Banner Clip installation ©Trussworks 10/07

Banner Clip Installation
For fabric graphics or solid fabric panel
installation onto EZ6 or EZ12 truss.
Graphics may be on either side
of a banner. The top seam will
determine which side faces you.
Rigid strips are sewn into the top and bottom ends of the banner.
Fold the top of the banner over once, so the strip is surrounded
by fabric.
Banner Clip
EZ-BNRCLP
Slide the turned edge of the banner down into the hook end of
the clip, about every two feet, then attach clips onto truss tube.
Alternately, you can attach the clips to the truss first, with the
hook end facing out, then firmly insert graphic into clip.
Your exhibit drawing shows whether to
attach the clips onto the top or bottom
truss tube.
Repeat with bottom edge, only upside down.
Small Flat Screen Mount
Instructions for mounting and installation
Works with all Trussworks systems.
Fits 75-200mm width hole pattern
Works with most plasmas & LCD’s
smaller than 40"
Mount bracket to truss, using the horizontal or vertical bracket provided for your application.
Swivel the frame so it’s facing the direction desired for your screen, and tighten top bolt to secure.
Attach crossbar and plastic spacer at choice of holes on frame, and tighten securely with wingnuts.
Mount J-clips to your monitor in the top two mounting holes using the bolts supplied by your
monitor manufacturer.
Hang J-clips onto crossbar and tighten with provided thumbscrew to secure.
Large Flat Screen Mount
Instructions for mounting and installation
Works with all Trussworks systems.
Fits 200-400mm width hole pattern
Works with most plasmas & LCD’s
37” or larger
Mount bracket to truss, using the horizontal or vertical bracket provided for your application.
Swivel the frame so it’s “feet” are facing the direction desired for your screen, and tighten top
bolt to secure.
Adjust height of crossbar at choice of hole sets on frame, and tighten securely with wingnuts.
Mount J-clips to your monitor in the top two mounting holes using the bolts supplied by your
monitor manufacturer.
Adjust crossbar extenders to the proper width for your monitor and tighten thumbscrews.
Hang J-clips onto crossbar and tighten with provided thumbscrew to secure.
Workstation Setup
Attach rear frame to side
frames with wingnuts
Stand both side frames up as shown
and insert front spacer as shown
Apply back panel to the
inside of the rear frame.
Place counter top on unit.
Be sure to alaign location pins
into lower frame.
Apply front panel by putting a
slight bend in the panel and
applying to the front of the unit.
Oval Designer Counter Setup
EZ6 Oval Designer Counter Assembly Instructions
1. Bolt 2 - A3s to the EZ6 Designer Feet using 2 carriage bolts with wingnuts for each.
2. Stand them up and install the R2s between them at top and bottom using a corner bracket
on each end.
3. Attach the counter top using the supplied brackets and wingnuts.
4. Lay the lower shelf on the lower R2 truss.
5. Install the shelf brackets at the halfway point and put the second shelf on them.
6. Magnet the graphic to the front.
3' Free Standing Counter, EZ-FSTCT3
Stand the 2 side units
apart as shown and extend
the panel frames out as shown
Attach the rear panel to
the back side of the counter
(the side with the velcro strips
top & bottom)
Bend the flaps as shown
and velcro them to the
matching velcro strips on
the counter unit, making
sure to make the seams
as invisible as possible,
also make sure that the
flaps do not interfere with
the door edges
Swivel the cross braces into
place and secure them as shown
The door has pins located
top and bottom, the pin on top
is longer than the bottom one,
to install tilt the door and insert the
top pin into the frame, then align the
bottom pin and gently
lower the door into position.
Insert the shelf
Place the counter top in position
it is held in place with velcro.
Rectangular Counter Setup
Construction Detail
EZ6 Designer Reception Counter
1. Bolt 2-A3 pieces to the EZ6 Designer Feet using two carriage bolts
with wingnuts for each.
2. Stand them up and install the A2 between them, at the bottom,
using a corner bracket on each end.
3. Attach the counter top using the supplied brackets and wingnuts.
4. Insert seambar between legs, at the front, 1/2” below the top of leg
(just under the webbing.)
Install the shelf bracket on the middle horizontal webbing, and place
the shelf on.
5. Apply 28.5"H x 24.5"W flexible graphic, using magnet strip on the
reverse perimeter.
Freestanding Counter Setup Instructions
1. Open section with top frame attached
2. Repeat with opposite side.
by folding panel frame out from body frame
3. Fold bottom down and lock into opposing 4. Fold top out and lock in place.
tabs.
5. Go to the side of the counter with velcro on the top and bottom edges. This
is the side that will have the solid panel. Velcro the solid panel into place with
the additional velcro showing on the sides.
6. Velcro the flaps to the solid panel vecro edges. Be careful to make the seams
as invisible as possible.
7. Repeat procedure on the front, this time velcroing the panels to the frame.
Be careful not to get any material beyongd the seam edge. It will interfere with
the door.
8. Install the doors with the longer pin up. Locate the holes in the frame and
insert the longer pin into hole in the underside of the top frame and then
drop in into the hole in the bottom frame.
Repeat with locking door and then velcro on the top. If you are positioning
the counter betwee 2 uprights whether as a backwall counter or in the open,
we have included 2 small tubes with velcro, you may use these by inserting
between the truss tubes and velcroing them to the counter side. This will
prevent the counter from moving separate from the truss.
Shipping Cases/Trunks
UF4825 CASE
49.5" X 27" X 12-16" OD
48" X 24" X 8-12" ID
30 lbs empty, 80-150 lbs full
(Average weight is 115 lbs)
Stackable 6 high, Rollable and UPS shippable (oversize charges may apply)
4 cases fit on a skid 50" X 48" X 54" @ about 500 lbs
Holds:
2 Packstuff Chairs & 1 Table
or 4 Slingback Chairs or Stools
or 3 Curved Back Chairs or Stools.
8 EZ6-A4
6 EZ6-R5
6 EZ6-R1
4 EZ612-A4
3 EZ12-A8
UF4848 TUB
51" X 51" X 32" OD
48" X 48" X 28" ID
Stackable 4 high, Freight shipping only
90 lbs empty, 400-600 lbs full
(Average weight is 500 lbs for EZ6, 400 lbs for EZ612 & 600 lbs for EZ12)
Holds:
32 EZ6-A4
32 EZ6-R5
24 EZ6-R1
16 EZ612-A4
14 EZ12-A8