SWFcontract Drapery Hardware Specification Guide

Transcription

SWFcontract
Drapery Hardware
Specification Guide
GRABER DRAPERY HARDWARE
TABLE OF CONTENTS
®
Pleating Systems...................................................................... 4
Stack Pleat, Roll Pleat, Pinch Pleat
Contrack® Drapery Hardware.......................................................... 5
Overview
Made-to-Measure Rods................................................................... 6
9-804 Cord Draw
9-808 Hand or Baton Draw
9-8191/9-8091 Baton Draw
Super Duty Slimline Drapery Hardware........................................... 9
Super Duty Slimline Series....................................................... 10-11
9-650 Cord Draw & 9-657 Baton Draw
Made-to-Measure Rods................................................................. 12
9-200 Track Series
Made-to-Measure Rods................................................................. 13
9-300 Track Series
Cut-to-Measure Rods.................................................................... 14
9-400 Oval Rodding
Cut-to-Measure Rods.................................................................... 15
9-600 Solid Steel rodding
3
Call 800-327-9798 or email architectsolutions@swfcontract.com swfcontract.com
GRABER PLEATING SYSTEMS
®
Stack Pleat
Designed for maximum glass exposure when draperies are open, stack pleat
requires half the space of conventional pleated draperies. The snap tape
attachment system reduces installation time and simplifies maintenance. Snaps
detach with 4 lb. “peel" action and release with 22 lb. “shear" pull. Front and
back pleating eliminates bulky appearance. For drapery up to 54" in length,
7½" tape is recommended; 8½" tape is recommended on draperies over 54".
Use Graber Slimline or Super Duty architectural drapery hardware, cord or
baton draw systems.
Roll Pleat
The roll pleat system affords a soft, rounded pleating pattern. Widely used in
hospitality and healthcare applications where a residential appearance is desired.
A 7/8" nylon snap tape with 4¼" on center snaps is sewn into the header suspended
directly under the track to prevent sagging and tipping. Spaced carriers (rolling
or sliding) are used to control drapery fullness. Draperies snap off track easily for
cleaning and maintenance. Use Graber Slimline or Super Duty architectural drapery
hardware, cord or baton draw systems.
Pinch Pleat
Designed to provide an elegant, sophisticated look, the pinch pleat header is well
suited for either custom or ready made commercial drapery applications. Pinch
pleating is compatible with Graber Contrack and Slimline architectural drapery
hardware and adjustable traverse rods.
4
GRABER CONTRACK DRAPERY HARDWARE
®
®
The most versatile aluminum pinch pleat system in today’s market. Graber Contrack sets the standard in
heavy duty aluminum drapery hardware tracks for pinch pleat drapery. Rolling and sliding carriers are forward canted for
erect headings. Available in a variety of systems with ball bearing carriers. Graber Contrack can offer the widest range of
applications to fit any heavy duty situation.
Contrack Drapery Hardware Selections and Performance Data
(TW = Two-way, OW = One-way, Mult. = Multiple Draw)
Track # and
Traverse
Material
9-804 Cord
15/16"
15/16"
1 1/4"
1-1/4"
9-808
Hand/Baton
7/8"
7/8"
11/16"
11/16"
Mounting Applications
Max. Fabric Weight
Extruded 6063-T5
Anodized SatinFinish Aluminum
Aluminum
Association
Specification
No. AA-C22A21
Aluminum thickness
.050”
TW draw - 210 lb.
OW draw - 140 lb.
Mult. draw - 420 lb.
Extruded 6063-T5
Anodized SatinFinish Aluminum
Aluminum
Association
Specification
No. AA-C22A21
Aluminum thickness
.050”
TW draw - 240 lb.
OW draw - 120 lb.
Brackets
Max. Track Length
Bending Limits
Space brackets
48” apart except
at ends - then 24”
and 48” apart
over balance. Wall
mount projection
for 3” plus ceiling
mount available.
TW draw - 42’
OW draw - 28’
Mult. draw - 84’
Track punched 16”
on center for direct
to ceiling mount
with screws.
TW draw - 48’
OW draw - 24’
Snap-in ceiling clips
are available for
ceiling mount. Track
can also be drilled
in field for direct
screw mount. For
wall mount, space
brackets 48” apart
except at ends then 24" and 48"
apart over balance.
Projections from
3½" to 4-1/4".
TW draw - 48’
OW draw - 24’
Continuous curve or
any angle bend on 12”
radius - maximum 90˚.
No reverse curve.
5 lb./ft. rating
12” radius regular and
reverse curves, can be
continuously curved.
5 lb./ft. rating
9-8191/9-8091*
Hand/Baton
1 3/8
3/8""
1
7/8"
7/8"
11/16"
11/16"
Extruded 6063-T5
Aluminum in White
Painted Finish
Aluminum
Association
Specification
No. AA-C22A21
Aluminum thickness
.050”
TW draw - 240 lb.
OW draw - 120 lb.
5 lb./ft. rating
Can be bent to any
angle on 12” radius,
maximum 90˚. No
continuous or reverse
curves.
All systems are for conventional pinch pleat draperies. Custom painting available upon request.
*Aluminum silver finish 9-8091 is available as a special order with a minimum quantity of 2500 ft.
5
GRABER CORD TRAVERSE
CONTRACK SERIES
®
®
9-804 Heavy duty, wall or ceiling mount,
cord traverse, pinch pleat
15/16"
1 1/4"
Carriers and cord operate in separate channels for
smooth, heavy duty operability. 9-804 can be mounted
to the wall using heavy duty aluminum brackets. Ceiling
mount brackets are also available.
Specifications
1.Track: furnish and install, as indicated on plans, Graber
Contrack 9-804 extruded .050" thick dual channel
anodized satin-finish aluminum drapery track in
accordance with AA Specification C22A21.
2a. Components: For two-way draw, specify:
9-819 ball bearing masters
9-823 ball bearing pulley sets
8-648 ball bearing cord tension pulley
9-039 #5 nylon cord with fiberglass core
9-840 ball bearing master carriers
Also available:
9-849 ball bearing carrier with hook
9-861 economy slide
2b. Components: for one-way draw, specify:
9-820 reversible ball bearing master carrier
9-823 ball bearing end pulley
9-826 insert pulley
Plus track, carriers, cord and pulleys mentioned above
3.
Brackets: Specify
9-862 (3" wall mount projection)
9-865 (3" and 6" wall mount projection)
9-860 bracket for ceiling mount
Major Components
9-819
Ball Bearing Master
Carrier of 9-804
9-840 Ball Bearing Carrier
9-849 Ball bearing Carrier w/hook
9-861 Economy Slide
All are compatible with 9-804, 9-808
& 9-8191/9-8091
9-823
Ball Bearing Pulley Set
for 9-804
9-856
Splice for 9-804
9-826
Ball Bearing Insert
Pulley for 9-804
9-860
Ceiling Bracket for 9-804
8-648
Metal Cord Tension
Pulley Ball Bearing
9-862
Heavy Duty Wall Bracket
3" projection
9-865
Heavy Duty Double Bracket
3" and 6" projection
6
GRABER HAND TRAVERSE
CONTRACK SERIES
®
®
9-808 Hand draw, ceiling mount, pinch pleat
9-808 is the perfect choice for recess applications and
tight curves both regular and reverse. Ball bearing carriers
and economy slide carriers are available. (Mounting holes
punched 16" on center for ceiling installation).
Specifications
1.Track: Furnish and install, as indicated on plans.
Graber Contrack 9-808 extruded .050" thick anodized
satin-finish aluminum drapery track in accordance with
AA Specification C22A21.
9-821 ball bearing master carriers (pair)
8-637-1 (33") fiberglass batons
9-840 ball bearing carriers
9-165 end stops
Also available as options:
9-861 economy slide
9-171 left and 9-170 right return extenders
2b.Components: For one-way draw, specify: 9-822 ball
bearing reversible master carrier with baton arm, baton,
carriers and end stops mentioned above.
3.Mounting: Mounting holes punched 16" on center for
direct screw ceiling installation.
4.
For deluxe cubicle, specify:
9-808 track
9-165 end stops
Features
This heavy duty ceiling mounted track system is ideal for curved drapery applications. The 9-808 system also serves as a heavy
duty cubical track for hospital applications. Erect drapery headings are assured by the forward canted non-binding ball bearing
carriers. Perfect for recessed applications and tight curves, this track system has a durable metal baton arm.
Major Components
9-821
Ball Bearing Master Carrier two way for
9-808 & 9-8191
Fiberglass
33"
48"
60"
Baton with clip
8-637-1
8-638-1
8-639-1
9-822
Ball Bearing Master Carrier, reversible
one way for 9-808 & 9-8191
9-165
End Stop for 9-808 & 9-8191
9-710 - Right
9-171 - Left
Return Extender for 9-808 & 9-8191
9-861
9-840
9-808
9-849
9-808
Economy Slide
Ball Bearing Carrier for 9-804,
& 9-8191
Ball Bearing Carrier with hook for
9-857
Splice for 9-808
7
GRABER MADE TO MEASURE ROD
SPECIFICATIONS
®
9-8191 / 9-8091 Track Series
The most versatile aluminum pinch pleat system in today’s
market for baton draw applications, ideal for use in hotels and
healthcare. Graber Contrack sets the standard in heavy duty
aluminum drapery hardware tracks for pinch pleat drapery.
Ball bearing and slide carriers are forward canted, providing
for aesthetic fabric installation.
1 3/8"
7/8"
11/16"
9-8191 Hand draw, ceiling or wall mount, pinch pleat
9-8191 is an excellent heavy duty ceiling or wall mounted
track system. Economical and easy to install, the 9-8191 is
compatible with our snap-in ceiling bracket, or can be direct
screw mounted. Available with ball bearing wheeled carriers
or economy slide carriers, the 9-8191 comes standard in a
white painted finish. Under special order, this track is also
available in an anodized satin finish under part number
9-8091 with a minimum order quantity of 2500 ft.
Forward canted rolling carriers for
erect drapery heading
Overlapping heavy duty master
arms eliminate light gaps.
Molded end
cap cleanly
finishes end
of track.
Over the drapery baton
attachment to simplfy
drapery removal and
installation.
Baton draw Contrack® rod system
Ideally suited to upgrade drapery hardware system using
existing draperies.
Specifications
1.Track: Furnish and install, as indicated on plans, Graber
9-8191 extruded .050" thick track in a white painted
finish in accordance with AA Specification C22A21.
2b. Components: For one-way draw, specify:
9-822 ball bearing reversible master carrier with
adjustable baton arm (assembled in down position)
with baton, carriers and end stops indicated above
Also available as an option:
9-831 ball bearing master carrier with adjustable baton
arm (assembled in up position)
Brackets: For ceiling mount, specify:
9-955 snap-in ceiling bracket
Track may also be drilled in field for direct screw mount
For wall mount, specify:
9-957 wall bracket
2a. Components: for two-way draw, specify:
9-821 ball bearing master carriers with adjustable
baton arm (assembled in down position)
8-637-1 (33") fiberglass baton
9-840 ball bearing carriers
9-165 end stops
Also available as options:
9-824 ball bearing master carrier with adjustable
baton arm (assembled in up position)
9-849 ball bearing carriers with hook
9-861 economy slide
9-171 left and 9-170 right return extenders
Major Components
9-821
Ball Bearing Master Carrier two way for
9-808 & 9-8191
9-861 - Economy Slide
9-822
Ball Bearing Master Carrier, reversible
one way for 9-808 & 9-8191
8-637-1 - 33" Fiberglass Baton with clip
8-638-1 - 48" Fiberglass Baton with clip
9-165
End Stop for 9-804, 9-808 & 9-8191
9-957 - Wall Bracket
9-170 - Right
9-171 - Left
Return Extender for 9-808 & 9-8191
9-955 - Ceiling Bracket
9-840
Ball Bearing Carrier for 9-804, 9-808
& 9-8191
9-850 - Splice
8
GRABER SLIMLINE SUPER DUTY
DRAPERY HARDWARE
®
Product Features
Graber Super Duty Slimline systems offer the most diverse aluminum drapery hardware available today for the alternate
pleating systems (roll, pinch and stack pleat). Heavy duty provides the only wheeled system available for alternate
pleats. Combined, these can satisfy a wide variety of drapery hardware requirements and applications. Especially popular
for recess mounting applications and heavy drapery requirements. Super Duty Slimline can prove to be a valuable energy
and cost saver without resorting to bulky, expensive stage or special application tracks. Specify Graber Super Duty
Slimline for your snap tape drapery hardware requirements.
Super Duty Slimline Drapery Hardware Selections and Performance Data
(TW = Two-way, OW = One-way)
Track # and Traverse
9-650 Cord Traverse
Material
Anodized
aluminum in
natural or white
baked enamel.
Mounting Applications
Max. Fabric Weight
TW draw - 120 lb.
OW draw - 60 lb.
Brackets
Max. Track Length
Bending Limits
Projection from 3½"
to 4½" plus ceiling
mount.
TW draw - 48’
OW draw - 24’
Projection from 3½"
to 4½" plus ceiling
mount.
TW draw - 32’
OW draw - 16’
Track thickness
.060"
Can be continuously
curved to any angle
using 12" radius.
Reverse curving not
available.
.060" wall
2.5 lb./ft. rating
9-657 Baton Traverse
Anodized
aluminum in
natural or white
baked enamel.
TW draw - 60 lb.
OW draw - 30 lb.
Track thickness
.060"
.060" wall
Can be bent and
reverse curved to any
angle using 12" radius.
Continuous curving not
available.
2.5 lb./ft. rating
NOTE: Super Duty Slimline drapery tracks can be used with pinch pleat drapery if #9-396 horseshoe clips are used to lock the pendants (9-345) onto the
sliding or rolling carriers (two-piece snap-in carriers). One-piece sliding carriers 9-342 and 9-450 also can be used for pinch pleat draperies. Round overhead
pins (pinned at the top of the drapery) also are recommended.
9
GRABER SUPER DUTY SLIMLINE SERIES
®
9-650 Series, super duty, cord draw for roll,
stack and pinch pleat systems
Our Super Duty slimline series track systems provide
added strength for the heaviest draperies and extra wide
openings. Ball bearing end pulleys and wheeled carriers
provide a smooth cord draw operation.
Specifications
1.Furnish and install as indicated on plans,
Graber 9-650 Super Duty Slimline dual channel
.060" thick anodized aluminum track.
(for roll pleat, 100% fullness)
9-395 connected rolling swivel carrier
9-345 swivel snap pendant
2b. Components: For one-way draw, specify:
9-350 right or 9-351 left ball bearing end pulley
9-353 ball bearing one way end pulley
9-355 right or 9-354 left hand master plus tension
pulley, cord and carriers as indicated above
9-350 right and 9-351 left ball bearing end pulleys
9-355 right overlap master carrier*
9-354 left underlap master carrier*
8-648 ball bearing cord tension pulley
9-040 #4 nylon cord with fiberglass core
9-383 unconnected rolling swivel carrier
(for stack and pinch pleat)
3.Brackets: Specify:
for wall mount, 9-359 adjustable wall bracket
(3½" - 4½" projection) for ceiling mount,
9-360 ceiling bracket
*Also available: 9-357 right and 9-356 left butt masters
Major Components
9-351
End Pulley left hand
9-350
End Pulley right hand
9-358
Track Splice
9-356
Left Hand Butt Master
9-357
Right Hand Butt Master
9-360
Ceiling Bracket
9-353
End Pulley Housing
9-381 Connected Rolling Swivel
Carriers (80% fullness)
9-382 (100% fullness)
9-395 (120% fullness)
8-648
Metal Cord Tension Pulley Ball
Bearing
9-345
Swivel Snap Pendant
9-383
Rolling Carrier
9-354
Underlap Master Left Hand
9-355
Overlap Master Left Hand
9-396
Horseshoe Clip Specify for Pinch
Pleat
9-359
Adjustable Wall Bracket
10
MADE TO MEASURE ROD
SPECIFICATIONS
9-657 Series, super duty, hand (baton) draw for roll, stack and
pinch pleat systems
Like the 9-650 cord draw system, the 9-657 Super Duty Slimline
track system provides added strength and smooth operation for
the heaviest draperies, with baton draw operation.
Specifications
1.Track: Furnish and install, as indicated on plans Graber
9-657 super duty flanged channel .060" thick anodized
aluminum track. Specify finish, natural aluminum or white.
9-387 right and 9-388 left hand master carriers
9-386 end caps
9-385 return snap plate
8-637-1 (33") fiberglass baton
9-383 unconnected rolling swivel carrier
(for stack and pinch pleat)
9-345 swivel snap pendant
2b.Components: For one-way draw, specify:
9-387 right or 9-388 left master carrier plus end caps,
return plate, baton and carriers as indicated above
3. Brackets: Specify:
for wall mount, 9-379 adjustable wall bracket
(3½" - 4½" projections)
for ceiling mount, 9-391 ceiling bracket
Major Components
9-381
Swivel
9-382
9-395
Connected Rolling
Carriers (80% fullness)
(100% fullness)
(120% fullness)
9-383 - Rolling Carrier
unconnected without pendant
9-384 - Gralon Rolling Carrier
unconnected with pendant
9-345 - Swivel Snap Pendant
9-379
Adjustable Cam Bracket
9-387 - Master Carrier right
hand
9-385
Drapery Return Snap Plate
9-391 - Ceiling Bracket
9-386
End Cap Assembly
9-850 - Track Splice
8-637-1 - 33" Fiberglass
Baton with Clip
Baton with Clip
Baton with Clip
9-396 - Horseshoe Clip
9-388
Master Carrier left hand
9-404 - Double Bracket Base
(optional)
9-461-1
Snap Tape
4¼" On Center; Low Pull
Force
9-463-1 - Snap Tape
4¼" On Center; High Pull Force
11
SPECIFICATION
®
9-200 Series
Graber Made-to-Measure Tracks, Heavy Duty and Signet are
of the finest quality drapery hardware. Rolled of generous
gauge steel, durable oil-free polyester finish, ball bearing
pulleys with oversize wheels for continuous smooth operation.
Compact pulley housings for close side stacking of drapes.
9-200
Heavy Duty
White (1)
1"
A strong, versatile rodding
with a wide choice of
companion parts. Precision
formed steel rodding with
oil free polyester finish.
1/2"
One way operation: 22 lb.
Two way operation: 35 lb.
Bracket
1-7/8" - 2-7/8"
Projection 2-1/2" - 4-1/4" - standard
5" - 6-1/2"
Maximum Length 16 ft.
Specifications
9-200 Heavy Duty Series:
Furnish and install as indicated on plans, Graber 9-200 Heavy Duty Steel .0279 roll formed rodding in a white oil free
polyester finish. Includes the following components: 9-105 Adjustable Master Slides, 9-213 Ball Bearing Pulley set, 9-346
Conventional Slides, 8-655 Molded Cord Tension Pulley, 9-041 #4 nylon cord with Fiberglass Core, 9-231 Center Supports
and 9-125 End Brackets.
One-Way Left / One-Way Right 9-200 track using 9-213 Pulley Set and 9-212 End Pulley with 9-108 Master, 9-346 Slides,
9-041 #4 Traverse Cord, 8-655 Tension Pulley, 9-231 Center and End Supports, one 9-125 Bracket.
ADVANTAGES:
These sets feature ball bearing pulleys with oversize wheels and compact pulley housings for close drapery stacking, front
loading end brackets, metal adjustable master carrier arms, and spring loaded slide gate.
12
SPECIFICATIONS
®
9-300 Series
Graber Made-to-Measure Tracks, Heavy Duty and Signet are of the
finest quality drapery hardware. Rolled of generous gauge steel,
durable oil-free polyester finish, ball bearing pulleys with oversize
wheels for continuous smooth operation. Compact pulley housings
for close side stacking of drapes.
9-300
Heavy Duty
3/4"
3/8"
A popular general
purpose steel rodding for
installations of average
weight and width. Features
versatility plus economy
with a full selection of parts
and accessories. Oil free
polyester finish.
White (1)
One way operation: 20 lb.
Two way operation: 35 lb.
Bracket
1-7/8" - 2-7/8"
Projection 2-1/2" - 4-1/4" - standard
5" - 6-1/2"
Maximum Length 16 ft.
Specifications
9-300 Signet Series: Furnish and install as indicated on plans Graber 9-300 Regular Duty steel .0279" roll formed rodding in a white
oil-free polyester finish. Includes the following components: 9-310 Master Slides, 9-313 Pulley Set, 9-346 Conventional Slides, 8-655
Molded Cord Pulley, 9-042 #3¼ Nylon Cord with Fiberglass Core, 9-331 Center Support and 9-125 End Brackets.
One-Way Left / One Way Right 9-300 track using 9-313 Pulley set and 9-316 End Pulley with 9-312 Master, 9-346 Slides,
9-042 #3¼ Traverse Cord, 8-655 Tension Pulley, 9-331 Center and End Supports, one 9-125 End Bracket.
ADVANTAGES:
These sets feature nylon end pulleys with oversize wheels and compact pulley housings for close drapery stacking, spring-loaded slide
gate, front load end brackets, and metal adjustable master carrier arms.
13
GRABER CUT TO MEASURE ROD
SPECIFICATIONS
®
9-400 Oval Rodding
Graber Oval Rodding is ideal for drapery, curtain and valance
applications. The rodding is roll formed from 0.0279” thick
steel and is finished with a white polyester paint finish.
Reversible Elbows are available for a wide range of
treatments with 6 different return projections.
9-400
White (1)
9/16"
11/32"
9-415
A durable,
economical
rodding
system for
draperies and
curtains.
Available in
9 and 12 foot
lengths.
9-401-1 Reversible
9-403-1 Elbows
9-405-1
Brackets:
9-408-1
9-409-1
9-413-0
4-808-0
4-809-0
Inside bracket
Sash ¾”rojection
Push-on bracket
Single outside bracket
Double outside bracket
White (1)
Zinc Chromate (0)
Center Support:
9-419-0 Ceiling Drop
9-420-0 1-1/8" Ceiling Drop
9-421-1 Projects 2"-3"
9-423-1 Projects 3.5"-5"
9-425-1 Projects 3"-7"
9-427-1 Projects 6"-10"
White (1)
Zinc Chromate (0)
Specifications
9-400 Oval Rodding:
Furnish and install as indicated on plans. Graber 9-400 Oval Rodding roll formed from 0.0279" thick steel with an oil free white
polyester finish. For widths greater than 12 feet use splice part number 9-415-1. Choose from appropriate installation brackets and
Reversible Elbows. Elbows have the following projections; 9-401-1 (1¾” and 2¾”), 9-403-1 (3¾” and 4¾”), 9-405-1 (5¾” and
6¾”). Choose appropriate Intermediate Support Bracket based on projection.
14
GRABER CUT TO MEASURE ROD
SPECIFICATIONS
®
9-600 Solid Steel Rodding
Graber Solid Steel Rodding is designed for use with heavier
weight drapery fabric or drapes with blackout liners. They are
also an excellent choice for hanging large banner displays.
The steel rodding is ³/8” thick with a brass finish and is available
in lengths up to 12 feet.
9-600
3/8"
3/8” Solid round
rodding is strong
and versatile. Available
in 12-foot
lengths in a brass
finish. Easy to
cut to desired size.
Brass (8)
9-615-8
Outside mount
barrel bracket
with 3/8”
projection.
9-604-8
Gooseneck bracket
with 1” projection.
9-612-8
Inside mount
barrel bracket.
Specifications
9-600 Solid Steel Rodding:
Furnish and install as indicated on plans. Graber 9-600 Solid Steel Rodding, ³/8” thick with a brass finish. Select bracket for desired
installation; 9-604-8 Gooseneck Bracket with 2” projection, 9-615-8 Outside Mount Barrel Bracket with ³/8” projection or 9-612-8
Inside Mount Barrel Bracket.
15
21-5986-07 (11/12) 122497

SWFcontract Drapery Hardware Specification Guide

Transcription

Similar documents

Ball Up Sports Flyer - Holland Junior School

Throw a ball up and it will fall down 1) The force of gravity pulls the

Window Treatment Elevations and Specifications

Super 100 Large Capacity Chain Hoist (16 to 50 ton capacity)

Chart L4: Details (sidewalks, stormwater management)

Carousel Carnival Poster 2015 - Petaluma Valley Athletic Club

KRS Bearing

The Perfect Panel

Frigi-Tech - EnergyLogix Solutions Inc.

Pasadena Now » Enchanted Physics Forest Sprouting at Kidspace