3d-series 3-way panhead

3D-SERIES 3-WAY PANHEAD
Operating Instructions
Thank you for making Induro your choice for
professional photographic gear. Your Induro gear
is manufactured to provide years of dependable
service. In order to obtain optimum satisfaction
and performance we suggest that you carefully
read these instructions and provide them to
anyone who may also use your Induro gear.
Camera Screw
Quick Release Plate
Horizontal Tilt Lock
Bubble Level
Plate Locking Lever
Security Locking Lever
Pan Lock
Base
Front/Rear Tilt Lock
USER NOTICE
cc Do not exceed the maximum specified
load capacity (see Specification chart)
cc Always ensure that leg and head locks
are tightly engaged before mounting a
camera on the tripod
cc Do not use the tripod below
temperatures of -4°F or above +158°F
(-20°C / +70°C)
cc Always clean and dry the tripod after it
has been exposed to wet, dusty, sandy
or salty conditions. Your tripod is not
recommended for use in salt water.
If required clean tripod using a mild
soap solution applied with a soft cloth
and follow by wiping down with fresh
water. Remove any dust, dirt or sand
from all leg locks, leg lock levers,
leg sections and all moving parts.
cc Do not leave the product in the sun
for prolonged periods and avoid high
temperature exposure
cc Avoid leaving the tripod unattended in
areas where people could trip over the
tripod and get hurt
cc Remove camera, lens, and all gear
from the tripod when transporting
the tripod
cc For your safety, don’t let your Induro
tripod come in contact with any
electrical power source
1
2
3
4
5
6
Install by screwing the
head clockwise on to the
3/8 thread mounting thread
of tripod plate. Once it is
hand tight secure by fully
tightening the three head
locking screws from below.
Horizontal rotation or
panning can be easily
accomplished by first
loosening the pan lock
and then rotating head on
platform. Once in position
tighten the pan lock securely.
A patented dual lock
quick release system
when used properly offers
two levels of security for
your gear. To remove the
quick release plate, squeeze
both levers and pull the
larger plate locking lever
out. The quick release plate
will disengage so it can
be removed.
Front to rear angle or
tilt adjustments can
be easily accomplished
by first loosening the tilt
lock (be sure to hold on
firmly to balance weight of
the camera). Position as
required and then tighten
handle securely. You have
the same control and lock
available on the other axis
for horizontal angle or
tilt adjustments.
To reconnect the quick
release plate, insert the
angled part of the plate into
the groove on the opposite
side of the locking lever and
press down flat. The locking
levers will automatically
engage the locking system
and the locking levers will
return to the safety lock
position. Press the plate
locking lever in firmly
to secure.
Depending on your
requirements you may
find it convenient to reorient
the camera or lens 90 degrees
on the quick release and
remount so that the tilt
controls give you different
positioning support.
MODEL #
3D-M-23
3D-L-34
483-002
483-003
QR-3D-34-38L**
QR-3D-23-38M**
QR-3D-01-14S*
CAMERA MOUNT
TILT RANGE
+90°/-25°
+90°/-30°
+65°/-65°
FRONT
+90°/-35°
+90°/-30°
+90°/-25°
HORIZONTAL
360°
360°
360°
PANNING
RANGE
3&4
2&3
0&1
MATCHING
TRIPODS
2.1
1.8
1.1
LB
1.0
0.8
0.5
KG
WEIGHT
26.5
17.6
11.0
LB
12.0
8.0
5.0
KG
LOAD
INDURO Camera Support Gear | 8 Westchester Plaza, Elmsford, NY 10523 | T 914-347-3300 | F 914-347-3309 | info@indurogear.com | indurogear.com
* 1/4-20 Quick Release Plate; * * 1/4-20 & 3/8-16 Quick Release Plates
3D-S-01
483-001
3-Way Panhead 3D-Series
CAT #
SPECIFICATIONS