AKAI PDP4206EM Service Manual

Transcription

SERVICE MANUAL
Model:
PDP
Safety Precaution
Technical Specifications
Block Diagram
Circuit Diagram
Basic Operations & Circuit Description
Main IC Specifications
Product Specification of PDP Module
Trouble Shooting Manual of PDP Module
Spare Part List
Exploded View
If you forget your V-Chip Password
Software Upgrade
This manual is the latest at the time of printing, and does not
include the modification which may be made after the printing,
by the constant improvement of product.
Safety Precaution
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL ONLY.
PRECAUTIONS DURING
SERVICING
1. In addition to safety, other parts and
assemblies are specified for conformance with
such regulations as those applying to spurious
radiation. These must also be replaced only
with specified replacements.
Examples: RF converters, tuner units, antenna
selection switches, RF cables, noise-blocking
capacitors, noise-blocking filters, etc.
2. Use specified internal Wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
3. Use specified insulating materials for hazardous
live parts. Note especially:
1) Insulating Tape
2) PVC tubing
3) Spacers (insulating barriers)
4) Insulating sheets for transistors
5) Plastic screws for fixing micro switches
4. When replacing AC primary side components
(transformers, power cords, noise blocking
capacitors, etc.), wrap ends of wires securely
about the terminals before soldering.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the product’s enclo
sure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
MAKE YOUR CONTRIBUTION
TO PROTECT THE
ENVIRONMENT
Used batteries with the ISO symbol
for recycling as well as small accumulators
(rechargeable batteries), mini-batteries (cells) and
starter batteries should not be thrown into the
garbage can.
Please leave them at an appropriate depot.
WARNING:
Before servicing this TV receiver, read the
SAFETY INSTRUCTION and PRODUCT
SAFETY NOTICE.
SAFETY INSTRUCTION
The service should not be attempted by anyone
unfamiliar with the necessary instructions on this
apparatus. The following are the necessary
instructions to be observed before servicing.
1. An isolation transformer should be connected in
the power line between the receiver and the
AC line when a service is performed on the
primary of the converter transformer of the set.
2. Comply with all caution and safety related
provided on the back of the cabinet, inside the
cabinet, on the chassis or picture tube.
5. Make sure that wires do not contact heat
generating parts (heat sinks, oxide metal film
resistors, fusible resistors, etc.)
6. Check if replaced wires do not contact sharply
edged or pointed parts.
7. Make sure that foreign objects (screws, solder
droplets, etc.) do not remain inside the set.
3. To avoid a shock hazard, always discharge the
picture tube's anode to the chassis ground
before removing the anode cap.
4. Completely discharge the high potential voltage
of the picture tube before handling. The picture
tube is a vacuum and if broken, the glass will
explode.
5. When replacing a MAIN PCB in the cabinet,
always be certain that all protective are
installed properly such as control knobs,
adjustment covers or shields, barriers, isolation
resistor networks etc.
6. When servicing is required, observe the original
lead dressing. Extra precaution should be given
to assure correct lead dressing in the high
voltage area.
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in this
apparatus have special safety-related
characteristics.
These characteristics are offer passed
unnoticed by visual spection and the protection
afforded by them cannot necessarily be obtained
by using replacement components rates for a
7. Keep wires away from high voltage or high
tempera ture components.
higher voltage, wattage, etc.
The replacement parts which have these
8. Before returning the set to the customer,
always perform an AC leakage current check
special safety characteristics are identified by
marks on the schematic diagram and on the parts
on the exposed metallic parts of the cabinet,
such as antennas, terminals, screwheads,metal
list.
overlay, control shafts, etc., to be sure the set
is safe to operate without danger of electrical
read the parts list in this manual carefully. The
use of substitute replacement parts which do not
shock. Plug the AC line cord directly to the
AC outlet (do not use a line isolation
have the same safety characteristics as specified
in the parts list may create shock, fire, or other
transformer during this check). Use an AC
voltmeter having 5K ohms volt sensitivity or
hazards.
9. Must be sure that the ground wire of the AC
more in the following manner.
Connect a 1.5K ohm 10 watt resistor paralleled
inlet is connected with the ground of the
apparatus properly.
by a 0.15µF AC type capacitor, between a
good earth ground (water pipe, conductor etc.,)
and the exposed metallic parts, one at a time.
Measure the AC voltage across the combination
of the 1.5K ohm resistor and 0.15 uF
capacitor. Reverse the AC plug at the AC
outlet and repeat the AC voltage measurements
for each exposed metallic part.
The measured voltage must not exceed 0.3V
RMS.
This corresponds to 0.5mA AC. Any value
exceeding this limit constitutes a potential
shock hazard and must be corrected
immediately.
The resistance measurement should be done
between accessible exposed metal parts and
power cord plug prongs with the power switch
"ON". The resistance should be more than
6M ohms.
AC VOLTMETER
Good earth ground
such as the water
pipe, conductor,
etc.
Place this probe
on each exposed
metallic part
AC Leakage Current Check
Before replacing any of these components,
MODEL :
Technical
Specifications
DATE FIRST ISSUED
ISSUE
PDP4206EM
42” Plasma Monitor
RAISED BY
CHECKED BY
NUMBER OF PAGES
1
REVISIONS
ISSUED
DATE
9
DESCRIPTION
SPECIFICATION AGREED :
RAISED BY :
SIGNATURE
DATE
......................................................................................
......
...........................
...
......................................................................................
......
...........................
...
Q/A DEPARTMENT
......................................................................................
.......
...........................
...
CUSTOMER
......................................................................................
.......
...........................
...
......................................................................................
.......
...........................
...
R & D DEPARTMENT
COMMERCIAL DEPARTMENT
PRODUCTION DEPARTMENT
SPECIFICATION APPROVED :
SIGNATURE :
.
NOTE :
Only documents stamped “Controlled Document” to be used for manufacture of production parts.
DATE :
Technical
1.
CONTINUATION PAGE
Specifications
PDP420
NUMBER
2
OF
9
PAGES
Standard Test Conditions
All tests shall be performed under the following conditions, unless otherwise specified.
1.1
Ambient light
:
150ux (When measuring IB, the ambient luminance
≦0.1Cd/m2)
1.2
Viewing distance
:
50cm in front of PDP
1.3
Warm up time
:
30 minutes
1.4
PDP Panel facing
:
no restricted
1.5
Measuring Equipment :
PC, Chroma 2225 signal generator (with Chroma digital
additional card) or equivalent, Minolta CA100 photometer
1.6
Magnetic field
:
no restricted
1.7
Control settings
:
Brightness, Contrast, Tint, Color set at Center(50)
1.8
Power input
:
110~120Vac
1.9
Ambient temperature :
1.10 Display mode
:
1.11 Other conditions
:
20°C ± 5°C (68°F ± 9°F)
31.5KHz/60Hz (Resolution 852 x 480)
1.11.1
With image sticking protection of PDP module, the luminance will descend
by time on a same still screen and rapidly go down in 5 minutes. When
measuring the color tracking and luminance of a same still screen, be sure
to accomplish the measurement in one minute to ensure its accuracy.
1.11.2
Due to the structure of PDP, the extra-high-bright same screen should not
hold over 5 minutes for fear of branding on the panel.
Technical
CONTINUATION PAGE
Specifications
PDP4206EM
NUMBER
3
OF
9
PAGES
ELECTRICAL CHARACTERISTICS
2.
3.
Power Input
2.1
Voltage
:
110 ~120VAC
2.2
Input Current
:
3.5 / 1.5A
2.3
Maximum Inrush Current
Test condition
:
:
<30 A (FOR AC110V ONLY)
Measured when switched off for at least 20 mins
2.4
Frequency
:
50Hz to 60Hz(±3Hz)
2.5
Power Consumption
Test condition
:
:
≤ 330W
full white display with maximum brightness and
contrast
2.6
Power Factor
:
Meets IEC1000-3-2
2.7
Withstanding voltage
:
1.5kVac or 2.2kVdc for 1 sec
:
:
:
:
:
:
:
42” Plasma monitor
16:9
852x480
1000 cd/m² (Panel module without filter)
3000:1 (Panel module without filter)
Over 160°
English
Display
3.1
3.2
3.3
3.4
3.5
3.6
3.7
4.
Screen Size
Aspect Ratio
Pixel Resolution
Peak Brightness
Contrast Ratio (Dark room)
Viewing Angle
OSD language
Signal
4.1
AV & Graphic input
4.1.1 Composite signal
4.1.2 Y,C Signal
4.1.3 Component signal
4.1.4 Graphic I/P
:
:
:
:
4.1.5 PnP compatibility
4.1.6 I/P frequency
:
:
CVBS
S-Video
Y, Pb/Cb, Pr/Cr, HDTV compatible
Analog: D-sub 15pin detachable cable
Digital: DVI
DDC 1.0
fH: 31.5kHz to 60kHz/fV: 56.25Hz to 75Hz (640x480
recommended)
Technical
4.2
4.3
4.4
5.
6.
PDP4206EM
Audio input
Audio I/P(L/Rx5)
:
1 for DVI / D-Sub
1 for Y/ Pb/Pr
1 for Y/ Cb/Cr
1 for Video
1 for S-Video
Audio output
Audio O/P(L/Rx1)
:
1 for Line out
Other function
:
PIP, 16:9, 4:3, Zoom
Environment
5.1 Operating environment
5.1.1 Temperature
:
5.1.2 Relative humidity:
5.2
CONTINUATION PAGE
Specifications
Storage and Transport
5.2.1 Temperature
:
5.2.2 Relative humidity:
NUMBER
4
OF
9
PAGES
5ºC ~ 33°C
20% ~ 85%(non-condensing)
-20°C to 60°C(-4º to 140°F)
5% to 95%
Panel Characteristics
6.1
6.2
Type
Size
:
:
6.3
6.4
6.5
6.6
6.7
6.8
Aspect ratio
:
Viewing angle :
Resolution
:
Weight
:
Color
:
Contrast
:
6.9
Peak brightness :
LG V6
42”, 1005mm(width)x597mm(height)x61mm(depth)±1
mm)
16:9
Over 160°
852x480
14.8kg ±0.5 kg (Net)
16.77 million colors by combination of 8 bits R,G,B digital
Average 60:1 (In a bright room with 150Lux at center)
Typical 3000:1 (In a dark room 1/25 White Window
pattern at center).
Typical 1000cd/㎡ (1/25 White Window)
6.10 Color Coordinate Uniformity :
Test Pattern
:
Contrast; Brightness and Color control at normal
setting
Full white pattern
Average of point A,B,C,D and E +/- 0.01
Technical
CONTINUATION PAGE
Specifications
6.11 Color temperature
:
PDP4206EM
NUMBER
5
OF
9
PAGES
Contrast at center (50); Brightness center (50);
Color temperature set at Natural
x=0.285±0.02
y=0.293±0.02
6.12 Cell Defect Specifications
Subject to Panel supplier specification as appends.
7.
Front Panel Control Button
SEL. UP/Down Button
:
Push the key to selecting the item on OSD menu
Volume Up/ Down Button
:
Menu Button
:
Push the key to increase the volume up or down.
When selecting the adjusting item on OSD menu
increase or decrease the data-bar.
Enter to the OSD menu.
Input Select Button
:
Push the key to select the input signals source.
7.2
Stand by Button
:
Switch on main power, or switch off to enter power
Saving modes.
7.3
Main Power Switch
:
Turn on or off the unit.
7.1
8.
OSD Function
8.1
Audio
:
Adjust or Select Volume; Bass; Treble; Balance; SRS; BBE; AVC;
Int./Ext. Speaker.
8.2
Picture
:
Adjust or Select Brightness; Contrast; Sharpness; Scaling (Picture
changes According to Fill or One to One.; DNR; Video Format;
More options for Y/Pb/Pr and VGA ( H. Position, V. Position Phase,
Frequency)
8.3
OSD
:
Position; OSD H. Position; OSD V. Position; OSD Timeout;
OSD Backgroud; Language.
8.4
Tools
:
Factory Reset; Source Scan; Blank Color; Turn Off Timer; Screen
Saver; Saver Mode.
8.5
CC-V Chip :
TV Channel Blocking; Movie Blocking; Change Blocking Password;
Clear Password; CC Mode; CC Background.
Technical
9.
Specifications
CONTINUATION PAGE
PDP4294LV1
NUMBER
6
OF
9
PAGES
Agency Approvals
Safety
UL60950
Emissions
FCC class B
10. Reliability
11.1 MTBF
11. Accessories
:
20,000 hours(Use moving picture signal at 25°C ambient)
:
User manual x1, Remote control x1, Stand x1, Power cord x1,
Battery x 2, Accessories box x 1.
Technical
CONTINUATION PAGE
Specifications
PDP4206EM
NUMBER
7
OF
12. Supportthe Signal Mode
The PDP can support the different from DVI or VGA Signal Mode in 24 kinds
NO.
Resolution
1#
2#
3
4
5
6
7#
8
9
10
11
12
13
14
15
16
17
18*
19
20*
21
22
23
24#
640 x400
640 x400
640 x480
640 x480
640 x480
640 x480
640 x480
800 x600
800 x600
800 x600
800 x600
800 x600
832 x624
1024 x768
1024 x768
1024 x768
1024 x768
1152x864
1152x864
1152x864
1280x1024
1280 x960
1280 x960
1280x720
Horizontal
Frequency
(KHz)
31.47
37.90
31.50
35.00
37.50
37.86
43.30
35.16
37.90
46.90
48.08
53.70
49.00
48.40
56.50
60.00
68.70
54.53
67.52
63.86
63.37
75.02
60.02
44.96
Vertical
Frequency
(Hz)
70.08
85.00
60.00
67.00
75.00
72.81
85.00
56.25
60.32
75.00
72.19
85.00
75.00
60.00
70.00
75.00
85.00
60.00
75.02
70.02
60.01
75.02
60.02
59.95
Note: DVI could not support * of signal mode.
VGA could not support # of signal mode.
- Press “DISPLAY” button to confirm the input signal format.
Note: Some data will be updated in five seconds if you change them.
Dot Clock
Frequency
(MHz)
25.17
31.5
25.18
30.24
31.50
31.50
36.00
36.00
40.00
49.50
50.00
56.25
57.27
65.00
75.00
78.75
94.50
80.37
108.03
94.51
111.51
126.00
108.04
74.19
9
PAGES
Technical
13.
Specifications
CONTINUATION PAGE
PDP4206EM
NUMBER
8
Remote Function+
Mute
YPbPr
PC
C/C
VOL +/Menu Left/Right
Up/Down
Left/Right
Button
SRS
ZOOM plus/minus
Display
Sleep
Standby on/off
PIP
Video
Number Buttons/
Channel up/
Channel down/
Return
V-CHIP
I. P. C
I. S. C
EXIT Button
Input
BBE
Wide
Freeze
F.WHITE
AUTO
OF
9
PAGES
Technical
Specifications
CONTINUATION PAGE
PDP4206EM
NUMBER
9
OF
9
PAGES
PHYSICAL CHARACTERISTICS
14. Power Cord
Length
:
1.8m nominal
Type
:
optional
:
“Black” colour as defined by colour plaque reference number
15. Cabinet
15.1 Color
15.2 Weight (with stand)
Net weight
:
84.5lbs (38.3kg)
15.3 Dimensions(with stand)
Width
Height
Depth
:
:
:
40-7/8 inches (1040mm)
27-1/4 inches (692mm)
11-1/4 inches (286mm)
Block Diagram
LVDS Input
Control Signal
(Serial Interface)
Input
Interface
Controller
Vs(180V~190V)
Memory
Controller
Va(55V~65V)
Vcc(+5V)
Driver
Timing
Controller
APL Data
Color Plasma Display Panel
852 X 480 pixels
Common sustain driver
Scan Driver
Display data, Driver timing
Address Driver
☞ Applied Voltage level is specified at the time when Full-White pattern is displayed on the panel.
Block Diagram
Circuit Diagram
-
Power supply board of PDP Module, DGP-420WXGA
Power supply board of PDP Module, USP490M-42LP
Main (Video) board
Audio/Tuner board
Keypad board
Remote control receiver board
External L/R Speakers board
Remote control board
5
4
CN01
3-176976-2
2
1
L104
CH108200S
L103
CH108200S
R108
5W 15
R103
5W 20
T208
PFC COIL 200uH
D102
FEP30JP
PFC +
PFC+
190VS
CN03
3-176976-1
C101
275VAC 1uF
RELAY1
SDT-SH-118DM
TNR101
14D 621K
Q102,Q103,Q109
SPW20N60C3*3
R603
BD101
D25XB60
R112
R224
2.2M
PFC VCC
R115
1.5KF
R109
1W 4.7
3K
C108
680pF
R106
1W 4.7
R107
1W 4.7
R116
10KF
D213
LL4148
R130
240KF
C114
0.68uF
R133
33KF
R114
R132
33KF
C115
3
EN
10
C220
RYC
D104
US1M
R142
6.8KF
R141
4.7KF
Q207
KRC103M
8
0.001uF
7
CT
R235
4.7KF
1
RT
C211
0.001uF
2
FB
R236
10KF
C301,301A
10V 2200uF*2
OUT
IS +
3
R608
120KF
Q702
KTC3207
VR601
5K
C212
0.0047uF
D211
1N5234B
T206
VA EER4042
D700
FSF10A60
60VA
R303
1KF
R704
22KF
R253
2W 240K
R700
VA
VS
R155
100KF
R152
100KF
R154
100KF
R153
100KF
R151
100KF
R150
100KF
R149
100KF
R148
100KF
R305
5W15
PFC ON/OFF
C213
630V 0.01uF
VA VCC
D209
LL4148
PC100
PC-17K1C
D303
1N5245B
R706
20KF
R229
1W 4.7F
VA DET
PC102
R707
2.7KF
Q208
KTA1281
Q300
FQP17N40
Q108
KTC3198Y
C701,702,704
100V 330uF
Q209
SPW11N80C3
R306
5W6.8
R245
10KF
GND
60VA
C304
50V 4.7uF
R247
1.2K
R246
5W 0.2
PFC GND
C215
C500
1KV0.001uF
R520
470F
R502
0
D202
BYV26EGP
D5001
SF30SC6
PC202
C200
630V 0.01uF
Q201
SPW11N80C3
IC500A
KA431AZ
R210
1W 10F
R511
15KF
6
4.7KF
SEL
CABLE
2
7
7
3
11
4
12
7
171825-4
171825-7
5
1-171825-2
9
171825-9
190VS
2
1
1
1-1123723-4
1-1123723-0
4
5VCTRL
8
1-1123723-8
CN809
9VSC
8
171825-8
1
2
171825-2
3
11
100F
50V0.01uF
10KF
50V0.01uF
R422
C411
10KF
R416 1KF
R415
15
16
17
18
19
20
21
14
INT1/RB3
11
INT0/RB2
10
BUZ/RB1
9
AN0/AVref/RB0
8
RD1
7
RD2
RD3
Xin
Xout
|RESET
Vss
RC0
RD0
6
VDD
5
AN6/RA6
AN6/RA6
4
13
2
7
6
21
20
16
18
17
19
변경
후
PH967C6
FEP30JP
JSS 2209
R420 4.7KF
R418 1KF
R417 1KF
R412 1KF
330F
R411
3
13
2
12
2
15
9
4
5
8
1
RY ON/OFF
6
8
6
VS ON
6
60VA
RLY ON
3
10
변경
전
DGP-420WXGA
5VD OUT
3
2
ACD OUT
5
7
9
5
3
Xout
MULTI ON/OFF
4
5
5VCTRL
AC DET
3
4
4
6
2004/07/28
A
R423 1KF
3
5
CN805
5
방전CTL
5VSC
330F
6
8
4
4
7
50V 0.1uF
R410
2
VA,VS ON/OFF
2
+30V DET
7
1
50V 0.1uF
C409
+9V DET
3
1
1KF
6
5VCTRL
1KF
8
R404
2
+12V DET
5VD
24V/30V
50V 0.1uF
C408
VA DET
5
1
C407
CN808
9
190VS
50V 0.1uF
+5V DET
4
VS_ON
12VSC
CN802
3
CN807
50V 0.1uF
C406
R403 1KF
2
SB5V
10
C405
일자/사유
SW400
VS DET
1
60VA
GND
ACD
RLY_ON
9VSC
1
4
+5VSTBY
3
CN801
50V 0.1uF
R409 2KF
CN806
CN804
50V 0.68uF
C404
PFC ON/OFF
1
C403
1KF
GND
AN5/RA5
AN4/RA4
1
R519
1.5KF
2
+9V DET
J2
0
GND
ON/OFF
GND
IC401
HMS87C1304A
9VSC
R518
3.9KF
C514
35V 47uF
RC1
R516
1KF
2
Vo
C516
35V 1000uF
2
Xin
+12V DET
R515
1.8KF
4
Vin
3
PC-17K1C
PC201
1
D10L20U
5VSC
CRST400
4MHZ
1
C410
LED400
GREEN
R514
2KF
CN803
A
R711
11KF
D212
1N5234B
C226
0.001uF
C401
50V 0.1uF
R526
D503
C227
0.001uF
C219
0.01uF
1
GND
C262
4.7uF
VR700
5K
3
OUT
IC502
KIA378R09PI
C201
0.01uF
Q701
KTC3207
IC202
KA7552A
R421
VCC
C400
50V 0.1uF
+12V /1.0A
C511
35V 47uF
R262
1KF
C520
VA ON/OFF
R709
36KF
PC206
3
IS +
GND
1
22
3
2
Vo
R532
1W 2.7K
C510
35V 470uF
C208
470pF
R703
36KF
IC400
KIA7045AP
24
Vin
D502
PC202
PC-17K1C
R719
18KF
NO
R406
VCC
1KF
R402
RA3/AN3
1
31GF6
4
R401
R513
2.7KF
R531
IC200
KA7552A
R217
10KF
R714
18KF
LED401
RED
R405
R219
10K
Q202
KRC103M
IS +
R712
18KF
REVISION HISTORY
R510
5W 1K
2
FB
0.22uF
R721
45.3KF
PC205
R400
1KF
5VCTRL
GND
ON/OFF
2
C205
R717
45.3KF
R252
1W 100R
PC206
PC-17K1C
C261
4.7uF
IC501
KIA278R12PI
C519
R718
45.3KF
5
OUT
PWM0/COMP0/RB4
C507
35V 47uF
5
R220
1/4W 100R
3
R702
33KF
10KF
C214
0.01uF
+30V DET
R512
15KF
R508
0R
OUT
R708
18KF
12
R507
5W 2.7K
GND
RT
R701
18KF
+30V/1.0A (+24V/1.25A)
R525
56KF
4
CT
1
FB
CS
R414 2KF
Output
6
7
4.7KF
GND
0.001uF
R218
R710
18KF
B
35V 47uF
C204
2
RA0/EC0
Adj
SUF30J
C506
50V 220uF
R216
100KF
R249
10KF
2
R509
3.3KF
CS
0.047uF
23
C505
1KV 0.001uF
1
R237
5W 0.1
R720
45.3KF
R261
1KF
PC205
PC-17K1C
3
R214
360RF
8
C218
RA2/AN2
R505
1W 4R7
Input
R212
10KF
D501
1uF
RT
GND
Q200
KTA1281
C203
CT
1
R251
R504
1.8KF
R522
4.7KF
R716
45.3KF
IC500
KA317
B
C202
7
4.7KF
R408 1KF
D203
LL4148
0.001uF
R250
3
D206
LL4148
C530
1uF
C217
+5V DET
R501
3.3KF
GND
LL4148
Q210
KRC103M
R503
1KF
PC201
8
1KF
D200
MULTI VCC
5VSC
1uF
VCC
+5VCTRL
VR500
2K
C216
GND
D500
SF30SC6
R248
100KF
R407
R209
2W 240K
C504,C555~C557
10V 2200uF*4
4
C550~C554
10V 2200uF*5
R715
45.3KF
35V 47uF
MULTI ON/OFF
L500
6*20 2.5uH
RA1/AN1
R500
1W 10
C
R705
20KF
1KV 100pF
1W 10
D302
US1M
R307
5W6.8
방전 CTL
AC DET
C700
D208
BYV26EGP
GND
D301
US1M
R615
18KF
PFC +
IC300
KA431AZ
R156
1KF
T207
MULTI EER4042
R627
120KF
R607
130KF
IC201
KA7552A
PC101
C302
0.68uF
PFC VCC
PFC +
R606
270KF
PC204
D226
LL4148
D106
US1M
R613
120KF
R243
1W 47R
C225
0.1uF
C263
10uF
R302
1.02KF
R146
2W 100
C120
35V 47uF
R604
120KF
R628
120KF
5
PC204
PC-17K1C
+5VSTBY
R301
220F
CS
C210
R260
2.4KF
D105
US1M
C128
35V 470uF
1uF
C117
35V 470uF
3
D108 1N5236B
R175
0
C209
D111
1N4148
U100
5M0280R-YDTU
1
C118
0.01uF
C126
250V 0.47uF
R602
2W 100K
35V 47uF
L301
PC101
PC-17K1C
PC100
VCC
R190
200KF
FB
R192
56KF
4
R195
56KF
0.1uF
R198
56KF
R140
7.5KF
C119
R189
200KF
2
R193
56KF
DRAIN
R196
56KF
GND
R199
56KF
Q107
KTC3198Y
R233
100KF
R136
10KF
D300
SB560
C121
630V 0.01uF
AC-1
C
PC102
PC-17K1C
27uH
D107
US1M
R231
5W 0.05
R620
2W 100K
R110
10KF
10KF
PFC+
R145
2W 240K
R232
1K
R137
T100
STBY EE1927
R143
3W 470K
R230
4.7KF
6
4
IS
PK
VR
R134
24KF
CA
9
VS
8
R131
33KF
D
GND
Q206
KTA1281
4
R128
75KF
VC
R127
75KF
GT
Q105
KTA1281
R111
100F
15
R126
75KF
U101 UC3854N
GND
R125
75KF
IA
R612
12KF
Q106
KSP2907
R176
10KF
16
VS DET
C221
630V 0.1uF
1KV 220pF
190VS
Q104
KTC3209
C109
68PF
6
1W4R7
R228
1W 4.7
C123
35V 47uF
D109
1N5236B
13
50V 10uF
14
0.0022uF
12
10KF
1
VI
VO
RE
7
R129
150KF
2
R124
220KF
11
R122
18KF
C113
2.2uF
RS
R123
330KF
5
C112
330pF
R135
R121
160KF
CT
R120
160KF
SS
R119
180KF
C116
R118
180KF
MO
0.1uF
R117
180KF
R611
300KF
C601
R225
1M
R144
10F
R113
24KF
R227
1W 4.7
C111
PFC+
C602
250V 820uF
3KF
C102,103
250V 0.001uF
C110
470pF
D601
FSF10A60
R223
2.2M
TNR102
14D 621K
D
1KV 220pF
Q203,204
SPW11N80C3*2
C206
630V 0.047uF
VA VCC
R104
10W 0.02
LL4148
L102
23mH
C600
1W4R7
R610
300KF
R222
2.2M
D204
LL4148
D103
R600
C222
630V 0.1uF
D205
BYV26EGP
C105,106
450V 330uF
C104
630V 1uF
RYC
R609
300KF
R226
2W 240K
R221
2.2M
R102
1W 390KJ
1
D600
FSF10A60
T204,205
VS EER4042
L101
23mH
2
2
VCC
1
2
1
CN02
3-176976-1
3
VI
GND
F101
250VAC 8A
<
HIC_MICOM
m
D
<D
1
1
USP490M-42LP
5
4
INPUT
2
AFE
DVI
GBAIN
GGAIN
RXCm
RX0m
GHSYNC
RX1m
RXCp
HDCBIN
HDYIN
RX1p
RX2p
GRAIN
Y
RX0p
RX2m
GVSYNC
CB
HDCRIN
CR
D
3
RXCm
RX0m
RX1p
RX1m
RX0p
GDFEOE
RX2m
RX2p
RXCp
HDCBIN
HDYIN
GAFEOE
VGASEL
GVSYNC
GCOAST
HDCRIN
GRAIN
SCL
GBAIN
GBLKSPL
GGAIN
SDA
GHSYNC
GRE[7:0]
GPEN
GBE[7:0]
GVS
GBO[7:0]
GFBK
GHS
GGE[7:0]
GCLK
GRO[7:0]
GGO[7:0]
GBE[7:0]
GRE[7:0]
GHS
GCLK
GFBK
GGE[7:0]
GVS
04_AFE
03_DVI
02_INPUT
MEMORY
C
VCP3230
VVINT
CB
RESETn
Y
SDA
CR
STBLED
VUV[7:0]
VVHS
VY[7:0]
VVCLK
SCL
VVVS
VFIELD
MUTE
POWER_ON
MUTE1
IR
NV320
SDA
SCL
VVHS
RESETn
VVCLK
NDSP_EN
VY[7:0]
VUV[7:0]
VVVS
VG[7:0]
VB[7:0]
VR[7:0]
VCLK
VVS
VHS
VPEN
SDA
SCL
ROMWEn
ROMOEn
VPPEN
D[15:0]
A[19:1]
07_MEMORY
06_NV320
05_VCP3230
B
POWER
MISC
LED-G
ICSSTM
ICSCLK
ICSSTD
LED-R
ICSDAT
TXD
RDn
D[7:0]
CS1n
STBLED
TMDS
DBO[7:0]
DHS
DENG
DENR
DGE[7:0]
DRE[7:0]
DGO[7:0]
DRO[7:0]
DCLK
DVS
09_TMDS
DENB
DBE[7:0]
LVDS
DENG
DCLK
DVS
DHS
DTXON
RESET-2
SCL
SDA
CPUGO
PDPGO
PDWN
IRQ
DGE[7:0]
DRE[7:0]
DBE[7:0]
DCKEXT
MCKEXT
RXD
RESET
RESETn
NMI
POWER_ON
IRRCVR1
11_POWER
10_MISC
1
PW171
D[15:0]
SDA
A[19:0]
GFBK
CS1n
VPPEN
RDn
NMI
VR[7:0]
VCLK
VG[7:0]
VB[7:0]
GHS
GCLK
GRE[7:0]
GBO[7:0]
GBE[7:0]
GGO[7:0]
GRO[7:0]
GVS
GGE[7:0]
MCKEXT
RXD
08_PW171
IRRCVR1
RESET
DCKEXT
VPEN
VVS
VFIELD
GPEN
ICSCLK
ICSSTD
ICSSTM
ICSDAT
LED-R
LED-G
NDSP_EN
DTXON
VGASEL
GAFEOE
GDFEOE
VVINT
VHS
MUTE
SLEEP1
PIO3
CPUGO
PDPGO
RESET-2
PDWN
IRQ
DGE[7:0]
DBE[7:0]
DRO[7:0]
DGO[7:0]
DRE[7:0]
DBO[7:0]
DCLK
GBLKSPL
GCOAST
ROMWEn
ROMOEn
TXD
DVS
DENB
DENG
DENR
DHS
SCL
D
C
B
12_LVDS
A
A
上海家影多媒体技术有限公司 Shanghai Jiaying Multimedia Technology Co.,Ltd
Title
PW171-LGPDP
Size
B
File
TOP
Date:
Drawn by:
5
4
3
2
Thursday, December 09, 2004
Checked by:
Rev
c
Sheet
1
of
1
12
Approved by:
AVDD
AVDD
AVDD
VCC
C34
C35
C36
C37
C38
C39
C40
C41
C42
C43
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
U5
LM2937_SOT223
1
0.1uF
V33
V33
V33
V33
V33
V33
VCC
U6
LM2937_SOT223
1
C45
C46
C47
0.1uF
47uF
0.1uF
VI
VO
AVDD
3
C48
C49
0.1uF
47uF
D
V33
C50
C51
C52
C53
C54
C55
C56
C57
C58
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
47uF
PVDD
AVDD
V33
PVDD
34
35
PVDD
11
22
23
69
78
79
PVDD
VO
26
27
39
42
45
46
51
52
59
62
D
VI
C44
PVDD
3
TAB
AVDD
GND
AVDD
4
AVDD
1
2
AVDD
TAB
AVDD
2
GND
AVDD
3
2
AVDD
4
4
5
C59
2
3.9nF
0.1uF
R16
3.3K
74LVC126A
GFILT
FILT
SDA
SCL
57
56
55
SDA
SCL
A0
GBLKSPL
GCOAST
38
29
CLAMP
COAST
7
TP8
C
VGASEL
A/B
OE
HDCRIN
HDYIN
HDCBIN
2
5
11
14
A1
A2
A3
A4
GRAIN
GGAIN
GBAIN
3
6
10
13
B1
B2
B3
B4
VCC
PI5V330
VCC
16
Y1
Y2
Y3
Y4
4
7
9
12
GMRED
GMGRN
GMBLU
VCC
GND
47nF
C62
GRIN
54
RAIN
47nF
C63
1nF
C64
GGIN
GSOGIN
48
49
GAIN
SOGIN
GBIN
43
BAIN
30
31
HSYNC
VSYNC
58
37
REFBYP
MIDSCV
47nF
C65
0.1uF
10
B
9
GHSYNC
U8C
8
GVREF
GMIDV
GBHSY
74LVC126A
5
U8B
6
C67
C68
0.1uF
0.1uF
47R
9
8
7
6
5
4
3
2
ADG0
ADG1
ADG2
ADG3
ADG4
ADG5
ADG6
ADG7
47R
AD9883A_140
BLUE0
BLUE1
BLUE2
BLUE3
BLUE4
BLUE5
BLUE6
BLUE7
19
18
17
16
15
14
13
12
ADB0
ADB1
ADB2
ADB3
ADB4
ADB5
ADB6
ADB7
47R
DATACK
67
ADCK
HSOUT
SOGOUT
VSOUT
66
65
64
ADHS
ADSOG
ADVS
GREEN0
GREEN1
GREEN2
GREEN3
GREEN4
GREEN5
GREEN6
GREEN7
47R
47R
47R
47R
GRE[7:0]
RP14 GRE0
GRE1
GRE2
GRE3
RP15 GRE4
GRE5
GRE6
GRE7
C
GGE[7:0]
RP16 GGE0
GGE1
GGE2
GGE3
RP17 GGE4
GGE5
GGE6
GGE7
GBE[7:0]
RP18 GBE0
GBE1
GBE2
GBE3
RP19 GBE4
GBE5
GBE6
GBE7
RP20
GBVSY
B
GCLK
GFBK
ADSOGR
GVS
TP9
13
1
10
20
21
24
25
28
32
36
40
41
44
47
50
53
60
61
63
68
80
4
GVSYNC
U7
8
C66
ADR0
ADR1
ADR2
ADR3
ADR4
ADR5
ADR6
ADR7
GND1
GND2
GND3
GND4
GND5
GND6
GND7
GND8
GND9
GND10
GND11
GND12
GND13
GND14
GND15
GND16
GND17
GND18
GND19
GND20
U9
1
15
77
76
75
74
73
72
71
70
RED0
RED1
RED2
RED3
RED4
RED5
RED6
RED7
33
TP7
PVD1
PVD2
C61
U8A
3
39nF
GFLT1
VDD1
VDD2
VDD3
VDD4
VDD5
VDD6
C60
AVD1
AVD2
AVD3
AVD4
AVD5
AVD6
AVD7
AVD8
AVD9
AVD10
1
V33
14
V33
12
74LVC126A
U8D
11
GHS
74LVC126A
GAFEOE
A
A
Main (Video)
Drawn by:
5
4
3
2
Checked by:
Approved by:
1
PVCC
AVCC
VCC
U3
LM2937_SOT223
R15
510
SIRES
C
96
EXT_RES
RX0p
RX0m
90
91
RX0p
RX0m
RX1p
RX1m
85
86
RX1p
RX1m
RX2p
RX2m
80
81
RX2p
RX2m
RXCp
RXCm
93
94
RXCp
RXCm
SII161
U4
OVCC
100
4
1
7
3
9
2
99
GDFEOE
OCK_INV
PIXS
DFO
STAG_OUT
ST
PDO
PD
RSVD
AGND1
AGND2
AGND3
AGND4
AGND5
PGND
8
SISCDT
QE0
QE1
QE2
QE3
QE4
QE5
QE6
QE7
QE8
QE9
QE10
QE11
QE12
QE13
QE14
QE15
QE16
QE17
QE18
QE19
QE20
QE21
QE22
QE23
10
11
12
13
14
15
16
17
20
21
22
23
24
25
26
27
30
31
32
33
34
35
36
37
SIBE0
SIBE1
SIBE2
SIBE3
SIBE4
SIBE5
SIBE6
SIBE7
SIGE0
SIGE1
SIGE2
SIGE3
SIGE4
SIGE5
SIGE6
SIGE7
SIRE0
SIRE1
SIRE2
SIRE3
SIRE4
SIRE5
SIRE6
SIRE7
RP1
47R
RP2
47R
QO0
QO1
QO2
QO3
QO4
QO5
QO6
QO7
QO8
QO9
QO10
QO11
QO12
QO13
QO14
QO15
QO16
QO17
QO18
QO19
QO20
QO21
QO22
QO23
49
50
51
52
53
54
55
56
59
60
61
62
63
64
65
66
69
70
71
72
73
74
75
77
ODCK
DE
VSYNC
HSYNC
44
46
47
48
CTL1
CTL2
CTL3
40
41
42
0.1uF
TP1
RP3
47R
RP4
47R
RP5
47R
RP6
47R
SIBO0
SIBO1
SIBO2
SIBO3
SIBO4
SIBO5
SIBO6
SIBO7
SIGO0
SIGO1
SIGO2
SIGO3
SIGO4
SIGO5
SIGO6
SIGO7
SIRO0
SIRO1
SIRO2
SIRO3
SIRO4
SIRO5
SIRO6
SIRO7
RP7
47R
RP8
47R
SICLK
SIDE
SIVS
SIHS
RP13
RP9
47R
RP10
47R
RP11
47R
RP12
47R
V33T
3
VO
C15
C16
0.1uF
47uF
GBE[7:0]
GBE0
GBE1
GBE2
GBE3
GBE4
GBE5
GBE6
GBE7
GGE0
GGE1
GGE2
GGE3
GGE4
GGE5
GGE6
GGE7
GRE0
GRE1
GRE2
GRE3
GRE4
GRE5
GRE6
GRE7
GBO0
GBO1
GBO2
GBO3
GBO4
GBO5
GBO6
GBO7
GGO0
GGO1
GGO2
GGO3
GGO4
GGO5
GGO6
GGO7
GRO0
GRO1
GRO2
GRO3
GRO4
GRO5
GRO6
GRO7
VI
D
V33T
L15
FB_420_OHM_200MA
OVCC
OVCC
OVCC
OVCC
OVCC
OVCC
GGE[7:0]
V33T
GRE[7:0]
GBO[7:0]
V33T
L16
FB_420_OHM_200MA
L17
FB_420_OHM_200MA
C17
C18
C19
C20
C21
C22
10uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
CVCC
CVCC
CVCC
CVCC
C23
C24
C25
C26
10uF
0.1uF
0.1uF
0.1uF
PVCC
C
PVCC
C27
C28
10uF
0.1uF
GGO[7:0]
V33T
L18
FB_420_OHM_200MA
AVCC
GRO[7:0]
TP2
TP3
TP4
TP5
AVCC
AVCC
AVCC
AVCC
C29
C30
C31
C32
C33
10uF
0.1uF
0.1uF
0.1uF
0.1uF
TP6
B
47R
GCLK
GPEN
GVS
GHS
GFBK
79
83
87
89
92
98
GND1
GND2
GND3
5
39
68
OGND1
OGND2
OGND3
OGND4
OGND5
B
19
28
45
58
76
C14
82
84
88
95
6
38
67
97
PVCC
D
AVCC1
AVCC2
AVCC3
AVCC4
AVCC
VCC1
VCC2
VCC3
OVCC1
OVCC2
OVCC3
OVCC4
OVCC5
18
29
43
57
78
1
SCDT
1
TAB
CVCC
2
GND
OVCC
3
4
4
2
5
A
A
Title
PW171-LGPDP
Main (Video)
Size
B
File
DVI INPUT
Date:
Drawn by:
5
4
3
2
Checked by:
Rev
C
Sheet
1
of
3
12
Approved by:
5
4
3
2
1
D[15:0]
JP1
VPPEN
1
3
FWPn
2
4
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
HDR_2X2
25
24
23
22
21
20
19
18
8
7
6
5
4
3
2
1
48
17
16
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
VPP
VCC
37
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
D16
29
31
33
35
38
40
42
44
30
32
34
36
39
41
43
45
GND1
GND2
46
27
VPP
C167
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
R69
R70
R71
3.3K
3.3K
3.3K
V33
2
D
R67
1K
R68
10K
VP1
SCL
SDA
Q5
3904
1
V33
U17
VP2
6
5
SCL
SDA
VCC
8
1
2
3
NC0
NC1
NC2
WP
7
GND
4
C168
0.1uF
24C16
C
VPPON
V33
JP2
FCEn
ICEn
V33
Q4
3906
VP3
22uF
Flash_8M
C
3
1
D
CE
OE
WE
RP
WP
BYTE
13
3
ROMOEn
ROMWEn
V33
V33
U16
26
28
11
12
14
47
2
V33
1
3
2
4
HDR_2X2
C169
0.1uF
VCC
A2
A4
A6
A9
A11
B
A12
A14
A17
A19
ROMOEn
D15
D14
D5
D4
D3
D2
D9
D8
A
VCC
V33
JP3
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
IRPn R72
R73
3.3K
3.3K
IA20 R74
IA21 R75
3.3K
3.3K
A1
A3
A5
A7
A8
A10
B
A13
A15
A16
A18
ROMWEn
D7
D6
D13
D12
D11
D10
D1
D0
A
HDR_30X2
Main (Video)
A[19:1]
Title
PW171-LGPDP
Size
B
File
FLASH
Date:
Drawn by:
5
4
3
2
Checked by:
Rev
C
Sheet
1
of
7
12
Approved by:
5
4
3
2
HDCR L1
FB_40_OHM_500MA
HDCRF
L2
FB_40_OHM_500MA
L3
FB_40_OHM_500MA
HDYF
L4
FB_40_OHM_500MA
L5
FB_40_OHM_500MA
HDCBF
L6
FB_40_OHM_500MA
1
HDCRIN
J1
CR
8
R1
R2
R3
75
75
75
3
C1
Y
9
D1
28
0.1uF
RX1m
RX1p
GRED
L7
GGREEN
GBLUE
FB_40_OHM_500MA
GREDF
L8
FB_40_OHM_500MA
L9
FB_40_OHM_500MA
GGREENF
L10
FB_40_OHM_500MA
L11
FB_40_OHM_500MA
GBLUEF
L12
FB_40_OHM_500MA
DVI_V
GVSYNC
GVCC1
GVCC1 GVCC1
R10
R11
R12
75
75
75
AVDD
GVCC1
GVCC1
D13
VCC
1
3
R13
2K
3
R14
2K
AVDD
3
D11
AVDD
3
3
D8
3
C8
C7
D9
12pF
1
BAV70L
B
C9
D10
12pF
12pF
D12
3
BAV70L
VCC
GVCC
L13
NS
C10
C11
VCC
GVCC1
L14
NS
C12
0.1uF
47uF_NS
A
GBAIN
GVCC
D14
2
GGAIN
GHSYNC
RXCp
RXCm
1
GRAIN
G5V
2
VCC
4
C
0.1uF
2
RX2m
RX2p
RX0m
RX0p
GND
C4
J15
DB15HD_V
6
1
11
7
2
12
8
3
13
9
4
14
10
5
15
GDC5V
1
2
3
24LC21A
2
C1
C2
C3
C4
C5
C6
26
2
C5
NC1
NC2
NC3
BAV99L
4
SCL
SDA
1
GND
VCLK
6
5
2
1
2
3
7
CSCL
CSDA
8
BAV99L
NC1
NC2
NC3
CVCK
VCC
1
SCL
SDA
8
GVCC1
U1
2
6
5
3.3K
BAV99L
GSCL
GSDA
R8
3.3K
2
VCLK
VCC
BAV99L
A_RED
A_GREEN
A_BLUE
A_HSYNC
A_GND1
NC2
A_GND2
SHELL2
12pF
1
1
7
R7
3.3K
BAV99L
1
GVCK
R6
GVCC
U2
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
D5
16
DATA2DATA2+
DATA2/4_SHLD
DATA4DATA4+
DDC_CLK
DDC_DATA
A_VSYNC
DATA1DATA1+
DATA1/3_SHLD
DATA3DATA3+
+5V
GND
H_PLUG_DET
DATA0DATA0+
DATA0/5_SHLD
DATA5DATA5+
CLK_SHLD
CLK+
CLK-
C3
D3
12pF
1
3
D7
1
B
25
3
GVCC1 GVCC1 GVCC1
3.3K
24LC21A
SHELL1
D2
3
D4
R9
3.3K
J2
NC1
3
BAV99L
BAV99L
GVCC
R5
BAV99L
BAV99L
R4
3
GVCC
17
GVCC
2
2
GVCC
D6
27
C2
GVCC1
2
GVCC1
3.3K
C
D
CR
YUV
GVCC
3
12pF
1
CB
AVDD
BAV99L
7
BAV99L
6
2
CB
5
HDCBIN
AVDD
2
AVDD
D
2
HDCB
4
1
3
HDYIN
BAV99L
Y
2
1
HDY
1
C13
0.1uF
47uF_NS
A
Title
PW171-LGPDP
Main (Video)
Size
File
Custom
Date:
Drawn by:
5
4
3
2
Rev
C
INPUT
Checked by:
Sheet
1
2
12
of
Approved by:
5
4
3
2
1
SDA
SCL
DBE[7:0]
47R
47R
47R
C277
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
DCLK
ARE0
ARE1
ARE2
ARE3
ARE4
ARE5
ARE6
ARE7
AGE0
AGE1
AGE2
AGE3
AGE4
AGE5
AGE6
AGE7
ABE0
ABE1
ABE2
ABE3
ABE4
ABE5
ABE6
ABE7
DGE[7:0]
B
DBE[7:0]
47R
47R
47R
47R
47R
RP50ARE6
ARE7
ARE0
ARE1
RP51ARE2
ARE3
ARE4
ARE5
RP52AGE6
AGE7
AGE0
AGE1
RP53AGE2
AGE3
AGE4
AGE5
RP54ABE6
ABE7
ABE0
ABE1
RP55ABE2
ABE3
ABE4
ABE5
DTXON
0
R144
CLKIN
51
52
54
55
56
3
50
2
4
6
7
11
12
14
8
10
15
19
20
22
23
24
16
18
27
28
30
25
TXIN0
TXIN1
TXIN2
TXIN3
TXIN4
TXIN6
TXIN27
TXIN5
TXIN7
TXIN8
TXIN9
TXIN12
TXIN13
TXIN14
TXIN10
TXIN11
TXIN15
TXIN18
TXIN19
TXIN20
TXIN21
TXIN22
TXIN16
TXIN17
TXIN24
TXIN25
TXIN26
TXIN23
17
32
R_F
PWRDN
2
4
6
8
10
12
14
16
18
20
0
R139
0
R140
CON20A
U31
DS90C383A
TXOUT0
TXOUT0
47
48
TXOUT1
TXOUT1
45
46
TXOUT2
TXOUT2
41
42
TXOUT3
TXOUT3
37
38
TXCOUT
TXCOUT
39
40
TXE0m
TXE0p
TXE1m
TXE1p
TXE2m
TXE2p
TXECKm
TXECKp
TXE3m
TXE3p
3WSDA 0
3WSCL 0
3WSLE 0
PDWN
R141
R142
R143
SCL
SDA
5
13
21
29
53
36
43
49
33
35
47R
31
1
3
5
7
9
11
13
15
17
19
34
C276
44
C275
DHS
DVS
DENG
DRE0
DRE1
DRE2
DRE3
DRE4
DRE5
DRE6
DRE7
DGE0
DGE1
DGE2
DGE3
DGE4
DGE5
DGE6
DGE7
DBE0
DBE1
DBE2
DBE3
DBE4
DBE5
DBE6
DBE7
J13
C274
C
DRE[7:0]
V33
C273
PVCC
47R
V33
1
9
26
47R
V33
VCC1
VCC2
VCC3
DGE[7:0]
RP60 ARE0
ARE1
ARE2
ARE3
RP61 ARE4
ARE5
ARE6
ARE7
RP62 AGE0
AGE1
AGE2
AGE3
RP63 AGE4
AGE5
AGE6
AGE7
RP64 ABE0
ABE1
ABE2
ABE3
RP65 ABE4
ABE5
ABE6
ABE7
47R
V33
GND1
GND2
GND3
GND4
GND5
OGND1
OGND2
OGND3
PGND1
PGND2
D
DRE0
DRE1
DRE2
DRE3
DRE4
DRE5
DRE6
DRE7
DGE0
DGE1
DGE2
DGE3
DGE4
DGE5
DGE6
DGE7
DBE0
DBE1
DBE2
DBE3
DBE4
DBE5
DBE6
DBE7
V33
OVCC
V33
DRE[7:0]
D
3WSDA
3WSCL
3WSLE
PDWN
J14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
C
JEA31
B
A
A
Main (Video)
Title
PW171-LGPDP
Size
B
File
LVDS OUTPUT
Date:
Drawn by:
5
4
3
2
Checked by:
Rev
C
Sheet
1
of
12
12
Approved by:
4
3
2
1
V33
LED
V33
13
ICSCLK
ICSDAT
ICSSTM
D
VDD
3
CLK1
11
CLK2
6
GND
5
OE
8
12
9
SCLK
DATA
STROBE
1
16
X1
X2
MCKEXT1
47
RMCK
ICSREF
V33
ICSSTD
IX1
IX2
Y3
13
OE
8
12
9
SCLK
DATA
STROBE
1
16
X1
X2
VDD
3
CLK1
11
CLK2
6
GND
5
MCKEXT
C232
D19
V33
C231
0.1uF
0.1uF
47
+5VIN
R102
V33
DCKEXT
NMI1
1
R106
ICS307
4
R107
SW1
SW_MOM_4P
2
1
2
3
4
0.1uF
V33
VDD
8
RESET
6
RESET
5
SENSE
RSTINn
2
RESIN
TLCCT
3
CT
1
CONTROL
C234
R389
0.1uF
STBLED PH-6A
STBLED
IR
3906
3
2
1
JP5
HDR_4X1
0.1uF
GND
IRRCVR1
Q6
1
+5V
1K
C
C242
4.7uF
R108
J9
IR
V33
U24
7
10K
3
C241
4.7uF
VCC
C233
R103
4.7K
C240
PH-3A
V33
4
CON5
FROM PDP
1
2
3
4
5
6
NMI
3
C
1
1K
SW2
SW_MOM_4P
V33
1
2
3
4
5
+5V
J8
2
XTAL14.31818
D
J16
+5V
DCKEXT1
RDCK
+5VIN
0.1uF
LED RED
C230
V33
U23
VCC
510
R99
V33
ICS307
R98
20K
U25
RESET
RESETn
4
200
RXD
R104
MC1P
MC1M
1
3
RRXD
12
9
ROUT1
ROUT2
11
10
4
5
TLC7733
R105
TXD
MC2P
MC2M
1K
B
R109 R110 R111 R112 R113 R114 R115
10K
10K
10K
10K
10K
10K
10K
V33
V33
V33
V33
V33
V33
V33
POWER_ON
R116
10K
V33
C238
C239
0.1uF
0.1uF
VCC
VCC
VP
16
2
RIN1
RIN2
13
8
MRXD
TIN1
TIN2
T1OUT
TOUT2
14
7
MTXD
C2P
C2M
VM
GND
6
15
MVM
C1P
C1M
10
CLOCK GENERATOR
MVP
MAX232A
C235
C236
C237
0.1uF
0.1uF
0.1uF
J7
5
9
4
8
3
7
2
6
1
DB9_V
B
11
U21
2
V33
3
5
Remove for Production
+5V
U26
D[7:0]
D7
D6
D5
D4
D3
D2
D1
D0
A
10
GND
11
12
13
14
15
16
17
18
O7
O6
O5
O4
O3
O2
O1
O0
20
VCC
+5VIN
74LVC541AD
I7
I6
I5
I4
I3
I2
I1
I0
OE2
OE1
9
8
7
6
5
4
3
2
R118
19
1
NS
CS1n
RDn
VOL_UP
VOL_DOWN
MUNE
P_UP
P_DOWN
TV_AV
POWER_ON(MUNE)
IR
STBLED
J10
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
Title
PW171-LGPDP
PH-14A
V33
C243 C244 C245 C246 C247 C248
0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF
5
Main (Video)
C249
0.1uF
4
Size
B
File
MISC
Date:
Drawn by:
3
2
Checked by:
Rev
C
Sheet
1
of
10
12
Approved by:
5
4
3
U12
C125
0.1uF
0.1uF
C126
0.1uF
C127
0.1uF
C128
0.1uF
C129
0.1uF
MA9
MA10
19
BA
LDQM
UDQM
DQM0
14
36
CLK_M
35
34
CLK
CKE
MWECASRASMCS-
15
16
17
18
WE
CAS
RAS
CS
1
25
VDD
VDD
7
13
38
44
VDDQ
VDDQ
VDDQ
VDDQ
V33N
V33N
C140
0.1uF
C141
0.1uF
C142
0.1uF
C143
0.1uF
C144
0.1uF
C145
0.1uF
C146
0.1uF
C147
0.1uF
V33N
2
3
5
6
8
9
11
12
39
40
42
43
45
46
48
49
NC
NC
33
37
MD0
MD1
MD2
MD3
MD4
MD5
MD6
MD7
MD8
MD9
MD10
MD11
MD12
MD13
MD14
MD15
MA0
MA1
MA2
MA3
MA4
MA5
MA6
MA7
MA8
MA9
MA10
DQM1
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
19
BA
14
36
LDQM
UDQM
CLK_M
35
34
CLK
CKE
MWECASRASMCS-
15
16
17
18
WE
CAS
RAS
CS
V33N
V33N
21
22
23
24
27
28
29
30
31
32
20
VSS
VSS
26
50
1
25
VDD
VDD
VSSQ
VSSQ
VSSQ
VSSQ
47
41
10
4
7
13
38
44
VDDQ
VDDQ
VDDQ
VDDQ
B
RESETn
SDA
SCL
NDSP_EN
V33N
R64
204
RESET
118
119
116
115
34
35
107
VSSQ
VSSQ
VSSQ
VSSQ
47
41
10
4
V33N
C113
0.1uF
X7R
0603
C130
0.1uF
X7R
0603
YQ0
YQ1
YQ2
YQ3
YQ4
YQ5
YQ6
YQ7
YQ8
YQ9
72
67
66
60
59
52
49
47
46
45
GRN_Y0
GRN_Y1
GRN_Y2
GRN_Y3
GRN_Y4
GRN_Y5
GRN_Y6
GRN_Y7
UQ0
UQ1
UQ2
UQ3
UQ4
UQ5
UQ6
UQ7
UQ8
UQ9
91
90
88
87
86
84
82
81
80
73
BLU_Cb0
BLU_Cb1
BLU_Cb2
BLU_Cb3
BLU_Cb4
BLU_Cb5
BLU_Cb6
BLU_Cb7
RP30
5
6
7
8
5
6
7
8
RP31
VQ0
VQ1
VQ2
VQ3
VQ4
VQ5
VQ6
VQ7
VQ8
VQ9
106
105
103
100
99
97
96
95
94
92
RED_Cr0
RED_Cr1
RED_Cr2
RED_Cr3
RED_Cr4
RED_Cr5
RED_Cr6
RED_Cr7
RP32
1
2
3
4
1
2
3
4
RP33
PCLK
VSQ
HSQ
HVQ
VBQ
DVQ
37
41
38
39
42
109
MA0
MA1
MA2
MA3
MA4
MA5
MA6
MA7
MA8
MA9
MA10
DQM0
DQM1
MWECASRASMCS-
124
123
122
120
33
32
30
29
125
26
127
21
137
136
135
129
128
51
50
68
77
75
CSA0
CSA1
I2C3W
SCS
SDA
SCL
TEST
RSET
VREFOUT
VREFIN
43
74
76
YA
RED-VDD
RED-GND
56
57
58
114
113
111
110
RFLOCK
APLLF
OEQ
P60
BYA
GRN-VDD
GRN-GND
63
64
65
132
XI
133
69
70
71
XO
RYA
BLU-VDD
BLU-GND
NV320XO
V33N
R66
C165
22pF
L27
VCC320P
+ C161
2M
C132
0.1uF
X7R
0603
C133
0.1uF
X7R
0603
C121
0.1uF
X7R
0603
C122
0.1uF
X7R
0603
C134
0.1uF
X7R
0603
C135
0.1uF
X7R
0603
C136
0.1uF
X7R
0603
C117
0.1uF
X7R
0603
C118
0.1uF
X7R
0603
C119
0.1uF
X7R
0603
C137
0.1uF
X7R
0603
C138
0.1uF
X7R
0603
C139
0.1uF
X7R
0603
D
+ C149
VG0
VG1
VG2
VG3
VG4
VG5
VG6
VG7
47R
4
3
2
1
4
3
2
1
47R
VB0
VB1
VB2
VB3
VB4
VB5
VB6
VB7
47R
8
7
6
5
8
7
6
5
47R
VR0
VR1
VR2
VR3
VR4
VR5
VR6
VR7
22uF
C150
0.1uF
U14
LM2937_TO263
VO 3
VI
V33N
+ C148
22uF
22uF
C
VB[7:0]
VB[7:0]
VR[7:0]
VR[7:0]
TPVCK
TPVS TPHS
VCLK
VVS
VHS
VPEN
R62 0
V33N
COMP320
+ C152
1uF
RSET320
C153
0.1uF
X7R
0603
B
R63 100
REF320
C155
0.1uF
X7R
0603
10uF
C162
0.1uF
X7R
0603
C163
0.1uF
X7R
0603
10uH
C164
0.1uF
X7R
0603
L28
VCC320A
+ C156
10uF
C157
0.1uF
X7R
0603
C158
0.1uF
X7R
0603
C159
0.1uF
X7R
0603
C160
0.1uF
X7R
0603
A
C166
22pF
Main (Video)
Title
PW171-LGPDP
Size
C
Date:
Drawn by:
5
+ C151
V33N
10uH
A
C131
0.1uF
X7R
0603
C120
0.1uF
X7R
0603
VG[7:0]
VG[7:0]
RP26 47R
4
3
2
1
1
2
3
4
47R
5
6
7
8
8
7
6
5
RP27
10uF
Y1
10.000MHZ
HC-49/SD
C116
0.1uF
X7R
0603
1
V33N
NV320XI
0
C115
0.1uF
X7R
0603
V33N
+ C154
R65
C114
0.1uF
X7R
0603
VCC
ADVDD
ADGND
COMP
DAC-VCC
DAC-GND
NV320
100
NO STUFF
26
50
DQM0
DQM1
WE
CAS
RAS
CS
ODD
VS
HS
HREF
CREF
LLC
HRC
LLAD2
HRA
CLV
HREFO
LLA
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
197
198
199
200
201
202
203
24
27
167
168
169
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
DQ24
DQ25
DQ26
DQ27
DQ28
DQ29
DQ30
DQ31
DVDLLC
DVDB
DVDHS
DVDVS
VSS
VSS
GND1
GND2
GND3
GND4
GND5
GND6
GND7
GND8
GND9
GND10
GND11
GND12
GND13
GND14
GND15
GND16
GND17
GND_CORE1
GND_CORE2
GND_CORE3
GND_CORE4
VVCLK
159
163
164
165
NC
NC
33
37
MD16
MD17
MD18
MD19
MD20
MD21
MD22
MD23
MD24
MD25
MD26
MD27
MD28
MD29
MD30
MD31
7
15
23
36
44
53
79
89
98
108
117
126
139
148
157
166
207
25
78
134
177
LLC320
V0
V1
V2
V3
V4
V5
V6
V7
101 GND_PLL1
205 GND_PLL2
161 GND_PLL3
VVVS
VVHS
189
190
191
192
193
194
195
196
102 VCC_PLL1
206 VCC_PLL2
160 VCC_PLL3
RP29 47R
U0
U1
U2
U3
U4
U5
U6
U7
VCC_CORE_1
VCC_CORE_2
VCC_CORE_3
VCC_CORE_4
VUV0
VUV1
VUV2
VUV3
VUV4
VUV5
VUV6
VUV7
180
181
183
184
185
186
187
188
28
85
131
182
VUV[7:0]
Y0
Y1
Y2
Y3
Y4
Y5
Y6
Y7
VCCIO_1
VCCIO_2
VCCIO_3
VCCIO_4
VCCIO_5
VCCIO_6
VCCIO_7
VCCIO_8
VCCIO_9
VCCIO_10
VCCIO_11
VCCIO_12
VCCIO_13
VCCIO_14
VCCIO_15
VCCIO_16
VCCIO_17
5
6
7
8
5
6
7
8
RP28 47R
4
3
2
1
4
3
2
1
171
172
173
174
175
176
178
179
3
11
19
31
40
48
61
83
93
104
112
121
130
144
153
162
170
C
VY0
VY1
VY2
VY3
VY4
VY5
VY6
VY7
9
8
6
5
4
2
1
208
20
18
17
16
14
13
12
10
147
146
145
143
142
141
140
138
158
156
155
154
152
151
150
149
U15
VY[7:0]
2
3
5
6
8
9
11
12
39
40
42
43
45
46
48
49
HY57V161610D-7
MD0
MD1
MD2
MD3
MD4
MD5
MD6
MD7
MD8
MD9
MD10
MD11
MD12
MD13
MD14
MD15
MD16
MD17
MD18
MD19
MD20
MD21
MD22
MD23
MD24
MD25
MD26
MD27
MD28
MD29
MD30
MD31
HY57V161610D-7
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
GND
D
C123
0.1uF
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ12
DQ13
DQ14
DQ15
2
V33N
C124
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
CLK_M
0.1uF
1
22
C112
21
22
23
24
27
28
29
30
31
32
20
CLK
MA0
MA1
MA2
MA3
MA4
MA5
MA6
MA7
MA8
VCC
2
U13
4
3
2
File
DEINTERLACE
Rev
C
Checked by:
1
Sheet
6
12
of
Approved by:
5
4
U27
LM317S
C251
0.1uF
+
0.1uF
1
+
C250
22uF
1
C253
VO
TAB
1
D
VI
ADJ
3
2
1
V25
4
VCC
3
2
R126
510
D
C252
22uF
2
2
C254
V25ADJ
1000uF-16V
R129
510
+5VIN
VCC
C
1
C
+
2
C259
220uF-16V
VCC
V33
C267
0.1uF
C269
0.1uF
1
ADJ
U29 LM3940IS-3.3
3 VI
VO 2
+
C268
22uF
B
2
1
B
C261
0.1uF C262
1000pF
Title
PW171-LGPDP
A
Main (Video)
5
4
3
Size
A
File
POWER
Date:
Drawn by:
A
Rev
C
Checked by:
2
Sheet
11
12
of
Approved by:
1
5
4
3
GFBK
GGE[7:0]
GBE[7:0]
C
GRO[7:0]
GGO[7:0]
GBO[7:0]
B
U26
V24
V23
V25
V26
W25
W24
W23
GGE0
GGE1
GGE2
GGE3
GGE4
GGE5
GGE6
GGE7
H23
G26
H25
P23
P24
P25
P26
R23
GBE0
GBE1
GBE2
GBE3
GBE4
GBE5
GBE6
GBE7
B25
A26
D24
E23
C25
B26
C26
E24
GBE0
GBE1
GBE2
GBE3
GBE4
GBE5
GBE6
GBE7
GRO0
GRO1
GRO2
GRO3
GRO4
GRO5
GRO6
GRO7
R24
R25
R26
T23
T24
T25
T26
U25
GRO0
GRO1
GRO2
GRO3
GRO4
GRO5
GRO6
GRO7
F23
D25
D26
F24
E25
E26
F25
F26
GGO0
GGO1
GGO2
GGO3
GGO4
GGO5
GGO6
GGO7
GBO0
GBO1
GBO2
GBO3
GBO4
GBO5
GBO6
GBO7
D21
B22
C22
A23
B23
D22
C23
A24
GBO0
GBO1
GBO2
GBO3
GBO4
GBO5
GBO6
GBO7
R80
R79
R78
R81
4.7K
4.7K
4.7K
4.7K
C171
R86
18pF
18pF
0
F4
WDTEN
D1
D2
RXD
TXD
E3
E2
IRRCVR0
IRRCVR1
C1
C2
B1
B2
D5
B3
A2
A3
PORTA0
PORTA1
PORTA2
PORTA3
PORTA4
PORTA5
PORTA6
PORTA7
C5
D6
B4
A4
C6
B5
A5
B6
PORTB0
PORTB1
PORTB2
PORTB3
PORTB4
PORTB5
PORTB6
PORTB7
A6
D8
C8
B7
A7
B8
D9
C9
PORTC0
PORTC1
PORTC2
PORTC3
PORTC4
PORTC5
PORTC6
PORTC7
PDWN
3WSCL
3WSDA
3WSLE
U18A
PW365
Graphics Port
VCLK
B16
VCLK
VPEN
B18
A21
B21
A22
C21
VPEN
VLAV
VVS
VHS
VFIELD
VVS
VHS
VFIELD
VR[7:0]
VG[7:0]
VB[7:0]
PW365
VR0
VR1
VR2
VR3
VR4
VR5
VR6
VR7
A9
B10
A10
D11
C11
B11
A11
D12
VR0
VR1
VR2
VR3
VR4
VR5
VR6
VR7
VG0
VG1
VG2
VG3
VG4
VG5
VG6
VG7
C12
B12
A12
B13
A13
D14
C14
B14
VG0
VG1
VG2
VG3
VG4
VG5
VG6
VG7
VB0
VB1
VB2
VB3
VB4
VB5
VB6
VB7
A14
D15
C15
B15
A15
D16
C16
A16
VB0
VB1
VB2
VB3
VB4
VB5
VB6
VB7
NDSP_EN
VGASEL
GAFEOE
ICSDAT
ICSCLK
ICSSTD
ICSSTM
R379
R378
U18B
4.7K
U18E
4.7K
R380
4.7K
MUTE
SLEEP1
PIO4
PIO5
VPPEN
V3P
PW365
Video Port
PC7
V3P V3P V3P
4.7K
4.7K
0
R387
R87
R85
R88
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
U2
V1
V2
W1
V3
V4
W3
W4
AA1
AB2
AA3
AC1
AB3
AD1
AE1
AD2
AB4
AC3
AF1
AE2
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
H3
H2
J4
J3
K1
K2
L1
L2
L3
L4
M3
M4
N1
N2
N3
N4
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
RD
WR
BHEN
ROMOE
ROMWE
RAMOE
RAMWE
CS0
CS1
CS2
CS3
EXTINT0
EXTINT1
EXTINT2
NMI
T3
T4
U1
R2
R1
P2
P1
R3
R4
T1
T2
G2
G1
H1
F1
CPUEN
RESET
CLKIN
MCKEXT
DCKEXT
UCSRC
XTALI
XTALO
B17
B9
AE4
AF2
CPUTMS
CPUTCLK
CPUTDI
CPUTDO
E4
AC5
A8
MODE0
MODE1
MODE2
U18D
PW365
Misc
D[15:0]
V3P
FB_11_OHM_500MA
V25
V25
V25
V25
V25
V25
V25
V25
V25
V25
C183
C184
C185
C186
C187
C188
C189
C190
C191 V25
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
V25
C202
C203
C204
22uF
0.1uF
0.1uF
Y25
AA26
AA25
AB26
AA24
AA23
AC26
AC25
RRE0 47R
RRE1
RRE2
RRE3
RRE4 47R
RRE5
RRE6
RRE7
RP34DRE0
DRE1
DRE2
DRE3
RP35DRE4
DRE5
DRE6
DRE7
DGE0
DGE1
DGE2
DGE3
DGE4
DGE5
DGE6
DGE7
AB23
AC24
AD26
AD23
AC22
AE24
AF25
AF24
RGE0 47R
RGE1
RGE2
RGE3
RGE4 47R
RGE5
RGE6
RGE7
RP36DGE0
DGE1
DGE2
DGE3
RP37DGE4
DGE5
DGE6
DGE7
DBE0
DBE1
DBE2
DBE3
DBE4
DBE5
DBE6
DBE7
AE23
AF23
AD21
AE22
AE19
AE18
AD18
AE17
RBE0 47R
RBE1
RBE2
RBE3
RBE4 47R
RBE5
RBE6
RBE7
RP38DBE0
DBE1
DBE2
DBE3
RP39DBE4
DBE5
DBE6
DBE7
DRO0
DRO1
DRO2
DRO3
DRO4
DRO5
DRO6
DRO7
AF13
AC12
AD12
AE12
AF12
AE11
AF11
AE10
RRO0 47R
RRO1
RRO2
RRO3
RRO4 47R
RRO5
RRO6
RRO7
RP40DRO0
DRO1
DRO2
DRO3
RP41DRO4
DRO5
DRO6
DRO7
DGO0
DGO1
DGO2
DGO3
DGO4
DGO5
DGO6
DGO7
AF10
AD9
AC9
AE9
AD8
AC8
AF8
AF7
RGO0 47R
RGO1
RGO2
RGO3
RGO4 47R
RGO5
RGO6
RGO7
RP42DGO0
DGO1
DGO2
DGO3
RP43DGO4
DGO5
DGO6
DGO7
DBO0
DBO1
DBO2
DBO3
DBO4
DBO5
DBO6
DBO7
AE7
AF6
AE6
AC6
AE5
AD5
AF4
AE3
RBO0 47R
RBO1
RBO2
RBO3
RBO4 47R
RBO5
RBO6
RBO7
RP44DBO0
DBO1
DBO2
DBO3
RP45DBO4
DBO5
DBO6
DBO7
U18C
ROMOEn
ROMWEn
R83 NS
R84
CS0N1
CS1n
CS2N1
CS3N1
VVINT
EINT1
EINT2
NMI
CS3n
EINT0
EINT1
EINT2
22uF
V25
DRE0
DRE1
DRE2
DRE3
DRE4
DRE5
DRE6
DRE7
Display Port
NS
C182
V25
RDK
RDn
CS0n
V25
V25
V25
R76
AD13
AD15
AC15
AF17
AC16
AD16
PW365
V25
Power and Ground
4
A[19:0]
47
DCLK
DVS
DHS
DENR
DENG
DENB
R89
10K
10K
V33
L30
GDFEOE
DTXON
MUTE
SLEEP1
in/ext
PC6
V25
V3P
V3P
V3P
DCLK
DVS
DHS
DENR
DENG
DENB
V3P
DRE[7:0]
D
DGE[7:0]
DBE[7:0]
C
DRO[7:0]
DBO[7:0]
B
V3P
C172
C173
C174
C175
C176
C177
C178
C179
C180
C181
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
V25 V25P
V25P
V3P
V3P
V3P
V3P
DGO[7:0]
V3P
V3P
C192
C193C194
C195
C196
C197
C198
C199
C200
C201
0.1uF
0.1uF22uF
0.1uF
22uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
A
A1 GND1
A17 GND2
A18 GND3
A19 GND4
B19 GND5
B20 GND6
B24 GND7
D4 GND8
D7 GND9
D10 GND10
D13 GND11
D17 GND12
D20 GND13
D23 GND14
G4 GND15
G23 GND16
H24 GND17
J2 GND18
K4 GND19
K23 GND20
M2 GND21
M23 GND22
N23 GND23
N25 GND24
P4 GND25
U4 GND26
U23 GND27
W26 GND28
Y1 GND29
D3 GND30
Y23 GND31
AA4 GND32
AB1 GND33
AB25 GND34
AC4 GND35
AC7 GND36
AC10GND37
AC11GND38
AC13GND39
AC14GND40
AC17GND41
AC18GND42
AC20GND43
AC23GND44
AD22GND45
AE14 GND46
AE20 GND47
AE25 GND48
AE26 GND49
AF3 GND50
AF5 GND51
AF9 GND52
AF16 GND53
AF20 GND54
AF21 GND55
AF22 GND56
5
WDTEN
RXD
TXD
SDA
SCL
PDWN
PA4
FB_11_OHM_500MA
VDD1
VDD2
VDD3
VDD4
VDD5
VDD6
VDD7
VDD8
VDD9
VDD10
VDD11
VDD12
VDD13
VDD14
VDD15
VDD16
VDD17
VDD18
C170 Y2
UCSRC
XTALI
XTALO
CLKIN1
PA3
V25P
A
MCKEXT
DCKEXT
F2
E1
Y2
AE15
AF15
F3
Y3
Y4
CLKIN
IRRCVR1
V25
L29
CPUEN
R77
XTAL14.31818
GGE0
GGE1
GGE2
GGE3
GGE4
GGE5
GGE6
GGE7
GGO0
GGO1
GGO2
GGO3
GGO4
GGO5
GGO6
GGO7
4.7K
RESET
GBLKSPL
GCOAST
GRE0
GRE1
GRE2
GRE3
GRE4
GRE5
GRE6
GRE7
A20
A25
C4
C7
C10
C17
C18
C19
C20
D18
D19
G3
G24
K3
K24
N26
U3
U24
V25
GRE0
GRE1
GRE2
GRE3
GRE4
GRE5
GRE6
GRE7
M25
H26
J25
J23
J24
M24
M26
C3
C13
C24
G25
H4
J1
M1
N24
P3
W2
Y26
AB24
AC2
AC21
AD3
AD6
AD11
AD14
AD24
AE8
AE13
AE16
GRE[7:0]
GCLKOUT
GFBK
GREF
GBLKSPL
GCOAST
GHSFOUT
GADCCLK
VCC1
VCC2
VCC3
VCC4
VCC5
VCC6
VCC7
VCC8
VCC9
VCC10
VCC11
VCC12
VCC13
VCC14
VCC15
VCC16
VCC17
VCC18
VCC19
VCC20
VCC21
VCC22
NS
GCLK
GPEN
GVS
GHS
GSOG
GFIELD
PLLCLK
Y24
AA2
AC19
AD4
AD7
AD10
AD17
AD19
AD20
AD25
AE21
AF14
AF18
AF19
AF26
D
1
V3P V3P V3P V3P V3P
L24
K26
L25
J26
R82 K25
L26
L23
VDD20
VDD21
VDD22
VDD23
VDD24
VDD25
VDD26
VDD27
VDD28
VDD29
VDD30
VDD31
VDD32
VDD33
VDD34
GCLK
GPEN
GVS
GHS
2
Title
PW171-LGPDP
Size
B
Main (Video)
3
File
PW171
Date:
Drawn by:
2
Checked by:
Rev
C
Sheet
1
of
8
12
Approved by:
5
4
3
2
1
V33L
L31
C207
330pF
D
DRE[7:0]
DGE[7:0]
DBE[7:0]
DRO[7:0]
DRO0
DRO1
DRO2
DRO3
DRO4
DRO5
DRO6
DRO7
DGO0
DGO1
DGO2
DGO3
DGO4
DGO5
DGO6
DGO7
DBO0
DBO1
DBO2
DBO3
DBO4
DBO5
DBO6
DBO7
V33L
C
R92
DGO[7:0]
R94
10K
NC
R95
R96
NU
10K
DRE0
DRE1
DRE2
DRE3
DRE4
DRE5
DRE6
DRE7
DGE0
DGE1
DGE2
DGE3
DGE4
DGE5
DGE6
DGE7
DBE0
DBE1
DBE2
DBE3
DBE4
DBE5
DBE6
DBE7
DBO[7:0]
DCLK
DENG
DHS
DVS
B
C208
330pF
C210
330pF
U20
LM2937_SOT223
0.1uF
2
C227
VO
TAB
GND
VI
4
1
97
96
95
94
93
92
91
90
6
5
4
3
2
1
100
99
16
15
14
13
12
11
10
9
DIE16
DIE17
DIE18
DIE19
DIE20
DIE21
DIE22
DIE23
DIE8
DIE9
DIE10
DIE11
DIE12
DIE13
DIE14
DIE15
DIE0
DIE1
DIE2
DIE3
DIE4
DIE5
DIE6
DIE7
55
54
53
52
51
50
49
48
65
64
63
62
61
60
59
58
75
74
73
72
71
70
69
68
DIO16
DIO17
DIO18
DIO19
DIO20
DIO21
DIO22
DIO23
DIO8
DIO9
DIO10
DIO11
DIO12
DIO13
DIO14
DIO15
DIO0
DIO1
DIO2
DIO3
DIO4
DIO5
DIO6
DIO7
80
78
76
77
84
83
82
24
25
IDCK
DE
HSYNC
VSYNC
CTL1
CTL2
CTL3
EDGE
PIXS
8
30
56
88
17
66
81
98
36
38
44
18
85
C216
330pF
47uF
C214
330pF
C205
1uF
C218
330pF
C219
C220
10uF
10uF
L33
C222
100pF
46
45
TX2+
TX2-
TX1+
TX1-
43
42
TX1+
TX1-
TX0+
TX0-
40
39
TX0+
TX0-
TXC+
TXC-
35
34
TXC+
TXC-
EXT_SWING
32
PD
26
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
20
21
22
23
27
28
29
87
GND
GND
GND
GND
GND
GND
AGND
AGND
AGND
AGND
PGND1
PGND2
7
31
57
67
79
89
33
37
41
47
19
86
TX2+
TX2-
C217
330pF
+ C223
10uF
C215
0.1uF
V33L
+ C224
22uF
200+ Ohm
C221
0.1uF
V33L
V33T
C225 200+ Ohm
0.1uF
C226
0.1uF
R90
R91
0
0
J6
25
R93
400
V33L
V33L
V33L
VCC
DENR
DENG
DENB
A
DCLK
DRE0
DRE1
DRE2
DRE3
DRE4
DRE5
DRE6
DRE7
DGE0
DGE1
DGE2
DGE3
DGE4
DGE5
DGE6
DGE7
DBE0
DBE1
DBE2
DBE3
DBE4
DBE5
DBE6
DBE7
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
49
51
53
55
57
59
61
63
65
67
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
54
56
58
60
62
64
66
68
DRO0
DRO1
DRO2
DRO3
DRO4
DRO5
DRO6
DRO7
DGO0
DGO1
DGO2
DGO3
DGO4
DGO5
DGO6
DGO7
DBO0
DBO1
DBO2
DBO3
DBO4
DBO5
DBO6
DBO7
4
C1
C2
C3
C4
C5
C6
26
A_RED
A_GREEN
A_BLUE
A_HSYNC
A_GND1
A_GND2
NC2
SHELL2
27
C
28
B
DGO[7:0]
DBO[7:0]
A
Title
PW171-LGPDP
Size
File
Custom
3
NC1
DATA2DATA2+
DATA2/4_SHLD
DATA4DATA4+
DDC_CLK
DDC_DATA
A_VSYNC
DATA1DATA1+
DATA1/3_SHLD
DATA3DATA3+
+5V
GND
H_PLUG_DET
DATA0DATA0+
DATA0/5_SHLD
DATA5DATA5+
CLK_SHLD
CLK+
CLK-
DRO[7:0]
Date:
Drawn by:
5
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
DHS
DVS
HDR_34X2
Main (Video)
SHELL1
DVI_V
JP4
DRE[7:0]
DBE[7:0]
0.1uF
C213
330pF
L32
V33L
C229
C212
330pF
D
VCC
VCC
VCC
VCC
IVCC
IVCC
IVCC
IVCC
AVCC
AVCC
AVCC
PVCC1
PVCC2
3
C228
C211
330pF
U19 Sil150
DGE[7:0]
VCC
C206
200+ Ohm
10uF
+
C209
330pF
2
Rev
C
TMDS OUTPUT
Checked by:
Sheet
1
9
12
of
Approved by:
4
3
R17
VCCV
3.3K
VVINT
VCCV
C280
U10
CCV2
R22
R25
C69
NC
33
R30
470
0.1uF
10
560pF
4
6
1
R32
VCCV
VDD
12
BOX
17
R20
8.2K
VIN INTRO
RED
HIN
GREEN
BLUE
VIDED
CSYNC
REF
LPF
SEN
SMS
ASEL
VSSA
18
2
3
R23
R26
R28
13K
13K
13K
10K
C74
C75
47uF
0.1uF
VCC
R18
22K
VCCR
Q1
R19
22K
VCCG
SDA
2
S
D
SDA5V
3
D
VCCB
8
SN7002
9
C286
R31
11
C287
6.8K
Z86229
C71
C72
C73
6.8nF
68nF
0.1uF
33pF
2K
R33
C285
33pF
2K
R34
2K
D15
C284
33pF
2K
1
2
33pF
V33
1N1183A
VCC
R36
R35
R37
22K
Q2
R38
22K
G
L19
FB_420_OHM_200MA
13
5
7
C70
+5VT
SCL
SDA
SDO
V33
220nF
VBOX
1
VVVS
VVHS
D
15
14
16
1
G
SCL5V
SDA5V
2
1
5
SCL
L20
CB
R39
75
3uH
R40
75
C77
2
S
D
SCL5V
3
VCBIN
C76
220nF
SN7002
330pF
D16
1
VVPA
2
1N1183A
3
1
+5VIN
+5VT
A
C89
680nF
VDOEn
V33
R50
10K
+5V
R54 51K
XTAL_20.25
VTV
RESETn
C91
18pF
IR
in/ext
STBLED
MUTE
POWER_ON
SLEEP1
V33
C101
0.1uF
V33
C102
0.1uF
VCC
V33
C103
0.1uF
R60
R61
SCL
SDA
VAAV
C105
22uF
4
5
6
B2/CB2IN
G2/Y2IN
R2/CR2IN
71
72
73
74
75
CIN
VIN1
VIN2
VIN3
VIN4
17
VGAV
18
YCOEQ
15
RESQ
13
14
SCL
SDA
62
63
XTAL1
XTAL2
67
I2CSEL
16
TEST
8
61
NC1
NC2
9
C97
0.1uF
C98
0.1uF
59
69
76
LLC1
LLC2
28
27
VLLC1
Y7
Y6
Y5
Y4
Y3
Y2
Y1
Y0
31
32
33
34
37
38
39
40
VVY7
VVY6
VVY5
VVY4
VVY3
VVY2
VVY1
VVY0
RP22
47R
RP23
47R
C7
C6
C5
C4
C3
C2
C1
C0
41
42
43
44
47
48
49
50
VVUV7
VVUV6
VVUV5
VVUV4
VVUV3
VVUV2
VVUV1
VVUV0
RP24
47R
RP25
47R
FFOE
FFRE
FFRSTW
FFWE
FFIE
23
22
21
20
19
FSY/HC
FPDAT
CLK20
CLK5
55
58
24
60
VOUT
VREF
VRT
70
78
66
VPC3230D_C5
VSUPCAP
VVGCAP
47R
53
57
56
54
U11
VVSCAP
0
0
L26
FB_420_OHM_200MA
C104
0.1uF
C92
18pF
FB1IN
B1/CB1IN
G1/Y1IN
R1/CR1IN
VSTBY
VSUPF
VSUPAI
10
26
29
36
45
52
680nF
Z1
V33
C100
0.1uF
C87
VVIN3
R53
0
CON19
V33
680nF
VX1
VX2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
J4
C88
R49
75
6
5
S+AV
VCVID
L24
3uH
R48
75
680nF
VVIN1
1nF
3uH L25
LUMA
R47
75
C85
79
1
2
3
RP21
INTLC
VS
MSY/HS
AVO
47
VFIELD
VVVS
VVHS
R45
VVCLK
VY[7:0]
VY7
VY6
VY5
VY4
VY3
VY2
VY1
VY0
VUV[7:0]
VUV7
VUV6
VUV5
VUV4
VUV3
VUV2
VUV1
VUV0
B
VAAV
R51
2K
C90
VVREF
VVRT
C93
0.1uF
R52
47
3
7
4
2
B
3uH
CHROM
4
2
3
1
VCHROMA
C86
220nF
220nF
220nF
VBOX
VCCB
VCCG
VCCR
330pF
VLUMA
L23
C81
C82
C83
C84
C
R55
470
4.7uF
Q3
3904
1
C94
22uF
C95
0.1uF
C96
22uF
R57
2K
R58
470
VVGPA
C99
0.1uF
A
VAAV
C106
0.1uF
VAAV
C107
0.1uF
VAAV
C108
0.1uF
VAAV
C109
0.1uF
VAAV
C110
0.1uF
VAAV
Title
PW171-LGPDP
Main (Video)
C111
0.1uF
Size
File
CustomVIDEO INPUT
Date:
Drawn by:
5
CCV2
2
3uH
CVID
8
VCRIN
VAAV
VSUPD
VSUPPA
VSUPLLC
VSUPY
VSUPC
VSUPSY
R43
75
R44
75
J3
C80
220nF
V33
330pF
L22
CR
C79
VYIN
ASGF1
ASGF2
GNDY
GNDF
GNDAI
GNDC
GNDSY
ISGND
AISGND
R42
75
C78
220nF
7
64
35
65
77
46
51
68
80
R41
75
3uH
12
25
30
11
Y
GNDCAP
GNDPA
GNDLLC
GNDD1
L21
C
4
3
2
Rev
C
Checked by:
1
Sheet
of
5
12
Approved by:
5
4
3
02_INPUT
OUTA
OUTB
AUDIO OUTL
AUDIO OUTB
SIF
SDA5V
SCL5V
SDA
D
C
2
1
03_AUDIO
IR
MUTE
MUTE1
POWER_ON
SCL
SIF
SCL5V
SDA5V
AUDIO OUTL
AUDIO OUTR
D
C
02_INPUT
03_AUDIO
04_MCU+AMP
POWER_ON
RELAY
MUTE
OUTA
OUTB
MUTE1
IR
B
B
04_MCU+AMP
A
A
5
4
3
2
1
"U3(UVS7305M.FH)
only for the Model with Turner"
Audio/Tuner
Audio/Tuner
"U8(TDA9850)
only for the Model with Turner"
Audio/Tuner
Keypad
Remote control receiver
External L/R Speakers
Remote control
Basic Operations & Circuit Description
MODULE
There are 1 pc. panel and 8 pc.s PCB including 2 pc.s Y/Z Sustainer board, 2 pc.s Y Drive
board, 2 pc.s X (left and right) Extension PCB, 1 pc. Control (Signal Input) and 1 pc. Power
board in the Module.
SET
There are 5 pc.s PCBs including 1 pc. Tuner/Audio board, 1 pc. Keypad board, 1 pc.
Remote Control Receiver board, 1 pc. L/R Speakers and 1 pc. Main (Video) board in the SET.
Parts position
Internal Speaker (Right)
Power Supply
Internal Speaker (Left)
Y-Drive Top
Z-Sustainer
Y-Sustainer
External Speaker Terminals
Y-Drive Bottom
Power SW
X left Extension
EMI filter + AC Inlet
only for the Model with Turner
Remote control Receiver
Local key
Main (Video)
Stand
Tuner/Audio
Control (Signal Input)
X right Extension
PCB function
1. Power:
(1). Input voltage: AC 110V~240V, 47Hz~63Hz.
Input range: AC 90V(Min)~265V(Max) auto regulation.
(2). To provide power for PCBs.
2. Main (Video InterFace) board: To converter TV signals, S signals, AV signals, Y Pb/
Cb Pr/Cr signals, DVI signals and D-SUB signals to digital ones and to transmit to
Control board.
3. Control board: Dealing with the digital signal for output to panel.
4. Y-Sustainer / Z-Sustainer board:
(1). Receiving the signals from Control and high voltage supply.
(2). Output scanning waveform for Module.
5. Y-Drive board: Receive signal from Y sustainer, output horizontal scanning waveform to the panel.
6. X (left and right) extension board: Output addressing signals.
: Amplifying the audio signal to the internal or external speakers
7. Tuner/Audio Board:
of which selected.
PCB failure analysis
1. CONTROL: a. Abnormal noise on screen. b. No picture.
2. MAIN (VIDEO): a. Lacking color, Bad color scale.
b. No voice.
c. No picture but with signals output, OSD and back light.
d. Abnormal noise on screen.
3. POWER: No picture, no power output.
4. Z - Sustainer: a. No picture.
b. Color not enough.
c. Flash on screen.
5. Y - Sustainer: Darker picture with signals.
6. Audio Bard: a. No voice. (Make sure status: Mute / Internal, External speaker)
b. Noise
7. Y/Z - Sustainer: The component working temperature is about 55oC.
If the temperature rises abnormal, this may be a error point.
Basic operation of Plasma Display
1. After turning on power switch, power board sends 5Vst-by Volt to Micro Processor
IC waiting for ON signals from Key Switch or Remote Receiver.
2. When the ON signal from Key Switch or Remote Receiver is detected, Micro Processor
will send ON Control signals to Power. Then Power sends (5Vsc, 9Vsc, 24V and RLY
ON, Vs ON) to PCBs working. This time VIF will send signals to display back light,
OSD on the panel and start to search available signal sources. If the audio signals
input, them will be amplified by Audio AMP and transmitted to Speakers.
3. If some abnormal signals are detected (for example: over volts, over current, over
temperature and under volts), the system will be shut down by Power off.
Main IC Specifications
-
PW171 Image Processor
AD9883A 110MSPS/140MSPS Analog Interface for Flat Panel Displays
NV320 Video Enhancement Processor
VCP 323XD comb Filter Video Processor
SiI161B Panel Link Receiver
Z86229 NTSC Line 21 CCD Decoder
TDA9850 BTSC stereo/SAP decoder(only for the Model with Turner)
NJW1144 Audio Processor
Product Specification:
PW171 ImageProcessor
XGA/SXGA/UXGA Flat Panel Display Controller IC
P r e li m i n a r y
d to result in a personal injury or loss of life. Customers using or selling Pixelworks devices for use in such
applications do so at their ris
General Description
PW171 is a highly integrated “system-on-a-chip” that interfaces
analog, digital, and video inputs in virtually any format to a flat panel
monitor or multimedia display. PW171 is pin-compatible with the
PW364.
An embedded SDRAM frame buffer and memory controller perform
frame rate conversion. Computer images from VGA to UXGA at
almost any refresh rate can be resized to fit on a fixed-frequency
target display device with any resolution up to UXGA with full 24-bit
color.
PW171 includes advanced second-generation image scaling that
provides completely programmable, horizontal and vertical image
scaling.
PW171 also includes advanced second-generation sync decoding
which provides full support for a wide variety of sync types. This
includes interlaced, progressive, sync-on-green, and TMDS DE (Data
Enable) only.
PW171 ImageProcessor supports NTSC or PAL video data with a 4:3
aspect ratio and 16:9 aspect ratio sources, such as DVD or HDTV.
Nonlinear scaling and separate horizontal and vertical scalers allow
these inputs to be resized optimally for the native resolution and
aspect ratio of the display device.
PW171 uses an integrated PLL to synchronize the display interface
timing to the input timing. This requires only a single external crystal
to generate all necessary clocks for the system.
An integrated OSD controller provides bit-mapped based OSDs with
16 colors from a 64K color palette. The OSD controller supports
transparent and translucent functions.
PW171 provides a Pulse Width Modulation (PWM) output for low cost
backlight or audio control.
With reference source code and an on-chip microprocessor,
manufacturers can develop feature-rich products with rapid time-tomarket. Programmable features include the user interface, custom
start-up screen, all automatic imaging features, and special screen
effects.
PW171 incorporates new features while maintaining backward
compatibility with the PW264 and PW364 ImageProcessors.
Features
!Second-generation Image Scaling
!Second-generation Automatic Image Optimization
!Color Space Converter for graphics inputs
!Video processing
!Picture-In-Picture (PIP)
!Frame rate conversion
!Color matrix for improved color temperature adjustment
!On-board PLLs to generate MCLK and DCLK
!On-screen display
!On-chip microprocessor
!JTAG debugging port
!8-bit, 9-bit, or 10-bit display outputs
!24-bit CPU Addressing
!Hardware 2-Wire serial bus support
!Hardware PWM output
Applications
!LCD Monitors
!Plasma Displays
!Multimedia Displays
a
110 MSPS/140 MSPS Analog Interface
for Flat Panel Displays
AD9883A
FEATURES
140 MSPS Maximum Conversion Rate
300 MHz Analog Bandwidth
0.5 V to 1.0 V Analog Input Range
500 ps p-p PLL Clock Jitter at 110 MSPS
3.3 V Power Supply
Full Sync Processing
Sync Detect for “Hot Plugging”
Midscale Clamping
Power-Down Mode
Low Power: 500 mW Typical
4:2:2 Output Format Mode
FUNCTIONAL BLOCK DIAGRAM
RAIN
CLAMP
A/D
GAIN
CLAMP
A/D
BAIN
CLAMP
A/D
GENERAL DESCRIPTION
The AD9883A is a complete 8-bit, 140 MSPS monolithic analog
interface optimized for capturing RGB graphics signals from
personal computers and workstations. Its 140 MSPS encode
rate capability and full power analog bandwidth of 300 MHz
supports resolutions up to SXGA (1280 × 1024 at 75 Hz).
The AD9883A includes a 140 MHz triple ADC with internal
1.25 V reference, a PLL, and programmable gain, offset, and
clamp control. The user provides only a 3.3 V power supply,
analog input, and Hsync and COAST signals. Three-state
CMOS outputs may be powered from 2.5 V to 3.3 V.
The AD9883A’s on-chip PLL generates a pixel clock from the
Hsync input. Pixel clock output frequencies range from 12 MHz to
8
8
ROUTA
GOUTA
BOUTA
MIDSCV
HSYNC
APPLICATIONS
RGB Graphics Processing
LCD Monitors and Projectors
Plasma Display Panels
Scan Converters
Microdisplays
Digital TV
8
COAST
CLAMP
DTACK
SYNC
PROCESSING
AND CLOCK
GENERATION
HSOUT
VSOUT
SOGOUT
FILT
REF
SCL
SDA
A0
SERIAL REGISTER
AND
POWER MANAGEMENT
REF
BYPASS
AD9883A
140 MHz. PLL clock jitter is 500 ps p-p typical at 140 MSPS.
When the COAST signal is presented, the PLL maintains its
output frequency in the absence of Hsync. A sampling phase
adjustment is provided. Data, Hsync, and clock output phase
relationships are maintained. The AD9883A also offers full sync
processing for composite sync and sync-on-green applications.
A clamp signal is generated internally or may be provided by
the user through the CLAMP input pin. This interface is fully
programmable via a 2-wire serial interface.
Fabricated in an advanced CMOS process, the AD9883A is
provided in a space-saving 80-lead LQFP surface-mount plastic
package and is specified over the 0°C to 70°C temperature range.
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel:
Fax:
nD S P C o r po r a t io n
NV 3 2 0 D a ta S he et
NV320 Video Enhancement Processor
1.0 Introduction
The NV320 is a single-chip, programmable
video display processor providing advanced
features for progressive scan, high frame-rate
TV. The NV320 improves upon the functionality of the NV320P by handling non-standard
video input signals. Other feature enhancements include DCTI, Black Level Stretch, and
Saturation Control.
The NV320 offers the following features.
1.1 Highly Integrated Video Processor
• Three, on-chip, 10-bit Digital-to-Analog
•
•
•
•
Converters (DACs)
Built-in memory controller supporting
SDRAM or SGRAM
0.35µ CMOS process
3.3V power supply with 5V tolerant I/Os
Standard 208-pin PQFP
1.2 Video Input
• Multiple video input modes
- Data acquisition mode
- Line-locked mode
- DVD mode
• Multiple video input data formats
- Digital 16-bit YUV (4:2:2) or 12-bit YUV
(4:1:1)
- Digital 8-bit YUV (ITU-R 656)
- Digital 24-bit YUV (4:4:4)
1.3 Noise Reduction
• Motion adaptive noise reduction filter
1.4 Color Processing
• Built-in color space conversion
• Selectable output color space: YUV or
RGB
1.5 Video Processing
•
•
•
•
•
Advanced, non-linear video processing
Motion compensated deinterlacing
Programmable peaking
Non-linear interpolation
Background coloring
• Anti-flickering circuitry
• NTSC/PAL to SDTV 480p format conver•
•
•
•
sion
Frame rate up-conversion (50Hz up to
75Hz for PAL, 60Hz up to 90Hz for NTSC)
DCTI (Digital Color Transient Improvement)
Black Level Stretch
Saturation Control
1.6 Host Interface
• I2C interface
• No programming needed for default mode
application
1.7 General Description and Applications
The NV320 is a single chip digital video processor for progressive and digital TV applications. It provides high quality video
processing including video noise reduction,
motion compensation, sharpness enhancement, and resolution enhancement. It also
provides frame rate conversion and progressive scan conversion with deinterlacing.
The NV320 is a CMOS mixed signal circuit
highly integrated with three, 10-bit digital-toanalog converters controlled by the I2C interface. The NV320 accepts 16-bit YUV (4:2:2),
12-bit YUV (4:1:1), and 8-bit YUV (ITU-R 656)
simultaneously, or it accepts 24-bit YUV
(4:4:4) input from a front-end digital video
color decoder or from an analog-to-digital
converter. Additionally, NV320 supports multiple video input modes: acquisition mode, linelocked mode, and DVD mode.
The NV320 has an on-chip detection logic
block that corrects non-standard input signals
before processing.
Applications for the NV320 chip are listed
here.
• Progressive scan televisions
• Digital televisions (the chip is DTV/HDTV
ready)
nD S P C o r po r a t io n
NV 3 2 0 D a ta S he et
• Internet televisions
• Home theater and multimedia televisions
• Video conferencing
2.0 Ordering Information
Part
Number
NV320
Package
PQFP 208
Description
Plastic quad flat package, 208 leads
Version
1.0
3.0 Block Diagram of NV320
8-bit YUV
ITU R-656
Input Video
Selector
&
Formatter
Digital
YUV/RGB
nDSP
Video
Enhancement
Processor
10-Bit DAC
Y/G
10-Bit DAC
U/B
10-Bit DAC
V/R
LLC
LLAD2
HS/CLP
VS
Timing
PCLK
Controller
LLA
CLV
HREFO
Memory
Controller
SCL
SDA
Timing
HSQ
HBQ
Generator
Host
Interface
VSQ
VBQ
SDRAM/SGRAM
Interface
Figure 1. Block Diagram of NV320
VPC 323xD
Comb Filter Video Processor
1. Introduction
The VPC 323xD is a high-quality, single-chip video front-end, which is targeted for 4:3 and
16:9. 50/60 Hz and 100/120 Hz TV sets. It can be combined with other members of the
DIGIT3000 IC family (such as DDP 331x) and/or it can be used with 3rd-party products.
The main features of the VPC 323xD are
- High-performance adaptive 4H comb filter Y/C separator with adjustable vertical peaking.
- Multi-standard color decoder PAL/NTSC/SECAM including all substandards.
- Four CVBS, one S-VHS input, one CVBS output.
- Two RGB/YCrCb component inputs, one Fast Blank (FB) input.
- Integrated high-quality A/D converters and associated clamp and AGC circuits.
- Multi-standard sync processing.
- Linear horizontal scaling (0.25......4), as well as nonlinear horizontal scaling 'Panoramavision'.
- PAL+ preprocessing.
- Line-locked clock, data and sync, or 656-output interface.
- Peaking, contrast, brightness, color saturation and tint for RGB/YCrCb and CVBS/S-VHS.
- High-quality soft mixer controlled by Fast Blank.
- PIP processing for four picture sizes (1/4, 1/9, 1/16, or 1/36 of normal size) with 8-bit
resolution.
- Control interface for external field memory.
- I2C-bus interface.
- One 20.25-MHz crystal, few external components.
- 80-pin PQFP package.
®
SiI 161B PanelLink Receiver
Data Sheet
August 2002
General Description
Features
The SiI 161B receiver uses PanelLink Digital
technology to support high-resolution displays up to
UXGA (25-165MHz). This receiver supports up to true
color panels (24 bits per pixel, 16M colors) with both
one and two pixels per clock.
•
All PanelLink products are designed on a scaleable
CMOS architecture, ensuring support for future
performance enhancements while maintaining the
same logical interface. System designers can be
assured that the interface will be stable through a
number of technology and performance generations.
PanelLink Digital technology simplifies PC and display
interface design by resolving many of the system level
issues associated with high-speed mixed signal design,
providing the system designer with a digital interface
solution that is quicker to market and lower in cost.
•
•
•
•
•
•
•
•
•
Low Power Operation: 280mA max. current
consumption at 3.3V core operation
Time staggered data output for reduced ground
bounce and lower EMI
Sync Detect feature for Plug & Display
Cable Distance Support: over 5m with twistedpair, fiber-optics ready
ESD tolerant to 5kV (HBM on all pins)
Compliant with DVI 1.0 (DVI is backwards
®
TM
TM
compatible with VESA P&D , FPDI-2 and
DFP)
HSYNC de-jitter circuitry enables stable operation
even when HSYNC contains jitter
Low power standby mode
Automatic entry into standby mode with clock
detect circuitry
Standard and Pb-free packages (see page 25).
4'.+/+0#4; 41&7%6#2'%+(+%#6+10
<
+0'
'%1&'4
!"
•
Preprogrammed to Provide Full Compliance with
EIA–608 Specifications for Extended Data Services
Minimal Communications and Control Overhead Provide Simple Implementation of Violence Blocking,
Closed Captioning, and Auto Clock Set Features
•
Automatic Extraction and Serial Output of Special
XDS Packets (Time of Day, Local Time Zone, and
Program Blocking)
Programmable, On-Screen Display (OSD) for Creating Full Screen OSD or Captions inside a Picture-inPicture (PiP) Window
•
User-Programmable Horizontal Display Position for
easy OSD Centering and Adjustment
•
•
I2C Serial Data and Control Communication
•
Complete Stand-Alone Line 21 Decoder for ClosedCaptioned and Extended Data Services (XDS)
•
•
•
•
#$
%
&%
"
'
Programmable XDS Filter for a Specific XDS Packet
Cost-Effective Solution for NTSC Violence Blocking
inside Picture-in-Picture (PiP) Windows
Supports 2 Selectable I2C Addresses
Capable of processing Vertical Blanking Interval (VBI)
data from both fields of the video frame in data, the Z86229
Line 21 Decoder offers a feature-rich solution for any television or set-top application. The robust nature of the
Z86229 helps the device conform to the transmission format
defined in the Television Decoder Circuits Act of 1990, and
in accordance with the Electronics Industry Association
specification 608 (EIA–608).
The Line 21 data stream can consist of data from several data
channels multiplexed together. Field 1 consists of four data
channels: two Captions and two Texts. Field 2 consists of
five additional data channels: two Captions, two Texts, and
Extended Data Services (XDS). The XDS data structure is
defined in EIA–608. The Z86229 can recover and display
data transmitted on any of these nine data channels.
The Z86229 can recover and output to a host processor via
the I2C serial bus. The recovered XDS data packet is further
defined in the EIA–608 specification. The on-chip XDS filters in the Z86229 are fully programmable, enabling recovery of only those XDS data packets selected by the user. This
functionality allows the device to extract the required XDS
information with proper XDS filter setup for compatibility
in a variety of TVs, VCRs, and Set-Top boxes.
In addition, the Z86229 is ideally suited to monitor Line 21
video displayed in a PiP window for violence blocking,
CCD, and other XDS data services. A block diagram of the
Z86229 is illustrated in Figure 1.
I2C-bus controlled BTSC stereo/SAP decoder
TDA9850
FEATURES
- Quasi alignment-free application due to automatic adjustment of channel separation via
I2C-bus
- Dbx noise reduction circuit
- Dbx decoded stereo, Second Audio Program (SAP) or mono selectable at the AF outputs
- Additional SAP output without dbx, including de-emphasis
- High integration level with automatically tuned integrated filters
- Input level adjustment I2C-bus controlled
- Alignment-free SAP processing
- Stereo pilot PLL circuit with ceramic resonator, automatic adjustment procedure for
stereo channel separation, two pilot thresholds selectable via I2C-bus
- Automatic pilot cancellation
- Composite input noise detector with I2C-bus selectable thresholds for stereo and SAP off
- I2C-bus transceiver.
NJW1144
AUDIO PROCESSOR
GENERAL DESCRIPTION
The NJW1144 is a sound processor includes all of the functions required to process the
audio signal for TV, such as tone control, balance, volume, mute, and AGC functions.
Also the NJW1144 performs BBE sound enhancement and SRS 3D Stereo. The BBE
regenerates high definitive and nearly real sound, and SRS 3D Stereo regenerates 3D surround sound with only two speakers.
All of the internal stats and variables are controlled by I2C BUS interface.
FEATURES
- Operating Voltage
- I2C BUS Interface
8 to 13V
- BBE Sound Enhancement (Low Boost and High Boost: 15dB max.)
- Internal 6 Input Audio Selectors and Monitor Output
- The AGC circuit reduces volume difference among input sources.
- Variable AGC Compression Level via I2C (4-levels)
- SRS 3D Stereo and Simulated Stereo
- Variable Surround Effect Level via I2C
- Low Noise VCA
- Bi-CMOS Technology
- Package Outline
SOP40
0. Warnings and Cautions
9 WARNING indicates hazards that may lead to death or injury if ignored.
9 CAUTION indicates hazards that may lead to injury or damage to property if ignored.
WARNING
1)
This product uses a high voltage (450 V max.). Do not touch the circuitry of this product with your hands when
power is supplied to the product or immediately after turning off the power. Be sure to confirm that the voltage
is dropped to a sufficiently low level.
2)
Do not supply a voltage higher than that specified to this product. This may damage the product and may cause a
fire.
3)
Do not use this product in locations where the humidity is extremely high, where it may be splashed with water,
or where flammable materials surround it. Do not install or use the product in a location that does no satisfy the
specified environmental conditions. This may damage the product and may cause a fire.
4)
If a foreign substance (such as water, metal, or liquid) gets inside the product, immediately turn off the power.
Continuing to use the products it may cause fire or electric shock.
5)
If the product emits smoke, an abnormal smell, or makes an abnormal sound, immediately turn off the power. If
noting is displayed or if the display goes out during use, immediately turn off the power. Continuing to use the
product as it is may cause fire or electric shock.
6)
Do not disconnect or connect the connector while power to the product is on. It takes some time for the voltage
to drop to a sufficiently low level after the power has been turned off. Confirm that the voltage has dropped to a
safe level before disconnecting or connecting the connector. Otherwise, this may cause fire, electric shock, or
malfunction.
7)
Do not pull out or insert the power cable from/to an outlet with wet hands. It may cause electric shock.
8)
Do not damage or modify the power cable. It may cause fire or electric shock.
9)
If the power cable is damaged, or if the connector is loose, do not use the product; otherwise, this can lead to fire
or electric shock.
10)
If the power connector or the connector of the power cable becomes dirty or dusty, wipe it with a dry cloth.
Otherwise, this can lead to fire.
CAUTION
General
1)
Do not place this product in a location that is subject to heavy vibration, or on an unstable surface such as an
inclined surface. The product may fall off or fall over, causing injuries.
2)
When moving the product, be sure to turn off the power and disconnect all the cables. While moving the
product, watch your step. The product may be dropped or fall, leading to injuries of electric shock.
3)
Do not place this product in a location that is subject to heavy vibration, or on an unstable surface such as an
inclined surface. The product may fall off or fall over, causing injuries.
4)
Before disconnecting cable from the product, be sure to turn off the power. Be sure to hold the connector when
disconnecting cables. Pulling a cable with excessive force may cause the core of the cable to be exposed or
break the cable, and this can lead to fire or electric shock.
5)
This product should be moved by two or more persons. If one person attempts to carry this product alone, he/she
may be injured.
6)
This product contains glass. The glass may break, causing injuries, if shock, vibration, heat, or distortion is
applied to the product.
7)
The temperature of the glass surface of the display may rise to 80°C or more depending on the conditions of use.
If you touch the glass inadvertently, you may be burned.
8)
Do not poke or strike the glass surface of the display with a hard object. The glass may break or be scratched. If
the glass breaks, you may be injured.
9)
If you glass surface of the display breaks or is scratched, do not touch the broken pieces or the scratches with
bare hands. You may be injured.
10)
Do not place an object on the glass surface of the display. The glass may break or be scratched.
USE
1)
Because this product uses a high voltage, connecting or disconnecting the connectors while power is supplied to
the product may cause malfunctioning. Never connect or disconnect the connectors while the power is on.
Immediately after power has been turned off, a residual voltage remains in the product. Be sure to confirm that
the voltage has dropped to a sufficiently low level.
2)
Watching the display for a long time can tire the eyes. Take a break at appropriate intervals.
3)
PDP ’s brightness and contrast ratio is lower than that of the CRT. The picture is dimmer with surrounding light
and better for viewing in dark condition.
4)
Do not cover or wrap the product with a cloth or other covering while power is supplied to the product.
5)
Before turning on power to the product, check the wiring of the product and confirm that the supply voltage is
within the rated voltage range. If the wiring is wrong or if a voltage outside the rated range is applied, the
product may malfunction or be damaged.
6)
Do not store this product in a location where temperature and humidity are high. This may cause the product to
malfunction. Because this product uses a discharge phenomenon, it may take time to light (operation may be
delayed) when the product is used after it has been stored for a long time. In this case, it is recommended to light
all cells for about 2hours (aging).
7)
If the glass surface of the display becomes dirty, wipe it with a soft cloth moistened with a neutral detergent. Do
not use acidic or alkaline liquids, or organic solvents.
8)
Do not tilt or turn upside down while the module package is carried, the product may be damaged.
9)
This product is made from various materials such as glass, metal, and plastic. When discarding it, be sure to
contact a professional waste disposal operator.
Repair and Maintenance
Because this product combines the display panel and driver circuits in a single module, it cannot be repaired or
maintained at user’s office or plant. Arrangements for maintenance and repair will be determined later
1. GENERAL DESCRIPTION
DESCRIPTION
The PDP42V6#### is a 42-inch 16:9 color plasma display module with resolution of 852(H) × 480(V) pixels.
This is the display device which offers vivid colors with adopting AC plasma technology by LG Electronics Inc.
FEARURES
High peak brightness (1000cd/m2 Typical) and high contrast ratio (3000:1 Typical) enables user to create
high performance PDP SETs.
APPLICATIONS
9 Public information display
9 Video conference systems
9 Education and training systems
ELECTRICAL INTERFACE OF PLASMA DISPLAY
The PDP42V6#### requires only 8bits of digital video signals for each RGB color.
In addition to the video signals, six different DC voltages are required to operate the display.
The PDP42V6#### is equipped with P-CUBE function which analyzes display signals to optimize system
control factor for showing the best display performance.
GENERAL SPECFICATIONS
9 Model Name
9 Number of Pixels
9 Pixel Pitch
9 Cell Pitch
9 Display Area
9 Outline Dimension
9 Pixel Type
9 Number of Gradations
9 Weight
9 Aspect Ratio
9 Peak Brightness
9 Contrast Ratio
9 Power Consumption
9 Life-time
: PDP42V6#### (42V6#### Model)
: 852(H) × 480(V) (1pixel=3 RGB cells)
: 1080㎛ (H) × 1080㎛ (V)
: 367㎛ (H) × 1080㎛ (V) (Green Cell basis)
: 920.1(H) × 518.4(V) ±0.5mm
: 1005(H) × 597(V) × 61(D)±1mm
: RGB Closed type
: (R)256 × (G)256 × (B)256 (16.7 Mega colors)
: 14.8 Kg ± 0.5 Kg (Net 1EA)
111 Kg ± 5 Kg (5EA/1BOX)
: 16:9
: Typical 1000cd/㎡ (1/25 White Window)
: Average 60:1 (In a bright room with 150Lux at center)
: Typical 3000:1 (In a dark room 1/25 White Window pattern at center)
: Typical 220 W (Full White)
: more than 60,000 Hours of continuous operation
☞ Life-time is defined as the time when the brightness level becomes half of its initial value.
9 Display Dot Diagram
1st
pixel
column
Pixel Pitch(width)
2nd
pixel
column
Cell pitch
1.080㎜
851th
pixel
column
R:0.338㎜
G:0.367㎜
B:0.374㎜
852th
pixel
column
cell
R G B R G B
R G B R G B
R G B R G B
R G B R G B
479th pixel
row
R G B R G B
R G B R G B
480th pixel
row
R G B R G B
R G B R G B
3rd pixel
row
1.080㎜
R G B R G B
pitch(height)
R G B R G B
1st pixel
row
2nd pixel
row
pixel
7. CONNECTORS and CONNECTIONS
Power Input Connector
¾ Connector P3001 Pin Assignment
Pin No.
Symbol
Pin No.
Symbol
1
Vs
5
GND
2
Vs
6
Va
3
nc
7
GND
4
GND
8
+5V
8
7
6
5
4
3
2
1
1-1123723-8 Pin numbers
(Top View, viewed from the pin connection side)
9 Module side connector : 1-1123723-8 (Header)
9 Mating Connector
: 1-1123722-8 (Housing)
9 Connector Supplier
: AMP
Pin No.
Symbol
Pin No.
Symbol
1
VS
6
GND
2
VS
7
GND
3
VS
8
GND
4
nc
9
nc
5
GND
10
nc
9 Mating Connector
: 1-1123722 –10 (Housing)
: AMP
10
9
8
7
6
5
4
3
2
1
Pin No.
Symbol
Pin No.
Symbol
1
GND
3
5V
2
GND
4
5V
9 Mating Connector
: 1-1123722-4 (Housing)
: AMP
4
3
2
1
¨ Pin Assignment
Product Specification of Power Supply Unit
8. Input/Output pin assignment & specification
10 9 8 7 6 5 4 3 2 1
CN808
1
2
3
4
5
6
7
8
CN804
1
2
3
4
5
6
7
8
9
CN803
1
2
3
4
5
6
7
8
9
10
11
12
CN805
#1 ~ #3 : 5Vsc
#4 ~ #6 : GND
#7, #8 : 12Vsc
#9, #10 : GND
#11, #12 : NC
CN809
1
2
CN802
1
2
3
4
CN801
1
2
3
4
5
6
7
#1 : 9Vsc
#2: GND
#1 ~#2
: 30V or 24V
#3 ~ #4
: GND
Selection S/W
24V 30V
#1 : ACD
#2 : RLY ON
#3 : 5Vst_by
#4 : GND
#5 : Vs ON
#6 : 5VD
#7 : NC
8 7 6 5 4 3 2 1
#1 : Va
#2 : Va
#3 : GND
#4 : GND
#5 : GND
#6 : GND
#7 : NC
#8 : Vs
#9 : Vs
#10 : Vs
#1 ~#2
: 5Vctrl
#3 ~ #4
: GND
#1 : 9Vsc
#2 : 9Vsc
#3 : GND
#4 : 5Vsc
#5 : 5Vsc
#6 : 5Vsc
#7 : GND
#8 : GND
#9 : GND
CN807
CN806
4 3 2 1
#1 ~ #4
: +5Vctrl
#5 ~ #8
: GND
#1 : Vs
#2 : Vs
#3 : NC
#4 : GND
#5 : GND
#6 : Va
#7 : GND
#8 : +5V
Location No.
Specification
Vendor
CN01
3-176976-2(Red)
AMP
CN02
3-176976-1(Natural)
AMP
CN03
3-176976-1(Natural)
AMP
CN801
171825-7
AMP
CN802
171825-4
AMP
CN803
1-171825-2
AMP
CN804
171825-9
AMP
CN805
1-1123723-4
AMP
CN806
1-1123723-0
AMP
CN807
1-1123723-8
AMP
CN808
171825-8
AMP
CN809
171825-2
AMP
* PSU operation method S/W
1
2
Auto : Automatic On/Off
without Vsc B/D
Normal : On/Off with Vsc B/D
CN01
1
CN02
2
1
2
Neutral
Live
2
Live
1
From inlet
CN03
Neutral
Before connecting with S/W
After connecting with S/W
¨ Adjustment detail
Product Specification of Power Supply Unit
9. Adjustment detail
10 9 8 7 6 5 4 3 2 1
CN808
CN805
1
2
3
4
5
6
7
8
8 7 6 5 4 3 2 1
Vs adj.
CN804
1
2
3
4
5
6
7
8
9
CN807
CN806
4 3 2 1
* Vs Voltage Variabe Resistor
- Turn right, increase Voltage
Turn left, decrease Voltage
Selection S/W
Va adj.
CN803
24V 30V
1
2
3
4
5
6
7
8
9
10
11
12
* Va Voltage Variabe Resistor
- Turn right, increase Voltage
Turn left, decrease Voltage
* You can select output Audio Voltage(24V or 30V)
CN809
1
2
Selection S/W
CN802
1
2
3
4
Normal
(Mode1)
Auto
(Mode2)
* PSU driving method S/W
Auto(Mode2) : Driving without
1
2
interface B/D
CN801
1
2
3
4
5
6
7
Normal(Mode1) : Driving with interface B/D
* Connect with Noisefilter Cable
* Connect with S/W Cable
CN02
2
Neutral
Live
2
Live
1
2
CN03
1
1
* Connect with S/W Cable
Neutral
CN01
※ The color of CN01 is red.(The color of CN02, CN03 are natural.)
8. LABEL
LABEL Sticking Position
Coner Plate
E/X Tube
ⓐ
ⓑ
ⓒ
ⓓ
ⓔ
ⓕ
ⓖ
3211QKE008A
Z - SUS
Y-SUS
CONTROLLER
Signal Input
(R,G,B,H/Vsync.)
X left
X right
Identification Label : LABEL ⓐ
7.0 ㎝
①
②
2.5 ㎝
③
⑦
④
⑤
⑥
① Model Name
② Bar Code (Code 128, Contains the manufacture No.)
③ Manufacture No.
④ The trade name of LG Electronics
⑤ Manufactured date (Year & Month)
⑥ Manufactured place
P/N
(carved)
Trouble Shooting Manual of PDP Module
-
Introduction
Precautions
Basic
Trouble shooting
1. Introduction
COMPOSITION OF PDP BOARDS
PSU
42” V6 MODEL.
Y-DRIVE
Z-SUS B/D
TOP
Y-SUS
B/D
IPM
IPM
Y-DRIVE
BOTTOM
X-LEFT B/D
COF
COF
CONTROL B/D
X-RIGHT B/D
1. Introduction
Definitions
■ Definition of MODULE position
long 1
* Back side of module
Exhaust
hole
short 1
long 2
COF long2-1
••••••••
short 2
COF long 2-7
■ Identification label
①
②
③
6####
402K242V6000266.ASLGA ⑦
2004.02
④
⑤
⑥
① Model Name
② Bar Code (Code 128, Contains the manufacture No.)
③ Manufacture No.
④ The trade name of LG Electronics
⑤ Manufactured date (Year & Month)
⑥ The place Origin
⑦ Model Suffix
1. Introduction
■ Voltage label (Attached on back side of module)
Vsetup
-Vy
Vsc
BOARD ASS`Y
PART NO.
■ Part No. label (Attached on board)
BOARD NAME
BOARD SERIAL NO.
PCB PART NO.
■ COF serial No. label (attached on COF)
COF SERIAL NO.
1. Introduction
■ Terms of defect
Term
Appearance
Add short (line on)
Add open (line off)
Sus short (line on)
Sus open (line off)
8 /40
2. Precaution
Safety precautions
Be sure to read this before service. When using/ handling this PDP module, Please pay attention to the
below warning and cautions.
1. Before repairing there must be a preparation for 10 min.
2. Do not impress a voltage that higher than represented on the product.
3. Since PDP module uses high voltages, Be careful a electric shock
and after removing power some current remains in drive circuit.
so you can touch circuit after 1 min.
4. Drive circuits must be protected from static electricity.
5. The PDP module must be Moved by two man.
6. Be careful with short circuit of PDP boards when measuring any voltages.
Before request service
1. Check panel surface and appearance of B/D.
2. Check the model label. Whether it is boards of same model with label.
3. Before requesting Service, please inform us a detail defect phenomenon and history of module.
it can be helpful to us for a smooth sevice.
Ex) COF long 2-1 fail ,address 1 line open, Y b/d problem , mis-discharge.
9 /40
2. Precaution
Handle with care (COF)
COF is the most important component in the PDP module.
Even a little imperfection of COF can make a serious screen problem.
SCRATCHING
BENDING
TEARING
CHOPING
BEING PUSHED
3. Basic
1. X B/D
: receiving LOGIC signal from CONTROL B/D and make ADDRESS
PULSE(generates Address discharge)by ON/OFF operation,
and supplies this waveform to COF(data)
Signal part
Power part
X RIGHT B/D
X LEFT B/D
<COF Separating>
Lift up lock as shown
in narrow.
Pull COF
as shown in narrow.
3. Basic
2. Z sustain B/D
: make SUSTAIN PULSE and ERASE PULSE that generates
SUSTAIN discharge in panel by receiving LOGIC signal from
CONTROL B/D.
this waveform is supplied to panel through FPC(Z).
*composed with IPM,FET,DIODE, electrolytic capacitor ,E/R coil.
* IPM (Intelligent Power Module)
<FPC Separating>
Separate the fixed Screw of Z-Board.
Pull out Lock as shown in arrow.
E/R(Energy recovery)
Condition in Lock part is pulled
12 /40
Pull FPC Connector
as shown in arrow.
3. Basic
3. Y drive B/D
1) This is a path to supply SUSTAIN ,RESET waveform which made
from Y SUSTAIN B/D to panel through SCAN DRIVER IC.
2) Supply a wave form that select Horizontal electrode (Y SUSTAIN electrode)
sequentially.
- potential difference is 0V between GND and Vpp of DRIVER IC
in SUSTAIN period.
- being generated potential difference between GND and Vpp only
in SCAN period.
* In case of 42” V6 use DRIVER IC IC 8 EA (TOP, BOTTOM: each 4EA)
13 /40
3. Basic
4. Y sustain B/D
: generates SUSTAIN,RESET waveform, Vsc(SCAN)voltage.
and supplies it Y DRIVER B/D.
* Composed with IPM,DIODE, electrolytic capacitor ,FET.
5. Control Board
: creates signal processing (Contour noise,reduction ISM,..)
and an order of many FET on/off of each DRIVER B/D with
R,G,B each 8bit input.
* Use 3.3V/5V 2 kinds of power .
14 /40
3. Basic
DC/DC con.
part
6. DC/DC Converter part
: Being impressed 5V, Va ,Vs,
DC/DC converter makes
5V,Va,Vs,Vset_up,Vsc
which is essential for each B/D.
There is no DC/DC B/D in
model 40 〞 /42 〞(1 POWER B/D).
* 50 〞 60 〞embedded DC/DC B/D
separately because of high power
consumption.
15 /40
3. Basic
7. FPC (Flexible Printed Circuit)
: supply a driving waveform to PANEL by connecting a PAD
electrode of PANEL with PCB(Y and Z).
* there is two type of this for Y B/D. One is single-sided,
another is double-side. These are having pattern on it
* for Z B/D, there is no pattern , single-sided, and Beta
type(all of copper surface).
8. FFC (Flat Flexible Cable)
: for connecting a Logic signal between B/D and B/D.
*There is 0.5mm pitch,50pin type
1mm pitch ,30pin type.
16 /40
3. Basic
9. COF (Chip On Film)
: supply a waveform which made from X B/D to panel and select
a output pin that is controlled by COF when be on or off.
96 output pin per IC.
─ the more the resolution higher, the less spare space where
can set IC on it in B/D. without using IC PACKAGE,
we can use a BARE IC , so we can get IC with LOW COST
─ because we do not solder IC on PCB directly,
a soldering defect rate decrease.
* composition
Bare IC
1) FPC + Heat /Sink
⇒ FPC for COF must have a Low Spec decline with getting damp
2) CHIP resistor + CHIP CAPACITOR
3) BARE IC (STV7610A/WAF) + GOLD WIRE/AL WIRE
4) EPOXY MOLDING
* 42 V6 COF is the same as 42V5.
3. Basic
10. IPM(Intelligent Power Module)
: composition
HEATSINK,CAPACITOR
DIODE
IC LINEAR
RESISTORTANSISTOR,FETS.
: description
Attached at Z B/D and Y B/D, make Sustain waveform.
Sustainer : supply a square wave to panel to make a video.
IPM
18 /40
4. Trouble shooting.
Fast check
updefect?
what
kind of
defect
Check model No. of module ,all connectors and cables.
No display?
Check panel appearance
Check Y, Z b/dinput voltage
Replace Y, Z b/d
Replace ctrl b/d
vertical defect?
Check panel appearance
Horizontal defect?
Check FPC
Mis –discharge
on screen?
Check PSU output (Va,Vs,5v)
Check COF
Replace Y drv b/d
Replace Y drv b/d
Replace Y sus b/d
Replace Y sus b/d
19 /40
Replace X b/d
Replace ctrl b/d
Replace ctrl b/d
Replace ctrl b/d
Logical
judgment
what
kind
of defect?
What kind of defect ?
No display?
vertical defect?
Please follow the no display trouble shooting.
Bar defect appeared?
Please follow bar defect trouble shooting.
Line defect
Horizontal defect?
Please follow the line defect trouble shooting.
Mis –discharge
on screen?
Please follow the mis discharge trouble shooting.
20 /40
No display
Check each section with following method if there is problem, replace or repair that part.
If not go to the next section.
1. Connector
Confirm every Connector (PSU, Y-SUS, CTRL, Z-SUS)
⇒ module may not be normal by mis-connection which can not send signal and power.
Also Mis connection for a long time has a specific b/d failed.
CTRL B/D + Y-SUS
CTRL B/D + Z-SUS
CTRL B/D + X-B/D
21 /40
Signal input(LVDS)
2. Exhaust tip Crack
Confirm exhausting Tip and find Crack with naked eyes to check vacuum state.
If there is problem replace the module .
⇒ in case of vacuum breakdown, module makes a shaking noise because of inside gas ventilation.
(there may be a small crack which could not see with naked eyes. And this noise is different from Capacitor noise. )
NORMAL
CRACKED
22 /40
3. PSU(Power Supply Unit)
1. Check each unit part of PSU inside with naked eyes.
(capacitor, FET, a kind of IC, resistor)
2. Check FUSE and SW1 (on Normal).
3. Check Output voltage which is converted from AC V
SW1 Normal
to DC V.
voltage Check (5V, Va, Vs)
※ When PSU Protection occurred. Check Short
between Y-SUS, Z-SUS B/D .
Confirm
input voltage
Fuse open check
Adjust
if not same
Multi-meter Touch point
(5V, Va ,Vs must accord with Module Label)
voltages
Vs Voltage ADJ
(Vs : About 180 ~195 V)
Va, 5V(VCC) Voltage ADJ
■ Va : About 55 ~65 V
■ 5V(VCC) : 5V~5.5V)
Diode
4. Ctrl B/D
1. Confirm LED D17(flashing) ,13 lighting
2. If not CHECK OSC X1 output.
Input voltage
3. Check CTRL input voltage
(CONNECTOR P300)
4. CHECK 3.3V, 5V,15V.
5. Check IC 11 3.3V
IC 3 2.5V
OSC(X1)
Probe
Touching
point
Check IC 11,13
DMM +
Check oscillating state.
(normal 100 MHZ)
Be careful with physical shock.
DMM – (GND)
5. Y-sus B/D
1. Check FUSE [FS1(5v) ,FS2(Vs)].
Vscw
FS2
2. Check voltages(Vsetup,-Vy, Vscw)
Vsetup
3. Check DIODE between GND and Y SUS output.
setdn
[SUSUP(OC2) SUSDN(OC1)].
forward=0.4 ,reverse=OVERLOAD.
4. Check whether output voltages agrees
setup
with voltage that represented in label.
-Vy
FS1
25 /40
■ Check whether output voltages agrees with voltage that represented in label.
■ Check diode value GND between Y-SUS output.
Normal diode value= 0.4 (forward)
Normal diode value = OL (reverse)
6. Z-sus B/D
1. Check the FUSE.
2. Check input voltages.(Va, 5V,15V)
3. Check FPC out put diode value.
4. Check ramp waveform.
■ Check input voltages
■ Check the FUSE
5V FUSE
Va FUSE 6.3A
Vs FUSE 2A or 4A
■ Variable resistance of Z RAMP
waveform slope.
■ Check FPC output diode value.
caution: check certainly after removing FPC.
Normal diode value=0.375(forward)
Normal diode value=OVER LOAD(reverse)
◎
Power protection
It is power protection when power is off automatically within 2~3 min. from power on.
Power protection function protect the boards when occurred short on circuits of PDP module or power problem.
If can not impress power even after replacing PSU, find out where the short occurred.
* PSU makers.
DAEGIL PSU
UNICON PSU
29 /40
Vertical defect (bar)
Check each section with following method if there is problem, replace or repair that part.
If not go to the next section.
1. Connector
Check here
Bar
Check COF connector.
If not connected well,it will Make a bar defect .
Check here
Off
2. Checking COF
Confirm whether COF was torn. And then check input of COF resistor and IC.
COF 6 is torn partly
Tearing
30 /40
◎
Checking address COF input of resistor and IC
■ COF resistor checking
Check the both side of resistor With Digital multi meter(DMM) .
If the resistor is normal, the resistor value will be 10.2 ~ 10.8 Ω
But if not, the value will be 0 or infinity and replace the resistor.
31 /40
◎
Checking address COF input of resistor and IC
■ IC input checking
Inside of IC , there is 4 ea diodes which separated in 2 series .
(input 2, output 2)
*how to check
1.contact DMM - terminal to a right terminal of condenser(GND)
and DMM + terminal to a right terminal of IC, normal value 0.66 (fig.1)
2.contact DMM - terminal to Output terminal of resistor, and
DMM + terminal to a right terminal of IC , normal value 0.73 (fig.2)
Fig. 2
Fig. 1
DMM(- terminal)
`
DMM (+ terminal)
DMM (- terminal)
DMM( + terminal)
3. Ctrl B/D
CTRL B/D supplies video signal to COF. So if there is a bar defect on screen,
It may be the ctrl b/d problem.
<Diagram of ctrl b/d>
A flow of address signal
In this figure, we can easily suppose
MCM
what will be appeared on screen when a specific part failed.
Buffer
IC
Array저항
각각 16 line
COF IC1
96 output
COF IC2
COF IC3
COF IC4
Vertical defect (line)
In case of 1 line open or short , check foreign substances in COF connector.
First blow up foreign substances with your mouth. And then if the same line appears, replace the panel.
1 line open or short
This phenomenon is due to COF IC inside short or adherence part of the Film and rear panel electrode problem.
In this case, replace the panel.
1 electrode open
1 line open
Line open or short with same distance.
This is MCM of Ctrl b/d defect. MCM can not be replaced separately. So replace the ctrl b/d.
MCM (Multi Chip Module)
line defect from each parts
• Case 1: Buffer IC fail
16 line open
COF IC 1,2 ⇒ 192 line(96+96) open.
COF IC 3,4 ⇒ 64 line open (with fixed interval there is on,off ……. Repetition)
• case 2 : Array resistor fail
COF IC1 ⇒ 16 line , COF IC2 ⇒ 16 line open
• case3 : COF IC fail
96 line open
96 line open.
/40
Horizontal (bar)
Most horizontal defects can be repaired. In case of adherence part of the Film and rear panel
electrode defect or panel electrode open,short , replace the panel.
1. Connector
It can make a horizontal bar that connector on Y b/d and Z b/d did not plugged well. Because sustain voltage
can not be supplied to panel. So check connectors (FPC, Y drv –Y drv) first.
Disconnected
Disconnected
Horizontal bar
Screen off
2. Scan IC check
Check diode value of the right side part of output pin.
Normal diode value. (in case of Panasonic IC=1.035)
Defect diode value= 0.018
* It can be different from each IC Maker. (in case of TI IC= 0.6~0.7)
DMM +
DMM -
Check here with DMM(either forward or reverse is ok)
37 /40
Horizontal (line)
1. Check FPC
In case of horizontal 1 or more line, it is due to FPC or panel inside .
ctrl b/d, Y b/d is just normal.
FPC electrode open
Panel electrode
Insulation break down
Horizontal 1 line.
2. Check scan IC
Check with same method that presented in Horizontal (bar).
38 /40
◎
How to check IPM
Forward : test 1 GND(＋) , Sus-out(－)
2 Sus-out(＋),Vs(－)
3 ER-DN(－),ER-COM(＋)
4 ER-COM(－),ER-UP(＋)
when each 4 TEST Diode value is over 0.4V => OK
Reverse : test 1 GND(－) , Sus-out(＋)
2 Sus-out(－),Vs(＋)
3 ER-DN(＋),ER-COM(－)
4 ER-COM(＋),ER-UP(－)
when each 4 nodes TEST Diode value is infinity => OK
※ Specially, the value of ER-UP,COM,DN in the Y/Z board, should be
checked all of them. but, the terminal of Vs,Sus-out,GND,
we must aware to know after check one of IPM because it is parallel.
Æ
if no problems, check 15V(Y,Z B/D) with GND, Î Forward value 0.3V,
Reverse value infinite. If no problems,
40 /40
BOM Summry Report with Cost （ Report For PDP4206EM　）
Item Component
一. ElEC Parts
1 E3403-004001
2 E3421-926004
3 E3421-926006
4 E3421-926007
5 E4406-068001
6 E4406-069001
7 E4850-003001
8 E4850-004001
9 E6205-001003
10 771-42D103-01
11 771-42D102-01
12 771-42D101-01
13 774P42D101-01
14 771E42D101-01
15 771L42D101-05
二. Mech Parts
1 200-42D121-21A
2 244-34B801-01
3 248-46D201-01
4 263-42D101-01S
5 269-42D101-01L
6 326-050010-40
7 326-095010-40
8 361-101261-01
9 367-42D101-01
10 367-42D102-01
11 384-42D101-03
12 384-42D102-01
13 387-42D101-06H
14 388-42D102-01
15 388-42D103-01H
16 388-42SB02-01H
17 388-42SB04-01H
18 402-42D112-01
19 423-42D107-01
20 423-42D108-01
21 423-42D10C-01
22 423-42D10F-01
23 423-42D113-01
24 423-42D114-01
25 423-42D115-01
Description/Country Origin
Unit
Quantity
Summary
TUBE SUMITUBE
D5.0 BLK
600V
WIRE ASSY 1H2.5-2H2.5
L270 12P/2+
WIRE ASSY TJC3-4Y/AMP-4Y/210 FOR S
WIRE ASSY 1H2.5-2H2.5 L330
31P (LV
FILTER EMI CTRC-0930-1B
FOR 42
FILTER EMI CTNF-100B
FOR 4
SPEAKER SUB(FOR 42TD1)
16 OHM
SPEAKER SUB (FOR 42TD1)
16 OHM
DISPLAY PDP LG-V6 42"
WITH FI
REMOTE RECEIVE PCB ASSY
SPK JACK PCB ASSY
KEY PCB ASSY
POWER ASSY PDP42
Main PCB
AUDIO PCB ASSY (LG/V6) W/O TUNER FOR USA
M
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
Sect
Sect
0.3
1
1
1
3
1
1
1
1
1
1
1
1
1
1
FRONT CABINET BLACK ENG 42TD1 W/O TV
GIFT BOX HANDLE
34B8
HANDLE FOR PLASMA
POWER LENS
42D1
REMOTE LENS
42D1
SPONGE CUSHION 500X10X4.0MM W/ADHESI
SPONGE CUSHION 950X10X4.0MM W/ADHESI
CABLE TIE
EDGE SADDLE 14MM
42D1
EDGE SADDLE 27MM
42D1
TUNER BOARD PLATE ENG 42TD1 W/O RF
PVC SHEET FOR MAIN BOARD 42D1
MODEL PLATE AKAI ENG 42TD1(JIAYING)
PC SHEET FOR REMOTE PCB42D1 94V0 0.3
CAUTION PLATE ENG
42D1
H
SPK PLATE MAIN SANSUI 42" 42SB
POWER PLATE SANSUI
42SB
BACK COVER FOR V6
42D1
PANEL PATCH V6
42D1
PATCH FOR SHIELD BOX
42D1
SUPPORT FOR PW BKT
42D1
CONNECT SHEET
42D1
FILTER SUPPORT TOP
42D1
MAIN BKT FOR V6
42D1
POWER BKT FOR V5/V6
42D1
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
1
2
2
1
1
2
2
28
4
2
1
1
1
1
1
1
1
1
4
1
1
2
1
2
1
26 423-42D122-01
27 423-42SD21-01S
28 430-42D101-01
29 436-42D105-01
30 457-42D101-01
31 481-42D111-01
32 481-42D112-01
33 483-42D101-01
34 483-42D102-01
35 512-42D101-01
36 512-42D102-01
37 553-002007-40A
38 553-002509-25A
39 553-004009-40A
40 553-005009-25A
41 553-012509-40A
42 553-017009-25A
43 553-020009-40A
44 553-024509-40A
45 553-056009-40A
46 553-095009-40A
47 554-080030-01
48 563-11949 568-P46T02-02
50 579-42D102-09
51 579-42D102-14
52 579-42D103-02
53 579-42D105-01
54 590-42D101-06
55 600-305008-00
56 601-305008-00
57 602-305006-10
58 604-305005-30
59 604-601020-00
60 60D-407010-40
61 610-300210-00
62 612-300210-00
63 614-260208-10
64 614-400408-10
65 614-400412-00
66 615-400214-00
67 619-300210-10
68 900-42D103-01
三. Packing
1 300-42D111-02C
2 300-42D112-02C
3 310-504004-01
FILTER SUPPORT L&R
42D1
FILTER SUPPORT BOTTOM 42SD
HEATSINK FOR AUDIO IC 42D1
TERMINAL SHEET W/O RF HOLE
CLAMP ID=4.3MM L=46MM
SHIELD BOX FOR MAIN PCB JIAYING
SHIELD BOX FOR TUNER PCB JIAYING
SHIELD COVER A
42D1
SHIELD COVER B
42D1
SHEET 1160X1160
42D1
SHEET 1160X1480
42D1
SHIELD GASKET 20X7X4.0MM W/CONDUCTIV
SHIELD GASKET 125X9X4.0MM W/CONDUCTI
SHIELD GASKET 170X9X2.5
SHIELD GASKET 560X9X4.0 W/CONDUCTIVE
SHIELD GASKET 950X9X4.0 W/CONDUCTIVE
SHIELD CLOTH 80X30MM W/CONDUCTIVE AD
SERIAL NO. LABEL
WARNING LB ENG
42SF NIL
SERIAL NO/BAR CODE LABEL 42D1
BAR CODE LABEL AKAI PD4206EM(USA)
ON/OFF LB ENG
42D1 NIL
PROTECTIVE EARTH LABEL FOR ESA 42TD1
WARRANTY CARD AKAI PDP4206EM(USA)
MACH.SCREW PAN 3X8
BZN +
MACH.SCREW CTS 3X8
BZN +
MACH.SCREW WHR 3X6
NIP +
MACH.SCREW BID 3X5
BNI +
MACHINE SCREW BINDING M6X1.0PX20MM B
MACH. SCREW W/SPRING WASHER M4.0X0.7
S-TAP.SCREW RND 3X10
A BZN +
S-TAP.SCREW WHR 3X10
A BZN +
S-TAP.SCREW BID 2.6X8
A NIP +
S-TAP.SCREW BID 4X8
D NIP +
S-TAP.SCREW BID 4X12
T BZN +
SELF-TAPPING SCREW
W/BIG WASHER
SPECIAL SCREW 3X10 NP "+"
PANEL DISPLAY FILTER OPTIMAX
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
PCS
2
1
1
1
7
1
1
1
1
0.2857
0.2857
4
2
1
1
11
2
4
2
2
2
2.5
1
1
1
2
1
1
1
2
2
17
22
6
21
2
7
2
2
34
1
23
1
POLYFOAM FOR MAIN UNIT 42D1 TOP
POLYFOAM FOR MAIN UNIT 42D1 BOTTOM
POLYBAG EPF 50"X40"X0.04
PCS
PCS
PCS
1
1
1
4 510-42D104-01K
5 511-42D101-01K
四. ACCESSORY
1 511-42D102-01A
2 790-003603-A9
3 580-42D101-11
4 310-111404-07V
5 E3404-157001
6 E7301-010002
7 734-BM0305-01
GIFT BOX AKAI 1154(W)X320(D)X1032(H)
CARTON BOX FOR BTM
42D1
PCS
PCS
1
1
ACCESSORY BOX
AKAI Remote 0036 for PDP4206EM
INSTRUCTION BOOKLET E FOR AKAI PDP42
POLYBAG
11"X14"X0.04
AC CORD UL 1.88M MET-4D7+SJT 16AWG/
BATTERY AAA R03P1.5V <2>
SECC STAND BASE 42" B/G BOX W/O POLY
PCS
PCS
PCS
PCS
PCS
PCS
SET
1
1
1
1
1
2
1
Exploded View
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
ITEM
614-400412-00
615-400412-00
423-42D10C-01
423-42D108-01
367-42D102-01
604-601020-00
248-P46U02-01
622-302408-10
23845857
560-42D101-01
384-42D102-01
384-42D101-01
402-42D10X-01
483-42D102-01
602-305006-10
E7801-043004
612-300210-00
604-305005-630
436-42D101-01
481-42D102-01
SCREW 4x12
SCREW 4x14
SUPPORT FOR PW BKT
PATCH FOR SHIELD BOX
EDGE SADDLE 27MM
MACH.SCREW M6x20
HANDLE
STP SCREW 3x8
CLAMP
MODEL PLATE
PVC SHEET FOR TUNER BOARD
PVC SHEET FOR MAIN BOARD
VACK COVER
SHIELD COVER B
MACH. SCREW 3x6
TUNER BOARD
STP SCREW 3x10
MACH. SCREW 3x5
BAK TERMINAL SHEET
SHIELD BOX B
483-42D101-01
E7801-043006
367-42D101-01
481-42D101-01
614-300210-00
423-42D115-01
E4405-035001
601-306008-10
E4101-027001
771-42D102-01
423-42D114-01
423-42D107-01
60D-407010-10
E4850-002001
614-400416-00
E6205-001003
322-501004-01
322-951004-01
610-300210-10
423-42D101-01
423-42D102-01
423-42D103-01
559-500925-01
559-950925-01
900-42D101-01
614-400480-10
277-42D101-XXS
771-42D101-01
388-42D101-01
614-260208-10
388-42D102-01
771-42D103-01
269-42D101-01L
263-42D101-01S
200-42D101-XXS
PART NO.
SHIELD COVER A
MAIN BOARD
EDGE SADDLE 14MM
SHIELD BOX A
STP SCREW 3x10
POWER BKT FOR V5/V6
AC LINE FILTER
MACH. SCREW 3x8
POWER SWITCH
AV JACK PCB
MAIN BKT FOR V6/FORMOSA
PANEL PATCH FOR V6
MACH. SCREW W/SP WASHER 4x10
SPK BOX
STP SCREW 4x16
PLASMAS PANEL
CUSHION 500x10x4MM
CUSHION 950x10x4MM
STP SCREW 3x10
FILTER SUPPORT BTM
FILTER SUPPORT L&R
FILTER SUPPORT TOP
SHIELD GASKET 500x9x2.5MM
SHIELD GASKET 950x9x2.5MM
DISPLAY FILTER LG
STP SCREW 4x8
FUNCTION KNOG
KEY PCB
PC SHEET FOR KEY PCB
STP SCREW 2.6x8
PC SHEET FOR REMOTE PCB
REMOTE PCB
REMOTE LENS
POWER LEN
FRONT CABINET
DESCRIPTION
1
1
1
1
2
4
2
2
4
1
1
1
1
1
14
1
7
22
1
1
1
1
4
1
2
1
1
2
1
1
2
4
20
1
33
1
2
2
22
1
2
1
2
2
1
2
5
1
1
5
1
1
1
1
1
QTY
REMARK
If you forget your V-Chip Password
- Omnipotence V-Chip Password: 363200.
- Press MENU Right button.
- Press CH+, CH- or Up, Down buttons to highlight "CC-VChip" Control.
- Press MENU Right and Up, Down buttons to highlight "Change Blocking Password".
- Press Right button to pop up "Old Password".
- Use the Number buttons (0~9) to enter an omnipotence Password.
- Press Right button to confirm and will pop up "Password Change Successful".
- Suggest: Change to your familiar Password again.
Software upgrade
- Connect the RS-232C input jack to an external control device (such as a computer) and software upgrade.
Type of connector; D-Sub 9-pin male
No.
1
2
3
4
5
6
7
8
9
1
Pin name
No connection
RXD (Receive data)
TXD (Transmit data)
DTR (DTE side ready)
GND
DSR (DCE side ready)
RTS (Ready to send)
CTS (Clear to send)
No Connection
5
9
6
RS-232C configurations
3-wire configuration
(Not standard)
7-wire configuration
(Standard RS-232C cable)
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
PDP
2
3
5
4
6
7
8
3
2
5
6
4
8
7
D-Sub 9
D-Sub 9
TXD
RXD
GND
DSR
DTR
CTS
RTS
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
PDP
2
3
5
4
6
7
8
3
2
5
4
6
7
8
D-Sub 9
D-Sub 9
TXD
RXD
GND
DTR
DSR
RTS
CTS
Software upgrade Process
- Power Switch OFF.
- Connect the RS-232 jack of the computer to the RS-232 jack on the plasma back panel.
RS-232C connection cables are not supplied with the Plasma.
Computer
RS-232
PDP
RS-232
- Power Switch ON. The power indicator on the front of the panel should now display red, that the
Plasma is in standby mode.
- Copy the software (Flash Upgrader) to the computer.
- Open the software (Flash Upgrader.exe)
- Point "Flash" on the interface of the Flash Upgrader.exe.
Flash
- Press STANDBY button on the front panel or POWER button of Remote control, Power indicator is
green, the Plasma is in power ON mode, software start upgrader immediately.
- Hard Reset after the upgrader is finished.
Method: 1. Power Switch Off
2. Power Switch On again
3. Sequence press F.WHITE, VIDEO, I.P.C. button on the Remote control enter factory Menu
select "Misc.", "Hard Reset", press Menu Right button to Hard Reset is finished.
4. If the color of picture is abnormal, Hard Reset again.
Misc.
Hard Reset
- After the Hard Reset is finished, shut down the power switch, take out the RS-232C connection cables
after the power indicator is extinguished.
Note: The computer and plasma must be keep Power ON in the software upgrade processing.
If the function is abnormal, software upgrade again.

AKAI PDP4206EM Service Manual

Transcription

Similar documents

Chassis L5A-26"…32"

l6b tft- lcd tv service manual

DVD Home Theater Sound System

LASER PRINTER ML