DERO DECKER™

D E R O D E C K E R™
The Next Level of Parking
Patent #8,950,592
The Dero Decker™ takes bike parking to the next level – literally. By stacking
bikes on a two-tiered system, capacity doubles. Unlike other two-tier systems
our lift-assist top trays slide down inches from the ground, thus requiring only
minimal lifting of the bike into the tray. The Dero Decker™ has a front wheel
safety locking lever and tray dampers to provide safe lowering of upper trays.
The vertical load trays also reduce the required aisle space, giving the Dero
Decker™ the smallest footprint on the market.
© 2016 Dero
D E R O D E C K E R™
•
•
•
•
•
•
Sturdy red handle grips
Lift-assist trays
Dampers for gentle lowering of trays
Hinged levers hold bikes firmly in place
U-lock compatible
Smallest footprint
FINISH OPTIONS
Galvanized
Stainless
Powder Coat
White
Black
Light Gray
RAL 7042
Deep Red
RAL 3003
Yellow
RAL 1023
CNH Bright Yellow
Orange
RAL 2004
Blue
RAL 5005
Sky Blue
RAL 5015
Hunter Green
RAL 6005
Light Green
RAL 6018
Green
RAL 6016
Sepia Brown
RAL 8014
Bronze
Silver
9007
Dark Purple
Flat Black
Wine Red
RAL 3005
Beige
RAL 1001
Iron Gray
7011
Thermoplastic
Black
www.dero.com
|
Green
Red
Blue
1-888-337-6729
© 2016 Dero
Gray
Brown
DERO DECKER™
Submittal Sheet
CAPACITY
Modular 2-Tiered System in sections of 4, 8, 12, 16 or 24.
One bike per upper tray, one bike per lower tray.
MATERIALS
Uprights: 4” 12g square tube
Upright base: 1/4” plate
Crossbar: 4” 7g square tube
Cantilevers: 2” x 4” 11g tube
Cantilever base: 1/4” plate
Trays: 1/8” plate, ½” round bar
FINISHES
Galvanized
An after fabrication hot dipped galvanized finish is our
standard option.
Powder Coat
Our powder coat finish assures a high level of adhesion and
durability by following these steps:
1. Sandblast
2. Epoxy primer electrostatically applied
3. Final thick TGIC polyester powder coat
Stainless
Stainless Steel: 304 grade stainless steel material finished in
either a high polished shine or a satin finish.
MOUNT
OPTIONS
Surface
Each upright has two ¼” plate feet that accept 3/8” wedge
anchors.
SETBACKS
See following page
U-lock compatible
www.dero.com
© 2016 Dero
|
1-888-337-6729
DERO DECKER™
Installation Instructions – Setbacks for Configurations
24”
24”
8”
26”
26”
24”
DD-SS-4
4 Bikes
DD-DS-8
8 Bikes
108”
108”
17”
24”
8.5”
60”
48”
60”
62”
80”
17”
8”
24”
48”
60”
8.5”
60”
62”
80”
24”
DD-SS-8
8 Bikes
DD-DS-16
16 Bikes
108”
108”
17”
24”
8.5”
48”
60”
94”
62”
80”
17”
24”
8”
48”
60”
8.5”
94”
62”
80”
24”
DD-SS-12
12 Bikes
DD-DS-24
24 Bikes
108”
108”
17”
8.5”
48”
60”
62”
80”
17”
www.dero.com
© 2016 Dero
|
8.5”
48”
60”
62”
80”
1-888-337-6729
DERO DECKER™
Installation Instructions – Single Sided
TOOLS NEEDED
Hammer drill
Masonry bit, 3/8”
Hammer
Socket wrench
Sockets, 3/8”, 15/16”
Socket extension, 4”
Wrench, 15/16”
Tape measure
Carpenter’s square
Chalk line
Marker
Level
1
2
Refer to setback diagrams before installation to
ensure sufficient space. Installation surface must
be level. If surface is not level, contact Dero
representative for workable solution.
Place both Uprights in position and place the
CROSS BEAM on top of the UPRIGHTS. Secure
the CROSS BEAM to each UPRIGHT with at
least two 5/8 x 5.5” bolts placed diagonally
from each other.
3
4
After checking that the unit is square and that the
minimum setbacks have been achieved, anchor
the UPRIGHTS to the floor with 5 wedge anchors
each.
Starting at one end of the CROSS BEAM
and working your way to the other, place a
CANTILEVER ASSEMBLY and secure it with four
5/8 x 5.5” bolts, lock washers, and nuts. Check
to make sure the CANTILEVER ASSEMBLY is at
90º to the CROSS BEAM. After tightening the
fourth bolt, retighten all four bolts.
www.dero.com
© 2016 Dero
|
1-888-337-6729
DERO DECKER™
Installation Instructions – Single Sided
5
6
Place and secure the rest of the CANTILEVER
ASSEMBLIES with alternating Up and Down
CANTILEVER ASSEMBLIES. If a CANTILEVER
ASSEMBLY is above an UPRIGHT, they will share
hardware.
Place the LOWER TRAYS in position on the
ground with alternating UP and DOWN LOWER
TRAYS. The LOWER TRAYS should be in
between the CANTILEVER ASSEMBLIES The
front edge of the UP and DOWN LOWER
TRAYS are coincident and 62” from the back
edge of the UPRIGHT base flange. Secure
the LOWER TRAYS to the ground with wedge
anchors.
34”
When placing multiple units in a row, the
space between uprights of separate units
should be 34” center to center.
www.dero.com
© 2016 Dero
|
1-888-337-6729
DERO DECKER™
Installation Instructions – Double Sided
1
2
Refer to setback diagrams before installation to
ensure sufficient space.
Place both UPRIGHTS in position and place
the CROSS BEAM on top of the UPRIGHTS.
Secure the CROSS BEAM to each UPRIGHT
with at least two 5/8 x 5.5” bolts placed
diagonally from each other.
3
4
After checking that the unit is square and that the
minimum setbacks have been achieved, anchor
the UPRIGHTS to the floor with 6 wedge anchors
each.
Remove the CROSS BEAM and place DOWN
CANTILEVER ASSEMBLIES on top of the
UPRIGHTS. Place the CROSS BEAM on top of
the UPRIGHTS and CANTILEVER ASSEMBLIES
and secure the CROSS BEAM to each
UPRIGHT with at least two 5/8 x 5.5” bolts
placed diagonally from each other.
5
While supporting the DOWN CANTILEVER
ASSEMBLY, remove the 5/8 x 5.5” bolts and
place an UP CANTILEVER ASSEMBLY and secure
with for 5/8 x 5.5” bolts. Repeat for the other
UPRIGHT.
www.dero.com
© 2016 Dero
|
1-888-337-6729
DERO DECKER™
Installation Instructions – Double Sided
6
7
Starting at one end of the CROSS BEAM and
working your way to the other, place a DOWN
CANTILEVER ASSEMBLY and an opposing UP
CANTILEVER ASSEMBLY in place and secure
them with four 5/8 x 5.5” bolts. Check to make
sure the CANTILEVER ASSEMBLIES are at 90º
to the CROSS BEAM. After tightening the fourth
bolt, retighten all four bolts. Repeat until all
open CROSS BEAM positions are filled.
Place the LOWER TRAYS in position on the
ground with alternating UP and DOWN LOWER
TRAYS. The LOWER TRAYS should be in
between the CANTILEVER ASSEMBLIES. The
front edge of the UP and DOWN LOWER
TRAYS are coincident and 62” from the back
edge of the UPRIGHT base flange. Secure
the LOWER TRAYS to the ground with wedge
anchors.
www.dero.com
© 2016 Dero
|
1-888-337-6729