A
BCP-B26
1855P
L-2.5CHD/L-2.5CHLT
BCP-B25HD
VDM230
1855ENH
BCP-B28
HD PRO 0.6/2.8 AF
1506A
L-3C2V/L-3C2VS
BCP-A25
BCP-A25F
BCP-B3F
V*-3CFB
1695A
VSD2001TS
L-3C2W
L-3CFW
BCP-B31F
V*-3CFW
LV-61S
RG-59B/U
L-4CFB/V*-4CFB
1505A, 1505ANH
HD PRO 0.8/3.7 AF BCP-B4F
VPM2000
L-4CHD
1505F
L-4.5CHD
BCP-B53
1694A
HD PRO 1.0/4.8 AF BCP-B56
BCP-B45HW
L-4.5CHWS
RCAP-C25F
FP-C25HD RCAP-C25HD
BCP-A32
BCP-H3B
BCP-H5/1
MBCP-C3F
BCP-LC3F
FP-C3F
RCAP-C3F
FP-C31
BCP-A4
MBCP-C4
BCJ-C4
MBCP-C4F
TCD-31C
VWP-C4A
MVP-C4
FP-C4
RCAP-C4A
FP-C4F
RCAP-C4F
TCD-4CA
or
TCD-451CA
RCAP-C42
TCD-31C
BCP-A42
MBCP-C53
FP-C53A
BCP-LC5
BCP-H45HW
BCP-H5B
BCP-H5/1
RCAP-C53
TCD-35CA
FP-C5
RCAP-C5A
RCAP-C77
BCP-A5F
(*2)
MBCP-C5F
BCP-LC5F
BCP-H5B
BCP-H5/1
BCP-H51F
FP-C5F
TCD-5CF
or
TCD-55FA
excluding
BCP-A5F (*2)
RCAP-C5F
BCP-H51F
BCP-B51F
BCP-A77
BCP-A52
RCAP-C77
FP-C52
BCP-C5HD
BCP-C6HD
BCP-C7HD
BCP-C7FA
1.90 - 2.00
TCD-67HD
2.15 - 2.25
TCD-7CA
1.90 -2.00
—
TCD-35D
—
2.01 -2.20
FP-C71A
NCP-H8HD
RCAP-C3GS
*1: Die set is not required for BCP-H series and NCP-H8HD *2: Suitable die set for BCP-A5F is TCD-35CA
See page 36-37, for 50 ohm cables and connectors.
4K-DIN
MD
MDM-V4C25HW
MDF-V4C25HW
V4-2.5CHW
TCD-451CA
TCD-5HD
FP-C7FA
BCP-C71A
DIN
DCP-C
1.40 -1.50
BCP-A4F
L-2.5CHD/L-2.5CHLT
DCP-C25HD
1855A
VDM230
40
BCP-H3B
BCP-H5/1
FP-C55A
■ DIN 1.0/2.3, 4K-DIN
L-3CFB
L-4CFB
1505A
VPM2000
L-4.5CHD
1694A
VSD2001
RCAP-C3A
BCP-H31F
BCP-A5
BCP-VA5
BCP-A77
Model
TCD-35CA
MCM-V5C3
MCF-V5C3
BCP-A31
V*-5C
BCP-B5F
FP-C3
BCP-A55
BCP-A5
LV-77S
MCM-V5C3
MCF-V5C3
BCP-LC3
BCP-A3F
L-5C2V/L-5C2VS
V*-5CFB
L-5CFW
V*-5CFW
8281F
L-5C2W
L-5CHD
L-6CHD
L-7CHD
L-7CFB
7731A
9292
L-8CHD
GS-6
MBCP-C25F
BCP-A3
BCP-VA3
V5-3C
L-5CFB
1.40 - 1.47
BCP-A3
V3-3C/V4-3C
L-3CFB
BCJFC1(-7/16)
BCJ-RUC1
BCP-C1
1.5C-2V
Suitable
Die Set
Crimp
height
TCD-D253F
1.08 -1.16
TCD-D534F
1.25 - 1.33
Belden: 1505A, 1505ANH, 1505F, 1506A, 1694A, 1695A, 1855A, 1855ENH, 1855P, 7731A, 8281F, 9292
Draka: HD PRO 0.6/2.8 AF, HD PRO 0.8/3.7 AF, HD PRO 1.0/4.8 AF
Gepco: VDM230, VPM2000, VSD2001, VSD2001TS
DCP-C3F
DCP-C4F
DCP-C53
Note: Be sure to use the right combination of cable, connector and die set for proper connection
Connectors
Impedance Transformers
■ Adapter Type
Model
BCJ-XJ-TRC
XLR3 (F) - BNC Jack
Description
BCJ-XP-TRC
XLR3 (M) - BNC Jack
BCJ-XJ-A10TRC
XLR3 (F) - BNC Jack, 10dB Attenuation Pad
BCJ-XJ-TRC
Fiber-Optic Systems
1101-751 Impedance Transformers
Passively convert AES/EBU digital audio signals from 1101/XLR3 output to a 751 BNC coaxial cable and then back
again to a 1101/XLR3 input.
■ Panel Mount Type
Model
XJ3F-TRC-BCJ
Description (Front - Back)
XLR3 (F) - BNC Jack
Flange Type
XJ3M-TRC-BCJ
XLR3 (M) - BNC Jack
BCJ-TRC-XP3F
BNC Jack - XLR (F)
BCJ-TRC-XP3M
BNC Jack - XLR (M)
XJ3F-A10TRC-BCJ
XLR3 (F) - BNC Jack, 10dB Attenuation Pad
BCJ-A10TRC-XP3F
BNC Jack - XLR3 (F), 10dB Attenuation Pad
ITT XLR-F77
BCJ-XJ-A10TRC
● SMPTE 276M and AES3 transmission standards
● Coaxial transmission of 2 channel digital audio
● Allows longer cable runs than 110 ohm twisted pair
● AES/EBU signal distribution using Canare 75 ohm video patchbays
Cables
BCJ-XJ-TRC / BCJ-XP-TRC
75Ω BNC (unbalanced)
Connectors
BCJ-XP-TRC
XJ3F-TRC-BCJ
110Ω XLR3 (balanced)
2 0.47 μF
TRANSFORMER
3
1
BCJ-TRC-XP3M
Panels & Patchbays
Pin 1: Shell
Pin 2: Hot
Pin 3: Cold
BCJ-XJ-A10TRC
75Ω BNC (unbalanced)
110Ω XLR3 (balanced)
2 0.47 μF
TRANSFORMER
10dB
PAD
3
1
1101-751 Impedance Transformer: Input/Output Level Performance
9.0
10.0
1.60
2.39
3.18
3.60
3.98
4.78
5.58
6.38
AES/EBU
Transmitter
(V)
2.0
3.0
4.0
4.5
5.0
6.0
7.0
8.0
Transformer Out
-10dB Pad
(V)
0.50
0.75
1.01
1.13
1.26
1.51
1.76
2.02
7.18
7.98
9.0
10.0
2.27
2.52
Transformer Out
(V)
BCJ-XJ-TRC/BCJ-XP-TRC
Panel Hole Dimensions
Cable Assemblies
AES/EBU
Transmitter
(V)
2.0
3.0
4.0
4.5
5.0
6.0
7.0
8.0
Mutichannel Systems
Pin 1: Shell
Pin 2: Hot
Pin 3: Cold
BCJ-XJ-A10TRC
Connectors
41