Untitled

Page 2 of 10
Report Ref. No.: SH09110603-001
Amendment 5: 25 December, 2012
Manufacturer .................................... :
Same as applicant
Rating(s) .......................................... :
230-240V~, 50Hz, Max. Cutting depth: 50mm,
Class II, Saw blade diameter: Ø210mm,
Saw blade bore diameter: Ø25,4mm(Ø30mm)
J1X-KZ5-210L, J1X-KZ5-210P, J1X-KZ2-210HL, J1X-KZ2-210HP,
PMS210, PMSL210M, J1X-KZ5-210LJ, J1X-KZ5-210PJ, J1X-KZ2210HLJ, J1X-KZ2-210HPJ, J1X-KZ17-210L, J1X-KZ17-210LJ:
-1
1400W, n0: 5000min
J1X-KZ8-210L, J1X-KZ8-210P, J1X-KZ8-210LJ, J1X-KZ8-210PJ:
-1
1400W (S1)/ 1600W (S6: 40%), n0: 5000min
FURY3-B, FURY3B2102, RAGE3-B, RAGE3B2102,
-1
RAGE3B2102EU: 1100W, n0: 4000min
Remarks ........................................... :
1 J1X-KZ5-210L is identical with J1X-KZ5-210P except that J1XKZ5-210L is provided with aluminium base while J1X-KZ5-210P is
provided with plastic base.
2. J1X-KZ2-210HL is identical with J1X-KZ2-210HP except that
J1X-KZ2-210HL is provided with aluminium base while J1X-KZ2210HP is provided with plastic base.
3. J1X-KZ8-210L is identical with J1X-KZ8-210P except that J1XKZ8-210L is provided with aluminium base while J1X-KZ8-210P is
provided with plastic base.
4. J1X-KZ5-210L, J1X-KZ2-210HL and J1X-KZ8-210L are same
except that their guard construction and shape of base are
different each other.
5. J1X-KZ5-210LJ, J1X-KZ5-210PJ,J1X-KZ2-210HPJ, J1X-KZ2210HLJ, J1X-KZ8-210LJ, J1X-KZ8-210PJ have the laser module
system while J1X-KZ5-210L, J1X-KZ5-210P, J1X-KZ2-210HP,
J1X-KZ2-210HL, J1X-KZ8-210L, J1X-KZ8-210P have not laser
module system.
6. PMS210 is identical with J1X-KZ5-210P except for model name.
7. PMSL210M is identical with J1X-KZ5-210LJ except for model
name.
8. FURY3-B is identical with J1X-KZ5-210LJ except for motor,
rating and model name.
9. FURY3-B, FURY3B2102, RAGE3-B, RAGE3B2102 and
RAGE3B2102EU are identical to each other except for model
name.
10. J1X-KZ17-210L is identical with J1X-KZ5-210L except base.
11. J1X-KZ17-210LJ is identical with J1X-KZ17-210L except that
J1X-KZ17-210LJ has laser module system while J1X-KZ17-210L
has no laser module system.
TTRF_EN61029_1A’
Page 3 of 10
Report Ref. No.: SH09110603-001
Amendment 5: 25 December, 2012
Particulars: test item vs. test requirements
Operating condition ................................................:
Continuous
Supply connection ..................................................:
Type X
Mass of appliance .................................................:
5,62kg (max.)
Electrical safety class .............................................:
Class II
IP number ..............................................................:
IP20
Test case verdicts
Test case does not apply to the test object ............. :
N/A
Test item does meet the requirement ..................... :
P(ass)
Test item does not meet the requirement ............... :
F(ail)
Testing
Date of receipt of test item ...................................... :
4 December, 2012
Date(s) of performance of test ................................ :
4 December, 2012 – 25 December, 2012
General remarks
This test report shall not be reproduced except in full without the written approval of the testing laboratory.
The test results presented in this report relate only to the item tested.
"(see remark #)" refers to a remark appended to the report.
"(see appended table)" refers to a table appended to the report.
Throughout this report a comma is used as the decimal separator.
Determination of the test result includes consideration of measurement uncertainty from the test equipment
and methods.
General product information:
The product covered in this report is a transportable electric Mitre Saw for cutting wood. The Mitre Saw is
provided with a laser to indicate a cutting line (for models J1X-KZ5-210LJ, J1X-KZ5-210PJ, J1X-KZ2210HLJ, J1X-KZ2-210HPJ, J1X-KZ8-210LJ, J1X-KZ8-210PJ, PMSL210M, J1X-KZ17-210LJ).
Factory’s name: Yongkang Zhengda Industrial Co., Ltd.
Factory’s address: 558 Great Wall East RD, Hardware-Tech. Industrial Zone, Yongkang, Zhejiang, 321300,
P. R. China.
This report based on SH09010267-001 dated on 9 April, 2009, Amendment-1 dated on 16 June, 2009,
Amendment-2 dated on 26 August, 2009, SH09110603-001 dated on 22 December, 2009, Amendment-1
dated on 30 June, 2010, Amendment-2 dated on 22 February, 2012, Amendment-3 dated on 22 May, 2012,
Amendment-4 dated on 31 July, 2012 and SH09110603-002 dated on 22 December, 2009.
General conclusion:
The appliance is found to comply with the standard's requirements.
This report shall be used in conjunction with SH09010267-001 with A1 and A2, SH09110603-001 with A1
A2, A3 and A4, and SH09110603-002.
TTRF_EN61029_1A’
Page 4 of 10
Report Ref. No.: SH09110603-001
Amendment 5: 25 December, 2012
Summary of testing:
All the tests in this report were performed with model J1X-KZ17-210LJ, which cover test requirements of all
other models.
The submitted samples were tested according to standards above and found to comply with the standards’
requirements, and annex I of 2006/42/EC.
Amendment 5 of SH09110603-001:
This report based on SH09110603-001: 2009-12-22, A1: 2010-06-30, A2: 2012-02-22, A3: 2012-05-22 and
A4: 2012-07-31, with additional changes as following:
1. Add two new models J1X-KZ17-210L and J1X-KZ17-210LJ.
2. Add some alternative used power cords.
Clauses concerned:
7, 18 and 22 of EN 61029-1:2009+A11:2010.
7, 18 and 22 of EN 61029-2-9:2009.
TTRF_EN61029_1A’
Page 5 of 10
Report Ref. No.: SH09110603-001
Amendment 5: 25 December, 2012
Copy of marking plate (Representative)
J1X-KZ17-210L Gehrungskappsäge
230-240V~ 50Hz 1400W n0: 5000/min
Durchmesser Von Sägeblatt: Ø210mm
Bohrungsdurchmesser: Ø25,4mm(Ø30mm)
BJ 2012
Zhengyang Industry & Investment Co., Ltd.
558 Great Wall East RD, Hardware-Tech Industrial Zone,
Yongkang, Zhejiang 321300, P. R. China
Seriennummer: XXXXXX
Bevollmächtigte Person in EU: (Name, Adresse)
.
TTRF_EN61029_1A’
Page 6 of 10
Report Ref. No.: SH09110603-001
Amendment 5: 25 December, 2012
EN 61 029-1
Clause
Requirement + Test
Result - Remark
7
MARKING
7.1
Rated voltage(s) (V) .............................................. :
230-240V
P
Nature of supply
~
P
Rated frequency (Hz)............................................. :
50Hz
P
Rated Input (W or kW) .......................................... :
See copy of marking plate
P
Rated current (A) if greater than 10A .................... :
Verdict
N/A
Business name and address of manufacture and,
where applicable, his authorised representative.
Any address shall be sufficient to ensure contact . :
See copy of marking plate
P
Designation of the tool ............................................ :
See copy of marking plate
P
Designation of series or type .................................. :
See copy of marking plate
P
The year of manufacture ........................................ :
See copy of marking plate
P
Rated operating/resting time, if applicable.
N/A
Symbol for Class II
Symbol for protection against moisture if greater
than IP20
P
IP20
N/A
Tool for star-delta connection clearly marked with the
two voltages
N/A
Rated input or current is the total maximum that can
be on the circuit at the same time
N/A
In case of alternative components, the rated input is
corresponding to the highest load
N/A
Additional markings (e.g. motor markings) are
allowed, provided that they do not give rise to
misunderstanding
P
18
STABILITY AND MECHANICAL HAZARDS
18.1
Protection against injury by parts moving in normal
use
P
Adequate mechanical strength of protective
enclosures and guards
P
Fixed guard shall be used when frequent access is
not required and removal of this type of guard shall
only be possible with the aid of a tool.
P
Where more frequent access is required, movable
or removable guards shall be provided to enclose
the dangerous parts of the tool.
P
For fixed guards that are to be removed at the place Fixed guard will not be
of use as part of the routine maintenance
removed during routine
procedure, as described in the instruction manual, maintenance.
the fastenings shall remain attached to the guards
or to the tool. (A11:2010)
TTRF_EN61029_1A’
N/A
Page 7 of 10
Report Ref. No.: SH09110603-001
Amendment 5: 25 December, 2012
EN 61 029-1
Clause
Requirement + Test
Result - Remark
Verdict
- used as protection of working element
P
- during use and adjustment
P
All working elements are secured so that they
cannot create dangers
P
Compliance with tests of Cl. 19
P
Not possible to touch moving parts through dust
collection openings
P
Adequate stability
P
Tilting test through an angle of 10° appliance does
not overturn
P
18.3
Tools have adequate stability under the most
onerous condition
P
18.4
No sharp edges, burrs, flashes and the like
P
22
COMPONENTS
22.1
Components comply with relevant EN standards
18.2
(see appended table)
Components used in accordance with their
markings
22.2
P
P
Capacitors in series with a motor winding marked
with rated voltage and rated capacitance
N/A
Measured voltage across capacitor with tool
operating at 1,1 times rated voltage under minimum
load not exceeding 1,1 times rated voltage of
capacitor
N/A
Adequate breaking capacity of mains switches
Certified switch
P
Mains switches have a contact separation of at
least 3 mm
P
Mains switches rated for frequent operation
P
Switch operated 50 times with motor stalled
P
Mains switches marked with individual ratings
tested in accordance with EN 61058-1
P
22.3
Mains switches not fitted in the flexible cable or cord
P
22.4
Overload protection devices of the non-selfresetting type
22.5
Plugs and appliance inlets for safety extra-low
voltage circuits or for frequencies other than 50 Hz
of 60 Hz not interchangeable with plugs, connectors
and appliance inlet complying with IEC 60083 or EN
60320-1
N/A
22.6
Capacitors not connected between contacts of
thermal cut-outs
N/A
TTRF_EN61029_1A’
No overload protection device
N/A
Page 8 of 10
Report Ref. No.: SH09110603-001
Amendment 5: 25 December, 2012
EN 61 029-1
Clause
Requirement + Test
22.7
Components for basic radio and television
interference suppression are not incorporated in
plugs
22.8
Inductors for radio and television interference
suppression inserted in the earthing circuit
N/A
Inductor test
N/A
22.9
Appliance couplers comply with EN 60320-1
N/A
22.1
TABLE: components
P
object/part
manufacturer/
No.
trademark
Result - Remark
type/model
See Constructional Data Form (CDF) for the detail.
TTRF_EN61029_1A’
technical data
Verdict
P
standard
mark(s) of
conformity
Page 9 of 10
Report Ref. No.: SH09110603-001
Amendment 5: 25 December, 2012
EN 61029-2-9
Clause
Requirement + Test
7
MARKING AND INFORMATION FOR USE
7.1
Mitre saw shall be marked with:
7.6
Result - Remark
Verdict
- maximum and minimum saw blade diameter;
See copy of marking plate
P
- rated no-load speed;
Ditto
P
- indication of direction of rotation of the saw blade;
Ditto
P
- saw blade bore diameter.
Ditto
P
The direction of rotation of the blade shall be
indicated on a fixed part of the mitre saw in the
vicinity of the spindle axis by an arrow raised or
sunk, which is visible when changing the blade, or
by any other means not less visible and indelible.
By a raised arrow on fixed
guard
P
Rubbing test
P
7.10
Regulation devices marked with ........................... :
No regulation devices
7.11
Switches so marked or placed as to indicate clearly
which part of the tool they control
7.13
The substance of the following instructions shall also be given:
N/A
P
c) Safety precautions
P
e) safe operation
P
Special safety instruction for mitre saws
P
The following information shall also be given:
18
18.3
-the range of outside diameter ,bore diameter and
thickness of blade which may be used
P
-max. depth of cut
P
-if compound bevelling is possible, the safe method of Only one bevel cutting
operation
P
STABILITY AND MECHANICAL HAZARDS
In any working position the machine shall have sufficient stability
Compliance is check by the following test, without the tool being fixed to the bench
- With the tool in its position at 90º to the table and
0º mitre angle, a beech work piece, having
maximum dimensions for the machine not being
fixed to a bench, if such dimensions are provided by
the manufacturer, is clamped to the table against the
fence using the device supplied with the tool, with
one end aligned to the cutting slot. The machine
shall stay in position without any intervention from
the operator. The test is repeated with the work
piece on the opposite side of the cutting slot.
TTRF_EN61029_1A’
P
Page 10 of 10
Report Ref. No.: SH09110603-001
Amendment 5: 25 December, 2012
EN 61029-2-9
Clause
Requirement + Test
- Without any work piece, the saw unit is moved
down to its lowest position, and then the handle is
released, The machine shall not turn over and shall
not be displaced over a distance of more than
100mm.
22
Result - Remark
Verdict
P
COMPONENTS
The clause of part 1 is applicable.
TTRF_EN61029_1A’
P