EZ-ON Tool Kit GEM Part Number: EZ-TK T568A / T568B

®
The EZ-RJ45® Connectors, (see cable
connector selector chart below) simplify twisted
pair terminations by allowing the wire to be
inserted through the connector and out the
front. This allows the technician to easily verify
the proper wiring order (the 568A and 568B
wiring chart below). Electrical performance of
the termination is optimized by pulling the
connector down over the cable jacket and
seating it tightly in the rear of the connector. It
also guarantees that the wires will be properly
flush to the front of the connector.
T568A / T568B Wiring Chart
Wire Number
T568A
T568B
1
W/G
W/O
2
G
O
3
WO
W/G
4
BL
BL
5
W/BL
W/BL
6
O
G
7
W/BR
W/BR
8
BR
BR
For use with solid and standard conductor
EZ-ON Tool Kit
GEM Part Number:
EZ-TK
Gem Baluns use T568B Below
1. White / Orange
2. Orange
3. White / Green
4. Blue
5. White / Blue
6. Green
7. Brown / White
8. Brown
Tool Kit Contains:
1 Crimp Tool - P/N GET-EZCT
50 EZ-ON RJ45 CAT5
Connectors - P/N CAT5-EZP
1 Wire Cutter - P/N GWC
Cable - Connector - Selector Chart
Cable
3, 5, 5E
5 Shielded
6
11, 12
Connector
CAT5-EZP (50 pack)
CAT5-EZSTP (10 pack)
CAT6-EZPTP (10 pack)
CAT11-EZPTP (10 pack)
Crimp Tool
GET-EZCT
GET-EZCT
GET-EZCT
GET-EZCT
Crimp Tool
TEVELEC LIMITED, 5350 Timberlea Blvd.,
Mississauga, ON L4W 2S6 Tel. (905) 624-5241
920-A River Street - Windsor, CT 06095 - Toll Free:Fax
888-436-4195
- Tel: 860-683-0392
Fax: 860-683-0396
(905) 625-2462
Toll Free -1-877-TEVELEC
e-mail: gembpitcher@aol.com - Web: www.gemelec.com
sales@tevelec.com
Tevelec.com
®
Cable Assembly Procedures
1. Strip off approximately two (2) inches of outer jacket.
Connector
Cable
2. Straighten and align pair wires per T568B. Trim pair wires with
the cutter built into the EZ-RJ45® hand tool.
3. Insert wires into EZ-RJ45® connector.
Connector
Cable
4. Pull tight to ensure jacket is about 1/4 to 5/16 of an inch into the
connector.
5. Verify wire locations and orientation.
Connector
Cable
6. Insert EZ-RJ45® connector into hand tool.
7. Verify connector is completely seated and cable is fully inserted.
Tool
Tool
8. Squeeze handle.
Connector
Cable
9. Remove excess wires.
Connector
Cable
10. Check jacket strain relief.
11. Check that contacts are all engaged.
12. Check that contact dividers are not damaged.
13. Check to see if both ends of the cable have been terminated,
perform continuity test.
Manufactured by SullStar Technologies, Inc. Patented:5.996.224. 6.017.237 & 6.105.229 & Foreign Patents. Patents insured.
EZ-RJ45® is a registered trademark of SullStar Technologies, Inc.
TEVELEC LIMITED, 5350 Timberlea Blvd.,
Mississauga, ON L4W 2S6 Tel. (905) 624-5241
Fax (905) 625-2462 Toll Free 1-877-TEVELEC
sales@tevelec.com
Tevelec.com