Supra eKEY® for Android™ Products User Manual

Supra eKEY® for
Android™ Products
User Manual
ii
Copyright
Disclaimer
© 2013 United Technologies Corporation. All rights reserved.
November 2013
The information in this document is subject to change without notice. United Technologies
Corporation (“UTC”) assumes no responsibility for inaccuracies or omissions and specifically
disclaims any liabilities, losses, or risks, personal or otherwise, incurred as a consequence,
directly or indirectly, of the use or application of any of the contents of this document. For the latest
documentation, contact Supra or visit us online at www.supraekey.com.
This publication may contain examples of screen captures and reports used in daily operations.
Examples may include fictitious names of individuals and companies. Any similarity to names and
address of actual businesses or persons is entirely coincidental.
Trademarks and
patents
Supra and eKEY are registered trademarks of United Technologies Corporation. Android and
Google Maps are trademarks of Google, Inc. Bluetooth is a registered trademark of Bluetooth SIG.
Other trade names used in this document may be trademarks or registered trademarks of the
manufacturers or vendors of the respective products.
Intended use
Rules and
regulations relating
to the use of the
service
Use this product only for the purpose it was designed for. For the latest product information,
contact Supra or visit us online at www.supraekey.com.
Key Possession. Each keyholder (“Keyholder”) is responsible for the key (“Key”) issued to him or
her.
Current Update. The Key must be updated in order to access keyboxes (“Keyboxes”). The Key
cannot be updated unless the Keyholder is in good standing with the organization (“Organization”)
and United Technologies Corporation (“UTC”), is authorized to use the Service, and is in
compliance with the obligations for the use of the Service including, without limitation, these rules
and regulations.
Equipment Security. It is necessary to maintain the security and the personal identification number
(“PIN”) of the Key to prevent the use of the Key and the Service by unauthorized persons. Each
person in possession of a Key, whether such Key is being actively used or not, shall abide by the
following terms and conditions:
To keep the Key in authorized Keyholder’s possession or in a safe place at all times;
Not to allow the PIN for the Key to be displayed on or attached to the Key for any purpose
whatsoever or to be disclosed to any third party;
Not to lend or otherwise transfer the Key to any other person or entity, or permit any other person
or entity to use the Key for any purpose whatsoever, whether or not such other person or entity is
authorized to use the Key;
Not to duplicate the Key or allow any other person to do so;
Not to assign, transfer or pledge the Key;
Not to (i) destroy, alter, reproduce, modify, adapt, translate, reverse engineer, de-compile,
disassemble or tamper with the Key or knowingly or unknowingly allow anyone else to do so; or (ii)
provide or otherwise make available the software or any part or copies thereof to any third party;
To notify your Organization or UTC within forty-eight (48) hours if the Key is lost or stolen;
To follow all additional security procedures as specified by your Organization; and
To safeguard the code for each Keybox from all other individuals and entities, whether or not they
are authorized users of the service.
Keybox Authorization. Before a Keybox is installed or used on any piece of real property, the prior
written authorization to install or use a Keybox must be obtained from the property owner, as well
as from any tenant(s) in possession of the property, if applicable. Extreme care shall be used to
ensure that all doors to the listed property and the Keybox are locked. All owners and/or tenant(s)
of real property shall be informed that the Keybox is not designed to be, or intended as, a security
device.
iii
Table of Contents
Preface................................................................................................................................. v
Safety Terms and Symbols............................................................................................ v
Chapter 1
Introduction.....................................................................................1
eKEY Overview.................................................................................................................... 2
Requirements................................................................................................................ 2
Supra eKEY Application Software................................................................................. 2
Supra eKEY Fob............................................................................................................ 3
SupraWEB..................................................................................................................... 3
KIMvoice........................................................................................................................ 4
eKEY Setup.......................................................................................................................... 4
Install eKEY Software.................................................................................................... 4
Authorize eKEY............................................................................................................. 5
Customize PIN............................................................................................................... 6
Audio and Vibrate Settings............................................................................................ 6
Chapter 2
Updating...........................................................................................8
Update Overview................................................................................................................. 9
Manual Update.............................................................................................................. 9
Automatic Update........................................................................................................ 11
Chapter 3
Access iBox...................................................................................12
iBox.................................................................................................................................... 13
Supra eKEY Fob.......................................................................................................... 13
Release the Key Container.......................................................................................... 15
Place Listing Keys in the iBox..................................................................................... 16
Feedback..................................................................................................................... 16
Showing Hours............................................................................................................ 17
Call Before Showing (CBS)......................................................................................... 17
Cooperating................................................................................................................. 18
Release the Shackle ................................................................................................... 19
iBox Inventory................................................................................................................... 20
View iBox Inventory and Detail Information................................................................. 20
Add an iBox to Inventory............................................................................................. 21
Delete an iBox from Inventory..................................................................................... 22
Read Activity................................................................................................................ 22
View Showing Activity.................................................................................................. 23
Delete Showing Activity............................................................................................... 24
Change iBox Settings.................................................................................................. 24
Chapter 4
MLS Listings and Roster..............................................................26
eKEY Professional............................................................................................................ 27
Settings for eKEY Professional.................................................................................... 27
Listings.............................................................................................................................. 28
Market Area................................................................................................................. 28
Update Listings............................................................................................................ 30
View Listings................................................................................................................ 30
Delete Listings............................................................................................................. 35
iv
Roster................................................................................................................................. 36
View Roster................................................................................................................. 36
Delete Roster............................................................................................................... 37
Chapter 5
Showing Activity...........................................................................38
Showing Activity............................................................................................................... 39
Voice Report................................................................................................................ 39
Showing Notifications and Messages.......................................................................... 39
Showings Activity on Android Devices......................................................................... 41
Disable eKEY Showing Notifications........................................................................... 42
Update Listing ID......................................................................................................... 42
Chapter 6
Support and Troubleshooting......................................................43
Support.............................................................................................................................. 44
Training Library............................................................................................................ 44
Help Screens............................................................................................................... 45
v
Preface
The Supra eKEY for AndroidTM Products User Manual includes an overview of the Supra eKEY
application software and detailed instructions explaining:
•
how to set up the eKEY application software
•
how to update the eKEY app to access an iBox
•
how to access an iBox
•
how to view MLS listing and roster data
•
how to view showing activity
There is information describing how to contact technical support.
For specific information about an Android device, refer to the documentation that was provided with the smartphone or tablet. For additional information on using the Supra eKEY software, visit www.supraekey.com and select the Customer Support link.
The following conventions are used in this document:
Bold
Menu items and buttons.
Italic
Emphasis of an instruction or point; special terms.
File names, path names, windows, panes, tabs, fields, variables, and other GUI elements.
Titles of books and various documents.
Blue italic
(Electronic version.) Hyperlinks to cross-references, related topics, and URL addresses.
Monospace
Text that displays on the computer screen.
Programming or coding sequences
Safety Terms and Symbols
These terms may appear in this manual:
CAUTION: Cautions identify conditions or practices that may result in damage to the equipment or other
property.
Chapter 1
Introduction
Chapter 1 Introduction
This chapter provides an overview of the eKEY application software and
explains how to set it up on the AndroidTM device.
In this chapter:
eKEY Overview......................................................................................... 2
Requirements....................................................................................... 2
Supra eKEY Application Software........................................................ 2
Supra eKEY Fob................................................................................... 3
SupraWEB............................................................................................ 3
KIMvoice............................................................................................... 4
eKEY Setup............................................................................................... 4
Install eKEY Software........................................................................... 4
Authorize eKEY.................................................................................... 5
Customize PIN..................................................................................... 6
Audio and Vibrate Settings................................................................... 6
1
Chapter 1
Introduction
eKEY Overview
The eKEY application software allows the AndroidTM phone or tablet to access a Supra iBox placed at
real estate listings. There are three (3) different versions of the iBox that may be placed on listings depending upon the Multiple Listing Service (MLS), Association, or Board.
The classic iBox (the original Supra iBox) reads an infrared signal only. To access an iBox using infrared, the Supra eKEY Fob is required. The iBox BT and iBox BT LE read infrared and Bluetooth®
signals. In addition, the iBox BT LE uses a low energy battery. The eKEY Fob is not required to
access the iBox BT or iBox BT LE.
Requirements
•
eKEY compatible Android smartphone or tablet; to see which Android devices are supported go
to www.supraekey.com or click here.
•
Android Operating System (OS) 2.1 or newer
•
Android data plan with Internet service
•
Supra eKEY Fob to access iBox devices using infrared
Supra eKEY Application Software
The eKEY application allows the user to:
•
Obtain the listing keys from an iBox
•
Open the shackle on an iBox to place it on a listing or remove from a listing
•
Manage and view the iBox inventory and change iBox settings
•
Read an iBox to view showing history
•
View showing notices and messages
•
View MLS and roster information — only for eKEY Professional subscribers
Figure 1. eKEY Basic Home Screen
2
Chapter 1
Introduction
Figure 2. eKEY Professional Home Screen
The eKEY software connects regularly to the Supra network using the Android device’s cellular Internet
service or Wi-Fi connection. During the first eSYNC of each day, the eKEY software sends showing
data to the Supra network, updates the eKEY to access the iBox, and receives messages and showing
notifications. In addition, for eKEY Professional subscribers, the MLS listing and roster data are
updated.
Supra eKEY Fob
The Supra eKEY Fob is a device used to translate the Bluetooth signal from the Android device to an
infrared signal that can be recognized by the iBox. For more fob pairing information, view the eKEY Fob Instructions packaged with the fob, or follow the manufacturer’s pairing instructions for the
Android device.
SupraWEB
SupraWEB is the agent website, available at www.supraekey.com; to go and:
•
Obtain an update code for the eKEY
•
Identify the name of a keyholder by key serial number
•
Manage the iBox inventory and listing information
•
View, email, and schedule activity reports
•
View and send showing feedback
•
Manage billing
•
Change the PIN code
•
Set up the market area (eKEY Professional subscribers only)
•
Obtain an authorization code to install the eKEY software
To access SupraWEB from the Andriod device, open the eKEY application and select the SupraWEB
icon.
3
Chapter 1
Introduction
KIMvoice
The Keybox Information Manager (KIM), is the Supra network that maintains the key and iBox data. Call KIMvoice at 888‑968-4032 to use the automated voice access system.
eKEY Setup
This section explains how to install and authorize the eKEY application software.
Install eKEY Software
Use the Android Market, Google Play, or Play Store to install the eKEY software. A data package with
Internet service is required to use the Supra eKEY software.
Install the eKEY software on the Android device:
1. On the Android device, select the Market, Google Play, or Play Store icon.
2. Select Search and search for eKEY.
3. Select the Supra eKEY application.
4. Select INSTALL.
5. Select OK.
After the software is installed, the eKEY icon is shown in the list of applications on the Android device.
Figure 3. eKEY Icon
4
Chapter 1
Introduction
Authorize eKEY
The eKEY software must be authorized before it can be used. To authorize the eKEY software, a
30-digit Authorization code is required.
New eKEY users can obtain an authorization code from the Association/Board/MLS. For existing eKEY
users, log into SupraWEB and select the Authorization Code link to obtain an authorization code.
Demo mode is available for customers who have not yet subscribed to the eKEY service. Use the
Demo mode to view the eKEY software only, no interaction with the iBox is possible in this mode.
Authorize the eKEY software:
1. Select the eKEY icon to open the application.
2. Select Activate eKEY.
3. Follow the onscreen prompts to enter the 30-digit Authorization code.
4. Select Authorize.
The eKEY app will use the Android device to connect, authorize, and update the eKEY app to access
iBox devices.
Figure 4. Authorize eKEY Screen
5
Chapter 1
Introduction
Customize PIN
Customize the PIN code to use with the eKEY software.
Customize the PIN:
1. Using a computer, navigate to www.supraekey.com.
2. Select SupraWEB Login for Real Estate Agents.
3. Enter your user ID and password and select Login.
Note: To register for a single sign on (SSO) user ID and password, click the Register button to register for a login.
4. Select Change PIN.
Figure 5. Change PIN Code Screen
5. Enter the current PIN code.
6. Enter the new PIN code and re-enter to confirm.
7. Select Save.
8. Verify cell/data coverage.
9. On the Android device, select the eKEY icon to open the eKEY application.
Audio and Vibrate Settings
The eKEY software uses several audio tones along with messages on the screen to communicate the
status of iBox operations and alerts the Android device when a new showing or message is received. If an error occurs, the Android device will vibrate and sound a buzz tone.
The audio and vibrate feedback in the eKEY software can be disabled. Disabling the audio or vibrate
feedback in the eKEY software does not affect other Android applications.
6
Chapter 1
Introduction
Disable the audio or vibrate in the eKEY software:
1. On the Android device, select the eKEY icon to open the eKEY application.
2. Select Settings.
Note: For eKEY Professional, the Settings icon is on the second page of icons.
3. Uncheck or check the Audio Feedback or Vibrate Feedback option to toggle on and off.
4. Select the Save button to save the changes.
Figure 6. Disable Audio or Vibrate Feedback Toggle
7
Chapter 2
Updating
Chapter 2 Updating
This chapter explains how to update the eKEY software.
In this chapter:
Update Overview.......................................................................................9
Manual Update..................................................................................... 9
Automatic Update................................................................................11
8
Chapter 2
Updating
Update Overview
The eKEY software permission expires each night at midnight. It connects to the Supra network using
the Android device’s cellular service. The eKEY software will automatically update if the Automatic
Update setting is checked, otherwise it will update once daily when the eKEY application is opened.
The eKEY software will not update if the Automatic Update in the eKEY software is turned off, the
Android device is turned off, or out of cell/data coverage.
In order for an update to occur:
• Android device is powered on
• cell/data coverage
• good standing with the Association or Organization
• good standing with Supra
To see if the eKEY software is expired, open the eKEY application. The Update icon shows a red X
through the icon when it is expired.
Figure 7. Key Expired Icon for eKEY Basic and eKEY Professional Main Menu
Manual Update
If the eKEY software is expired and the Android device has cell/data coverage, perform a wireless
manual update.
1. Verify cell/data coverage.
2. Open the eKEY application.
If the eKEY software is expired and the Android device is out of cell/data coverage, manually update by
obtaining and entering an update code.
9
Chapter 2
Updating
Obtain an update code from SupraWEB:
1. Go to www.supraekey.com and select SupraWEB Login for Real Estate Agents.
2. Enter your user ID and password and select Login.
Note: For setup purposes only, the first login requires the key serial number, user ID, and association
or MLS name.
3. Select the Update Code link under Quick Links and the update code displays.
Obtain an update code from KIMvoice:
1. Call KIM at 1-888-968-4032.
2. Enter your eKEY serial number and PIN code into the Android device, followed by the # sign.
3. Press 1 on the phone for an update code.
Enter the update code into the eKEY software:
1. Open the eKEY application.
2. Select the Android Menu button.
3. Select Emergency Update.
4. Enter the update code.
5. Select Update Key.
Figure 8. Enter Update Code
The number of consecutive update codes is limited. Once the update code limit is reached, perform a
wireless update before any additional update codes are requested.
10
Chapter 2
Updating
Automatic Update
Uncheck the Automatic Key Update box to turn off the automatic update. If the automatic key update is
disabled, update the eKEY software before going out to a listing.
Disable the automatic key update:
1. Open the eKEY application.
2. Select Settings.
Note: The eKEY Professional Settings icon is on the second page of icons.
3. Uncheck Automatic Key Update.
4. Select the Android Back button to return to the eKEY main screen.
Figure 9. Disabling Automatic Updates
In addition to the automatic update the first time the eKEY software is opened each day, the eKEY
software automatically updates and sends detailed information immediately after each key container
opening and shackle release.
11
Chapter 3
Access iBox
Chapter 3 Access iBox
This chapter explains how to access and manage iBox devices and gives
information on Call Before Showing (CBS) and accessing cooperating iBox
systems.
In this chapter:
iBox.......................................................................................................... 13
Supra eKEY Fob................................................................................. 13
Release the Key Container................................................................ 15
Place Listing Keys in the iBox............................................................ 16
Feedback............................................................................................ 16
Showing Hours................................................................................... 17
Call Before Showing (CBS)................................................................ 17
Cooperating........................................................................................ 18
Release the Shackle ......................................................................... 19
iBox Inventory........................................................................................ 20
View iBox Inventory and Detail Information........................................ 20
Add an iBox to Inventory.................................................................... 21
Delete an iBox from Inventory............................................................ 22
Read Activity....................................................................................... 22
View Showing Activity......................................................................... 23
Delete Showing Activity...................................................................... 24
Change iBox Settings......................................................................... 24
12
Chapter 3
Access iBox
iBox
The eKEY application software allows access to the classic iBox, iBox BT, and iBox BT LE to:
•
release the key container
•
release the shackle
•
change the iBox settings
•
read the showing history stored in an iBox
Figure 10. Supra iBox Devices
Shackle
Shackle
Bluetooth signal
Infrared lens
iBox BT LE
iBox BT
Classic iBox
The iBox BT LE and iBox BT communicate with Android devices using Bluetooth technology. Press up
on the bottom of the iBox BT LE to turn on Bluetooth and begin an operation.
The classic iBox communicates using infrared technology. The Supra eKEY Fob is required to access
the classic iBox with all Android devices. The fob translates the Bluetooth signal from the Android
device into an infrared signal that can be understood by the classic iBox. The distance between the
fob and the infrared lens on the iBox should be less than a foot. Direct sunlight can interfere with the
infrared communication and shading the area between the fob and the iBox may be required.
Supra eKEY Fob
The eKEY application uses the eKEY Fob as a Bluetooth-to-infrared translator to communicate with
classic iBox devices. Some older Android devices may require pairing with the fob.
The first time the fob is used, a numeric passkey may be required depending on the Android model.
The numeric passkey is 0000 (four zeros).
Tip: On some Android device models, tap on the Bluetooth icon and drag the pairing alert down to
accept the pairing and enter the passcode.
To use the eKEY fob, start the procedure on the Android. When the software prompts, power on the
eKEY fob by pressing the power button until the green light flashes. When the green light flashes, point
the eKEY fob at the infrared lens on the iBox.
13
Chapter 3
Access iBox
Figure 11. Supra eKEY Fob
Pair the fob with Android devices:
Experiences may vary depending on the model and OS of the Android device. Read and follow the
Android manufacturer’s instructions on How to Pair Devices for specific information.
1. On the Android device, select Settings.
2. Select Bluetooth.
3. Set Bluetooth to On.
4. Search for devices.
5. Power on the eKEY Fob by pressing and holding the power button until the green light flashes.
6. When the Supra-xxxx (example: SUPRA-D817) is visible, tap to connect.
Figure 12. Pair Bluetooth for eKEY Fob
Use the fob:
Tip:
The distance should be less than a foot between the fob and the iBox to communicate. Direct
sunlight can interfere with infrared communication. If required, shade the area between the fob
and iBox when they are communicating.
1. Start an eKEY operation (Obtain Key or Open Shackle).
2. When the eKEY software prompts, press the power button until the green light flashes to power
on the eKEY Fob.
3. Point the fob at the infrared lens on the iBox.
14
Chapter 3
Access iBox
Release the Key Container
Release the key container on an iBox device:
1. Select the eKEY icon to open the eKEY application.
2. Select the Obtain Key icon.
3. Enter your PIN code.
4. If the iBox requires an additional Call Before Showing (CBS) code, check the CBS Required box
and enter the CBS code for the iBox (see “Call Before Showing (CBS)” on page 17).
5. For an iBox BT or iBox BT LE using Bluetooth, press up on the bottom of the iBox device to turn
on Bluetooth.
For a classic iBox, press the eKEY Fob power button until the green light flashes and point the fob at the iBox.
Note: You have up to five (5) minutes after starting the operation to aim the fob at the iBox or to push
up on the bottom of the iBox BT or iBox BT LE. This gives an opportunity to enter the PIN in the
car and then walk up to the door.
6. Upon success, press up on the bottom of the iBox to release the key container. The key
container will relock after 30 seconds.
7. If a business card, agent notes, or a listing flyer is programmed into the iBox, the information
displays on the phone or tablet. Drag down to see any additional information.
The Android device connects to the network and sends the showing information immediately after the Obtain Key function is complete.
Figure 13. Obtain Key
15
Chapter 3
Access iBox
Place Listing Keys in the iBox
The classic iBox key container holds up to three (3) listing keys. The iBox BT and iBox BT LE key
containers hold up to five (5) listing keys or two (2) gate cards and two (2) keys. Before closing the key
container, verify that all items are well inside and the front is not bowing or bulging out. Listing agents
should always make sure there is a spare set of listing keys before closing the key container.
Caution: Do not place ID tags, key rings, or loose objects in the key container. They can jam the container.
To close the key container, turn the key container to face you, see the figure below. Insert the key
container into the bottom of the iBox and push up until it closes.
Figure 14. Key Container
Feedback
If the iBox is set by the listing agent to ask for feedback after a listing is shown, a feedback alert screen
is displayed after the key container is opened. This gives an opportunity to provide feedback about the
showing to the listing agent. If Ignore is selected, no feedback is sent to the listing agent.
Select Leave Feedback to enter feedback information to send to the listing agent. For example, select
where you heard about the listing, the level of interest in the property, whether the listing price is within
the buyer’s range, and enter any notes about the showing.
16
Chapter 3
Access iBox
Figure 15. Leave Feedback
The feedback is delivered to the Supra network the next time the eKEY software updates. The listing
agent can view the feedback at SupraWEB.
Only the listing agent can activate or deactivate the feedback setting in an iBox (see “Change iBox
Settings” on page 24).
Showing Hours
iBox devices can be set to allow 24-hour access or timed access for specific hours. To determine the
timed access hours preset for iBox devices in the area, contact the Association or MLS.
Showing hours are in standard time. If the area observes daylight saving time, the actual access hours
are one hour later than the hours set in the iBox during daylight saving time. For example, if an iBox
is set for access from 8 a.m. to 9 p.m. Standard Time, during daylight saving time, the actual showing
hours are 9 a.m. to 10 p.m.
Set the iBox to allow 24-hour access or to limit access to during the timed access hours. Customize
the showing hours and set different access hours for weekdays, Saturday, and Sunday. Follow the
instructions in “Change iBox Settings” on page 24 to change the iBox showing hours.
Call Before Showing (CBS)
Call Before Showing (CBS) allows the listing agent to control access by requiring the buyer’s agent to
call the listing agent to obtain a CBS code.
Every iBox contains a CBS code that can be enabled (see “Change iBox Settings” on page 24).
This code must be entered into the buyer’s agent’s key to open the iBox. Contact the listing agent to
determine if a CBS code is required to open an iBox.
17
Chapter 3
Access iBox
If the iBox requires a CBS code, the code must be entered into the eKEY software before releasing the
key container and it must be entered each time the key container is released (see “Release the Key
Container” on page 15).
Open an iBox that requires a CBS code:
1. Follow the steps to “Release the Key Container” on page 15.
2. If CBS is required, an error tone sounds and the “CBS Required” screen displays. Enter the
CBS code and select Continue.
Figure 16. CBS Required
Cooperating
There may be an option to access an iBox in a neighboring Association/MLS. Check with your
Association/MLS to determine if there is a cooperating agreement in place.
Show listings in a cooperating area:
•
The eKEY software must be programmed to allow access to iBox devices in cooperating areas.
•
The cooperating Association/MLS must give permission to update the eKEY for their area.
Your Association/MLS can give permission to access cooperating areas into your eKEY software. Once
the programming is added to your eKEY software, contact the cooperating Association/MLS to receive
permission to update your eKEY software for their system.
After both steps are completed and when the eKEY software does an automatic update, it will update
the primary system and the cooperating system. If a manual update is performed to the eKEY software
by entering an update code, first update the primary Association/MLS and then update the cooperating
areas.
18
Chapter 3
Access iBox
Release the Shackle
Each iBox has a four-digit shackle code that is used to release the shackle for placing it at a listing or
removing it from a listing.
Release the shackle on an iBox:
Note:
For an iBox BT and iBox BT LE, press down on the shackle with one hand while supporting the bottom of the iBox device with the other hand. Then pull up on the shackle to remove it completely from the iBox device. For a classic iBox, the shackle pops open. To remove the shackle completely, perform steps 1-6 while providing upward pressure on the shackle.
1. Select the eKEY icon to open the eKEY application.
2. Select Open Shackle.
3. Enter the shackle code.
4. Uncheck the Add to Inventory box, if desired.
5. Select a Reason and press Begin.
Note: If “Adding a New Listing” is selected, the “Assign Listing” box appears.
Figure 17. Open Shackle
6. For an iBox BT or iBox BT LE, press up on the bottom of the device to turn on Bluetooth.
For a classic iBox, press the eKEY Fob power button until the green light flashes and point it at
the iBox.
7. For an iBox BT and iBox BT LE, press down on the shackle with one hand while supporting
the bottom of the iBox device with the other hand. Then pull up on the shackle to remove it
completely from the iBox device.
For a classic iBox, the shackle pops open. To remove the shackle completely, repeat steps the
above steps 1-6 while providing upward pressure on the shackle.
8. Upon success, the shackle releases and the battery level in the iBox is shown on the eKEY app.
19
Chapter 3
Access iBox
After the first time the shackle is released a request to assign a Listing ID to the keybox is displayed. If Assign is selected, enter the listing ID for the iBox.
When the shackle is released, the iBox device is automatically added to the inventory unless the Add to Inventory box is unchecked. The Keybox Details screen displays and the settings can be edited
in the iBox. Immediately after releasing the shackle the eKEY software connects to the network and
sends the current inventory information about the iBox (see “iBox Inventory” below).
iBox Inventory
To view the iBox inventory, select the Inventory icon on the main eKEY screen.
View iBox Inventory and Detail Information
1. Open the eKEY application.
2. Select Inventory and a list of the iBox devices are displayed. If the iBox is assigned to a listing,
the listing ID number is shown in bold above the address.
3. Select an iBox from the list to view detailed information.
Figure 18. View iBox Inventory
20
Chapter 3
Access iBox
Add an iBox to Inventory
To receive real-time showing notifications on the Android device, add the iBox to the inventory and edit
the settings in the iBox. The iBox device must be present to add it to the inventory.
Release the shackle on an iBox and the iBox is automatically added to the inventory unless the Add to inventory box is unchecked.
Add an iBox to inventory:
1. Open the eKEY application.
2. Select Add Keybox.
3. Enter the shackle code and select Begin.
4. For an iBox BT or iBox BT LE, press up on the bottom of the device to turn on Bluetooth.
For a classic iBox, press the eKEY Fob power button until the green light flashes and point it at
the iBox.
Upon success, the iBox is added to the inventory on the eKEY software. The iBox is added to inventory
at SupraWEB during the next eKEY update.
Immediately update the iBox inventory at SupraWEB:
1. Select the Back button to go to the Keybox Details screen.
2. Select the Back button to return to the eKEY main screen.
3. Select the Update icon to update the iBox inventory at SupraWEB.
Once eKEY has completed the update, the new iBox is added to the inventory on SupraWEB.
Figure 19. Add Keybox
21
Chapter 3
Access iBox
Delete an iBox from Inventory
1. Open the eKEY application.
2. Select Inventory.
3. Select the iBox from the list.
4. Select Delete.
5. Select Yes to confirm.
After confirming, the iBox is then deleted from inventory on the eKEY software. The iBox is deleted
from inventory at SupraWEB during the next eKEY update.
Immediately delete the iBox at SupraWEB:
1. Press the back arrow to return to the main eKEY screen.
2. Press the Menu button.
3. Select Update Key from the list to update the iBox inventory at SupraWEB.
After the key has completed the update, the iBox is deleted from inventory at SupraWEB.
Figure 20. Delete iBox From Inventory
Read Activity
The iBox stores a showing record each time the key container is released. The iBox records the date
and time the property was shown and the buyer’s agent’s name, key serial number, and phone number.
View the showings that are stored in an iBox and display them on the Android device by reading the
iBox activity.
22
Chapter 3
Access iBox
Read an iBox:
1. Open the eKEY application.
2. Select Read Activity.
3. Enter the iBox shackle code and select Begin.
4. For an iBox BT or iBox BT LE, press up on the bottom of the device to turn on Bluetooth.
For a classic iBox, press the eKEY Fob power button until the green light flashes and point the
fob at the iBox.
Note: The iBox reads and delivers the showings to the Android device then number of showings in the iBox are displayed.
5. Select Done to view the showings.
6. Select a listed showing to view the detailed information.
7. Select the phone number to call the buyer’s agent, optional.
Figure 21. Keybox Activity
View Showing Activity
After an iBox is read, the showing activity is stored in the iBox and can be viewed at any time.
View showing activity:
1. Open the eKEY application.
2. Select Inventory.
3. Select the iBox from the list.
4. Select Activity.
5. Select a showing to view detailed information about the showing.
23
Chapter 3
Access iBox
Delete Showing Activity
Delete an iBox showing activity stored in the Android device:
1. Open the eKEY application.
2. Select Inventory.
3. Select the iBox from the list.
4. Select Activity.
• To delete all of the showing activity for the iBox, select the Menu button on the Android device and select Delete All.
• To delete a particular showing, select the showing, then select the Menu button on the Android device and select Delete.
Change iBox Settings
To change the settings of an iBox that is in inventory, the iBox is required to be present to save the new
settings to it (see “Table 1. iBox Settings and Description” on page 25). The old shackle code is
required to change the shackle code.
1. Open the eKEY application.
2. Select Inventory and an iBox inventory list displays.
3. Select an iBox from the list to view the settings.
Note: If the iBox is not in inventory see “Add an iBox to Inventory” on page 21.
4. Select the Edit button.
5. Select the field to change, update the information.
6. Select Program.
7. Enter the old shackle code for the iBox and select Begin.
8. For an iBox BT or iBox BT LE, press up on the bottom of the device to turn on Bluetooth.
For a classic iBox, press the eKEY Fob power button until the green light flashes and point it at
the iBox.
Once the programming has completed, the screen will show the updated values.
24
Chapter 3
Access iBox
Figure 22. Change iBox Settings
Table 1.
iBox Settings and Description
Setting
Description
Shackle code
Code used to release the shackle on the iBox
Require Feedback
Prompt for feedback after a showing
Require CBS
Turn on to require a CBS code be entered to open the iBox
Timed Access
Toggle between 24-Hour and Timed Access hours
Access Hours
If Timed Access is on, can adjust hours for weekdays, Saturdays, and Sundays
Listing Information
Information about the listing; update the listing ID, listing date, address, MLS name,
client, and occupant
Business card
Listing agent’s business card information; displayed to eKEY users when they open the
iBox
Agent Note
Notes to the buyer’s agent; displayed to ActiveKEY and eKEY users when they open the
iBox
Listing Flyer
Features or information about the listing; displayed to eKEY users when they open the
iBox
25
Chapter 4
MLS Listings and Roster
Chapter 4 MLS Listings and Roster
This chapter explains how to set up the market area, search and view listings,
create saved searches, and search and view the agent roster.
In this chapter:
eKEY Professional................................................................................. 27
Settings for eKEY Professional.......................................................... 27
Listings.................................................................................................... 28
Market Area........................................................................................ 28
Update Listings................................................................................... 30
View Listings....................................................................................... 30
Delete Listings.................................................................................... 35
Roster...................................................................................................... 36
View Roster........................................................................................ 36
Delete Roster..................................................................................... 37
26
Chapter 4
MLS Listings and Roster
eKEY Professional
With the eKEY Professional software view MLS listing and roster information on the Android device.
There are five (5) additional icons on the eKEY home screen for eKEY Professional:
•
Market Area – Define the listings to download and view on the Android device
•
Listings – Search and view listings
•
Roster – Search and view the agent roster
•
Hotsheets — View Hotsheets listings
•
Showings – View showing activity for your listings
Important! A subscription to eKEY Professional service is required to view MLS data in the eKEY
software. Contact the Association/MLS to change the subscription.
Figure 23. eKEY Professional Home Screen
Settings for eKEY Professional
There are some settings available only for eKEY Professional subscribers.
View or change the eKEY Professional settings:
1. On the Android, open the eKEY application.
2. Select Settings located on the second page of icons in eKEY Professional.
27
Chapter 4
MLS Listings and Roster
Figure 24. eKEY Professional Settings
3. Uncheck Download Roster to stop the agent roster from downloading to the Android device.
4. Uncheck Download Listings to stop listings from downloading to the Android device.
5. Select the Save button to save your changes.
Listings
With eKEY Professional service, view MLS listings on the Android. The listing information is
downloaded to the Android the next time the eKEY application is opened, once per day. If the market
area is not set up after the Listings icon is selected, a prompt to configure the market area will display.
Market Area
The market area determines which listings are downloaded and viewable on the Android. Define the
market area first, then view listings on the device. Change the market area as often as needed.
Important! Active cellular/data coverage is required to define the market area and download listings.
Once the listings are downloaded, cell/data coverage is not required to view them.
Tip:
Select only commonly used listings for the market area to speed up listing searches and
updates.
Set up the market area:
1. Open the eKEY application.
2. Select the Market Area icon.
3. Select Area, Class, Status, and a Price range to choose the market area. At least one Area,
Class, and Status selection is required.
28
Chapter 4
MLS Listings and Roster
Figure 25. Configure Market Area
4. Select Save.
5. Enter your 4-digit PIN code to save the market area and select Begin.
6. Select Download to download the listings in the market area to the Android.
Figure 26. Downloading Listings
29
Chapter 4
MLS Listings and Roster
Update Listings
Once market area is set up, the listings and roster are updated once daily the first time the eKEY
application is opened, each day, (see “Chapter 2 Updating” on page 8).
Important! The listings are pulled from the MLS to the Supra network daily. Updating the eKEY software more than once a day will not update the listings.
View Listings
There are several ways to view the MLS listings in the eKEY software.
•
Quick Search – Search for listings by address, zip code, or MLS ID number
•
Custom Search – Search for listings that match specific criteria
•
Hotsheets — View Hotsheets listings
•
My Listings – View personal listings
•
Saved Searches – Create and save custom searches
Figure 27. Listings Options
Quick Search
Quickly search for listings by entering part or all of a street address or MLS ID, or by zip code.
Quick search of the listings in the market area:
1. Open the eKEY application.
2. Select the Listings icon.
3. Select Quick Search.
4. Enter part or all of street address, zip code, or MLS ID number and the listings that match are
displayed in ascending price order.
5. Select a listing to view detailed information.
30
Chapter 4
MLS Listings and Roster
Figure 28. Quick Search
Hotsheets
Hotsheets displays new listings or listings that have had a change to their price or status in the last
three (3) days.
Display listings in the market area that are on the Hotsheets:
1. Open the eKEY application.
2. Select the Hotsheets icon and the Hotsheets listings within the market area are displayed.
Note: Another option is to select the Listings icon and then select Hotsheets.
3. Select a listing to view detailed information.
Figure 29. Hotsheets List and Hotsheets with a New Price
31
Chapter 4
MLS Listings and Roster
My Listings
My Listings displays all of the listings within the market area that was selected.
Display personal listings:
1. Open the eKEY application.
2. Select the Listings icon.
3. Select My Listings and all of the personal listings within the market area that was selected are
displayed.
4. Select a listing to view detailed information.
Custom Search
Search for specific listings in the selected market area. For specific search results, select additional
search criteria and save the custom search.
Perform a custom search:
1. Open the eKEY application.
2. Select the Listings icon.
3. Select Custom Search.
4. Select the criteria for the search: choose specific criteria from a list for some fields, select a
range, or input specific text.
5. Select the search button in the upper right corner of the screen and all of the listings within the
selected search criteria and market area are displayed.
6. Select a listing to view detailed information.
Tip: If more than 500 searched records are returned, only the top 500 listings are displayed. Narrow the search criteria to limit the listings returned.
Figure 30. Custom Search
32
Chapter 4
MLS Listings and Roster
Listing Details
Listings that match the search criteria are displayed in a list view. The listings are sorted by price in
ascending order. Hotsheets listings are noted with a hotsheets icon.
Figure 31. Listing Search Results
To view details about a particular listing, select the listing. Scroll down to view additional information.
Figure 32. Listing Detail View
33
Chapter 4
MLS Listings and Roster
From the detail view:
•
Select an agent name to view detailed information about the agent
•
Select an address to view a map to the listing in Google Maps™
•
Call the listing agent by selecting the agent’s phone number
•
Email the listing agent by selecting the agent’s email address
Figure 33. Map View
Saved Searches
Saved searches are custom searches that are saved. Tapping a saved search runs the search and
returns the results.
Create a saved search:
1. Open the eKEY application.
2. Select the Listings icon.
3. Select Custom Search.
4. Select the criteria for your search.
Tip:
To clear any search criteria entered, select Clear All at the bottom of the screen.
5. Select Save.
6. Enter a name for the search.
7. Enter any notes about the search.
8. Select OK.
34
Chapter 4
MLS Listings and Roster
Run a saved search:
1. Open the eKEY application.
2. Select the Listings icon and the list of saved searches created is displayed.
Figure 34. List of Saved Profiles
3. Select the saved search and the listings in the market area that match the criteria selected for
the saved search are displayed.
Edit or delete a saved search:
1. Open the eKEY application.
2. Select the Listings icon and the list of saved searches created is displayed.
3. Select the arrow to the right of the saved search name.
4. Make any changes to the custom search and select Save or select Delete to delete the saved
search.
Delete Listings
Delete listings off of the Android:
1. On the Android, open the eKEY application.
2. Select Settings located on the second page of icons.
3. Select the Menu button.
4. Select Delete Listings.
5. Select Yes to confirm to delete the listings.
35
Chapter 4
MLS Listings and Roster
Roster
The eKEY software provides a roster of the members in the Association/Board/MLS. The roster data is
updated during the first eKEY software update of any given day.
View Roster
1. On the Android, open the eKEY application.
2. Select the Roster icon.
3. To search for an agent, enter part or the agent’s entire name.
The eKEY software automatically filters and displays the search results as the search criteria is
entered. The eKEY software will display the first name, last name, or office name of any agent that
meets the entered search criteria.
Figure 35. Roster Search and View
4. Roster entries with an email
information is available.
or phone
icon next to their name indicate email or phone
• To view the detailed contact information, select the agent.
• To contact the agent, select the phone number or email address shown.
36
Chapter 4
MLS Listings and Roster
Figure 36. Agent Details
Delete Roster
Delete the Roster off of the Android:
1. On the Android, open the eKEY application.
2. Select Settings, located on the second page of icons.
3. Select the Menu button on your device.
4. Select Delete Roster.
5. Select Yes to confirm to delete the roster.
37
Chapter 5
Showing Activity
Chapter 5 Showing Activity
This chapter explains showing notifications and describes how to view
showing activity using the eKEY software.
In this chapter:
Showing Activity..................................................................................... 39
Voice Report....................................................................................... 39
Showing Notifications and Messages................................................. 39
Showings Activity on Android Devices................................................ 41
Disable eKEY Showing Notifications.................................................. 42
Update Listing ID................................................................................ 42
38
Chapter 5
Showing Activity
Showing Activity
The eKEY software records activity each time a key container is opened and sends the information to
the Supra network.
As a listing agent, there are several ways to see who has shown your listings. As a buyer’s agent, you
can also get a report of how many properties you’ve accessed.
Ways to view show activity:
•
Read an iBox to view its showing activity on the Android (see “Read Activity” on page 22)
•
Go to the SupraWEB to see the showing activity on your listings or get a report of all the
showings you’ve done (see the SupraWEB Guide available at www.supraekey.com under
Customer Support and pick SupraWEB Resources)
•
With eKEY Professional service, view the showing activity on an Android phone or tablet
•
Request a report from the KIM voice system (see below)
Voice Report
Request a showing activity report using KIM voice access. The iBox serial number and shackle code
are required to request the report. Choose to request a voice or e-mail report. An email report is
delivered to the email address on record with the Association, Board, or MLS.
Request an activity report from KIM voice:
1. Call KIM voice at 888-968-4032.
2. On the Android keypad, enter the eKEY software serial number and PIN code, then press #.
3. Select option 5 from the voice menu.
4. Press 1 for a voice report or 2 for an email report.
5. Follow the instructions to receive the report.
Showing Notifications and Messages
Showing notifications automatically display in the eKEY software whenever an iBox in inventory is
shown. Messages sent from Supra, your Board/Association/MLS, or your office broker also are
automatically displayed.
39
Chapter 5
Showing Activity
Figure 37. eKEY Notification
Messages and showing notifications can also be viewed later.
View messages:
1. Open the eKEY application.
2. Select Messages.
The number of showings displayed is an accumulation of showings at your listings in the last 14 days.
Figure 38. Messages
40
Chapter 5
Showing Activity
Showings Activity on Android Devices
With the eKEY Professional service, showing data is delivered to the eKEY software on the phone or
tablet.
View showing activity on the Android:
1. Open the eKEY application.
2. Select the Showings icon and the showing activity for the previous seven (7) days is displayed.
3. Select a showing to view detailed information about the showing.
Figure 39. Showing Information
From the Showing Details screen:
•
Select the agent name to display the agent’s information from the roster
•
Select the agent’s phone number to call the listing agent, or
•
Select the iBox to view it in the keybox inventory
Change the number of days activity shown in the eKEY software:
1. On the computer navigate to www.supraekey.com.
2. Select Agents-Log on to SupraWEB.
3. Enter the user ID and password and select Login.
Note: To register for a single sign on (SSO) user ID and password, click the Register button.
4. Select Settings.
5. Select eKEY Showings.
6. Select the number of days of showing activity to be displayed in your eKEY software.
41
Chapter 5
Showing Activity
Disable eKEY Showing Notifications
Disable the automatic showing notifications:
1. Open the eKEY application.
2. Select Settings.
Note: With eKEY Professional, the Settings icon is on the second page of icons.
3. Uncheck the eKEY Notifications option.
4. Select the Back button on the Android to return to the eKEY main screen.
Figure 40. Disable eKEY Notifications
Update Listing ID
Update the listing ID whenever an iBox is placed on a listing or removed from a listing to keep the iBox
showing reports accurate.
To update the listing ID when placing an iBox on a listing see “Change iBox Settings” on page 24,
or enter the listing ID at SupraWEB by selecting the iBox from the Assign Listing link in the QUICK
LINKS section and enter the information.
42
Chapter 6
Support and Troubleshooting
Chapter 6 Support and Troubleshooting
This chapter provides information to help troubleshoot problems and contact
technical support for assistance with the eKEY software.
In this chapter:
Support.................................................................................................... 44
Training Library................................................................................... 44
Help Screens...................................................................................... 45
43
Chapter 6
Support and Troubleshooting
Support
Need assistance troubleshooting the eKEY software? Support is available from 5 a.m. to 7 p.m. Pacific
Time, seven days a week.
Website
http://www.supraekey.com
Email
suprasupport@fs.utc.com
Telephone877.699.6787
Fax
503.589.8677
Call Support directly from the eKEY software on the Android device:
1. Open the eKEY application.
2. Select About.
3. Select the phone number shown in the Support Information section to call Support.
Figure 41. Contacting Support
Training Library
Another great resource for assistance with your eKEY software is our training library, available to all
agents.
Access the library:
1. Go to www.supraekey.com
2. Scroll down and select the Customer Support link.
Document and video training available here is periodically updated and we encourage you to bookmark
this page for future reference.
44
Chapter 6
Support and Troubleshooting
Help Screens
Help information is provided in the eKEY software. Select the Help icon on the second page of the
eKEY software menu screen to access the help information.
Figure 42. Help Icon
In addition, several screens throughout the eKEY software have an
shown in the upper right corner.
Select the
for help. Scroll through the different categories to see more.
Figure 43. Help Screen
45