h-1000 tub grinder

H-1000 SERIES II
[ tub grinder ]
• Grinds hay - big round bales, loose hay, small and large square bales
• Grinds crop residues - straw, stover and other types
• Grinds grain - corn (ear or shelled and high moisture), sorghum and all cereal grains
• High capacity in portable package
• Electronic governor
• Works with 80 to 175 PTO horsepower tractors
A dependable eight belt
drive system routes power
from the tractor’s PTO and
supplies it to the mill. This
drive system turns the mill at
approximately two times the
tractors PTO speed. This
higher mill speed provides
smooth feeding and delivers
high capacity grinding.
1
“BIG BITE” is the name for this
hammer mill. The mill is 44 1/2”
long and at operating speed the
hammers extend out to 26” in
diameter.
(1) The 64 swinging hammers
are arranged on eight heavy duty
hammer rods. These hammers
have four hardened cutting edges.
When the hammer’s cutting edge
becomes worn it can be replaced
by turning the hammer to the
next available fresh, sharp
cutting edge.
4
3
2
(2) A “hay spike” is installed near
the center of the tub floor at the end
of the tub mill. This “hay spike”
directs hay or crop residues to take a
path around the end of the mill. This
improves mill feeding and reduces
hammer wear.
(3) The heavy-duty “slug buster”
enhances the hammer’s cutting action
and product flow to the mill.
(4) The “BIG BITE” hammer’s can
swing up to 180˚, thus limiting how
far the hammers can lay back under
the tough grinding conditions.
Big capacity in a compact
package....that’s what you get
with the H-1000.
1
The “BIG BITE” tub is driven by a
(1)hydraulic motor through a
heavy-duty (2)roller chain. This
drive method provides for a
responsive and smooth transmission
of power to the tub.
2
1
3
ROCK PICKERS
The product is taken
away from the belly pan
augers with a 18” wide by
20’ long high-capacity
(1)discharge conveyor.
The conveyor height is
hydraulically controlled.
A hefty (2)hydraulic
cylinder transmits its
lifting force to the
conveyor through a strong
steel linkage system. It’s
all controlled by an easy
push or pull of a simple
(3)hydraulic lever.
GRAIN DRILLS
The two heavy-duty and high
capacity augers mounted in the belly
pan, convey the product to the
discharge conveyor. The auger and
pan combination provides for a highspeed transfer of the product and for
a clean, leak-free environment under
the tub grinder.
TUB GRINDERS
The tub rotation is controlled by
the DuraTech electronic
governor. This electronic
governor allows the engine speed
to remain constant, as the tub
rotation speed varies to control
the feed rate to the hammer mill.
BALE PROCESSORS
2
44 1/2” (113.03 cm)
26” (66.04 cm) with hammers
extended
Feed Opening
27” x 45” (68.6 m x 114.3 cm)
3/8” (.952 cm) hardened swing
Hammers
Number of Hammers 64
Rods
15/16” (2.38 cm) case hardened
Mill Plates
3/16” (.476 cm) thick x 15 3/4”
dia. (40.0 cm)
Mill Shaft
3” (7.62 cm) stress proof steel
Drive End Bearing
2 3/4” (6.94 cm) pillow block
Idle End Bearing
2 7/16” (6.19 cm) pillow block
Screens
1/4” (.635 cm) thick, various hole
sizes from 1/8 (.031 cm) to 4"
(10.16 cm)
2,400 sq. in. (609654 sq cm)
PTO through multiple vee belts
PTO Type 1000 RPM, 1
3/8”(3.49 cm), 21 spline shaft
80 to 175 Horsepower
Recommended PTO
TUB FEATURES
Loading Height
7’11” (2.41 m)
Tub Width at Flare
10’3” (3.12 m)
Depth
44 1/2” (113.03 cm)
Tub Inside Diameter 8’ (2.44 m)
at Base
Tub Wall Thickness
14 gauge (1.89 mm)
Tub Floor Thickness 10 gauge (3.42 mm)
Drive Mechanism
electro/hydrostatic
Speed Control
electronic governor
Hydraulic Oil Capacity 12 gal. (45.42 l)
BELLY PAN AUGERS
Type
double free floating augers
Auger Size
9” x 96” (22.86 cm x 243.84 cm)
Width
33 3/4” (85.73 m)
Drive
Mechanical
DISCHARGE CONVEYOR
Type
rubber belt with cleats
Rollers
“Easy Clean Roller”
Drive
mechanical
Length
20’ long (6.09 m)
Width
18” (45.72 cm)
Maximum Conveyor
Lift Height
13’ 9” (4.19 m)
Conveyor Lift
hydraulic
Conveyor Lift Cylinder 3 1/2” x 8” (8.89 cm x 20.32 cm)
Conveyor Fold
spring assist manual fold
OPERATOR CONTROLS
Tub Rotation
3 position hydraulic valve for
clockwise, stop and
counterclockwise
Tub Speed
DuraTech model RCB93
Electronic Governor sets
engine load by controlling
tub rotation speed
Conveyor Lift
3 position hydraulic valve for
raise, hold & lower
WEIGHT
Total
6,400 lbs. (2903 kg)
TRANSPORTATION DIMENSIONS
Width
10’ 3” (3.12 m)
Length
21’ 4” (6.50 m)
Height
10’ 2” (3.09 m)
CHASSIS FEATURES
Towing Arrangement clevis type for hitch pin
Tires
two 9.5 x 14 (24.13 cm x 35.56 cm)
Wheels
Drop Center Rims
Bearings
Tapered Roller Bearings
OPTIONS
Loose Hay Guide • Grain Grinding Hopper •
Ear Corn Kit • Geyser Plate • Mill Grate • Screen
Sizes from 1/8” (.031 cm) to 4” (10.16 cm) Round Hole •
Highway Tires
[H-1000 Series II]
Screen Area
Drive
Tractor
SPECIFICATIONS
HAMMERMILL
Length
Diameter
10' 2"
(3.10 m)
HAYBUSTER
13' 9"
(4.19 m)
9' 11"
(3.02 m)
21' 4"
(6.50 m)
27' 8"
(8.43 m)
10' 3"
(3.12 m)
8'
(2.43 m)
7' 11"
(3.63 m)
PO Box 1940
Jamestown, ND 58402-1940
Phone: (701) 252-4601
Fax: (701) 252-0502
Website: www.haybuster.com
DuraTech Industries International, Inc. reserves the right to
change its products or their specifications at anytime without
notice or obligation. Illustrations, specifications, and descriptions
contained herein were accurate at the time of publication, but
are subject to change without notice. Illustrations may include
optional equipment or accessories and may not include all
standard equipment.
UP 3000R5 12/05