docV-belt and V-belt Pulleys
download 
Report Transcription
V-belt and V-belt Pulleys
Products | Solutions | Service V- Belts and V- Belt Pulleys Chapter 11 We hereby reserve the right to change content of data in this catalogue at any time without notice. Our company shall not be held responsible for neither possible discrepancies in catalogue content nor any damage caused by wrong use of products or information. Lönne Scandinavia AS reserves the prohibition to publish pages or whole parts of this catalogue without authorization. All product names occurring or referred to in this catalogue are or may be registered trademarks belonging to their respective producers or trademark owners. The dimensions are in mm. Illustrations are not binding. V- Belts and V- Belt Pulleys Chapter 11 Index Page Small profile V- belt, Quad- Power III 5 Small profile V- belt, Super HC MN & Super HC 8 Classical V- belt, VulcoPower 10 Double V- belt, Hi- Power 12 Heavy Duty V- belts 14 Heavy Duty V- belts Raw edge Quad- Power II 16 Heavy Duty V- belts, Super HC & Hi- Power Powerband 18 V- belts for variable speed drives, Multi- speed 21 Polyurethane V- belts for compact drives, PolyFlex 22 Polyurethane multiple V- belt 24 Heavy Duty Multi Ribbed V- belts & round belts for joint 26 Joint Belts Round Belts 28 V- Belt pulleys for Taper Bushes 30 V- belt Pulleys with Solid Hub 44 Flat Belt Pulleys for Taper Bushes 51 Poly V- Pulleys 53 Taper bushes –Metric 58 Taper Bushes Imperial 59 Important addresses and phone numbers. General info. 61 3 V- Belts and V- Belt Pulleys Chapter 11 Small Profile V- belts New generation raw edge V- belts QUAD- POWER® III The Gates Quad- Power® belt has undergone several evolutions in design since its introduction over 15 years ago. New materials and advanced- design features have led to a new generation of Quad- Power® III V- belt drives that outperform all similarly sized belt drives in a wide range of applications, yielding cost advantages for users, and greater design freedom for engineers. Construction features The basic belt consists of a newly developed rubber compound which withstands chemically aggressive environments (acid and base), ageing, ozone, UV and heat. Even with severe slippage, the belt will not catch fire from heat build- up. High- performance fibres embodied in the compound provide improved abrasion and wear resistance. The outstanding cord support in the undercord section achieved by the transverse orientation of the fibres reinforces the belt’ s overall longitudinal flexibility and transverse rigidity. The special notch profile with optimised geometry ensures perfect belt stability. The precision- ground sidewalls give a uniform wedging action. The tensile section consists of high- strength, low- elongation polyester tensile cords which are embedded in a newly developed blue- coloured adhesion layer. This layer develops an extra high bonding level between tensile cords and undercord material. The exceptional flexibility gives the belt excellent reversed bending properties when backside idlers are used. high- strength low- elongation polyester tensile cords embedding adhesion layer special notch profile fibre- reinforced rubber compound 5 V- Belts and V- Belt Pulleys Chapter 11 Additional benefits Extended temperature range: from -40°C up to +110°C. Extraordinary power capacity: at least 15% higher power ratings than Gates Quad- Power® II belts. Substantially reduced noise level. Static conductive (ISO 1813) and can as such be used in the conditions described in the Directive 94/9/ EC ATEX. REACH and RoHS compliant. High dimensional precision. All sizes meet and even exceed Gates UNISET tolerances and can be installed without matching. Smooth- running operation. Space savings and design freedom. Minimal belt tension loss. Long and trouble- free service life reducing replacement and maintenance costs. Environment- friendly: halogen- free (e.g. chlorine). Significantly better resistance to static ageing. Taken together, these benefits result in a top quality, high- performance, low- maintenance V- belt drive that reduces the material and labour cost of maintenance, while at the same time improving uptime and productivity. Performance Noice Level dBA Relative Performance * These results were obtained under extreme test conditions. Sections and nominal dimensions * XPZ/3VX XPA XPB/5VX XPC Width (mm) 10 13 16 22 Height (mm) 8 10 13 18 Recommended minmum pulley diameter Profile Pulley diameter, mm XPZ 56 XPA 80 XPB 112 XPC 180 * As described in the ISO standards, nominal dimensions define the pulleys for which these belts are suitable. They do not represent the exact belt size. These are determined by the belt construction and are Gates proprietary. 6 V- Belts and V- Belt Pulleys Chapter 11 Belt Range XPZ/3VX XPZ/3VX XPA XPA XPB/5VX Datum ISO RMA length desccription description mm XPZ600 600 3VX238 XPZ630 630 3VX250 XPZ637 637 3VX252 XPZ662 662 3VX262 XPZ670 670 3VX265 XPZ687 687 3VX272 XPZ710 710 3VX280 XPZ722 722 3VX286 XPZ730 730 3VX289 XPZ737 737 3VX292 XPZ750 750 3VX297 XPZ762 762 3VX300 XPZ772 772 3VX305 XPZ787 787 3VX311 XPZ800 800 3VX315 XPZ812 812 3VX321 XPZ837 837 3VX331 XPZ850 850 3VX335 XPZ862 862 3VX341 XPZ875 875 3VX346 XPZ887 887 3VX350 XPZ900 900 3VX355 XPZ912 912 3VX360 XPZ925 925 3VX366 XPZ937 937 3VX370 XPZ950 950 3VX375 XPZ962 962 3VX380 XPZ975 975 3VX385 XPZ980 980 3VX387 XPZ987 987 3VX390 XPZ1000 1000 3VX395 XPZ1012 1012 3VX400 XPZ1030 1030 3VX407 XPZ1037 1037 3VX410 XPZ1060 1060 3VX419 XPZ1080 1080 3VX425 XPZ1087 1087 3VX429 XPZ1112 1112 3VX439 XPZ1120 1120 3VX442 XPZ1140 1140 3VX450 XPZ1150 1150 3VX454 XPZ1162 1162 3VX459 XPZ1180 1180 3VX464 XPZ1187 1187 3VX469 XPZ1202 1202 3VX475 XPZ1212 1212 3VX479 XPZ1237 1237 3VX487 XPZ1250 1250 3VX494 XPZ1262 1262 3VX498 XPZ1270 1270 3VX500 XPZ1280 1280 3VX505 XPZ1287 1287 3VX508 XPZ1312 1312 3VX518 XPZ1320 1320 3VX520 XPZ1337 1337 3VX530 XPZ1362 1362 3VX538 XPZ1400 1400 3VX553 XPZ1412 1412 3VX557 Datum ISO RMA length desccription description mm XPZ1420 1420 3VX560 XPZ1437 1437 3VX567 XPZ1450 1450 3VX572 XPZ1487 1487 3VX587 XPZ1500 1500 3VX592 XPZ1512 1512 3VX597 XPZ1520 1520 3VX600 XPZ1537 1537 3VX607 XPZ1550 1550 3VX612 XPZ1587 1587 3VX626 XPZ1600 1600 3VX630 XPZ1650 1650 3VX650 XPZ1687 1687 3VX666 XPZ1700 1700 3VX670 XPZ1750 1750 3VX690 XPZ1800 1800 3VX710 XPZ1850 1850 3VX730 XPZ1900 1900 3VX750 XPZ1950 1950 3VX771 XPZ2000 2000 3VX790 XPZ2030 2030 3VX800 XPZ2120 2120 3VX836 XPZ2160 2160 3VX850 XPZ2240 2240 3VX883 XPZ2280 2280 3VX900 XPZ2360 2360 3VX931 XPZ2410 2410 3VX950 XPZ2500 2500 3VX986 XPZ2540 2540 3VX1000 XPZ2650 2650 3VX1045 XPZ2690 2690 3VX1060 XPZ2800 2800 3VX1104 XPZ2840 2840 3VX1120 XPZ3000 3000 3VX1180 XPZ3150 3150 3VX1242 XPZ3350 3350 3VX1320 XPZ3550 3550 3VX1400 ISO Datum desccription length mm XPA690 690 XPA732 732 XPA747 747 XPA757 757 XPA782 782 XPA800 800 XPA832 832 XPA850 850 XPA857 857 XPA882 882 XPA900 900 XPA907 907 XPA925 925 XPA932 932 XPA950 950 XPA957 957 XPA975 975 XPA982 982 XPA1000 1000 XPA1007 1007 XPA1030 1030 XPA1060 1060 XPA1082 1082 XPA1090 1090 XPA1107 1107 XPA1120 1120 XPA1140 1140 XPA1150 1150 XPA1157 1157 XPA1180 1180 XPA1207 1207 XPA1215 1215 XPA1232 1232 XPA1250 1250 XPA1257 1257 XPA1282 1282 XPA1285 1285 XPA1307 1307 XPA1320 1320 XPA1332 1332 XPA1357 1357 XPA1360 1360 XPA1367 1367 XPA1382 1382 XPA1400 1400 XPA1450 1450 XPA1457 1457 XPA1482 1482 XPA1500 1500 XPA1507 1507 XPA1532 1532 XPA1550 1550 XPA1582 1582 XPA1600 1600 XPA1632 1632 XPA1650 1650 XPA1657 1657 XPA1680 1680 ISO Datum desccription length mm XPA1700 1700 XPA1732 1732 XPA1750 1750 XPA1782 1782 XPA1800 1800 XPA1850 1850 XPA1900 1900 XPA1950 1950 XPA2000 2000 XPA2060 2060 XPA2120 2120 XPA2180 2180 XPA2240 2240 XPA2360 2360 XPA2430 2430 XPA2500 2500 XPA2650 2650 XPA2800 2800 XPA3000 3000 XPA3150 3150 XPA3350 3350 XPA3550 3550 XPA3750 3750 XPA4000 4000 Datum ISO RMA length desccription description mm XPB1000 1000 5VX398 XPB1060 1060 5VX422 XPB1080 1080 5VX430 XPB1120 1120 5VX445 XPB1180 1180 5VX470 XPB1250 1250 5VX497 XPB1260 1260 5VX500 XPB1320 1320 5VX524 XPB1340 1340 5VX530 XPB1400 1400 5VX556 XPB1410 1410 5VX560 XPB1450 1450 5VX575 XPB1500 1500 5VX595 XPB1510 1510 5VX600 XPB1550 1550 5VX615 XPB1590 1590 5VX630 XPB1600 1600 5VX634 XPB1650 1650 5VX654 XPB1690 1690 5VX670 XPB1700 1700 5VX674 XPB1750 1750 5VX693 XPB1800 1800 5VX713 XPB1850 1850 5VX733 XPB1900 1900 5VX753 XPB1950 1950 5VX772 XPB2000 2000 5VX790 XPB2020 2020 5VX800 XPB2120 2120 5VX840 XPB2150 2150 5VX850 XPB2240 2240 5VX886 XPB2280 2280 5VX900 XPB2300 2300 5VX910 XPB2360 2360 5VX934 XPB2410 2410 5VX953 XPB2500 2500 5VX990 XPB2530 2530 5VX1000 XPB2650 2650 5VX1050 XPB2680 2680 5VX1060 XPB2800 2800 5VX1108 XPB2840 2840 5VX1123 XPB2900 2900 5VX1146 XPB2990 2990 5VX1180 XPB3000 3000 5VX1186 XPB3150 3150 5VX1245 XPB3320 3320 5VX1312 XPB3350 3350 5VX1323 XPB3440 3440 5VX1359 XPB3550 3550 5VX1400 XPB3750 3750 5VX1481 XPB4000 4000 5VX1579 XPB4250 4250 5VX1678 XPB4500 4500 5VX1776 XPB4750 4750 5VX1875 XPB5000 5000 5VX1973 Ld = Lp Ld = Datum Lenght Lp = Pitch Lenght XPC Quad- Power® III ordering code is composed as follows: XPZ600 XPZ Section 600 - Datum length (mm) ISO Datum desccription length mm XPC1900 1900 XPC2000 2000 XPC2120 2120 XPC2240 2240 XPC2360 2360 XPC2500 2500 XPC2650 2650 XPC2800 2800 XPC3000 3000 XPC3150 3150 XPC3350 3350 XPC3550 3550 XPC3750 3750 XPC4000 4000 XPC4250 4250 XPC4500 4500 XPC4750 4750 XPC5000 5000 7 V- Belts and V- Belt Pulleys Chapter 11 Small Profile V- belts Raw egde- moulded notch/ Wrapped,narrow section V- belt. Super HC® MN & Super HC® In addition to the Super HC® wrapped, narrow section V- belt is the Super HC® Moulded Notch V- belt construction. Super HC® MN V- belts put more power where high speeds, high speed ratios or small pulley diameters are required, thus offering significant advantages over classical section V- belts. This belt is highly recommended for use on all industrial heavyduty, narrow section V- belt drives, as the increased transmission efficiency allows more compact and highly economical drive design. Super HC® MN belts are available up to 5000 mm ISO datum lengths. Identification Durable yellow marking indicating type and dimensions. Construction SPZ Description MN Wrapped Super HC Datum lenght mm Description MN Wrapped Super HC Datum lenght mm SPZ487 487 SPZ1347MN SPZ1347 1347 SPZ560MN SPZ512 SPZ560 512 560 SPZ1362MN SPZ1360 SPZ1362 1360 1362 SPZ562MN SPZ562 562 SPZ1387MN SPZ1387 1387 SPZ612MN SPZ587 SPZ612 587 612 SPZ1400MN SPZ1412MN SPZ1400 SPZ1412 1400 1412 SPZ630MN SPZ615 SPZ630 615 630 SPZ1420MN SPZ1437MN SPZ1437 1420 1437 SPZ637MN SPZ637 637 SPZ1450MN SPZ1450 1450 SPZ662MN SPZ662 662 SPZ1462MN SPZ1462 1462 SPZ670MN SPZ687MN SPZ670 SPZ687 670 687 SPZ1487MN SPZ1500MN SPZ1487 SPZ1500 1487 1500 SPZ710MN SPZ722MN SPZ710 SPZ722 710 722 SPZ1512MN SPZ1520MN SPZ1512 1512 1520 SPZ730MN SPZ737MN SPZ730 SPZ737 730 737 SPZ1537MN SPZ1550MN SPZ1537 SPZ1550 1537 1550 SPZ750MN SPZ750 750 SPZ1562MN SPZ1562 1562 SPZ1575 1575 SPZ760MN Super HC® MN Moulded notches reduce and evenly distribute thermal and bending stresses. The moulded notch pattern also reduces noise. Precision- ground straight sidewalls give a uniform wedging action and ensure the belt fits correctly in the pulley grooves. Back idlers can be used. Flex- bonded tensile cords are vulcanised as one solid unit making the belt highly resistant to tensile and flexing forces, fatigue and shock loads. Elastomeric compound protects the belt against heat, ozone and sunlight. Even with severe slippage, the belt will not catch fire from heat build- up. Static conductive (ISO 1813) and can as such be used in the conditions described in the Directive 94/9/ EC - ATEX. Super HC® Arched top, concave sidewalls and rounded corners provide uniform tensile loading and uniform pulley sidewall contact for excellent belt service and reduced pulley wear. The Flex- Weave® oil and heat resistant cover protects the belt core from the toughest environments. The vulcanised Flex- bonded tensile cords provide superior resistance to tensile and flexing forces, fatigue and shock loads. Static conductive (ISO 1813) and can as such be used in the conditions described in the Directive 94/9/ EC - ATEX. Advantages Excellent performance/ cost ratio. More power in the same space or same power in 1/3 to 1/2 less space as compared to classical section V- belts. Cost and space savings by reducing size of pulleys, bearings, guards and mounts. Improved belt life reducing expensive maintenance time. Match system: all sizes meet Gates UNISET tolerances, they can be installed without matching. Sections and nominal dimensions 760 SPZ762MN SPZ772MN SPZ762 SPZ772 762 772 SPZ1587MN SPZ1600MN SPZ1587 SPZ1600 1587 1600 SPZ775MN SPZ775 775 SPZ1612MN SPZ1612 1612 SPZ787MN SPZ787 787 SPZ1637MN SPZ1637 1637 SPZ800MN SPZ812MN SPZ825MN SPZ800 SPZ812 SPZ825 800 812 825 SPZ1650MN SPZ1662MN SPZ1687MN SPZ1650 SPZ1662 SPZ1687 1650 1662 1687 SPZ837MN SPZ850MN SPZ837 SPZ850 837 850 SPZ1700MN SPZ1737MN SPZ1700 SPZ1737 1700 1737 SPZ862MN SPZ875MN SPZ862 SPZ875 862 875 SPZ1750MN SPZ1762MN SPZ1750 SPZ1762 1750 1762 SPZ887MN SPZ900MN SPZ887 SPZ900 887 900 SPZ1782MN SPZ1787MN SPZ1787 1782 1787 SPZ912MN SPZ925MN SPZ912 SPZ925 912 925 SPZ1800MN SPZ1812MN SPZ1800 SPZ1812 1800 1812 SPZ937MN SPZ950MN SPZ937 SPZ950 937 950 SPZ1837MN SPZ1850MN SPZ1837 SPZ1850 1837 1850 SPZ962MN SPZ975MN SPZ962 SPZ975 962 975 SPZ1862MN SPZ1887MN SPZ1862 SPZ1887 1862 1887 SPZ987MN SPZ1000MN SPZ987 SPZ1000 987 1000 SPZ1900MN SPZ1937MN SPZ1900 SPZ1937 1900 1937 SPZ1010MN SPZ1012MN SPZ1012 1010 1012 SPZ1950MN SPZ1987MN SPZ1950 SPZ1987 1950 1987 SPZ1024 1024 1025 SPZ2000MN SPZ2037MN SPZ2000 SPZ2037 2000 2037 SPZ1030MN SPZ1030 1030 SPZ2060MN SPZ2060 2060 SPZ1037MN SPZ1037 1037 SPZ2120MN SPZ2120 2120 SPZ1047MN SPZ1047 1047 SPZ2137MN SPZ2137 2137 SPZ1060MN SPZ1062MN SPZ1060 SPZ1062 1060 1062 SPZ2160MN SPZ1077MN SPZ1077 1077 SPZ2180MN SPZ2180 2180 1080 SPZ2187MN SPZ2187 2187 SPZ2240 2240 SPZ1025MN SPZ1080MN SPZ(- MN) SPA(- MN) SPB(- MN) SPC(- MN) Height mm 8 10 13 18 2160 SPZ1087MN SPZ1087 1087 SPZ2240MN SPZ1090MN SPZ1090 1090 SPZ2262MN SPZ1112MN SPZ1120MN SPZ1112 SPZ1120 1112 1120 SPZ2280MN SPZ2287MN SPZ1137MN SPZ1140MN SPZ1137 1137 1140 SPZ2360MN SPZ2410MN SPZ2360 2360 2410 SPZ1150MN SPZ1162MN SPZ1150 SPZ1162 1150 1162 SPZ2430MN SPZ2500MN SPZ2430 SPZ2500 2430 2500 SPZ1180MN SPZ1180 1180 SPZ2540MN SPZ2540 2540 SPZ1187MN SPZ1187 1187 SPZ2650MN SPZ2650 2650 SPZ1200MN SPZ1202MN SPZ1202 1200 1202 SPZ2690MN SPZ2800MN SPZ2690 SPZ2800 2690 2800 SPZ1212MN SPZ1212 1212 SPZ2840MN SPZ2840 2840 SPZ1215 1215 SPZ3000MN SPZ3000 3000 SPZ1237MN SPZ1237 1237 SPZ3150MN SPZ3150 3150 SPZ1250MN SPZ1262MN SPZ1250 SPZ1262 1250 1262 SPZ3350MN SPZ3550MN SPZ3350 SPZ3550 SPZ3750 3350 3550 3750 SPZ1270MN Width mm 10 13 16 22 SPZ2150 1270 SPZ1285 1285 SPZ1287MN SPZ1287 1287 SPZ1312MN SPZ1312 1312 SPZ1320MN SPZ1320 1320 SPZ1337MN SPZ1340MN SPZ1337 1337 1340 2262 SPZ2287 2280 2287 8 V- Belts and V- Belt Pulleys Chapter 11 SPA Description Wrapped Datum lenght MN Super HC mm Description Wrapped Datum lenght MN Super HC mm SPB SPC Description Wrapped Datum Lenght MN Super HC mm Description Wrapped Datum Lenght MN Super HC mm SPA732MN SPA732 732 SPA1850 1850 SPB1250MN SPA757MN SPA757 757 SPA1857MN SPA1857 1857 SPB1260MN SPA782MN SPA782 782 SPA1882MN SPA1882 1882 SPB1320MN SPA800MN SPA807MN SPA800 SPA807 800 807 SPA1900MN SPA1907MN SPA1900 SPA1907 1900 1907 SPB1340MN 819 SPA1932MN SPA1932 1932 SPB1400MN SPA819MN SPB1250 1250 SPC2000MN SPC2000 2000 1260 SPC2120MN SPC2120 2120 SPB1320 1320 SPC2240 SPC2360 2240 2360 SPB1360 1340 1360 SPC2240MN SPC2360MN SPC2500MN SPB1400 1400 SPC2500 SPC2550 2500 2550 1410 1450 SPC2650MN SPC2650 2650 SPB1450 SPC2800MN SPC2800 2800 SPB1500 1500 1510 SPC3000MN SPC3150MN SPC3000 SPC3150 3000 3150 SPB1550 1550 SPC3350MN SPC3350 3350 1590 SPC3550MN SPC3550 3550 SPB1600 SPB1650 1600 1650 SPC3750MN SPC3750 3750 SPC4000MN 4000 4100 SPB1700 1690 1700 SPC4000 SPC4100 SPC4250MN SPC4250 4250 SPB1750 SPB1778 1750 1778 SPC4500MN SPC4500 4500 SPC4750MN SPC4750 4750 SPB1800 1800 SPC5000 5000 SPC5300 SPC5600 5300 5600 SPA832MN SPA850MN SPA832 SPA850 832 850 SPA1950MN SPA1957MN SPA1950 SPA1957 1950 1957 SPB1410MN SPA857MN SPA882MN SPA857 SPA882 857 882 SPA1982MN SPA2000MN SPA1982 SPA2000 1982 2000 SPB1500MN SPB1510MN SPA900MN SPA900 900 SPA2032MN SPA2032 2032 SPA907MN SPA907 907 SPA2057MN SPA2057 2057 SPB1590MN SPA925MN SPA932MN SPA925 SPA932 925 932 SPA2060MN SPA2082MN SPA2060 SPA2082 2060 2082 SPB1600MN SPA950MN SPA957MN SPA950 SPA957 950 957 SPA2120MN SPA2132MN SPA2120 SPA2132 2120 2132 SPB1690MN SPB1700MN SPA975MN SPA982MN SPA975 SPA982 975 982 2180 2182 SPB1750MN SPA2182MN SPA2180 SPA2182 SPA1000MN SPA1000 1000 SPA2207MN SPA2207 2207 SPB1800MN SPA1007MN SPA1007 1007 SPA2232MN SPA2232 2232 SPB1850 1850 SPA1030MN SPA1032MN SPA1030 SPA1032 1030 1032 SPA2240MN SPA2282MN SPA2240 SPA2282 2240 2282 SPB1860 SPB1900 1860 1900 SPC5800 5800 SPA1057 1057 SPA2300MN SPA2300 2300 SPB1930 1930 SPC6000 6000 SPA1060MN SPA1060 1060 SPA2307MN SPA2307 2307 SPB1950 1950 SPA1082MN SPA1090MN SPA1107MN SPA1082 SPA1090 SPA1107 1082 1090 1107 SPA2332MN SPA2360MN SPA2382MN SPA2332 SPA2360 SPA2382 2332 2360 2382 SPB2000 SPB2020 SPB2060 2000 2020 2060 SPC6300 SPC6500 6300 6500 SPA1120MN SPA1132MN SPA1120 SPA1132 1120 1132 SPA2430MN SPA2430 SPA2432 2430 2432 SPB2098 SPB2120 2098 2120 SPC6700 SPC7100 SPC7500 6700 7100 7500 SPA1140MN SPA1150MN SPA2482MN SPA2500MN SPA2482 SPA2500 2482 2500 SPB2150 SPB2180 2150 2180 SPC8000 SPC8500 8000 8500 SPA1150 1140 1150 SPC9000 9000 SPA1157MN SPA1180MN SPA1157 SPA1180 1157 1180 SPA2532MN SPA2582MN SPA2532 SPA2582 2532 2582 SPB2200 SPB2240 2200 2240 SPC9500 9500 SPA1207MN SPA1215MN SPA1207 SPA1215 1207 1215 SPA2607MN SPA2632MN SPA2607 SPA2632 2607 2632 SPB2280MN SPB2280 SPB2300 2280 2300 SPA1232MN SPA1250MN SPA1232 SPA1250 1232 1250 SPA2650MN SPA2682MN SPA2650 SPA2682 2650 2682 SPB2360MN SPB2360 SPB2391 2360 2391 SPA1257MN SPA1272MN SPA1257 SPA1272 1257 1272 SPA2732MN SPA2782MN SPB2400 SPA2782 2732 2782 SPB2410MN 2400 2410 SPA1282MN SPA1285MN SPA1282 SPA1285 1282 1285 SPA2800MN SPA2832MN SPA2800 SPA2832 2800 2832 SPB2500MN SPB2530MN SPB2500 2500 2530 SPA1307MN SPA1320MN SPA1307 SPA1320 1307 1320 SPA2847MN SPA2847 SPA2872 2847 2872 SPB2650MN SPB2600 SPB2650 2600 2650 SPA1332MN SPA1357MN SPA1332 SPA1357 1332 1357 SPA2882MN SPA2900MN SPA2882 SPA2900 2882 2900 SPB2680MN SPB2800MN SPB2680 SPB2800 2680 2800 SPA1360MN SPA1360 1360 SPA2932MN SPA2932 2932 SPB2840MN SPB2840 2840 SPA1382MN SPA1382 1382 SPA2982MN SPA2982 2982 SPB2850 2850 SPA1400MN SPA1400 1400 SPA3000MN SPA3000 3000 SPB2900 2900 SPA1407MN SPA1432MN SPA1407 SPA1432 1407 1432 SPA3032 SPA3082 3032 3082 SPB2990MN SPB3000MN SPB3000 2990 3000 SPA1450MN SPA1450 1450 SPA3150 3150 SPB3150MN SPB3150 3150 SPA1457MN SPA1457 1457 SPA3182 3182 SPB3250 3250 SPA1482MN SPA1482 1482 SPA3282 3282 SPB3320 3320 SPA1500MN SPA1500 1500 SPA3350MN SPA3350 3350 SPB3350MN SPB3350 3350 SPA1507MN SPA1532MN SPA1507 SPA1532 1507 1532 SPA3550MN SPA3382 SPA3550 3382 3550 SPB3550MN SPB3450 SPB3550 3450 3550 SPA1550MN SPA1557MN SPA1550 SPA1557 1550 1557 SPA3750MN SPA3650 SPA3750 3650 3750 SPB3750MN SPB3650 SPB3750 3650 3750 SPA1582MN SPA1600MN SPA1582 SPA1600 1582 1600 SPA4000 SPA4250 4000 4250 SPB3800 SPB3870 3800 3870 SPA1607MN SPA1607 1607 1632 4500 5000 4000 SPA1632 SPA4500 SPA5000 SPB4000 SPA1632MN SPB4120 4120 SPA1650MN SPA1657MN SPA1650 SPA1657 1650 1657 SPB4250MN SPB4500MN SPB4250 SPB4500 4250 4500 SPA1682MN SPA1682 1682 SPB4750MN SPB4750 4750 SPA1700MN SPA1700 1700 SPB4820 4820 SPA1707MN SPA1707 1707 SPB4870 4870 SPA1732MN SPA1750MN SPA1732 SPA1750 1732 1750 SPB5000 SPB5300 5000 5300 SPA1757MN SPA1757 1757 SPB5600 5600 SPA1782MN SPA1782 1782 SPB6000 6000 SPA1800MN SPA1800 1800 SPB6300 6300 SPA1807MN SPA1832MN SPA1807 SPA1832 1807 1832 SPB6700 6700 SPB7100 7100 SPB7500 SPB8000 7500 8000 SPA3150MN SPA4000MN ® Super HV (MN) ordering code is composed as follow: SPZ560(MN) SPZ Section 560 Datum length (mm) (MN) Moulded notch SPB1900MN SPB2000MN SPB2020MN SPB2120MN SPB2150MN SPB2240MN SPB4000MN SPC10000 SPC10600 SPC11200 SPC11800 SPC12000 SPC12500 SPC13500 SPC13800 SPC14200 SPC15000 SPC16500 Recommended minimum pulley diameter Pulley Profile diameter,mm Moulded SPZ 56 notch(MN) Wrapped 71 Moulded SPA 80 notch(MN) Wrapped 100 Moulded SPB 112 notch(MN) Wrapped 160 Moulded SPC 180 notch(MN) Wrapped 250 Ld = Lp Ld = Datum Lenght Lp = Pitch Lenght LI = Inside Lenght 9 V- Belts and V- Belt Pulleys Chapter 11 Classical V- belt Z Wrapped, classical section V- belt VulcoPower™ V- belts are built for a reliable and durable performance on heavy- duty industrial drives. They offer a combination of advantages only available in Gates quality belts –all at an attractive price. Identification Durable white marking indicating type and dimensions. Construction Belt compound converts forces on the sidewalls into longitudinal forces in the tensile member. Textile cover provides grip and protects against abrasion. Polyester tensile member withstands occasional or recurrent shockloads. Excellent resistance to oil, heat, ozone, sunlight, weather and ageing. Static conductive (ISO 1813) and can as such be used in the conditions described in the Directive 94/9/ EC - ATEX. Advantages Excellent performance/ cost ratio. Manufactured by Gates according to the highest quality standards. Suited for a wide range of light- to medium- duty power transmission applications and motion transfer. Available in all popular lengths and sections Match system: all sizes meet Gates UNISET tolerances, they can be installed without matching. Sections and nominal dimensions Width mm Height mm Z 10 6 A 13 8 B 17 11 C 22 14 Recommended minimum pulley diameter Profile Pulley diameter,mm Z 60 A 85 B 112 C 180 D 315 Description Z16 Z17.5 Z18.5 Z19.5 Z20.5 Z22.5 Z24 Z25 Z25.5 Z26.5 Z28 Z29 Z30 Z31 Z32.5 Z33.5 Z34.5 Z36 Z37.5 Z38.5 Z39.5 Z41.5 Z44 Z45 Z46 Z47 Z48 Z49 Z50 Z51 Z52 Z53 Z54 Z55 Z57 Z59 Z60 Z61 Z63 Z65 Z66 Z67 Z69 Z71 Inside length mm 413 438 478 493 518 568 613 628 653 668 703 733 768 788 828 853 878 913 948 978 998 1048 1130 1143 1178 1198 1223 1243 1273 1305 1323 1340 1373 1398 1448 1498 1523 1553 1603 1653 1678 1703 1753 1803 A Datum length mm 435 460 500 515 540 590 635 650 675 690 725 755 790 810 850 875 900 935 970 1000 1020 1070 1152 1165 1200 1220 1245 1265 1295 1327 1345 1362 1395 1420 1470 1520 1545 1575 1625 1675 1700 1725 1775 1825 Description A18 A19 A20 A21 A22 A23 A24 A25 A26 A27.5 A28.5 A29.5 A30 A31 A32 A32.5 A33 A34 A35 A36 A37 A38 A39 A40 A41 A42 A43 A44 A45 A46 A47 A48 A49 A50 A51 A52 A53 A54 A55 A56 A57 A58 A59 A60 A61 A62 A63 A64 A65 A66 A67 A68 A69 A70 A71 A72 A73 A74 A75 A76 A77 A78 A79 A80 A81 A82 A83 A84 A85 Inside length mm 460 475 525 540 565 590 610 633 670 700 715 750 770 795 805 825 845 870 890 915 945 962 980 1015 1040 1065 1090 1115 1145 1175 1190 1225 1248 1265 1300 1325 1355 1370 1410 1425 1455 1475 1495 1530 1550 1580 1615 1625 1660 1676 1700 1725 1750 1780 1805 1830 1855 1885 1910 1930 1960 1980 2010 2035 2060 2085 2110 2135 2170 Datum length mm 490 505 555 570 595 620 640 663 700 730 745 780 800 825 835 855 875 900 920 945 975 992 1010 1045 1070 1095 1120 1145 1175 1205 1220 1255 1278 1295 1330 1355 1385 1400 1440 1455 1485 1505 1525 1560 1580 1610 1645 1655 1690 1706 1730 1755 1780 1810 1835 1860 1885 1915 1940 1960 1990 2010 2040 2065 2090 2115 2140 2165 2200 Description A86 A87 A88 A89O A90 A91 A92 A93 A94 A95 A96 A97 A98 A100 A102 A104 A105 A107 A108 A110 A112 A115 A116 A118 A120 A124 A128 A130 A132 A136 A140 A144 A148 A158 A167 A187 A197 Inside length mm 2190 2215 2240 2265 2290 2315 2340 2365 2390 2415 2445 2465 2500 2540 2590 2650 2680 2720 2745 2800 2855 2920 2950 3000 3055 3150 3255 3305 3350 3455 3555 3660 3750 4015 4245 4750 5000 Datum length mm 2220 2245 2270 2295 2320 2345 2370 2395 2420 2445 2475 2495 2530 2570 2620 2680 2710 2750 2775 2830 2885 2950 2980 3030 3085 3180 3285 3335 3380 3485 3585 3690 3780 4045 4275 4780 5030 10 V- Belts and V- Belt Pulleys Chapter 11 B Inside Description length Description B26 B27 690 B28 B26 710 B29 B27 730 B30 B28 750 B31 B29 795 B32 B30 820 B33 B31 860 B35 B32 890 B36 B33 930 B37 B35 950 B38 B36 970 B39 B37 1000 B40 B38 1025 B41 B39 1045 B42 B40 1070 B43 B41 1105 B44 B42 1110 B45 B43 1145 B46 B44 1170 B47 B45 1195 B48 B46 1225 B49 B47 1250 B50 B48 1278 B51 B49 1300 B52 B50 1325 B53 B51 1350 B54 B52 1380 B55 B53 1410 B56 B54 1440 B57 B55 1460 B58 B56 1480 B59 B57 1510 B60 B58 1525 B61 B59 1555 B62 B60 1575 B63 B61 1595 B64 B62 1630 B65 B63 1650 B66 B64 1695 B67 B65 1715 B68 B66 1730 B69 B67 1755 B70 B68 1780 B71 B69 1810 B72 B70 1835 B73 B71 1855 B74 B72 1885 B75 B73 1905 B76 B74 1935 B77 B75 1960 B78 B76 2000 B80 B77 2030 B81 B78 2060 B82 B80 2090 B83 B81 2115 B84 B82 2140 B85 B83 2165 B86 B84 2185 B87 B85 2215 B88 B86 2240 B89 B87 2255 B90 B88 2290 B91 B89 2310 B92 B90 2340 B93 B91 2365 B94 B92 2395 B95 B93 2420 B94 B95 Datum mm Inside Datum mm length length length 650 690 mm mm 730 650 690 750 690 730 770 710 750 790 730 770 835 750 790 860 795 835 900 820 860 930 860 900 970 890 930 990 930 970 1010 950 990 1040 970 1010 1065 1000 1040 1085 1025 1065 1110 1045 1085 1145 1070 1110 1150 1105 1145 1185 1110 1150 1210 1145 1185 1235 1170 1210 1265 1195 1235 1290 1225 1265 1318 1250 1290 1340 1278 1318 1365 1300 1340 1390 1325 1365 1420 1350 1390 1450 1380 1420 1480 1410 1450 1500 1440 1480 1520 1460 1500 1550 1480 1520 1565 1510 1550 1595 1525 1565 1615 1555 1595 1635 1575 1615 1670 1595 1635 1690 1630 1670 1735 1650 1690 1755 1695 1735 1770 1715 1755 1795 1730 1770 1820 1755 1795 1850 1780 1820 1875 1810 1850 1895 1835 1875 1925 1855 1895 1945 1885 1925 1975 1905 1945 2000 1935 1975 2040 1960 2000 2070 2000 2040 2100 2030 2070 2130 2060 2100 2155 2090 2130 2180 2115 2155 2205 2140 2180 2225 2165 2205 2255 2185 2225 2280 2215 2255 2295 2240 2280 2330 2255 2295 2350 2290 2330 2380 2310 2350 2405 2340 2380 2435 2365 2405 2460 2395 2435 2420 2460 C Description B96 B97 B98 B99 B100 B101 B102 B103 B104 B105 B106 B108 B110 B112 B114 B115 B116 B118 B120 B124 B126 B128 B130 B132 B134 B136 B140 B144 B147 B148 B152 B154 B158 B162 B167 B173 B175 B180 B187 B192 B195 B210 B240 B248 B270 B280 Inside length Datum length mm 2485 2510 2535 2560 2585 2610 2635 2655 2685 2715 2740 2790 2840 2890 2940 2965 2990 3040 3095 3190 3250 3300 3350 3395 3450 3500 3600 3705 3780 3800 3905 3955 4060 4160 4295 4440 4490 4620 4795 4920 5000 5380 6130 6340 6865 7140 mm 2445 2470 2495 2520 2545 2570 2595 2615 2645 2675 2700 2750 2800 2850 2900 2925 2950 3000 3055 3150 3210 3260 3310 3355 3410 3460 3560 3665 3740 3760 3865 3915 4020 4120 4255 4400 4450 4580 4755 4880 4960 5340 6090 6300 6825 7100 Ld = Lp Ld = Datum Lenght Lp = Pitch Lenght LI = Inside Lenght VulcoPower™ ordering code is composed as follows: C43 C - Section 43 - Inside lenght in inch Description C43 C46 C48 C49 C51 C52 C53 C55 C56 C57 C58 C59 C60 C61 C62 C63 C65 C66 C67 C68 C69 C70 C71 C72 C75 C76 C77 C78 C80 C81 C82 C83 C84 C85 C86 C88 C89 C90 C93 C94 C95 C96 C97 C98 C99 C10 C101 C102 C104 C105 C106 C108 C110 C112 C114 C115 C116 C118 C120 C122 C124 C128 C130 C132 C134 C136 C140 C144 Inside length Datum length mm 1150 1250 1285 1310 1350 1395 1410 1460 1485 1510 1550 1570 1585 1625 1650 1675 1725 1750 1775 1800 1825 1850 1875 1900 1970 2000 2030 2050 2100 2125 2150 2180 2200 2230 2255 2300 2330 2355 2425 2445 2470 2490 2525 2560 2595 2615 2640 2660 2715 2740 2765 2820 2860 2915 2975 2990 3020 3055 3120 3185 3215 3320 3370 3425 3460 3535 3615 3730 mm 1092 1192 1227 1252 1292 1337 1352 1402 1427 1452 1492 1512 1527 1567 1592 1617 1667 1692 1717 1742 1767 1792 1817 1842 1912 1942 1972 1992 2042 2067 2092 2122 2142 2172 2197 2242 2272 2297 2367 2387 2412 2432 2467 2502 2537 2557 2582 2602 2657 2682 2707 2762 2802 2857 2917 2932 2962 2997 3062 3127 3157 3262 3312 3367 3402 3477 3557 3672 Description C148 C153 C158 C162 C165 C167 C170 C173 C177 C180 C187 C190 C195 C197 C204 C208 C210 C222 C225 C238 C240 C250 C265 C270 C280 Inside length Datum length mm 3830 3960 4065 4180 4270 4320 4400 4465 4565 4645 4810 4880 5025 5080 5250 5360 5400 5665 5730 6060 6120 6365 6760 6880 7165 mm 3772 3902 4007 4122 4212 4262 4342 4407 4507 4587 4752 4822 4967 5022 5192 5302 5342 5607 5672 6002 6062 6307 6702 6822 7107 D D98 D104 D110 D112 D120 D124 D128 D137 D140 D144 D158 D162 D170 D173 D177 D180 D187 D195 D197 D204 D210 D223 D240 D250 D270 D282 D298 D300 D315 D316 D330 D345 D360 D390 D420 D441 D450 D480 D540 D600 D660 2500 2650 2800 2850 3050 3150 3250 3480 3550 3660 4000 4115 4320 4400 4500 4570 4750 4955 5000 5180 5335 5600 6030 6300 6800 7100 7500 7555 8007 7967 8320 8770 9080 9910 10672 11207 11435 12197 13721 15246 16771 2570 2720 2875 2925 3130 3230 3330 3560 3635 3740 4095 4195 4400 4475 4575 4650 4830 5035 5085 5260 5415 5680 6115 6365 6875 7180 7585 7635 8082 8042 8400 8845 9160 9982 10747 11282 11510 12272 13796 15321 16846 11 V- Belts and V- Belt Pulleys Chapter 11 Hi- power Dubl- V Hi- Power® Dubl- V Wrapped, classical section, double Gates’ Hi- Power® Dubl- V belt is characterised by a double- V profile. It uses flex- bonded tensile cords, which are highly resistant to flexing forces, and a protective Flex- Weave® cover. It is the ideal solution for “serpentine” drives (drives with counterrotating shafts) where power is transmitted from both the top and the bottom of the belts. Recommended minimum pulley diameter ProfilePulley diameter,mm AA 100 BB 160 CC 250 DD 315 Sections and nominal dimensions AA Datum lenght BB Description Effective lenght Effective lenght Datum lenght mm mm AA51 1350 1330 BB35 mm mm 965 AA55 1450 1435 AA60 1575 1560 BB38 BB42 AA64 1678 1663 AA68 1780 AA75 Effective lenght mm mm 940 CC75 2010 1980 1040 1015 CC81 2165 2130 1140 1120 CC85 2265 2230 BB43 1165 1145 CC90 2395 2360 1765 BB45 1215 1195 CC96 2545 2510 1960 1940 BB46 1240 1220 CC105 2775 2740 AA80 2085 2070 BB51 1370 1345 CC112 2950 2920 AA85 2210 2195 BB53 1420 1395 CC120 3155 3120 AA86 2237 2222 BB55 1470 1450 CC128 3360 3325 AA88 2288 2273 BB60 1600 1575 CC136 3560 3525 AA90 2340 2325 BB66 1750 1730 CC144 3765 3730 AA92 2390 2375 BB68 1800 1780 CC158 4120 4085 AA96 2490 2475 BB71 1880 1855 CC162 4220 4190 AA105 2720 2705 BB73 1925 1905 CC173 4500 4465 AA112 2900 2880 BB74 1955 1930 CC180 4680 4645 AA120 3100 3085 BB75 1980 1955 CC195 5060 5025 AA128 3305 3290 BB81 2130 2110 CC210 5440 5405 BB83 2185 2160 CC240 6150 6120 BB85 2235 2210 CC250 6382 6350 BB90 2360 2335 CC270 6915 6880 BB92 2410 2390 CC300 7675 7640 BB93 2435 2415 CC330 8440 8405 BB94 2460 2440 CC360 9200 9165 BB95 2485 2465 BB96 2510 2490 CC390 CC420 9960 10725 9930 10690 BB97 2535 2515 BB100 2615 2595 BB105 2740 2720 BB107 2790 2770 BB108 2815 2795 BB111 2895 2870 BB112 2920 2895 BB116 3020 3000 BB118 3070 3050 BB120 3120 3100 BB122 3170 3150 BB123 3195 3175 BB124 3220 3200 BB127 3300 3275 BB128 3325 3300 BB129 3350 3325 BB130 3375 3350 BB136 3528 3505 BB140 3629 3610 BB144 3730 3710 BB155 4010 3990 BB158 4085 4065 BB168 4340 4320 Width mm Height mm AA 13 8 BB 17 11 CC 22 14 BB169 4365 4345 DD 32 19 BB173 4470 4445 BB180 4645 4625 BB190 4900 4880 BB195 5025 5005 BB210 5410 5385 BB226 5814 5755 BB228 5864 5805 BB230 5915 5855 BB240 6130 6110 BB270 6895 6870 BB277 BB300 7070 7655 7050 7635 Hi- Power® Dubl- V ordering code is composed as follows: AA51 AA - Section (double) 51 - Lenght in inch All dimensions are available on request. CC Description Desctription DD Effective Description lenght Datum lenght Datum lenght mm mm DD270 6925 6875 DD300 DD360 7690 9215 7635 9160 12 V- Belts and V- Belt Pulleys Chapter 11 Heavy Duty V- Belts Wrapped, narrow section multiple V- belt PREDATOR® These belts are unique in extreme robustness and high load carrying capability that performs well in harsh environments and in extremely demanding applications where standard Vbelts have performance issues. The difference is in the construction: they have the highest power density of any Vbelt and virtually zero stretch because of the use of high strength, high modulus aramid tensile cords. Identification Durable silver marking indicating type and dimensions. Construction Aramid tensile cords provide extraordinary strength, durability and virtually zero stretch. Double fabric cover offers extreme abrasion and wear resistance. Specially treated extra tough cover withstands slip and shear forces at peak loads without generating excessive heat and resists penetration by foreign materials. Chloroprene rubber compounds provide superb oil and heat resistance. Non- rubber surfaced cover allows momentary slippage due to excessive overloads without damaging the belt. Advantages At least 40% higher power ratings than standard construction V- belts. No need for constant belt re- tensioning. Less maintenance, less downtime. Excellent problem solver. Available in PowerBand® and single belt construction: - PowerBand® belts feature a multiple layer tie band that provides excellent lateral rigidity to prevent belts from turning over or from coming off the drive. - Single belts can be used for applications where PowerBand® belts are not an option. Predator® single belts are available on demand in lengths over 1400 mm. Predator® PowerBand® belts are static conductive (ISO 1813) (except for 8VP) and can as such be used in the conditions described in the Directive 94/9/ EC - ATEX; for detailed info on the static conductivity of Predator® single belts, please contact your Gates representative Sections and nominal dimensions Pitch mm Width mm Height mm SPBP 19,0 16 13 SPBP 2 ? 16 SPCP 25,5 22 18 SPCP 2 ? 12 9JP 10,3 10 8 9JP 2 ? 30 15JP 17,5 16 13 15JP 2 ? 8VP 28,6 26 23 8VP 3 ? Available number of ribs Recommended minimum pulley diameter Profile Pulley diameter,mm 9JP 71 16 SPBP,151JP 160 5 SPCP 250 8VP 315 14 V- Belts and V- Belt Pulleys SPBP Chapter 11 SPCP Description Datum lenght SPBP2120 SPBP2240 SPBP2360 SPBP2500 SPBP2650 SPBP2800 SPBP3000 SPBP3150 SPBP3350 SPBP3550 SPBP3750 SPBP4000 SPBP4250 SPBP4500 SPBP4750 SPBP5000 SPBP5300 SPBP5600 SPBP6000 SPBP6300 SPBP6700 SPBP7100 SPBP7500 SPBP8000 mm 2120 2240 2360 2500 2650 2800 3000 3150 3350 3550 3750 4000 4250 4500 4750 5000 5300 5600 6000 6300 6700 7100 7500 8000 9JP Description Datum lenght SPCP3000 SPCP3150 SPCP3350 SPCP3750 SPCP4000 SPCP4250 SPCP4500 SPCP4750 SPCP5000 SPCP5300 SPCP5600 SPCP6000 SPCP6300 SPCP6700 SPCP7100 SPCP7500 SPCP8000 SPCP8500 SPCP9000 SPCP10000 SPCP10600 SPCP11200 mm 3000 3150 3350 3750 4000 4250 4500 4750 5000 5300 5600 6000 6300 6700 7100 7500 8000 8500 9000 10000 10600 11200 15JP Description Effective lenght 9JP1400 9JP1500 9JP1600 9JP1700 9JP1800 9JP1900 9JP2000 9JP2120 9JP2240 9JP2360 9JP2500 9JP2650 9JP2800 9JP3000 9JP3150 9JP3350 9JP3550 mm 1400 1500 1600 1700 1800 1900 2000 2120 2240 2360 2500 2650 2800 3000 3150 3350 3550 8VP Description Effective lenght 8VP1000 8VP1060 8VP1120 8VP1180 8VP1250 8VP1320 8VP1400 8VP1500 8VP1600 8VP1700 8VP1800 8VP1900 8VP2000 8VP2120 8VP2240 8VP2360 8VP2500 8VP2650 8VP2800 8VP3000 8VP3150 8VP3350 8VP3550 8VP3750 8VP4000 8VP4250 8VP4500 8VP4750 8VP5000 8VP5600 8VP6000 mm 2540 2690 2845 2995 3175 3355 3555 3810 4065 4320 4570 4825 5080 5385 5690 5995 6350 6730 7110 7620 8000 8510 9015 9525 10160 10795 11430 12065 12700 14225 15240 Description Effective lenght 15JP1400 15JP1500 15JP1600 15JP1700 15JP1800 15JP1900 15JP2000 15JP2120 15JP2240 15JP2360 15JP2500 15JP2650 15JP2800 15JP3000 15JP3150 15JP3350 15JP3550 15JP3750 15JP4000 15JP4250 15JP4500 15JP4750 15JP5000 15JP5300 15JP5600 15JP6000 15JP6300 15JP6700 15JP7100 15JP7500 15JP8000 15JP8500 15JP9000 mm 1400 1500 1600 1700 1800 1900 2000 2120 2240 2360 2500 2650 2800 3000 3150 3350 3550 3750 4000 4250 4500 4750 5000 5300 5600 6000 6300 6700 7100 7500 8000 8500 9000 Predator® ordering code is composed as follows: SPBP3350/3 SPBP - Section 3350 - Datum lenght (mm) 3 - Number of ribs 15 V- Belts and V- Belt Pulleys Chapter 11 Heavy duty V- belts Raw egde, moulded notch, narrow section multiple V- belt Quad- Power® II PowerBand® Quad- Power® II PowerBand® offers a stable position in the pulleys and a smooth running solution for drives where single belts vibrate. It consists of several V- belts joined together by a permanent, high strength tie band, thus being tougher than all the belts taken separately. Quad- Power® II PowerBand® is easy to install and offers a high resistance to vibrations. Identification Durable marking indicating type and dimensions. Construction Recommended minimum pulley diameter Profile Pulley diameter,mm XPZ,3VX 56 XPA 80 XPB,5VX 112 Strong band controls belt- to- belt distance and prevents sideways bending. Flex- bonded tensile cords are vulcanised as one solid unit making the belt highly resistant to tensile and flexing forces, fatigue and shock loads. Flat back construction reduces noise when used with a back side idler or tensioner. Elastomeric compound protects the belt against heat, ozone and sunlight. Static conductive (ISO 1813) and can as such be used in the conditions described in the Directive 94/9/ EC - ATEX. Advantages Sections and nominal dimensions Pitch mm Width mm Height mm 3VX 10,3 10 8 5VX 17,5 16 13 XPZ 12,0 10 8 XPA 15,0 13 10 XPB 19,0 16 13 High stability and smooth running on the toughest drives. Better resistance to vibrations. Temperature ranges from -30°C to +60°C (higher temperatures for shorter periods). Important design economies possible. Savings in drive space and weight thanks to high transmission efficiency. Match system: all sizes meet Gates UNISET tolerances, they can be installed without matching. Available number of ribs 2 3 4 5 3VX x x x x 5VX x x x x XPZ x x x XPA x x XPB x x 16 V- Belts and V- Belt Pulleys 3VX Chapter 11 XPZ Description Effective lenght RMA XPA Description Effective lenght mm ISO 3VX250 635 XPZ800 3VX265 675 3VX280 3VX300 XPB Description Effective lenght mm ISO mm ISO mm 800 XPA800 800 XPB1250 1250 XPZ850 850 XPA850 850 XPB1320 1320 710 XPZ900 900 XPA900 900 XPB1400 1400 760 XPZ950 950 XPA950 950 XPB1450 1450 3VX315 800 XPZ1000 1000 XPA1000 1000 XPB1500 1500 3VX335 850 XPZ1030 1030 XPA1030 1030 XPB1550 1550 3VX355 900 XPZ1060 1060 XPA1060 1060 XPB1600 1600 3VX375 950 XPZ1090 1090 XPA1090 1090 XPB1650 1650 3VX400 1015 XPZ1120 1120 XPA1120 1120 XPB1700 1700 3VX425 1080 XPZ1150 1150 XPA1150 1150 XPB1750 1750 3VX450 1145 XPZ1180 1180 XPA1180 1180 XPB1800 1800 3VX475 1205 XPZ1212 1212 XPA1250 1250 XPB1850 1850 3VX500 1270 XPZ1250 1250 XPA1320 1320 XPB1900 1900 3VX530 1345 XPZ1270 1270 XPA1360 1360 XPB1950 1950 3VX560 1420 XPZ1320 1320 XPA1400 1400 XPB2000 2000 3VX600 1525 XPZ1340 1340 XPA1450 1450 XPB2120 2120 3VX630 1600 XPZ1362 1362 XPA1500 1500 XPB2150 2150 3VX670 1700 XPZ1400 1400 XPA1550 1550 XPB2240 2240 3VX710 1805 XPZ1420 1420 XPA1600 1600 XPB2280 2280 3VX750 1905 XPZ1450 1450 XPA1650 1650 XPB2360 2360 3VX800 2030 XPZ1500 1500 XPA1700 1700 XPB2410 2410 3VX850 2160 XPZ1550 1550 XPA1750 1750 XPB2500 2500 3VX900 2285 XPZ1600 1600 XPA1800 1800 XPB2530 2530 3VX950 2415 XPZ1650 1650 XPA1850 1850 XPB2650 2650 3VX1000 2540 XPZ1700 1700 XPA1900 1900 XPB2680 2680 3VX1060 2690 XPZ1750 1750 XPA1950 1950 XPB2800 2800 3VX1120 2845 XPZ1800 1800 XPA2000 2000 XPB2840 2840 3VX1180 2995 XPZ1850 1850 XPA2060 2060 XPB3000 3000 3VX1250 3175 XPZ1900 1900 XPA2120 2120 XPB3150 3150 3VX1320 3355 XPZ1950 1950 XPA2240 2240 XPB3350 3350 3VX1400 3555 XPZ2000 2000 XPA2360 2360 XPB3550 3550 XPZ2030 2030 XPA2430 2430 XPB3750 3750 XPZ2120 2120 XPA2500 2500 XPB4000 4000 XPZ2160 2160 XPA2650 2650 XPB4250 4250 XPZ2240 2240 XPA2800 2800 XPB4500 4500 XPZ2360 2360 XPA3000 3000 XPB4750 4750 XPZ2500 2500 XPA3150 3150 5VX Description Effective lenght 5VX500 1270 5VX530 1345 5VX560 1420 5VX600 1525 5VX630 1600 5VX670 1700 XPZ2650 2650 XPA3350 3350 5VX710 1805 XPZ2800 2800 XPA3550 3550 5VX750 1905 XPZ3000 3000 XPA3750 3750 5VX800 2030 5VX850 2160 XPZ3150 3150 XPA4000 4000 5VX900 2285 XPZ3350 3350 5VX950 2415 XPZ3550 3550 5VX1000 2540 5VX1060 2690 5VX1120 2845 Quad- Power® II PowerBand® ordering code is composed as follows: 5VX1180 2995 5VX1250 3175 XPA1030/2 5VX1320 3355 XPA - Section 5VX1400 3555 1030 - Datum lenght (mm) 5VX1500 3810 5VX1600 4065 2 - Number of ribs 5VX1700 4320 5VX1800 4570 5VX1900 5VX2000 4825 5080 17 V- Belts and V- Belt Pulleys Chapter 11 Heavy duty V- belts SPB Wrapped, narrow section/ classical section multiple V- belt Super HC® & Hi- Power® Powerband® Gates Super HC® PowerBand® and Hi- Power® PowerBand® offer a solution for drives where single belts vibrate, turn over or jump off the pulleys. They consist of several V- belts joined together by a permanent, high strength tie band, thus being tougher than all the belts taken separately. Super HC® PowerBand® is available in SPB, SPC, 8V/25J, 9J and 15J sections. Hi- Power® B, C and D Identification Durable marking indicating type and dimensions. Construction Strong band controls belt- to- belt distance and prevents sideways bending. Flex- bonded tensile cords are vulcanised as one solid unit making the belt highly resistant to tensile and flexing forces, fatigue and shock loads. Concave sides and arched top. Flex- Weave® cover protects the belt core from the toughest environments. Elastomeric compound protects the belt against heat, ozone and sunlight. Static conductive (ISO 1813) and can as such be used in the conditions described in the Directive 94/9/ EC - ATEX. Advantages SPC Description Datum lenght Description Datum lenght SPB2120 2120 SPC3000 3000 SPB2240 2240 SPC3150 3150 SPB2360 2360 SPC3350 3350 SPB2500 2500 SPC3550 3550 SPB2650 2650 SPC3750 3750 SPB2800 2800 SPC4000 4000 SPB3000 3000 SPC4250 4250 SPB3150 3150 SPC4500 4500 SPB3350 3350 SPC4750 4750 SPB3550 3550 SPC5000 5000 SPB3750 3750 SPC5300 5300 SPB4000 4000 SPC5600 5600 SPB4250 4250 SPC6000 6000 SPB4500 4500 SPC6300 6300 SPB4750 4750 SPC6700 6700 SPB5000 5000 SPC7100 7100 SPB5300 5300 SPC7500 7500 SPB5600 5600 SPC8000 8000 SPB6000 6000 SPC8500 8500 SPB6300 6300 SPC9000 9000 SPB6700 6700 SPC10000 10000 SPB7100 7100 SPB7500 SPB8000 7500 8000 SPC10600 SPC11200 10600 11200 mm Better resistance to vibrations. High stability and smooth running on the toughest drives. Temperature ranges from -30°C to +60°C. Important design economies possible. Savings in drive space and weight thanks to high transmission efficiency. Sections and nominal dimensions Width mm Height mm SPB 19,00 16 13 SPC 25,50 22 18 9J3V 10,30 10 8 15J/5V 17,50 16 13 25J/8V 28,60 26 23 B 19,05 17 10 C 25,40 22 12 D 36,50 32 19 Super HC® Hi- Power® 9J/3V Description Datum lenght 9J1250 1250 9J1320 1320 9J1400 1400 9J1500 1500 9J1600 1600 9J1700 1700 9J1800 1800 9J1900 1900 9J2000 2000 9J2120 2120 9J2240 2240 9J2360 2360 9J2500 2500 9J2650 2650 9J2800 2800 9J3000 3000 9J3150 3150 9J3350 9J3550 3350 3550 mm Recommended minimum pulley diameter Profile Pulley diameter,mm 9J,3V 71 B 112 SPB,15J,5V 160 C 180 SPC 250 25J,8V,D 315 Pitch mm mm Available number of ribs Super HC® SPB 2 → 16 SPC 2 → 12 9J/3V 2 → 30 15J/5V 2 → 16 25J/8V 3 → 5 B 2 → 5 C 2 → 5 D 34 → 5 Hi- Power® 18 V- Belts and V- Belt Pulleys 15J/5V Description 15J1250 15J1320 15J1400 15J1500 15J1600 15J1700 15J1800 15J1900 15J2000 15J2120 15J2240 15J2360 15J2500 15J2650 15J2800 15J3000 15J3150 15J3350 15J3550 15J3750 15J4000 15J4250 15J4500 15J4750 15J5000 15J5300 15J5600 15J6000 15J6300 15J6700 15J7100 15J7500 15J8000 15J8500 15J9000 Effective length mm 1250 1320 1400 1500 1600 1700 1800 1900 2000 2120 2240 2360 2500 2650 2800 3000 3150 3350 3550 3750 4000 4250 4500 4750 5000 5300 5600 6000 6300 6700 7100 7500 8000 8500 9000 25J/8V Description 8V1000 8V1060 8V1120 8V1180 8V1250 8V1320 8V1400 8V1500 8V1600 8V1700 8V1800 8V1900 8V2000 8V2120 8V2240 8V2360 8V2500 8V2650 8V2800 8V3000 8V3150 8V3350 8V3550 8V3750 8V4000 8V4250 8V4500 8V4750 8V5000 8V5600 8V6000 Effective length mm 2540 2692 2845 2997 3175 3355 3556 3810 4064 4318 4572 4826 5080 5385 5690 5994 6350 6731 7112 7620 8001 8509 9017 9525 10160 10795 11430 12065 12700 14224 15240 Chapter 11 B Description B35 B38 B42 B43 B46 B48 B50 B51 B52 B53 B54 B55 B56 B57 B58 B59 B60 B61 B62 B63 B64 B65 B66 B67 B68 B70 B71 B72 B73 B74 B75 B77 B78 B79 B80 B81 B82 B83 B84 B85 B86 B87 B88 B90 B92 B93 B94 B95 B96 B97 B99 B100 B103 B105 B108 B110 B Effective length mm 935 1011 1113 1138 1214 1265 1316 1341 1367 1392 1417 1443 1468 1494 1519 1544 1570 1595 1621 1646 1671 1697 1722 1748 1773 1824 1849 1875 1900 1925 1951 2002 2027 2052 2078 2103 2129 2154 2180 2205 2230 2256 2281 2332 2383 2408 2434 2459 2484 2510 2560 2586 2662 2713 2789 2840 D Effective length mm 2891 3094 3195 3297 3424 3500 3780 3805 3957 4059 4161 4440 4618 4999 5380 5723 6104 6485 6866 7628 8009 Description B112 B120 B124 B128 B133 B136 B144 B148 B154 B158 B162 B173 B180 B195 B210 B225 B240 B255 B270 B300 B315 Description D120 D144 D158 D173 D180 D195 D210 D225 D240 D255 D270 D285 D300 D315 D330 D345 D360 D390 D420 D450 D480 D540 D600 D660 C Description C60 C68 C75 C81 C85 C90 C96 C99 C100 C105 C108 C109 C112 C120 C124 C128 C136 C144 C158 C162 C173 C180 C195 C210 C225 C240 C255 C270 C285 C300 C315 C330 C345 C360 C390 C420 Effective length mm 1598 1801 1979 2131 2233 2360 2512 2588 2614 2741 2817 2842 2918 3122 3223 3325 3528 3731 4087 4188 4468 4646 5027 5408 5738 6119 6500 6881 7262 7643 8024 8405 8786 9167 9929 10688 Effective length mm 3132 3741 4097 4478 4656 5037 5418 5735 6116 6497 6878 7259 7640 8021 8402 8783 9164 9926 10688 11450 12212 13736 15260 16784 Super HC® PowerBand® ordering code is composed as follows: 9J1250/2 9J - Section 1250 - Effective length(mm) 2 - Number of ribs NOTES * Dimensions according to ISO 4184. 9J / 15J / 25J are ISO standards for RMA 3V- PB / 5V- PB / 8V- PB. 8V PowerBand® belts are designed for use both in 8V and 25J pulleys. 19 V- Belts and V- Belt Pulleys Chapter 11 V- belts for Variable Speed Drives Wide raw edge V- belt Multi- Speed® Multi- Speed™ belt provides top performance on variable speed drives. It adjusts itself to the pulley groove without difficulty, providing a wide range of speeds and speed ratios. In addition to the standard Multi- Speed™ belt line, special sizes (top width, thickness and angle) are available on request. Identification Durable marking plus printed size. Construction Engineered notch contour increases flexibility. The notches ensure maximum heat dispersion, considerably decreasing running temperatures. Strong transverse rigidity offers high resistance to distorsion of the belt in the pulley. This results in even load distribution and wear reduction. Uniform composition and thickness of the undercord ensure smooth and silent running. Combination of these construction features gives maximum speed adjustment. Advantages Maximum range of speed changes. High stability and smooth running on the toughest drives. Smooth machine operation. Exceptionally long belt life. Reference Top width (mm) Thickness (mm) Angle Special Gates sizes Inside lenght: mm 13 13 6 26° 600 700 800 900 23 23 8 26° 525 600 650 700 750 800 850 900 950 1000 1060 1120 1180 1250 1320 1400 1500 28 28 9 26° 650 700 750 800 850 900 950 1000 1060 1120 1180 1250 1320 1400 1500 1600 37 37 10 28° 800 850 900 950 1000 1060 1120 1180 1250 1320 1400 1500 1600 1700 1800 2000 2240 ISO R 1604 sizes Datum length: mm 47 47 13 28° 1000 1060 1120 1180 1250 1320 1400 1500 1600 1700 1800 2000 2240 W16 17 6 24° 630 710 800 900 1000 W20 21 7 26° 630 710 800 900 1000 1120 1250 W25 26 8 26° 710 800 900 1000 1120 1250 1400 1600 W31,5 33 10 26° 900 1000 1120 1250 1400 1600 1800 2000 W40 42 13 28° 1120 1250 1400 1600 1700 1800 2000 2240 2500 W50 52 16 28° 1400 1600 1800 2000 2240 2500 2800 3150 W63 65 20 30° 1800 2000 2240 2500 2800 Multi- Speed® ordering code iscomposed as follows: W16-630 W16 - Standardised cross- section 630 - Datum lenght (mm) 23X8-600 23 - Standardised cross- section X8 - Thickness (mm) 600 - Inside lenght (mm) 21 V- Belts and V- Belt Pulleys Chapter 11 V- belts for Compact Drives Polyurethane V- belt Polyflex® This compact and strong belt with nominal top width from 3 mm to 11 mm transmits more power and allows high speed ratios. Polyflex® is suited for extremely small diameter pulleys and very compact drives with high rotational speeds. Ideal for use on machines and machine tools requiring high performance and smooth operation in limited space such as bench type milling machines, lathe drives, woodworking and metalworking machine spindle drives, computer peripheral equipment, small blowers, etc. Identification Durable marking indicating type and dimension. Construction Polyurethane compound, superior to conventional belt materials, offers high fatigue and wear resistance and a high friction coefficient. It also improves adhesion to the tensile cords. Polyurethane is extremely resistant to heat, chemicals and oil. Uniformity throughout Polyflex® is ensured because the polyurethane compound is not layered but cast as a single unit after the positioning of the tensile cords in the mould. Ribbed top provides lateral rigidity without increasing bending stresses. The ribs also help to keep Polyflex® belts running cool. 60° angle results in better support of the tensile section, and provides a more even load distribution. Advantages Design freedom and space savings which are not possible with conventional rubber construction belts. Low maintenance cost as belt needs less re- tensioning. Long belt life on compact drives. Temperature ranges from -54°C up to +85°C. Sections and nominal dimensions Width mm Height mm 3M 3 2,28 5M 5 3,30 7M 7 5,33 11M 11 6,85 Recommended minimum pulley diameter Profile Pulley diameter,mm 3M 17 5M 26 7M 42 11M 67 22 V- Belts and V- Belt Pulleys 3M Description Chapter 11 5M Effective lenght Description mm 7M Effective lenght Description mm 11M Effective lenght Description Effective lenght mm mm 3M180 180 5M280 280 7M500 500 11M710 710 3M185 185 5M290 290 7M515 515 11M730 730 3M190 190 5M300 300 7M530 530 11M750 750 3M195 195 5M307 307 7M545 545 11M775 775 3M200 200 5M315 315 7M560 560 11M800 800 3M206 206 5M325 325 7M580 580 11M825 825 3M212 212 5M335 335 7M600 600 11M850 850 3M218 218 5M345 345 7M615 615 11M875 875 3M224 224 5M355 355 7M630 630 11M900 900 3M230 230 5M365 365 7M650 650 11M925 925 3M236 236 5M375 375 7M670 670 11M950 950 3M243 243 5M387 387 7M690 690 11M975 975 3M250 250 5M400 400 7M710 710 11M1000 1000 3M258 258 5M412 412 7M730 730 11M1030 1030 3M265 265 5M425 425 7M750 750 11M1060 1060 3M272 272 5M437 437 7M775 775 11M1090 1090 3M280 280 5M450 450 7M800 800 11M1120 1120 3M290 290 5M462 462 7M825 825 11M1150 1150 3M300 300 5M475 475 7M850 850 11M1180 1180 3M307 307 5M487 487 7M875 875 11M1220 1220 3M315 315 5M500 500 7M900 900 11M1250 1250 3M325 325 5M515 515 7M925 925 11M1280 1280 3M335 335 5M530 530 7M950 950 11M1320 1320 3M345 345 5M545 545 7M975 975 11M1360 1360 3M355 355 5M560 560 7M1000 1000 11M1400 1400 3M365 365 5M580 580 7M1030 1030 11M1450 1450 3M375 375 5M600 600 7M1060 1060 11M1500 1500 3M387 387 5M615 615 7M1090 1090 11M1550 1550 3M400 400 5M630 630 7M1120 1120 11M1600 1600 3M412 412 5M650 650 7M1150 1150 11M1650 1650 3M425 425 5M670 670 7M1180 1180 11M1700 1700 3M437 437 5M690 690 7M1220 1220 11M1750 1750 3M450 450 5M710 710 7M1250 1250 11M1800 1800 3M462 462 5M730 730 7M1280 1280 11M1850 1850 3M475 475 5M750 750 7M1320 1320 11M1900 1900 3M487 487 5M775 775 7M1360 1360 11M1950 1950 3M500 500 5M800 800 7M1400 1400 11M2000 2000 3M515 515 5M825 825 7M1450 1450 11M2060 2060 3M530 530 5M850 850 7M1500 1500 11M2120 2120 3M545 545 5M875 875 7M1550 1550 11M2180 2180 3M560 560 5M900 900 7M1600 1600 3M580 580 5M925 925 7M1650 1650 11M2240 11M2300 2240 2300 3M600 600 5M950 950 7M1700 1700 3M615 615 5M975 975 7M1750 1750 3M630 630 5M1000 1000 7M1800 1800 3M650 650 5M1030 1030 7M1850 1850 3M670 670 5M1060 1060 7M1900 1900 3M690 690 5M1090 1090 7M1950 1950 3M710 710 5M1120 1120 7M2000 2000 3M730 3M750 730 750 5M1150 1150 7M2060 2060 5M1180 1180 7M2120 2120 5M1220 1220 7M2180 2180 5M1250 1250 5M1280 1280 7M2240 7M2300 2240 2300 5M1320 1320 5M1360 1360 5M1400 1400 Polyflex® ordering code is composed as follows: 5M1450 1450 5M1500 1500 3M600 5M1600 1600 5M1650 5M1850 1650 1850 3M - Rib width (3 mm) 600 - Effective length (mm) 23 V- Belts and V- Belt Pulleys Chapter 11 V- belts for Compact Drives Polyurethane multiple V- belt Polyflex® JB™ Polyflex® JB™ is synonymous with high power density in small spaces. Developed by Gates and produced to patented manufacturing processes, Gates Polyflex® JB™ belts provide more load- carrying capacity at higher speeds to small precision multiple V- belt drives. This results in significant cost savings and improved design freedom. Polyflex® JB™ belts are recommended for use on bench type milling machines, lathe drives, woodworking and metalworking machine spindle drives, computer peripheral equipment, small blowers, etc. Identification Durable marking indicating type and dimension. Construction Joined belt construction improves stability. Ribs relieve bending stress on small pulleys and provide lateral rigidity. 60° angle provides more undercord support to the tensile section and distributes the load more evenly. Small cross- section meets special application needs such as high shaft speeds, small drive package size and smooth running requirements. High modulus polyurethane compound with a high friction coefficient. The precise casting method eliminates overlaps and layers. Excellent adhesion of tensile cords and polyurethane compound leads to high fatigue resistance and long belt life. Extra toughness. The polyurethane compound resists fatigue, wear and ozone. Advantages Long belt life on small pulleys and compact drives. Greater shaft speeds, up to 30,000 rpm. High performance and smooth running for precision applications. Cost savings and design freedom. Avoids vibrations when subjected to shock loads. Temperature ranges from -54°C up to +85°C. NOTE Other number of ribs available on request. For detailed info, please contact your Gates representative. Sections and nominal dimensions Pitch mm 3M- JB 5M- JB 7M- JB 11M- JB 3,35 5,30 8,50 13,20 Width mm 3 5 7 11 Height mm 2,28 3,30 5,33 7,06 Standrad number of ribs 2 3 4 5 3M- JB x x 5M- JB x x x x 7M- JB 11M- JB x x x x x x Recommended minimum pulley diameter Profile 3M- JB 5M- JB 7M- JB 11M- JB Pulley diameter,mm 17 26 42 67 24 V- Belts and V- Belt Pulleys 3M- JB Description Effective lenght Chapter 11 5M- JB Description mm Effective lenght 7M- JB Description mm Effective lenght 11M- JB Description mm Effective lenght mm 3M175JB 175 5M280JB 280 7M500JB 490 11M710JB 692 3M180JB 180 5M290JB 290 7M515JB 505 11M730JB 712 3M185JB 185 5M300JB 300 7M530JB 520 11M750JB 732 3M190JB 190 5M307JB 307 7M545JB 535 11M775JB 757 3M195JB 195 5M315JB 315 7M560JB 550 11M800JB 782 3M200JB 200 5M325JB 325 7M580JB 570 11M825JB 807 3M206JB 206 5M335JB 335 7M600JB 590 11M850JB 832 3M212JB 212 5M345JB 345 7M615JB 605 11M875JB 857 3M218JB 218 5M355JB 355 7M630JB 620 11M900JB 882 3M224JB 224 5M365JB 365 7M650JB 640 11M925JB 907 3M230JB 230 5M375JB 375 7M670JB 660 11M950JB 932 3M236JB 236 5M387JB 387 7M690JB 680 11M975JB 957 3M243JB 243 5M400JB 400 7M710JB 703 11M1000JB 982 3M250JB 250 5M412JB 412 7M730JB 723 11M1030JB 1012 3M258JB 258 5M425JB 425 7M750JB 743 11M1060JB 1042 3M265JB 265 5M437JB 437 7M775JB 768 11M1090JB 1072 3M272JB 272 5M450JB 450 7M800JB 793 11M1120JB 1102 3M280JB 280 5M462JB 462 7M825JB 818 11M1150JB 1132 3M290JB 290 5M475JB 475 7M850JB 843 11M1180JB 1162 3M300JB 300 5M487JB 487 7M875JB 868 11M1220JB 1202 3M307JB 307 5M500JB 500 7M900JB 893 11M1250JB 1232 3M315JB 315 5M515JB 515 7M925JB 918 11M1280JB 1262 3M319JB 319 5M530JB 530 7M950JB 943 11M1320JB 1302 3M325JB 325 5M545JB 545 7M975JB 968 11M1360JB 1342 3M335JB 335 5M560JB 560 7M1000JB 993 11M1400JB 1382 3M345JB 345 5M580JB 580 7M1030JB 1023 11M1450JB 1432 3M350JB 350 5M600JB 600 7M1060JB 1053 11M1500JB 1482 3M355JB 355 5M615JB 615 7M1090JB 1083 11M1550JB 1532 3M365JB 365 5M630JB 630 7M1120JB 1113 11M1600JB 1582 3M375JB 375 5M650JB 650 7M1150JB 1143 11M1650JB 1632 3M387JB 387 5M670JB 670 7M1180JB 1173 11M1700JB 1682 3M400JB 400 5M690JB 690 7M1220JB 1213 11M1750JB 1732 3M406JB 406 5M710JB 710 7M1250JB 1243 11M1800JB 1782 3M412JB 412 5M730JB 730 7M1280JB 1273 11M1850JB 1832 3M425JB 425 5M750JB 750 7M1320JB 1313 11M1900JB 1882 3M437JB 437 5M775JB 775 7M1360JB 1353 11M1950JB 1932 3M450JB 450 5M800JB 800 7M1400JB 1393 11M2000JB 1982 3M462JB 462 5M825JB 825 7M1450JB 1443 11M2060JB 2042 3M475JB 475 5M850JB 850 7M1500JB 1493 11M2120JB 2102 3M487JB 487 5M875JB 875 7M1550JB 1543 11M2180JB 2162 3M500JB 500 5M900JB 900 7M1600JB 1593 3M515JB 515 5M925JB 925 7M1650JB 1643 11M2240JB 11M2300JB 2222 2282 3M530JB 530 5M950JB 950 7M1700JB 1693 3M545JB 545 5M975JB 975 7M1750JB 1743 3M553JB 553 5M1000JB 1000 7M1800JB 1793 3M560JB 560 5M1030JB 1030 7M1850JB 1843 3M580JB 580 5M1060JB 1060 7M1900JB 1893 3M600JB 600 5M1090JB 1090 7M1950JB 1943 3M615JB 615 5M1120JB 1120 7M2000JB 1993 3M630JB 630 5M1150JB 1150 7M2060JB 2053 3M650JB 650 5M1180JB 1180 7M2120JB 2113 3M670JB 670 5M1220JB 1220 7M2180JB 2173 3M690JB 690 5M1250JB 1250 3M710JB 710 5M1280JB 1280 7M2240JB 7M2300JB 2233 2293 3M730JB 3M750JB 730 750 5M1320JB 1320 5M1360JB 1360 5M1400JB 1400 5M1450JB 5M1500JB 1450 1500 Polyflex® JB™ ordering code is composed as follows: 5M280/3 5M - Rib width (5 mm) 280 - Effective length (mm) 3 - Number of ribs (joined belt) 25 V- Belts and V- Belt Pulleys Chapter 11 Heavy- duty V- Belts Multi- ribbed V- belt Micro- V® Micro- V® multi- ribbed belts ensure outstanding performance on any industrial multi- ribbed drive. They are suitable for industrial drives in washing machines, textile machines, vacuum cleaners, lawn mowers, machine tools, medical equipment and many more. The full line of MicroV® belt products includes slabs in several widths as well as single belts in PJ, PK, PL and PM sections in order to perfectly match customer requirements. Both slabs and belts can be manufactured in a great variety of number of ribs. Identification Durable yellow marking indicating type and dimension. Construction Truncated ribs ensure flexibility, reduce heat build- up and improve rib crack resistance. They also enhance load- carrying capacity on small diameter pulleys. High modulus, low stretch polyester tensile member provides superior resistance to fatigue and shock loads. All elastomeric rubber compound provides oil and heat resistance. Specially formulated fibre reinforced undercord stock improves belt stability. Advantages Extremely smooth and cool running. Very high power capacity per rib. Long life due to extra load- carrying capacity. Improved performance on back idlers. Smaller drive package Tolerant of pulley groove debris. Static conductive (ISO 1813) and can as such be used in the conditions described in the Directive 94/9/ EC ATEX. Sections and nominal dimensions Micro- V® belts are available in PJ, PK, PL and PM cross- sections. The figure below shows a cross- sectional view illustrating the nominal belt dimensions —rib width and belt height. All these belts will operate in standard pulleys provided the pulleys are manufactured to the DIN 7867 or ISO 9982 standard for the specific cross- section. Pitch mm Height mm PJ 2,34 3,6 PK 3,56 4,45 PL 4,70 6,4 PM 9,40 12,5 Nominal top width: b b = Nr x Sg Where: Nr = number of ribs S g = pulley groove spacing Recommended minimum pulley diameter Profile Pulley diameter,mm PJ 20 PK 50 PL 75 PM 180 26 V- Belts and V- Belt Pulleys PJ Chapter 11 PL Description Effective lenght DIN 7867 PJ406 PJ432 PJ457 PJ483 PJ508 PJ559 PJ584 PJ610 PJ660 PJ711 PJ723 PJ737 PJ762 PJ813 PJ838 PJ864 PJ914 PJ955 PJ965 PJ1016 PJ1041 PJ1067 PJ1092 PJ1105 PJ1110 PJ1118 PJ1123 PJ1130 PJ1136 PJ1150 PJ1168 PJ1194 PJ1200 PJ1222 PJ1233 PJ1244 PJ1262 PJ1270 PJ1280 PJ1300 PJ1309 PJ1321 PJ1333 PJ1355 PJ1371 PJ1397 PJ1428 PJ1439 PJ1473 PJ1549 PJ1600 PJ1651 PJ1663 PJ1752 PJ1854 PJ1895 PJ1910 PJ1930 PJ1956 PJ1981 PJ1992 PJ2083 PJ2210 PJ2337 PJ2489 mm 406 432 457 483 508 559 584 610 660 711 723 737 762 813 838 864 914 955 965 1016 1041 1067 1092 1105 1110 1118 1123 1130 1136 1150 1168 1194 1200 1222 1233 1244 1262 1270 1280 1300 1309 1321 1333 1355 1371 1397 1428 1439 1473 1549 1600 1651 1663 1752 1854 1895 1910 1930 1956 1981 1992 2083 2210 2337 2489 RMA 160 J 170 J 180 J 190 J 200 J 220 J 230 J 240 J 260 J 280 J 285 J 290 J 300 J 320 J 330 J 340 J 360 J 376 J 380 J 400 J 410 J 420 J 430 J 435 J 437 J 440 J 442 J 445 J 447 J 453 J 460 J 470 J 473 J 480 J 485 J 490 J 497 J 500 J 504 J 512 J 515 J 520 J 525 J 534 J 540 J 550 J 562 J 567 J 580 J 610 J 630 J 650 J 655 J 690 J 730 J 746 J 752 J 760 J 770 J 780 J 784 J 820 J 870 J 920 J 980 J Micro- V® ordering code is composed as follows: PM2286/28 PM - Section 2286 - Effective lenght (mm) 28 - Slabwidth (mm) PK Description Effective lenght DIN 7867 PL954 PL991 PL1075 PL1270 PL1333 PL1371 PL1397 PL1422 PL1562 PL1613 PL1664 PL1715 PL1765 PL1803 PL1842 PL1943 PL1981 PL2019 PL2070 PL2096 PL2134 PL2197 PL2235 PL2324 PL2362 PL2476 PL2515 PL2705 PL2743 PL2845 PL2896 PL2921 PL2997 PL3086 PL3125 PL3289 PL3327 PL3493 PL3696 mm 954 991 1075 1270 1333 1371 1397 1422 1562 1613 1664 1715 1765 1803 1842 1943 1981 2019 2070 2096 2134 2197 2235 2324 2362 2476 2515 2705 2743 2845 2895 2921 2997 3086 3125 3289 3327 3493 3696 RMA 375 L 390 L 423 L 500 L 525 L 540 L 550 L 560 L 615 L 635 L 655 L 675 L 695 L 710 L 725 L 765 L 780 L 795 L 815 L 825 L 840 L 865 L 880 L 915 L 930 L 975 L 990 L 1065 L 1080 L 1120 L 1140 L 1150 L 1180 L 1215 L 1230 L 1295 L 1310 L 1375 L 1455 L PM Description DIN 7867 PM2286 PM2388 PM2515 PM2693 PM2832 PM2921 PM3010 PM3124 PM3327 PM3531 PM3734 PM4089 PM4191 PM4470 PM4648 PM5029 PM5410 PM6121 PM6502 PM6883 PM7646 PM8408 PM9169 PM9931 Effective lenght RMA 900 M 940 M 990 M 1060 M 1115 M 1150 M 1185 M 1230 M 1310 M 1390 M 1470 M 1610 M 1650 M 1760 M 1830 M 1980 M 2130 M 2410 M 2560 M 2710 M 3010 M 3310 M 3610 M 3910 M mm 2286 2388 2515 2693 2832 2921 3010 3124 3327 3531 3734 4089 4191 4470 4648 5029 5410 6121 6502 6883 7646 8408 9169 9931 Description Effective lenght Slab width DIN 8769 PK630 PK650 PK675 PK698 PK700 PK730 PK755 PK775 PK800 PK830 PK845 PK870 PK875 PK885 PK890 PK920 PK925 PK950 PK954 PK970 PK1000 PK1015 PK1035 PK1060 PK1080 PK1090 PK1125 PK1145 PK1150 PK1165 PK1190 PK1200 PK1222 PK1230 PK1245 PK1270 PK1300 PK1330 PK1335 PK1345 PK1385 PK1420 PK1460 PK1490 PK1520 PK1555 PK1560 PK1570 PK1610 PK1655 PK1690 PK1700 PK1725 PK1755 PK1800 PK1860 PK1885 PK1890 PK1900 PK1980 PK2050 PK2080 PK2120 PK2145 PK2235 PK2280 PK2330 PK2490 mm 630 650 675 698 700 730 755 775 800 830 845 870 875 885 890 920 925 950 954 970 1000 1015 1035 1060 1080 1090 1125 1145 1150 1165 1190 1200 1222 1230 1245 1270 1300 1330 1335 1345 1385 1420 1460 1490 1520 1555 1560 1570 1610 1655 1690 1700 1725 1755 1800 1860 1885 1890 1900 1980 2050 2080 2120 2145 2235 2280 2330 2490 (ribs) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 308 (4x77) 264 (4x66) 264 (4x66) 264 (4x66) 264 (4x66) 264 (4x66) 264 (4x66) 264 (4x66) 264 (4x66) 264 (4x66) 264 (4x66) 264 (4x66) 264 (4x66) 264 (4x66) 264 (4x66) 27 V- Belts and V- Belt Pulleys Chapter 11 Joint Belt Round belts Greenthane- polyurethane Ø mm Minimum pulley DM m/ roll mm Weight per roll Items kg 3 30 100 1,75 102662 4 40 100 2,55 102661 5 50 100 3,23 102660 6 60 50 2,5 102659 8 80 50 3,9 102655 10 100 50 5,75 102652 12 120 25 4,75 102648 15 150 25 6,4 102645 18 180 25 8,9 102639 20 200 25 10,75 102638 Round belt of high quality polyurethan for transporting and power transmission Advantage: High raw material quality Elastic No need of special pulley Low maintenance Resistant against chemicals and oils Low wear Area of application: Food Industry Printing machines Package machines Concrete industry Roof covering industry Agriculture Metal industry Wood industry Textile machines Glass industry Medical industry Belt strngth :55 N/ mm2. Share (shore): 87°A ± 2°. Working temperature °C: -20 til +80. Minimum breaking level: 580%. 28 V- Belts and V- Belt Pulleys Chapter 11 Other types that can be supplied: Redthane Solid round 3, 4 ,5 ,6, 8, 10, 12,15, 18 og 20 mm. Tubular Round 5, 6, 8, 10 og 12,5 mm. Belt Z- A- B- C. Transthane Solid round 5, 6, 8, 10, 12, 15 og 18 mm. V- belt Z- A- B- C. Jointing Hollow belts DIN 2216 Profile Z10 A13 B17 C22 Link belt Nu- T- Link Super T- Link Belt profile Belt width mm Z 10 A 13 B 17 C 22 SPA 13 SPB 17 29 V- Belts and V- Belt Pulleys Chapter 11 V- Belt Pulleys for Taper Bushers The pulleys conform to ISO 4183 and DIN 2211. Designed for use with both wedge(narrow) and classical V- belts B=E(n-1)+2F n=No. og grooves Dimensions in milimetres A1 Material: Fine grain cast- iron grade 220-260 Eccentricity of O/ D to bore DIN 2211 part 1 Groove side wobble tolerance: DIN 2211 part 1 Surface roughness: ISO 254 Balance quality grade: ISO 1940 Dynamic balancing can besupplied to order. Pulleys with dm (pcd) >125 mm are statically balanced to grade G 6,3. A residual unbalance of 2 g on the pulley dm (pcd) will be accepted. The residual unbalance is ≤100 g mm/ kg at 600 rev./ min. and 20 g mm/ kg at 3000 rev./ min. Dynamic balancing can be supplied to order. Profil Dm α br E F C t SPZ ≤80 >80 34 38 8,5 12,0 8,0 2,0 11,0 SPA ≤118 >118 34 38 11,0 15,0 10,0 2,8 13,8 SPB ≤190 >190 34 38 14,0 19,0 12,5 3,5 17,5 SPC ≤315 >315 34 38 19,0 25,5 17,0 4,8 23,8 30 V- Belts and V- Belt Pulleys Chapter 11 SPZ Ordering code is composed as follow: SPZ 125-3/2010 SPZ Section 125 Pulley diameter 3 Number of grooves 2012 Bush size DM Groove 50 1 2 1 2 1 2 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 4 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 6 56 60 63 67 71 75 80 85 90 95 100 Bush no 1008 1008 1008 1108 1008 1108 1108 1108 1108 1108 1108 1108 1108 1108 1108 1108 1210 1210 1210 1210 1210 1210 1210 1610 1610 1610 1610 1210 1610 1610 1610 1610 1210 1610 1610 1610 1610 1210 1610 1610 1610 2012 2012 Max Bore 25 25 25 28 25 28 28 28 28 28 28 28 28 28 28 28 32 32 32 32 32 32 32 42 42 42 42 32 42 42 42 42 32 42 42 42 42 32 42 42 42 50 50 Fig B J K L M N Weight DM Groove 9 9 9 9 1 9 1 3 3 1 3 3 1 3 3 1 3 3 1 3 3 3 1 3 3 3 3 1 3 3 3 3 1 3 3 3 3 1 3 3 3 3 3 16 28 16 28 16 28 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 52 16 28 40 52 64 16 28 40 52 64 16 28 40 52 64 16 28 40 52 64 76 26 26 30 30 34 37 37 38 38 42 42 46 46 51 51 51 56 56 56 56 61 61 61 61 66 66 66 66 71 71 71 71 71 15 27 15 27 27 6 18 6 18 6 18 3 15 3 15 27 3 15 27 39 3 15 27 39 3 15 27 39 3 15 27 32 44 37 49 37 49 22 49 22 22 22 22 22 22 22 22 22 22 25 25 26,5 25 25 25 25 25 25 25 25 26,5 25 25 25 25 26,5 25 25 25 25 25 25 25 25 32 32 6 6 6 6 6 10,5 9 10,5 10,5 9 - 60 60 60 60 55 64 60 60 60 60 75 83 83 83 83 - 0,3 0,4 0,4 0,5 0,2 0,6 0,2 0,3 0,4 0,3 0,4 0,5 0,3 0,4 0,6 0,4 0,4 0,5 0,5 0,6 0,7 0,8 0,6 0,5 0,6 0,9 1 0,7 0,7 0,8 1 1,2 0,7 0,8 0,9 1,1 1,3 0,8 0,9 1,1 1,1 1,3 1,4 106 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 8 1 2 3 4 5 6 8 112 118 125 132 140 150 Bush no 1610 1610 1610 1610 2012 2012 1610 1610 2012 2012 2012 2012 1610 1610 2012 2012 2012 2517 1610 1610 2012 2012 2012 2517 1610 1610 2012 2012 2517 2517 1610 1610 2012 2012 2517 2517 2517 1610 2012 2012 2517 2517 2517 2517 Max Fig B J K Bore 42 1 16 42 3 28 42 3 40 77 15 42 3 52 77 27 50 3 64 77 32 50 3 76 77 44 42 1 16 42 3 28 83 3 50 3 40 83 8 50 3 52 83 20 50 3 64 83 32 50 3 76 83 44 42 1 16 42 3 28 89 3 50 3 40 89 8 50 3 52 89 20 50 3 64 89 32 65 3 76 89 31 42 1 16 42 3 28 96 3 50 2 40 96 50 2 52 96 50 3 64 96 32 65 3 76 96 31 42 1 16 42 3 28 111 3 50 2 40 111 50 2 52 111 65 3 64 111 19 65 3 76 111 31 42 1 16 42 2 28 111 50 2 40 111 50 2 52 111 65 2 64 111 65 2 76 111 65 4 100 111 27,5 42 1 16 50 1 28 50 2 40 121 65 2 52 121 65 2 64 121 65 2 76 121 65 4 100 121 27,5 L 25 28 25 25 32 32 25 25 32 32 32 32 25 25 32 32 32 45 25 25 32 32 32 45 25 25 32 32 45 45 25 25 32 32 45 45 45 25 33,5 32 45 45 45 45 M N 9 83 9 92 9 92 9 92 8 20 9 92 8 20 9 92 3 8 20 19 31 27,5 9 92 5,5 112 8 7 19 31 27,5 - Weight 0,9 1,1 1,3 1,3 1,5 1,6 1 1,3 1,3 1,5 1,8 1,9 0,9 1,3 1,6 1,8 1,8 2 1 1,4 1,8 2,2 2,3 2,5 1,1 1,5 2,3 2,5 2,7 2,9 1,2 1,7 2,6 2,9 3,2 3,5 4 1,2 2 3,1 3,7 4 4,4 5,1 31 V- Belts and V- Belt Pulleys Chapter 11 SPZ DM Groove 160 1 2 3 4 5 6 8 1 2 3 4 5 6 8 1 2 3 4 5 6 8 1 2 3 4 5 6 8 1 2 3 4 5 6 8 1 2 3 4 5 6 8 170 180 190 200 224 Bush no 1610 2012 2012 2517 2517 2517 2517 1610 2012 2012 2517 2517 2517 2517 1610 2012 2012 2517 2517 2517 3020 1610 2012 2012 2517 2517 2517 3020 2012 2012 2012 2517 2517 2517 3020 2012 2012 2012 2517 2517 2517 3020 Max Bore 42 50 50 65 65 65 65 42 50 50 65 65 65 65 42 50 50 65 65 65 75 42 50 50 65 65 65 75 50 50 50 65 65 65 75 50 50 50 65 65 65 75 Fig B J K L M N Weight DM Groove 1 1 2 2 2 2 4 1 1 6 2 2 2 4 1 1 6 6 6 6 4 1 1 6 6 6 6 4 7 7 6 6 6 6 4 5 5 6 8 6 6 4 16 28 40 52 64 76 100 16 28 40 52 64 76 100 16 28 40 52 64 76 100 16 28 40 52 64 76 100 16 28 40 52 64 76 100 16 28 40 52 64 76 100 131 131 131 131 131 141 141 141 141 141 151 151 151 151 151 161 161 161 161 161 171 171 171 171 171 195 195 195 195 195 195 195 27,5 27,5 24,5 24,5 3,5 9,5 15,5 24,5 8 2 4 3,5 9,5 15,5 24,5 25 32 32 45 45 45 45 25 32 32 45 45 45 45 25 32 32 45 45 45 51 25 32 32 45 45 45 51 32 32 32 45 45 45 51 32 32 32 45 45 45 51 9 4 8 7 19 31 27,5 9 4 8 7 19 31 27,5 9 4 8 7 19 31 24,5 9 4 8 7 19 31 24,5 16 4 8 3,5 9,5 15,5 24,5 8 2 4 3,5 9,5 15,5 24,5 92 112 92 112 112 92 112 112 124 124 124 92 112 112 124 124 124 112 112 112 124 124 124 112 112 112 124 124 124 - 1,3 2,5 3,6 4,4 4,8 5,2 5,6 1,5 2,5 4,2 5,3 5,9 6,5 6,8 1,6 2,5 4,8 6,1 6,3 6,8 7,1 1,8 2,6 4,9 5,3 6,3 6,9 8,2 2,3 2,8 3,5 4,7 5,5 6,1 9,3 2,5 3,2 3,9 5,2 6 6,6 11,8 250 1 2 3 4 5 6 8 1 2 3 4 5 6 8 1 2 3 4 5 6 8 1 2 3 4 5 6 8 1 2 3 4 5 6 8 1 2 3 4 5 6 8 280 315 355 400 450 Bush no 2012 2012 2012 2517 2517 2517 3020 2012 2012 2517 2517 2517 2517 3020 2012 2012 2517 2517 2517 2517 3020 2012 2012 2517 2517 2517 2517 3020 2012 2517 2517 2517 3020 3020 3030 2517 2517 2517 3020 3020 3030 3535 Max Bore 50 50 50 65 65 65 75 50 50 65 65 65 65 75 50 50 65 65 65 65 75 50 50 65 65 65 65 75 50 65 65 65 75 75 75 65 65 65 75 75 75 90 Fig B J K L M N Weight 7 7 8 8 8 8 8 7 7 7 8 8 8 8 7 7 7 8 8 8 8 7 7 7 8 8 8 8 7 7 7 8 8 8 8 7 7 7 8 8 8 8 16 28 40 52 64 76 100 16 28 40 52 64 76 100 16 28 40 52 64 76 100 16 28 40 52 64 76 100 16 28 40 52 64 76 100 16 28 40 52 64 76 100 221 221 221 221 221 221 221 251 251 251 251 251 251 251 286 286 286 286 286 286 286 326 326 326 326 326 326 326 371 371 371 371 371 371 371 424 424 424 424 424 424 424 8 2 4 3,5 9,5 15,5 24,5 8 2 2,5 3,5 9,5 15,5 24,5 8 2 2,5 3,5 9,5 15,5 24,5 8 2 2,5 3,5 9,5 15,5 12 8 8,5 2,5 3,5 6,5 12,5 12 14,5 8,5 2,5 0,5 6,5 5,5 32 32 32 45 45 45 51 32 32 45 45 45 45 51 32 32 45 45 45 45 51 32 32 45 45 45 45 76 32 45 45 45 51 51 76 45 45 45 51 51 76 89 8 2 4 3,5 9,5 15,5 24,5 8 2 2,5 3,5 9,5 15,5 24,5 8 2 2,5 3,5 9,5 15,5 24,5 8 2 2,5 3,5 9,5 15,5 12 8 8,5 2,5 3,5 6,5 12,5 12 14,5 8,5 2,5 0,5 6,5 5,5 112 112 112 124 124 124 145 112 112 124 124 124 124 145 112 112 124 124 124 124 145 112 112 124 124 124 124 145 112 124 124 124 145 145 145 120 120 120 145 145 145 178 2,8 3,5 4,3 5,7 6,4 7 10,5 2,9 4 5,3 6,4 7,1 7,8 10,8 3,1 4,2 6,1 7,6 8,6 9,3 12,9 3,5 5,1 7,3 8,9 10 10,7 16 6 6,3 8 10,1 11,7 14,5 18,2 6,1 8,2 9,8 11,8 13,9 16,9 24 32 V- Belts and V- Belt Pulleys Chapter 11 SPZ DM Groove Bush no Max Bore Fig B J K L M N Weight 500 1 2517 65 7 16 471 14,5 45 14,5 124 6,7 2 2517 65 7 28 471 8,5 45 8,5 124 9,1 3 2517 65 7 40 471 2,5 45 2,5 124 11,4 4 3020 75 8 52 471 0,5 51 0,5 159 14,3 5 3020 75 8 64 471 6,5 51 6,5 145 17,6 6 3020 75 8 76 471 12,5 51 12,5 145 19,9 8 3535 90 8 100 471 5,5 89 5,5 178 26 2 2517 65 7 28 601 8,5 45 8,5 124 11,7 3 2517 65 7 40 601 2,5 45 2,5 124 15,9 4 3020 75 8 52 601 0,5 51 0,5 145 20 5 3020 75 8 64 601 6,5 51 6,5 145 22,7 6 3525 90 8 76 601 5,5 65 5,5 178 30,9 6 3535 90 7 76 601 6,5 89 6,5 178 33,6 8 3535 90 8 100 601 5,5 89 5,5 178 35,8 630 33 V- Belts and V- Belt Pulleys Chapter 11 SPA Ordering code is composed as follow: SPA 100-2/1610 SPA Section 100 Pulley diameter 2 Number of grooves 1610 Bush size DM Groove 63 1 2 1 2 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 4 1 2 3 4 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 67 71 75 80 85 90 95 100 106 112 Bush no 1108 1108 1108 1108 1108 1108 1108 1108 1108 1108 1210 1210 1210 1210 1210 1210 1210 1610 1610 1610 1210 1610 1610 1610 1610 1610 1610 1610 1610 1610 1610 1610 1610 2012 2012 2012 1610 1610 2012 2012 2012 2012 Max Bore 28 28 28 28 28 28 28 28 28 28 32 32 32 32 32 32 32 42 42 42 32 42 42 42 42 42 42 42 42 42 42 42 42 50 50 50 42 42 50 50 50 50 Fig B 9 9 1 3 1 3 3 1 3 3 1 3 3 1 3 3 1 3 3 3 1 3 3 3 1 3 2 2 3 4 1 3 2 3 3 3 1 3 3 3 3 3 20 35 20 35 20 35 50 20 35 50 20 35 50 20 35 50 20 35 50 65 20 35 50 65 20 35 50 65 80 95 20 35 50 65 80 95 20 35 50 65 80 95 J K 31 18 31 33 35 13 39 13 39 28 43 13 43 28 50 10 50 25 55 10 55 25 60 10 60 23,5 60 40 65 10 65 23,5 65 40 65 10 65 65 65 55 65 30 70 10 70 70 33 70 48 70 63 77 10 77 18 77 33 77 48 77 63 L 40 55 22 22 22 22 22 22 22 22 25 25 25 25 25 25 25 25 26,5 25 25 25 26,5 25 25 25 25 25 25 25 25 25 25 32 32 32 25 25 32 32 32 32 M N - 68,5 - 68,5 2 60 2 60 2 60 5 80 5 80 5 80 5 80 5 92 25 40 40 5 92 25 5 92 - Weight DM Groove 0,6 0,8 0,3 0,5 0,3 0,5 0,7 0,4 0,6 0,8 0,5 0,6 0,9 0,6 0,7 1 0,7 0,7 1 1,2 0,8 0,9 1,1 1,4 0,8 0,9 1,2 1,7 1,9 2,3 0,9 1,1 1,4 2 2 2,4 1 1,2 1,3 1,9 2,1 2,4 118 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 125 132 140 150 160 170 Bush no 1610 1610 2012 2012 2012 2012 1610 1610 2012 2012 2012 2012 1610 2012 2012 2517 2517 2517 1610 2012 2517 2517 2517 2517 1610 2012 2517 2517 2517 2517 1610 2012 2517 2517 2517 2517 1610 2012 2517 2517 3020 3020 Max Bore 42 42 50 50 50 50 42 42 50 50 50 50 42 50 50 65 65 65 42 50 65 65 65 65 42 50 65 65 65 65 42 50 65 65 65 65 42 50 65 65 75 75 Fig B J K L M N Weight 1 3 2 2 2 3 1 2 2 2 2 4 1 2 2 2 2 4 1 2 2 2 2 4 1 2 2 2 2 4 5 2 2 2 2 4 5 2 2 2 2 4 20 35 50 65 80 95 20 35 50 65 80 95 20 35 50 65 80 95 20 35 50 65 80 95 20 35 50 65 80 95 20 35 50 65 80 95 20 35 50 65 80 95 84 84 84 84 84 90 90 90 90 90 98 98 98 98 98 105 105 105 105 105 115 115 115 115 115 125 125 125 125 125 125 135 135 135 135 135 135 10 63 31,5 25 25 25 25 22 25 25 32 32 32 32 25 25 32 32 32 32 26,5 32 32 45 45 45 25 32 45 45 45 45 25 32 45 45 45 45 25 32 45 45 45 45 25 32 45 45 51 51 5 18 33 48 5 10 18 33 48 31,5 6,5 3 18 20 35 25 5 3 5 20 35 25 5 3 5 20 35 25 5 3 5 20 35 25 5 3 5 20 29 22 85 92 92 92 92 92 92 - 1,2 1,4 1,8 2 2,4 2,7 1,4 1,7 2 2,5 2,7 3 1,6 1,8 2,3 2,6 2,9 3,3 1,8 2 2,8 3,1 3,4 3,8 1,4 2,4 3,5 3,8 4,2 4,8 1,9 2,9 3,9 4,4 5,1 5,8 2 3,1 4,6 5,5 5,9 6,5 34 V- Belts and V- Belt Pulleys Chapter 11 SPA DM Groove 180 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 190 200 212 224 236 250 Bush no 1610 2012 2517 2517 3020 3020 1610 2012 2517 2517 3020 3020 2012 2517 2517 3020 3020 3020 2012 2517 2517 3020 3020 3020 2012 2517 2517 3020 3020 3020 2012 2517 2517 3020 3020 3020 2012 2517 2517 3020 3020 3020 Max Fig B J Bore 42 5 20 145 50 6 35 145 65 2 50 145 65 2 65 145 75 2 80 145 75 4 95 145 42 7 20 155 55 6 35 155 65 2 50 155 65 2 65 155 75 2 80 155 75 4 95 155 50 7 20 165 65 5 35 165 65 6 50 165 75 2 65 165 75 4 80 165 75 4 95 165 50 5 20 177 65 5 35 177 65 8 50 177 75 2 65 177 75 2 80 177 75 4 95 177 50 7 20 189 65 7 35 189 65 8 50 189 75 2 65 189 75 2 80 189 75 4 95 189 50 7 20 201 65 5 35 201 65 8 50 201 75 2 65 201 75 2 80 201 75 4 95 201 50 7 20 215 65 7 35 215 65 8 50 215 75 6 65 215 75 6 80 215 75 6 95 215 K L M N Weight DM Groove 22 22 14,5 22 22 2,5 22 2,5 22 2,5 7 14,5 22 25 32 45 45 51 51 25 32 45 45 51 51 32 45 45 51 51 51 32 45 45 51 51 51 32 45 45 52,5 52,5 51 32 45 45 52,5 52,5 51 32 45 45 51 51 51 5 3 5 20 29 22 5 3 5 20 29 22 12 10 5 14 14,5 22 12 10 5 14 29 22 12 10 2,5 12,5 27,5 22 12 10 2,5 12,5 27,5 22 12 10 2,5 7 14,5 22 92 110 92 110 112 124 124 112 124 124 112 124 124 112 124 124 112 124 124 159 159 159 2,1 3,4 5,1 5,9 6,2 6,7 2,3 3,8 5,4 6,8 7,4 8,1 2,6 4,1 4,9 7,4 8,4 9,4 2,7 4,3 5,2 7,3 8,2 9,2 2,7 4,4 5,5 7,4 8,3 9,4 2,8 4,6 5,7 7,8 8,7 9,7 2,9 4,8 5,9 8 9 10 265 1 2 3 4 5 6 1 2 3 4 5 5 6 1 2 3 4 5 5 6 1 2 3 4 5 5 6 1 2 3 4 5 5 6 1 2 3 4 5 5 6 280 300 315 355 400 Bush no 2012 2517 2517 3020 3020 3020 2012 2517 2517 3020 3525 3535 3525 2012 2517 3020 3020 3525 3535 3525 2012 2517 3020 3020 3525 3535 3525 2012 2517 3020 3020 3525 3535 3525 2012 2517 3020 3020 3525 3535 3525 Max Bore 50 65 65 75 75 75 50 65 65 75 90 90 90 50 65 75 75 90 90 90 50 65 75 75 90 90 90 50 65 75 75 90 90 90 50 65 75 75 90 90 90 Fig B J K 7 7 8 6 6 6 7 7 6 6 6 5 6 7 7 5 6 6 5 6 7 7 5 6 6 5 6 7 7 7 8 8 7 8 7 7 7 8 8 7 8 20 35 50 65 80 95 20 35 50 65 80 80 95 20 35 50 65 80 80 95 20 35 50 65 80 80 95 20 35 50 65 80 80 95 20 35 50 65 80 80 95 230 230 230 230 230 230 248 248 248 248 248 248 248 265 265 265 265 265 265 265 280 280 280 280 280 280 280 320 320 320 320 320 320 320 365 365 365 365 365 365 365 2,5 7 14,5 22 2,5 7 7,5 4,5 15 0,5 7 7,5 4,5 15 0,5 7 7,5 4,5 15 0,5 7 7,5 4,5 15 0,5 7 7,5 4,5 15 L M 32 12 45 10 45 2,5 51 7 51 14,5 51 22 32 12 45 10 45 2,5 51 7 65 7,5 89 4,5 65 15 32 12 45 10 51 0,5 51 7 65 7,5 89 4,5 65 15 32 12 45 10 51 0,5 51 7 65 7,5 89 4,5 65 15 32 12 45 10 51 0,5 51 7 65 7,5 89 4,5 65 15 32 12 45 10 51 0,5 51 7 65 7,5 89 4,5 65 15 N Weight 112 124 159 159 159 159 112 124 159 159 178 178 178 112 124 159 159 178 178 178 112 124 159 159 178 178 178 112 124 159 159 178 178 178 112 124 159 159 178 178 178 3,1 5,1 6,3 8,4 9,5 10,5 3,3 5,4 6,7 8,8 12,8 15,5 14,5 3,5 5,8 7,4 9,3 13,5 16,2 15,5 3,6 6 8,3 9,7 14,3 17 17,5 4,2 6,7 9,2 11 15,9 18,6 19 4,9 8,1 11 12,8 18,3 21 22 35 V- Belts and V- Belt Pulleys Chapter 11 SPA DM Groove 450 1 2 3 4 5 5 6 1 2 3 4 5 5 6 1 2 3 4 4 5 5 6 1 2 3 4 4 5 5 6 2 2 3 3 4 4 5 5 6 3 3 4 4 5 5 6 500 560 630 800 900 Bush no 2012 2517 3020 3020 3525 3535 3525 2517 2517 3020 3020 3525 3535 3525 2517 3020 3020 3525 3535 3525 3535 3525 2517 3020 3020 3525 3535 3525 3535 4030 3525 3535 3525 3535 3525 3535 4030 4040 4030 3525 3535 3525 3535 4030 4040 4030 Max Bore 50 65 75 75 90 90 90 65 65 75 75 90 90 90 65 75 75 90 90 90 90 90 65 75 75 90 90 90 90 100 90 90 90 90 90 90 100 100 100 90 90 90 90 100 100 100 Fig B J K L M N Weight 7 7 7 8 8 7 8 7 7 7 8 8 7 8 7 7 7 7 7 8 7 8 7 7 7 7 7 8 7 8 7 7 7 7 7 7 8 7 8 7 7 7 7 8 7 8 20 35 50 65 80 80 95 20 35 50 65 80 80 95 20 35 50 65 65 80 80 95 20 35 50 65 65 80 80 95 35 35 50 50 65 65 80 80 95 50 50 65 65 80 80 95 418 418 418 418 418 418 418 465 465 465 465 465 465 465 525 525 525 525 525 525 525 525 595 595 595 595 595 595 595 595 766 766 766 766 766 766 766 766 766 866 866 866 866 866 866 866 0,5 7 7,5 4,5 15 0,5 7 7,5 4,5 15 0,5 12 7,5 4,5 15 0,5 12 7,5 4,5 9,5 15 27 7,5 19,5 12 2 11 9,5 7,5 19,5 12 2 11 9,5 32 45 51 51 65 89 65 45 45 51 51 65 89 65 45 51 51 65 89 65 89 65 45 51 51 65 89 65 89 76 65 89 65 89 65 89 76 102 76 65 89 65 89 76 102 96 12 10 0,5 7 7,5 4,5 15 25 10 0,5 7 7,5 4,5 15 25 16 0,5 12 7,5 4,5 15 25 16 0,5 12 7,5 4,5 9,5 15 27 7,5 19,5 12 2 11 9,5 7,5 19,5 12 2 11 9,5 112 124 159 159 178 178 178 124 124 159 159 178 178 178 124 159 159 178 178 178 178 178 124 159 159 178 178 178 178 216 178 178 178 178 178 178 216 216 216 178 178 178 178 216 216 216 7 10,3 14,1 15,5 21,6 24,3 25,2 8 11,6 16 18,2 24,6 27,3 28 11,6 15,5 17,8 24 26,7 27,7 30,4 31,5 10,1 16 22 28,1 30,8 31 33,7 42 26,6 29,3 31,8 34,5 36,3 39 49 54 55 36,6 39,3 42,8 45,5 53,7 58,7 60,5 36 V- Belts and V- Belt Pulleys Chapter 11 SPB Ordering code is composed as follow: SPB 200-4/3020 SPB Section 200 Pulley diameter 4 Number of grooves 3020 Bush size DM Groove 100 1 2 3 1 2 3 1 2 3 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 8 112 118 125 132 140 150 160 170 Bush no 1610 1610 1610 1610 1610 1610 1610 1610 1610 1610 2012 2012 2012 2012 1610 2012 2012 2012 2012 1610 2012 2012 2517 2517 2517 1610 2012 2517 2517 2517 2517 1610 2012 2517 2517 2517 3020 1610 2012 2517 2517 3020 3020 3020 Max Bore 42 42 42 42 42 42 42 42 42 42 50 50 50 50 42 50 50 50 50 42 50 50 65 65 65 42 50 65 65 65 65 42 50 65 65 65 75 42 50 65 65 75 75 75 Fig B J K L M N Weight DM Groove 1 3 3 1 3 3 1 3 3 1 2 2 4 3 1 2 2 4 4 1 2 2 2 2 4 1 2 2 2 4 4 1 2 2 4 4 4 1 2 2 4 4 4 4 25 44 63 25 44 63 25 44 63 25 44 63 82 101 25 44 63 82 101 25 44 63 82 101 120 25 44 63 82 101 120 25 44 63 82 101 120 25 44 63 82 101 120 158 62 62 75 75 81 81 85 85 85 85 92 92 92 92 100 100 100 100 100 110 110 110 110 110 114 114 114 114 114 124 124 124 124 124 129 19 38 19 38 19 38 25 69 25 34,5 37,5 28 37,5 18,5 28 34,5 18,5 25 34,5 53,5 25 25 25 25 25 25 25 25 25 25 32 32 32 32 25 32 32 32 32 25 32 32 45 45 45 25 32 45 45 45 45 25 32 45 45 45 51 25 32 45 45 51 51 51 12 31 25 12 31 25 34,5 12 31 37 56 37,5 12 18 37 28 37,5 12 18 18,5 28 34,5 12 18 18,5 25 34,5 53,5 92 92 92 92 92 92 92 - 0,9 1,2 1,7 1,1 1,5 2 1,3 1,7 2,3 1,5 1,9 2,4 3 3,5 1,8 2,2 2,8 3,4 3,7 2,3 2,7 3,3 3,7 4,5 4,6 2,7 3,1 3,9 4,4 5,2 5,6 2,5 2,9 4,2 4,9 6 5,4 2,9 3,3 4,9 5,7 6,1 6,5 8 180 1 2 3 4 5 6 8 1 2 3 4 5 6 8 1 2 3 4 5 6 8 8 1 2 3 4 5 6 6 8 8 1 2 3 4 5 6 6 8 8 10 10 190 200 212 224 Bush no 1610 2517 2517 2517 3020 3020 3020 2012 2517 2517 2517 3020 3020 3020 2012 2517 2517 3020 3020 3020 3525 3535 2012 2517 2517 3020 3020 3525 3535 3525 3535 2012 2517 2517 3020 3020 3525 3535 3525 3535 3525 3535 Max Fig B Bore 42 1 25 65 1 44 65 2 63 65 4 82 75 4 101 75 4 120 75 4 158 50 1 25 65 1 44 65 2 63 65 4 82 75 4 101 75 4 120 75 4 158 50 1 25 65 1 44 65 2 63 75 2 82 75 2 101 75 4 120 90 4 158 90 4 158 50 7 25 65 1 44 65 2 63 75 2 82 75 2 101 90 4 120 90 4 120 90 4 158 90 4 158 50 1 25 65 1 44 65 2 63 75 2 82 75 2 101 90 4 120 90 4 120 90 4 158 90 4 158 90 4 196 90 4 196 J K L M N Weight 134 134 134 134 134 139 144 144 144 144 149 154 154 154 154 159 159 166,5 166,5 166,5 166,5 166,5 171 171 178 178 178 178 178 184 184 184 184 18,5 25 34,5 53,5 18,5 25 34,5 53,5 34,5 46,5 34,5 27,5 15,5 46,5 34,5 27,5 15,5 46,5 34,5 65,5 46 25 45 45 45 51 51 51 32 45 45 45 51 51 51 32 45 45 51 51 51 65 89 32 45 45 51 51 65 89 65 89 32 45 45 51 51 65 89 65 89 65 89 1 18 18,5 25 34,5 53,5 7 1 18 18,5 25 34,5 53,5 7 1 18 31 50 34,5 46,5 34,5 7 1 18 31 50 27,5 15,5 46,5 34,5 7 1 18 31 50 27,5 15,5 46,5 34,5 65,5 61 92 112 124 95 124 95 124 95 124 - 4,1 4,5 5,5 6,9 7,1 7,7 9,5 4,6 5 6,3 7,6 8,1 9,2 11,2 5 5,4 6,5 8,8 9,1 10,3 11,5 13,5 4,2 4,9 6 9,8 11 12,5 14,3 15,5 16,6 4,7 5,3 6,3 11,3 12,7 15 17 18 19,3 20,5 21,8 37 V- Belts and V- Belt Pulleys Chapter 11 SPB 1 Bush no 2012 Max Bore 50 Fig B J K L M N Weight DM Groove 1 25 198 - 32 7 95 5 315 1 Bush no 2012 2 2517 65 1 44 198 - 45 1 124 5,5 2 2517 65 3 2517 65 8 63 198 - 45 18 - 7 3 3020 4 3020 75 8 82 198 - 14,5 4 5 3525 90 4 101 198 18 65 18 - 15,2 5 3535 90 3 101 198 - 89 12 - 16,9 6 3525 90 4 120 198 27,5 65 27,5 - 6 3535 90 4 120 198 15,5 89 15,5 8 3525 90 4 158 198 8 3535 90 4 10 3525 90 10 3535 90 1 2012 2 2517 3 DM Groove 236 250 265 280 300 Max Fig Bore 50 7 B J K L M N Weight 25 277 - 32 7 95 7,2 7 44 269 0,5 45 0,5 124 7,8 75 8 63 269 6 51 6 159 9,6 3525 90 6 82 269 8,5 65 8,5 178 14,4 4 3535 90 5 82 269 3,5 89 3,5 178 17,1 5 3525 90 6 101 269 18 65 18 178 16,1 18,5 5 3535 90 6 101 269 6 89 6 178 18,8 - 20 6 3525 90 6 120 269 27,5 65 27,5 178 20,3 46,5 65 46,5 - 21,5 6 3535 90 6 120 269 15,5 89 15,5 178 23 158 198 34,5 89 34,5 - 22,3 8 3525 90 6 158 274 46,5 65 46,5 178 23,3 4 196 198 65,5 65 65,5 - 22,6 8 3535 90 6 158 274 34,5 89 34,5 178 26 4 196 198 53,5 89 53,5 - 25,3 10 3525 90 6 196 274 65,5 65 65,5 178 28,8 50 1 25 212 - 32 7 95 5,4 10 3535 90 6 196 274 53,5 89 53,5 178 31,5 65 7 44 - - 45 1 124 5,5 2 2517 65 7 44 297 - 45 1 120 7,8 3020 75 2 63 204 - 51 12 - 7,7 3 3020 75 8 63 297 6 51 6 145 10,5 4 3020 75 2 82 204 - 51 31 - 19,6 4 3525 90 6 82 297 8,5 65 8,5 178 15,6 5 3525 90 4 101 204 18 65 18 - 20,8 4 3535 90 7 82 297 3,5 89 3,5 178 18,3 5 3535 90 2 101 204 - 89 12 - 21,7 5 3525 90 8 101 297 18 65 18 178 16,8 6 3525 90 4 120 204 27,5 65 27,5 - 22,5 5 3535 90 8 101 297 6 89 6 178 19,5 6 3535 90 4 120 204 15,5 89 15,5 - 23,3 6 3525 90 8 120 297 27,5 65 27,5 178 19,3 8 3525 90 4 158 204 46,5 65 46,5 - 26 6 3535 90 8 120 297 15,5 89 15,5 178 22 8 3535 90 4 158 204 34,5 89 34,5 - 27,5 8 3525 90 8 158 294 46,5 65 46,5 178 25,5 10 3525 90 4 196 204 65,5 65 65,5 - 26,6 8 3535 90 8 158 294 34,5 89 34,5 178 28,2 10 3535 90 4 196 204 46 89 61 - 29,3 10 4030 100 8 196 294 60 76 60 216 2 2517 65 7 44 224 0,5 45 0,5 124 6,2 10 4040 100 8 196 294 47 102 47 216 36 3 3020 75 6 63 224 6 51 6 159 8 2 3020 75 7 44 309 3,5 51 3,5 159 8,7 4 3020 75 6 82 224 159 9,5 3 3020 75 8 63 309 6 51 6 159 10,8 5 3525 90 6 101 224 178 17 4 3525 90 8 82 309 8,5 65 8,5 178 15,9 6 3525 90 6 120 224 27,5 65 27,5 178 16,7 4 3535 90 7 82 309 3,5 89 3,5 178 18,6 8 3525 90 6 158 224 46,5 65 46,5 178 24 5 3525 90 8 101 309 18 65 18 178 18,1 1 2012 50 7 25 242 - 32 7 95 6,1 5 3535 90 8 101 309 6 89 6 178 20,8 2 2517 65 7 44 242 0,5 45 0,5 124 6,8 6 3525 90 6 120 309 27,5 65 27,5 178 20,1 3 3020 75 8 63 242 6 51 6 159 8,6 6 3535 90 6 120 309 15,5 89 15,5 178 22,8 4 3020 75 6 82 242 159 10,1 8 3525 90 8 158 317 46,5 65 46,5 178 24,3 5 3525 90 6 101 239 18 65 18 178 15,1 8 3535 90 8 158 317 34,5 89 34,5 178 5 3535 90 6 101 239 6 89 6 178 17,8 10 4030 100 8 196 317 60 76 6 3525 90 6 120 239 27,5 65 27,5 178 16,9 10 4040 100 8 196 317 47 6 3535 90 6 120 239 15,5 89 15,5 178 19,6 2 3020 75 7 44 335 3,5 8 3525 90 6 158 239 46,5 65 46,5 178 24,5 3 3020 75 8 63 335 6 8 3535 90 6 158 239 34,5 89 34,5 - 26,7 4 3525 90 8 82 335 8,5 10 3525 90 6 196 239 65,5 65 65,5 - 27,8 5 3525 90 8 101 335 18 10 3535 90 6 196 239 1 2012 50 7 25 2 2517 65 7 3 3020 75 4 3020 75 5 3525 5 3535 6 15,5 51 15,5 15,5 51 15,5 18 65 18 15,5 51 15,5 335 355 375 32 27 60 216 33,5 102 47 216 38 51 3,5 159 9,5 51 6 159 11,5 65 8,5 178 16,5 65 18 178 21 46 89 61 - 30,5 6 3525 90 8 120 335 27,5 65 27,5 178 25 262 - 32 7 95 6,8 8 3525 90 8 158 335 46,5 65 46,5 178 28 44 262 0,5 45 0,5 124 7,3 8 63 262 6 51 6 159 9,2 6 82 262 159 14,3 90 6 101 259 18 65 18 178 15,5 90 6 101 259 6 89 6 178 18,2 3525 90 6 120 259 27,5 65 27,5 178 19,2 6 3535 90 6 120 259 15,5 89 15,5 178 21,9 8 3525 90 6 158 259 46,5 65 46,5 178 23,5 8 3535 90 6 158 259 34,5 89 34,5 178 26,2 15,5 51 15,5 38 V- Belts and V- Belt Pulleys Chapter 11 SPB DM Groove 400 2 Bush no 3020 3 3525 90 3 3535 4 3525 4 425 450 475 500 Max Fig Bore 75 7 B J K L M N 44 354 3,5 51 3,5 159 10 7 63 354 1 65 1 178 15,6 90 7 63 354 13 89 13 178 18,3 90 8 82 354 8,5 65 8,5 178 17,8 3535 90 7 82 354 3,5 89 3,5 178 20,5 5 3525 90 8 101 354 18 65 18 178 20,7 5 3535 90 8 101 354 6 89 6 178 23,4 6 3525 90 8 120 354 27,5 65 27,5 178 22,4 6 3535 90 8 120 354 15,5 89 15,5 178 25,1 8 4030 90 8 158 362 41 76 41 216 32 8 4040 100 8 158 362 28 102 28 216 36,5 10 4030 100 8 196 362 60 76 60 216 36 10 4040 100 8 196 362 47 102 47 216 41 2 3020 75 7 44 381 3,5 51 3,5 159 11,5 3 3525 90 7 63 381 1 65 1 178 18 4 3525 90 8 82 381 8,5 65 8,5 178 19,5 5 3525 90 8 101 381 18 65 18 178 6 3525 90 8 120 381 27,5 65 27,5 178 25,1 8 4030 100 8 158 381 34,5 89 34,5 216 35,1 2 3020 75 7 44 410 3,5 51 3,5 159 12,1 3 3525 90 7 63 410 - 65 2 178 19,2 3 3535 90 7 63 410 13 89 13 178 21,9 4 3525 90 8 82 410 - 65 17 178 21,8 4 3535 90 7 82 410 3,5 89 3,5 178 24,5 5 3525 90 8 101 410 - 65 36 178 24,6 5 3535 90 8 101 410 6 89 6 178 27,3 6 4030 100 8 120 410 22 76 22 216 31 6 4040 100 8 120 410 9 102 9 216 35,5 8 4030 100 8 158 410 41 76 41 216 36 8 4040 100 8 158 410 28 102 28 216 40,9 10 4535 110 8 196 410 53,5 10 4545 110 8 196 410 40,5 115 40,5 242 2 3020 75 7 44 431 3,5 51 3,5 159 13 3 3525 90 7 63 431 1 65 1 178 20 4 3525 90 8 82 431 8,5 65 8,5 178 22,5 5 3525 90 8 101 431 18 65 18 178 26,5 6 4030 100 8 120 431 15,5 89 15,5 216 33,5 8 4030 100 8 158 431 34,5 89 34,5 216 39,5 2 3020 75 7 44 454 3,5 51 3,5 159 13,2 3 3525 90 7 63 454 - 65 2 178 20,4 3 3535 90 7 63 454 13 89 13 178 23,1 4 3525 90 8 82 454 - 65 17 178 23,9 4 3535 90 7 82 454 3,5 89 3,5 178 26,6 5 3525 90 8 101 454 - 65 36 178 3,5 5 3535 90 8 101 454 6 89 6 178 29,9 6 4030 100 8 120 454 22 76 22 216 34 6 4040 100 8 120 454 9 102 9 216 38,9 8 4030 100 8 158 460 41 76 41 216 40,5 28 102 28 216 45,5 89 53,5 242 Weight Groove 530 2 Bush no 3020 3 3525 90 7 4 3525 90 5 3525 6 4030 8 4030 2 3020 3 3 560 23 630 47 53,5 8 4040 100 8 158 460 10 4535 110 8 196 460 53,5 53,5 242 55 10 4545 110 8 196 460 40,5 115 40,5 242 61 89 DM 710 Max Fig Bore 75 7 B J K L M N Weight 44 484 3,5 51 3,5 159 14,2 63 484 1 65 1 178 22 8 82 484 8,5 65 8,5 178 24,5 90 8 101 484 18 65 18 178 100 8 120 484 15,5 89 15,5 216 100 8 158 484 34,5 89 34,5 216 75 7 44 525 3,5 51 3,5 159 16,5 3525 90 7 63 525 - 65 2 178 23,2 3535 90 7 63 525 - 89 26 178 25,9 4 3525 90 8 82 525 - 65 17 178 26,3 4 3535 90 7 82 525 - 89 7 178 5 4030 100 8 101 525 12,5 76 12,5 216 32,5 5 4040 100 7 101 525 0,5 102 0,5 216 35,3 6 4030 100 8 120 525 22 76 22 216 38 6 4040 100 8 120 525 9 102 9 216 43,1 8 4535 110 8 158 525 34,5 34,5 242 44,5 8 4545 110 8 158 525 21,5 115 21,5 242 2 3020 75 7 44 584 3 3525 90 7 63 3 3535 90 7 63 4 3525 90 8 4 3535 90 5 4030 5 89 3,5 51 584 - 584 13 82 584 7 82 584 100 4040 6 28 35,5 42 29 49 3,5 146 18,5 65 2 178 26,2 89 13 178 28,9 - 65 17 178 30,6 3,5 89 3,5 178 33,3 8 101 584 12,5 76 12,5 216 38,5 100 7 101 584 0,5 102 0,5 216 43,1 4030 100 8 120 584 22 76 22 216 44 6 4040 100 8 120 584 9 102 9 216 49,2 8 4535 110 8 158 590 34,5 34,5 242 57 8 4545 110 8 158 590 21,5 115 21,5 242 62 10 4535 110 8 196 590 53,5 53,5 242 66 10 4545 110 8 196 590 40,5 115 40,5 242 72 2 3030 75 7 44 670 16 76 16 145 23 3 3525 90 7 63 670 1 65 1 180 30,5 3 3535 90 7 63 670 13 89 13 180 33,2 4 3525 90 8 82 670 8,5 65 8,5 180 36,4 4 3535 90 7 82 670 3,5 89 3,5 180 39,1 5 4030 100 8 101 670 12,5 76 12,5 215 5 4040 100 7 101 670 102 0,5 6 4535 110 8 120 670 15,5 89 15,5 242 6 4545 110 8 120 670 2,5 115 2,5 242 62,3 8 4535 110 8 158 670 34,5 89 34,5 242 65,5 8 4545 110 8 158 670 21,5 115 21,5 242 71 10 4535 110 8 196 670 53,5 53,5 242 75 10 4545 110 8 196 670 40,5 115 40,5 242 80 0,5 89 89 89 215 46 50,2 57 39 V- Belts and V- Belt Pulleys Chapter 11 SPB DM Groove 800 2 2 3 3 4 4 5 5 6 6 8 8 10 10 3 3 4 4 5 5 6 6 8 8 10 10 3 3 4 4 5 5 6 6 8 8 10 10 3 4 5 6 8 900 1000 1250 Bush no 3525 3535 3525 3535 4030 4040 4030 4040 4535 4545 4535 4545 4535 4545 3525 3535 4030 4040 4535 4545 4535 4545 4535 4545 5040 5050 4030 4040 4030 4040 4535 4545 4535 4545 4535 5050 5040 5050 4040 4545 4545 5050 5050 Max Bore 90 90 90 90 100 100 100 100 110 110 110 110 110 110 90 90 100 100 110 110 110 110 110 110 125 125 100 100 100 100 110 110 110 110 110 125 125 125 100 110 110 125 125 Fig B J K L M N Weight 7 7 7 7 8 7 8 7 8 8 8 8 8 8 7 7 8 7 8 7 8 8 8 8 8 8 7 7 8 7 8 7 8 8 8 8 8 8 7 7 7 7 8 44 44 63 63 82 82 101 101 120 120 158 158 196 196 63 63 82 82 101 101 120 120 158 158 196 196 63 63 82 82 101 101 120 120 158 158 196 196 63 82 101 120 158 760 760 760 760 760 760 760 760 760 760 760 760 760 760 858 858 858 858 858 858 858 858 858 858 858 858 958 958 958 958 958 958 958 958 958 958 958 958 1208 1208 1208 1208 1208 10,5 22,5 13 10 19 0,5 15,5 2,5 34,5 21,5 53,5 40,5 1 13 3 10 6 7 15,5 2,5 34,5 21,5 47 34,5 6,5 19,5 3 10 6 7 15,5 2,5 34,5 15,5 47 34,5 19,5 16,5 7 3,5 15,5 65 89 65 89 76 102 76 102 89 115 89 115 89 115 65 89 76 102 89 115 89 115 89 115 102 127 76 102 76 102 89 115 89 115 89 127 102 127 102 115 115 127 127 10,5 22,5 2 13 6 10 6 0,5 15,5 2,5 34,5 21,5 53,5 40,5 1 13 3 10 6 7 15,5 2,5 34,5 21,5 47 34,5 6,5 19,5 3 10 6 7 15,5 2,5 34,5 15,5 47 34,5 19,5 16,5 7 3,5 15,5 180 180 180 180 216 216 216 216 242 242 242 242 242 242 180 180 216 216 242 242 242 242 242 242 257 267 216 216 216 216 242 242 242 242 242 267 267 267 216 242 242 190 267 27,1 29,8 34 36,7 43,8 48,8 51,1 56,1 64,9 71,4 84,4 90,9 96 102 44,1 46,8 55 60 67,5 74,8 74,5 81,5 103,5 110 119 126 52 56,5 61,5 66,5 74 80,5 84 90 111,5 132 141 147 120 152 175 267 232 40 V- Belts and V- Belt Pulleys Chapter 11 SPC Ordering code is composed as follow: SPC 300-6/3525 SPC Section 300 Pulley diameter 6 Number of grooves 3525 Bush size DM Groove 200 3 4 5 5 6 6 8 8 3 4 5 5 6 6 8 8 2 3 4 4 5 5 6 6 8 8 3 4 4 5 5 6 6 8 8 2 3 4 4 5 5 6 6 8 8 212 224 236 250 Bush no 2517 3020 3525 3535 3525 3535 3525 3535 3020 3020 3525 3535 3525 3535 3525 3535 3020 3020 3525 3535 3525 3535 3525 3535 3525 3535 3020 3525 3535 3525 3535 3525 3535 3525 3535 3020 3020 3525 3535 3525 3535 3525 3535 3525 3535 Max Bore 65 75 90 90 90 90 90 90 75 75 90 90 90 90 90 90 75 75 90 90 90 90 90 90 90 90 75 90 90 90 90 90 90 90 90 75 75 90 90 90 90 90 90 90 90 Fig B J K L M N Weight DM Groove 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 85 110,5 136 136 161,5 161,5 212,5 212,5 85 110,5 136 136 161,5 161,5 212,5 212,5 59,5 85 110,5 110,5 136 136 161,5 161,5 212,5 212,5 85 110,5 110,5 136 136 161,5 161,5 212,5 212,5 59,5 85 110,5 110,5 136 136 161,5 161,5 212,5 212,5 151 151 151 151 151 151 151 151 163 163 163 163 163 163 163 163 170 170 170 170 170 170 170 170 170 170 182 182 182 182 182 182 182 182 182 170 200 200 200 200 200 200 200 200 200 20 29,8 35,5 16 48,3 15,8 73,8 45,8 17 29,8 35,5 16 48,3 36,3 73,8 45,8 4,3 17 22,8 10,8 35,5 23,5 48,3 36,3 73,8 45,8 17 22,8 10,8 35,5 23,5 48,3 36,3 73,8 45,8 4,1 17 22,8 10,8 35,5 23,5 48,3 36,3 73,8 61,8 45 51 65 89 65 89 65 89 51 51 65 89 65 89 65 89 51 51 65 89 65 89 65 89 65 89 51 65 89 65 89 65 89 65 89 51 51 65 89 65 89 65 89 65 89 20 29,8 35,5 31 48,3 56,8 73,8 77,8 17 29,8 35,5 31 48,3 36,3 73,8 77,8 4,3 17 22,8 10,8 35,5 23,5 48,3 36,3 73,8 77,8 17 22,8 10,8 35,5 23,5 48,3 36,3 73,8 77,8 4,5 17 22,8 10,8 35,5 23,5 48,3 36,3 73,8 61,8 - 9 10,5 11,3 14 14,3 17 20,3 23 10 12,5 12,4 15 15,5 18 21,3 24 8,1 11 11,3 14 13,5 16,2 16,3 19 22,2 24,9 12 14,5 17,2 16,4 19,1 18,1 20,8 22,8 25,5 9,8 14,5 18 20,7 20,1 22,8 23,3 26 26,9 29,7 265 3 3 4 4 5 5 6 6 8 8 3 3 4 4 5 5 6 6 8 8 3 3 4 4 5 5 6 6 8 8 3 3 4 4 5 5 6 6 8 8 3 3 4 4 5 5 6 6 8 8 280 300 315 335 Bush no 3525 3535 3525 3535 3525 3535 3525 3535 3525 3535 3525 3535 3525 3535 3525 3535 3525 3535 3525 3535 3525 3535 3525 3535 3525 3535 3525 3535 4030 4040 3525 3535 3525 3535 3525 3535 3525 3535 4030 4040 3525 3535 3525 3535 3525 3535 3525 3535 4030 4040 Max Fig B Bore 90 4 85 90 1 85 90 6 110,5 90 6 110,5 90 6 136 90 6 136 90 6 161,5 90 6 161,5 90 6 212,5 90 6 212,5 90 6 85 90 1 85 90 6 110,5 90 6 110,5 90 6 136 90 6 136 90 6 161,5 90 6 161,5 90 4 212,5 90 6 212,5 90 6 85 90 5 85 90 6 110,5 90 6 110,5 90 6 136 90 6 136 90 6 161,5 90 6 161,5 100 4 212,5 100 4 212,5 90 6 85 90 5 85 90 6 110,5 90 6 110,5 90 6 136 90 6 136 90 6 161,5 90 6 161,5 100 6 212,5 100 4 212,5 90 6 85 90 5 85 90 6 110,5 90 6 110,5 90 6 136 90 6 136 90 6 161,5 90 6 161,5 100 6 212,5 100 6 212,5 J 215 215 215 215 215 215 215 215 215 215 230 230 230 230 230 230 230 230 230 230 250 250 250 250 250 250 250 250 250 250 265 265 265 265 265 265 265 265 265 265 282 282 282 282 282 282 282 282 282 282 K L M N 10 65 10 178 89 4 178 22,8 65 22,8 178 10,8 89 10,8 178 35,5 65 35,5 178 23,5 89 23,5 178 48,3 65 48,3 178 36,3 89 36,3 178 73,8 65 73,8 178 61,8 89 61,8 178 10 65 10 178 89 4 178 22,8 65 22,8 178 10,8 89 10,8 178 35,5 65 35,5 178 23,5 89 23,5 178 48,3 65 48,3 178 36,3 89 36,3 178 73,8 65 73,8 61,8 89 61,8 178 10 65 10 178 2 89 2 178 22,8 65 22,8 178 10,8 89 10,8 178 35,5 65 35,5 178 23,5 89 23,5 178 48,3 65 48,3 178 36,3 89 36,3 178 68,3 76 68,3 55,3 102 55,3 10 65 10 178 2 89 2 178 22,8 65 22,8 178 10,8 89 10,8 178 35,5 65 35,5 178 23,5 89 23,5 178 48,3 65 48,3 178 36,3 89 36,3 178 68,3 76 68,3 200 55,3 102 55,3 200 10 65 10 178 2 89 2 178 22,8 65 22,8 178 10,8 89 10,8 178 35,5 65 35,5 178 23,5 89 23,5 178 48,3 65 48,3 178 36,3 89 36,3 178 68,3 76 68,3 200 55,3 102 55,3 200 Weight 18,5 21,2 21,3 24 23,5 26,2 26,3 29 30,6 33,3 21,3 24 26,3 29 28,3 31 59,4 33,8 34,8 37,5 18,3 21 22,3 25 25,8 28,5 52,1 29 41,5 41,5 18,9 21,6 21,9 24,6 26,3 29 28,7 31,4 45,5 50 19,8 22,5 23,8 26,5 27,2 30 32,3 35 53 58 41 V- Belts and V- Belt Pulleys Chapter 11 SPC DM Groove 355 3 Bush no 3525 3 3535 90 4 3525 4 5 375 400 425 450 Max Fig Bore 90 6 B J K L M N Weight DM Groove 85 305 10 65 10 178 20,2 475 3 Bush no 3525 Max Fig Bore 90 8 5 85 305 2 89 2 178 22,9 3 3535 90 90 6 110,5 305 22,8 65 22,8 178 45,8 4 3525 3535 90 6 110,5 305 10,8 89 10,8 178 28,3 4 3525 90 6 136 305 35,5 65 35,5 178 29,8 5 5 3535 90 6 136 305 23,5 89 23,5 178 32,5 6 3525 90 6 161,5 305 48,3 65 48,3 178 6 3535 90 6 161,5 305 36,3 89 36,3 178 8 4030 100 6 212,5 305 68,3 76 8 4040 100 6 212,5 3 3525 90 6 85 322 10 65 10 178 21,1 3 3535 90 5 85 322 2 89 2 178 23,8 4 3525 90 6 110,5 322 22,8 65 22,8 178 4 3535 90 6 110,5 322 10,8 89 5 3525 90 6 136 322 35,5 5 3535 90 6 136 6 4030 100 6 6 4040 100 6 8 4535 110 8 4545 110 3 3525 3 3535 4 B J K L M N Weight 85 422 10 65 10 178 37,2 7 85 422 2 89 2 178 90 8 110,5 422 22,8 65 22,8 178 44,3 3535 90 8 110,5 422 10,8 89 10,8 178 47 4030 100 8 136 422 30 76 30 216 43 5 4040 100 8 136 422 17 102 17 216 47,2 33,3 6 4535 110 6 161,5 422 36,3 36 6 4545 110 6 161,5 422 23,3 115 23,3 242 68,3 200 62,5 8 5040 125 6 212,5 422 55,3 102 55,3 265 76 305 55,3 102 55,3 200 67,5 8 5050 125 6 212,5 422 42,8 127 42,8 265 81,5 3 3525 90 8 85 450 10 65 10 178 28,2 3 3535 90 7 85 450 2 89 2 178 30,9 27,3 4 3525 90 8 110,5 450 22,8 65 22,8 178 36,3 10,8 178 30 4 3535 90 8 110,5 450 10,8 89 10,8 178 39 65 35,5 178 30,3 5 4030 100 8 136 450 30 76 30 216 44 322 23,5 89 23,5 178 33 5 4040 100 8 136 450 17 102 17 216 48,7 161,5 322 42,8 76 42,8 216 40,5 6 4535 110 8 161,5 450 36,3 161,5 322 29,8 102 29,8 216 45,5 6 4545 110 8 161,5 450 23,3 115 23,3 242 6 212,5 322 61,8 61,8 225 62 8 5040 125 6 212,5 450 55,3 102 55,3 265 82 6 212,5 322 48,8 115 48,8 225 68 8 5050 125 6 212,5 450 42,8 127 42,8 265 87,4 90 6 85 350 10 65 10 178 21,4 3 3525 90 8 85 480 10 65 10 178 32,3 90 7 85 350 2 89 2 178 24,1 3 3535 90 7 85 480 2 89 2 178 35 3525 90 8 110,5 350 22,8 65 22,8 178 25,3 4 4030 100 8 110,5 480 17,3 76 17,3 216 35 4 3535 90 8 110,5 350 10,8 89 10,8 178 28 4 4040 100 8 110,5 480 4,3 102 4,3 216 40 5 3525 90 8 136 350 35,5 65 35,5 178 31,3 5 4535 110 8 136 480 23,5 89 23,5 242 55 5 3535 90 8 136 350 23,5 89 23,5 178 34 5 4545 110 8 136 480 115 6 4030 100 6 161,5 350 42,8 76 42,8 216 43 6 5040 125 8 6 4040 100 6 161,5 350 29,8 102 29,8 216 48 6 5050 125 8 4535 110 6 212,5 350 61,8 59,5 8 5040 8 4545 110 6 212,5 350 48,8 115 48,8 240 65 8 3 3525 90 8 85 372 10 65 3 3535 90 7 85 372 2 89 4 3525 90 8 110,5 372 22,8 65 22,8 178 4 3535 90 8 110,5 372 10,8 89 10,8 178 5 4030 100 6 136 372 30 76 30 216 5 4040 100 6 136 372 17 102 17 216 6 4535 110 6 161,5 372 36,3 6 4545 110 6 161,5 8 4535 110 6 8 4545 110 3 3525 3 89 89 61,8 240 10 178 2 178 23,3 500 530 560 11 89 89 36,3 242 36,3 242 11 40 56 62,8 54 60,2 242 60 161,5 480 29,8 102 29,8 265 67 8 161,5 480 17,3 127 17,3 265 73 125 6 212,5 480 55,3 102 55,3 265 87 5050 125 6 212,5 480 42,8 127 42,8 265 3 3525 90 8 85 510 10 65 510 2 89 10 178 2 178 94 33,3 26 3 3535 90 7 85 28,3 4 4030 100 8 110,5 510 17,3 76 31 4 4040 100 8 110,5 510 4,3 102 4,3 216 50 40,1 5 4535 110 8 136 510 23,5 89 23,5 242 57 45 5 4545 110 8 136 510 115 52,5 6 5040 125 8 372 23,3 115 23,3 242 58 6 5050 125 212,5 372 61,8 61,8 242 68 8 5040 6 212,5 372 42,8 115 42,8 242 74 8 90 8 85 400 10 65 10 178 25,9 3535 90 7 85 400 2 89 2 178 4 3525 90 8 110,5 400 22,8 65 4 3535 90 8 110,5 400 10,8 89 5 4030 100 8 136 400 30 76 5 4040 100 8 136 400 17 102 6 4535 110 6 161,5 400 36,3 6 4545 110 6 161,5 8 5040 125 6 212,5 8 5050 125 6 212,5 89 89 63 161,5 510 29,8 102 29,8 242 71 8 161,5 510 17,3 127 17,3 265 77 125 8 212,5 510 55,3 102 55,3 265 87 5050 125 8 212,5 510 42,8 127 42,8 265 94 3 4030 100 8 85 580 4,5 76 4,5 216 44 28,6 3 4040 100 7 85 580 8,5 102 8,5 216 48,5 22,8 178 30,8 4 4535 110 8 110,5 580 10,8 89 10,8 242 10,8 178 33,5 4 4545 110 7 110,5 580 2,2 115 2,2 242 61 136 580 17 102 17 267 70,5 580 4,5 127 4,5 267 630 11 36 45,5 242 36,3 242 11 17,3 216 55 30 216 39,5 5 5040 125 8 17 216 45 5 5050 125 8 136 36,3 242 55 6 5040 125 8 161,5 580 29,8 102 29,8 267 400 23,3 115 23,3 242 61,1 6 5050 125 8 161,5 580 17,3 127 17,3 267 86 400 55,3 102 55,3 265 72 8 5040 125 8 212,5 580 55,3 102 55,3 265 98,5 400 42,8 127 42,8 265 78,7 8 5050 125 8 212,5 580 42,8 127 42,8 265 105,5 89 77 79,5 42 V- Belts and V- Belt Pulleys Chapter 11 SPC DM 710 800 900 1000 1250 Groove 3 3 4 4 5 5 6 6 8 8 3 3 4 4 5 5 6 6 8 8 3 3 4 4 5 5 6 6 8 8 3 3 4 4 5 5 6 6 8 8 3 4 5 6 8 Bush no 4030 4040 4535 4545 5040 5050 5040 5050 5040 5050 4535 4545 5040 5050 5040 5050 5040 5050 5040 5050 4535 4545 5040 5050 5040 5050 5040 5050 5040 5050 5040 5050 5040 5050 5040 5050 5040 5050 5040 5050 5050 5050 5050 5050 5050 Max Bore 100 100 110 110 125 125 125 125 125 125 110 110 125 125 125 125 125 125 125 125 110 110 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 125 Fig 8 7 8 7 8 8 8 8 8 8 7 7 8 7 8 8 8 8 8 8 7 7 8 7 8 8 8 8 8 8 7 7 8 7 8 8 8 8 8 8 7 7 8 8 8 B 85 85 110,5 110,5 136 136 161,5 161,5 212,5 212,5 85 85 110,5 110,5 136 136 161,5 161,5 212,5 212,5 85 85 110,5 110,5 136 136 161,5 161,5 212,5 212,5 85 85 110,5 110,5 136 136 161,5 161,5 212,5 212,5 85 110,5 136 161,5 212,5 J 667 667 667 667 667 667 667 667 667 667 737 737 737 737 737 737 737 737 737 737 847 847 847 847 847 847 847 847 847 847 937 937 937 937 937 937 937 937 937 937 1187 1187 1187 1187 1187 K 10 8,5 10,8 2,2 17 4,5 29,8 17,3 55,3 42,8 2 15 4,3 8,2 17 4,5 29,8 17,3 55,3 42,8 2 15 4,3 8,2 17 4,5 29,8 17,3 55,3 42,8 8,5 21 4,3 8,2 17 4,5 29,8 17,3 55,3 42,8 21 8,2 4,5 17,3 42,8 L 65 102 89 115 102 127 102 127 102 127 89 115 102 127 102 127 102 127 102 127 89 115 102 127 102 127 102 127 102 127 102 127 102 127 102 127 102 127 102 127 127 127 127 127 127 M 10 8,5 10,8 2,2 17 4,5 29,8 17,3 55,3 42,8 2 15 4,3 8,2 17 4,5 29,8 17,3 55,3 42,8 2 15 4,3 8,2 17 4,5 29,8 17,3 55,3 42,8 8,5 21 4,3 8,2 17 4,5 29,8 17,3 55,3 42,8 21 8,2 4,5 17,3 42,8 N 216 216 242 242 267 267 267 267 267 267 242 242 267 267 267 267 267 267 267 267 242 242 267 267 267 267 267 267 267 267 267 267 267 267 267 267 267 267 267 267 267 267 267 267 267 Weight - 43 V- Belts and V- Belt Pulleys Chapter 11 V- Belt Pulleys with Solid Hub A2 The pulleys conform to ISO 4183 and DIN 2211. B=E(n-1)+2F n=No. og grooves Dimensions in milimetres Material: Fine grain cast- iron grade 220-260 Eccentricity of O/ D to bore DIN 2211 part 1 Groove side wobble tolerance: DIN 2211 part 1 Surface roughness: ISO 254 Balance quality grade: ISO 1940 Dynamic balancing can be supplied to order. Keyway: BS4235 - DIN 6885 or BS46, standard tole- rance P9 Bore: Standard tolerance H7 A2 V- belt pulleys- with solid hub Profil Dm α br E F C t SPZ ≤ 80 > 80 34 38 8,5 12,0 8,0 2,0 11,0 SPA ≤ 118 > 118 34 38 11,0 15,0 10,0 2,8 13,8 SPB ≤ 190 > 190 34 38 14,0 19,0 12,5 3,5 17,5 SPC ≤ 315 > 315 34 38 19,0 25,5 19,0 9,5 23,8 44 V- Belts and V- Belt Pulleys Chapter 11 SPZ Ordering code is composed as follow: SPZ 125-3/ solid hub SPZ Section 125 Pulley diameter 3 Number of grooves Fig. K = Plate Pulley Fig. A = Arm Pulley Dm 45 50 56 63 71 75 80 85 90 95 100 106 112 118 125 Groove 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 N 30 30 30 30 30 30 35 35 35 42 42 42 42 42 50 42 42 50 42 50 50 42 50 50 42 50 60 50 50 60 50 50 60 55 50 60 50 60 60 50 60 60 50 60 65 L 24 35 35 24 35 40 24 35 40 24 35 40 24 35 40 24 35 40 24 35 35 24 35 35 24 35 38 24 35 38 24 35 38 24 35 38 24 35 38 24 35 38 24 35 40 Fig. 2k 2k 5k 2k 2k 1k 2k 2k 1k 2k 2k 1k 2k 2k 1k 2k 2k 1k 2k 2k 5k 2k 2k 5k 2k 2k 5k 2k 2k 5k 2k 2k 5k 2k 2k 5k 2k 2k 5k 2k 2k 5k 2k 2k 1k B 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 Weight 0,2 0,3 0,4 0,3 0,4 0,5 0,3 0,4 0,6 0,3 0,6 0,8 0,3 0,6 1 0,3 0,6 1 0,3 0,6 1,1 0,3 0,7 1,1 0,3 0,7 1,1 0,4 0,8 1,2 0,4 0,9 1,2 0,5 0,9 1,3 0,5 1 1,4 0,6 1,1 1,4 0,7 1,2 1,5 Dm 132 140 150 160 170 180 190 200 212 225 250 280 315 355 400 Groove 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 2 3 N 55 60 65 55 65 65 55 65 65 60 65 70 60 65 70 60 65 70 65 65 70 65 65 75 65 65 75 70 70 75 70 70 75 70 70 80 70 75 80 70 75 85 80 85 L 24 35 40 24 38 40 24 38 40 30 38 40 30 38 40 30 38 40 30 38 40 38 38 40 30 38 40 38 38 40 38 38 40 34 38 40 34 38 40 34 40 45 40 45 Fig. 2k 2k 1k 2k 2k 1k 2a 2k 1k 2a 2a 1a 2a 2a 1a 2a 2a 1a 2a 2a 1a 2a 2a 1a 2a 2a 1a 2a 2a 1a 2a 2a 1a 2a 2a 1a 2a 2a 1a 2a 2a 2a 2a 2a B 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 16 28 40 28 40 Weight 0,8 1,3 1,6 0,9 1,4 1,6 1 1,5 1,8 1,2 1,6 2,4 1,6 1,8 3 2,1 2 3,5 2,2 2,3 4 2,4 2,8 4,4 2,6 3,4 5 2,8 4 5,3 3,3 4,8 6 3,8 5,2 7 4,3 6,8 8,2 4,6 8 10 10 11,7 45 V- Belts and V- Belt Pulleys Chapter 11 SPA Ordering code is composed as follow: SPA 100-2/ solid hub SPA Section 100 Pulley diameter 2 Number of grooves Fig. K = Plate Pulley Fig. A = Arm Pulley * Dm +4mm/ F + 1mm type 40 50 56 63 71 75 80 85 90 95 100 Groove 1 2 1 2 3 1 2 3 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 N 35 35 35 35 35 35 35 35 42 42 42 45 50 42 42 42 45 50 42 42 46 45 50 42 42 46 50 55 42 50 50 50 55 50 50 52 50 55 50 50 52 55 60 50 50 52 55 60 L 34 49 34 49 47 34 49 47 34 49 47 60 70 34 49 42 60 70 34 49 42 60 82 34 49 42 60 55 34 49 42 53 55 34 49 42 53 67 34 49 42 53 67 34 49 42 53 60 Fig. 2k 2k 2k 2k 5k 2k 2k 5k 2k 2k 5k 5k 5k 2k 2k 5k 5k 5k 2k 2k 5k 5k 1k 2k 2k 5k 5k 5k 2k 2k 5k 5k 5k 2k 2k 5k 5k 5k 2k 2k 5k 5k 5k 2k 2k 5k 5k 5k B 20 35 20 35 50 20 35 50 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 weight 0,2 0,3 0,3 0,4 0,5 0,4 0,6 0,7 0,5 0,7 0,8 1,2 1,4 0,5 0,8 0,9 1,4 1,8 0,5 1 1 1,7 1,9 0,5 1 1,1 1,8 2 0,6 1,2 1,4 1,9 2,2 0,8 1,4 1,6 2,2 2,5 0,7 1,5 1,8 2,4 2,7 0,8 1,3 1,9 2,7 3,1 type 106 112 118 125 132 140 150 160 170 180 Groove 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 N 50 50 55 55 60 50 50 55 55 60 50 60 60 55 60 55 60 60 60 65 55 60 60 60 65 60 60 60 60 65 60 60 60 60 65 60 60 60 60 65 60 60 60 60 65 65 63 70 70 75 L 34 49 42 53 60 34 49 42 53 60 34 49 42 53 65 34 49 42 53 65 34 49 42 53 65 34 49 42 53 65 36 49 42 53 65 36 49 42 60 70 36 49 42 60 70 36 49 42 60 70 Fig. 2k 2k 5k 5k 5k 2k 2k 5k 5k 5k 2k 2k 5k 5k 5k 2k 2k 5k 5k 5k 2k 2k 5k 5k 5k 2k 2k 5k 5k 5k 2a 2a 5k 5k 5k 2a 2a 5a 5k 5k 2a 2a 5a 5a 5a 2a 2a 5a 5a 5a B 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 weight 0,8 1,6 2,2 3,2 3,8 1 1,7 2,3 3,3 3,9 1,1 1,8 2,4 3,4 4,1 1,3 1,9 2,5 3,4 4,4 1,4 2,2 2,5 3,5 4,7 1,5 2,3 2,6 3,6 4,9 1,6 2,5 2,9 4 5,1 1,7 2,4 2,8 3,6 5,4 2 2,9 3,2 4,2 5,8 2 3,1 3,6 4,6 6,1 46 V- Belts and V- Belt Pulleys Chapter 11 SPA Fig. K = Plate Pulley Fig. A = Arm Pulley * Dm +4mm/ F + 1mm Dm 190 200 212 225 236 250 280 300 315 355 Groove 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 N 65 70 70 75 75 70 75 75 70 75 70 75 75 70 75 70 75 75 75 75 70 75 75 80 80 75 75 80 80 80 75 75 80 85 85 80 80 85 90 90 80 80 85 90 90 80 85 90 90 95 L 36 49 42 60 70 36 49 42 60 70 36 49 42 60 70 36 49 42 60 70 36 49 47 60 70 36 49 47 60 70 44 53 47 60 70 44 53 47 60 70 44 53 47 60 70 44 53 47 60 70 Fig. 2a 2a 5a 5a 5a 2a 2a 5a 5a 5a 2a 2a 5a 5a 5a 2a 2a 5a 5a 5a 2a 2a 5a 5a 5a 2a 2a 5a 5a 5a 2a 2a 5a 5a 5a 2a 2a 5a 5a 5a 2a 2a 5a 5a 5a 2a 2a 5a 5a 5a B 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 20 35 50 67 82 Weight 2 3,2 4 5,2 6,3 2,4 2,8 4,2 4,9 6,4 2,7 3,4 4,4 5,6 6,8 2,7 3,8 4,6 6,5 7,2 3,3 4,1 4,9 6,2 7,5 3,4 4,3 5,3 7 7,8 3,9 5,3 6,5 8,5 9,9 4,2 5,9 7,5 9,8 11,3 4,7 6,6 8,7 11,1 12,5 5,5 7,7 9,5 11,8 13,8 Dm 400 450 500 560 630 Groove *1 *2 *3 *4 *5 *1 *2 *3 *4 *5 *1 *2 *3 *4 *5 *1 *2 *3 *4 *5 *2 *3 *4 *5 N 85 85 95 95 100 90 85 95 100 100 90 90 100 100 100 95 95 100 105 105 100 100 110 110 L 50 53 47 67 82 50 53 47 67 82 50 55 60 67 82 60 60 74 67 82 77 74 80 82 Fig. 2a 2a 5a 1a 1a 2a 2a 5a 1a 1a 2a 2a 2a 1a 1a 2a 2a 2a 1a 1a 2a 2a 2a 1a B 22 37 52 67 82 22 37 52 67 82 22 37 52 67 82 22 37 52 67 82 37 52 67 82 Weight 6,8 8,8 10,5 12,4 15,9 7,5 9,4 12,1 14,2 18,3 10,5 10,7 13,4 16,2 22,8 14 13,1 15,6 19,4 24,5 15,4 19,2 25 28 47 V- Belts and V- Belt Pulleys Chapter 11 SPB Ordering code is composed as follow: FL 200 080/2517 FL Flat belt pulley 200 Pulley diameter 80 Pulley width 2517 Bush size Fig. K = Plate Pulley Fig. A = Arm Pulley * Dm + 5,5mm/ F + 2mm Dm 56 63 71 75 80 85 90 95 100 106 Groove 1 2 3 1 2 3 1 2 3 1 2 3 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 1 2 3 *4 *5 *6 1 2 3 *4 *5 *6 N 42 45 50 45 50 50 45 48 50 45 48 50 50 50 50 52 45 50 50 55 60 60 50 50 55 60 60 50 55 55 60 60 55 55 60 60 65 65 55 55 60 60 65 65 L 41 60 62 41 60 62 41 60 55 41 60 62 41 60 55 70 80 41 60 55 70 75 41 60 55 70 75 41 60 67 70 75 41 60 55 70 75 124 41 60 55 70 75 124 Fig. 2k 2k 5k 2k 2k 5k 2k 2k 5k 2k 2k 5k 2k 2k 5k 5k 5k 2k 2k 5k 5k 5k 2k 2k 5k 5k 5k 2k 2k 2k 5k 5k 2k 2k 5k 5k 5k 1k 2k 2k 5k 5k 5k 1k B 25 44 63 25 44 63 25 44 63 25 44 63 25 44 63 86 105 25 44 63 86 105 25 44 63 86 105 25 44 63 86 105 25 44 63 86 105 124 25 44 63 86 105 124 Weight 0,6 1,0 1,1 0,7 1,2 1,2 0,7 1,3 1,6 0,8 1,4 1,8 1,0 1,6 2,0 2,4 2,7 1,1 1,7 2,1 2,7 3,0 1,1 1,8 2,3 3,0 3,3 1,2 2,0 2,5 2,9 3,6 1,3 2,1 2,8 3,8 4,4 5,2 1,4 2,0 3,0 4,3 5,1 6,0 Dm 112 118 125 132 140 150 160 170 Groove 1 2 3 *4 *5 *6 1 2 3 *4 *5 *6 1 2 3 *4 *5 *6 1 2 3 *4 *5 *6 1 2 3 *4 *5 *6 1 2 3 *4 *5 *6 1 2 3 *4 *5 *6 1 2 3 *4 *5 *6 N 55 55 60 60 70 70 55 55 60 60 70 70 55 55 60 65 70 75 60 60 65 70 70 75 65 65 70 70 75 75 65 70 70 75 75 80 65 70 70 80 80 85 70 70 70 80 85 85 L 41 60 55 67 75 85 41 60 55 70 75 85 41 60 55 70 75 85 41 60 55 70 75 85 41 60 55 70 75 85 43 48 60 70 75 85 43 48 60 70 75 85 43 48 60 70 75 85 Fig. 2k 2k 5k 5k 5k 5k 2k 2k 5k 5k 5k 5k 2k 2k 5k 5k 5k 5k 2k 2k 5k 5k 5k 5k 2k 2k 5k 5k 5k 5k 2k 2k 5k 5k 5k 5k 2a 2a 5a 5k 5k 5k 2a 2a 5a 5k 5k 5k B 25 44 63 86 105 124 25 44 63 86 105 124 25 44 63 86 105 124 25 44 63 86 105 124 25 44 63 86 105 124 25 44 63 86 105 124 25 44 63 86 105 124 25 44 63 86 105 124 Weight 1,5 2,3 3,1 4,7 5,6 6,1 1,5 2,4 3,2 5,2 7,2 6,6 1,6 2,5 3,2 4,7 8,6 8,0 1,8 2,6 3,4 6,3 9,4 8,5 2,1 2,9 3,9 6,9 7,5 11,4 2,4 3,2 4,2 6,7 8,4 12,1 2,5 3,3 4,6 7,0 9,3 12,8 2,8 3,4 4,8 7,2 8,9 13,1 48 V- Belts and V- Belt Pulleys Chapter 11 SPB Fig. K = Plate Pulley Fig. A = Arm Pulley * Dm + 5,5mm/ F + 2mm type 180 190 200 212 225 250 280 300 Groove 1 2 3 *4 *5 *6 1 2 3 *4 *5 *6 1 2 3 *4 *5 *6 1 2 3 *4 *5 *6 1 2 3 *4 *5 *6 1 2 3 *4 *5 *6 1 2 3 *4 *5 *6 1 2 3 *4 *5 *6 N 70 70 75 80 85 90 70 70 75 85 90 95 70 75 75 85 90 95 75 75 80 90 90 95 75 75 80 90 90 95 75 75 80 90 100 100 80 80 90 90 100 100 80 80 90 95 100 100 L 43 48 60 70 75 85 43 48 60 70 75 85 43 48 60 60 80 90 43 48 60 70 80 90 43 48 60 70 90 90 43 55 60 70 80 90 49 55 60 70 80 90 49 55 67 80 80 90 Fig. 2a 2a 5a 5a 5k 5k 2a 2a 5a 5a 5k 5k 2a 2a 5a 5a 5k 5k 2a 2a 5a 5a 5a 5k 2a 2a 5a 5a 5k 5k 2a 2a 5a 5a 5a 5a 2a 2a 5a 5a 5a 5a 2a 2a 2a 5a 5a 5a B 25 44 63 86 105 124 25 44 63 86 105 124 25 44 63 86 105 124 25 44 63 86 105 124 25 44 63 86 105 124 25 44 63 86 105 124 25 44 63 86 105 124 25 44 63 86 105 124 weight 3,1 3,9 5,2 7,4 9 10,8 3,1 4,2 5,4 7,6 9,2 12 3,4 4,4 5,8 7,9 9,5 12,2 3,7 4,6 6,1 7,7 10,3 13,5 4 5,4 6,9 8,6 11,7 14,7 4,2 6,1 8,6 9,8 13,2 17 5,7 7 9,6 11,5 15,5 18 5,9 7,5 10,5 12,4 16,5 18,2 type 315 355 400 450 500 560 630 Groove 1 2 3 *4 *5 *6 1 2 3 *4 *5 *6 *1 *2 *3 *4 *5 *6 *1 *2 *3 *4 *5 *6 *1 *2 *3 *4 *5 *6 *1 *2 *3 *4 *5 *6 *1 *2 *3 *4 *5 *6 N 80 85 90 95 100 100 85 90 95 100 105 110 90 90 95 100 105 110 90 90 95 105 110 115 90 100 100 100 115 120 100 100 100 115 120 120 100 100 100 120 125 130 L 49 55 67 80 80 90 49 55 67 80 75 90 49 55 67 80 85 90 55 55 67 80 80 90 55 59 67 80 80 90 55 55 67 80 80 90 70 80 80 86 90 100 Fig. 2a 2a 2a 5a 5a 5a 2a 2a 2a 5a 5a 5a 2a 2a 1a 5a 5a 5a 2a 2a 1a 5a 5a 5a 2a 2a 1a 5a 5a 5a 2a 2a 1a 5a 5a 5a 2a 2a 2a 1a 5a 5a B 25 44 63 86 105 124 25 44 63 86 105 124 29 48 67 86 105 124 29 48 67 86 105 124 29 48 67 86 105 124 29 48 67 86 105 124 29 48 67 86 105 124 weight 6,4 8,2 12,9 13 17,6 20,6 7 9,7 13,4 18,2 18,7 19,7 8,4 10 14,3 18,5 22,5 28 9,8 10,8 15 20,5 26 28,9 10,7 13,7 15,2 21,3 30 33,8 12,3 15 24,2 26 34,4 39 16,2 20,2 27 30,8 37,2 44 49 V- Belts and V- Belt Pulleys Chapter 11 SPC Ordering code is composed as follow: SPC 400-5/ solid hub SPC Section 400 Pulley diameter 5 Number of grooves Fig. K = Plate Pulley Fig. A = Arm Pulley Dm 100 110 120 130 140 150 160 170 180 190 200 225 250 Groove 1 1 1 1 2 1 2 3 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 5 6 1 2 3 4 5 1 2 3 4 5 6 1 2 3 4 5 6 1 2 3 4 5 6 N 65 65 65 65 65 70 70 70 70 70 70 70 70 70 70 75 75 80 80 80 70 85 85 85 85 95 70 85 85 85 85 70 85 85 90 90 100 80 90 90 95 100 100 90 90 90 95 100 110 L 45 45 45 45 50 45 50 65 45 50 65 80 45 50 65 80 45 50 65 80 54 64 90 95 100 115 54 64 90 95 100 54 64 90 95 100 125 54 64 90 95 100 115 54 64 90 95 100 115 Fig. 2K 2K 2K 2K 5K 2K 5K 5K 2K 5K 5K 5K 2K 5K 5K 5K 2K 5K 5K 5K 2k 1k 1k 5k 5k 5k 2K 2K 1K 5K 5K 2k 1k 1k 5k 5k 5k 2a 1a 1a 5a 5a 5a 2a 1a 1a 5a 5a 5a B 38 38 38 38 64 38 64 90 38 64 90 116 38 64 90 116 38 64 90 116 38 64 90 116 142 168 38 64 90 116 142 38 64 90 116 142 168 38 64 90 116 142 168 38 64 90 116 142 168 Weight 1,8 2,0 2,3 2,6 4,6 2,9 5,0 6,6 3,1 5,3 7,5 10,4 3,7 5,4 9,0 11,6 4,0 6,1 9,6 12,0 4,2 7,2 10,4 10,5 18,0 23,6 4,6 6,7 10,6 11,0 18,5 4,8 7,8 8,8 11,2 15,4 27,0 5,5 7,8 10,6 13,1 16,7 35,0 7,3 8,8 11,0 15,3 19,0 23,7 Dm 280 315 335 355 400 450 500 560 630 Groove 1 2 3 4 5 6 1 2 3 4 5 6 2 3 4 5 6 2 3 4 5 6 2 3 4 5 6 2 3 4 5 6 3 4 5 6 3 4 5 6 3 4 5 6 N 90 95 95 100 105 110 90 95 95 100 105 120 95 95 100 105 120 100 110 110 120 120 110 110 110 120 130 110 120 120 130 130 120 120 130 130 120 120 130 140 130 130 140 140 L 54 64 90 95 100 115 54 74 90 95 100 115 74 90 95 100 115 74 90 95 100 115 80 90 105 100 115 80 90 105 110 120 90 105 110 120 90 105 110 120 90 105 110 120 Fig. 2a 1a 1a 5a 5a 5a 2a 2a 1a 5a 5a 5a 2a 1a 5a 5a 5a 2a 1a 5a 5a 5a 2a 1a 5a 5a 5a 2a 1a 5a 5a 5a 1a 5a 5a 5a 1a 5a 5a 5a 1a 5a 5a 5a B 38 64 90 116 142 168 38 64 90 116 142 168 64 90 116 142 168 64 90 116 142 168 64 90 116 142 168 64 90 116 142 168 90 116 142 168 90 116 142 168 90 116 142 168 Weight 8,7 10,9 15,6 17,5 20,5 27,0 9,1 13,0 17,1 20,0 24,7 31,2 14,0 18,3 22,4 28,3 34,4 15,2 19,2 25,8 32,0 36,2 16,4 20,6 28,0 32,0 45,2 21,1 26,3 31,1 42,2 48,5 28,4 34,1 48,2 52,5 31,1 39,0 54,1 61,5 38,5 48,1 62,2 73,2 50 V- Belts and V- Belt Pulleys Chapter 11 Flat Belt Puleys for Taper Bushes Material: Fine grain cast- iron grade 220-260 Eccentricity of O/ D to bore DIN 7867 Groove side wobble tolerance: DIN 7867 Surface roughness: ISO 254 Balance quality grade: ISO 1940 Pulleys from stock are statically balanced to grade G 6,3 and from 355 mm dynamically balanced to grade G 6,3. Pulleys smaller than 355 mm dynamic balancing can be supplied to order. A4 Flat Belt Pulleys for Taper Bushes/ Poly- V Pulleys A6 Taper Bushes from 1008 to 5050 A5 Weld- on- hubs,bolt- on- hubs and adaptors A4 A5 A6 51 V- Belts and V- Belt Pulleys Chapter 11 Flat Belt Pulleys for Taper Bushes Ordering code is composed as follow: FL 200 080/2517 FL Flat belt pulley 200 Pulley diameter 80 Pulley width 2517 Bush size Fig, • = Solid Pulley Fig, ο = Plate Pulley D1 B Bush No. Part No. L Fig. H Speed 63 80 50 50 80 50 80 100 50 80 100 50 80 100 125 50 80 100 125 50 80 100 125 160 50 80 100 125 160 80 100 125 160 80 100 125 160 80 100 125 160 80 100 125 160 100 125 160 200 100 125 160 200 100 125 160 200 100 125 160 200 160 200 160 200 160 200 160 200 1108 1210 1615 1615 1615 1615 1615 1615 1615 2012 2517 2517 2517 2012 2517 3020 3030 2012 2517 3020 3030 3030 2012 2517 3020 3030 3030 2517 3020 3030 3030 2517 3020 3030 3030 2517 3020 3030 3030 2517 3020 3030 3030 3020 3030 3535 4040 3020 3030 3535 4040 3030 3030 3535 4040 3535 3535 3535 4040 3535 4040 4040 4545 4040 4545 4545 5050 FL063050 FL080050 FL080080 FL090050 FL090080 FL090100 FL100050 FL100080 FL100100 FL125050 FL125080 FL125100 FL125125 FL140050 FL140080 FL140100 FL140125 FL150050 FL150080 FL150100 FL150125 FL150160 FL160050 FL160080 FL160100 FL160125 FL160160 FL180080 FL180100 FL180125 FL180160 FL200080 FL200100 FL200125 FL200160 FL224080 FL224100 FL224125 FL224160 FL250080 FL250100 FL250125 FL250160 FL280100 FL280125 FL280160 FL280200 FL315100 FL315125 FL315160 FL315200 FL355100 FL355125 FL355160 FL355200 FL400100 FL400125 FL400160 FL400200 FL450160 FL450200 FL500160 FL500200 FL560160 FL560200 FL630160 FL630200 22 25 38 38 38 38 38 38 38 32 45 45 45 32 45 51 76 32 45 51 76 76 32 45 51 76 76 45 51 76 76 45 51 76 76 45 51 76 76 45 51 76 76 51 76 89 102 51 76 89 102 76 76 89 102 89 89 89 102 89 102 102 115 102 115 115 127 3• 1• 1• 1• 1• 3• 1• 1• 3• 1• 1• 3• 3• 1• 1• 1• 1• 1• 1• 1• 1• 1• 1• 1• 1• 1• 1• 1• 1• 1• 1• 1ο 1• 1• 1• 1ο 1ο 1ο 1ο 1ο 1ο 1ο 1ο 1ο 1ο 1ο 1ο 1ο 1ο 1ο 1ο 1ο 1ο 1ο 1ο 1ο 1ο 1ο 1ο 1ο 3ο 3ο 3ο 3ο 3ο 3ο 3ο 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,3 0,4 0,4 0,4 0,4 0,4 0,4 0,4 0,4 0,4 0,4 0,4 0,4 0,4 0,5 0,5 0,5 0,5 0,5 0,5 0,5 0,5 0,5 0,6 0,6 0,6 0,6 0,6 0,6 0,6 0,6 0,8 0,8 0,8 0,8 0,8 0,8 0,8 0,8 0,8 0,8 0,8 0,8 0,8 0,8 0,8 0,8 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,0 1,2 1,2 1,2 1,2 12000 9500 9500 8500 8500 8500 7500 7500 7500 6000 6000 6000 6000 5400 5400 5400 5400 5000 5000 5000 5000 5000 4750 4750 4750 4750 4750 4250 4250 4250 4250 3800 3800 3800 3800 3400 3400 3400 3400 3000 3000 3000 3000 2700 2700 2700 2700 2400 2400 2400 2400 2150 2150 2150 2150 1900 1900 1900 1900 1700 1700 1500 1500 1350 1350 1200 1200 90 100 125 140 150 160 180 200 224 250 280 315 355 400 450 500 560 630 Weight without bush 0,6 1,2 1,5 1,5 1,9 2,2 1,8 2,4 2,7 2,6 3,4 3,8 4,5 3,4 4,5 4,9 5,2 4,0 5,4 6,2 6,7 7,6 4,6 6,3 7,5 8,5 10,0 7,2 9,8 12,0 14,0 8,0 12,0 15,5 18,0 8,2 11,5 15,0 17,0 8,5 11,0 15,5 17,5 13,4 17,3 21,8 28,3 15,8 19,0 26,0 32,0 20,0 22,0 27,0 36,0 26,0 28,0 32,0 40,0 42,5 54,5 53,0 69,0 66,5 86,0 80,0 103,0 52 V- Belts and V- Belt Pulleys Chapter 11 Poly V- Pulleys Material: Fine grain cast- iron grade 220-260 Eccentricity of O/ D to bore DIN 7867 Groove side wobble tolerance: DIN 7867 Surface roughness: ISO 254 Balance quality grade: ISO 1940 - VDI 2060 Pulleys with dm (pcd) >125 mm are statically balanced to grade G 6,3. A residual unbalance of 2 g on the pulley dm (pcd) will be accepted. The residual unbalance is ≤100 g mm/ kg at 600 rev./ min. and 20 g mm/ kg at 3000 rev./ min. Dynamic G 6,3- G 2,5 balancing can be supplied to order. PROFIL J PROFIL L Grooves 4 8 12 16 20 Grooves 6 8 10 12 16 20 B(mm) 13,5 23 32,5 42 52 B(mm) 38,5 48 57 67 86 105 F(mm) 3,24 3,31 3,38 3,45 3,77 F(mm) 7,5 7,55 7,35 7,65 7,75 7,85 C. D. of grooves 2,34 C. D. of grooves 4,70 53 V- Belts and V- Belt Pulleys Chapter 11 Ordering code is composed as follow: PJ075 08T/1108 Poly- V Pulleys PJ 75 8 1108 T N DM Grooves Mat Part No 20 4 8 12 16 20 4 8 12 16 20 4 8 12 16 20 4 8 12 16 20 4 8 12 16 20 4 8 12 16 20 4 8 12 16 20 4 8 12 16 20 4 8 12 16 20 GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG PJ02004N PJ02008N PJ02012N PJ02016N PJ02020N PJ02504N PJ02508N PJ02512N PJ02516N PJ02520N PJ03004N PJ03008N PJ03012N PJ03016N PJ03020N PJ03504N PJ03508N PJ03512N PJ03516N PJ03520N PJ04004N PJ04008N PJ04012N PJ04016N PJ04020N PJ04504N PJ04508N PJ04512N PJ04516N PJ04520N PJ05004N PJ05008N PJ05012N PJ05016N PJ05020N PJ05604T PJ05608T PJ05612N PJ05616N PJ05620N PJ06004T PJ06008T PJ06012T PJ06016N PJ06020N 25 30 35 40 45 50 56 60 Taper Bush Type 1108 1108 1108 1108 1108 - Fig. 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 7 3 1 1 1 7 3 2 1 1 L K N J 22.5 - 32 - 41.5 - 51 - 61 - 22.5 - 32 - 41.5 - 51 - 61 - 22.5 - 32 - 41.5 - 51 - 61 - 22.5 - 32 - 41.5 - 51 - 61 - 22.5 - 32 - 41.5 - 51 - 61 - 22.5 - 32 - 41.5 - 51 - 61 - 22.5 - 32 - 41.5 - 51 - 61 - 23 9.5 50 23 - 41.5 - 51 - 61 - 23 9.5 50 23 - 23 9.5 - 45 51 - 61 - - d DM Grooves Mat. Part No 5 5 5 5 5 5 5 5 5 5 9.5 9.5 9.5 9.5 9.5 9.5 9.5 9.5 9.5 9.5 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 63 4 8 12 16 20 4 8 12 16 20 4 8 12 16 20 4 8 12 16 20 4 8 12 16 20 4 8 12 16 20 4 8 12 16 20 4 8 12 16 20 4 8 12 16 20 GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG PJ06304T PJ06308T PJ06312T PJ06316N PJ06320N PJ06704T PJ06708T PJ06712T PJ06716N PJ06720N PJ07104T PJ07108T PJ07112T PJ07116T PJ07120T PJ07504T PJ07508T PJ07512T PJ07516T PJ07520T PJ08004T PJ08008T PJ08012T PJ08016T PJ08020T PJ08504T PJ08508T PJ08512T PJ08516T PJ08520T PJ09004T PJ09008T PJ09012T PJ09016T PJ09020T PJ09504T PJ09508T PJ09512T PJ09516T PJ09520T PJ10004T PJ10008T PJ10012T PJ10016T PJ10020T 67 71 75 80 85 90 95 100 Poly- V section Pulley diameter Number of grooves Bush size With Bush Pre bored Taper Bush Type 1108 1108 1108 1108 1108 1108 1108 1108 1108 1215 1215 1108 1108 1210 1610 1615 1310 1310 1610 1610 1615 1310 1310 1610 1610 1615 1610 1610 1610 1610 1615 1610 1610 1610 1610 1615 1610 1610 1610 1610 1615 Fig. L K N J d 7 3 2 1 1 7 3 2 1 1 7 3 2 3 2 7 3 2 2 2 7 7 2 2 2 7 7 2 2 2 7 7 2 2 2 7 7 2 2 2 7 7 2 2 2 23 23 23 51 61 23 23 23 51 61 23 23 23 42 42 23 23 26 26 42 26 26 26 26 42 26 26 26 26 42 26 26 26 26 42 26 26 26 26 42 26 26 26 26 42 9.5 9.5 9.5 9.5 9.5 9.5 10 9.5 6.5 16 10 12.5 3 6.5 16 10 12.5 3 6.5 16 10 12.5 3 6.5 16 10 12.5 3 6.5 16 10 12.5 3 6.5 16 10 50 50 60 60 70 70 70 70 82 82 82 82 82 82 - 45 51 55 55 55 59 59 59 64 64 64 69 69 69 74 74 74 79 79 79 82 82 82 12 12 12 12 - 54 V- Belts and V- Belt Pulleys Chapter 11 Poly- V Pulleys DM Grooves Mat Part No 106 112 118 125 132 140 160 180 200 4 GG PJ10604T Taper Bush Fig. L Type 1610 7 N J d DM Grooves Mat. Part No 26 12.5 88 - - 224 K Taper Bush Fig. L Type K N J d 4 GG PJ22404T 2012 6 32 9.25 110 208 - GG PJ22408T 2012 6 32 4.5 110 208 - 88 - - 8 26 6.5 - 88 - 12 GG PJ22412T 2517 6 45 6.25 120 204 - 26 16 - 88 - 16 GG PJ22416T 2517 6 45 1.5 120 204 - 2 42 10 - 88 - 20 GG PJ22420T 2517 5 45 3.5 120 204 - 7 26 12.5 90 - - 4 GG PJ25004T 2012 9 32 9.25 110 234 - 8 GG PJ25008T 2012 9 32 4.5 110 234 - - 12 GG PJ25012T 2517 6 45 6.25 120 230 - 16 GG PJ25016T 2517 6 45 1.5 120 230 - 20 GG PJ25020T 2517 5 45 3.5 120 230 - 4 GG PJ28004T 2012 9 32 9.25 110 264 - GG PJ28008T 2012 9 32 4.5 110 264 - 8 GG PJ10608T 1610 7 26 12 GG PJ10612T 1610 2 16 GG PJ10616T 1610 2 20 GG PJ10620T 1615 4 GG PJ11204T 1610 3 8 GG PJ11208T 1610 7 26 3 12 GG PJ11212T 1610 2 26 6.5 90 - - 94 16 GG PJ11216T 1610 2 26 16 - 94 - 20 GG PJ11220T 1615 2 42 10 - 94 - 4 GG PJ11804T 1610 7 26 12.5 90 - - 8 GG PJ11808T 1610 7 26 3 12 GG PJ11812T 2012 2 32 0.5 90 - - - 98 - 12 GG PJ28012T 2517 9 45 6.25 120 260 - 16 GG PJ28016T 2517 9 45 1.5 120 260 - 20 GG PJ28020T 2517 10 45 3.5 120 260 - 4 GG PJ31504T 2012 9 32 9.25 110 299 - 90 109 - 8 GG PJ31508T 2012 9 32 4.5 110 299 - - 105 - 12 GG PJ31512T 2517 9 45 6.25 120 295 - 16 GG PJ31516T 2517 9 45 1.5 120 295 - 20 GG PJ31520T 2517 10 45 3.5 120 295 - 4 GG PJ35504T 2517 9 45 15.7 120 339 - GG PJ11816T 2012 2 32 10 - 98 - 20 GG PJ11820T 2012 2 32 20 - 98 - 4 GG PJ12504T 1610 8 26 12.5 90 109 - 8 GG PJ12508T 1610 8 26 12 GG PJ12512T 2012 2 32 0.5 16 GG PJ12516T 2012 2 32 10 - 105 - 20 GG PJ12520T 2517 2 45 - 105 - 7 280 8 16 3 250 4 GG PJ13204T 1610 8 26 12.5 90 116 - 315 355 8 GG PJ13208T 1610 8 26 90 116 - 8 GG PJ35508T 2517 9 45 12 GG PJ13212T 2012 2 32 0.5 - 112 - 12 GG PJ35512T 2517 9 45 6.25 120 335 - 16 GG PJ13216T 2012 2 32 10 - 112 - 16 GG PJ35516T 3020 9 52 5 146 335 - 20 GG PJ13220T 2517 2 45 - 112 - 20 GG PJ35520T 3020 10 52 - 146 335 - 4 GG PJ40004T 2517 9 45 15.75 120 380 - 3 7 4 GG PJ14004T 1610 8 26 12.5 90 124 - 8 GG PJ14008T 1610 8 26 3 90 124 - 400 11 120 339 - 8 GG PJ40008T 2517 9 45 GG PJ40012T 2517 9 45 6.25 120 380 - 11 120 380 - 12 GG PJ14012T 2517 7 45 12.5 120 - - 12 16 GG PJ14016T 2517 7 45 3 120 - - 16 GG PJ40016T 3020 9 52 5 146 380 - 20 GG PJ14020T 2517 2 45 7 - 124 - 20 GG PJ40020T 3020 10 52 - 146 380 - 4 GG PJ16004T 2012 8 32 18.5 110 144 - 8 GG PJ16008T 2012 8 32 12 GG PJ16012T 2517 8 45 12.5 120 140 - 16 GG PJ16016T 2517 8 45 3 120 140 - 20 GG PJ16020T 2517 2 45 7 4 GG PJ18004T 2012 6 32 9.25 110 164 - 8 GG PJ18008T 2012 6 32 4.5 110 164 - 12 GG PJ18012T 2517 6 45 6.25 120 160 - 16 GG PJ18016T 2517 6 45 1.5 120 160 - 20 GG PJ18020T 2517 5 45 3.5 120 160 - 4 GG PJ20004T 2012 6 32 9.25 110 185 - 8 GG PJ20008T 2012 6 32 4.5 110 185 - 12 GG PJ20012T 2517 6 45 6.25 120 180 - 16 GG PJ20016T 2517 6 45 1.5 120 180 - 20 GG PJ20020T 2517 5 45 3.5 120 180 - 9 110 144 - - 140 - 55 V- Belts and V- Belt Pulleys Chapter 11 Poly- V Pulleys Ordering code is composed as follow: PL150 10T/2517 PL 150 10 2517 T DM Grooves Mat Part No 75 6 8 10 12 6 8 10 12 6 8 10 12 16 6 8 10 12 16 6 8 10 12 16 6 8 10 12 16 6 8 10 12 16 6 8 10 12 16 6 8 10 12 16 20 GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG PL07506T PL07508T PL07510T PL07512T PL08006T PL08008T PL08010T PL08012T PL08506T PL08508T PL08510T PL08512T PL08516T PL09006T PL09008T PL09010T PL09012T PL09016T PL09506T PL09508T PL09510T PL09512T PL09516T PL10006T PL10008T PL10010T PL10012T PL10016T PL10606T PL10608T PL10610T PL10612T PL10616T PL11206T PL11208T PL11210T PL11212T PL11216T PL11806T PL11808T PL11810T PL11812T PL11816T PL11820T 80 85 90 95 100 106 112 118 Taper Bush Type 1210 1210 1215 1215 1210 1210 1215 1215 1210 1210 1215 1215 1215 1610 1610 1615 1615 1615 1610 1610 1615 1615 1615 1610 1610 2012 2012 2012 1610 1610 2012 2012 2012 1610 1610 2012 2012 2012 2012 2012 2517 2517 2517 2517 Fig. L K 2 2 2 2 2 2 2 2 2 2 2 2 4 2 2 2 2 4 2 2 2 2 4 2 2 2 2 4 2 2 2 2 4 2 2 2 2 4 2 2 4 4 4 4 26 26 42 42 26 26 42 42 26 26 42 42 42 26 26 42 42 42 26 26 42 42 42 26 26 32 32 32 26 26 32 32 32 26 26 32 32 32 32 32 45 45 45 45 12.5 22 15 25 12.5 22 15 25 12.5 22 15 25 22 12.5 22 15 25 22 12.5 22 15 25 22 12.5 22 25 35 27 12.5 22 25 35 27 12.5 22 25 35 27 6.5 16 6 11 20.5 30 N J DM Grooves Mat. Part No - 125 6 8 10 12 16 20 6 8 10 12 16 20 6 8 10 12 16 20 6 8 10 12 16 20 6 8 10 12 16 20 6 8 10 12 16 20 6 8 10 12 16 20 6 8 10 12 16 20 GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG PL12506T PL12508T PL12510T PL12512T PL12516T PL12520T PL13206T PL13208T PL13210T PL13212T PL13216T PL13220T PL14006T PL14008T PL14010T PL14012T PL14016T PL14020T PL15006T PL15008T PL15010T PL15012T PL15016T PL15020T PL16006T PL16008T PL16010T PL16012T PL16016T PL16020T PL17006T PL17008T PL17010T PL17012T PL17016T PL17020T PL18006T PL18008T PL18010T PL18012T PL18016T PL18020T PL19006T PL19008T PL19010T PL19012T PL19016T PL19020T 56 56 56 56 56 56 56 56 61 61 61 61 61 66 66 66 66 66 71 71 71 71 71 76 76 79 79 79 82 82 82 82 82 88 88 88 88 88 94 94 97 97 97 97 132 140 150 160 170 180 190 Poly- V section Pulley diameter Number of grooves Bush size With Bush Taper Bush Type 2012 2012 2517 2517 2517 2517 2012 2012 2517 2517 2517 2517 2517 2517 2517 2517 2517 3020 2517 2517 2517 2517 2517 3020 2517 2517 2517 2517 3020 3020 2517 2517 2517 2517 3020 3020 2517 2517 2517 2517 3020 3020 2517 2517 2517 2517 3020 3020 Fig. L K N J 2 2 4 4 4 4 2 2 4 4 4 4 7 2 4 4 4 4 7 2 4 4 4 4 7 2 4 4 4 4 8 2 4 4 4 4 6 5 5 5 4 4 6 5 5 5 5 5 32 32 45 45 45 45 32 32 45 45 45 45 45 45 45 45 45 52 45 45 45 45 45 52 45 45 45 45 52 52 45 45 45 45 52 52 45 45 45 45 52 52 45 45 45 45 52 52 6.5 16 6 11 20.5 30 6.5 16 6 11 20.5 30 6.5 3 6 11 20.5 26.5 6.5 3 6 11 20.5 26.5 6.5 3 6 11 17 26.5 6.5 3 6 11 17 26.5 3.25 1.5 6 11 17 26.5 3.25 1.5 6 11 17 26.5 120 120 120 120 120 120 120 120 120 120 120 120 146 146 101 101 101 101 101 101 108 108 108 108 108 108 116 116 116 116 116 126 126 126 126 126 136 136 136 136 136 146 146 146 146 146 146 156 156 156 156 156 156 166 166 166 166 166 166 56 V- Belts and V- Belt Pulleys Chapter 11 Poly- V Pulleys DM Grooves Mat Part No 200 6 8 10 12 16 20 6 8 10 12 16 20 6 8 10 12 16 20 6 8 10 12 16 20 6 8 10 12 16 20 6 8 10 12 16 20 6 8 10 12 16 20 6 8 10 12 16 20 GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG PL20006T PL20008T PL20010T PL20012T PL20016T PL20020T PL21206T PL21208T PL21210T PL21212T PL21216T PL21220T PL22406T PL22408T PL22410T PL22412T PL22416T PL22420T PL23606T PL23608T PL23610T PL23612T PL23616T PL23620T PL25006T PL25008T PL25010T PL25012T PL25016T PL25020T PL28006T PL28008T PL28010T PL28012T PL28016T PL28020T PL31506T PL31508T PL31510T PL31512T PL31516T PL31520T PL35506T PL35508T PL35510T PL35512T PL35516T PL35520T 212 224 236 250 280 315 355 Taper Bush Type 2517 2517 3020 3020 3020 3535 2517 2517 3020 3020 3020 3535 2517 2517 3020 3020 3020 3535 2517 2517 3020 3020 3020 3535 2517 2517 3020 3020 3020 3535 2517 2517 3020 3020 3020 3535 2517 3020 3535 3535 3535 4040 3020 3020 3535 3535 3535 4040 Fig. L K N J DM Grooves Mat Part No 6 5 5 5 5 4 6 5 5 5 5 4 6 5 5 5 5 5 6 5 5 5 5 5 9 5 5 5 5 5 6 6 5 5 6 5 9 9 6 6 6 5 9 9 9 9 9 5 45 45 52 52 52 89 45 45 52 52 52 89 45 45 52 52 52 89 45 45 52 52 52 89 45 45 52 52 52 89 45 52 52 52 89 89 45 52 89 89 89 102 52 52 89 89 89 102 3.25 1.5 2.5 7.5 17 8 3.25 1.5 2.5 7.5 17 8 3.25 1.5 2.5 7.5 17 8 3.25 1.5 2.5 7.5 17 8 3.25 1.5 2.5 7.5 17 8 3.25 2 2.5 7.5 1.5 8 3.25 2 16 11 1.5 1.5 6.75 2 16 11 1.5 1.5 120 120 146 146 146 120 120 146 146 146 120 120 146 146 146 120 120 146 146 146 178 120 120 146 146 146 178 120 146 146 146 178 178 120 146 178 178 178 215 146 146 178 178 178 215 176 176 176 176 176 176 188 188 188 188 188 188 202 202 202 202 202 202 214 214 214 214 214 214 228 228 228 228 228 228 256 256 256 256 256 256 285 285 285 285 285 285 325 325 325 325 325 325 400 6 8 10 12 16 20 6 8 10 12 16 20 6 8 10 12 16 20 6 8 10 12 16 20 6 8 10 12 16 20 GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG GG PL40006T PL40008T PL40010T PL40012T PL40016T PL40020T PL45006T PL45008T PL45010T PL45012T PL45016T PL45020T PL50006T PL50008T PL50010T PL50012T PL50016T PL50020T PL63006T PL63008T PL63010T PL63012T PL63016T PL63020T PL80006T PL80008T PL80010T PL80012T PL80016T PL80020T 450 500 630 800 Taper Bush Type 3020 3020 3535 3535 3535 4040 3020 3020 3535 3535 3020 4040 3020 3020 3535 3535 3535 5050 3020 3020 3535 3535 4040 5050 3535 3535 4040 4040 5050 5050 Fig. L K N J 9 9 9 9 9 10 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 52 52 89 89 89 102 52 52 89 89 89 102 52 52 89 89 89 127 52 52 89 89 102 127 89 89 102 102 127 127 6.75 2 16 11 1.5 1.5 6.75 2 16 11 1.5 1.5 6.75 2 16 11 1.5 11 6.75 2 16 11 1.5 11 25.2 20.5 22.5 17.5 20.5 11 146 146 178 178 178 215 146 146 178 178 178 215 146 146 178 178 178 267 146 146 178 178 215 267 178 178 215 215 267 267 370 370 370 370 370 370 420 420 420 420 420 420 470 470 470 470 470 470 600 600 600 600 600 600 770 770 770 770 770 770 57 V- Belts and V- Belt Pulleys Chapter 11 Taper Bushes / Metric 58 V- Belts and V- Belt Pulleys Chapter 11 Taper Bushes / Imperial 59 Innledning Bibel rev 3 (vår 2012) Important addresses and phone numbers NORWAY Bergen Postal address: Postboks 144 Ulset N-5873 BERGEN Lönne Scandinavia AS Visit address Liamyrane12, N-5132 NYBORG Phones/ Faxes ph: +47 55 39 10 00 fax: +47 55 39 11 00 24- h.service: +47 918 33 073 Oslo: Postal and visit address: Lönne Scandinavia AS Frysjaveien 40 N-0884 OSLO Phones/ Faxes ph: +47 22 02 10 30 fax: +47 22 02 10 50 Ålesund: Postal address: Lönne Scandinavia AS Visit address: Phones/ Faxes Po.Box 7892 Spjelkavikveien 9 ph: +47 70 15 39 00 6022 Ålesund N-6011 ÅLESUND fax: +47 70 15 39 01 Helsingborg Postal and visit address: Lönne Scandinavia AB Kastellgatan 5 S-254 66 HELSINGBORG Phones/ Faxes ph +46(0)42 38 03 00 fax: +46(0)42 38 03 09 24- h. service: +46 (0) 70 885 5431 Stockholm: Lönne Scandinavia AB Phones/ Faxes Postal and visit address: Lovisagatan 4 S-115 23 STOCKHOLM ph: +46-8 662 62 85 fax: +46-8 545 697 20 Helsinki Lönne Scandinavia OY Phones/ Faxes Postal and visit address: Hernepellontie 11Service phone: +358 50 570 4070 FI-00710 HELSINKI ph: +358(0)9342 4300 fax: +358(0)9342 43099 Service phone: +358 50 570 4070 SWEDEN FINLAND DENMARK Vejle Lönne Scandinavia AS Postal and visit address: Bugattivej 5G .............................................DK-7100 VEJLE Phones/ Faxes ph: +45 76 40 87 00 fax: +45 76 40 87 01 24- h. service: +45 24 45 74 03 Lönne Service Main Office Solgaard Skog 7, P.O. Box 460, N-1502 MOSS, Norway. www Telephone +47 69 24 40 00 Fax +47 69 24 07 45 24- h. service +47 924 32 085 Price Policy Prices occur in special lists on requirement in specified currency, ex warehouse exclusive packaging. The sales tax (value added tax) is not included in the prices. It shall be debited separately at the respective rate according to the applicable legal regulations. Environmental Protection - Information Requirement Terms of Sales and delivery are specified on our web site; www.lonne.com Electric and electronic products, so- called EE products may contain toxins which can damage our health and the environment. Therefore, all importers and producers of EE products are obliged to take responsibility for their products until they have been scrapped and recycled. You may return any cast- off Lönne products to a Lönne Warehouse. Lönne is obliged to fulfil the authorities’ requirements regarding an environmentally sound handling of EEwaste in accordance with the EE regulations. Lönne Scandinavia AS reserves the prohibition to publish pages or whole parts of this catalogue without athorization. General Terms of Sales and Delivery Export and Import Regulations regarding Lönne Product Range of Drives and Controls will be subject to the Export Import Regulations actual in the area of delivery. We hereby reserve the right to change the content of data in this catalogue at any time without notice. Furthermore, our company shall not be held responsible for neither possible discrepancies in catalogue content nor any damage caused by wrong use of products or information. 6 61 Products | Solutions | Services Lönne Main Catalogue Chapters: Chapter 1 Electric Motors Chapter 2 Generators Chapter 3 ECOiPM PM Motors Chapter 4 Frequency Inverters Chapter 5 Servo Controls Chapter 6 Machine Controls Chapter 7 Worm Gear Boxes Chapter 8 Helical Gear Boxes Chapter 9 Torque Arm Speed Reducers Chapter 10 Planetary Gear Boxes Chapter 11 V-belt and V-belt Pulleys Chapter 12 Timing Belt and Timing Belt Pulleys Chapter 13 Chains and Sprockets Chapter 14Couplings Chapter 15 Clamping Elements Chapter 16 Disk Brakes Chapter 17 Bearings Chapter 18Vibrators Lönne Lönne Scandinavia AS was founded in 1949 in Bergen, Norway. Present board member Mr Terje Lönne entered as second generation, and started the expansion into the Nordic market. Lönne has specialized within electric motors, generators, frequency inverters, gearboxes, transmissions and bearings. Lönne reference list covers a wide range of customers within on shore, off shore, maritime and marine industries. Step by step the company has grown to become a leading, Nordic supplier within drive technology. Lönne one stop shop concept is a strong force for customers whom operate the total value chain of drive technology components. Lönne is today widely recognized both as a supplier of high quality components and engineered solutions. Lönne head quarter is located in Bergen, Norway, with subsidiaries in Denmark, Finland and Sweden. The central warehouse, workshop and testing department in Helsingborg provides quick delivery service overnight, to the Nordic market. Smaller express warehouses and workshops are also located in Bergen and Helsinki. See map on the back page for the total Lönne Group. Lönne Service is a separate part of the Lönne Group. With a total of six workshops in Norway, Lönne Service is specializing in services and repairing of electric motors and generators, both towards on shore and off shore markets. Lönne Service is ranked to have one of the market's largest and most updated machine parks, operated by highly skilled personnel. Lönne people take pride in every job done, with a high level of professionalism, and really care to ”keep your machinery running!” Lönne Quality Management System Standards is certified for ISO 9001:2008. For further information, please have a look at our website or feel free to call us! Norway Sweden Denmark Finland Lönne Scandinavia AS Liamyrane 12, Bergen N-5132 Nyborg Bergen Tel: +47 55 39 10 00 Fax: +47 55 39 11 00 Local mail: info.norway@lonne.com 24-h. service: +47 91 83 30 73 Lönne Scandinavia AB Kastellgatan 5 S-254 66 Helsingborg Tel: +46 (0) 42 38 03 00 Fax: +46 (0) 42 38 03 09 Local mai: info.sweden@lonne.com 24-h. service: +46 (0) 70 88 55 43 1 Lönne Scandinavia AS Bugattivej 5G DK-7100 Vejle Tel: +45 (0) 76 40 87 00 Fax: +45 (0) 76 40 87 01 Local mail: info.denmark@lonne.com 24-h. service: +45 (0) 24 45 74 03 Lönne Scandinavia OY Hernepellontie FI-00560 Helsinki Tel: +358 (0) 9 342 4300 Fax: +358 (0) 9 3424 3099 Local mai: info.finland@lonne.com Head Office