STUDER Equipment - Fritz Studer AG

Transcription

tsch
STUDER Equipment
1
2
Contents
Page4
ClampingCentres
Collets
Chucks & clamping heads
Page16
Page 34
Machine periphery
Page 38
Clothing & accessories
DressingDiamonds
Page 20
GrindingExternal grinding
Internal grinding
3
Clamping
4
5
Clamping Centres
Full centre
1.Full centre A short dia. 35mm (1.377“) MT4.
2.Full centre A short dia. 26mm (1.023“) MT3.
3.Full centre A long dia. 20mm (0.787“) MT2.
Article number:
1.A2810030A
2.A0709017A
3.A0138004A
6
Clamping / Centres
Insert for centres
1.Insert for centres MT4 for universal
workhead ISO50 incl. locking plate and
driver (driver pin dia. 10mm (0.394“)).
2.Insert for centres MT3 for universal
workhead ISO50 incl. locking plate and
driver (driver pin dia. 10mm (0.394“)).
3.Insert for centres MT4 for chuck or motor
workhead ISO50 incl. driver plate and driver
(driver pin dia. 10mm (0.394“)).
4.Insert for centres MT3 for chuck or motor
workhead ISO50 incl. driver plate and driver
(driver pin dia. 10mm (0.394“)).
Article number:
1.A2439707A
2.A2439704A 3. A2439703A 4. A2439702A
7
Adaptor for centres
Carriers
1.Adaptor for centres MT3 for fitting
taper MT4.
2.Adaptor for centres MT2 for fitting
taper MT4.
Set of carriers for dia. 10-50mm (0.39-1.97“),
set consists of 1 pieces for the following dia.
ranges: Up to max. dia. 10mm (0.39“), dia.
16mm (0.63“), dia. 25mm (0.98“), dia. 40mm
(1.57“), dia. 50mm (1.97“).
Article number:
1.A2805017A
2.A2030026A
8
Article number: A1809617A
Clamping / Centres
Driver
1.Drive plate:
Drive plate with integrated drive fork for
the backlash-free driving of a workpiece
carrier. Note: Needs basic drive plate.
2.Basic drive plate:
Basic drive plate for workhead with a
spindle nose dia. 110mm (4.33“). For use
with rotating centre and mounting of a
tangential force-free drive fork and/or
drawdown springs for steady rest applications.
Article number:
1.A2439854A
2.A2439856A
9
Driving fork
Simple driving fork for driving a workpiece
carrier with no backlash. Can be used instead
of a drive pin dia. 10mm (0.39”). For workhead
with fitting taper ISO50.
10
Clamping / Collets
Clamping Collets
Collets
1.Set of 37 collets W20 dia. 2-20mm
(0.078-0.787“), in steps of 0.5mm (0.019“).
2.Set of 47 collets W25 dia. 2-25mm
(0.078-0.984“), in steps of 0.5mm
(0.019“).
3.Set of 55 collets B32 dia. 3-30mm
(0.118-1.181“), in steps of 0.5mm
(0.019“).
Article number:
1.A5558102
2.A5558202
3.A5557248A
11
Clamping Chucks & clamping heads
Intermediate flange
Bayonet head
Intermediate flange for bayonet head or
combination bayonet head with interface
for mounting of a ring sensor.
Bayonet head size 6, DIN 55027, 55022 for
fitting taper ISO50. Enables fast and easy changeover of live chucks. Power supply through
drawbar for power chucks possible.
Note: Must be dismounted when using centres.
12
Clamping / chucks & clamping heads
Combination bayonet head
Combination bayonet head size 6, DIN55027,
55022 with integrated, revolving centre adaptor
MT4 for workhead with fitting taper ISO50. Incl.
driver (driving pin dia. 10mm (0.394”) for use
with centres.
Enables quick and simple change over between
spindle mounted clamping devices for live spindle grinding and MT4 centres.
Note: Not for use with power chucks. Power
supply through drawbar is not possible.
13
Magnetic chuck
1.Magnetic chuck dia. 230mm (9.06“) for
bayonet head size 6, DIN 55027, 55022
(permanent magnet).
2.Magnetic chuck dia. 165mm (6.496“) for
bayonet head size 6, DIN 55027, 55022
(permanent magnet).
General note for the magnetic chuck: Foot
pedal recommended for set up (see p. 36).
Article number:
1.A2439624A
2.A2439623A
14
Clamping / chucks & clamping heads
Camlock head
Camlock head size 6, DIN 55029 for spindle
nose dia. 110mm (4.33“) with interface
for mounting of ring sensor. Enables quick and
simple change of clamping devices for live
spindle grinding.
15
Dressing
16
17
Dressing Diamonds
Single point diamond
Single point diamond 0.45 carat 55 deg. R
0.5mm (0.019“) with fitting taper MT1
shortened (clamping length 19mm (0.748“)).
18
Dressing / Diamonds
Needle fleece
Needle fleece type CVD-3-0640 DV/10,
height 10mm (0.394“), length 18mm (0.709“)
with fitting taper MT1 shortened
(clamping length 19mm (0.748“)).
Impregnated diamond
1.Impregnated diamond for grinding wheel
grit 120-320 with fitting taper MT1
2.Impregnated diamond for grinding wheel
grit 60-100 with fitting taper MT1
Article number:
1.A5560012A
2.A5560009A
19
Grinding
20
21
Grinding External
grinding
Wheel adaptor
1.Wheel adaptor dia. 400mm (15.748“) with bore
127mm (5“). Width 25-63mm (0.984-2.480“)
form 1 (80mm (3.149“) form 5) for tapered shaft
ends 1:10 nominal dia. 63mm (2.480“).
Incl. balancing segments and graduation.
127mm (5“). Width 25-63mm (0.984-2.480“)
203.2mm (8“). Width 32-80mm (1.260-3.150“)
203.2mm (8“). Width 32-63mm (1.259-2.480“)
Article number:
1.A2432794A
2.A2912674A
22
3.10022985
4.A2432795A
Grinding / External grinding
Spacer ring
1.Spacer ring 15mm (0.590“) with bore
203.2mm (8“).
127mm (5“).
203.2mm (8“).
127mm (5“).
Article number:
1.A2012243B
2.A2413335
3.A2012241B
4.A2713043A
23
Support ring
Support ring for wheel sets dia. 203.2mm (8“) /
500x40-100 F1 / 125 F5
Article number: A2412814
24
Contact ring sensor
Contact ring sensor passive with on roller bearings external grinding spindle for cut-in detection in external grinding and cut-in detection on
fixed or rotating dressing tools.
Incl. adjusting gauge for customer assembly.
Feeder cable 1.5m (1.64yd) and connecting cable
3.1m (3.39yd) (plugable, directly on the back wall
of the grinding face detection device 3-pole).
Note:
Electronic cut-in detection Sensitron 2 required.
25
Locating pin
Extraction tool
Locating pin (length 500mm (19.685”) for more
ergonomic grinding wheel change, valid for
spindles with shaft nominal dia. 73mm (2.874”).
Usable only for motor spindles with a solid
shaft.
Extraction tool for wheel adaptors, for shaft end
with nominal dia. 44mm (1.732“).
26
Steady rest
1.Steady rest closed for dia. 90-230mm
(3.543-9.055“) (centre height 275mm
(10.826“), broad table profil) with cylindric ity correction and fine adjustment for jaws.
2.Steady rest closed for dia. 5-140mm
(0.196-5.511“) (centre height 225mm
(8.858“), broad table profil) with cylindricity
correction and fine adjustment for jaws.
Article number:
1.10025478
2.A2414678A
27
Prism supports
Steady rest
1.Prism supports (2 pieces) for dia. 15-150mm (0.590-5.905“)
(centre height 225mm (8.858“), broad table profile).
1.Two-point steady for dia. 4-88mm (0.157-3.464“)
(for centre height 225mm (8.858“), broad table profile).
2.Prism supports (2 pieces) for dia. 50-260mm (1.968-10.236“)
(centre height 225mm (8.858“), broad table profile).
2.Two-point steady for dia. 4-88mm (0.157-3.464“)
(for centre height 275mm (10.826“), broad table profile).
Article number:
1.A2414724A
2.10016142
Article number:
1.A2414716A
2.10025502
28
Grinding wheel lifting device
Grinding wheel lifting device
Suspension bracket for grinding wheel change
with lifting device on the customer side. (e.g.
hall crane). Maximal weight on suspension
bracket 850N / 191lb.
Swivel arm within the machine enclosure
with suspension bracket for changing grinding
wheels. Maximum load on suspension bracket
850N (191lb). Suspension bracket can be taken
over with a lifting device belonging to the
customer.
Article number: 10020932
29
Balancing arbor
Balancing apparatus
1.Balancing arbor for grinding wheels with nominal dia. 73mm
(2.874“), length 310mm (12.205“), for balancing equipment
dia. 500mm (19.685“) up to dia. 600mm (23.622“).
Balancing equipment dia. up to 600mm
(24.622“) for static balancing of the grinding
wheel outside of the machine.
Note: Requires the respective balancing arbor
for grinding wheels.
2.Balancing arbor for grinding wheels with nominal dia. 44mm
(1.732“), length 215mm (8.465“), for balancing equipment
dia. 400mm (15.748““).
Article number:
1.A2912225A
2.A0852122
30
Dynamic balancing
Portable 1-plane MPM 3.BMT100M.24 dynamic
balancing device with an operating voltage of
24V DC. Display unit for manual adjustment of
the balancing segments on a one-sided grinding wheel adaptor after a dynamic imbalance
check. Including transport case.
Notes:
– One unit can be used for more than one
machine. Free for serie: 1-120.
–Requires balancing sensor MPM (1 x per
external grinding spindel), connecting cable
set for a portable balancing unit MPM
BMT100, balancing-sensorik MPM and
connecting part.
Article number: A2912654B
31
Grinding Internal grinding
Internal grinding quill
Article number:
1.A5552324A
2.A5551945A
3.A5551530A
4.A5552218A
5.A5552288A
32
6.A5552415A
7.A5551533A
8.A5551516A
9.A5552265A
10.A5552276A
1. Internal grinding quill HJND 28-25115
dia. 25 x 115mm (0.984 x 4.527“)
dia. 40 x 170mm (1.574 x 6.692“)
dia. 20 x 30mm (0.787 x 1.181“)
dia. 12 x 20mm (0.472 x0.787“)
dia. 12 x 50mm (0.472 x 1.969“)
dia. 4 x 12mm (0.157 x 0.472“)
dia. 5 x 14mm (0.196 x 0.551“)
dia. 50 x 200mm (1.968 x 7.874“)
dia. 4 x 12mm (0.157 x 0.472“)
10.Internal grinding quill HJND 60-945
dia. 9 x 45mm (0.354 x 1.772“)
Grinding / Internal grinding
Set-up tailstock
Set-up tailstock with fitting taper MT3
(CH 175mm (6.89“)). Set-up aid for setting 3-jaw
steady rest.
33
Machine periphery
34
35
Machine periphery
Foot pedal
Air-filter
Filter paper
1.Approval footpedal for the execution of
movements with open operating doors (with
overtravel switched off). Facilitates the
set-up of internal grinding spindles and the
alignment of workpieces in the chucks.
Connection cable length 3.5m (3.83 yd).
Air-filter for wheelhead motor (air-cooling).
1.Filter paper medium OL40, roll of 200m
(218.7 yd), width 1000mm (39.4“).
2.Approval footpedal (2-channel).
Article number:
1.A1390739A
2.A1390791A
36
2.Filter fleece, fine OL50, recommended for
emulsion; roll of 150m (164 yd), width
1000mm (39.4“).
Article number:
1.A5490116A
2.A5490115A
Machine periphery
Machine platform
Platform for the machine operator dimensions
1400mm (55.1“) x 500mm (19.7“) x 200mm (7.9“).
Grinding wheel storage stand
Storage stand for 5 grinding wheels with flange
up to dia. 500mm (19.7“). Area: 700mm (27.6”)
x 700mm (27.6”), height: 1100mm (43.3”).
37
Clothing & Accessories
38
39
Ballpoint pen
Writing set
Ring binder notepad
High quality Caran d‘Ache ballpoint pen with
the STUDER logo und claim.
Caran d‘Ache ballpoint pen and propelling pencil
(size: 0.7mm ) with logo.
5mm pad, 60 pages, header on both sides.
40
Umbrella
Light-grey umbrella with a wooden grip: openned dia. 94cm. Auto opener, with STUDER logo.
Baseball cap
Light-grey baseball cap with embroidered logo
in white on the leftside. One size for all, with
adjustable fastening.
41
Men‘s polo shirt
Men‘s T-shirt
Fleece vest
STUDER polo shirt in light-grey with embroidered logo on the breast and the claim „The Art
of Grinding“ on the left arm. Available in sizes
S-XXL. Material: 100% Cotton.
STUDER T-shirt in dark-grey with embroidered
logo on the breast, „The Art of Grinding“ on
the left arm. Available in sizes S-XXL. Material:
100% Cotton.
STUDER shortarm vest in dark-grey with a
STUDER logo on the breast. Available in sizes
S-XXL. Material: 100% polyester.
42
43
ISO 9001
VDA6.4
certified
10.2012/ Printed in Switzerland
Fritz Studer AG
CH-3602 Thun
Telephone +41-33-439 1111 · Telefax +41-33-439 1112
www.studer.com

STUDER Equipment - Fritz Studer AG

Transcription

Similar documents

rotary workholding