Quadra-Fire CB1200-i

Transcription

R
CB1200-I PELLET INSERT
Owner’s Manual
Installation and Operation
O-T L
Tested and
Listed by
C
Portland
Oregon USA
US
OMNI-Test Laboratories, Inc.
Model:
CB1200I-B
NOTICE
• Important operating and • Read, understand and • Leave this manual with
follow these instrucparty responsible for use
maintenance instructions for safe installaand operation.
tions included.
tion and operation.
WARNING
WARNING
Please read this entire manual
before installation and use of this
pellet fuel-burning room heater.
Failure to follow these instructions
could result in property damage,
bodily injury or even death.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
• Do not overfire - If any external part starts to
glow, you are overfiring. Reduce feed rate.
Overfiring will void your warranty.
• Comply with all minimum clearances to combustibles as specified. Failure to comply may
cause house fire.
HOT SURFACES!
Glass and other surfaces are
hot during operation AND
cool down.
Hot glass will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fireplace.
• Alert children and adults to hazards of high
temperatures.
High temperatures may ignite clothing or other
flammable materials.
• Keep clothing, furniture, draperies and other flammable
materials away.
CAUTION
CAUTION
Tested and approved for wood pellets and shelled
field corn fuel only. Burning of any other type of fuel
voids your warranty.
www.quadrafire.com
T
O
N RD
O A
D SC
I
D
DO NOT DISCARD THIS MANUAL
Check building codes prior to installation.
• Installation MUST comply with local, regional, state and national
codes and regulations.
• Consult local building, fire officials or authorities having jurisdiction about restrictions, installation inspection, and permits.
7014-083E
September 1, 2008
R
CB1200-I Pellet Insert
and Welcome to the Quadra-Fire Family!
Hearth & Home Technologies welcomes you to our tradition
of excellence! In choosing a Quadra-Fire appliance, you
have our assurance of commitment to quality, durability, and
performance.
This commitment begins with our research of the market,
including ‘Voice of the Customer’ contacts, ensuring we
make products that will satisfy your needs. Our Research
and Development facility then employs the world’s most
advanced technology to achieve the optimum operation of
our stoves, inserts and fireplaces. And yet we are old-fashioned when it comes to craftsmanship. Each unit is meticulously fabricated and surfaces are hand-finished for lasting
beauty and enjoyment. Our pledge to quality is completed
as each model undergoes a quality control inspection.
From design, to fabrication, to shipping:
We wish you and your family many years of enjoyment in
the warmth and comfort of your hearth appliance. Thank
you for choosing Quadra-Fire.
CLEARANCE TO COMBUSTIBLES LABEL LOCATED INSIDE HOPPER LID
SERIAL NUMBER & MANUFACTURE DATE LABEL LOCATED UNDER TOP ON INSIDE OF HOPPER BODY
CAUTION:
HOT WHILE IN OPERATION DO NOT TOUCH. KEEP CHILDREN, CLOTHING AND FURNITURE
AWAY. CONTACT MAY CAUSE SKIN BURNS. SEE NAMEPLATE AND INSTRUCTIONS. Operate this unit
with fuel hopper lid closed. Failure to do so may result in emissions products' combustion from the hopper
under certain conditions. Maintain hopper seal in good condition. Do no over fill the hopper.
ATTENTION:
CHAUD LORS DE L'OPÉRATION. NE PAS TOUCHER. GARDEZ LES ENFANTS ET LES VÊTEMENTS LOIN DE
L'ESPACE DÉSIGNÉ DE L'INSTALLATION. LE CONTACT PEUT CAUSER DES BRÛLURES À LA PEAU. VOIR L'ÉTIQUETTE ET LES
INSTRUCTIONS. Opérez cet appareil avec le couvercle de la trémie fermé. Le défaut de ne pas suivre les instructions peut résulter,
sous certaines conditions, en une combustion des émissions des produits venant de la trémie. Ne pas remplir la trémie trop pleine.
Test Lab &
Report No.
Safety and clearance section located on inside of hopper lid./Serial Number section located under top on inside of hopper body.
La section se réfé dux distances et mescres de sécurité est située à l'intérieut du couvércle de la tré la bôitre à feu. La section du numéro de série est située en dessous du couvercle à l'intérieur de la trémie.
R
Portland
Oregon USA
O-T L
US
C
Report / Rapport
#061-S-13-2
1200-I Pellet Insert
OMNI-Test Laboratories, Inc.
Listed Solid Fuel Room Heater/Pellet Type Insert. Also suitable for
Mobile Home Installation. This appliance has been tested and listed for
use in Manufactured Homes in accordance with OAR 814-23-9000
through 814-23-909.
Appareil de chauffage inséré de combustible solide/de type de boulettes. Accepté dans
l'installation dans les maisons mobiles. Cet appareil a été testé et enregistré pour
l'usage dans les Maisons Mobiles en accord avec OAR 814-23-9000 jusqu'à 814-23-909.
Model Name
Testé à: ASTM E1509-95, UL127, ULC628-M93, ULC S610-M87, ULC/ORD
C1482-M1990, Room Heating Pellet Burning Type, (UM) 84-HUD POUR USAGE
AVEC LES BOULETTES DE BOIS OU DE COMBUSTIBLE DE MAIS ÉCOSSÉ DES
CHAMPS.
Consommahon maximale à l'entrée (sans pertes) 2.5 kg/h.
Puissance Électrique: 115 VAC, 60 Hz, Début 4.1 Amps, Courir 1.1 Amps,
Éloignez le fil électrique de l'appareil. Ne pas faire passer le fil électrique au
dessus ou en dessous de l'appareil.
DANGER: Il y a risque de décharge électrique. Déconnectez le fil électrique de la
prise de contact avant le service.
Remplacez la vitre seulement avec une vitre céramique de 5 mm disponible chez
votre fournisseur.
Pour allumer, monter la température du thermostat au dessus de la température de
la pièce, le poêle s'allumera automatiquement. Pour éteindre, descendre la
température du thermostat en dessous de la température de la pièce. Pour des
instructions supplémentaires, référez vous au manuel du propriétaire. Gardez la
porte d'ouverture et la porte des cendres fermées hermétiquement durant
l'opération.
SA
M
PL
Tested to: ASTM E1509-95, UL127, ULC S628-93, ULC S610-M87,
ULC/ORD C1482-M1990, Room Heating Pellet Burning Type, (UM) 84-HUD
FOR USE ONLY WITH PELLETIZED WOOD OR SHELLED FIELD CORN FUEL.
Input Rating Maximum 5.5 lb fuel/hr.
Electrical Rating: 115 VAC, 60 Hz, Start 4.1 Amps, Run 1.1 AMPS.
Route power cord away from unit. Do not route cord under or in front of
appliance.
DANGER: Risk of electrical shock. Disconnect power supply before
servicing. Replace glass only with 5mm ceramic available from your dealer.
To start, set thermostat above room temperature, the stove will light
automatically. To shutdown, set thermostat to below room temperature. For
further instruction refer to owner's manual.Keep viewing and ash removal doors
tightly closed during operation.
1445 Highway North, Colville, WA 99114
www.quadrafire.com
E
Tested and
Listed by
Masonry or Zero Clearance Minimum Clearances to Combustible
MANTEL
SIDE WALL
B
Maçonnene ou zéro distance foyer distances minimales à tout matériel combustible.
A Louvers to combustible wall 6” (152mm) A Lucarne au mur combustible
12” (305mm) B Dessus de l'insert à la tablette de cheminée
B Insert top to mantel
C Revêtement facial
3” (76mm)
C Front Facing
6" (152mm) D* Protechion de sol - frontal
D* Hearth Extension - Front
E* Protechon ole sol - côté
8” (203mm)
E* Hearth Extension - Side
C
A
*See hearth protection note above
E
*Voir les notes sur la protechion ole sol ci-dessus.
DO NOT REMOVE THIS LABEL / NE PAS ENLEVER L'ÉTIQUETTE
D
U.S. ENVIRONMENTAL PROTECTION AGENCY
FEB
MAR APR
MAY JUNE JULY AUG SEPT OCT NOV
DO NOT REMOVE THIS LABEL / NE PAS ENLEVER L'ÉTIQUETTE
Page 2
DEC
7014-080C
Manufactured Date
QUADRA-FIRE
OMNI Test Laboratories, Inc., Beaverton, Or Report/Rapport 061-S-12-2
This model is exempt from EPA certification under 40 CFR 60.531 by definition [Wood Heater (A) "Air-to-Fuel Ratio"].
2008 2009 2010 JAN
152mm
305mm
76mm
152mm
203mm
1200-I PELLET INSERT
SERIAL NO. / NUMÉRO DU
007C
Made in China/Fait Aux Chine
Serial Number
7014-080C
7014-083E
September 1, 2008
R
TABLE OF CONTENTS
Section 1: Listing and Code Approvals
A.
B.
C.
D.
E.
Section 8: Operating Instructions
Appliance Certifications ......................4
Mobile Home Approved ......................4
Glass Specifications ............................4
Electrical Rating ..................................4
BTU & Efficiency Specifications ..........4
A.
B.
C.
D.
E.
F.
G.
H.
Section 2: Getting Started
A. Design, Installation & Location
Considerations ....................................5
B. Fire Safety ..........................................5
C. Tools & Supplies Needed ...................6
D. Inspect Appliance, Components
and Pre-Check List .............................6
Fuel Size & Material ............................25
General Operation Information ...........25
Before Your First Fire .........................26
Starting Your First Fire........................26
Fire Characteristics .............................26
Feed Rate Adjustment .......................26
Ignition Cycles ....................................26
Frequently Asked Questions...............27
Section 9: Troubleshooting ............................28-30
Section 10: Maintaining & Servicing Appliance
A.
B.
C.
D.
E.
F.
G.
Section 3: Dimensions & Clearances
A. Appliance Dimensions ........................7
B. Clearances to Combustibles
As A Built-In, UL and ULC ..................8
C. Clearances to Combustibles,
Masonry & Zero Clearance .................9
D. Minimum Opening for Factory
Built Fireplace .....................................9
E. Masonry Minimum Opening ................10
F. Floor Protection ..................................10
G. Calculating Alternate Floor
Protection Material ..............................10
H. Removing Floor of Factory Built
Fireplace .............................................11
Proper Shutdown Procedure ...............31
Quick Reference Maintanence Chart ..31
General Maintenance & Cleaning .......31-34
High Ash Content Maintenance ..........35
Glass Replacement .............................36
Igniter Replacement ............................37
Baffle Removal ....................................37
Section 12: Reference Material
A.
B.
C.
D.
E.
F.
Component Functions.........................38-39
Component Locations .........................40
Exploded Drawings .............................41-42
Service Parts & Accessories...............43-45
Warranty Policy...................................46-47
Contact Information ............................48
Section 4: Vent Information
Chimney & Exhaust Connections ........12
B. Venting Termination Requirements ....12
C. Equivalent Feet of Pipe.......................13
D. Pipe Selection Chart ...........................13
A.
Section 5: Venting Systems
A. Direct Connect with Outside Air ..........14
B. Direct Connect without Outside Air .....14
C. Full Reline with Outside Air .................15
Section 6: Mobile Home ..................................16
Section 7: Appliance Set-Up
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
Rear Shroud Installation .....................17-18
Outside Air Kit .....................................19
Adjustable Hopper Option...................19
Grille Installation .................................19
Adjustable Hearth Support..................20
Panel & Trim .......................................21-22
Brick Set Installation ...........................23
Brick Clip Installation ...........................23
Log Set Placement ..............................24
Thermostat Installation ........................24
Septemer 1, 2008
7014-083E
Page 3
R
1
Listing and Code Approvals
A. Appliance Certification
E. BTU & Efficiency Specifications
MODEL:
1200-I Pellet Insert
Emissions Rating:
.9 grams/hr
LABORATORY:
OMNI Test Laboratories, Inc
*BTU Output:
14,000 - 40,000 / hr
REPORT NO.
061-S-13-2
Heating Capacity:
TYPE:
Solid Fuel Room Heater/Pellet Fuel
Burning Type Insert
up to 2,500 sq. ft. depending
on climate zone
Hopper Capacity:
60-75 lbs
Fuel:
Wood Pellets or Shelled Corn
STANDARD:
ASTM E1509-95, ULC S628-93, ULC
S610-M87, ULC S628-M93 and ULC/
ORD-C1482-M1990 Room Heater Pellet
Fuel Burning Type and (UM) 84-HUD,
Mobile Home Approved
*BTU output will vary, depending on the brand of fuel you
use in your appliance. Consult your Quadra-Fire dealer
for best results.
B. Mobile Home Approved
This appliance is approved for mobile home installations
when not installed in a sleeping room and when an outside
combustion air inlet is provided. The structural integrity of the
mobile home floor, ceiling, and walls must be maintained.
NOTE: Hearth & Home Technologies, manufacturer of
this appliance, reserves the right to alter its products,
their specifications and/or price without notice.
The appliance must be properly grounded to the frame of
the mobile home and use only listed pellet vent, Class “L” or
“PL” connector pipe. A Quadra-Fire Outside Air Kit must be
installed in a mobile home installation.
C. Glass Specifications
This appliance is equipped with 5mm ceramic glass. Replace
glass only with 5mm ceramic glass. Please contact your
dealer for replacement glass.
NOTE: This installation must conform with local codes. In
the absence of local codes you must comply with the ASTM
E1509-95, ULC S628-93, ULC S610-M87, ULC/ORD-C1482-M1990, (UM) 84-HUD.
D. Electrical Rating
115 VAC, 60 Hz, Start 4.1 Amps, Run 1.1 Amps
Page 4
7014-083E
September 1, 2008
R
2
Getting Started
A. Design, Installation & Location
Considerations
B. Fire Safety
1. Appliance Location
Consideration must be given to safety, convenience, traffic
flow, and the fact that the appliance will need a chimney and
chimney connector. It is a good idea to plan your installation
on paper, using exact measurements for clearances and floor
protection, before actually beginning the installation.
If you are not using an existing chimney, place the appliance
in a location to maintain a clear passage for the installation
of any listed and approved pellet venting system. This appliance may be vented vertically or horizontally.
Maintain specified vent clearance to comubstible requirements listed by the pellet manufactures venting instructions
and all clearance to combustivles listed in this manual.
Check with your local building code agency before you begin
your installation. Be sure local building codes do not supersede UL specifications and always obtain a building permit
so that insurance protection benefits cannot be unexpectedly
cancelled. If any assistance is required during installation,
please contact your local dealer.
We recommend that a qualified building inspector and your
insurance company representative review your plans before
and after installation.
Maintain the designated clearances to combustibles. Insulation must not touch the chimney. You must maintain the
designated air space clearance around the chimney. This
space around a chimney is necessary to allow natural heat
removal from the area. Insulation in this space will cause
a heat buildup, which may ignite wood framing. NOTE:
Clearances may only be reduced by means approved
by the regulatory authority having jurisdiction.
To provide reasonable fire safety, the following should be
given serious consideration:
1.
Install at least one smoke detector on each floor of
your home to ensure your safety. They should be
located away from the heating appliance and close
to the sleeping areas. Follow the smoke detector
manufacturer’s placement and installation instructions,
and be sure to maintain regularly.
2.
A conveniently located Class A fire extinguisher
to contend with small fires resulting from burning
embers.
3.
A practiced evacuation plan, consisting of at least 2
escape routes.
4.
A plan to deal with a hopper fire as follows:
In the event of a hopper fire:
2. Thermostat Location
The thermostat’s location will have some effect on the
appliance’s operation. When the thermostat is located close
to the appliance, it may require a slightly higher temperature
setting to keep the rest of the house comfortable. If the
thermostat location is in an adjacent room or on a different
floor level, you will notice higher temperatures near the
appliance.
a.
b.
Evacuate the house immediately.
Notify fire department.
WARNING
CAUTION
• Do NOT connect this unit to a chimney flue servicing
another appliance.
• Do NOT connect to any air distribution duct or system.
Fire Risk.
•
•
Septemer 1, 2008
7014-083E
Do not operate appliance before reading
and understanding operating instructions.
Failure to operate appliance properly may
cause a house fire.
Page 5
R
D. Inspect Appliance & Components and
Pre-Use Check List
C. Tools And Supplies Needed
Tools and building supplies normally required
for installation, unless installing into an existing
masonry fireplace:
1.
Place the appliance in a location near the
final installation area and follow the procedures below:
2.
Open the appliance and remove all the parts
and articles packed inside the Component
Pack. Inspect all the parts and glass for shipping damage. Contact your dealer if any irregularities are noticed.
3.
All safety warnings have been read and followed.
4.
This Owner’s Manual has been read.
5.
Floor protection requirements have been met.
6.
Venting is properly installed.
7.
The proper clearances from the appliance and
chimney to combustible materials have been
met.
8.
The masonry chimney is inspected by a professional and is clean, or the factory built metal
chimney is installed according to the manufacturer’s instructions and clearances.
9.
The chimney meets the required minimum
height.
10.
All labels have been removed from the glass
door.
Fire Risk.
11.
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be
voided by, the following actions:
Plated surfaces have been wiped clean, if
applicable.
12.
Thermostat or remote has been installed.
13.
A power outlet is available nearby.
Reciprocating Saw
Hammer
Phillips Screw driver
Tape Measure
Plumb Line
Level
Framing Material
Hi-temp Caulking Material
Gloves
Safety Glasses
Framing Square
Electric Drill & Bits (1/4”)
1/4” Self-Tapping Screws
May also need:
Vent Support Straps
Venting Paint
WARNING
Inspect appliance and components for
damage. Damaged parts may impair safe
operation.
• Do NOT install damaged components.
• Do NOT install incomplete components.
• Do NOT install substitute components.
Report damaged parts to dealer.
WARNING
• Installation and use of any damaged appliance.
• Modification of the appliance.
• Installation other than as instructed by Hearth & Home
Technologies.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
• Operating appliance without fully assembling all
components.
• Do NOT Overfire.
Or any such action that may cause a fire hazard.
Page 6
7014-083E
September 1, 2008
R
3
Dimensions and Clearances
A. Appliance Dimensions
B
40" (1016mm)
29-1/4" (743mm)
22" (559mm)
8-3/4"
(222mm)
13" (330mm)
10-3/4"
(273mm)
A
12" (305mm)
28-1/2" (724mm)
Figure 7.1 - Top View
Figure 7.2 - Front View
Panel
A
B
Standard
30 inches (762mm)
40 inches (1016mm)
Large
33 inches (838mm)
50 inches (1270mm)
12"
(305mm)
13"
(330mm)
25-1/2"
(648mm)
11"
(279mm)
19-1/2" (495mm)
(Hopper Down)
30" (762mm)
22" (559mm)
(Hopper Up)
10-3/4"
(273mm)
11"
(279mm)
Figure 7.3 - Side View
Septemer 1, 2008
7014-083E
Page 7
R
B. Clearance To Combustibles, UL and ULC
AS A BUILT-IN
Rear Shroud Kit, Part 811-0680 is Required for Built-In Installation
(see pages 17-18 for installation instructions)
D
A
B
C
B
C
E
0 INCH (0mm) CLEARANCE TO EXPOSED SECTION AND FACE TRIM
Figure 8.1
A
Top of Shroud
Inches
Millime-
Top Vent
3.0
76
Rear Vent
0
0
0
0
B
Sides of Inside Shroud
Top or Rear Vent
C
Back of Inside Shroud
Top Vent
2.5
64
Rear Vent
0
0
3.0
76
0
0
D
Vent Pipe to Combustible
E
From Outside Edge of
Panel Set to Combustibles
Top or Rear Vent
INSTALLED AS A BUILT-IN UNIT
Shown with Rear Vent and Optional Outside Air
WARNING
Combustible
Mantel
Shown with Hopper Extended
12 in
Fire Risk.
Comply with all minimum clearances to combustibles as specified.
Failure to comply may cause
house fire.
6 in
Rear Shroud
Optional Outside
Air
NOTE:
• Illustrations reflect typical installations
and are FOR DESIGN PURPOSES
ONLY.
• Illustrations/diagrams are not drawn to
scale.
• Actual installation may vary due to
individual design preference.
Figure 8.2
Page 8
7014-083E
September 1, 2008
R
C. Minimum Clearances To Combustibles for
Masonry and Zero Clearance Fireplaces
MANTEL
Face Trim
SIDE WALL
B
C
Inches
Millimeters
A
Louvers to combustible
side wall
6
153
B
Insert top to mantel
12
305
C
Top to Face Trim
3
76
D
Hearth Extension - Front
6
153
E
Hearth Extension - Sides
8
203
A
D
E
Figure 9.1
D. Minimum Opening for Masonry and Zero
Clearance Fireplaces for Built-In Using
Rear Shroud
NOTE: A Quadra-Fire floor protector (Part 811-0730) is
available through your dealer to be used as a floor protector
for the section under the insert body only. Floor protection
to front and sides of insert unit must be supplied in addition
to this part.
Inches
Millimeters
22
558
15-1/2
393
25-1/2
647
Height - Rear Vent
22-1/2
571
Front Width
29-1/4
743
A
Rear Width
B
Depth
C* Height - Top Vent
D
C
B
*The size of your floor protector choice must be
added to this dimension. If using Quadra-Fire floor
protector, Part 811-0730, allow 1-1/2” (38mm).
A
D
Figure 9.2
Septemer 1, 2008
7014-083E
Page 9
R
E. Masonry Minimum Opening
G. Calculating Alternate Floor Protection Material
Thermal Conductivity: k value
The k value indicates the amount of heat (in BTU’s) that will flow
in 1 hour through 1 square foot of a uniform material 1 inch thick
for each degree (F) of temperature difference from one side of
the material to the other. The LOWER the k factor means less
heat is being conducted through the non-combustible material to
the combustible material beneath it. The k value of a material
must be equal or smaller then the required k value to be acceptable.
(BTU) (inch)
(foot2 (hour) (oF)
C
B
A
D
Thermal Resistance: R value
Inches
Millimeters
A
Rear Width
Location
22
558
B
Depth
13
330
C
Height - Top Vent
19-1/2
495
D
Front Width
29-1/4
743
The R value is a measure of a material’s resistance to heat
transfer. R value is convenient when more than one material is used since you can add the R values together, whereas
you can not do this for k value. The HIGHER the R factor
means less heat is being conducted through the non-combustible material to the combustible material beneath it. The
R value of a material must be equal or larger then the required R value to be acceptable.
Converting k to R:
Divide 1 by k and multiply the results times the thickness in inches of the material.
R = 1/k x inches of thickness
Converting R to k:
F. Floor Protection
Divide the inches of thickness by R.
1. Zero Clearance Installations*
It is necessary to install a floor protection of non-combustible material with a R value of 3.0 (1 inch [25mm] minimum
thickness with a “k” value of 0.58) or a 1 inch (25mm) air
space between insert base and hearth.
k = inches of thickness/R
Calculations:
Example: Floor protection requires k value of 0.84 and 3/4 inch
thick.
Alternative material has a k value of 0.6 and is 3/4 inch thick.
2. Non-Zero Clearance Installations*
A non-combustible floor protector is required with a minimum R value of 3.0 (1 inch [25mm] minimum thickness with
a “k” value of 0.58) extending 6 inches (153mm) in front of
the insert and 8 inches (203mm) to each side of the door
opening.
Divide 0.6 by .75 = k value of 0.80. This k value is smaller than
0.84 and therefore is acceptable.
* See alternate floor protection worksheet.
Page 10
7014-083E
September 1, 2008
R
H. Removing Metal Floor of Factory-Built
Firebox
•
The firebrick (refractory), glass doors, screen rails,
screen mesh and log grates can be removed from a
factory-built firebox in order to gain minimum insert
opening requirements.
•
Any smoke shelves, shields and baffles may be
removed from a factory-built firebox if attached with
mechanical fasteners.
•
The metal floor of the factory-built firebox may be
removed to facilitate the installation of the insert only
when a 1 inch (25mm) airspace is provided between
the insert and the floor of outer wrap.
•
If the floor is made of thin metal, we recommend using
a Quarda-Fire floor protector, Part 811-0730, which is
available through your dealer.
Keep sharp edge of
metal floor away from
power cord
Figure 11.3. Place the insert into the factory-built firebox. Ensure that the power
cord can not be damaged by the sharp metal
edge. You may need to cut out a notch to
accommodate the cord.
Starter hole
Mark area of
floor to cut
Figure 11.1. Measure and mark the metal
floor for cutting. With a drill, make a starter
hole in each corner.
Figure 11.2. Using a saws-all, cut out the
floor.
Septemer 1, 2008
7014-083E
Page 11
R
4
Vent Information
B. Venting Termination Requirements
A. Chimney and Exhaust Connection
1. Chimney & Connector: Use 3 or 4 inch (76-102mm)
diameter type "L" or "PL" venting system. It can be vented
vertically or horizontally.
2. Mobile Home: Approved for all Listed pellet vent. Use
Listed double wall flue connector. A Quadra-Fire Outside
Air Kit must be used with manufactured home installations.
3. Residential: Use 24 gauge single wall flue connector or
Listed double wall flue connector to Class A Listed metal
chimneys, or masonry chimneys meeting national and/or
local codes for solid fuel appliances.
CAUTION
Do not terminate vent in any enclosed or semi-enclosed
area such as a carport, garage, attic, crawl space, under a
sun deck or porch, narrow walkway or closely fenced area,
or any location that can build up a concentration of fumes
such as a stairwell, covered breezeway, etc.
1. Termination must exhaust above air inlet elevation. It is
recommended that at least 60 inches (1524mm) of vertical pipe be installed when appliance is vented directly
through a wall. This will create a natural draft, which
will help prevent the possibility of smoke or odor venting
into the home during a power outage. It will also keep
exhaust from causing a nuisance or hazard by exposing
people or shrubs to high temperatures. The safest and
preferred venting method is to extend the vent vertically
through the roof.
4. INSTALL VENT AT CLEARANCES SPECIFIED BY THE
VENT MANUFACTURER.
5. Secure exhaust venting system to the appliance with at
least 3 screws. Also secure all connector pipe joints with
at least 3 screws through each joint.
NOTE: All pipe must be welded seam pipe whenever possible. Seal pipe joints with high temperature silicone (500°F
[260°C] minimum rated only).
NOTE: If burning shelled field corn, you must use approved
venting specifically designed for corn. Follow the instructions from the venting manufacturer.
2. Distance from doors and opening windows, or gravity or
ventilation air inlets into building:
a. Not less than 48 inches (1219mm) below;
b. Not less than 48 inches (1219mm) horizontally
from;
c. Not less than 12 inches (305mm) above.
3. Distance from permanently closed windows:
a. Not less than 12 inches (305mm) below, horizontally
from or above.
WARNING
Fire Risk.
• Only LISTED venting components may be
used.
• NO OTHER vent components may be used.
Substitute or damaged vent components may
impair safe operation.
WARNING
5. Distance to combustible materials must be 24 inches
(610mm) minimum. This includes adjacent buildings,
fences, protruding parts of the structure, roof overhang,
plants and shrubs, etc.
6. Termination Cap Location (Home Electrical Service)
•
Side-to-side clearance is to be the same as minimum
clearance to vinyl inside corners.
•
Clearance of a termination cap below electrical service
shall be the same as minimum clearance to vinyl soffits.
•
Clearance of a termination cap above electrical service
will be 12 inches (305mm) minimum.
•
Location of the vent termination must not obstruct or
interfere with access to the electrical service.
7014-083E
September 1, 2008
Vent surfaces get HOT, can cause burns
if touched. Non-combustible shielding or
guards may be required
Page 12
4. Distance between bottom of termination and grade
should be 12 inches (305mm) minimum. This is conditional upon plants in the area, and nature of grade
surface. The grade surface must be a non-combustible
material (i.e., rock, dirt). The grade surface must not be
lawn. Distance between bottom of termination and public
walkway should be 84 inches (2134mm) minimum.
R
WARNING
C. Equivalent Feet of Pipe
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. Refer
to the owner’s information manual provided with this appliance. For assistance or additional information consult a
qualified installer, service agency or your dealer.
The table below can help you calculate the equivalent feet of
pipe which is a method used to determine pellet vent size. See
Figure 13.1.
Example of 3 Elbow-Rear Vent Termination Calculation
2 ft.
Pellet Venting
Component
# of
Elbows
90o Elbow or Tee
3
Feet of Multiplied
Pipe
By
45o Elbow
3 ft.
Equivalent
Feet
Equivalent Feet
Components
X
5
15
X
3
Horizontal Pipe
7
X
1
7
Vertical Pipe
2
X
0.5
1
Total Equivalent Feet
23
2 ft.
Note: This is a generic example and is not
intended to represent any specific fuel type.
2 ft.
Figure 13.1
D. Pipe Selection Chart
The chart will help you in determing proper venting
size according to the equivalent feet of pipe calcuated
above and the altitude above sea level of this installation. See Figure 13.2.
Locate the calculated equivalent feet of pipe on
the vertical left side of the chart. Move to the right
horizontally on the chart until you reach your altitude
above sea level.
30
Example 1
20
Equivalent Pipe
Length In Feet
Example 2
10
If you fall below the diagonal line, 3 or 4 inch (76 to
102mm) pipe may be used. If it is anywhere above
the diagonal line, a 4 inch (102mm) diameter pipe is
requried.
The chart reveals that a 90° elbow is 5 times as
restrictive to the flow of exhaust gases under positive
pressure as 1 foot of horizontal pipe, and a foot of
horizontal pipe is twice as restrictive as a foot of
vertical pipe.
4 in. (102mm) Diameter Pipe Only
3 in. or 4 in. (76mm or 102mm) Diameter Pipe
0
1
Figure 13.2
2
3
4
5
6
7
8
9
10
ALTITUDE IN THOUSANDS OF FEET
Example 1: If the equivalent length of pipe is 23 feet with altitude of
8,000 feet you must use 4 inch (102mm) diameter type “L” or “PL”
vent.
Example 2: If the equivalent length of pipe is 12 feet with altitude of
6,000 feet you may use 3 or 4 inch (76 to 102mm) diameter type “L”
or “PL” vent
WARNING
Fire Risk.
Do NOT pack insulation or other combustibles between firestops.
• ALWAYS maintain specified clearances around venting and firestop systems.
• Install firestops as specified.
Failure to keep insulation or other material away from vent pipe may cause fire.
Septemer 1, 2008
7014-083E
Page 13
R
5
Venting Systems
B. Direct Connect Without Outside Air
A. Direct Connect With Outside Air
NOTE: In Canada, only a full reline is
allowed per ULC S-628, ORD ULC C1482.
NOTE; Use metal plate
around exhaust vent pipe
and seal all edges with
non-flammable insulation
such as fiberglass, mineral
wool or ceramic material.
Do not use high temperature caulking materials to
seal any edge to prevent
future serviceability.
Outside Air
through
Rear Wall
Figure 14.1
Figure 14.2
WARNING
NOTE:
• Illustrations reflect typical installations and are FOR
DESIGN PURPOSES ONLY.
• Illustrations/diagrams are not drawn to scale.
• Actual installation may vary due to individual design
preference.
Fire Risk.
Inspection of Chimney:
• Masonry chimney must be in good condition.
• Meets minimum standard of NFPA 211
• Factory-built chimney must be 6 inch (152mm)
UL103 HT.
CAUTION
NOTE:
In Canada, where passage through a wall or partition of
combustible construction is desired, the installation shall
conform to CAN/CSA-B365.
Never draw outside combustion air from:
• Wall, floor or ceiling cavity
• Enclosed space such as an attic or garage
Page 14
7014-083E
September 1, 2008
R
C. Full Reline With Outside Air
NOTE: Check clearances carefully for this
type of installation to ensure adequate room
for outside air venting.
12” (305mm)
min. above
12” (305mm)
min. below
NOTE: In Canada, only a full reline is
allowed per ULC S-628, ORD ULC C1482.
CAUTION
Check building codes prior to installation.
• Installation MUST comply with local, regional,
state and national codes and regulations.
• Consult local building, fire officials or authorities
having jurisdiction about restrictions, installation inspection, and permits.
NOTE; Use metal
plate around
exhaust vent pipe
and seal all edges
with non-flammable
insulation such as
fiberglass, mineral
wool or ceramic.
Outside Air
Termination
at
Chimney Top
Do not use high
temperature caulking materials to seal
any edge to prevent
future serviceability
Exit through the
Ash Clean-Out of
Masonry Chimney
Outside Air
through
Rear Wall
Figure 15.1
Septemer 1, 2008
7014-083E
Page 15
R
6
Mobile Home
A. Mobile Home Installation
You must use a Quadra-Fire Outside Air Kit for installation in a mobile home.
1.
An outside air inlet must be provided for the combustion
air and must remain clear of leaves, debris, ice and/or
snow. It must be unrestricted while the appliance is
in use to prevent room air starvation which causes
smoke spillage. Smoke spillage can also set off smoke
alarms.
2.
The combustion air duct system must be made of
metal. It must permit zero clearance to combustible
construction and prevent material from dropping into
the inlet or into the area beneath the dwelling and
contain a rodent screen.
3.
CAUTION
Maintain structural integrity of mobile home:
• Floor, wall, ceiling and/or roof.
Do NOT cut through:
• Floor joist, wall studs or ceiling trusses.
• Any supporting material that would affect the structural
integrity.
Spark Arrestor Cap
The appliance must be secured to the mobile home
structure by bolting it to the floor (using lag bolts). Use
the same holes that secured the appliance to the shipping pallet.
4.
The appliance must be grounded with #8 solid copper
grounding wire or equivalent, terminated at each end
with an NEC approved grounding device.
5.
Refer to Clearances to Combustibles and floor protection requirements on pages 8 & 9 for listings to
combustibles and appropriate chimney systems.
6.
Use silicone to create an effective vapor barrier at
the location where the chimney or other component
penetrates to the the exterior of the structure.
7.
Follow the chimney manufacturer’s instructions when
installing the vent system for use in a mobile home.
8.
Installation shall be in accordance with the Manufacturers Home & Safety Standard (HUD) CFR 3280, Part
24.
Storm Collar
Roof Flashing
Joist Shield/Firestop
Approved Class “L” o
“PL” Pellet Vent
Figure 16.1
WARNING
Installation must comply with Manufactured Home and
Safety Standard (HUD), CFR 3280, Part 24.
WARNING
Never install in a sleeping room.
Page 16
7014-083E
September 1, 2008
R
7
Appliance Set-Up
A. Rear Shroud Installation
1. Top Vent Installations
Parts Required:
REAR SHROUD TOP
VENT PART 811-0 0
Part 811-0680, Rear Shroud Kit.
Includes: Six galvanized steel shroud pieces, two cover
plates and fastener package.
Part 811-0650, Rear Shroud Top Vent
Includes: Vent pipe and two 1/4 - 20 x 3/4 inch bolts with
nuts.
Part 811-0660, 3 inch Top Vent Adapter
4 inch Top Vent Adapter
Right Corner
Top Vent Opening
Left Corner
Part 811-0670,
orner
Left C iece
P
Filler
r
ut Rea
noc -O cess
c
A
t
n
Ve
2. Rear vent installations
Parts Required:
ent
e Air V
Outsid ccess
Pipe A
Part 811-0680, Rear Shroud Kit.
Part 811-0690, Rear Vent Kit
Includes: Rear Vent Adapter and fastener package.
Figure 17.1
Tools Required:
Electric drill, 1/8 inch drill bit, Phillips screw driver, 3/8 inch
wrench & 7/16 inch wrench, (7/16 inch socket wrench & high
temperature silicone adhesive are also required for rear vent
installations).
Filler Piece
Rear Shroud
Top Vent
Complete the following procedures, based on
your venting installation, prior to installing
the rear shroud kit. (Note: All photos depict top vent
installation).
Figure 17.2
Top Vent Installation Preparation
Figure 17.3
1. Remove the top vent adapter from the vertical exhaust
transition pipe. Figures 17.2 and 17.5.
2. Use 2 screws to attach left corner filler piece of rear
shroud to the insert hopper. Figures 17.1 and 17.2.
3. Use (2) 1/4 - 20 x 3/4 inch bolts with nuts to install rear
shroud top vent to the exhaust transition. See boxed
area in Figure 17.3. (Circled area, top vent adapter,
will be installed later).
Vertical Exhaust
Transition Pipe
Left Corner
Piece
4. Install the left shroud panel corner at 3 points, 2 screws
into back of hopper and 1 down into the filler piece).
Figure 17.4
Top Vent Adapter
Figure 17.4
Septemer 1, 2008
7014-083E
Figure 17.5
Page 17
R
Rear Vent Installation Preparation:
1.
Remove the ENTIRE exhaust blower housing by removing the 4 nuts using a 7/16 inch socket wrench. Set the
nuts aside for later use.
2.
Remove the 4 screws and remove the vertical exhaust
transition pipe exhaust blower housing.
3.
Remove any silicone sealant remaining on the blower
housing.
4.
Attach the rear vent adapter to the exhaust blower housing with 4 screws. Figure 18.2.
5.
6.
7.
8.
9.
4. Assemble the right corner and right panel pieces using 4
screws prior to attaching to insert. Figure 18.4.
5. After assembly, attach the right shroud panel/corner piece
assembly to the insert with 3 screws across the bottom and
1 on the side. Figure 18.4.
Knock-Out
Plate
Outside Air
Cover Plate
Apply a bead of high temperature silicone adhesive
around the juncture of the blower housing and rear vent
adapter, smoothing it around the joint to ensure that a
good seal is made.
Rea
Left Side
r Pa
nel
Figure 18.3
Re-install the exhaust blower housing (now with rear vent
adapter attached) with the 4 nuts previously removed in
Step 1.
Right Corner Piece
Use 2 screws to attach left corner filler piece of rear
shroud to the insert hopper. Figures 17.1 & 17.2 on
page 17.
Attach right
corner piece to
side panel first.
Install the left shroud corner with 2 screws into the hopper
body and 1 down into filler piece. Figure 18.1.
Rear Panel
Right Side
Install cover plate over top vent opening using 4
screws.
Figure 18.4
Attaching Shroud to Hopper Body:
6. Beginning at the right shroud panel drill into hopper body
through the 3 pre-drilled openings and the 2 pre-drilled
openings on the rear shroud panel. Figure 18.5. Continue
around to left shroud corner panel at the 2 pre-drilled
openings. Figure 18.6. Secure with screws to insert.
7. For Top Vent Installation:
Install 3 inch or 4 inch (76 or 102mm) top vent adapter.
See circled area in Figure 17.3 on page 17. NOTE:
This adapter may be attached to outside venting prior to
latching it on to the top vent pipe.
Left Corner
Piece
Figure 18.1
Figure 18.2
rill
oles
rill
oles
Installing Rear Shroud
Top Vent Applications: Leave knock-out plate in place.
Figure 18.3
Rear Vent Applications: Clip corners of knock-out plate,
remove and discard, prior to assembling rear shroud kit.
Rear Panel
Figure 18.5
1. Install rear panel using 4 screws along bottom and 2 screws
into the left shroud corner piece at the top. Figure 18.3.
rill
oles
2. If your installation does not include an outside air kit,
attach cover plate with 4 screws.
3. Attach left shroud panel using seven screws, 3 on top and
bottom and 1 along the side. Figure 18.3.
Page 18
7014-083E
Figure 18.6
September 1, 2008
R
C. Adjustable Hopper Options
B. Outside Air Kit Instructions
Depending on your installation, the hopper can be vertically
adjusted up to a maximum of 3-1/2 inches (89mm) and will
hold an additional 15 lbs of fuel.
Parts Included in Kit: 1 piece of 2 inch x 3 ft. flex hose,
1 hose clamp and 1 rodent screen.
Tools Needed: Phillips head screw driver; wire cutters;
hole saw or jig saw.
1. Measure distance from floor to air vent opening in appliance and mark location on wall.
To adjust hopper:
1. Using a Phillips head screw drive, remove all the screws
from the top of the hopper securing the top hopper piece
to the bottom hopper piece and insert body.
2. Use saw to cut opening in wall. Cut a 2-1/2 to 3 inches
(64-76mm) opening on inside wall and a 3 to 3-1/2 inch
(76-89mm) opening on outside of house.
2. Adjust upward a maximum of 3-1/2 inches (89mm).
3. Use hose clamp to secure flex pipe to collar assembly.
3. Mark location for new holes and drill new holes.
4. Slide trim ring over flex pipe and run pipe through wall.
4. Secure hopper pieces together using screws removed in
step one.
5. See drawing on page 7, Figure 7.3.
5. Attach hose to outside termination cap with second
hose clamp.
6. Secure termination cap to outside surface.
D. Optional Grille Installation
7. Secure trim ring to interior wall.
1. Remove grille from packaging.
CAUTION
2. Lift top up.
Never draw outside combustion air from:
• Wall, floor or ceiling cavity
• Enclosed space such as an attic or garage
3. Align the 3 holes in the insert with the holes in the grille.
4. Use a Phillips screw driver to secure in place. It will be
necessary to go through the hole in the bag support shelf
to gain access to the screw. Figure 19.3.
5. Lower the top into position.
Bag Support Shelf
Outside air
flex pipe
Attach hose clamp to
intake air collar
Figure 19.3
Figure 19.1
ri
le
Rin
ose
ose Cla
Collar
Asse
l
ose Cla
er ination
Ca Asse l
Figure 19.2
Septemer 1, 2008
7014-083E
Page 19
R
E. Adjustable Hearth Support
EXPLODED VIEW OF SCISSORS
Size: 9”d x 45”w, 2” to 10” Height Adjustment
Included in Kit: (1) trim top, (1) trim front, (2) trim sides,
double-sided tape (already installed)
SCREWS ARE CIRCLED
Tools Needed: Phillips head screw driver, sheet metal
shears, measuring tape, gloves
1. The 10 screws on each set of scissors will already be
loose when shipped. Figure 20.1.
DOUBLE-SIDED TAPE
DOUBLE-SIDED TAPE
Figure 20.1
2. Expand scissors to desired height. Tighten screws to hold
in place using Phillips head screw driver. Figure 20.2.
3. Measure front and side trims to required height to cover
scissors and mark pieces for cutting. Cut excess material from top of trim’s edge, not bottom. This edge will
be sharp; wear gloves to prevent injury to your hands.
Figure 20.3.
EXPAND SCISSORS TO DESIRED HEIGH T
4. Using sheet metal shears, cut trim along the marked
edge. The cut edge fits under lip of top trim, so it allows
for some variance in your straight edge.
5. The double-sided tape that holds front and side trims to
scissors has a powerful bonding adhesive. Adjustments
are extremely difficult once trim has adhered to tape. Do
a dry run first without removing paper from tape.
INSTALL FRONT TRIM LAST.
CORNERS OVERLAP SIDE
TRIM PIECES
CUT TOP EDGE OF TRIM,
NOT BOTTOM EDGE
Figure 20.2
6. Place cut edge of trim under top lip and into position on
scissors. Place side pieces on first and then front piece.
The front piece overlaps side pieces.
7. Once you are satisfied with the positioning, remove trim
and set aside.
8. Remove the paper from double-sided tape that is to
accept trim side. Align side and then press hard against
tape to secure side piece. Repeat for other side. Install
front trim piece last.
Decorative tile
may be installed
9. There are 3 holes in the back flange of the top to secure
it to the wall if necessary. Use the appropriate fastener
for the type of wall material, i.e., brick, sheetrock, etc.
NOTE: 3/8 inch (9.5mm) thick tile or like material can be
cut to size and fit under lip of top trim edge for a decorative touch. Figure 20.3.
Figure 20.3
WARNING
Sheet metal trim edges will be sharp.
For safety purposes wear gloves.
Injury can occur.
Page 20
7014-083E
September 1, 2008
R
F. Panel and Trim Set
Standard Size: 30 inches H x 40 inches W (762mm x 1016mm)
Large Size: 33 inches H x 50 inches W (838mm x 1270mm)
Included in Kit: 2 side panels, 1 top panel, 2 side trim, 1
top trim, 2 corner brackets and fastener package.
Tools Needed
Phillips and flat head screw drivers.
1. Unpack and lay out parts face down (flanges up) on a nonabrasive surface as shown in Figure 21.1. Install (1) 8-32
x 3/8 inch screw into bottom tab of side panel.
Figure 21.3
2. Set the large hole at bottom of side curtain over screw
installed in Figure 21.2.
3. Stand assembly on end and attach and install (1) 8-32 x 3/8
inch screw through tab in side panel and curtain. Figure
21.4. Lay face down as shown in Figure 21.5.
4. Align top panel to side panel setting clearance hole over
screw head in side panel/curtain assembly. Install (2) 8-32
x 3/8 inch screws through holes in side panel into top panel.
Figure 21.6. Complete for both sides.
Corner
Bracket
Top Trim
Top Panel
Right
Trim
Right
Panel
*Right Side
Curtain
*Left Side
Curtain
Corner
Bracket
Left
Trim
Figure 21.4
Left
Panel
Figure 21.1
NOTE: *Right and left side curtains are shipped
with the insert.
Figure 21.5
Figure 21.6
Figure 21.2
Septemer 1, 2008
7014-083E
Page 21
R
F. Panel and Trim Set (Cont’d)
5. Hold side curtains in open position and lower panel set
over insert setting lower edge of top panel in slot between
hopper lid and panel support as shown in Figure 22.1.
Place existing screw head (installed in Figure 21.2) into
locator hole in floor of insert. Figure 22.2.
6. Lift hopper lid and press down on panel top while installing
(4) 8-32 x 3/8 inch screws into holes in panel support. (If
screws have been factory installed, tighten to secure panel
to panel support.) Return hopper lid to closed position.
7. Install a corner bracket on each side trim piece. Slide
brackets into top trim from each side and secure with
flathead screwdriver. Attach trim assembly to panel set
as follows:
Figure 22.3
a. Ensure that brackets face towards the back.
b. Align trim assembly to panel set sides and slide down.
View of "L" Bracket
installed
Figure 22.4
Figure 22.1
Panel Locator Hole
Figure 22.5- Completed View
Figure 22.2
Page 22
7014-083E
September 1, 2008
R
G. Optional Brick Set Installation
WARNING
1.
Slide bottom of left rear brick in first; rotate top edge toward rear of appliance and then rotate outer edge toward
rear of appliance, until brick slides into place. Figure 23.1.
Repeat for right rear brick.
2.
Place left side brick along left side of firebox, making sure
chamfered (beveled) back edge fits snugly next to left rear
brick. Figure 23.2. Repeat with right side brick.
3.
Complete brick set, correctly installed. Figure 23.4.
Figure 23.1
Risk of Injury.
• Brick may have small wires protruding from
the back of brick.
H. Brick Clip Installation
1.
After the brick set has been installed, 2 brick clips need to
be installed on the outer edge of baffle to keep the brick
set in place. Remove the baffles from the appliance before
installing the brick clips.
2.
Using pliers, bend the brick clip slightly past 90° in the
direction shown in Figure 23.4.
3.
Position the brick clip as shown in Figure 23.4 and use pliers
to crimp around the outside edge of the baffle. Figure 23.5
shows the finished shape of the brick clip after being bent
around the outside edge of the baffle.
4.
Slide the baffles back into place making sure that the brick
clip holds the brick out toward the wall of the firebox. Push
back on the sides so they keep the rear bricks in place.
Repeat for the opposite side.
Approximately
1 inch
Outside edge
of Baffle
Top outside
corner of Baffle
Figure 23.2
Brick Clip
Figure 23.4
Installed Clip
Figure 23.5
Figure 23.3
Septemer 1, 2008
7014-083E
Page 23
R
I. Optional Log Set Placement Instructions
J. Thermostat Installation
CAUTION
1.
A 12 volt AC thermostat is required to operate this pellet
appliance. You may use the included wall mount thermostat or purchase an optional programmable thermostat
or remote control. The included thermostat is equipped
with an adjustable heat anticipator. The current rating is
.05 amps. The anticipator needs to be adjusted to the
lowest setting available.
2.
When mounting a thermostat on a wall, be sure to follow
your thermostat installation instructions carefully.
Logs are FRAGILE. Use extreme care when handling or
cleaning logs.
1.
Place the front log in first as shown in Figure 24.1
charred area surrounding firepot.
2.
Set the left and right logs onto the front log, placing
the holes in the base of the left and right logs over the
locating pins in the front log. See Figure 24.2. Ensure
that the charred ends are facing the firepot.
NOTE: Thermostat must be mounted level for accurate readings. The thermostat should be mounted on
an inside wall and not in direct line with the appliance
convection air. Remove any packaging from inside
the thermostat before using.
NOTE: If the thermostat is located too close to the
appliance, you may need to set the temperature
setting slightly higher to maintain the desired temperature in your home.
3.
LOCATING PINS
Open right side plane to access a 4 screw terminal block
located on the bottom right hand side next to the power
cord inlet. The center 2 screws are for the thermostat
wires. The outer 2 are the mounting screws for the terminal block. Figure 24.3.
CAUTION
Shock hazard.
• Do NOT remove grounding prong from plug.
• Plug directly into properly grounded 3 prong
receptacle.
• Route cord away from appliance.
• Do NOT route cord under or in front of appliance.
Figure 24.1
Charred Areas in the Bac
Top Log
Right
Top Log, Left
er inal lock
Center Scre s for
er ostat ires
Front Log
Figure 24.2
NOTE:
Due to the abrasive nature of a pellet appliance fire, the
logs are not covered under warranty. Any placement variation other than shown here can cause excessive heat
and shall void the appliance warranty.
Page 24
Po er Outlet
Figure 24.3
7014-083E
September 1, 2008
R
8
Operating Instructions
A. Fuel Size And Material
B. General Operating Information
1. Wood Pellets
1. Thermostat Calls For Heat
Fuel pellets are made from sawdust or wood by-products. If the
source material is hardwood, they can have a higher mineral
content, creating more ash. Fuels containing bark will also
have higher ash content. Minerals and other non-combustible
materials such as sand will turn into a hard, glass-like substance
called a clinker when heated to the extreme temperatures
our firepot reaches. This is what forms clinkers in the bottom
of the firepot. Trees from different areas will vary in mineral
content. That is why some fuels produce more clinkers than
others. Pellets are manufactured in either 1/4 inch or 5/16 inch
(6-8mm) diameter and should be no more than 1-1/2 inches
(38mm) in length. Pellet lengths may even vary by lot from the
same manufacturer which is why the feed rate may need to be
adjusted occasionally. If you burn pellets longer than 1-1/2
inches (38mm) you may have an inconsistent fuel feed rate
and/or missed ignitions.
The appliance is like most modern furnaces; when the thermostat
calls for heat, your appliance will automatically light and deliver
heat. When the room is up to temperature and the thermostat
is satisfied, the red call light will shut off and the appliance will
shut down. Figure 25.1.
Pellet fuel quality can greatly fluctuate. We recommend using
premium grade fuel with ash content less than 1%. Even in some
fuel labeled “premium” ash content can vary from bag to bag
and possibly exceed 1%. High ash fuel, or lack of maintenance,
can cause the firepot to fill up and thus create a potential for
smoking, sooting and possible hopper fires.
2. Heat Output Controls
This appliance is equipped with a heat output control switch that
has three settings or burn rates; low, medium and high. The
appliance will turn on and off as the thermostat demands. When
the thermostat calls for heat, the appliance will always start up
on High. After burning approximately 4 minutes, the appliance
will then burn at the rate at which it was originally set. If the
appliance is set at one of the lower settings, it will run quieter
but takes longer to heat up an area than if it were set at a higher
burn rate. Regardless of the burn rate, when the area is warm
enough to satisfy the thermostat, the appliance will shut off.
Control o
Always burn dry fuel. Burning fuel with high moisture content
takes heat from the fuel and tends to cool the appliance,
robbing heat from your home. Damp pellet fuel can clog the
feed system.
We recommend that you buy fuel in multi-ton lots whenever
possible. Buying large quantities of fuel at once will greatly
reduce the number of times the feed adjustments will need to
be made. However, we do recommend trying various brands
before purchasing multi-ton lots to ensure your satisfaction.
eat Out ut S itc
Reset utton
Red Call Li
Blue
Blin ing
Light
t
use
Red / reen
Light
Figure 25.1
ARNING
Fire Risk.
WARNING
High ash fuels, or lack of maintenance,
can cause the repot to ll with ash
and clinker. If the repot lls to the top,
immediately shut down the unit and clean.
Fire Risk.
Keep combustible materials, gasoline and other
flammable vapors and liquids clear of appliance.
• Do NOT store flammable materials in the appliance’s
vicinity.
Failure to do so could result in smoking,
sooting and possible hopper res.
2. Shelled Field Corn
Shelled field corn can be an efficient and economical fuel. We
recommend using a 50-50 blend of corn and wood pellets. The
only change in operation; 1) the feed rate may require a slight
adjustment and 2) firepot will require more frequent cleanings.
The BTU output varies slightly compared to pellets, depending
on the quality of the corn used. In cases where it is acceptable
for the appliance to run full time, 100% corn will work after the
fire has been started using wood pellets.
Septemer 1, 2008
• Do NOT use gasoline, lantern fuel, kerosene, charcoal
lighter fluid or similar liquids to start or “freshen up” a fire in
this heater.
• Keep all such liquids well away from the heater while it is in
use.
• Combustible materials may ignite.
7014-083E
Page 25
R
C. Before Your First Fire
E. Fire Characteristics
1. First, make sure your appliance has been properly
installed and that all safety requirements have been met.
Pay particular attention to the fire protection, venting and
thermostat installation instructions.
3. Check the position of the thermocouple, located above
the firepot, and make sure that it protrudes approximately
3/4 inch (19mm) into the firepot.
A properly adjusted fire with the heat output control switch set
on “HIGH” has a short active flame pattern that extends out
of the firepot approximately 4 to 6 inches (102-105mm). If
the fire has tall flames with black tails and seems somewhat
lazy, the feed rate will need to be reduced. If the fire is not 4
inches to 6 inches (102-105mm) tall, increase the feed rate.
A medium and low setting will give a shorter flame. The flame
will rise and fall somewhat. This is normal.
4. Close the front door.
F. Feed Rate Adjustment Instructions
2. Double check that the ash pan and firebox are empty!
The feed adjustment control rod is factory set, and should
be adequate for most fuels. The set screw is located at the
bottom of the hopper and set loose at the factory so the fuel
adjustment control rod will slide by only loosening the wing
nut. Do not re-tighten bottom set screw.
CAUTION
Tip of thermocouple must be in contact with the inside
end of the thermocouple cover.
Missed ignitions can occur.
D. Starting Your First Fire
1. A thermostat is required for proper operation of this
appliance, except for corn. At this time, fill the hopper
with pellets, set the thermostat to its lowest setting. Plug
the power cord into nearby outlet.
2. The exhaust blower will stay on for approximately 10
minutes even though the thermostat is not calling for
heat. This is normal.
3. Locate the heat output control switch on the right side
behind the right side panel. Set to the HIGH setting and
then adjust the thermostat to its highest setting. The
red call light will be on which is located on the right side
behind the right side panel. This indicates the thermostat
is calling for heat. See Figure 25.1 on page 25.
4. The fuel feed system and the igniter should now be on.
5. For your first fire it will be necessary to press the reset
button approximately 2 minutes after start-up and again
at 4 minutes. This will fill the feed system and allow the
appliance to begin dropping pellets. Continue pushing
the reset button until you detect that pellets are being
delivered into the firepot. The appliance will continue to
run as long as the thermostat is calling for heat.
6. Once the appliance has ignited, let the it burn for
approximately 15 minutes, then set the thermostat to the
desired room temperature. Adjust the heat output control
switch to the desired setting.
However, if the flame height is too high or too low, you will
need to adjust the feed rate. Wait until the appliance has been
burning for 15 minutes before making your adjustments and
allow 15 minutes for feed adjustment to take effect.
1. Open the hopper lid and locate the fuel adjustment control
rod.
2. Loosen the wing nut on the rod.
3. Adjust the fuel adjustment control rod towards the "+"
symbol to increase the feed rate and flame height or
towards the "-" symbol, to decrease the feed rate and
G. Ignition Cycles
1. During each ignition cycle, it is normal to see some smoke
in the firebox. The smoke will stop once the fire starts.
2. The convection blower will automatically turn on after your
appliance has reached the set temperature. This blower
transfers heat from your appliance into the room, and will
continue to run after the thermostat has stopped calling
for heat until the appliance has cooled down.
3. Occasionally the appliance may run out of fuel and shut
itself down. When this happens, the red call light will be
on. To restart it, fill the hopper and press the reset button.
When you press the reset button the red call light will go
out. Release the button and the light will come back on.
You should see a fire shortly. If not, follow the instructions
“Starting Your First Fire”.on this page.
CAUTION
Odors and vapors released during initial operation.
• Curing of high temperature paint.
• Open windows for air circulation.
Odors may be irritating to sensitive individuals.
Page 26
7014-083E
September 1, 2008
R
WARNING
Fire Risk
Do NOT operate appliance:
• With appliance door open.
• Firepot floor open.
• Cleaning slide plates open.
Do NOT store fuel:
• Closer than required clearances to combustibles to appliance
• Within space required for loading or ash
removal.
Back side of Firepot
Firepot floor left open
Figure 27.1 - DO NOT LEAVE FIREPOT FLOOR OPEN
H. Frequently Asked Questions
ISSUES
SOLUTIONS
1. Metallic noise.
1. Noise is caused by metal expanding and contracting as
it heats up and cools down, similar to the sound produced by a furnace or heating duct. This noise does not
affect the operation or longevity of your appliance.
2.
Ash buildup on glass.
2. This is normal. Clean the glass.
3.
Glass has turned dirty.
3. Excessive build up of ash. The lower burn settings will
produce more ash, the higher burn settings produce
less. The more it burns on low the more frequent cleaning of the glass is required.
4.
Fire has tall flames with black tails and is lazy.
4. The feed rate needs to be reduced or the firepot needs
cleaning. Heat exchanger or exhaust blower needs
cleaning.
5.
Smokey start-up or puffs of smoke from the airwash. 5. Either the firepot is dirty or there is too much fuel at
start-up and not enough air. Close down feed rate 1/4
inch (6mm) at a time until this no longer happens.
6.
Large flame at start-up.
Septemer 1, 2008
6. This is normal. Flame will settle down once the fire is
established.
7014-083E
Page 27
R
9
With proper installation, operation, and maintenance your appliance will provide years
of trouble-free service. If you do experience a problem, this troubleshooting guide
will assist a qualified service person in the diagnosis of a problem and the corrective
action to be taken. This troubleshooting guide can only be used by a qualified service
technician.
Troubleshooting
Possible Cause
Symptom
Plug in appliance - No
response.
Call light on. No fire.
No fuel in firepot.
Partially burned fuel in
firepot.
Corrective Action
No current to outlet.
Check circuit breaker at service panel.
.7 amp fuse defective.
Replace fuse.
#3 snap disc tripped or defective.
Reset or replace snap disc.
Control box defective.
Replace control box.
Out of fuel.
Check hopper. Fill with fuel.
#2 snap disc may be defective.
Replace snap disc.
Vacuum switch not closing, no vacuum.
Check exhaust blower is plugged in and
operating.
Check vacuum switch is plugged in.
Check vacuum hose is in good condition,
clear and connected at both ends.
Check thermocouple is in good condition
and plugged in properly.
Make sure venting system is clean.
Make sure front door is closed.
Firepot clean-out plate not closed.
Check that firepot clean-out plate is fully
closed.
Firepot is dirty (missed ignition).
Clean firepot. Make sure there is no clinker
in the firepot.
Clinkers may have to be broken up with
firepot scraper tool or other means.
Unburned pellets in
firepot.
closed.
Firepot is dirty.
Clean firepot. Make sure there is not a
clinker in the firepot. Clinkers may have to
be pushed out of firepot with firepot scraper
tool or other means.
Ignition hole blocked.
Scrape with solid piece of wire.
Remove ash pan to see if igniter is glowing
red on start-up.
Check igniter wires for good connection.
Replace igniter using 1/4 inch male /female
spade connectors.
Igniter not working.
Slow or smoky start-up.
Page 28
Check that firepot clean-out is fully closed.
Firepot is dirty.
Clean firepot. Make sure there is not a
clinker in the firepot. Clinkers may have to
pushed out of firepot with firepot scraper
tool or other means.
Excessive amount of fuel at start-up.
Reduce feed rate using feed rate adjustment control rod located inside hopper.
7014-083E
September 1, 2008
R
Troubleshooting (Cont’d)
Symptom
Possible Cause
Corrective Action
Slow or smoky start-up
(Cont’d)
Dirty exhaust and/or venting system.
Check for ash build up in appliance,
including behind rear panels, firebox, heat
exchanger, exhaust blower and venting.
Feed system fails to
start.
Out of fuel.
Check hopper, fill with fuel.
#2 snap disc may be defective.
Replace snap disc. Firebox door must be
closed securely.
Vacuum switch not closing. No vacuum.
Check exhaust blower is plugged in and
operating.
Check vacuum switch is plugged in.
Check vacuum hose is in good condition,
clear and connected at both ends.
Check thermocouple is in good condition
and plugged in properly.
Make sure venting system is clean.
NOTE: High winds blowing into the venting system can pressurize the firebox
causing loss of vacuum.
Feed system jammed or blocked.
Empty hopper of fuel. Use a wet/dry
vacuum cleaner to remove remaining fuel,
from hopper, including feed tube.
Check feed chute for obstructions.
Loosen 2 screws and jiggle feed assembly.
Feed spring not turning with feed motor.
Check that set screw is tight on feed
spring shaft at end of feed motor.
Feed motor defective or not plugged in.
Check connections on feed motor, replace
if defective.
Thermostat not set to a high enough temperature.
Adjust thermostat above room temperature.
Snap Disc #3 tripped.
Reset snap disc.
No power.
Connect to power.
Fuse blown.
Replace fuse.
No call light. Appliance
does not begin start
sequence.
Connections at thermostat and/or appliance not Check connections at thermostat and
making proper contact.
appliance.
Defective thermostat or thermostat wiring.
Replace thermostat or wiring.
NOTE: To test thermostat and wiring, use
a jumper wire at the thermostat block on
the appliance to by-pass thermostat and
wiring.
Appliance fails to shut
off.
Septemer 1, 2008
Call light on.
Turn thermostat off.
If call light does not go out, disconnect
thermostat wires from appliance. If call
light does go out, thermostat or wires are
defective.
7014-083E
Page 29
R
Troubleshooting (Cont’d)
Symptom
Convection blower fails to
start.
Exhaust blower fails to
start or does not shut off.
Large, lazy flame, orange
color. Black ash on glass.
Possible Cause
No call light.
Defective control box.
#1 snap disc defective.
Replace snap disc.
Blower not plugged in.
Check that blower is plugged into wire harness.
Blower is defective.
Replace blower.
Control box is defective.
Blower not plugged in.
Check that blower is plugged into wire harness.
Blower is clogged with ash.
Clean exhaust system.
Blower is defective.
Replace blower.
Control box is defective.
Dirty appliance.
Poor fuel quality, high ash content.
Clean appliance, including firepot, heat
exchangers and venting system. Remove
stainless steel baffle from firebox to clean
ash from on top of baffle. Clean behind rear
brick panels. Change fuel brand to premium.
Firepot clean-out plate not completely
closed.
Nuisance shutdowns.
Appliance calls for heat.
Call light illuminates.
Exhaust blower starts.
No feed or igniter.
Page 30
Corrective Action
closed.
Excessive amount of fuel.
Reduce feed rate using feed rate adjustment
control rod located inside hopper.
Low flame.
Increase feed by opening feed rate adjustment control rod located inside hopper.
Sawdust buildup in hopper.
Clean hopper, see page 33.
Feed motor is reversing.
Check for good connections between feed
motor and wire harness.
Defective thermocouple.
Replace thermocouple.
Defective control box.
Firepot more than 1/2 full
See page 35 for detailed instructions for
“High Ash Fuel Content Maintenance”.
Thermocouple is defective or not properly
plugged in.
Check connections on thermocouple or
replace if defective.
A flashing yellow light on the control box
indicates a problem with the thermocouple.
Defective control box
7014-083E
September 1, 2008
R
10
Maintaining & Servicing Your Appliance
C. General Maintenance
A. Proper Shutdown Procedure
1. Types of Fuel
CAUTION
Depending on the type of fuel you are burning will dictate
how often you have to clean your firepot.
Shock and Smoke Hazard
If the fuel you are burning has a high dirt or ash content
or you are burning shelled field corn, it may be necessary
to clean the firepot more than once a day.
• Turn down thermostat, let appliance completely
cool and exhaust blower must be off. Now you
can unplug appliance before servicing.
• Smoke spillage into room can occur if appliance
is not cool before unplugging.
• Risk of shock if appliance not unplugged before
servicing appliance.
Dirty fuel will cause clinkers to form in the firepot. A clinker
is formed when dirt, ash or a non-burnable substance is
heated to 2000°F (1093°C) and becomes glass-like. See
“D” page 35 in this section for more details on fuels with
high ash content.
.
Clinker
Figure 31.1 - Clinker
B. Quick Reference Maintenance Chart
Cleaning or Inspection
Frequency
Daily Weekly Monthly
Yearly
Ash Pan
Every 5 bags of fuel
OR
X
Ash Removal from Firebox
More frequently depending on
the fuel type or ash build-up
OR
X
Beneath Heat Exchanger
Every 1 ton of fuel
OR
Blower, Combustion (Exhaust)
the fuel type
OR
X
Blower, Convection
the fuel type
OR
X
Door Latch Inspection
Prior to heating season
OR
Exhaust Path
ash build-up
OR
Firebox - Prepare for Non-Burn Season
At end of heating season
OR
Firepot - Burning pellets
Every 3 bags
OR
X
Firepot - Burning Corn
Every 1 bag
OR
X
Glass
When clear view of firepot
becomes obscure
OR
Heat Exchanger & Drop Tube
Every 1 ton of fuel
OR
X
Hopper
Every 1 ton of fuel or when
changing fuel types
OR
X
Venting System
the fuel type
OR
Septemer 1, 2008
7014-083E
X
X
X
X
X
X
Page 31
R
2. Cleaning Firepot with Cleaning Rod & Firepot
Clean-Out Tool
•
•
4. Cleaning Ash Pan
•
•
Frequency: Daily or more often as needed
By: Homeowner
Frequency: Weekly or every 5 bags of fuel
By: Homeowner
Locate the ash pan underneath the firepot and using a
slight pull up and out remove the ash pan. Empty into
a non-combustible container and re-install ash pan.
See Disposal of Ashes.
a. Be sure the appliance is allowed to cool, has been
unplugged and the exhaust blower is off. If you are
just cleaning the firepot, there is no need to unplug the
appliance.
b. Pull firepot cleaning rod OUT and IN a couple of times
to help shake debris loose. If rod is hard to pull, it may
be necessary to use your firepot clean-out tool to chip
away material that has built up on the bottom plate of
the firepot and to push out any clinkers. Larger clinkers
may have to be removed from the top of the firepot.
Corn clinkers can be especially difficult to break up.
5. Disposal of Ashes
•
•
Frequency: As needed
By: Homeowner
Ashes should be placed in a metal container with a
tight-fitting lid. The closed container of ashes should
be placed on a non-combustible floor or on the ground,
well away from all combustible materials, pending final
disposal.
c. The firepot floor plate must be fully closed when
finished. See Figure 27.1 on page 27.
If the ashes are disposed of by burial in soil or otherwise
locally dispersed, they should be retained in the
closed container until all cinders have been thoroughly
cooled.
WARNING
Fire Risk.
WARNING
• NEVER pull firepot cleaning rods or cleaning
slide plates when appliance is operating. Hot
pellets may fall into ashpan and may start a
fire or have mis-starts due to lack of vacuum.
Heat exchanger cleaning rods may be warm
to the touch. For safety purposes wear
gloves.
3. Ash Removal from Firebox
•
•
Do not pull heat exchanger cleaning rods
while appliance is operating.
Frequency: Weekly or more frequently depending on
ash build-up.
By: Homeowner
a. Allow the appliance to completely cool down. There
must not be any hot ashes in the firebox during
cleaning. Turn the thermostat on and then immediately
off to start the exhaust blower on its cycle time. It will
pull fly ash out the exhaust instead of into the room.
b. Frequent cleaning of the ash in the firebox will help
slow down the build-up of ash in the exhaust blower
and vent system.
c. Open door. Remove ash with an ash vacuum or whisk
broom and small dust pan.
d. This ash is deposited in the same ash pan as the
firepot debris. The ash pan should be emptied every
time you clean the firebox. Remember to place the ash
and debris into a metal or non-combustible container.
See Disposal of Ashes.
WARNING
Disposal of Ashes
• Ashes should be placed in metal container
with tight fitting lid.
• Ashes should be retained in closed container
until all cinders have thoroughly cooled.
Page 32
Push cleaning rods IN when done, DO NOT
leave cleaning rods OUT. Injury can occur.
6. Cleaning Heat Exchanger Chambers & Drop Tube
•
•
Frequency: Weekly or every 1 ton of fuel
By: Homeowner
The amount of ash buildup in the firepot will be a good
guide to determine how often you should clean the heat
exchangers.
a. Allow the appliance to completely cool down before
pulling the cleaning rods. Turn the thermostat on and
then immediately off to start the exhaust blower on its
cycle time. It will pull fly ash out the exhaust instead
of into the room.
b. To access the cleaning rods lift the hopper lid. Both
black bent handle pull rods are located close to the
face of the appliance to the left and right side.
c. To clean, pull the rods straight out until it stops,
approximately 20 inches (508mm). Slide the rods
OUT and IN a couple of times.
7014-083E
September 1, 2008
R
7. Cleaning Beneath Heat Exchanger
•
•
10. Door Latch Inspection
Frequency: Monthly or after burning 1 ton of fuel
By: Homeowner
•
•
unplugged and the exhaust blower is off
.
b. A more thorough cleaning is needed to remove the
excess ash that is left behind from the use of the
cleaning rods for the heat exchanger tubes.
b. To adjust, open the latch and pivot the holding rod out.
Loosen the jam nut on the rod.
c. With a Phillips head screw driver, turn the rod clockwise
to tighten. The latch handle should snap securely in
place when adjusted properly.
c. The ash will be resting on the back of the baffles. This
will require removing the baffles. Please refer to page
37 for instructions on removing the baffles.
d. After adjusting the latch, be sure to tighten the jam nut
on the rod to hold the adjustment.
8. Cleaning Exhaust Path
•
•
Frequency: Yearly or more frequently depending on
ash build-up.
By: Homeowner
11. Door Gasket Inspection
•
•
b. To inspect the door rope (gasket), open the door and
see that the door rope extends approximately 1/8 inch
(3mm) to 3/16 inch (9.5mm) from the door rope channel.
c. Reach in and unlatch the trap door that is connected
to the rear of exhaust blower.
d. Use a small vacuum hose attachment to clean area.
c. It should show signs of compaction all the way around
the door where the rope contacts the face of the appliance. Confirm there are no air leaks.
e. Re-latch and close trap door.
NOTE: There are heavy duty vacuum cleaners specifically
designed for solid fuel appliance cleaning.
9. Cleaning the Glass
•
Frequency: When clear view of the firepot becomes
obscure.
By: Homeowner
Frequency: Prior to heating season
By: Homeowner
b. Open the hinged access door on the left of the
insert.
•
Frequency: Prior to heating season
By: Homeowner
12. Cleaning the Hopper
•
•
Frequency: Monthly or after burning 1 ton of fuel
By: Homeowner
After burning approximately 1 ton of fuel or changing
fuels you will need to clean the hopper to prevent sawdust build-up.
unplugged and the exhaust blower is off.
A combination of sawdust and pellets on the auger
reduces the amount of fuel supply to the firepot. This
can result in nuisance shutdowns and mis-starts.
b. Use a damp paper towel or any nonabrasive glass
cleaner. Wipe off with dry towel.
CAUTION
Handle glass assembly with care.
b
Empty the hopper of any remaining pellets.
c.
Vacuum the hopper and feed tube.
When cleaning glass:
• Avoid striking, scratching or slamming
glass.
• Do NOT clean glass when it is hot.
• Do NOT use abrasive cleaners.
13. Cleaning Exhaust Blower - Requires No Lubrication
•
•
•
Frequency: Yearly or as needed
By: Quality Service Technician/Homeowner
Task:: Contact your local dealer.
• Use a hard water deposit glass cleaner on white film.
• Refer to maintenance instructions.
14. Cleaning Convection Blower - Requires No
Lubrication
•
•
•
Septemer 1, 2008
Frequency: Yearly or as needed
By: Qualified Service Technician
Task: Contact your local dealer.
7014-083E
Page 33
R
15. Soot and Fly Ash: Formation & Need for Removal
in Exhaust Venting System.
•
•
Frequency: Yearly or more frequently depending on
ash build-up.
By: Qualified Service Technician/Homeowner
Be sure the appliance is allowed to cool, has been unplugged
and the exhaust blower is off.
The products of combustion will contain small particles of fly
ash. The fly ash will collect in the exhaust venting system
and restrict the flow of the flue gases.
At start-up if there is incomplete combustion, or if there is a
shutdown or incorrect operation of the appliance it will lead
to some soot formation. This will collect in the exhaust venting system.
The venting system may need to be cleaned at least once a
year or more often depending upon the quality of your fuel
or if there is a lot of horizontal pipe sections. Ash will build
up more quickly in the horizontal sections.
16. Preparing Firebox for Non-Burn Season
•
•
Frequency: Yearly
By: Homeowner
b. Remove all ash from the firebox and vacuum thoroughly.
c. Paint all exposed steel, including cast-iron.
•
Use the Touch-Up paint supplied with the appliance;
or,
•
Purchase paint from your local dealer.
•
Must use a high-temperature paint made specificially for heating appliances.
Page 34
7014-083E
September 1, 2008
R
D. High Ash Fuel Content Maintenance
•
•
Frequency: When the ash build-up exceeds more
than half way up the firepot.
By: Homeowner
Pellets Back Up
In Feed Tube
Firepot Overfills
Poor quality pellet fuel, or lack of maintenance, can create
conditions that make the firepot fill quickly with ashes and
clinkers.
This condition makes the appliance susceptible to overfilling the firepot with pellets which may result in smoking,
sooting and possible hopper fires. Figure 35.1 shows an
example where the firepot overfills, pellets back up into the
feed tube and ash has accumulated in the firebox.
As
uild
in ire o
Figure 35.1
An inefficient and non-economical method of burning of
fuel caused by poor quality pellet fuel is shown in Figure
35.2.
ncorrect
The correct flame size when good quality, premium pellet
fuel is burned is shown in Figure 35.3.
If the ash buildup exceeds the half way point in the firepot
IMMEDIATE ATTENTION AND CLEANING IS REQUIRED.
ARNING
all La
ire Risk
i as fuels or lack of aintenance
can cause t e re ot to ll it as
and clinker f t e re ot lls to t e to
i
ediatel s ut do n t e unit and clean
la e Oran e in Color
Figure 35.2
ailure to do so could result in s okin
sootin and ossi le o er res
Correct
Correct la e Si e
ello
ite in Color
Figure 35.3
Septemer 1, 2008
7014-083E
Page 35
R
E. Glass Replacement
oor Latc
WARNING
o
otto
ra e
• Glass is 5mm thick high temperature heatresistant ceramic glass.
• DO NOT REPLACE with any other material.
Center Posts
• Alternate material may shatter and cause
injury
• Remove door from appliance and place face down
on a protected surface to avoid scratching the door.
Side
ra e
lass
• Remove all door rope.
1. Replacing Center Glass
NOTE: DO NOT LET Air Wash Spacers fall down from
top frame when removing and replacing center
glass.
Figure 36.1
Re ove oor Latc irst
and t en Side ra e
b. Using a nut driver remove the (5) bottom nuts and
remove the bottom glass frame. Figure 36.2.
c. Slightly bend up and out of the way the 2 center posts
and slide the glass out the bottom.
oor ra e
s o n it no
lass or lass
ra es
d. Slide new glass in, reposition the 2 center posts and
re-install bottom glass frame.
e. Re-rope the door.
2. Replacing Side Glass
NOTE: When removing the side glass with the door
latch, you must remove the door latch first
before removing the side frame. Use a powered Phillips head screw driver to remove the
4 screws.
Re ove
otto
ra e
Figure 36.2
b. Remove side glass frame.
WARNING
c. Loosen the top and bottom frame and slightly bend
up and out of the way.
d. Slide glass out the side and slide new glass in.
e. Re-install the side glass frame and tighten the top
and bottom frames.
f. Re-install the door latch, if applicable, and re-rope
the door.
Page 36
nuts fro
Handle glass with care.
• Inspect the gasket to ensure it is
undamaged.
• Do NOT strike, slam or scratch glass.
• Do NOT operate appliance with glass
assembly removed.
• Do NOT operate with glass cracked, broken or scratched.
7014-083E
September 1, 2008
R
F. Igniter Replacement
G. Baffle Removal
b. Open glass door.
c. Grasp the bottom of the baffles and pull up to dislodge from hook attachment.
d. Use a standard screw driver to unlatch the covers
beneath the baffles of each side.
e. Re-install in reverse order.
niter racket
u
Scre
niter
Figure 37.1
unplugged and the exhaust blower is off. Remove the
ash pan.
b. The wire leads to the igniter are connected to the wire
harness with 1/4 inch male / female spade connectors.
These wires will pull forward approximately 4 to 5
inches (102mm to 127mm). Disconnect the spade
connections and remove the igniter from the chamber.
Loosen the thumb screw and slide igniter out.
c. Install new igniter into the chamber and tighten the
thumb screw. Re-connect the wires to the 2 leads with
the spade connectors.
d. Push excess wire leads to take-up the 4 to 5 inches
(102mm to 107mm) previously pulled out. This will
keep the wires out of the way of the ash pan. Double
check that the igniter wires are clear of any movement,
i.e. ash pan, firepot cleaning rod, etc.
f. Re-install the ash pan and re-connect the power.
Septemer 1, 2008
7014-083E
Page 37
R
11
Reference Materials
A. Component Function
1. Control Box
a. The control box is located on right side of appliance,
behind the right side panel.
b. There is a light located inside of the control box. The
internal light will turn green when the appliance has
reached a temperature of 200οF (93°C) in the firepot.
and will turn red when it reaches 600oF (315°C).
When describing the location of a component
part it is always AS YOU FACE THE FRONT
OF THE APPLIANCE.
7. Heat Exchangers
The heat exchangers transfer heat from the exhaust system
into convection air. There are 2 clean out rods located under
the heat exchangers.
8. Heat Output Switch
c. There is also an internal blue light located in the upper
left corner of the control box. When you plug in the
appliance the blue light will automatically start blinking
1 blink every 10 seconds for 60 seconds and then will
stop.
The heat output switch is located on the right side of firebox,
behind right side panel. The function of the heat output
switch is to regulate the burn rates; low, medium and high
settings.
NOTE:
The igniter is mounted on the base of the firepot. Combustion
air travels over the red hot igniter creating super heated air
that ignites the pellets.
Do NOT open the control box. This will void the
warranty. If you need to plug in or remove the control
box you must first unplug the appliance.
2. Convection Blower
The convection blower is mounted at the bottom rear of the
appliance. There are 2 impellers, one on each side of the
motor. The convection blower pushes heated air through the
heat exchange system into the room.
3. Combustion (Exhaust) Blower
The combustion blower is mounted on the left side of the
appliance behind the left side panel. It is accessible either
when the insert is pulled out onto the hearth or from both
hinged side openings. The blower is designed to pull the
exhaust from the appliance and push it out through the
venting system.
4. Feed System
The feed system is located behind the firebox and can be
removed as an entire assembly. The assembly includes
the feed motor, mounting bracket, bearing and feed spring
(auger). The hollow feed spring (auger) pulls pellets up the
feed tube from the hopper area and drops them down the
feed chute into the firepot.
5. Firepot
The firepot is made of high quality ductile iron and has a
cleaning pull-out rod. The floor of the firepot opens for
cleaning when you pull out the rod. Be sure that the floor
returns to a completely closed position or your appliance
will not operate properly.
6. Fuse
The fuse is located on the right side of the appliance behind
the side panel. The fuse will blow should a short occur and
shut off power to the appliance.
Page 38
9.
Igniter
10. Junction Box And Wiring Harness
The junction box is located on the right side of the appliance,
behind the right front access panel. The junction box and
wiring harness are replaced as one component.
11. Power Supply
The power outlet is located on the right side of the appliance.
Check the wall receptacle for 120 volt, 60 Hz (standard
current). Make sure the outlet is grounded and has the correct
polarity. A good surge protector is recommended. When
operating with a generator you need at least 600 watts of
power, or with an inverter at least 800 watts of power, available
for the appliance during the start cycle.
12. Red Call Light
The red call light is on the right side behind the right side
panel. The function of the red call light is to indicate that the
thermostat is calling for heat.
13. Reset Button
The reset button is located on the right side of firebox
behind right side panel. The function of the reset button is
to momentarily open the thermostat circuit, which restarts
the system.
14. Thermocouple
The thermocouple is located on top of the firepot inside
the thermocouple cover (ceramic protection tube). The
thermocouple sends a millivolt signal to the control box
indicating the preset temperatures of the green and red lights
have been obtained.
15. Thermostat
The appliance is designed to run on a 12 volt AC thermostat.
The heat anticipator, if present, should be set on the lowest
setting available.
7014-083E
September 1, 2008
R
16. Snap Disc #1 (Convection Blower) 125°F
19. Vacuum Switch
Snap disc #1 is located on the right side of the firebox. There
are 2 purple wires connected to it. This snap disc turns the
convection blower on and off as needed. Power is always
present at snap disc #1.
The vacuum switch is located at the rear of the appliance.
This switch turns the feed system on when vacuum is present
in the firebox. The vacuum switch is a safety device to shut
off the feed motor if the exhaust or the heat exchanger
system is dirty or plugged or if the firebox door is open.
17. Snap Disc #2 (Fuel Delivery Interrupt) 200°F
Snap disc #2 is located on the back side of the feed drop
tube. There is 1 orange wire and 1 black wire connected to
it. This snap disc will turn off the feed system, which will turn
off the appliance if an overfire condition should occur or if the
convection blower should fail to operate. If this occurs the
snap disc with automatically reset itself.
20. Wiring Harness
See Figure 39.1 below
18. Snap Disc #3 (Burn Back Protector) 250°F
Snap disc #3 is mounted on the right side of the auger tube
just below feed motor and has a reset button. To access
it remove the right side panel. If the fire tries to burn back
into the feed system or push exhaust up the feed tube, this
snap disc will shut the entire system off. This disc must be
manually reset.
T-STAT CONN (YEL)
T-STAT CONN
4
5
6
1
2
3
ACCY
JUMPER
BURN R ATE
SNAP DISC #2 (YEL)
BLUE
SNAP DISC #2 (YEL)
PURPLE
SNAP DISC #3 (GRAY)
P.B.
ORANGE
LIGHT
SNAP DISC #1 (PUR)
WHITE
AUG.
CAP.
BLACK
R
ED
AUGER MOTOR (RED/WHT)
FUSE
CONV. BLOWER
BLK
YELLOW
M
GRAY
ORANGE
BLK
SNAP DISC #1 (PUR)
POWER IN (BLK)
M
NEUTRAL AUGER (WHT)
NEUTRAL CONV (WHT)
RED
YELLOW
T.C .
NEUTRAL IN (WHT)
BLUE
WHITE
ORANGE
BLACK
PURPLE
RED
BLK
VAC.
COMB BLOWER (BLU) SWITCH
BLUE
GRAY
PURPLE
RED
YELLOW
YELLOW
YELLOW
WHITE
LK
BLK
HI-TEMP
HI-TEMP
B
M
AUGER MOTOR (BLK)
NEUTRAL COMB (WHT)
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
NEUTRAL IGN (HT)
T/C
IGNITER (HT)
Figure 39.1
Septemer 1, 2008
7014-083E
Page 39
R
B. Component Locations
Terminal Block
Center 2 Screws for
Thermostat Wires
Control Box
Heat Output
Switch
Reset Button
Red Call Light
Fuse
Blue
Blinking
Light
Red/ Green
Light
Power Outlet
Figure 40.1
Exhaust
Transition
Assembly
Convection
Blower
Exhaust
Blower
Figure 40.2
Page 40
7014-083E
September 1, 2008
R
C. Exploded Views
Nbr
4
not sellable
2
Glass Frame Side
not sellable
3
Glass Frame Spacer
not sellable
4
Glass Frame, Top &
Bottom
not sellable
1
5
Hinge, Female
450-2910
11
Door Frame
not sellable
13
12
Glass Assembly, Center
510-5400
13
Glass Assembly, Sides
510-5410
14
Door Latch Bracket
410-4912
14
2
11
Part Number
Glass Frame Post
3
5
Description
1
12
Glass Size Center: 13-7/8” wide x 11” high
Glass Size Sides:
5-1/8” wide x 11” high
Figure 41.1 - Door, Face, Glass, & Latch Assembly
Nbr
36
8
39
41
40
42
Description
Part Number
7
Thumb Screw
7000-223/24
8
Thermocouple
812-0210
36
Thermocouple Cover
812-1322
39
Thermocouple Holder
812-3171
40
Firepot Pull Rod (Linkage) 812-4140
41
Firepot, EZ Clean
812-3351
42
Igniter Bracket
not sellable
43
Igniter (Heating Element)
SRV7000-462
7
43
Figure 41.2 - Firepot, Igniter & Thermocouple
Septemer 1, 2008
7014-083E
Page 41
R
27
26
28
25
29
32
33
30
31
23
24
22
34
38
36
35
37
19
39
20
21
18
17
40
16
41
42
15
43
14
13
11
12
Figure 42.1
Page 42
7014-083E
September 1, 2008
R
D. Service Parts and Accessories
IMPORTANT: This is dated information. The most current information is located on the quadra-fire web site at
www.Quadrafire.Com. When ordering, supply serial and model numbers to ensure correct part.
SCHEMATIC LIST
Nbr
Description
Nbr
Description
11
Door Frame, not sellable
28
Cover, Feed Motor, Top
12
Glass Assembly, Center
29
Feed Motor & Spring Assembly
13
Glass Assembly, Side
30
Heat Exchanger Cleaning Rods
14
Door Latch Bracket
31
Blower, Convection
15
Grille, Louver, Top (Black, Gold or Nickel)
32
Exhaust Adapter Assembly
16
Ashpan Door (Panel, Front Access)
33
Exhaust Transition Assembly
17
Ashpan
34
18
Ash Catcher (Ash Lip)
35
Curtain, Side, Left
19
Heat Exchanger Tubes
36
Thermocouple Cover
20
Power Outlet & Thermostat Block
37
Gasket, Blower, Exhaust
21
Curtain, Side, Right
38
Mount, Door Hinge
22
Latch, Draw (3)
39
Thermocouple Holder
23
Heat Shield Extension, Top
40
Firepot Pull Rod Assembly
24
Junction Box & Wire Harness
41
Firepot, EZ Clean
25
Control Box
42
Igniter Bracket, not sellable
26
Vacuum Switch
43
Igniter (Heating Element)
27
Hopper, Top
SERVICE PARTS
Item #
Part Descsription, Alphabetical Order
Part No.
18
Ash Catcher (Ash Lip)
17
Ash Pan
812-4130
16
Ash Pan Door (Panel, Access Front)
410-7900
Baffle, Left
812-4200
Baffle, Right
812-4210
31
Blower, Convection
812-4900
34
812-3381
Component Pack (Includes firepot clean-out tool, touch-up paint, power cord & wiring harness to the
thermostat and manual, owner’s manual, label “Caution Fireplace Altered” warranty card and
“How-To-Operate” DVD)
812-4330
25
Control Box
SRV7000-205
28
Cover, Feed Motor, Top
410-7920
35
Curtain, Side, Left
812-4310
21
Curtain, Side, Right
812-4320
14
Door Latch Bracket
410-4912
Exhaust Plenum Clean-Out Plate
410-7910
Exhaust Adapter Assembly
510-5330
32
33
29
410-7830
Exhaust Transition Assembly
510-5340
Feed Motor
812-4421
Feed Motor Capacitor Jumper
230-2150
Feed Motor & Spring Assembly
812-3690
Septemer 1, 2008
7014-083E
Page 43
R
Item #
Part Descsription, Alphabetical Order
SKU
Feed Spring Only
SRV7027-024
Firepot Bolt, 1-1/4” long
225-0120
Firepot Floor (Slide Plate)
414-0290
Firepot Nut, 1/4-20
226-0090
40
Firepot Pull Rod Assembly (Linkage)
812-4140
41
Firepot, EZ Clean
812-3351
Fuse .7 amp, Junction Box
812-0380
Gasket (Rope), Door
842-2350
Gasket, 1200 ft per roll, 3/8”
240-0880
Gasket, 500 ft per roll, 1/2”
240-0940
Gasket, Blower, Exhaust
240-0812
37
Gasket, Exhaust Blower (Round White) between blower & housing
812-4710
Gasket, Firepot
510-0530
Gasket, Flue Adapter
240-0850
Gasket, Tadpole, 10 ft
842-5130
12
Glass Assembly, Center, 13-7/8 in. W x 11 in. H
510-5400
13
Glass Assembly, Side, 1 pc, 5-1/8 in. W x 11 in. H
510-5410
Grille, Bar Bottom
410-8330
23
Heat Sheld Extension, Top
410-7860
5
Hinge, Female
450-2910
Hinge, Hopper Lid
812-4220
Hopper Top
410-7730
27
Igniter Wire (5 ft) & 4 Ceramic Nuts
812-4520
43
Igniter, (Heating Element), 18 inches
SRV7000-462
24
Junction Box & Wire Harness
SRV7000-155
Knob, Firepot Pull Rod
200-0831
22
Latch, Draw
229-0640
Latch, Magnet
229-0631
38
Mount, Door Hinge
410-7290
Mount, Feed Motor
410-7172
Mount, Hopper Lid Support, Left
410-8200
Mount, Hopper Lid Support, Right
410-7410
Mount, hopper Lid Support, Top
410-7560
Outside Air Collar Assembly
7001-045
Outside Air Termination Cap
7001-044
Power Cord
812-1180
Snap Disc, #1, Convection Blower, 125 degree
230-0470
Snap Disc, #2, 200 degree
230-0900
Snap Disc, #3, Manual Reset, 250 degree
230-1290
8
Thermocouple
812-0210
36
Thermocouple Cover
812-1322
39
Thermocouple Holder
812-3171
7
Thumb Screw, pkg of 24
7000-223/24
Top only
SRV410-7960
Vacuum Switch
SRV7000-447
26
Page 44
7014-083E
September 1, 2008
R
Item No.
Accessories
Part No.
Brick Set
811-0601
Door Assembly, Black
DR-CB12-MBK
Door Assembly, Gold
DR-CB12-GD
Door Assembly, Nickle
DR-CB12-NL
Floor Protector
811-0730
Grille, Louver, Black
LVGRL-CB12-MBK
Grille, Louver, Gold
LVGRL-CB12-GD
Grille, Louver, Nickel
LVGRL-CB12-NL
Log Set, 3 pieces
811-0592
Outside Air Kit
811-0700
Panel & Trim Set, Small, 30” h x 40” w, Gold
SP-CB12I3040-GD
Panel & Trim Set, Small, 30” h x 40” w, Nickel
SP-CB12I3040-NL
Panel & Trim Set, Large, 33” h x 50” w, Gold
SP-CB12I3350-GD
Panel & Trim Set, Large, 33” h x 50” w, Nickel
SP-CB12I3350-NL
Rear Shroud Kit
811-0680
Rear Vent Kit
811-0690
Top Vent Kit, Rear Shroud
811-0650
Top Vent Adapter, 3 inch
811-0660
Top Vent Adapter, 4 inch
811-0670
Thermostat, Mechanical
812-3760
Thermostat, Programmable #9600
811-0520
Vent Adapter, 3 inch to 4 inch
811-0720
Zero Clearance Adjustable Trim Support, 2 inch to 10 inch
841-1000
Appliance
CB1200-I Insert, No Door or Grille (order door & grille separately)
Septemer 1, 2008
7014-083E
Part No.
CB1200I-B
Page 45
R
E. Warranty Policy
Hearth & Home Technologies LIMITED WARRANTY
Hearth & Home Technologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood,
pellet and electric appliances purchased from an authorized HHT dealer and installed in the United States of America or
Canada. Warranty starts with date of purchase by the original owner (End User) except as noted for replacement parts.
Warranty Period
Parts
Labor
1 Year
2 years
Gas
X
X
HHT Manufactured Appliances and Venting
EPA
Wood
Pellet
Electric
Wood
X
X
X
X
X
X
X
X
X
Venting
Components Covered
X
All Parts and Material Except
as covered by Conditions,
Exclusion, and Limitations
listed
Igniters, Electronic Components, and Glass
Blowers
X
3 years
X
5 years
3 years
7 years
3 years
10
years
1 year
X
1 year
X
Limited
Lifetime
90 Days
Molded Refractory Panels
X
Firepots
X
X
Castings & Baffles
X
X
Firebox, HHT Chimney, Termination & Heat Exchanger
Burners, Logs & Refractory
Firebox & Heat Exchanger
X
X
X
X
X
See Conditions, Exclusions, and limitations.
X
All Replacement Parts
9-01-08
CONDITIONS, EXCLUSIONS & LIMITATION OF LIABILITY
This warranty applies to the original owner and is transferable up to two years from date of purchase to the new
homeowner, provided the purchase was made through an authorized dealer or distributor of HHT, and the appliance
remains in its original place of installation.
The maximum amount recoverable under this warranty is limited to the purchase price of the product.
In no event shall HHT be liable for any incidental or consequential damages caused by defects in the product.
Adjustments, regular maintenance, cleaning and temporary repairs, or the failure to duplicate the problem in the home
is not covered under this warranty.
This limited warranty does not extend to or include surface finish on the appliance or terminations, door gasketing,
glass gasketing, glass discoloration, firebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or
corrosion on any of the metal surfaces, cast iron components, baffles, firepots, doors, or firebox area are not covered
by this warranty.
Noise resulting from minor expansion, contraction, or movement of certain parts is normal and complaints related to
this noise are not covered by this warranty.
4021-645A 09-01-08
Page 46
7014-083E
September 1, 2008
R
Hearth & Home Technologies LIMITED WARRANTY (Cont’d)
HHT’s obligation under this warranty does not extend to damages resulting from: (1) installation, operation or maintenance of the appliance not in accordance with the installation instructions; operating instructions and the listing
agent identification label furnished with the appliance; (2) installation which does not comply with local building codes;
(3) shipping, improper handling, improper operation, abuse, misuse, accident or unworkmanlike repairs; (4) environmental conditions, inadequate ventilation or drafting caused by tight sealing construction of the structure or handling
devices such as exhaust fans or forced air furnaces or other such causes; (5) use of fuels other than those specified
in the operating instructions; (6) installation or use of components not supplied with the appliance or any other components not expressly authorized and approved by HHT; and/or (7) modification of the appliance not expressly authorized and approved by HHT in writing.
This warranty does not apply to non-HHT venting components, hearth components or other accessories used in conjunction with the installation of this product.
This warranty is void if the appliance has been over-fired or operated in atmospheres contaminated by chlorine,
fluorine, or other damaging chemicals the appliance is subject to prolonged periods of dampness or condensation, or
there is any damage to the appliance or other components due to water or weather damage which is the result of, but
not limited to, improper chimney or venting installation.
HHT’s liability under this warranty is limited to the replacement and repair of defective components or workmanship
during the applicable period. HHT may fully discharge all of its obligations under such warranties by repairing the
defective component(s) at HHT’s discretion. Shipping costs are not covered under this warranty.
Some states do not allow exclusions or limitation of incidental or consequential damages, so those limitations may not
apply to you. This warranty gives you specific rights; you may also have other rights, which vary from state to state.
EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE
WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF
THE WARRANTY SPECIFIED ABOVE.
This Limited Warranty is effective on all HHT appliances sold after September 01, 2008 and supersedes any and all warranties currently in existence.
If warranty service is needed, you should contact your installing dealer. If the installing dealer is unable to provide necessary parts or components, contact the nearest authorized HHT dealer or supplier.
4021-645A 09-01-08
Septemer 1, 2008
7014-083E
Page 47
R
O T
T
O
TO :
Hearth & Home Technologies
1445 North Highway
Colville, WA 99114
Division of HNI INDUSTRIES
www.quadrafire.com
Please contact your Quadra-Fire dealer with any questions or concerns.
For the number of your nearest Quadra-Fire dealer
visit our website at www.quadrafire.com
NOTICE
• Important operating and • Read, understand and
follow these instrucmaintenance instructions for safe installations included.
tion and operation.
T
O
N RD
O A
D SC
I
D
DO NOT DISCARD THIS MANUAL
• Leave this manual with
party responsible for use
and operation.
We recommend that you record the following pertinent
information for your CB1200-I PELLET INSERT
Date purchased/installed:
Serial Number:
Location on appliance:
Dealership purchased from:
Dealer phone:
Notes:
This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322,
4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708,
5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743,
6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687,
6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, 6769426, 6774802, 6796302, 6840261,
6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749,
2195264, 2225408, 2313972; (Australia) 780250, 780403, 1418504 or other U.S. and foreign patents pending.
Page 48
7014-083E
September 1, 2008

Quadra-Fire CB1200-i

Transcription

Similar documents

Lightning Fast Search Solutions for the Enterprise

save these instructions important safeguards

Pellet insert

profile™ pellet stoves and inserts

INTEGRA II Customize with color to add an element of design to

View PDF File - ConcessionStands.com

Foot Massager Manual

ACCENTRA Pellet INSeRt

Free up your voice IT resources with faster time-to

Manual