italinox brochure

An ASSA ABLOY Group company
N
S
U
ESS
O
I
V
OF WINDOW ACCESSORIES FOR
TOP-HUNG OUTWARD PROJECTING
WINDOWS , RIVALU OFFERS
YOU A COMPLETE RANGE OF
SOLUTIONS FOR THE CLOSING OF
YOUR WINDOW
NC
AS A SPECIALIST MANUFACTURER
E
IMPER
E
C
N
A
M
R
O
F
R
E
P EN A
DUR
These single or multi-point
locking systems meet the strictest
requirements for both air and water
tightness on any window size.
Our handles offer you a large range
of designs and colours.
These fittings are complementary to
ITALINOX friction hinges
CHARACTERISTICS
•Our fittings are suitable for traditional outward projecting window profiles, structural glazing and semi-structural glazing profiles.
•The single point locking system is ensured by means
of following handles :
VECALU lever closer,, LAG and BAG.
•The multi-point locking system ensures 2 or 4 locking
points (or more) with only one central handle : internal
mechanism VECTRALE or “CE”” Cremone Bolt combined
with multi-point fitting.
2
•A multi-point locking is recommended for windows with a
width up to 1500mm.
CLOSING DEVICES
Skill in locking
3
Vecalu
CHARACTERISTICS
•Suited to structural glazing and
semi-structural glazing profiles.
•Progressive locking provided by a
stainless steel latch and a polyamide
turn roller of 10mm diameter on an
aluminium anodized keeper.
•3 different models of roll lever closer
and 2 models of keepers are available
according to the thickness of sash
profile and chamber.
•Roll lever closers with left or right
operating way.
•Concealed fixing of keeper and
VECALU handle.
•Natural anodized or coated finish.
4
CLOSING DEVICES
Single Point locking
Lever Closers
LAG 208
BAG 310
BAG OPALE
258
CHARACTERISTICS
BAG 307
•Suited to traditional outward window profiles,
structural glazing and semi- structural glazing
profiles.
•Progressive locking provided by a polyamide turn
roller and an aluminium or polyamide rounded
keeper.
•Combinations possible with 3 models of handles
on 4 backplate types adapted to different sash
profiles.
•Handle with left or right operating way.
•Concealed or visible fixing of the keeper.
•Natural anodized or coated finish (OPALE model
is not available in anodized version).
GA11
GT8
5
Vectrale Mechanism
with spindle
REF 6805
CHARACTERISTICS
•Suited to structural glazing and
semi-structural glazing profiles.
•Invisible internal mechanism – only the
handle is visible.
•Reduced space required within the profile
chamber.
•Indexed quarter turn operation.
•Bi-directional operation.
•Concealed fixing.
•Use handle alone with VECTRALE
mechanism with spindle ref.6805.
•Use handle on backplate with VECTRALE
mechanism without spindle ref.6815.
•5 different models of handles available
(with or without backplate).
•Complementary to our fittings with turn
roller or adjustable roller.
•Coated finish - note that PARAPHE and
BERCY models are also available in satin
silver anodized finish.
6
BERCY
REF 7205
PARAPHE
REF 7206
CLOSING DEVICES
Multi-point locking
Vectrale Mechanism
without spindle
REF 6815
ESTIVALE
Offset handle REF 9068
BORÉALE
REF 9748
OPALE
REF 9088
The handles are
available on
backplate in order to
be fitted with the
VECTRALE mechanism
without spindle
ref.6815.
7
“CE” CREMONE BOLT
OPALE
CHARACTERISTICS
•Suited to traditional outward projecting
window profiles, structural glazing and
semi-structural glazing profiles.
•Above or front fixing.
•Indexed quarter turn operation.
•Bi-directional operation.
•Concealed fixing.
•4 different handle models and one version
with square socket.
•Offset handle ESTIVALE available either in left
or right operating way.
•Complementary to our fittings with turn roller
or adjustable roller.
•Coated finish – note that PARAPHE and BERCY
models are also available in satin silver
anodized finish.
8
PARAPHE
CLOSING DEVICES
Multi-point locking
ESTIVALE
OPALE
BERCY
HANDLE
WITH SQUARE
SOCKET
9
Multi-point locking
Fittings
DRIVER
REF 3397
CORNER
GEAR
REF 3225
REF 5586
TURN
ROLLER
REF 5223
ADJUSTABLE
ROLLER
SOCKET
REF 3367
CHARACTERISTICS
•2 to 4 locking point fitting, made of zamak.
•Suitable for 15 x 20 window sash groove.
•Available with adjustable roller or turn roller.
•2 models of drivers available allowing both above and
front fixing of the “CE” cremone bolt.
•Corner gear implementation by means of a stainless
steel pin.
•Progressive locking operation thanks to a ramp-keeper.
•White zinc plated finish.
10
KEEPER
REF 3561
CLOSING DEVICES
Additional
Accessories
RETAINER
ARM
Retainer arm releasable either by hand
(ref. 5901) or with an hexagonal wrench (ref 5900).
Suitable for 16 or 21 mm chambers.
Adjustable brake located into a stainless steel slide.
STRENGTHENING
SET
REF 5249
SPACER
SET
2 models
adapted
to 16 mm chamber
(ref.7352)
or 21 mm chamber
(ref.7176).
Provides one locking
point at the level of the
upper crossbar.
The number and
position depends
on the window
width and the desired
Air-Water-Wind
performance.
11
Vecalu
Left operating way
Right operating way
32
x1
1
48
2 holes Ø5.3
21
59
x1
1
7.5
17.5
A
C
B
30
2 holes Ø3.4
10
12
CLOSING DEVICES
164
11
30
38
150
30
13.5
REF GV21
17.5
11
REF GV16
Chamber A =16 mm
GV 21 Keeper
-
-
-
MAINTENANCE
-
Each year check and ensure all fixings are
suitably tightened and lubricated as required.
-
-
-
-
-
+
-
+
-
-
+
GV 16 Keeper
38 to 41
+
-
33 to 38
+ +
VECALU I 38 (B = 32 mm)
Choice of models depends on dimensions
“A” and “C”. Please refer to the table opposite.
35 to 39
+
-
+
VECALU I 33 (B = 28,5 mm)
CHOICE OF MODELS
32 to 35
+
VECALU I 28 (B = 25 mm)
28 to 32
+
Dimension C (mm)
Chamber A =21 mm
13
Roll lever closers
FIXING FLANGE 208 OR 258
shown here with profiled handle (LAG)
8
11 MAX.
A
20 or 25
60
43
D
FIXING FLANGE 310
30
shown here with GOLF handle (BAG)
8
20
11 MAX.
A
9.8
30
19
48
11
60
D
FIXING FLANGE 307
shown here with OPALE handle (BAG)
30
60
20
11
11 MAX.
1,5
A
6.8
26.5
40
30
8
14
D
CLOSING DEVICES
60
CHOICE OF MODELS
Dimensions “A” and “B” have to be specified
when ordering.
For choice of fixing flanges, handles and keepers
please revert to the table below.
22
43
REF GA / GN
MAINTENANCE
B
- Each year check and ensure all fixings are
suitably tightened and lubricated as required.
60
22
43
REF GT
BAG GOLF
LAG
-
+ +
BAG OPALE
258
307
310
+ + +
208
+ + +
CHOICE OF FIXING FLANGES ACCORDING TO HANDLE MODELS
+
Handle models
B
-
CHOICE OF KEEPERS
Keeper model
GN 8
GN 11
GA 8
GA 11
GT 8
GT 11
Material
Nylon*
Nylon*
Aluminium
Aluminium
Aluminium
Aluminium
Dimension B ( mm )
8
11
8
11
8
11
* Grey or black Nylon
15
Vectrale Mechanism
with spindle
15
1.5 3
shown here with BERCY handle 7205
A
4.5 MAX.
20
To ensure flush fit of the tapped
rivets it is necessary to trim back
the 6.2mm diameter holes
(chamfer 0.2mm to 0.3mm).
4.5 MAX.
21
14
WARNING
20.5 11.5
Vectrale mechanism with spindle
ref. 6805 is suited to window sash
profiles of 12mm to 19mm thickness.
More references are also available for
window sash profiles up to 31 mm.
Please contact us.
VECTRALE mechanism is directly
connected to sash rods.
IMPLEMENTATION
1 hole Ø18
After the installation of the mechanism
into the profile, insert the handle and
its ring into the spindle and press the
handle against the profile while at
2 holes Ø6.2* the same time tightening the screw
until the spindle is punched.
MAINTENANCE
Each year check and ensure all
fixings are suitably tightened and
lubricated as required..
43
16
CLOSING DEVICES
Vectrale mechanism
without spindle
1.5 3
shown here with PARAPHE handle on backplate
15
20
WARNING
The length of screws and the outgoing
part of the spindle vary according to
the dimension of the sash “A”. It is
imperative that the dimension of “A”
is accurate at the time of ordering.
4.5 MAX.
21
14
A
4.5 MAX.
15 MIN.
20.5 11.5
VECTRALE mechanism is directly
connected to sash rods.
MAINTENANCE
Each year check and ensure all
fixings are suitably tightened and
lubricated as required.
1 hole Ø18
2 holes Ø10.5
2 holes Ø5.5
43
17
“CE” Cremone bolt
ABOVE FIXING
4.5 MAX.
21
4.5 MAX.
shown here with PARAPHE handle model
19 MIN.
24
87 98
x6
2
2 holes Ø7.2*
WARNING
To ensure flush fit of the tapped rivets it is
necessary to trim back the 7.2mm diameter holes
(chamfer 0.2mm to 0.3mm).
Drivers ref. 5586
“CE” Cremone bolt
Handles
Paraphe
Bercy
Opale
Estivale
Square socket
System
references
4484
5758
8992
9847
5244
18
“CE” Cremone Bolt is suited to window sash
profiles of 12mm to 19mm.
The length of screws and the outgoing part of the
spindle vary according to the dimension of the
sash “A”. It is imperative that the dimension of
“A” is accurate at the time of ordering.
MAINTENANCE
Each year check and ensure all fixings are
suitably tightened and lubricated as required.
CLOSING DEVICES
“CE” Cremone bolt
FRONT FIXING
21
15.5 MIN.
4 MIN.
shown here with OPALE handle model
98
6
81 x
2
75
x1
2
2 holes Ø7.2*
WARNING
To ensure flush fit of the tapped rivets it is
necessary to trim back the 7.2mm diameter holes
(chamfer 0.2mm to 0.3mm).
Drivers ref. 3397
“CE” Cremone bolt
Handles
Paraphe
Bercy
Opale
Estivale
Square socket
System
references
4473
5757
8993
9848
5244
The successful installation of this closing
mechanism is dependent on the characteristics
of the sash profile. Please contact us for more
details.
MAINTENANCE
Each year check and ensure all fixings are
suitably tightened and lubricated as required.
19
HANDLE AXIS
Y (from the inside of sash groove)
48
Fittings with adjusta
T2
T3
VECTRALE MECHANISM
T2
T1
D
“CE” CREMONE BOLT – ABOVE FIXING
T2
T1
A
48
“CE” CREMONE BOLT – FRONT FIXING
LR/
T1
2126
LR
(wid
B
t h fr
om
th
C
e in
si de
of sa
Rods cutting
14.5
19.5
4.5
2.5
20
8
sh g
roov
e)
X
8
E
Ø6
48
CLOSING DEVICES
able rollers
FITTING DESCRIPTION
To ensure the correct system is used with the
correct handle, please refer to the table below.
IMPLEMENTATION
HOW TO CREATE YOUR FITTING
“CE” Cremone Bolt
above-fixing
VECTRALE
mechanism
Sign
References
“CE” Cremone Bolt
front fixing
2 POINTS 4 POINTS 2 POINTS 4 POINTS 2 POINTS 4 POINTS
A
Driver
5586
-
-
2
2
-
-
B
Driver
3397
-
-
-
-
2
2
C
Roller socket
3367
2
2
2
2
2
2
D
Corner gear
3225
-
2
-
2
-
2
E
Roll catch
3561
2
4
2
4
2
4
After the profiles and rods have been machined
(refer to second table), clean and lubricate the
15 x 20 sash groove with a non-acid lubricant.
FIRST USE
Lubricate keepers with a non-acid lubricant.
Adjust the rollers +/- 1mm depending on the
pressure required.
MAINTENANCE
Each year check and ensure all fixings are
suitably tightened and lubricated as required.
> FRONT FIXING
RODS CUTTING
“CE” Cremone Bolt
above-fixing
VECTRALE
mechanism
“CE” Cremone Bolt
front fixing
Rod
Qty
T1
2
X - 106
-
X - 121
-
T2
2
-
LR/2 - 177
-
LR/2 - 192
-
LR/2 - 211
T3
2
-
Y - 152
-
Y - 152
-
Y - 152
2 POINTS 4 POINTS 2 POINTS 4 POINTS 2 POINTS 4 POINTS
X - 140
-
2 holes Ø3.8
0,5
> ABOVE FIXING
Roller adjustment
2 holes Ø3.8
0,5
21
HANDLE AXIS
Y (from the inside of sash groove)
48
Fittings with turning
T2
T3
VECTRALE MECHANISM
T2
T1
D
T2
“CE” CREMONE BOLT – ABOVE FIXING
T1
A
48
“CE” CREMONE BOLT – FRONT FIXING
T1
LR/
2126
LR
(wid
t h fr
B
C
om
th
e in
si de
of sa
Rods cutting
14.5
19.5
4.5
2.5
22
8
8
X
sh g
roov
e)
E
48
Ø6
CLOSING DEVICES
g rollers
FITTING DESCRIPTION
To ensure the correct system is used with the
correct handle please refer to the table below.
IMPLEMENTATION
HOW TO CREATE YOUR FITTING
VECTRALE
mechanism
Sign
References
“CE” Cremone Bolt
above-fixing
“CE” Cremone Bolt
front fixing
2 POINTS 4 POINTS 2 POINTS 4 POINTS 2 POINTS 4 POINTS
After the profiles and rods have been machined
(refer to second table), clean and lubricate the
15 x 20 sash grove with a non-acid lubricant.
FIRST USE
Lubricate keepers with a non-acid lubricant.
A
Driver
5586
-
-
2
2
-
-
MAINTENANCE
B
Driver
3397
-
-
-
-
2
2
Each year check and ensure all fixings are
suitably tightened and lubricated as required.
C
Clip roller
5223
2
2
2
2
2
2
D
Corner gear
3225
-
2
-
2
-
2
E
Roll Catch
3561
2
4
2
4
2
4
> FRONT FIXING
RODS CUTTING
“CE” Cremone Bolt
above-fixing
VECTRALE
mechanism
“CE” Cremone Bolt
front fixing
Rod
Qty
T1
2
X - 34
-
X - 49
-
T2
2
-
LR/2 - 177
-
LR/2 - 192
-
LR/2 - 211
T3
2
-
Y - 79,5
-
Y - 79,5
-
Y - 79,5
2 POINTS 4 POINTS 2 POINTS 4 POINTS 2 POINTS 4 POINTS
X - 68
-
0,5
2 holes Ø3.8
> ABOVE FIXING
0,5
Turning roller
2 holes Ø3.8
23
Finishes
Any other
colour, please
contact us.
White
9010B
Black
9005S
Grey
AL9006 EL
Silver
Anodized
Bronze
1247
PROPERTY
Agence MARLOW 02 41 24 18 00 - ref : 02/0508 - 09/03 - Couleurs non contractuelles.
This document is our property. All reproduction rights are
reserved. In case of patent or registration of a model, all rights are
reserved.
This manual was made on basis of development of the fittings on the
issue date. Claims to its improper application shall not be taken into
account.
WARRANTY
The manufacturer declines all responsibility for malfunctioning and
damage caused to the fittings and the windows or doors equipped
with these fittings, resulting from the fittings not being fixed in accordance with the manufacturer’s instructions, from an improper use of
the fittings or defective maintenance or if the windows remain in opened position during a storm or strong winds.
For selected fittings our warranty will only apply if strict
machining, installation and compliance with the adaptation instructions have been fulfilled within the limit of the effective technical
recommendations included to this manual.
The warranty will be applied to products fitted in accordance with our
instructions and will not apply to products which are not manufactured or supplied by us.
Head Office : 25, rue Michel Couet, F-49160 LONGUÉ (France) - Phone : +33 2 41 53 21 00 - Fax : + 33 2 41 53 22 24
E-mail : comindustrie@bezault.com - Site Internet : www.bezault.com
Founded in year 1850, BEZAULT is an ASSA ABLOY Group company. With outstanding competences in design and innovation,
BEZAULT is the French leading company for the manufacturing of door and window equipments combining the most creative design
with the best performance. The company’s customer base includes the Building Industry and the Shipbuilding Industry.
The ASSA ABLOY Group is the world’s leading manufacturer and supplier of locks and assorted products
dedicated to satisfying end-user needs for security, safety and convenience.
DICAD 004 - October 2003