IPL, POULAN, PO175A42LT, 2011
Transcription
IMPORTANT MANUAL DO NOT THROW AWAY 5000 REPAIR PARTS MANUAL MODEL: PO175A42LT WARNING: Read this Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury. LAWN TRACTOR ALWAYS WEAR EYE PROTECTION DURING OPERATION Visit our website: www.poulan.com 532 44 67-46 09.28.11 BD Printed in the U.S.A. HOW TO USE THIS MANUAL This manual is designed to provide the customer with a means to identify the parts on his/her tractor when ordering repair parts. The illustrations may or may not represent the actual assemblies; therefore, it is not recommended to use this manual as a guide to assemble or disassemble the tractor. Some hardware and parts are drawn larger in order to more readily identify them. Each tractor has its own model number. The model number for your tractor can be found on the fender under the seat. When ordering parts, always give the following information: • Product - “Tractor” • MODEL NUMBER - “PO175A42LT (96048002400)” • Part Number • Part Description TABLE OF CONTENTS SCHEMATIC ..................................................................................................................3 ELECTRICAL ............................................................................................................. 4-5 CHASSIS ................................................................................................................... 6-7 DRIVE......................................................................................................................... 8-9 ENGINE .................................................................................................................. 10-11 STEERING ............................................................................................................. 12-13 MOWER DECK ...................................................................................................... 14-15 MOWER LIFT ...............................................................................................................16 SEAT ............................................................................................................................17 DECALS .......................................................................................................................18 PARTS AND SERVICE ................................................................................................20 2 TRACTOR - MODEL NO. PO175A42LT (96048002400), PRODUCT NO. 960 48 00-24 SCHEMATIC SCH11 BATTERY RED SOLENOID M FUSE AMMETER (OPTIONAL) BLACK WHITE S B G STARTER RED A WHITE M A1 L A2 ATTACHMENT CLUTCH (CLUTCH OFF) BLACK CLUTCH/BRAKE (PEDAL UP) GRAY REVERSE SWITCH (NOT IN REVERSE) BLACK BLACK BLACK 2 BLACK 3 BLACK BLACK SEAT SWITCH (NOT OCCUPIED) BLACK BLACK 1 6 GRAY SHORTING CONNECTOR CHASSIS HARNESS IGNITION UNIT (OPTIONAL) SPARK PLUGS GAP (2 PLUGS ON TWIN CYL. ENGINES) HOUR METER BLUE BLACK NOTE YOUR TRACTOR IS EQUIPPED WITH A SPECIAL ALTERNATOR SYSTEM. THE LIGHTS ARE NOT CONNECTED TO THE BATTERY, BUT HAVE THEIR OWN ELECTRICAL SOURCE. BECAUSE OF THIS, THE BRIGHTNESS OF THE LIGHTS WILL CHANGE WITH ENGINE SPEED. AT IDLE THE LIGHTS WILL DIM. AS THE ENGINE IS SPEEDED UP, THE LIGHTS WILL BECOME THEIR BRIGHTEST. BLACK /WHITE JUNCTION CONNECTOR BLACK FUEL LINE 12V POWER OUTLET (OPTIONAL) BLUE FUEL SHUT-OFF SOLENOID (IF SO EQUIPPED) CHARGING SYSTEM OUTPUT 3 AMP DC @ 3600 RPM 28 VOLTS AC MIN. @ 3600 RPM (CHARGING SYSTEM DISCONNECTED) RED LIGHTING SYSTEM OUTPUT 5 AMP AC @ 3600 RPM DIODE ALTERNATOR ORANGE LIGHT SWITCH 14 VOLTS AC MIN. @ 3600 RPM (LIGHTS OFF) BROWN BLACK HEADLIGHTS IGNITION SWITCH POSITION CIRCUIT OFF RUN/OVERRIDE M+G+A1 B+A1 RUN START B+A1 B + S + A1 “MAKE” L+A2 3 6 6 3 2 5 5 2 1 4 4 1 CHASSIS HARNESS CONNECTOR (MATING SIDE) DASH HARNESS CONNECTOR (MATING SIDE) 3 WIRING INSULATED CLIPS NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR SERVICING OF UNIT, THEY SHOULD BE RE-INSTALLED TO PROPERLY SECURE YOUR WIRING. NON-REMOVABLE CONNECTIONS REMOVABLE CONNECTIONS TRACTOR - MODEL NO. PO175A42LT (96048002400), PRODUCT NO. 960 48 00-24 ELECTRICAL T06S 22 With 12V Outlet Option 33 30 79 103 21 87 59 34 With Service Minder Option 27 43 42 46 40 26 41 25 16 71 90 2 102 29 28 55 105 4 TRACTOR - MODEL NO. PO175A42LT (96048002400), PRODUCT NO. 960 48 00-24 ELECTRICAL KEY NO. PART NO. DESCRIPTION 1 2 8 16 21 22 25 26 27 28 29 30 33 34 40 41 42 43 55 71 79 87 90 102 105 532 16 34-65 874 76 04-12 532 19 32-28 532 17 61-38 532 17 56-88 532 00 41-52 532 41 28-94 532 17 51-58 873 51 04-00 532 19 88-85 532 19 27-49 532 19 33-50 532 41 19-35 532 11 07-12 532 40 10-98 817 72 04-08 532 13 15-63 532 19 25-07 817 06 05-12 532 44 15-44 532 17 52-42 532 19 78-02 532 43 53-95 532 41 97-81 532 40 75-68 Battery Bolt Hex Hd 1/4-20 unc x 3/4 Box Battery Switch Interlock Harness Socket Light Bulb, Light #1156 Cable Starter 6 Ga. BL/Red 14.5 Fuse Nut Keps Hex 1/4-20 unc Cable Ground 18" Rear Battery Blk 6 Ga. Switch Seat Switch Ign Key/Chain Switch Light/Reset Harness Ign Screw 1/4-20 unc x 1/2 Cover Terminal Red Solenoid Screw 5/16-18 x 3/4 Harness Ign. Chass. Socket Asm. Bulb Switch Interlock Clutch Cover Terminal Pigtail Rev. GT Vatr. Switch Reverse NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 5 TRACTOR - MODEL NO. PO175A42LT (96048002400), PRODUCT NO. 960 48 00-24 CHASSIS 29 212 18 14 151 5 137 176 130 150 176 176 130 177 175 182 236 235 68 34 68 36 196 181 235 176 194 37 68 183 194 236 213 68 183 138 68 68 180 287 181 162 218 228 58 189 217 189 194 52 189 159 228 189 152 Chassis-tex_ALPHA_3 159 6 189 TRACTOR - MODEL NO. PO175A42LT (96048002400), PRODUCT NO. 960 48 00-24 CHASSIS KEY NO. PART NO. DESCRIPTION 5 14 18 29 34 36 37 52 58 68 130 137 138 150 151 152 159 162 175 176 177 180 181 182 183 189 194 196 212 213 217 218 228 235 236 287 532 41 17-64 532 40 61-79 532 42 67-41 532 18 75-69 532 19 61-25 817 06 05-12 532 42 09-86 873 68 05-00 532 41 22-80 817 49 05-08 532 41 63-58 532 18 49-21 532 40 97-30 532 18 44-61 532 18 75-68 532 19 95-35 817 00 06-12 532 14 24-32 532 19 32-43 532 40 07-76 532 19 52-28 532 41 50-63 532 40 30-25 532 19 30-57 874 52 05-20 817 00 05-12 873 90 05-00 532 41 45-79 532 19 54-02 874 76 05-12 532 40 91-67 532 19 63-95 532 19 51-61 532 40 61-29 873 93 05-00 817 60 04-06 Dash Hood Grille Insert Reflective Plate Engine Screw 5/16-18 x 3/4 Fender Nut Crown Lock 5/16-18 Drawbar Upper Screw Thdrol. 5/16-18 x 1/2 Screw #10 x 0.750 Bumper Hood Cupholder Duct Intake Air Bracket Pivot Shield Browning Screw 3/8-16 x 3/4 Screw 1/4 x 1/2 Crossmember Screw 10-24 x 5/8 Bushing Steering Chassis Bushing Mtg. Fender Crgo. Dash Lower Bolt 5/16-18 x 1-1/4 Screw 5/16-18 x 3/4 Nut Lock Hex Flange 5/16-18 Console Asm. Deck Lift Lens Bar Bolt Hex Hd. 5/16-18 unc x 3/4 Rod Pivot Hood X-Piece Hood Stop Stud Fastener Spacer Fender Nut Lock 5/16-18 Screw 1/4-20 x 3/8 NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 7 TRACTOR - MODEL NO. PO175A42LT (96048002400), PRODUCT NO. 960 48 00-24 DRIVE 70 185 74 143 56 184 221 35 303 167 42 64 303 189 187 160 160 203 50 299 190 161 131 188 51 300 298 302 165 52 51 51 295 176 301 174 178 166 305 186 49 297 51 233 172 125 232 131 175 116 125 22 1 2 73 23 125 166 116 205 37 99 33 296 73 296 8 drive-tex_VATR_6 TRACTOR - MODEL NO. PO175A42LT (96048002400), PRODUCT NO. 960 48 00-24 DRIVE KEY NO. PART NO. 1 – – – – – – 2 22 23 33 35 37 42 49 50 51 52 56 64 70 73 74 99 116 125 131 143 160 161 165 166 167 172 174 532 12 35-83 532 42 10-63 532 10 69-33 812 00 00-01 532 19 77-22 532 12 17-49 532 12 48-72 872 11 06-14 532 19 43-27 873 90 06-00 532 19 43-26 532 19 72-53 532 19 62-00 532 44 03-23 874 49 05-44 532 14 24-32 532 42 73-40 873 90 05-00 817 00 05-12 876 02 03-12 817 49 05-08 532 16 94-84 532 10 57-09 532 19 62-12 532 42 91-64 532 40 52-57 532 41 56-64 532 19 72-89 DESCRIPTION Transmission, Gentrans (415663) (Order parts from transaxle manufacturer.) Key.Square .2.0 x .1845/.1865 Rod Shift Knob E-Ring. #5133-75 Rod.Brake.Parking. Lt.Tex Washer.25/32 X 1 1/4 x 16 Ga. Cover.Pedal.Blk.Round Bolt.Rdhd.3/8-16Uncx1-3/4.Gr 5 Idler.Flat.910"Offset Nut, Hex, Flangelock 3/8-16 Idler.V-Groove.Offset Belt.Drive.100.97" Shaft Asm.Pedal.Brake Control Console Bolt.Hex.Flghd.5/16-18.Gr.5 Screw.Hex.Wsh.Hi-Lo.1/4x1/2unc Rod Bypass Nut, Lock Hex Flange 5/16-18 unc Screw.5/16-18 x 3/4.Smgml.Tap/Bl Pin Cotter 3/32/ x 3/4 Screw.Thdrol.5/16-18 x 1/2 Tytt Retainer.Clip(M).Dia.290 Spring.Return.Clutch.6.75 Bushing.Shaft.Brake.Hand Contr Nut Push .625 Latch.Brake.Parking Strap Torque LH/RH Nut.Push..500 KEY NO. PART NO. DESCRIPTION 175 176 178 184 185 186 187 188 189 190 203 205 221 232 233 295 296 297 298 299 300 301 302 303 305 532 41 56-77 532 19 62-14 532 19 74-56 532 44 15-04 872 11 06-22 532 19 43-21 819 13 32-10 532 19 43-23 532 19 43-17 532 19 43-18 819 11 11-16 532 12 17-48 532 40 31-87 874 78 07-16 532 40 52-96 532 42 03-06 532 42 04-71 532 42 02-23 532 41 56-94 532 41 56-83 532 41 56-81 532 41 56-80 532 41 56-66 872 11 06-18 532 41 56-92 Shaft Asm Shift Arm.Clevis.Rod.Shift Spring.Shift.Gt.2006 Handle.Parking Brake Bolt.Rdhd.3/8-16Unc x 2-3/4 Gr.5 Spacer.Retainer Washer.13/32 x 2 x 10 Ga. Link.Clutch.Ground Drive Bellcrank.Groundrive.Nstg/Nstl Keeper.Bellcrank.Drive.Ground Washer 11/32 x 11/16 x 16 Ga. Washer.25/32 x 1-5/8 x 16Ga. Retainer.Spring.Clip.Handle Bolt.Fin Hex.7/16-14 x 1 Gr5 Washer.Serrated Pin Clevis 183 Od x 1.260 Long Screw Thdrol 5/16-18 x 3 Nut Push 1/4 Pin Clevis Cbl. Brk. Variator Bracket Mount Idler Keeper Idler Rear Pulley Idler V-Groove Pulley Idler Flat 2.0 Od Bolt Rdhd Sgnk 3/8-16 x 2-1/4 Cable Brake Variator NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 9 TRACTOR - MODEL NO. PO175A42LT (96048002400), PRODUCT NO. 960 48 00-24 ENGINE 1 21 45 20 79 84 97 122 18 96 15 69 12 37 42 28 37 85 90 9 29 OPTIONAL EQUIPMENT Spark Arrester engine-tex_BS_36 10 2 TRACTOR - MODEL NO. PO175A42LT (96048002400), PRODUCT NO. 960 48 00-24 ENGINE KEY PART NO. NO. 1 – – – – – – 2 9 12 15 18 20 21 28 29 37 42 45 69 79 84 85 90 96 97 122 532 13 73-52 532 19 43-19 532 40 19-85 532 40 75-45 532 43 02-20 532 17 05-51 817 72 04-08 532 40 11-37 532 13 71-80 532 12 34-87 810 04 07-00 873 51 04-00 532 16 52-91 532 19 23-34 817 06 06-20 532 17 39-37 817 00 06-16 819 09 14-16 817 67 04-12 532 42 19-22 DESCRIPTION Engine, B&S 31C707-3487-G1 (438654) (Order parts from engine manufacturer.) Muffler Exhaust B&S Keeper Belt Pulley Engine Tank Fuel Front Cap Asm Fuel Control Th/ch Flag Screw Hex Thd Cut 1/4-20 x 1/2 Line Fuel Kit Spark Arrestor (Flat Scrn) Clamp Hose Washer Lock 7/16 Nut Keps Hex 1/4-20 unc Gasket Eng 1 313 Id Tin Plated Screw Socket Head 5/16-18 x 3/4 Screw 3/8-16 x 1-1/4 Bolt Hex 7/16-20 x 4 Gr. 5-1.5 THR Screw 3/8-16 x 1 Washer 9/32 x 7/8 x 16 Ga. Screw Thdrol 1/4-20 x 3/4 Extension Drain Oil NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm For engine service and replacement parts, call the toll free number for your engine manufacturer listed below: Briggs & Stratton 1-800-233-3723 Engine Power Rating Information The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and corrected in accordance with SAE J1995 (Revision 2002-05). Torque values are derived at 3060 RPM; horsepower values are derived at 3600 RPM. Actual gross engine power will be lower and is affected by, among other things, ambient operating conditions and engine-to-engine variability. Given both the wide array of products on which engines are placed and the variety of environmental issues applicable to operating the equipment, the gas engine will not develop the rated gross power when used in a given piece of power equipment (actual “on-site” or net power). This difference is due to a variety of factors including, but not limited to, accessories (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this Series engine. 11 TRACTOR - MODEL NO. PO175A42LT (96048002400), PRODUCT NO. 960 48 00-24 STEERING ASSEMBLY 26 72 33 45 1 20 71 21 13 16 63 28 22 64 60 28 57 63 9 57 8 74 66 7 67 2 9 7 8 19 120 74 121 59 6 35 74 74 67 4 6 58 5 14 15 68 8 14 69 61 13 62 70 15 13 53 steering-tex_STDHRR_2_r2 12 TRACTOR - MODEL NO. PO175A42LT (96048002400), PRODUCT NO. 960 48 00-24 STEERING ASSEMBLY KEY NO. PART NO. DESCRIPTION 1 2 4 5 6 7 8 9 13 14 15 16 19 20 21 22 26 28 33 35 45 53 57 58 59 60 61 62 63 64 66 67 68 69 70 71 72 74 120 121 532 42 45-43 532 41 81-68 532 40 30-87 532 40 30-88 532 12 49-31 532 12 17-48 812 00 00-29 532 12 12-32 532 12 17-49 810 04 06-00 873 54 06-00 532 42 93-74 532 19 47-29 532 41 12-91 532 18 67-37 532 42 05-37 532 42 46-91 817 00 06-12 810 04 05-00 532 19 47-32 819 11 38-12 532 18 89-67 532 40 74-65 532 19 47-47 532 19 47-48 873 97 10-00 532 19 47-40 532 19 47-41 817 00 05-12 532 19 98-49 871 02 07-48 532 19 47-37 873 90 07-00 532 19 91-62 532 19 61-97 532 19 07-52 532 42 89-82 532 12 49-37 532 41 56-89 817 49 05-08 Wheel, Steering Axle Asm., Front Spindle Asm., LH Spindle Asm., RH Washer Thrust 0.75 x 1.23 Washer 25/32 x 1-5/8 x 16 Ga. Ring, Clip #T5304-75 Cap, Spindle Washer 25/32 x 1-1/4 x 16 Ga. Washer Lock 3/8 Nut, Crown Lock 3/8-24 unf Shaft Steering Plate Steering Boot Steering Adapter, Wheel Steering Strg. Supt. Lower Insert, Wheel Steering Screw 3/8-16 x 3/4 Washer Lock 5/16 Gear, Sector Plate Washer 11/32 ID x 2-3/8 OD x 12 Ga. Washer Hardened .793 x 1.637 x .060 Bracket Upstop Bolt Shoulder Sector Pivot CFM Washer Thrust Sector Steering Nut Flange Lock 5/8-11 Draglink, LH Draglink, RH Screw 5/16-18 x 3/4 Retainer Clip Spring Steering Bolt Hex Fghd 7/16-14 x 3 Serr Bushing PM Front Axle Nut Lock Flange 7/16-14 Gr. 5 Washer 1.5 x .505 x .118 Bracket Deck Susp. Front Shaft Extension Steering Bolt Fin Hx 5/16-18 x 4 w/Patch Bearing Col. Strg. Bracket Locator Screw 5/16-18 x 1/2 NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 13 TRACTOR - MODEL NO. PO175A42LT (96048002400), PRODUCT NO. 960 48 00-24 MOWER DECK 195 70 122 67 7 152 195 40 57 145 43 59 42 60 56 30 123 68 7 37 55 57 63 147 64 30 113 38 40 46 56 30 38 36 33 34 47 192 32 144 208 31 30 21 1 62 23 21 69 188 189 19 24 26 21 113 6 29 189 188 15 6 14 19 20 13 27 69 69 11 42_D_man-tex_LT_32_r1 8 14 25 TRACTOR - MODEL NO. PO175A42LT (96048002400), PRODUCT NO. 960 48 00-24 MOWER DECK KEY NO. PART NO. 1 6 7 8 11 532 19 99-11 532 19 51-86 532 41 63-58 532 19 30-03 532 13 89-71 13 14 15 19 20 21 23 24 25 26 27 29 30 31 32 33 34 36 37 38 40 42 43 46 47 55 532 19 28-72 532 18 72-81 532 11 04-85 532 19 65-39 532 15 97-70 873 68 05-00 532 19 25-57 532 10 53-04 532 19 70-26 532 11 04-52 532 40 30-04 532 13 14-91 532 17 39-84 532 18 76-90 532 19 74-73 532 40 02-34 872 11 06-12 532 19 73-79 819 13 13-16 532 43 25-20 873 90 06-00 532 19 84-10 532 19 72-56 532 13 77-29 532 19 72-50 532 43 71-10 DESCRIPTION Mower Housing Arm Suspension Screw #10 x 0.750 BOS Thread Bolt/Washer Asm 7/16-20 unf Blade, 42" Hi-Lift (For bagging or discharge) Shaft Assembly, Mandrel Housing, Mandrel Bearing, Ball, Mandrel Bolt, Shoulder Baffle, Vortex Nut, Crownlock 5/16-18 unc Bracket, Deflector Cap, Sleeve Spring, Torsion, Deflector Nut, Push Shield, Deflector Rod, Hinge Screw Thdrol Rolling Wsh Hd Washer, Spacer Pulley, Mandrel Nut, Toplock, Flanged Bolt Carr Sh. 3/8-16 x 1-1/2 Gr. 5 Pulley, Idler 4.50 RAW Washer 13/32 x 13/16 x 16 Ga. Keeper Belt Mandrel Nut, Lock Flg. 3/8-16 unc Spring Torsion Brake Spring Torsion Retainer Screw Thd Roll 1/4-20 x 5/8 Bracket Clutch Cable Arm, Idler KEY NO. PART NO. 56 57 59 60 62 63 64 67 68 69 70 113 122 123 144 145 147 152 188 189 192 195 208 -- 532 19 90-92 817 00 06-16 532 14 10-43 532 19 72-61 872 11 06-16 532 19 94-77 532 19 97-90 532 40 30-12 532 42 96-36 872 14 05-05 532 19 83-32 817 00 05-10 532 19 72-58 532 19 72-59 532 19 92-04 532 19 31-97 532 40 19-71 532 43 51-11 532 19 51-61 873 90 05-00 532 19 72-60 817 00 06-12 817 67 06-08 532 19 28-70 -- 532 41 52-41 DESCRIPTION Spacer, Retainer Screw Hexwsh Thd 3/8-16 x 1 Guard, Tuv Idler (94) Arm Brake Mower Bolt Rdhd Sqnk 3/8-16 unc x 2 Arm Brake Mower Linkage Brake Handle, Clutch Cable V-Belt Bolt Rdhd Sqnk 5/16-18 x 5/8 Clutch Asm. Manual Screw 5/16-18 Keeper Belt Eng. LH Keeper Belt Eng. RH Keeper Belt Pulley Idler Primary Spring Return Cable Clutch Manual w/Spr. Stud Fastener Nut Lock Hex Flange Bracket Brake Stand LH Screw Hexwsh Thdr 3/8-16 x 3/4 Screw Thdrol 3/8-16 x 1/2 Mandrel Assembly (Includes housing, shaft assembly, and bearing only - pulley/nut/washer and blade bolt/washers not included) Replacement Mower, Complete NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 15 TRACTOR - MODEL NO. PO175A42LT (96048002400), PRODUCT NO. 960 48 00-24 MOWER LIFT 87 7 90 98 89 10 3 97 100 2 88 97 91 87 101* 89 89 lift-tex_17_r3 KEY NO. 2 3 7 10 87 88 89 90 PART NO. 532 42 20-27 532 19 52-31 532 41 15-55 532 19 63-14 532 19 42-09 532 41 07-10 819 19 19-12 532 19 42-08 87 *Key 91 may be substituted for Key 101 KEY NO. 91 97 98 100 101 DESCRIPTION Shaft Asm., Cross Lift Lever Asm., Lift RH Grip, Lever Spring Torsion Pin Cotter 7/16 Bow Tie Lock Spring Lift Assist Washer Clear Zinc Pin Cotter 5/16 Bow Tie Lock PART NO. 532 19 51-81 817 00 06-12 532 19 52-70 873 93 06-00 532 40 70-03 DESCRIPTION Link Lift Susp Mower Rear Screw 3/8-16 x .75 Smgml Tap/R.Z Link Lift Susp. Front Mower Nut Centerlock 3/8 -16 unc Link Asm. Lift Fixed NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 16 TRACTOR - MODEL NO. PO175A42LT (96048002400), PRODUCT NO. 960 48 00-24 SEAT ASSEMBLY 1 8 8 7 8 7 8 10 14 42 19 16 6 21 37 5 15 6 37 12 21 13 2 17 3 seat-tex_knob_3 KEY NO. 1 2 3 5 6 7 8 10 12 13 14 PART NO. 532 40 30-17 532 18 01-66 532 14 06-75 532 14 50-06 873 80 06-00 532 12 41-81 532 17 18-77 532 44 18-05 532 19 93-70 532 12 12-48 872 05 04-12 KEY NO. 15 16 17 19 21 37 42 DESCRIPTION Seat Bracket Pivot Fender Strap, Asm Fender Clip Push-in Hinged Nut, Lock w/Ins. 3/8-16 unc Spring, Seat Cprsn Bolt 5/16-18 unc x 3/4 w/Sems Pan, Seat Bracket Mnt. Bushing Snap Bolt 1/4-20 x 1-1/2 PART NO. 532 13 43-00 532 12 37-40 532 12 39-76 532 19 93-72 532 17 18-52 873 80 05-00 532 19 93-71 DESCRIPTION Spacer Split Spring CPRSN Plate Nut Lock 1/4 Knob Seat Bolt, Shoulder 5/16-18 Nut, Lock 5/16-18 unc Cup Washer NOTE: All component dimensions given in U.S. inches 1 inch = 25.4 mm 17 TRACTOR - MODEL NO. PO175A42LT (96048002400), PRODUCT NO. 960 48 00-24 DECALS 7 2 12 12 6 15 9 4 1 5 5 8 3 10 1 KEY NO. 1 2 3 4 5 6 7 8 9 PART NO. 532 44 68-01 532 44 66-06 532 43 10-92 532 17 05-63 532 43 20-72 532 41 16-58 532 43 19-82 532 43 52-86 532 43 19-86 DESCRIPTION Decal, Fender RH/LH Set Decal, Replacement Decal, Engine HP Decal, Warning Decal, Dash Lower Decal, Fender Warning (E&F) Decal, Ins Str Wh Dceal, Warn. Spark Decal, Fender WHEELS & TIRES 1 2 5,8 4,10 7 3,9 6 11 wheel_1 18 KEY NO. 10 12 15 ------ PART NO. 532 16 03-96 532 43 19-83 532 14 50-05 532 16 69-60 532 40 95-05 532 41 12-73 532 44 67-45 532 44 67-46 KEY NO. 1 2 3 4 5 6 7 PART NO. 532 05 91-92 532 06 51-39 532 10 62-22 532 05 99-04 532 18 33-37 532 12 49-57 532 12 49-59 8 9 10 11 -- 532 19 33-38 532 42 05-31 532 12 49-26 532 17 50-39 532 14 43-34 DESCRIPTION Decal, V-Belt Sch. Decal, Hood RH/LH Decal, Caution, Battery Decal, Bypass Pad Footrest LH Pad Footrest RH Manual,Operator's,(English/French) Manual, Parts,(English /French) DESCRIPTION Cap, Tire Valve Stem, Valve Tire, Front Tube, Front (Service item only) Rim Assembly, 6" Front Fitting, Grease (Front wheel only) Bearing, Flange (Front wheel only) Rim Assembly, 8" Rear Tire, Rear Tube, Rear (Service item only) Cap, Hub Axle Sealant, Tire (10 oz. Tube) SERVICE NOTES 19 PARTS AND SERVICE This product has been expertly engineered and carefully manufactured to rigid quality standards. As with all mechanical products, some adjustments or part replacement may be necessary during the life of your unit. For Parts and service, contact our authorized distributor: call 1-800-849-1297 • For replacement parts, have available the following information: a. Model Number/Manufacturer's I.D. Number b. Description of part. For Technical Assistance: call 1-800-829-5886 For a Parts Manual, go to our website: www.poulan.com NOTE: HOP provides parts and service through its authorized distributors and dealers; therefore, all requests for parts and service should be directed to your local dealer(s). The philosophy of HOP is to continually improve all of its products. If the operating characteristics or the appearance of your product differs from those described in this Manual, please contact your local dealer for updated information and assistance. 20
Similar documents
- Lawn Mower Manuals
Keeper Belt Eng. LH Keeper Belt Eng. RH Keeper Belt Pulley Idler Primary Spring Return Cable Clutch Manual w/Spr. Stud Fastener Nut Lock Hex Flange Bracket Brake Stand LH Screw Hexwsh Thdr 3/8-16 x...
More informationIPL, YTH 1542 XP (YTH 1542 XPT), 96043000602
Nut Hex Flange Toplock M8-1.2 Bolt 5/16-18 unc x 1 w/Sems Screw 3/8-16 x 1 Screw 3/8-16 x 1 Bushing
More informationIPL, Poulan, PO125-97RB, 96061034900, 2012
Screw Hex Thd Cut 1/4-20 x 1/2 Engine Briggs Model 219807-3402-B1 (438614) (Order parts from engine manufacturer.) Muffler Gasket Muffler Shield Brn/Dbr Guard Control Choke Kit Spark Arrestor Tank ...
More informationIPL, YTH 1542 XP G, 954567253, 2003-03, Ride Mower
Kit Spark Arrestor (Flat Scrn) Tank Fuel 4.0 Rear Cap Asm Fuel Gauge Clamp Hose Blk Line Fuel Plug Drain Oil (Order Parts from Engine Manufacturer) Stem Tank Fuel Screw Hexwsh Thdr 3/8-16 x 3/4 Nut...
More informationIPL, GTH260 Twin, 96041004502, 2008-09, Tractor
Nut Lock Hex Flange Nut Lock Flange 7/16-14 Gr. 5 Stud Fastener w/"D" Anti-Rotation Arm Susp. Mower Rear Bolt Shoulder Keeper Belt Idler Bolt Carr. Sqnk. 3/8-16 x 2-1/4 Bolt 3/8-16 x 2-1/2 Gr. 5 Sc...
More information