Machines and Tools for Pipe Working

Transcription

Machines and Tools for Pipe Working
2011/
2012
North America
Product Line
Innovative – professional – reliable
Manufacturer of Machines and Tools for Pipe Working
REMS – since 1909
Since its founding in 1909, REMS has been producing tools for pipe working,
particularly for sanitary and heating installation. First hand tools, later machines and
electric tools. REMS has always marketed products which have made the work of the
plumber easier, faster and cheaper. The number one priority of the founder Christian
Föll was always and still is today: „REMS must be better“. Today REMS is one of the
leading manufacturers of machines and tools for pipe working, and because of their
innovative engineering and their high quality REMS products are used and greatly
appreciated throughout the world.
REMS – Made in Germany
REMS products, described as „German Quality Product“, are manufactured in
Germany. The REMS manufacturing facilities are located in Waiblingen, near Stuttgart,
right in the centre of the German high-tech industry. Here extremely modern systems
and equipment are available for research and development, for production and quality
assurance. Add to this qualified employees, some of whom are already working in the
4th generation at REMS and have at their disposal the high level of special knowledge
and wealth of experience so essential to the manufacture of quality products.
Highly modern measuring and inspection
methods and trained experts guarantee
consistently high REMS quality.
In-house hardening department – an important
part of the know-how and the secret of REMS
quality tools.
REMS – exceptionally high safety standard
All REMS products comply with safety and accident prevention regulations and meet
corresponding European standards in accordance with the regulations of the EC
directives. The CE mark documents the conformity of the product with all requirements of all applicable EC directives. In addition to that – except a few manual tools
which are not relevant to safety – all REMS products are tested and approved by
independent testing institutes, e.g. TÜV. Therefore all REMS products fulfill a very
high standard of functional and operational safety.
REMS – market strength from a consistent product and sales policy
In addition to technically advanced and high quality products, the market strength of
REMS is based on its tight product line focussed on turnover and highly competitive
prices thanks to efficient in-house-manufacturing. The consistent sales policy rests on
long term projected results, confidence and predictability.
Headquarters in Waiblingen near Stuttgart
Manufacturing in Waiblingen near Stuttgart
REMS – at the peak of technical progress
New ideas, technical progress and REMS go together. This is underlined by many
valid national and international patents. REMS always succeeds in attaining the peak
of technical progress through innovative products. E.g. REMS Amigo, REMS Tiger,
REMS Curvo, REMS Power-Press, REMS Akku-Press – products which revolutionized
application technology.
The most important principle of the sales
policy is the sale of REMS products soley
through specialist dealers who are
supported in many ways. With well
equipped demonstration vans, the REMS
sales employees carry out product
training at the point of sale and
demonstrate REMS products at joint visits,
counter days and in-house
exhibitions. Moreover, REMS counts on an
excellent service network and REMS sales
subsidiaries in many countries.
REMS – guarantee of quality
REMS always regards the quality of its products as an important basis for customer
confidence. For REMS, quality is far more than just dimensional accuracy and
operation, and is based instead on a comprehensive quality assurance system which
commences even while demand from the market is being assessed, accompanies
the product during development and production, and is supplemented by systematic
quality analyses in the market.
While manufacturing and assembling REMS products, great demand is applied on
quality control ensuring a continuously high quality. Efficient CNC production centres
and modern measuring and inspection methods during the complete manufacturing
process and extensive quality checks during and at the end of the assembly process
guarantee a highly constant product quality. Moreover, the quality is regularly being
supervised and approved through testing institutes, who grant GS safety marks, during
plant checks.
2
REMS – online information system
The REMS online information system www.rems.de offers a large variety of
information on the REMS group of companies, the REMS products and how are
they being used and handled. Moreover the user finds the complete online-catalog
and detailed technical documentation, informations on latest exhibition dates and
addresses of authorized REMS service depots, down-load options of sales literature,
operating instructions, parts lists, product images and product videos, order options
for mailing sales literature in different languages, email addresses of REMS staff and
much more.
REMS eva – the die stock for professionals!
n Quality hand die stock n Excellent start-cutting and threading n Indestructible
REMS Amigo – the smallest, lightest, strongest and fastest
up to 1”!
REMS quality dies n Only one type of quick-change die heads
n Drive unit only 3.5 kg (7.7 lbs) n 1200 W (10.4 amps) with 30 % power increase
thanks to automatic carbon brush adjustment n Peak power input up to 1800 W
(2.45 HP) n Unique, patented support bracket n Maintenance-free gear n Robust,
powerful universal motor n Perfect, secure seating of quick-change die heads
n Good power supply and good oiling required n Thread pipe until it is flush with the dies
German
Quality Product
German
Quality Product
REMS Amigo Set. Electric die stock for pipe threads 1/8 –1”, bolt threads 6 –30 mm,
1/4 –1”.
REMS eva Set. Hand die stock for pipe threads
bolt threads 6–30 mm,
Ratchet lever, quick-change die heads. In sturdy steel case.
Art.-No. 520065
NPT 1/2”, 3/4”, 1”, 11/4”
Art.-No. 520067
NPT 1/2”, 3/4”, 1”, 11/4”, 11/2”, 2”
1/8 –2”,
1/4 –1”.
Quick-change die heads
For REMS eva, REMS Amigo, REMS Amigo 2, REMS Amigo 2 Compact and others
NPT 1/8”
Art.-No. 521200
NPT 1/4”
Art.-No. 521210
NPT 3/8”
Art.-No. 521220
NPT 1/2”
Art.-No. 521230
NPT 3/4”
Art.-No. 521240
NPT 1”
Art.-No. 521250
NPT 11/4”
Art.-No. 521260
NPT 11/2”
Art.-No. 521270
NPT 2”
Art.-No. 521280
Drive unit, support bracket, quick-change die heads. In sturdy steel case.
NPT 1/2”, 3/4”, 1”
Art.-No. 530024
REMS Amigo 2 Compact – the smallest and lightest up to 2”!
thanks to automatic carbon brush adjustment n Peak power input up to 1800 W
(2.45 HP) n Unique, patented support bracket n Maintenance-free gear n Robust,
powerful universal motor n Perfect, secure seating of quick-change die heads
Quick-change die heads for other threads and for left-hand threads available.
Ratchet lever
Art.-No. 522000
Quick-change die heads S –
the trouble shooter for hard to reach areas!
German
Quality Product
n e.g. caved wall, lay bare pipes, trench n Ideal for renovation and repair n Quickchange die heads S with specially mounted dies n Additional precise pipe guidance at
REMS Amigo 2 Compact Set. Electric die stock for pipe threads 1/8 – 2”, bolt threads
the cover side ensure perfect pipe centering and easy start-cutting n Extension of
6–30 mm, 1/4 –1”. Drive unit, support bracket, quick-change die heads.
ratchet drive REMS eva for threading in caved areas n Quick change die heads S fit
In sturdy steel case.
into the ratchet lever REMS eva and other suitable die stocks
NPT 1/2”, 3/4”, 1”, 11/4”
Art.-No. 540026
NPT 1/2”, 3/4”, 1”, 11/4”, 11/2”, 2”
Art.-No. 540027
REMS Amigo 2 – extremely strong up to 2”!
German Quality
Product
thanks to automatic carbon brush adjustment n Unique, patented support bracket
n Maintenance-free gear n Robust, powerful universal motor n Perfect, secure
seating of quick-change die heads
German
Quality Product
REMS die heads S Set. Quick-change die heads S, extension 300 mm.
NPT 1/2 - 3/4 - 1”
Art.-No. 520056
REMS Amigo 2 Set. Electric die stock for pipe threads 1/8 – 2”, bolt threads 6 –30 mm,
Die head S NPT 3/8”
Ratchet lever
Art.-No. 521226
Art.-No. 522000
1/4 –1”.
Drive unit, support bracket, quick-change die heads. In sturdy steel case.
NPT 1/2”, 3/4”, 1”, 11/4”, 11/2”, 2”
Dies for other threads available. Motors for other voltages available.
Art.-No. 540021
3
REMS 4” automatic die head
REMS REG St – effortless electric deburring!
n Excellent threads up to 4” thanks to 5 threading dies and stepless automatically
n Double edges for optimum chip flow n Drive through electric die stock with
opening die head n High cutting speed, no time consuming reverse n For automatic
octagonal seat, e.g. REMS Mini-Amigo, REMS Amigo, REMS Amigo 2,
lubrication and cooling n Electric drive through REMS Magnum, REMS Tornado,
REMS Amigo 2 Compact
REMS Amigo 2 and others
German Quality Product
German
Quality Product
REMS REG St 1/4 –2”. Inner pipe deburrer for electric operation. Steel pipes and others,
Ø 1/4 – 2”.
Art.-No. 731700
REMS 4”automatic die head. Threading attachment for pipe threads 21/2 –4”.
Dual purpose holder for threading and sawing with REMS Amigo, Amigo 2
Complete with chuck, gear, drive shaft, dies.
and REMS Tiger ANC
NPT 2 1/2 -3-4”
fits to REMS Magnum, REMS Tornado and others
NPT 2 1/2 -3-4”
Art.-No. 543100
Art.-No. 370011
Art.-No. 370013
REMS Herkules – the sturdy support!
n Easy movement of material in all directions during turning, pulling and pushing
fits to REMS Amigo 2
Make nipples yourself! Any length! Anywhere! Ideal tool for
working up short pipe pieces! Saves time and money!
REMS Nippelspanner
n To be used universally for threading machines and die stocks n Manual internal
German
Quality Product
clamping
German
Quality Product
REMS Nippelspanner
1/2”
Art.-No. 110100
3/4”
Art.-No. 110200
1”
Art.-No. 110300
11/4”
Art.-No. 110400
11/2”
Art.-No. 110500
2”
Art.-No. 110600
REMS Herkules. Vertically adjustable material support with roller guidance for rotating
and stationary pipe and solid material. Pipes Ø 1/8 – 4”, solid material Ø 6–115 mm.
REMS Herkules on tripod
Art.-No. 120100
The proper thread-cutting oil!
With high lubricating and cooling effect!
n Also well suited as a cooling lubricant for sawing metals
REMS Nippelfix
n Super fast and simple n For threading machines with opening die head n Automatic
quick-chuck n Production of nipples possible
German
Quality Products
German Quality
Product
REMS Spezial. High-alloyed mineral based thread-cutting oil. Can be washed out
REMS Nippelfix
with water, approved by experts.
1/2”
Art.-No. 111000
Can 5 l (1.32 Gal.)
Art.-No. 140100
3/4”
Art.-No. 111100
Can 10 l (2.64 Gal.)
Art.-No. 140101
1”
Art.-No. 111200
Spray 600 ml (21.2 oz.)
Art.-No. 140105
Squirt bottle 500 ml (17.6 oz.)
Art.-No. 140106
Larger sizes on request.
4
REMS Tornado – a class of its own!
n Only 1 universal automatic die head from 1/16 –2” for all threads n Automatic lubrication
REMS Magnum – the compact up to 2”!
n Only 1 universal automatic die head from 1/16 –2” for all threads n Automatic lubrica-
and cooling n Automatic chuck n Large oil basin and chip tray n Maintenance-free gear
tion and cooling n Proven quick-action hammer chuck n Large oil basin and chip tray
n Choice of 3 motors n Easy to carry, drive unit only 35 kg (77 lbs)
n Maintenance-free gear n Choice of 3 motors
Model
Magnum T
Model
Tornado T
Model
Magnum
Model
Tornado
Wheel stand
(accessory)
Wheel stand
(accessory)
German
Quality Products
Stand
(accessory)
German
Quality Products
REMS Magnum. Threading, cutting, deburring, nipple threading. Pipe threads 1/16 – 2”
(with REMS 4” automatic die head 21/2 –4”), bolt threads 6– 60 mm, 1/4 – 2”. Machine
REMS Tornado. Threading, cutting, deburring, nipple threading. Pipe threads
1/16 –2”
complete with dies NPT 1/2 – 3/4”, NPT 1–2”. Light version with removable large oil basin
and chip tray. For work bench, stand or wheel stand with material support.
complete with dies NPT 1/2– 3/4”, NPT 1–2”. Portable version with 3 tubular legs, with
2000 L-TUniversal motor 110 V, 50–60 Hz, 1700 W (2.31 HP).
removable large oil basin and chip tray.
2000 Universal motor 110 V, 50–60 Hz, 1700 W (2.31 HP).
2010 L-TPole-reversible capacitor motor 110 V, 60 Hz, 2100 W (2.85 HP). 30 rpm, also
53 rpm.
Art.-No. 340200
REMS Tornado T. Threading, cutting, deburring, nipple threading. Pipe threads 1/16 –2”
53 rpm
Art.-No. 340226
under full load. Very quiet running.Art.-No. 340227
REMS Magnum T. Threading, cutting, deburring, nipple threading. Pipe threads 1/16 –2”
(with REMS 4” automatic die head 21/2 – 4”), bolt threads 6– 60 mm, 1/4 – 2”. Machine
complete with dies NPT 1/2 – 3/4”, NPT 1–2”. Integrated, even larger oil basin and chip
complete with dies NPT 1/2– 3/4”, NPT 1–2”. Integrated, even larger oil basin and chip
tray. For work bench, stand or wheel stand with material support.
tray. For work bench, stand or wheel stand with material support.
2000 T
Universal motor 110 V, 50–60 Hz, 1700 W (2.31 HP).
2000 T
53 rpm
2010 T
Art.-No. 340206
Universal motor 110 V, 50–60 Hz, 1700 W (2.31 HP).
Art.-No. 340220
53 rpm.
Pole-reversible capacitor motor 110 V, 60 Hz,
2010 T
Pole-reversible capacitor motor 110 V, 60 Hz,
2100 W (2.85 HP). 30 rpm, also under full load.
Very quiet running.
2100 W (2.85 HP). 30 rpm, also under full load.
Art.-No. 340207
Very quiet running.
Stand
Art.-No. 344105
Stand
Art.-No. 344105
Wheel stand
Art.-No. 344100
Wheel stand
Art.-No. 344100
Art.-No. 340221
REMS Magnum – the super machine up to 3”!
available on special order
REMS Magnum – the super machine up to 4”!
n Only 1 universal automatic die head from 1/4 –2” and from 21/2 – 4” for all threads
n Exceptionally round and clean threads up to 4” by using 6 threading dies
n Automatic lubrication and cooling n Proven quick-action hammer chuck n Large oil
basin and chip tray n Maintenance-free gear
German
Quality Product
REMS Magnum T. Threading, cutting, deburring, nipple threading. Pipe threads 1/4 –4”,
bolt threads 14– 60 mm, 1/2 – 2”. Machine complete with dies for NPT pipe threads.
Integrated, even larger oil basin and chip tray. For work bench, stand or wheel stand
with material support.
Wheel stand
(accessory)
Choice of 3 powerful motors:
Universal motor
4000 T
Universal motor 110 V, 50–60 Hz, 1700 W (2.31 HP). 23 rpm.
Equipment 21/2 – 4”
Art.-No. 380426
Art.-No. 380429
4020 T
Pole-reversible 3 phase motor 220 V, 60 Hz, 2000 W (2.72 HP).
24/12 rpm, also under full load. Very quiet running.
Art.-No. 380428
Art.-No. 380431
Stand
Art.-No. 344105
Wheel stand
Art.-No. 344100
Capacitor motor
3-phase motor (on request)
5
REMS Unimat 75 – the high-performance machine for bolt
threads up to 72 mm, 2¾”, for pipe threads up to 2½”!
n High efficiency n Only one universal automatic die head for all threads, automatic
opening and closing n For numerous type of threads, also left-hand threads and fine
threads n Tangential-chaser-threading-system n Large threading range n Fast working,
short resetting time n For single and series production n Low hourly rate for the machine
REMS roll grooving attachment – compact – universal!
n Proven REMS grooving rollers with perfectly size-adjusted pressure rollers and
counterpressure rollers with well gripping axial knurls guarantee a secure rotation of the
pipe and a precise grooving n Grooving rollers easily interchangeable n Built-in ring
gauge for pre-setting of groove depth n Only one roll grooving attachment for REMS
Magnum and REMS Tornado
n Simple operation. Relieves expensive turning machines and specialists
German
Quality Product
German
Quality Product
REMS roll grooving attachment. Grooving pipes of pipe coupling systems
1–6” (sched. 40), 8–12” (sched. 20). Complete with hydraulic hand pump and 1 set
of 2–6” grooving rollers (pressure roller, counterpressure roller).
Grooving attachment
Art.-No. 347000
fits to REMS Magnum and REMS Tornado
Grooving attachment R 300
Art.-No. 347001
fits to Ridgid Model 300
Grooving attachment R 535
Art.-No. 347002
fits to Ridgid Model 535
Grooving attachments for other machines on request.
REMS Unimat 75. Semi-automatic threading machine. Bolt threads 6– 72 mm,
1/4 – 2 3/4 ”,
pipe threads 1/16 –2 1/2”. Tolerance class according to DIN 13 „medium“ (6 g). Thread
length up to Ø 30 mm unlimited, above Ø 30 mm up to 200 mm. Machine complete.
Without threading sets, without closing lever.
With manual clamping device
Art.-No. 750003
With hydraulic/pneumatic clamping device
Art.-No. 750004
Chasers for many threads available. Ask for detailed technical information „REMS Unimat“.
REMS Unimat 77 – the high-performance machine for pipe
threads up to 4”!
Grooving rollers 1–11/2”(set)
Grooving rollers 2–6”
(set)
Grooving rollers 8–12”
(set)
Grooving rollers Cu 2–6” (set)
Grooving rollers for stainless steel on request.
Art.-No. 347030
Art.-No. 347035
Art.-No. 347040
Art.-No. 347034
REMS Magnum RG – the compact up to 12”!
n Proven REMS grooving rollers with perfectly size-adjusted pressure rollers and
counterpressure rollers with well gripping axial knurls guarantee a secure rotation of the
pipe and a precise grooving n Grooving rollers easily interchangeable n Built-in ring
gauge for pre-setting of groove depth n Maintenance-free gear n Choice of 3 motors
n Portable light version n Conversion kit for threading as accessory
n Only one universal automatic die head for all pipe threads, automatic opening and
closing n Tangential-chaser-threading-system n Large threading range n Fast working,
short resetting time n For single and series production
German
Quality Product
Wheel stand
(accessory)
German
Quality Product
REMS Magnum RG. Roll grooving machine for grooving pipes of pipe coupling systems
1–6” (sched. 40), 8–12” (sched. 20). Machine complete with REMS roll grooving
attachment and 1 set of 2–6” grooving rollers (pressure roller, counterpressure roller).
For work bench, stand or wheel stand with material support.
2000 RG-T Universal motor 110 V, 50–60 Hz, 1700 W (2.31 HP). 53 rpm.
Art.-No. 340230
2010 RG-T Pole-reversible capacitor motor 110 V, 60 Hz, 2100 W (2.85 HP).
30 rpm, also under full load. Very quiet running.
Art.-No. 340231
REMS Unimat 77. Semi-automatic threading machine. Pipe threads 1/4 –4”. Thread length
up to 120 mm. Machine complete. Without threading sets, without closing lever.
With manual clamping device
Art.-No. 770003
With hydraulic/pneumatic clamping device
Art.-No. 770004
Stand
Wheel stand Conversion kit Magnum RG-T to L-T for threading
Art.-No. 344105
Art.-No. 344100
Art.-No. 340110
Chasers for many threads available. Ask for detailed technical information „REMS Unimat“.
6
Choice of
3 powerful motors:
Universal motor
Capacitor motor
3-phase motor
Saws of the New Generation
n reduced friction and wear
n substantially reduced heat generation
n for extremely long service life,
also during tough use
up to 6”, 160 (250) mm
...in confined areas also
e.g. 2” steel pipe in only 8 s !
Patents make the REMS reciprocating saws unique:
Universal patented saw blade clamp for holding all saw blades – with universal or
double tang – without changing or turning the saw blade thrust piece.
REMS Powersaw ANC. Electric reciprocating saw for right angle sawing. Steel pipes
and others up to 6”, 160 mm. Complete with guide support up to 2” and 2 REMS special
saw blades up to 2”. In sturdy steel case.
Art.-No. 560020
Sturdy, square lift rod, mounted precisely in needle bearings, prevents deflection of
bearing and guarantees a long service life.
Unique patented guide support and special saw blade for right angle cuts and super
fast sawing up to 4”.
REMS Powersaw ANC VE. Electric reciprocating saw with Vario-Electronic (VE) for
right angle sawing. Steel pipes and others up to 6”, 160 mm. With D-shape handle and
electronic stepless speed control (acceleration switch). Complete with guide support up
to 2” and 2 REMS special saw blades up to 2”.
In sturdy steel case. Art.-No. 560027
REMS Powersaw ANC – the saw for the pipe fitter!
n Easy sawing, rapid, effortless n Only 3.0 kg (6.6 lbs) n Unique, patented guide
support and special saw blades for right angle cuts. Essential for professional pipe
installation n Powerful universal motor 110 V, 50–60 Hz, 1050 W (10.4 amps)
n Sturdy, square lift rod prevents deflection of bearing and guarantees a long service
life n Aggressive orbital action n Long service life of saw blades n Universal
patented saw blade clamp. All saw blades – with universal or with double tang – can
be clamped without changing or turning the saw blade thrust piece
REMS Powersaw ANC SR. Electric reciprocating saw for right angle sawing. Steel
pipes and others up to 6”, 160 mm. With stepless electronic speed control with sensitive
start-sawing, speed generator, temperature control and stall protection 1400 W
(12.78 amps). Complete with guide support up to 2” and 2 REMS special saw blades
up to 2”. In sturdy steel case.
REMS guide support up to 4”
Motors for other voltages available.
Art.-No. 560026
Art.-No. 563100
7
REMS Powersaw ANC pneumatic – for sawing in dangerous
environment!
n Weighs only 3.8 kg (8.4 lbs) n Powerful pneumatic motor, 1000 W (1.36 HP), operating
pressure 6 bar (85 psi), air consumption 1.6 m³/min (56 cf/min) n Other description see
REMS pack of 5 saw blades – German Quality Products –
For REMS Powersaw, REMS Panther, REMS Cat and others
1.For REMS Powersaw
HSS-Bi
REMS Powersaw ANC
REMS special saw blade –
Absolutely essential for right angle sawing with guide support
REMS special saw blade
REMS Powersaw ANC pneumatic. Pneumatic reciprocating pipe saw for right angle
Thinner wall steel pipes
up to 2”
Art.-No. 561007
Steel pipes up to 2” Art.-No. 561001
Steel pipes up to 4” Art.-No. 561002
sawing. Steel pipes and others up to 6”, 160 mm. Complete with guide support up to 2”
and 2 REMS special saw blades up to 2”.
2.For REMS Panther/REMS Cat/REMS Powersaw
Art.-No. 560022
HSS-Bi
REMS Panther ANC VE – super small, super light, super handy!
n Robust, job site-proven n Super small, handy design. Only 12.6” long n Super light,
only 2.4 kg (5.3 lbs) n For sawing metal, boilers, tanks, bath tubs, window frames and
much more n Powerful universal motor 110 V, 50–60 Hz, 500 W (4.5 amps) n Square
lift rod prevents deflection of bearing and guarantees a long service life n Aggressive
orbital action n With Vario-Electronic n Long service life of saw blades n Universal
saw blade clamp. All saw blades – with universal or with double tang – can be
clamped without changing or turning the saw blade thrust piece
REMS universal saw blade –
with combo-toothing, flexible, for free-hand sawing. Instead of many different
saw blades.
German Quality
Product
Art.-No. 561006
REMS universal saw blade
100 mm long, 4”
150 mm long, 6”
Art.-No. 561005
200 mm long, 8”
Art.-No. 561003
300 mm long,12”
Art.-No. 561004
3.For REMS Panther/REMS Cat/REMS Powersaw
and other makes
HSS-Bi
REMS Panther ANC VE. Universal electric reciprocating saw with Vario-Electronic (VE)
for free-hand sawing. Steel pipes and others up to 6”, 160 mm. Complete with 1 REMS
universal saw blade 150 mm. In cardboard box.Art.-No. 560025
Carrying bag
Art.-No. 574436
HSS-Bi
REMS Cat ANC VE – saws anything, anywhere!
HSS-Bi
n Extremely versatile and powerful n Only 3.0 kg (9.5 amps) n For sawing metal,
boilers, tanks, bath tubs, window frames and much more n Powerful universal motor
110 V, 50 – 60 Hz, 1050 W (1.43 HP) n Square lift rod prevents deflection of bearing
and guarantees a long service life n Aggressive orbital action n With Vario-Electronic
n Long service life of saw blades n Universal saw blade clamp. All saw blades – with
universal or with double tang – can be clamped without changing or turning the saw
blade thrust piece
HSS-Bi
REMS saw blades – for different purposes
German Quality
Product
REMS Cat ANC VE. Universal electric reciprocating saw with Vario-Electronic (VE) for
free-hand sawing. Steel pipes and others up to 6”, 160 mm. Complete with 1 REMS
universal saw blade 150 mm.
In cardboard box.
Art.-No. 560030
In steel case.
Art.-No. 560040
8
Metals 3 mm and thicker
REMS saw blade
REMS saw blade
REMS saw blade
100 mm long, 4” Art.-No. 561101
150 mm long, 6” Art.-No. 561103
200 mm long, 8” Art.-No. 561102
Metals 1–3 mm
REMS saw blade
150 mm long, 6” Art.-No. 561104
Metals 1–3 mm (for curved cuts)
REMS saw blade
90 mm long,3.5” Art.-No. 561107
Metals 4 mm and thicker, wood with nails, pallets
REMS saw blade
150 mm long, 6” Art.-No. 561110
All types of wood
REMS saw blade
300 mm long, 12” Art.-No. 561111
Plasterboards, breeze blocks etc.
REMS saw blade
150 mm long, 6” Art.-No. 561115
REMS Nano – Cutting up to 1⅝”. Ultra-light. Fast.
REMS Turbo Cu-INOX – burr-reduced, right angle, rapid!
n Portable circular pipe sawing machine n Burr-reduced sawing through double
clamping vice n Saws without lubricant. Ideal for stainless steel tubes and copper
tubes of pressfitting systems n Proven universal motor, 110 V, 50–60 Hz, 500 W
(0.68 HP) n Maintenance-free gear n Powerful, e.g. Ø 7/8” in only 4 s n Compact,
easy to transport, only 17 kg (37 lbs)
n Mobile, electric tube cutting machine for fast, right angled cutting without outer burr
n Handy and light, only 1.9 kg (4.2 lbs) n Strong, torsion-free aluminium structure for
right angled cutting n Easy cutting of the tubes by specially designed cutter wheel
n Proven DC motor 110 V, 200 W (0.27 HP). Powerful. e.g. copper tube Ø ⅞” in only
3 s. Ideal speed 130 rpm for optimum cutting
German
Quality Product
REMS Turbo Cu-INOX. Circular pipe saw with universal double clamping vice for
burr-reduced, right angle, rapid sawing up to Ø 76 mm. Without saw blade.
Art.-No. 849006
Circular saw blade HSS, fine-toothing,
225 x 2x 32, 220 teeth
Art.-No. 849703
Circular saw blade HSS-E (cobalt alloyed),
fine-toothing, 225 x2 x 32, 220 teeth.
Very long service life.
Art.-No. 849706
REMS Nano Basic-Pack. Electric tube cutting machine for fast, right angled cutting of
pipes Ø 10–40 mm, ½–1⅝”, without outer burr. For tubes of the press fitting systems
made of stainless steel, C-steel, Ø 12–28 mm, ½–1⅛”, copper Ø 10–35 mm, ½–1⅜”.
Multilayer composite tubes Ø 10–40 mm, ½–1⅝”. With maintenance-free gear, proven
DC motor 110 V, 50–60 Hz, 200 W (0.27 HP). Speed 130 rpm. Back pressure rollers
made of hardened precision steel. Safety switch Without cutter wheel. In carrying bag.
Art.-No. 844010
REMS Akku-Nano – Cutting up to 1⅝”. Ultra-light. Fast.
REMS Turbo K – the most powerful in its class!
n Compact, easy to carry, only 22 kg (48 lbs) n Universal vice with length stop
n Robust, maintenance-free gear n Proven universal motor, 110 V, 50–60 Hz, 1200 W
n Mobile, battery-powered tube cutting machine for fast, right angled cutting without
outer burr n Handy and light, only 2.1 kg (4.6 lbs) n Strong, torsion-free aluminium
structure for right angled cutting n Easy cutting of the tubes by specially designed
cutter wheel n Powerful Li-Ion 10.8 V battery with 1.3 Ah capacity for extremely long
life and high cutting performance, with great power reserve, e.g. copper tube Ø ⅞” in
only 3 s. Ideal speed 130 rpm for optimum cutting
n Ideal speed (115 rpm) for fast, smooth sawing n Powerful, e.g. 2” steel pipe in only 5 s
<)
90° ±
78 55 70x5050x50 40 40
50 x 30
45° ² 60 55 60x4050x50 40 40
50 x 30
NEW
German
Quality Product
REMS Turbo K. Universal circular metal sawing machine with automatic cooling lubricant
unit for straight cuts and bevel cuts up to 45°. Complete with 1 filling of REMS cooling
lubricant. Without saw blade. Art.-No. 849007
Universal circular saw blade HSS,
225×2×32, 120 teeth
Art.-No. 849700
Circular saw blade HSS, fine-toothing,
225×2×32, 220 teeth
Art.-No. 849703
Circular saw blade HSS-E (cobalt alloyed), fine-toothing,
225×2×32, 220 teeth. Very long service life.
REMS Akku-Nano Basic-Pack. Electric tube cutting machine for fast, right angled
cutting of pipes Ø 10–40 mm, ½–1⅝”, without outer burr. For tubes of the press fitting
systems made of stainless steel, C-steel, Ø 12–28 mm, ½–1⅛”, copper Ø 10–35 mm,
½–1⅜”. Multilayer composite tubes Ø 10–40 mm, ½–1⅝”. With maintenance-free gear,
powerful battery motor 10,8 V, 270 W. Speed 130 rpm. Safety switch. Battery Li-Ion
10.8 V, 1.3 Ah, rapid charger Li-Ion 230 V, 50–60 Hz, 65 W. Counter pressures rollers
made of hardened precision steel. Single open ended wrench size 8. Without cutting
wheel. In carrying bag.
Art.-No. 844011
Art.-No. 849706
REMS cutter wheel Cu-INOX for stainless steel pipes
of pressfitting systems, copper, C-steel
Art.-No. 844050
REMS cutter wheel V
for multilayer composite pipes Art.-No. 844051
9
REMS Cento – Cutting up to 4”. Fast, dry. No outer burr.
n Light, compact machine for pipe cutting n Ideal for stainless steel and copper
tubes of pressfitting systems n Super light and handy, only 15 kg (33 lbs) n Stable,
distortion-free cast construction for right angled cutting n Powered cutter wheel and
linear advance for fast cutting (Patent DE 10 2005 053 179) n Power saving feed-in
through easy to grip, proven advance-lever and machine screw spindle n Robust
gear, precisely mounted in roller and needle bearings, maintenance-free n Proven
universal motor, 1200 W (1.63 HP). Powerful, e.g. stainless steel pipe Ø 2” in just 4 s
n Safety foot-switch with emergency stop n REMS special cutter wheels – Specially
hardened, from proven, through-hardened REMS die-steel, ensuring long service life
REMS RAS – quality pipe cutters for high demands!
n Solid body, robust spindle, long spindle guidance, hardened back pressure rollers
and precise cutter wheel bearing on a hardened, non rotating wheel shaft guarantees
an exact alignment to the pipe and a long service life n Cutter wheel protected against
touching the back pressure rollers by infeed limitation
REMS RAS St. Pipe cutter for steel pipes Ø 1/8 –4”, 10–115 mm.
St 1/8 –2”s ≤ 8 mm
Art.-No. 113000
St 11/4 –4”s ≤ 8 mm
Art.-No. 113100
German Quality
Product
International
Design
Award
Patent DE 10 2005 053 179
REMS Cento. Pipe cutting machine for fast, right angled, cutting of pipes with no outer
burr Ø 8–108 mm, 1/4 – 4”. For stainless steel tubes of pressfitting systems, copper
pipes. For steel pipes, plastic pipes, multilayer composite pipes. With maintenance-free
gear, proven universal motor 110 V, 50–60 Hz, 1200 W (1.63 HP). Speed 115 rpm.
Rollers in hardened precision steel pipe. Safety foot-switch. Ring spanner.
Without cutter wheel.
Art.-No. 845001
REMS cutter wheel Cu-INOX, wall thickness s ≤ 4 mm,
for stainless steel tubes of pressfitting
systems, copper
Art.-No. 845050
REMS cutter wheel Cu, wall thickness s ≤ 4 mm, for copper
tubes of pressfitting systems, copper Art.-No. 845053
REMS cutter wheel St, wall thickness s ≤ 8 mm,
for steel pipes
Art.-No. 845052
One and the same wheel
(Art.-No. 113210 or 113225)
for all REMS tubing cutters!
REMS RAS Cu-INOX. Tubing cutter for copper tube, stainless steel tubes, steel tubes,
aluminium tubes, brass tubes, Ø 3–120 mm, 1/8 –4”.
Art.-No. 113200
Cu-INOX 3–16, 1/8 – 5/8”s ≤ 4 mm
Art.-No. 113240
Cu-INOX 3–28 Mini, 1/8 –11/8”s ≤ 4 mm
Art.-No. 113300
Cu-INOX 3–28, 1/8 –11/8”s ≤ 4 mm
Art.-No. 113350
Cu-INOX 3–35, 1/8 –13/8”s ≤ 4 mm
Art.-No. 113380
Cu-INOX 6–42, 1/4 –15/8”s ≤ 4 mm
Art.-No. 113400
Cu-INOX 6–64, 1/4 –21/2”s ≤ 4 mm
s ≤ 4 mm
Art.-No. 113500
Cu-INOX 64–120, 21/2 –4”
REMS cutter wheel V, wall thickness s ≤ 7 mm,
for plastic and multilayer composite pipes Art.-No. 845051
l
rp whee
with sha
REMS cutter wheel C-SF for cutting carbon steel pipes whilst
simultaneously creating a welding chamfer Art.-No. 845055
Rollers INOX (set) for stainless steel pipes Art.-No. 845110
Stand (Cento, Turbo)
Art.-No. 849315
REMS Akku-ROS P 40 – fast, easy cutting of pipes. Powerful,
e. g. Ø ⅝” multilayer composite tubes in only 4 s.
REMS RAS Cu. Tubing cutter for copper tube, Ø 3–42 mm, 1/8 –13/4”.
Cu 3–35, 1/8 –13/8”s ≤ 3 mm
Art.-No. 113340
Cu 3–42, 1/8 –15/8”s ≤ 3 mm
Art.-No. 113320
Up to 200 cut sections per battery charge!
NEW
Specially designed for
stainless steel tubes
e
k releas
with quic
eel
h
w
rp
a
and sh
REMS RAS Cu. Tubing cutter for copper tube, Ø 8–64 mm, 3/8 –21/2”.
Cu 8–42, 3/8 –15/8”s ≤ 3 mm
Art.-No. 113370
Cu 8–64, 3/8 –21/2”s ≤ 3 mm
Art.-No. 113410
Only 2.6 lbs!
International
Design Award
Wedge-shaped blade for universal cutting
of plastic and multilayer composite tubes
REMS Akku-ROS P 40 Set. Cordless pipe shears for fast, easy cutting of plastic and
multilayer composite tubes Ø ≤ 40 mm, Ø ≤ 1⅝”, s ≤ 6.7 mm. Electrical drive with
powerful 9.6 V, 70 W battery motor, maintenance-free gear, safety switch, on/off
switch. NiMH 9.6 V, 1.0 Ah battery, NiMH 100 – 240 V, 50 – 60 Hz, 6 W battery charger.
With wedge-shaped blade. In a box.
Art. No. 291310
10
REMS RAS P. Pipe cutter for plastic pipes, multi-layer composite tubes, Ø 10–160 mm,
1/2 –6”.
Art.-No. 290050
P 10–40, 1/2 –15/8”s ≤ 7 mm
Art.-No. 290000
P 10–63, 1/2 –2”s ≤ 7 mm
P 50–110, 2–4”s ≤ 11 mm
Art.-No. 290100
P 110–160, 4–6”s ≤ 16 mm
Art.-No. 290200
REMS cutter wheels – for extremely long service life!
REMS RAG – chamfering at 15°!
n German Quality Product n Specially hardened, in approved, tough-hard REMS die
n Pipe diameter and wall thickness steplessly adjustable n Also for deburring at plastic
steel quality n Extremely long service life
sleeve welding n Replacable
chamfering blades
US-Patent 5,641,253
REMS cutter wheels
St 1/8 –4”
s ≤ 8 mm
Art.-No. 341614
for REMS RAS St 1/8 –2”, 11/4 –4”
St 1–4”s ≤ 12 mm
Art.-No. 381622
for REMS RAS St 11/4 –4”
Cu 3–120s ≤ 3 mm
Art.-No. 113225
for RAS Cu 3-35, 3-42, 8-42, 8-64
Cu-INOX 3–120s ≤ 4 mm
Art.-No. 113210
for RAS Cu-INOX 3-16, 3-28, 3-35,
6-42, 6-64, 64-120
Cu-INOX b 3s ≤ 4 mm
Art.-No. 113220
for tubing cutters of other makes, e.g. Ridgid
P 10–63s ≤ 7 mm
Art.-No. 290016
for REMS RAS P 10-40, 10-63
P 50–315s ≤ 11 mm
Art.-No. 290116
for REMS RAS P 50-110, 110-160, 180-315
P 50–315s ≤ 16 mm
Art.-No. 290216
for REMS RAS P 50-110, 110-160, 180-315
P 50–315s ≤ 19 mm
Art.-No. 290316
for REMS RAS P 50-110, 110-160, 180-315
German
Quality Product
REMS RAG P. Pipe chamfering tools for external chamfering (15°) of plastic pipes
Ø 16–250 mm, 3/4 –10”, wall thickness ≤ PN 16
P 16–110
Art.-No. 292110
P 32–250
Art.-No. 292210
REMS REG Universal – the all purpose deburrer!
n Robust metal design for tough use n Rotating universal deburrer blade in handle
accomodates to the work piece edge to be deburred n Fast, simple blade replacement
REMS cutter wheels also fit into pipe/tubing cutters of other makes!
Ask for cutter wheel table!
REMS ROS – quality shears for clean, fast pipe cutting!
n Robust steel design n Easy cutting through special ratchet feed n Right angle,
burr-free cut through two-point pipe support and guided blade on both sides n Specially
hardened blade, replaceable
REMS REG Universal. Universal deburrer for deburring copper, steel, brass,
Art.-No. 113910
aluminium and plastic.
Replacement blade
REMS ROS P. Pipe shear for plastic pipes. Ideal for PVC.
P 42 P
Ø ≤ 42 mm, 1 5/8”
Art.-No. 291000 RP
P 63 P
Ø ≤ 63 mm, 2”
Art.-No. 291270
Replacement blade for P 42 P
Art.-No. 291021
Art.-No. 291271
for P 63 P
Art.-No. 113360
REMS REG 3-35 – the sharp edge!
n Outer-inner tubing deburrer n 3 deburrer blades, specially hardened and ground
n Sturdy aluminium design n Right angle, burr-free cut through exact pipe support and
guided blade on both sides n Specially hardened blade, replacable
German
Quality Product
Automatic
REMS REG 3-35. Outer-inner tubing deburrer. Copper, brass, aluminium, steel tubes,
plastic pipes, Ø 3–35 mm, 1/8 –13/8”.
Art.-No. 113900
REMS REG 10-42 – by hand or electric!
n Specially for stainless steel tubes n Solid quality tool for high demand and versatile
use n Adapter for electric drive (accessory)
REMS ROS P. Pipe shears for plastic pipes, multi-layer composite tubes.
Not recommended for PVC.
P 35
Ø ≤ 35 mm, 13/8”
Art.-No. 291200
Art.-No. 291220
P 35 A Automatic
Ø ≤ 35 mm, 13/8”
Art.-No. 291250
P 42
Ø ≤ 42 mm, 15/8”
Art.-No. 291100
P 75
Ø ≤ 75 mm, 21/2”
Replacement blade
for P 35
for P 35 A
for P 42
for P 75
Art.-No. 291201
Art.-No. 291221
Art.-No. 291251
Art.-No. 291111
REMS REG 10-42. Outer-inner deburrer for manual or electric operation.
Stainless steel tubes, other steel tubes, copper, brass, aluminium tubes, plastic pipes,
Ø 10–42 mm, 1/2 –15/8”.
Art.-No. 113810
Adapter for use with electric screw driver (speed ≤ 300 rpm)
Art.-No. 113815
11
REMS REG 8-35/10-54 – the multiple edges!
REMS REG 10-54 E – also for electric drive!
REMS Push / REMS Push INOX – reliable pressure hold!
n Robust, job site-proven metal design n Corrosion resistant, powder coated or stain-
n Easy, effortless deburring through multiple blades which are specially hardened and
less steel reservoir for 12 l content n Wear resistant pressure piston in brass, Ø 30 mm
ground n Robust metal design for tough use n REMS REG 10-54 E also for electric
n Double valve system for reliable pressure built-up n High pumping capacity with long
drive by commercially available screw driver (speed < 300 rpm).
stroke, fine pressure adjustment with short stroke n Distortion resistant lever, doubles
as carrying handle n High pressure hose with
fabric ply prevents measurement errors
Also for
electric drive
REMS REG. Outer-inner pipe deburrer for manual operation. Stainless steel tubes,
other steel tubes, copper, brass, aluminium tubes, plastic pipes.
REG 8-35
Ø 8 – 35 mm, 3/8 – 13/8”
Art.-No. 113825
REG 10-54
Ø 10 – 54 mm, 1/2 – 21/8”
Art.-No. 113830
REG 10-54 E
Ø 10 – 54 mm, 1/2 – 21/8” Art.-No. 113835
REMS Push. Hand pressure testing pump for pressure and tightness testing of piping
systems and receptacles, p ≤ 60 bar, 860 psi. Complete with pressure gauge,
p ≤ 60 bar, 860 psi, 1.5 m (5 feet) high pressure hose with 1/2”-connector.
Art.-No. 115000
REMS Catch S – the pipe wrench for the professional!
n Chrom-vanadium-steel n All-steel, drop forged n S-shaped jaws for secure 3-point
grip n Hardened, highly wear resistant toothing
NEW
German
Quality Product
REMS Push INOX. As REMS Push but with 12 ltr stainless steel tank 1.5 m (5 feet),
high pressure hose with 1/2”-connector.
Art.-No. 115001
Fine scale pressure gauge p ≤ 16 bar, 230 psi
REMS Catch S. Swedish pattern wrench S, DIN 5234 – Form C.
S 1/2”
Clamping width
36 mm
Art.-No. 116000
S 1”
Clamping width
47 mm
Art.-No. 116005
S
11/2”
Clamping width
60 mm
Art.-No. 116010
S 2”
Clamping width
78 mm
Art.-No. 116015
S 3”
Clamping width
112 mm
Art.-No. 116020
REMS Catch W – the water pump pliers for the professional!
n Chrom-vanadium steel n All steel, drop forged n Hardened, highly wear resistant
Art.-No. 115045
REMS E-Push – electric charging and testing! Up to 60 bar!
n Electric pressure testing pump n Robust, compact, light n Weighs only 13 kg
(29 lbs), easy to carry n High power piston pump, self-sucking, running in a sealed oil
bath with wear reduced pressure piston in stainless steel n Proven, powerful
condensor motor, 1750 W (2.38 HP), very powerful and fast n High pumping capacity
of 7 l/min n Pressure and tightness testing up to 60 bar/870 psi n Pressure gauge,
damped by a filling with glycerine, p ≤ 60 bar, 870 psi n High-pressure hose with
fabric ply prevents measurement errors n Suction hose with suction filter
toothing n With box joint
German
Quality Product
REMS E-Push. Electric pressure testing pump for pressure and tightness tests of
piping systems and receptacles up to 60 bar/870 psi. Pump unit with capacitor motor
REMS Catch W. Water pump pliers, DIN ISO 8976.
1.5 m (5 feet) suction hose with 1/2”-connection, 1.5 m (5 feet) high-pressure
Pipes Ø ≤ 1”
W 240
Pipes Ø ≤ 11/4”Art.-No. 116055
hose with 1/2”-connection. In cardboard box.
W 300
Pipes Ø ≤ 11/2”Art.-No. 116060
Fine scale pressure gauge p ≤ 16 bar, 230 psi Art.-No. 115045
12
Art.-No. 116050
110 V, 60 Hz, 1750 W, with pressure gauge, p ≤ 60 bar/870 psi, self-sucking,
W 175
Art.-No. 115100
REMS Solar-Push – filling, flushing and venting in one action!
REMS Eskimo – freezing instead of draining!
n Super fast up to 2” n Refrigerant carbon dioxide with high refrigerating capacity to
NEW
–79°C (–110 F) n Direct flow of the refrigerant onto the pipe ensure extremely short
freezing times, e.g. 3/4” steel pipe in only 5 min n No adjustment. The correct amount of
refrigerant is automatically supplied n Very small, highly flexible, indestructible freeze
collars n Rapid assembly n For operating even in tight spots and nitches n Flexible,
buckling-resistant and fractureproof high-pressure hoses n Clamping screws cannot get
lost n Unbreakable brass injector n For use with CO2 dip tube cylinder n Without
n Self priming n High displacement n Ideal
draining water lines, sprinkler or hot water systems
for solar power systems, ground heat systems
and underfloor heating n Easy cleaning and
simple filling thanks to large opening in the
plastic container n Practical grip handles for
easy carrying of the plastic container
REMS Solar-Push K 60. Electric filling and flushing unit for fast, easy filling, flushing
and venting of closed systems. Transport volume ≤ 50 l/min (13.2 gallon/min), tank
volume 30 l (7.9 gallon). With centrifugal pump, temperature-resistant for continuous
load ≤ 60°C (140°F). Transport pressure ≤ 5 bar/0.5 MPa/73 psi. Condenser motor
REMS Eskimo Set. Pipe freezer for steel, copper, plastic pipes, multi-layer composite
tubes Ø 1/8 –2”, 10–60 mm. 10 pairs of freeze collars for the complete work range,
bottle connector with T-distributor, closing nut, 2 handle pieces with injector,
2 high-pressure hoses. In sturdy case. Art.-No. 130002
110 V, 860 W (1.2 HP). 2 pieces flexible, transparent PVC fabric hoses ½” T60,
each 3 m (10 ft.) long, temperature-resistant ≤ 60°C (140°F). In box.
Art. No. 115312
REMS Akku-Ex-Press Cu ACC – fast, easy electric expanding
up to Ø 1¾”!
REMS Ex-Press Cu – for making sockets yourself!
n 6-face mandrel for even and concentric expanding n Extra long segments result in
extra long sockets for perfect tube connections according to DVGW n Expander heads
with calibration neck, fit other makes as well
n Compact, handy electric tool for fast, easy expanding and calibration of pipes for pipe
installation without fittings n Li-Ion technology n Compact, handy, light. Drive unit with
battery only 2.3 kg (5 lbs) n Ergonomically shaped housing with recessed grip
n Conical expanding mandrel (conical angle 18°) for even concentric expanding
n Extra long sockets, spring-loaded return of mandrel n Powerful electro-hydraulic
drive with automatic return (ACC), with powerful battery motor 14.4 V
NEW
German
Quality Product
with automatic circuit control
and charging status check
REMS Akku-Ex-Press Cu ACC Basic-Pack. Cordless pipe expander for fast, easy
expanding and calibration of pipes. Soft copper pipes Ø ⅜–1¾”, s ≤ 1.5 mm, soft
aluminium pipes, soft precision steel pipes, Ø ⅜–1¾”, s ≤ 1.2 mm, soft stainless steel
pipes Ø ⅜–1¾”, s ≤ 1 mm. Electro-hydraulic drive with automatic retraction, with
powerful battery motor 14.4 V, 420 W, robust planetary gear, eccentric reciprocating
pump and compact high power hydraulic system. Safety tip switch. Battery Li-Ion
14,4 V, 2,2 Ah, rapid charger Li-Ion/Ni-Cd 110 V, 50 – 60 Hz, 65 W.
Without expander heads. In sturdy steel case.
Art. No. 575016
REMS Ex-Press Cu Set. Hand tube expander for tube installations without
fittings. Soft copper tubes Ø 8–42 mm, 3/8 –11/8”, s ≤ 1.5 mm, soft aluminium tubes, soft
precision steel tubes, Ø 8–42 mm, 3/8 –11/8”, s ≤ 1.2 mm, soft stainless steel tubes
Ø 8–42 mm, 3/8 –11/8”, s ≤ 1mm. Expander drive, expander heads. In sturdy steel case.
Art.-No. 150017
Set 3/8 - 1/2 - 5/8 - 3/4 - 7/8 -11/8 ”
Expander head Cu
⅜”
Art.-No. 150220
(fit expander drives of REMS Akku-Ex-Press
½”
Art.-No. 150225
Cu ACC and other makes also)
⅝”
Art.-No. 150230
¾”
Art.-No. 150235
⅞”
Art.-No. 150240
1”
Art.-No. 150245
1⅛”
Art.-No. 150250
13
REMS Hot Dog 2 – the smallest and most powerful
soldering pliers!
REMS Twist/Hurrican – for making T-branches and sockets
yourself!
n Only 0.7 kg (1.5 lbs) n Super fast soldering without flame, e.g. Ø 5/8” in only 15 s
n Only one universal drive unit, only 2 kg (4.4 lbs) n Maintenance-free gear n Proven
n Enormous heating capacity up to 800°C (1470 F) n For permanent use
universal motor 110 V, 50–60 Hz, 620 W (0.84 HP) n High torque at low speed, left
n No transformer required, directly connected to
and right-hand rotation n Drive unit with hexagon mount
a socket, 110 V, 50 – 60 Hz, 440 W (0.6 HP)
Make sockets
yourself!
Make T-branches yourself!
REMS Twist – Electric tube expander
n Without annealing, standard socket in just a few seconds, extra long n For each
REMS Hot Dog 2. Electric soldering pliers for soft soldering of copper tubes
Ø 10–28 mm, 3/8 –11/8”. Heating capacity 800°C (1470 F). Soldering pliers,
tube size with rotating mandrel for easy expanding and smooth operation n No setting
n Integrated clamping device provides safe support against torque in both directions
250 g REMS Lot Cu 3 and REMS Paste Cu 3, cleaning brush. In sturdy steel case with
Art.-No. 163020
fire retarding insert.
REMS Contact 2000 – the smallest, strongest and fastest unit of
its kind!
n Rated power = Soldering capacity = 2000 W! n Enormous heating capacity (900°C,
1650 F) n Super fast soldering without flame, e.g. Ø 5/8 ” in only 18 s n Ready to solder
any time, to be connected only to a socket, 110 V, 50–60 Hz, 2000 W (2.72 HP)
n Indifferent to temperature influences electric control of soldering current, control voltage
24 V n Prisma-electrodes ensure maximum use through favorable seat n Wide work
REMS Twist Set. Electric tube expander for cold-expanding of hard and soft copper
tubes, Ø 12–22 mm, 3/8 – 7/8”, s ≤ 1 mm (0.039”), for tube installations without fittings.
Drive unit, drive holder, lubricant, expander tools. In sturdy steel case.
Set 3/8-1/2-5/8-3/4-7/8
Art.-No. 156004
radius thanks to 4 m cable length
REMS Hurrican – Electric tube extractor
n Also on tubes already installed n Proven technology, precise drilling without punching,
drill depth-stop according to the size of T-branch n Special design of extractor tools
facilitate even and smooth material deformation without burrs and notches
REMS Hurrican Set. Electric tube extractor for producing T branches without fittings.
Hard and soft copper tubes Ø 10–22 mm, 3/8 – 7/8”, s ≤ 1.5 mm (0.059”). Drive unit,
drive holder, tool holder, drill head, dimpling pliers, lubricant, extractor tools.
Set 3/8-1/2-5/8-3/4-7/8
Art.-No. 151002
REMS Twist/Hurrican – Electric tube expander and extractor
n Room and weight saving combination of REMS Twist and REMS Hurrican
n Only one drive unit for expander and extractor tools
German
Quality Product
REMS Contact 2000. Electric soldering unit for soft soldering of copper tubes Ø 6–54 mm,
1/4 –21/8”.
Heating capacity 900°C (1650 F). Soldering unit with safety transformer,
soldering pliers with 4 m (13 ft) cable length, 2 pairs of prima-electrodes. In cardboard box.
Art.-No. 164011
Prisma-electrodes (pair)
Art.-No. 164111
REMS Twist/Hurrican Combi Set. Electric tube expander and extractor. Drive unit,
Prisma-electrodes with holder (pair)
Art.-No. 164110
drive holder, tool holder, drill head, dimpling pliers, lubricant, expander tools, extractor
Rod-electrodes (pair)
Art.-No. 164115
tools. In sturdy steel case.
Steel case Art.-No. 164250
Set 3/8-1/2-5/8-3/4-7/8
14
Other voltages available.
Art.-No. 156014
REMS Swing – bending tubes where they are installed!
REMS Curvo – wrinkle-free bending!
n Fast operation through patented quick-acting feed forward and release n Universal
n Universal for many pipes and tubes n Compact, with integral absorbtion of torque
use for many tubes n Handy and light, only 1.3 kg (2.9 lbs) n Proven, reliable ratchet
during bending (US-Patent 5,056,347) n Super light, drive unit only 8 kg (17.6 lbs)
feed n Simple, fast operation, e.g. bends Ø 22 mm (7/8”) in only 9 s n Only 1 bender
n Can be used anywhere without previous setting n Fast and creep speed operation
drive for the complete work range up to Ø 32 mm n Marked bending formers for
for precise bending, e.g. 90° bends, Ø 7/8” in only 6 s. n Angle scale 0 to 180° n Rapid
exact bending n Bender recovered after a few bends through savings on fittings
change of bending and back formers n Only one type of bending and back formers for
REMS Curvo, REMS Curvo 50 and REMS Akku-Curvo n Maintenance-free gear with
safety slipping clutch n Universal motor 110 V, 50–60 Hz, 1000 W (1.36 HP) n Bender
recovered after a small number of bends through savings on fittings
US-Patent 5,056,347
German Quality
Product
for soft copper tubes
up to Ø 7/8” O.D.
for reverse bends
for copper tubes, also half hard or thin-wall, up to Ø 13/8” O.D.
for multi-layer composite
tubes up to Ø 32 mm, 11/4”
Up to Ø 32 mm, 11/4”!
REMS Curvo Set. Electric pipe bender Ø 10–40 mm, 3/8 –13/8”, up to 180°. Hard,
half-hard and soft tubes, also thin-walled, Ø 10–35 mm, 3/8 –13/8”, coated soft copper
tubes, also thin-walled, Ø 10–18 mm, stainless steel tubes of pressfitting systems
Ø 12–28 mm, 3/8 –11/8”, coated steel tubes of pressfitting system mapress C-STAHL
Ø 12–28 mm, soft precision steel tubes Ø 10–30 mm, steel pipes 1/4 – 3/4”, conduit DIN
EN 50086 Ø 16–32 mm, composite tubes Ø 14–40 mm, and others. Drive unit,
insert bolt. Bending formers and back formers. In sturdy steel case.
Set 3/8 - 1/2 - 5/8 - 3/4 - 7/8” O.D.
Art.-No. 580024
Basic-Pack (without bending and back formers) Art.-No. 580010
REMS Swing Set. Single-hand tube bender Ø 10 – 32 mm, 3/8 – 7/8”, up to 90°. Soft
Delivered with the smaller radius bending and back former. Additional bending and back
formers for other sizes and other bending radii available, see table on the right.
copper tubes Ø 10 – 22 mm, 3/8 – 7/8”, s ≤ 1 mm (0.039”), coated soft copper tubes
Ø 10 – 18 mm, 3/8 – 5/8”, s ≤1 mm, coated steel tubes of pressfitting system mapress
C-STAHL Ø 12– 18 mm, soft precision steel tubes Ø 10–18 mm, s ≤ 1mm, multi-layer
composite tubes Ø 14 – 32 mm. Up to Ø 26 mm with bender drive, bending formers,
universal crossbar with sliding pieces, in sturdy steel case. Up to Ø 32 mm with bender
drive, bending formers, 2 universal crossbars with sliding pieces, in sturdy case.
Set 3/8 - 1/2 - 5/8 - 3/4 - 7/8”
for soft copper tubes
Art.-No. 153021
Set 14 - 16 - 18 - 20 - 25/26 for multi-layer composite tubes
Art.-No. 153022
Set 16 - 18 - 20 - 25/26 - 32
for multi-layer composite tubes
Art.-No. 153023
Set Allround 32
3B
10-12-14-15-16-17-18-20-22-25/26-32
Art.-No. 153028
Device for reverse bends
on installed tubes
Art.-No. 153140
WB
Machine support 3B,
3/8 - 1/2 - 5/8 - 3/4 - 7/8”
height adjustable on tripod
Art.-No. 586100
Machine support WB,
height adjustable, for mounting on work bench
Art.-No. 586150
REMS bending spray, 400 ml (14.1 oz)
Art.-No. 140120
15
REMS Curvo 50 – wrinkle free bending of large pipes!
n Universal, compact electric tool for cold bending of pipes and tubes up to 50 mm,
1⅝”, up to 90° n All bending formers and back formers from REMS Curvo can be
used n Simple, effortless, fast working, e.g. 90° bends of steel pipe Ø 11/4” in 37 s.
Battery Li-Ion 18 V, 2,0 Ah
Art.-No. 565215
Rapid charger Li-Ion/Ni-Cd 110 V, 50–60 Hz, 65 W
Art.-No. 565220
US-Patent 5,056,347
Accessories for REMS Curvo, REMS Curvo 50 and REMS Akku-Curvo
Bending former and back former Ø 35 R100
Art.-No.
Art.-No.
Bending former and back former Ø 42 (15/8”) R140
Bending former and back former Ø 50 R135
Art.-No.
Bending former and back former IPS 1” (33.7 mm) R100 Art.-No.
Bending former and back former IPS 11/4” (42.4 mm) R140 Art.-No.
Adaptor block 10 – 40, Support 10 –40, 3/8 – 13/8”
for bending formers and back formers REMS Curvo
Art.-No.
581500
581510
581540
581520
581530
582120
REMS Akku-Curvo – wrinkle free bending. Cordless.
n Cordless tube bender up to 32 mm, 1⅛”, up to 180° n All bending formers and
back formers from REMS Curvo can be used n Compact, handy electric tool with
integral absorbtion of torque during bending (Patent US 5,056,347) n Super light,
drive machine with battery pack weights only 8.6 kg (19 lbs) n No setting. Simple,
effortless, fast working, e.g. 90° bend Ø ⅞” only 7 s n Powerful battery motor 18 V,
with large power reserve, 500 W (0.68 HP) output
NEW
US-Patent 5,056,347
German Quality
Product
REMS Akku-Curvo Set. Cordless tube bender Ø 10–32 mm, Ø 1/4 –11/8”, to 180°.
Hard, half-hard, soft copper pipes, also thin-walled, Ø 10 – 28 mm, Ø 3/8 – 11/8”, soft
jacketed copper pipes, also thin-walled, Ø 10 – 18 mm, pipes of the pressfitting
systems made of stainless steel Ø 12 – 28 mm, carbon steel, also coated
Ø 12–28 mm, soft precision steel pipes Ø 10–28 mm, steel pipes DIN EN 10255 Ø
1/4 – 1/2”, electrical installation pipes DIN EN 50086 Ø 16 – 25 mm, multilayer composite
tubes Ø 14–32 mm, among other things drive machine with D-shaped handle, maintenance-free gear with safely slipping clutch, powerful battery motor 18 V, stepless,
electronic safety switch with immediate stop, right and left-hand rotation. High power
battery Li-Ion 18 V, 2.6 Ah, rapid charger Li-Ion/Ni-Cd 110 V, 50 – 60 Hz, 65 W. Insert
bolt. Bending and back formers. In sturdy steel case.
Art.-No. 580074
Set 3/8 - 1/2 - 5/8 - 3/4 - 7/8”
Basic-Pack (without bending and back formers) Art.-No. 580012
Delivered with the smaller radius bending and back former. Additional bending and back
formers for other sizes and other bending radii available, see table on the right.
16
St 50086
St 10255
Bending
radius
St 2391–2394
mmArt.-No.
V
for tubes
Ø mm/inch O.D.
St 2394-U
Bending and
back former
St 2463
Suitable for
Cu-U
Cu
REMS Curvo 50 Basic-Pack. Electric pipe and tube bender Ø 10 – 50 mm, 3/8 –15/8”,
up to 90°. Steel pipes Ø 1/4 – 11/4”, hard, half-hard and soft copper tubes, Ø 10–42 mm,
3/8 –15/8”, stainless steel tubes of pressfitting systems Ø 12 – 42 mm, 3/8 – 15/8”, multilayer composite tubes Ø 14 – 50 mm and others. Drive unit with maintenance-free
gear and safety slipping clutch, u
niversal motor 110 V, 50 – 60 Hz, 1000 W (1.36 HP),
stepless electronic safety switch, right and left-hand rotation. Adaptor block 35–50,
Support 35–50, insert bolt. In sturdy steel case.
Art.-No. 580110
10
40 ••581400
12
45 • • •581410
14, 10 U, 1/4 (DN 6)
50 • • • • • 581420
15, 12 U
55 • • • •581430
16, 12 U
60 • • • • • 581440
17, 15 U
56 •• 581110
18, 14 U, 15 U, 3/8 (DN 10)
70 • • • • • 581450
20, 16 U, 18 U
75 • • • • • 581080
22, 18 U, 1/2 (DN 15)
77 • • • • • 581460
22, 18 U, 1/2 (DN 15)
88 • • • •581470
24, 22 U
75 • •581130
25
98 •• • • 581180
26
98• • 581270
28, 3/4 (DN 20)
1021) • • • • 581070
28, 3/4 (DN 20)
114 • • • • 581310
30, 28 U
98 • •581150
32
98• 581280
32114
•• • 581320
35140
•581350
40
140• 581330
3/8”
(9.5 mm)
43 / 1.69”
1/2”
(12.7 mm)
52 / 2.05”
5/8”
(15.9 mm)
63 / 2.48”
3/4”
(19.1 mm)
75 / 2.95”
7/8”
(22.2 mm)
98 / 3.86”
1”
(25.4 mm)
98 / 3.86”
1”
(25.4 mm)
101 / 3.98”
11/8”
11/4”
(28.6 mm)
(31.8 mm)
102 / 4.02”
114 / 4.48”
13/8”
(34.9 mm)
140 / 5.51”
•581200
•581210
•581220
•581230
•581240
•581250
•581370
•581260
•581320
•581350
1)
According to DVGW work sheet GW 392 minimum bending radius
of 114 mm required for copper tubes Ø 28 mm.
Cu:
hard, half-hard, soft copper tubes, also thin-wall
St 2463:
stainless steel tubes of pressfitting systems DIN 2463
St 2394-U: coated steel tubes of pressfitting systems mapress C-STAHL DIN 2394
St 10255:
steel pipes (thread pipes) DIN EN 10255 (DIN 2440)
St 2391-2394:soft precision steel tubes DIN 2391–2394
St 50086:
conduit DIN EN 50086
U:coated
V:
multi-layer composite tubes of pressfitting systems
REMS CamScope – Brilliant pictures and videos of cavities,
shafts and pipes. Documentation on MicroSD card.
Removable controller unit
for radio signal
transmission!
NEW
including
2 GB MicroSD card
Ø 9 mm or 16 mm
REMS CamScope Set 9-1. Mobile, handy endoscope camera with radio signal transmission for low cost inspection and damage analysis of places with difficult access
such as cavities, shafts, pipes etc. Documentation of photos and videos on MicroSD
card. Handheld unit with 4 batteries 1.5 V, AA, LR6. Removable controller unit with
radio signal transmission, 3.5” TFT-LCD colour display, MicroSD card slot, USB port,
video out socket PAL/NTSC, integrated Li-ion battery, 3.7 V, 1.2 Ah. 2 GB MicroSD
card. Camera cable set Color 9-1, consisting of colour camera Ø 9 mm with dimmable
white light LEDs and fixed focus function and 1 m formable push cable. Voltage
supply/charger Li-Ion 100 – 240 V, 50 – 60 Hz, 36 W, for controller unit. USB cable,
video cable. In sturdy case.
Art. No.-175111
900 mm (3 ft.) push cable extension
couplable up to a working length
of 4.5 m (15 ft.)
Art.-No. 175105
Camera cable set Color 16-1,
colour camera Ø 16 mm (0.63”)
with 1 m flexible push cable for the
inspection of narrow passages
n The date and time of the recording can be saved in the photo and video as an
option n Immediate playback of saved recordings or transmission to other devices
via MicroSD card n USB connector for direct connection to PC or laptop.
Art.-No. 175103
Camera cable set Color 9-1,
colour camera Ø 9 mm (0.35”)
with 1 m flexible push cable for the
inspection of very narrow passages Art.-No. 175104
REMS CamScope Set 16-1. Mobile, handy endoscope camera with radio signal transmission for low cost inspection and damage analysis of places with difficult access
such as cavities, shafts, pipes etc. Documentation of photos and videos on MicroSD
card. Handheld unit with 4 batteries 1.5 V, AA, LR6. Removable controller unit with
radio signal transmission, 3.5” TFT-LCD colour display, MicroSD card slot, USB port,
video out socket PAL/NTSC, integrated Li-Ion battery, 3.7 V, 1.2 Ah. 2 GB MicroSD
card. Camera cable set Color 16-1, consisting of colour camera Ø 16 mm with
dimmable white light LEDs and fixed focus function and 1 m formable push cable.
Add-on mirror, add-on hook, add-on magnet. Voltage supply/charger Li-Ion
100 – 240 V, 50 – 60 Hz, 36 W, for controller unit. USB cable, video cable.
In sturdy case.
Art.-No. 175110
17
REMS Orcus 3000 – brilliant color pictures in pipes and drains!
n Electronic camera inspection system for inexpensive inspection and damage
analysis n For pipes Ø 40 –150 mm, 11/2 – 6”, drains, ditches, chimneys and other
hollow spaces n Only one controller unit with a TFT color display for connecting
different sets of cables and camera heads for different requirements n Optional highresolution, special black & white camera or high-resolution special color camera
n 30 m (100 ft) push cable in a reel
REMS Orcus 3000 Basic
Controller unit in micro processing technology,
5.6” TFT-colour display, video connection PAL, in
sturdy, shock resistant plastic housing, splashproof. Voltage supply 110 V AC, 50-60 Hz, 15 W.
Art.-No. 173010
Exchangeable b/w camera head
with high resolution special b/w camera and
connection for push cable.
Art.-No. 173041
Exchangeable S-Color camera head
with high-resolution special color camera and
push cable.
Art.-No. 173042
Camera cable set Mini b/w
Particularly small camera head with special high
resolution black and white camera. 5 m (16 ft)
push cable, highly flexible, with connection for
b/w and color
in one unit!
controller unit. For small pipe dimensions and
tight pipe bends from Ø 40 mm, 11/2 ”.
Art.-No. 173200
Exchangeable cable set 30 H
30 m (100 ft) push cable with length marking; with
connections for controller unit and camera head.
On reel.
Art.-No. 173044
Centering guide Ø 62 mm (2.5”), pair
Art.-No. 173015
REMS Orcus 3000 Set. Electronic camera inspection system for inexpensive
inspection and damage analysis. For pipes Ø 40 – 150 mm, 11/2 – 6”, drains, ditches,
Centering guide Ø 100 mm (4”), pair
Art.-No. 173014
chimneys and other hollow spaces. Controller unit in micro processing technology,
5,6” TFT-colour display, in sturdy, shock resistant plastic housing, splash proof.
Voltage supply 110V AC, 50 – 60 Hz, 15 W. In sturdy carrying case. Choice of
exchangeable camera heads with high resolution special camera black and white or
Extension cable
Controller unit/camera-cable-set,
1.2 m (4 ft) long Art.-No. 173019
high resolution special colour camera. 30 m (100 ft) push cable with length marks in
pivoted cable carrier.
Set 30 b/w H
Exchangeable camera head with special
high resolution black and white camera.
30 m push cable with length marks.
In pivoted cable carrier.
Art. No. 173052
Protection cap with built-in mineral glass pane
Art.-No. 173126
Set 30 S- Color H Exchangeable camera head with special
high resolution colour camera.
30 m push cable with length marks.
In pivoted cable carrier.
18
Art. No. 173053
Voltage supply automobile 12 V,
5 m (16 ft) long
Art.-No. 173017
REMS Mini-Press ACC
Universal for all common pressfitting systems
Ø 10–40 mm / 3/8 –1¼”
n Universal, handy cordless tool with automatic circuit control for producing pipe
pressing joints for all common pressfitting systems n Super light and handy. Drive unit
with battery Li-Ion only 2.4 kg (5.3 lbs) n Optimum weight distribution for single-hand
operation n Ergonomically designed housing n Secure seating of pressing tongs by
automatic locking n Swivelling pressing tongs seat for REMS pressing tongs Mini
REMS pressing tongs Mini
n High-compression pressing tongs in forged and specially hardened steel n Pressing
contours of REMS pressing tongs are system-specific and correspond with the
respective pressfitting system. Thus perfect system-conformity, safe press jointing
n Pressing jaws of pressing tongs manufactured on CNC production centres ensure
high-precision machining of pressing contour. Hence far closer tolerances compared
to as cast pressing contour n Drive through REMS Mini-Press ACC drive unit
n Enormous thrust and pressing force for fast
System
and perfect press jointing
US
with automatic circuit control
U
and charging status check
UP
VUS
German
Quality Product
German Quality
Product
REMS Mini-Press ACC Basic-Pack. Cordless radial press with automatic circuit
control for producing pipe pressing joints Ø 10–40 mm, 3/8 – 1¼”. For operating with
REMS pressing tongs Mini. Swivelling pressing tongs seat with automatic locking.
Electro-hydraulic drive with powerful battery motor, robust planetary gear, eccentric
reciprocating pump and compact high power hydraulic system, safety tip switch.
Battery, rapid charger Li-Ion/Ni-Cd 110 V, 50 – 60 Hz, 65 W. In sturdy steel case.
REMS Mini-Press ACC Li-Ion Basic-Pack
battery motor 14.4 V, 420 W (0.57 HP), battery Li-Ion 14.4 V, 1.3 Ah Art.-No. 578012
Accessories for battery presses:
Battery Li-Ion 14.4 V, 1.3 Ah
Rapid charger 110 V, 50 – 60 Hz, 65 W
Art.-No. 571540
Art.-No. 571550
Art.-No. 571560
Pressing tongs Mini
Art.-No.
ASTM F 1807US 3/8”
578534
(Fittings withUS 1/2”
578536
Copper Crimp RingUS 3/4”
578538
for PEX tubing)
US 1”
578540
578566
Elkhart XPRESSTMVUS 1/2”
VUS 3/4”578568
VUS 1” 578570
VUS 1¼”
578606
578534
Hydro-Air Systems US 3/8”
578536
Hydro-PlumbUS 1/2”
578538
Plus PEXUS 3/4”
US 1”
578540
578374
Hydro-Air Systems
U 16 (1/2”)
578378
Hydro-Flex
U 20 (5/8”)
578380
PEX-AL-PEX
U 25 (3/4”)
U 32 (1”)
578382
578566
Legend-PressVUS 1/2”
578568
Press fitting systemVUS 3/4”
VUS 1” 578570
VUS 1¼”
578606
578566
NIBCO®VUS 1/2”
578568
Press SystemTMVUS 3/4”
VUS 1” 578570
VUS 1¼”
578606
Uponor MLC
UP 16 (1/2”) 578578
UP 20 (5/8”) 578582
UP 25 (3/4”) 578584
UP 32 (1”)
578586
578566
Viega ProPress®VUS 1/2”
578568
VUS 3/4”
VUS 1” 578570
VUS 1¼”
578606
578534
WATTS RADIANTUS 3/8”
578536
Watts WaterPEXUS 1/2”
578538
US 3/4”
US 1”
578540
578534
WATTS RADIANTUS 3/8”
578536
Watts RadiantPEXUS 1/2”
578538
US 3/4”
US 1”
578540
578374
WATTS RADIANT
U 16 (1/2”)
578378
Watts RadiantPEX-AL U 20 (5/8”)
578380
U 25 (3/4”)
U 32 (1”)
578382
578534
ZURN INDUSTRIESUS 3/8”
578536
ZURN PEXUS 1/2”
578538
US 3/4”
US 1”
578540
REMS pressing tongs Mini for other U.S. pressfitting systems on request.
REMS cropping tong Mini – cuts in just
2 seconds!
< 34 cm/13.4”
n Made of forged and specially hardened steel n Reversible
cropping inserts for double service life n Threaded rod can
be screwed into a threaded connection of the pipe clip or
the nut without rework after cutting n Driven by REMS
Mini-Press ACC n Patent US 7,284,330
REMS cropping tong Mini UNC ⅜”
Art.-No. 578623
REMS cropping insert UNC ⅜” (pair)
Art.-No. 571846
“mini” because:
Drive unit REMS Mini-Press ACC with pressing tongs installed has an ‘overall length’
of less than 34 cm/13.4”. Therefore crimping also possible in particularly tight areas.
German Quality
Product
19
REMS pressfitting tools
Ø 10–108 mm / 3/8 – 4”
n For secure crimping within seconds n Can be used anywhere, free-hand, over
head, in confined areas n Only one universal drive unit for operating with REMS
pressing tongs and pressing tongs/pressing chains of numerous other manufacturers/
suppliers n System-specific pressing tongs for all common pressfitting systems,
quickly interchangeable n Only one type of pressing tongs for all REMS radial
presses and suitable radial presses of other makes. All pressing tongs marked with *
fit into the REMS Eco-Press drive unit n Secure seating of pressing tongs by
automatic locking
Pressing contours
ACz
B
F
G
H
HA
HE
ZVSHK
RN
Confirmation of suitability
The suitability of crimping tools is determined basically by the manufacturer of
crimping tools. Moreover the suitability of REMS crimping tools has been confirmed
by the system manufacturer/supplier himself or approved through independent testing
institutes.
Confirmation of suitability through the system manufacturer/supplier
More than 90 % of the manufacturers/suppliers of the pressfitting systems listed herein
have tested REMS pressing tongs and confirmed the suitability for their pressfitting
system.
Confirmation of suitability through independent testing institutes
The suitability of REMS pressing tongs for additional pressfitting systems have been
confirmed through independent technical institutes:
TÜV-Certificates
Available for Geberit Mepla, Geberit Mapress C-STAHL, Geberit Mapress
EDELSTAHL, Geberit Mapress Kupfer, Nussbaum Cupress, Nussbaum Optipress,
Uponor Unipipe, Viega-’profipress’, Viega-’profipress G’, Viega-’sanfix P’, Viega’sanpress’, Viega-’Viegatherm P’, Wavin Tigris. The TÜV-certificates confirm that
REMS crimping tools are suitable for producing perfect and system-conformity
pressing joints corresponding to these systems, both in conjunction with REMS
pressing tongs and the pressing tongs of system manufacturers/suppliers.
REMS pressing tongs –
for all common pressfitting systems
KI
M
MT
RFz
SA
TH
U
UP
US
Select pressing tongs yourself!
Search for the required pressfitting system in the opposite table and select the correct
pressing tongs size. Please note that pressfitting systems for gas installation may only
be pressed with the pressing tongs/pressing rings which are highlighted in yellow in
the table. Intermediate tongs are necessary for driving the REMS pressing rings (PR).
High-compression pressing tongs in forged and specially hardened steel. Pressing
contours of REMS pressing tongs are system-specific and correspond with the
respective pressfitting system. Thus perfect system-conformity, safe press jointing.
Pressing jaws of pressing tongs manufactured on CNC production centres ensure
high-precision machining of pressing contour. Hence far closer tolerances compared
to as cast pressing contour.
Drive through all REMS radial presses (except REMS Mini-Press ACC) and suitable
radial presses of other makes. All pressing tongs marked with * have an optional
connection (Patent US 6,739,172) for manual drive through the radial press REMS
Eco-Press.
20
V
VP
VX
VUS
In Europe, REMS delivers pressing tongs for
over 200 pressfitting systems.
Application of REMS tools for pressfitting systems: Date 15.10.2010. REMS pressing tongs for other pressfitting systems on request.
Patent US 6,739,172
ASTM F 1807
System
Pressing tongs
ASTM F 1807US 3/8” *
(Fittings with
US 1/2” *
Copper Crimp Ring
US 3/4” *
for PEX tubing)
US 1” *
US 1¼” Elkhart XPRESSTMVUS 1/2”
VUS 3/4”
VUS 1”
VUS 11/4”
VUS 11/2”
VUS 2”
Hydro-Air SystemsUS 3/8” *
Hydro-PlumbUS 1/2” *
Plus PEXUS 3/4” *
US 1” *
US 1¼” Hydro-Air Systems
U 16* (1/2”)
Hydro-Flex
U 20* (5/8”)
PEX-AL-PEX
U 25* (3/4”)
U 32 (1”)
Legend-PressVUS 1/2”
Press fitting systemVUS 3/4”
VUS 1”
VUS 11/4”
VUS 11/2”
VUS 2”
NIBCO®VUS 1/2”
TM
Press System VUS 3/4”
VUS 1”
VUS 11/4”
VUS 11/2”
VUS 2”
Uponor MLC
UP 16* (1/2”)
UP 20* (5/8”)
UP 25* (3/4”)
UP 32 (1”)
Viega ProPress®VUS 1/2”
VUS 3/4”
VUS 1”
VUS 11/4”
VUS 11/2”
VUS 2”
VUSR 2½” (PR-3B)
VUSR 3” (PR-3B)
VUSR 4” (PR-3B)
VUSF 2½” (PR-3B)
VUSF 3” (PR-3B)
VUSF 4” (PR-3B)
WATTS RADIANTUS 3/8” *
Watts WaterPEXUS 1/2” *
US 3/4” *
US 1” *
US 1¼” US 1½” WATTS RADIANTUS 3/8” *
Watts RadiantPEXUS 1/2” *
US 3/4” *
US 1” *
US 1¼” US 1½” WATTS RADIANT
U 16* (1/2”)
Watts RadiantPEX-AL
U 20* (5/8”)
U 25* (3/4”)
U 32 (1”)
ZURN INDUSTRIESUS 3/8” *
ZURN PEXUS 1/2” *
US 3/4” *
US 1” *
US 11/4” US 11/2” US 2” Art.-No.
571450
571455
571460
571465
571470
571770
571775
571780
571785
571790
571795
571450
571455
571460
571465
571470
570765
570775
570780
570785
571770
571775
571780
571785
571790
571795
571770
571775
571780
571785
571790
571795
572632
572636
572638
572640
571770
571775
571780
571785
571790
571795
572825
572826
572827
572819
572820
572821
571450
571455
571460
571465
571470
571475
571450
571455
571460
571465
571470
571475
570765
570775
570780
570785
571450
571455
571460
571465
571470
571475
571477
REMS pressing tongs for other U.S. pressfitting systems on request.
REMS pressing tong with two pivoted
mono block pressing jaws. Top-selling
standard version.
REMS pressing tong (4G) with two pivoted, parallel aligned pressing segments
for linear pressing of midsize dimensions.
REMS pressing tong (S) with one fixed
and two pivoted pressing segments,
for midsize dimensions.
REMS pressing ring (PR-3S) with 3 swivellable pressing segments mounted on a
jointed ring for large dimension complex
pressings. Ideal pressing through radially
controlled movement of pressing
segments, with adapter tong.
◄ REMS pressing rings (PR-3B) with 3
pressing segments for high quality, large
dimension pressings Optimum pressing by
radially controlled movement of the
pressing segments with adaptor tongs.
Accessories
Description
Adapter tong Z2
For driving REMS pressing rings (PR-3S) 42–54 mm
Adapter tong Z4
For driving REMS pressing rings (PR-3B) 75 mm
Adapter tong Z5
For driving REMS pressing rings (PR-3B) VF/VR 64 – 108
mm and VUSF/VUSR 2½ – 4”
Steel case with insert for 6 pressing tongs
(up to Ø 35 mm/1” and pressing tongs U 40, U 50,
TH 40, F 40, F 50, G 40, VUS 1¼”)/cropping tongs
and compartment for pipe cutter up to 42 mm
Steel case with insert for 2 pressing tongs
(M 42 (4G), M 54 (4G), V 42, V 54, H 40, H 40 A,
VUS 1½”, VUS 2”)
Steel case with insert for adapter tongs with
pressing rings M 42 (PR-3S) and M 54 (PR-3S) or
with pressing rings SA 42 (PR-3S) and M 54 (PR-3S).
Art.-No.
572795
572801
572802
570295
570290
572810
21
REMS Eco-Press
Up to Ø 26 mm / 1”!
Patent US 6,739,172
n Compact, handy, light. Drive unit with short tubular arms only 1.6 kg (3.5 lbs)
n Dividable tubular arms for individual adjustment of leverage to accomodate
different force demands of different pressfitting systems n Secure seating of pressing
tongs through locking pins n Final-lock-positioning enables visual check of perfectly
pressed joint (completely closed pressing tong)
REMS Eco-Press drive unit. Manual radial press for producing pressing joints of
plastic and multi-layer composite tubes Ø 10–26 mm, Ø 3/8 – 1”. For operation with
REMS pressing tongs. Drive unit with final-lock-positioning and dividable tubular arms.
In skin package.
Art.-No. 574000
REMS Power-Press E
n Electro-mechanic drive unit with maintenance-free reduction gear with safety
slipping clutch. Only 4.4 kg (9.8 lbs) n Proven universal motor 110 V, 50–60 Hz,
450 W (0.61 HP) n The pressing jaws remain closed until switched into reverse. Visual
confirmation of a perfectly pressed joint (completely closed pressing tong) possible
REMS Power-Press E Basic-Pack. Electric radial press for producing pressing joints
of all common pressfitting systems Ø 10–108 mm, Ø 3/8 – 4”. Drive unit.
Art.-No. 572110
REMS Power-Press E drive unit
In cardboard box.
Art.-No. 572100
REMS Power-Press ACC
n Powerful electro-hydraulic drive unit n Only 4.8 kg (10.6 lbs) n Swivelling pressing tongs seat (360°) n Proven universal motor 110 V, 50–60 Hz, 450 W (0.61 HP)
n Automatic-Circuit-Control (ACC): Automatic retraction after c ompletion of pressing
operation
Automatic Circuit Control
REMS Power-Press ACC Basic-Pack. Electro-hydraulic radial press for p
roducing
pressing joints of all common pressfitting systems Ø 10–108 mm, Ø 3/8 – 4”. Drive unit
with automatic circuit control. In sturdy steel case.
Art.-No. 577010
REMS Power-Press ACC drive unit
In cardboard box.
Art.-No. 577000
REMS Akku-Press
n Electro-hydraulic drive unit n Only 4.3 kg (9.5 lbs) n Optimum weight distribution
for single-hand operation n Swivelling pressing tongs seat (360°) n Acoustic signal
after successful completion of pressing operation enables confirmation of a perfectly
pressed joint (completely closed pressing tong)
charging status check
c signal
Acousti
REMS Akku-Press Basic-Pack. Cordless radial press with switch-off signal for
producing pipe pressing joints Ø 10–108 mm, Ø 3/8 – 4”. Swivelling pressing tongs
seat with automatic locking. Electro-hydraulic drive with powerful battery motor, robust
planetary gear, eccentric reciprocating pump and compact high power hydraulic
system. Safety tip switch. Battery, rapid charger Li-Ion/Ni-Cd 110 V, 50–60 Hz, 65 W.
REMS Akku-Press Li-Ion Basic-Pack
REMS Akku-Press ACC
n Electro-hydraulic drive unit n Only 4.3 kg (9.5 lbs) n Optimum weight distribution
for single-hand operation n Swivelling pressing tongs seat (360°) n Automatic-CircuitControl (ACC): Automatic retraction after completion of pressing operation (Automatic
Circuit Control) n Electronic service control with visual maintenance call after approx.
10,000 crimps
REMS Akku-Press ACC Basic-Pack. Cordless radial press with automatic
circuit control for producing pipe pressing joints Ø 10–108 mm, Ø 3/8 – 4”. Swivelling
pressing tongs seat with automatic locking. Electro-hydraulic drive with powerful
battery motor, robust planetary gear, eccentric reciprocating pump and compact high
power hydraulic system. Safety tip switch. Battery, rapid charger Li-Ion/Ni-Cd 110 V,
50–60 Hz, 65 W. In sturdy steel case.
REMS Akku-Press ACC Li-Ion Basic-Pack
battery motor 14.4 V, 380 W (0.52 HP), battery Li-Ion 14.4 V, 2.2 Ah
22
Art.-No. 571014
REMS cropping tong – for cutting threaded rods!
n High performance cropping tongs in forged and specially hardened steel for
cutting threaded rods n Reversible cropping inserts for double service life n Cropping
inserts with precise thread contour machined on CNC production centres ensure
guidance of threaded rod during cropping. Thus cropping to length, free from burrs.
After cropping the threaded rod, just screw it into the threaded connection
of the pipe clamp or nut n Drive through all REMS radial presses and
through suitable radial presses of other makes
REMS Akku-Ex-Press Q&E – fast and easy electric expanding!
n Compact, handy electric tool for fast, easy expanding of pipes/coils of the Uponor
ProPEX® system n Large expanding capacity up to Ø 40 mm, 11/2” n Compact, handy,
light n Drive unit with battery Li-Ion only 2.3 kg (5 lbs)
German
Quality Product
Patent US 7,284,330
Patent US 6,739,172
REMS cropping tong
REMS Akku-Ex-Press Q& E Basic-Pack. Cordless tube expander for expanding
tubes/coils up to Ø 1½”. Electro-hydraulic drive with automatic retraction, with powerful
battery motor 14.4 V, robust planetary gear, eccentric reciprocating pump and compact
high power hydraulic system. Safety tip switch. Battery, Rapid charger Li-Ion/Ni-Cd
110 V, 50–60 Hz, 65 W. Without expander heads. In sturdy steel case.
REMS Akku-Ex-Press Mini Q&E Li-Ion Basic-Pack
for threaded rods
UNC 3/8”
UNC 1/2”
Art.-No. 571845
Art.-No. 571850
Cropping insert UNC 3/8” (pair)
Cropping insert UNC 1/2” (pair)
Art.-No. 571846
Art.-No. 571851
Super simple – super quick
Accessories for battery presses and battery pipe expander:
Art.-No. 571540
Art.-No. 571550
Rapid charger 110 V, 50–60 Hz, 65 W Art.-No. 571560
REMS Power-Ex-Press Q&E – Fast, easy electric expanding
up to Ø 2”. With automatic return!
n Compact, handy electric tool for fast, easy expanding of tubes/coil of the Uponor
ProPEX® system n Automatic, gradual expansion until reaching the given end position
which is determined by the expander head n Use of original Uponor ProPEX® expander
heads, Ø ½ – 2” n Expanding device for holding the original Uponor ProPEX® 2”
expanding heads n Expanding device for holding the original Uponor ProPEX® ½ – 1½”,
expanding heads as an accessory n Compact, robust, job site-proven n Small in size,
slender design, drive unit only 5.3 kg
Cropping to length, free
from burrs
No time-consuming
deburring involved
After cropping the threaded
rod, just screw it into the
threaded connection of the
pipe clamp
REMS cable shear – Easy cutting of electric cable!
NEW
n High-grade cable shear in forged and specially hardened steel for cutting electric
cable n Replaceable cutting blades n Large cutting range n Drive through electric
REMS radial presses and through suitable radial presses of other makes
German
Quality Product
REMS Power-Ex-Press Q& E Basic-Pack. Electro-hydraulic pipe expander for expanding tubes/coils of the Uponor ProPEX® system Ø ½ – 2”, s ≤ 5,8 mm. Electro-hydraulic
drive with automatic retraction, with proven universal motor 110 V, 50 – 60 Hz, 450 W,
robust planetary gear, eccentric reciprocating pump and compact high power hydraulic
system. Safety tip switch. Expanding device 2”. Without expander heads.
In cardboard box.
Art.-No. 575017
REMS cable shear. Cable shear with replaceable blades (2 pcs.) for electric cable
≤ 300 mm2 (Ø 30 mm, 11/8”). In cardboard box.
Art.-No. 571887
Blades (2 pieces)
Art.-No. 571889
Adapter ½ – 1½”
for fitting the original expanding heads Uponor ProPEX® ½ – 1½” Art.-No. 575100
Steel case with insert
Art.-No. 570280
23
REMS Ax-Press 25 ACC – Axial compression up to 1¼” with
automatic return!
n Compact, handy, light n Drive machine with battery weighs only 2.9 kg (6.4 lbs), only
29 cm (1.3”) long n With preset compression head position for pressing compression
sleeve connectors with a clamping distance ≤ 82 mm in one action n Compact, handy,
light n Optimum weight distribution for single-hand operation n Ergonomically shaped
housing with recessed grip n Swivelling compression device for working in confined
area n Compression heads quickly interchangeable, without tools n Secure spring lock
seating of compression heads
REMS Mini-Cobra – by hand or electric!
n Proven hand unit for quick application n Indispensable to remove small blockages
n Robust, corrosion-resistant cable drum in shock-proof plastic n Highly flexible
cables for effortless feed-forward also in tight pipe bends n Drive by hand or electric
through a normal, slow rotating drill with stepless drive or standard screw driver
NEW
REMS Mini-Cobra. Drain cleaner for hand and electric drive. For pipes
Ø 20–50 (75) mm (Ø 1–3”), for cables Ø 6, 8, 10 mm. Complete with hand crank,
hexagon adapter for standard drive, cable 8×7.5 m. In cardboard box.
Art.-No. 170010
Drain cleaning cable 8 x 7.5 m Art.-No. 170200
10x10 m Art.-No. 170205
REMS Mini-Cobra A – quick removal of blockages!
German
Quality Product
REMS Ax-Press 25 ACC Basic-Pack. Cordless axial press for producing compression
sleeve joints Ø 12 – 40 mm, ½ – 1¼”. 40 mm stroke, for pressing compression sleeve
connections with a clamping distance ≤ 82 mm. For driving REMS pressing heads.
Electro-hydraulic drive with powerful battery motor 14,4 V, 420 W, robust planetary
gear, eccentric reciprocating pump and compact high power hydraulic system, safety
tip switch, swivelling pressing device. Battery Li-Ion 14.4 V, 1.3 Ah, rapid charger Li-Ion/
Ni-Cd 110 V, 50 – 60 Hz, 50 W. Without compression heads. In sturdy steel case.
Art.-No. 573033
n Combined thrust and grip handle for controlling the automatic feed-forward and
reverse and for safe holding n Easy insertion of cable directly through strainers in
sinks and drains n Drain cleaning cables with weather-proof and temperature
resistant plastic core n Robust, maintenance-free gear with safety slipping clutch
n Universal motor, 620 W (0.84 HP), high-torque forward and reverse at low speed
Automatic cable
feed and reverse!
REMS Ax-Press H – universal up to Ø 1”!
n Compact, job site proven n Handy and light. Drive unit only 1.4 kg (3 lbs) n
Quick-acting forward and release for easy, fast operation n Compression heads and
compression inserts are quickly interchangeable, without tools n Secure seating of
compression heads and compression inserts through spring locking n Adjustable
compression head positioning
REMS Mini-Cobra A. Electric drain cleaning machine with automatic feed-forward and
reverse, for pipes Ø 20–50 (75) mm (Ø 1–3”), for drain cleaning cables Ø 8 and 10 mm.
Complete with drive unit 110 W, 620 W (0.84 HP), 0–550 1/min, pipe and drain cleaning
cable with core 8 x 7.5 m. In cardboard box.
Art.-No. 170020
Drain cleaning cable with core 8 x 7.5 m
Art.-No. 170201
Drain cleaning cable 10x10 m
Art.-No. 170205
REMS Pull-Push – fast removal of blockages!
REMS Ax-Press H drive unit. Manual axial press for producing compression sleeve
joints Ø 1/2 –1” mm. With quick-acting forward and release. For driving REMS
compression heads. In cardboard box.
Art.-No. 574300
n High downforce thanks to front adjustable grip handle n 2 adaptor sleeves for optimum adaptation to the problem area: Short sleeve for sinks, basins and baths, long
sleeve for toilets.
NEW
REMS compression heads. Complete assortment of REMS compression heads for
ASFM F 2080 compression sleeve systems. Quickly interchangable, without tools.
High-grade compression heads in forged and specially hardened steel. The REMS
compression heads are system-specific and correspond to the respective compression sleeve system. Thus perfect system-conformity, safe jointing. Drive through REMS
Ax-Press H drive unit.
REMS compression heads (pair)
PKU 1/2”
PKU 3/4”
24
Art.-No. 573412
Art.-No. 573414
PKU 1”
PKU 11/4”
Art.-No. 573416
Art.-No. 573418
REMS Pull-Push. Manual suction / pressure pump for fast removal of blockages.
With short and long sleeves. In carton.
Art.-No. 170300
Universal diamond core drilling crowns
Quality Made in Germany. Universally usable for dry and wet drilling, hand held or
with drill stand. Connecting thread UNC 11/4” female. Drilling depth 420 mm (16.5”).
Specially developed, high quality diamond segments with high diamond percentage
and special bonding, for excellent drilling performance and very long life. Ideal for
universal applications in steel-reinforced concrete and masonry. Adapter for using the
REMS universal diamond core drilling crowns in drive machines of other makes, as an
accessory.
ally
Universble!
applica
NEW
e.g.
Granite
Steelreinforced
concrete
Asphalt
Ø x drilling depth x connection
UDKB
UDKB
UDKB
UDKB
UDKB
UDKB
UDKB
UDKB
UDKB
UDKB
UDKB
UDKB
UDKB
UDKB
UDKB
UDKB
UDKB
UDKB
32 (1.26”) x
42 (1.65”) x
52 (2.05”) x
62 (2.44”) x
72 (2.83”) x
82 (3.23”) x
92 (3.62”) x
102 (4”)
x
112 (4.41”) x
125 (4.92”) x
132 (5.20”) x
152 (5.98”) x
162 (6.38”) x
182 (7.16”) x
200 (7.87”) x
225 (8.86”) x
250 (9.84”) x
300 (11.81”)x
420
420
420
420
420
420
420
420
420
420
420
420
420
420
420
420
420
420
(16.53”)
(16.53”)
(16.53”)
(16.53”)
(16.53”)
(16.53”)
(16.53”)
(16.53”)
(16.53”)
(16.53”)
(16.53”)
(16.53”)
(16.53”)
(16.53”)
(16.53”)
(16.53”)
(16.53”)
(16.53”)
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
UNC
UNC
UNC
UNC
UNC
UNC
UNC
UNC
UNC
UNC
UNC
UNC
UNC
UNC
UNC
UNC
UNC
UNC
Poroton
Sandstone
Limestone
Number of
segments
Brickwork
Art.-No.
11/44181010
11/44181015
11/45181020
11/46181025
11/47181030
11/47181035
11/48181040
11/48181045
11/49181050
11/410181057
11/411181060
11/412181065
11/412181070
11/412181075
11/412181080
11/413181085
11/414181090
11/422181095
REMS Picus SR
Execution
REMS Picus
Electric diamond core drilling machines
Universal use
Universal drive machine for dry or wet drilling, hand held or with drill stand. Can be
used anywhere, in narrow angles, flush with the wall. Extremely versatile and efficient,
e.g. drilling in steel-reinforced concrete, masonry and other materials.
Inducti
vely
Resold soldered!
erable
!
High quality diamond segments
Quality Made in Germany. Specially developed, high quality diamond segments for
core drilling crowns, with high diamond percentage and special bonding, for excellent drilling performance and very long life. Ideal for universal applications in steel-
reinforced concrete and masonry.
Compact, handy drive machine for vibration-free core drilling, with drilling crown
uilding
connecting thread UNC 11/4 male, BSPP 1/2 female. Robust, suitable for the b
site. Extra light, only 6.4 kg (16 lbs). Simple, fast work, e.g. 200 mm (7.87”) in steel-
reinforced concrete Ø 62 mm (2.44”) in only 3 min. Practical spade handle and
stabiliser for hand held drilling. Throat for holding the drive machine in the drill stand.
Water supply for wet drilling, with adjustable shut-off valve and quick-coupling with
water stop and hose connection 1/2”. Suction rotor for sucking off dust for dry drilling
with connection for conventional vacuum cleaner, as accessory.
Drive
Robust, powerful 2200 W (3 HP) universal motor. Temperature control of the motor’s
field wires with a PTC resistor (Positive Temperature Coefficient) as overheating
protection. Stable, maintenance-free, 2-step gear. Blocking protection by safety slip
clutch. Touch switch with lock. Connecting cable with integrated personal
protection switch (PRCD).
Speed-Regulation
Stepless electronic speed regulation of the drive machine for selecting the speed
according to the material. The speed is steplessly adjustable on the dial: 200 rpm to
500 rpm (1st gear) or 500 rpm to 1200 rpm (2nd gear). The electronic speed control
that is being used keeps the selected speed constant, also under load. Advantage:
The optimum drilling speed (load speed) selected for the respective material remains
constant for the entire duration of the drilling. For excellent drilling performance and
very long life of the drilling crowns.
Multifunction electronics
Multifunction electronics with start-up current limiting for soft starting for delicate drilling start, automatic idle speed limiting for noise reduction and preservation
of the motor, overload and blocking protection for motor and gear.
25
REMS Picus SR Basic-Pack. Electric diamond core drilling machine with speed regulation. For core drilling in steel-reinforced concrete up to Ø 162 mm (6.38”), masonry
up to Ø 250 mm (10”). For dry or wet drilling, hand held or with drill stand. Drive
machine with drilling crown connection thread UNC 11/4 male, BSPP 1/2 female, maintenance-free 2-step gear with safety slip clutch, universal motor 110 V, 50–60 Hz,
2200 W (3 HP). Stepless electronic speed regulation 200 rpm to 500 rpm (1st gear) or
500 rpm to 1200 rpm (2nd gear), overheating protection. Multifunction electronics with
soft starting, idle speed limiting, overload protection, blocking protection. Touch switch
with lock. Personal protection switch (PRCD). Water supply device with adjustable
shut-off valve and quick coupling with water stop and ½” hose connection. Stabiliser.
Single open ended wrench size 32. In sturdy steel case.
Art.-No. 183010
REMS Picus S3 Basic-Pack. Electric diamond core drilling machine for core drilling
in steel-reinforced concrete up to Ø 152 mm (6”), masonry up to Ø 250 mm (10”). For
dry and wet drilling, hand held or with drill stand. Drive machine with drilling crown connection thread UNC 11/4 male, BSPP 1/2 female, maintenance-free 3-speed with safety
slip clutch, universal motor 110 V, 50–60 Hz, 2200 W (3 HP), multifunction electronics,
touch switch with lock, personal protection switch (PRCD). Load speed drilling spindle
530 1/min, 1280 1/min, 1780 1/min. Water supply with shutoff valve, quick-coupling with
water stop and hose connection 1/2”. Stabiliser. Single open-ended wrench size 32.
In strong steel case.Art.-No. 180011
REMS Simplex 2. Robust, handy drilling stand for core drilling up to Ø 200 mm. Drill
column made of rigid, unbendable square precision steel tube Ø 50 mm, with extra
narrow tolerance, for low-vibration guiding of the slide. Drilling column guided in sturdy
stand and double bolted for high rigidity during drilling. Steel section stand. 4 Set screws
for levelling unevenness of the floor, for exact standing position. Clamping bracket
for holding drive machines with clamping throat Ø 60 mm. Slide guided on all sides by
adjustable, pretensioned plastic slide bearings. Precision in-feed drive ensures easy,
low-vibration drilling and precise, low-vibration drill thrust. For high thrust pressure and
long life of the drilling crowns. Spirit level integrated in the slide for exact alignment of
the drill stand. Locking of the slide for simple assembly of the drilling crown and safe
transport. Stable clamping bracket, unbendable and rigid, for accommodating drive
units with Ø 60 mm clamping throat. Rack and pinion force transmission with ergonomically designed pressing lever which can be inserted in both sides of the slide. Wide
steel rack. Weight 12 kg (26 lbs). With tools, consisting of Allen key size 6, single open
ended wrench size SW 19 and SW 30 and fastening kit for masonry and concrete,
consisting of 2 M12 splaying anchors, 10 M12 hammer anchors for concrete, setting
iron for M12 hammer anchors, cord threaded bar M12 × 65, quick clamping nut, washer
in box. For REMS Picus S1, REMS Picus S3, REMS Picus SR and other makes.
Art.-No. 183700
REMS Titan. Robust, highly stable drilling stand for core drilling in steel-reinforced
concrete and other materials up to Ø 300 mm. For high demands. Drill column made of
rigid, unbendable square precision steel tube Ø 50 mm, with extra narrow tolerance, for
low-vibration guiding of the slide. Continuously tiltable with degree scale up to 45°, with
double support by adjustable, single-part steel girders, for maximum thrust pressure.
Highly stable, 3-sided guidance of the drill column in the base plate and triple cross
fastening for high rigidity in vertical drilling. 4 Eyebolts for levelling unevenness of
the floor, for exact standing position. Drill depth scale. Slide guided on all sides by
adjustable, pretensioned plastic slide bearings. Precision in-feed drive ensures easy,
low-vibration drilling and precise, low-vibration drill thrust. For high thrust pressure and
long life of the drilling crowns. Spirit level integrated in the slide for exact alignment
of the drill stand. Locking of the slide for simple assembly of the drilling crown and
safe transport. Rigid connection plate made of wear-resistant spheroidal iron. Quickclamping device for accommodating drive units with a suitable connection plate. Highly
stable clamping bracket, unbendable and rigid, for accommodating drive units with
Ø 60 mm clamping throat. Rack and pinion force transmission with ergonomically
designed pressing lever which can be inserted in both sides of the slide. Wide steel
rack. Base plate with groove for sealing ring of the vacuum fastening. Vacuum fastening
as accessory. Drill column with adjustable clamping head for clamping the drill stand
between the ceiling and floor or between two walls. Mobile drill stand for easy transport
Weight 19.5 kg (43 lbs). With tools, consisting of Allen key size 6, single open ended
wrench size SW 19 and SW 30 and fastening kit for masonry and concrete, consisting
of 2 M12 splaying anchors, 10 M12 hammer anchors for concrete, setting iron for M12
hammer anchors, cord threaded bar M12 × 65, quick clamping nut, washer in box.
System advantage: For REMS Picus S1, REMS Picus S3, REMS Picus SR, REMS
Picus S2/3,5 and other makes.Art.-No. 183600
26
Accessories for REMS Picus SR / REMS Picus S3
Description
Water pressure tank for 8 ltr of water,
for wet drilling without water connection
Titan drilling template for easy setting of the fastening
holes. For REMS Titan drilling stand.
Carbide masonry drills Ø 15 mm SDS-plus for hammer anchors M12
Hammer anchor M12 (concrete), 50 pieces
Setting iron for hammer anchor M12
Carbide masonry drills Ø 20 mm SDS-plus for splaying anchors M12
Splaying anchor M12 (masonry), 10 pieces,
reusable
Quick clamping set 160 for fastening the drilling stand
with anchors, consisting of cord threaded bar 160 mm with
M12 × 52 thread, quick clamping nut, washer.
Quick clamping set 500 for fastening the drilling stand
without anchor, consisting of cord threaded bar 500 mm, 2
quick clamping nuts, 2 washers
Titan vacuum fastening, consisting of cover plate
with nipple for ⅜” screw connection and sealing ring
for base plate.
Vacuum pump, for vacuum ≤ - 900 mbar (90%),
consisting of dry running rotary slide pump, oil-free,
performance 6 m3/h, condenser motor 230 V,
50 – 60 Hz, 250 W, splash water-protected, inside
suction filter with silencer function and 5 m PVC
fabric hose with bayonet coupling.
Laser drilling centre pointer
G ½ drill aid with carbide masonry drill Ø 8 mm
Carbide masonry drill Ø 8 mm for drilling aid
Single open ended wrench size 41 for loosening
the universal diamond core drilling crowns
Light loosening ring, for light loosening
of the diamond core crown
Drilling crown extension 200 mm
Suction rotor for dust suction with connection
for conventional vacuum cleaner
Water suction device, for wet drilling up to Ø 170 mm,
consisting of water collection ring with sealing ring,
rubber washer Ø 200 mm and universal pressure pad for all
REMS drilling stands.
Rubber washer Ø 200 mm, 10 pieces,
for water suction device
Sharpening stone for diamond core drilling crowns
Spirit level, magnetic, with 3 indicators for setting
the stand 3-dimensionally
REMS
Picus S1
Art.-No.
182006
183605
079018
079005
182050
079019
079006
079010
183607
183603
183670
183604
180150
079013
079003
180015
180155
180160
183606
183675
079012
182009
REMS
Picus S2/3.5
REMS Picus S1
REMS Picus S2/3.5
available on
special order
27
Germany Headquarters
REMS-WERK Christian Föll und Söhne GmbH
Postfach 1631 · D-71306 Waiblingen
Stuttgarter Straße 83 · D-71332 Waiblingen
Tel +49 7151 17 07-0
Fax +49 7151 17 07-110
info@rems.de
www.rems.de
Denmark: REMS Scandinavia A/S
Snedkervej 1 · DK-4600 Køge
Tel +45 56 63 14 00 · Fax +45 56 63 11 78
DNK@rems.de
France: REMS S.à.r.l.
2, Rue du Stade · F-67250 Hoffen
Tel +33 388 80 44 53 · Fax +33 388 80 99 43
FRA@rems.de
Great Britain: REMS (UK) Ltd.
Unit 5 · Ash Industrial Estate
Flex Meadow · Harlow · Essex CM19 5TJ
Tel +44 1279 413698 · Fax +44 1279 413704
GBR@rems.de
Your distributor:
Spain: REMS ESPAÑA, S.A.U.
Pol. Ind. San José de Valderas
Calle Herramientas, 28 · E-28918 Leganés (Madrid)
Tel +34 916 444 833 · Fax +34 916 430 155
ESP@rems.de
Czech Republic: REMS Česká republika s.r.o.
Nádražní 271 · CZ 253 01 Hostivice
Tel +420 2 20 98 28 80 · Fax +420 2 20 98 28 83
CZE@rems.de
Turkey: REMS Makine ve El Aletleri Ltd. Şti.
Kaşüstü Mevkii · Samandıra Caddesi No. 28
TR-34858 Büyükbakkalköy/Maltepe/İstanbul
Tel +90 216 311 75 05 · Fax +90 216 311 75 06
TUR@rems.de
5995 149th Street West
Apple Valley, MN 55124
phone952.432.8325
fax952.432.3298
Sale only through specialist dealers
Poland: REMS POLSKA Sp. z o.o.
Dąbrowa · Ulica Piaskowa 19
PL 62-070 Dopiewo
Tel +48 61 654 09 00 · Fax +48 61 654 09 05
POL@rems.de
Teal Corporation
Italy: REMS S.r.l.
Via Sirtori, 13/D · I-20017 Passirana di Rho (Milano)
Tel +39 02 9 30 21 11 · Fax +39 02 9 31 02 45
ITA@rems.de
E 04/2011 090540 USA · Subject to alterations and errors. © Copyright 2011 by REMS-WERK Christian Föll und Söhne GmbH, Waiblingen.
w w w. r e m s . d e

Machines and Tools for Pipe Working

Transcription

Similar documents

Page 1 n e w p r o d u c t s s p r i n g / s u m m e r 2 0 1 4 Time for

PU-Clogs 2012

Vivantes Komfortklinik am Humboldt-klinikum, Berlin, Deutschland

VitraHaus, Weil am Rhein, Deutschland - Reference

8 Effective Classroom Practices - NYS PBIS Technical Assistance Center

Product sheet BBPE050.4A

ELEC TRIC DIE ST OCK

Machines and Tools for Pipe Working

easyPilot Cobra™ Shootbolt

012602 Art. VESPINO