NEWS 2013 01 Seat Cover Puller Bracket Set for

Transcription

NEWS 2013 01
Seat Cover
For the optimal protection of vehicle seats.
Measurements: 131 x 74cm (51.5″ x 29″)
Material:
Stain resistant synthetic material
Just slips over the headrest and the top of the back, so it fits almost every car.
Colour may vary.
•
•
One size fits most
Washable
6550010
Seat Cover "PICHLER"
Puller Bracket Set for Denso Injectors
A
For injector removal with slide hammer or the universal injector puller.
The angle of the diesel line connection determines which hook is to be
used. Recommended slide hammers: 6148800 8kg or 6148790 5kg.
Recommended universal injector puller: 60385395
Content 3 pieces including illustrated instructions:
A
90384870
puller bracket Ø16mm / connection 28.5°
special nut M12x1,5
B
90384880
C
90384875
puller bracket Ø17mm / connection 23°
Suited for:
Denso injectors
90384865
Puller Bracket Set for Denso Injectors 3 pcs
B
C
Brass Injector Shaft Cleaning Kit
For professional cleaning the injector shaft without damaging it.
The kit contains the most important tools for the perfect cleaning the injector
shaft. The bore to the combustion chamber is closed by plugs.
Content:
90391465
4 sealing plugs with setting tool
Holder for tube brushes with flexible bit
holder ¼"(custom made)
12 brass tube brushes (3 of each; Ø18,
19, 12 and 24mm)
2 long brass tube brushes
2 brass wire end brushes ø17mm
Guide for brass wire end brush
Brass Injector Shaft Cleaning Kit 24 pcs
Pichler Tools Ltd. • Ednaston Business Centre • Hollington Lane • Ednaston • Ashbourne GB-DE6 3AE
T: +44 1335 368010 M: +44 7885 244338
www.pichler-werkzeug.com • office@pichler-tools.com
1/1
NEWS 2013 02
Extraction Adapter female M12 - male M18x1.5
Extraction Adapter M12 for removing the injector with the slide hammer from
90384430.
Male thread:
M18 x1.5
Female thread: M12
60384402
Extraction Adapter male M18x1.5 - female M12
Extraction Adapter female M16x1.5 - female M18x1.5
Pull Adapter for M16 x1.5 thread, such as used in Facom tools.
Female to
Female to
M16 x1.5
M18 x1.5
60385216
Pull Adapter female M16x1.5 - female M18x1.5
Extraction Adapter female M10 - female M12
Practical for injector removal using with e.g. slide hammer, extractor claw and for similar applications.
Female thread: M10
Female thread: M12
60384419
Extraction Adapter female M10 - female M12
Oxygen Sensor Socket HEX22
Easy replacing the oxygen sensor with integrated heat shield in the exhaust manifold.
Hex22 x110mm
½“-drive
Access to the the oxygen sensor is hindered by the closely adjacent
the exhaust manifold heat shield.
•
•
•
•
Diameter stepped.
Time-saving.
Exact fit, no overwinding of the socket.
The heat shield does not need to be time consuming dismantled or destroyed.
Suited for; developed specifically for Ford Fiesta
60455255
Oxygen Sensor Socket HEX22
T: +44 1335 368010 M: +44 7885 244338
1/1
NEWS 2013 03
Bezel Nut Tool 4 Pins UBJ
Drive:
Tool inside Ø:
Tool outside Ø:
Pin spacing:
Pin width:
Pin height:
Pin count:
½“
39mm
26mm
30mm
6mm
7,5mm
4
Suited for: Iveco e.g. Daily 4x4 upper ball joint
91435800
Bezel Nut Tool 4 Pins for Iveco upper ball joint
Bezel Nut Tool 4 Pins LBJ
Drive:
Tool inside Ø:
Tool outside Ø:
Pin spacing:
Pin width:
Pin height:
Pin count:
½“
26mm
35mm
28mm
4mm
6mm
4
Example of use
Suited for: Iveco e.g. Daily 4x4, lower ball joint
91435850
Bezel Nut Tool 4 Pins for Iveco lower ball joint
Test Needle Set with Flexible Tips and Shrink Collets
Makes measuring with multimeters significantly
easier. Connection: 4mm (banana plug)
•
•
•
Capable of piercing cables.
Replaceable tips
(suitable tips unit 100 pcs 9514757).
Suitable for round and flat connectors.
Delivered in a plastic carrying case with
3 pairs of flat connectors sleeves (wide
4.2 and 1 mm, female)
2 pairs of round connectors sleeves (Ø 2
and 1.5 mm, female)
1 pair of needle / pierce connectors (0.5 mm sharpened)
Line extension 4mm, 100cm, male/male
10 needles
9514760
Test Needle Set with Flexible Tips and Shrink Collets
T: +44 1335 368010 M: +44 7885 244338
1/1
NEWS 2013 04
Valve Coupling HR with Hose for Tire Inflation
The HR Valve Coupling makes filling and venting tires quick and easy.
The hydraulic coupling system avoids wear and guarantees
a long tool life. A replaceable sealing ring ensures the
quality for several years.
Can be used with commercially available tire fillers with
female thread ¼" e.g. 9139420, 6139300, 6139400,
6139420, 9139430 etc.
Max. operating pressure:
Dimensions:
Weight:
15bar
Ø 25 x 80mm
55g
Delivery: coupling including 80cm hose to ¼" and illustrated guide
•
•
•
•
•
•
Self-sealing and
self-locking
Quick and easy filling or venting
Effortlessly one-hand operation
Self-sealing and self-locking
Lockable
Accurate test results in filling pressures
Coupling remains at extremely high pressure on the valve
9139410
Valve Coupling HR with Hose for Tire Inflation
Digital Tyre Inflator GL
For checking, filling and venting of tires.
Measuring range: 0 - 12 bar (an accuracy of 0,05 bar)
Response time: 0.25 seconds
Connections: Euro coupling & female thread ¼"
Hose: 80cm
The non-slip, damped rubber casing makes the
electronic pressure sensor shock resistant and extremely robust.
The digital display requires only 2 AAA batteries (approx. 2 years shelf life).
•
•
•
Easy to read digital display
Battery indicator
Plastic strap
9139450
Digital Tyre Inflator GL
Ideal complement to the
Valve Coupling 9139410
T: +44 1335 368010 M: +44 7885 244338
1/2
NEWS 2013 04
Digital Tyre Inflator
•
•
•
•
•
•
•
Digital display
One-hand operation
Automatic shutdown of the LCD display after 5 minutes
With filling lever and release button
Hose with integrated connector
Cold insulated handle
Sturdy rubber coated housing
Specifications:
Weight:
1.1 kg
Dimensions (lxh): 300x75mm
Optional display: bar, kPa or PSI
Measuring range: 0.46 ~ 6.80 bar, 35 ~ 680 kPa, 5 ~ 100 PSI
Hose:
80cm with Thumb lock
Air Connection:
¼" PT
Tolerance:
± 1%
Supplied with ¼" coupling, 80cm hose and 2 AA batteries
9139430
Digital Tyre Inflator
Adapter Set for Removing Injectors
Adapter set for removing Bosch, Denso, Siemens / Continental und
Delphi injectors.
Suitable to our Universal Hydraulic Injector Puller 60385395 or 8kg
Slide Hammer 6148808.
Contains:
60384405
60384406
60384407
60384408
60384410
60384414
60384413
60384172
60384417
60384420
60384423-A
74251005
Extraction Adapter F M14x1.5 / F M18x1.5
Extraction Adapter M M27x1 / F M18x1.5 Siemens
Extraction Adapter M M20x1 / F M18x1.5 Denso
Extraction Adapter M M25x1 / F M18x1.5
Extraction Adapter F M16x1 / F M18x1.5 Toyota 2.2D
Extraction Adapter M M17x1 / F M18x1.5
Box Nut Adaptor
Special Allen socket 10mm with drilling Ø7.5mm
Sleeve Adaptor
Pin Socket
Pins for Pin Socket 60384420
Socket Hex 7/8" Drive 1/2"
Supplied in plastic case with detailed instructions in English.
Suited for:
Bosch, Denso, Siemens / Continental und Delphi injectors.
60384660
Adapter Set for Removing Injectors 12-tlg.
T: +44 1335 368010 M: +44 7885 244338
2/2
NEWS 2013 05
Rivet Head Cutter “Large”
For cutting off aluminium and steel rivet heads.
Length:
Weight:
38cm
1.1 kg
Good for a clean removing of rivets without drilling, chiselling or
grinding. With this tool, rivet heads are removed quickly and
simply without effort. A rotating of the rivets or an elongated hole
like with chiselling can be avoided.
Important: The mandrel must be beaten back before
cutting! (Otherwise the warranty will be void)
•
•
•
For aluminium and steel rivets.
No elongated hole like when chiselling.
Much faster.
Comes complete with safety instructions and a manual.
9251110
Rivet Head Cutter “Large” for aluminium and steel rivets
Rivet Head Cutter “Small”
For cutting off aluminium rivet heads.
Length:
Weight:
20cm
350 gram
This tool has a special tapered cutting head, especially for poorly accessible rivet heads,
for example with loudspeakers.
•
•
•
Special tapered cutting head.
No rotating of the rivets.
No damage to the base material.
Comes complete with safety instructions and a manual.
9251115
Rivet Head Cutter “Small” for aluminium rivets
Magnetic Tray
Magnetic tray made of stainless material.
4 magnetic feet with plastic covers to protect the vehicle.
Dimensions:
Depth:
Weight:
50505055
26.5 x 29 x 4cm
2cm
1,4kg
Magnetic Tray
T: +44 1335 368010 • M: +44 7885 244338
www.pichler-tools.com • office@pichler-tools.com
1/1
NEWS 2013 06
Timing Tool Kit Opel/Vauxhall A14
Time-saving and professionally replacing the timing chain.
•
•
•
Quick and easy handling
Precise adjusted timing
Service suitable
Supplied in a practical case with instructions.
A
Camshaft Locking Plate 43200031
B
Crankshaft Locking Pin 43200032
C
Adjustment Tool for Camshaft Position Sensor 43200034
D
Chain Tensioner Locking Pin 43200033
E
Fixing Tool for Intake Camshaft Adjuster 43200035
Suited for:
Opel/Vauxhall Astra J (from ’10), Meriva-B (from ’10),
Corsa-D (from ’09)
C
D
E
B
A
Motor code: A14NEL(LUH), A14NET(LUJ), A14XER(LDD)
43200030
Timing Tool Kit Opel/Vauxhall A14
Timing Tool Kit BMW N43
For the application designed kit for fast and professional replacing the
timing chain and/or replacing the vanos unit.
•
•
•
Precise adjustment
Easy installation
Time-saving
Supplied in a practical carrying case with illustrated instructions.
Suited for:
BMW
1 series E81/82/87/88
3 series E90/91/92/93
5 series E60/E61
Motor code: N43 B16A/AA, N43 B20A/AA and N43 B20AY from ‘06
43200050
Timing Tool Kit BMW 1-, 3- & 5-series
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 07
Breaker Bar ¾″
Ideal for working on the engine nuts and wheel hub bearing units, where the stability of
1/2″ is no longer sufficient.
Drive:
Length:
•
•
¾″
60cm
Joint handle
Particularly Sturdy
74110250
Breaker Bar ¾″
Impact Socket 24 drive ¾″
For example, the removal & installation of very frozen drive shaft nuts.
Ideal for use with 60cm ¾″ breaker bar 74110250.
Drive:
Driven:
Length:
•
•
¾″
Hex 24 12-point
5 cm
Impact resistant
Outstanding quality
Suited for:
VAG
e.g. Audi, VW, Seat and Škoda
7965240
Impact Socket 24 drive ¾″ 12-point 50 mm long
XZN Bit with Universal Joint 10
Easy and time saving removing the difficult to reach bolts on the drive shaft flange at the
gearbox end.
Driven:
Drive:
Length:
10mm XZN
½″
12.7 cm
Suited for:
VAG
78708010
XZN Bit with Universal Joint 10 ½″
e.g. Audi, VW, Seat and Škoda
XZN Bit with Universal Joint 8mm
Driven:
Drive:
Length:
XZN 8mm
⅜″
12,7cm
Suited for:
e.g. VAG drive shaft
78708000
XZN Bit with Universal Joint 8mm drive ⅜″
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 08
Cooling System Pressure Test Kit
Cooling system tester with pump of fiberglass reinforced plastic, with
quick coupling and drain valve as well as 7 aluminium adapters.
Measuring range:
Adapters:
Hose length:
0 – 2.5 bar
KS 23, 25, 62.1, 65, 85, 90 and UA60J
50cm, with quick coupling
The hard shell case includes the hand pump (with rubber-protected
precision pressure gauge up to 2.5 bar or 36psi), 50cm hose with quick
coupling and 7 adapters.
The universal adapter has a stepped rubber cone and is especially suited for
Japanese vehicles: Ø 18-24mm
9056990
Cooling System Pressure Test Kit
Cooling System Pressure Test and
Tracing of Combustion Gases Kit
For fast and accurate presseure testing and leak detection of the
cooling system.
Measuring range:
Adapters:
0 – 2.5 bar
KS 22, 23, 31, 38 & K60, 33
Including CO2 leak tester for the detection of combustion gases (carbon
dioxide) in the cooling system, caused by faulty seals and cracks in the
cylinder head or engine block.
Supplied in a plastic case with a metal vacuum pump with quick
coupling, adapters: KS 22, 23, 31, 38 & K60, 33.
And also the LT200 CO2 leak tester with 200ml test fluid.
Suited for both diesel and petrol engines.
9056500
Cooling System Pressure Test and Tracing of Combustion Gases Kit
Truck Cooling System Pressure Test
For testing and leak detection in cooling systems of commercial vehicles,
especially trucks.
Content:
Suited for:
DAF
SCANIA
VOLVO
IVECO
RENAULT
MAN
MB
9056200
Aluminium pressure pump with pressure gauge 0 - 2.5 bar, 7 metal
adapters, 54cm hose
XF 95, XF 105
113, 114, 124 and 125
FH 12
Truck Daily 2000 C-series, EURO-Star, EURO-Tech,
Euro-Truck, Strahlis
Magnum
L 2000, TGA, F 90, F2000
Actros, Atego, Axor, ECO 8401, truck 1728,
Sprinter (to incl. model year ‘06), Vito
Truck Cooling System Pressure Test
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 09
Manual Pump Fuel System Bleeding Kit - Metric
Comfortable, rapid bleeding of diesel fuel systems e.g. after replacing
the filter. (Set with metric and SAE adapters: 9011860)
• Adapter Ø 8, 10 mm; metric
• Quick Coupling
• Versatile
The set comes in hard shell case with rubber hand pump and metric,
straight adapters (Ø 8, 10mm) and detailed instructions.
9011870
Manual Pump kit 5 pcs. with Quick Couplings for Bleeding the
Fuel System - Metric (Ø 8, 10mm)
Vacuum-Box Adblue
For emptying the SCR tanks.
Flow rate: 10l/min
Capacity: 10l
Length of the suction hose: 2.5 m
The portable vacuum box with venturi nozzle is suitable for both
mobile and stationary use. The box is used to siphon off the
operating agent AdBlue from the SRC tank.
• Location independence
• Operation with compressed air
8063650
Siphon Off Vacuum-Box Plastic
AdBlue Urea Refractometer
with percentage scale
Fast quality assessment of the operating agent AdBlue
in the SCR system.
Length:
15cm
Is the operating agent Adblue stored for too long or not used up in the
vehicle, it deteriorates.
A small sample taken by a pipette already suffices, to get a clear result.
(Supplied with a pipette)
Suited for: Cars and trucks
61915455
Adblue Urea Refractometer RFM 03_AB with percentage scale
Indicator scale
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 10
Adjustable Bearing Race and Bearing Seal Driver
Universal adjustable bearing and seal press piece.
Reach:
Length:
Ø 18-86mm
18,5cm
Easy to use; - can be adjusted to the suitable diameter by
turning.
•
•
•
Time saving because you never again have to search
for a suitable driver
Lightweight alloy material eliminates damage to race
or housing
Arresting and lockable
6169490
Adjustable Bearing Race and Bearing Seal Driver
Videoscope Mount
Suitable mount for the videoscope 9078050.
The standard ¼" thread makes the mount also suited
for digital cameras and the like.
Length:
Thread:
30cm
¼“
The clamping surfaces of the mount are foam protected.
The ball and clamp base are arresting and lockable.
9078054
Videoscope Mount
Ideal supplement to the
videoscope 9078050
Flexible Extensions for - Inserts
Intermediate element or connector between actuator and socket.
•
•
•
For areas with restricted access
High torque
High quality with articulated steel elements
A
B
⅜"
½"
180°
90°
Length:
23,5cm
22,5cm
Max. torque
180Nm
350Nm
7302090
7402090
Drive
Max. angle
T: +44 1335 368010 • M: +44 7885 244338
A
B
1/1
NEWS 2013 11
Testing and Measuring Accessories Set
Suitable accessories set for all common multimeters with 4mm
banana plugs, but especially for the Power Probe®.
Contents 7-piece, all gold plated connectors:
3 extensions (30, 60, 90cm)
3 conversion adapter (male/male, female/female,
male/crocodile clip)
2 penetrating probes
1 Power Probe® Replacement Tip
41008025
Testing and Measuring Accessories Set
Digital HYBRID-Multimeter CAT III - 20A
Especially designed multimeter for the automotive branch.
Sizes:
Weight:
182mm x 82mm x 55mm
425g (with pouch 895g)
Functions:
Voltage
AC/DC, < 600V
Amperage < 20A
Resistance < 40M Ω
Diode test
Capacitance 1pF – 40mF)
Continuity test
Frequency 1Hz - 40MHz)
Temperature -30 – 1000°C | C° or F° selectable
Dwell angle 4, 5, 6, 8 cylinders
Duty cycle 0.1 - 99%
Pulse width measurement 1 - 20ms
Engine rpm 1.000 – 12.000 | 2 and 4 stroke
Max/Min function
•
•
•
Display 3¾ digit
Polarity is changed automatically
Auto range
Supplied in a textile case with detailed instructions in English, German and French, multimeter in a
protective cover, test leads with probes (90cm), temperature sensor (100cm) and RPM clamp with
sensitivity control (150cm).
60995100
Digital HYBRID-Multimeter CAT III - 20A
T: +44 1335 368010 • M: +44 7885 244338
1/2
NEWS 2013 11
Digital Automotive Multimeter to 10A
Especially designed multimeter for the automotive branch.
Sizes:
Weight:
189mm x 91mm x 32mm
280g (with pouch 450g)
Functions:
Voltage
AC < 750V, DC < 1000V
Amperage < 10A
Resistance < 32 MΩ
Diode test
Continuity
Frequency <23 KHz
Temperature -20 – 750°C | C° or F° selectable
Dwell angle 2, 3, 4, 5, 6 & 8 cylinders
Duty cycle 0.1 - 99%
Engine speed 1.000 – 12.000 rpm | 2 and 4 stroke
•
•
•
Display 3¾ digit
Polarity is changed automatically
Auto range
Supplied in a textile case with detailed instructions in English, German and French, multimeter in a
protective cover, test leads with probes (90cm), alligator clips (90cm), temperature sensor (100cm) and RPM
clamp with sensitivity control (150cm).
60994500
Digital Automotive Multimeter till 10A
Relay Tester 4 &5 pin
Quickly and accurately test of 4 and 5 pin relays.
Size:
Connection:
Voltage:
13 x 7 x 3cm
1,3m long with alligator clips
12 Volt
Relay is tested several times
Operating directly on the car battery
Test results are displayed by a red and a green led.
Suited for: 4 and 5 pin relays (not inverted pins)
Supplied with instructions in English, German and French.
41008070
Relay Tester Automotive 12-Volt for 3 different relays
Suitable for these
relay types
T: +44 1335 368010 • M: +44 7885 244338
2/2
NEWS 2013 12
Universal Glow Plug Elements Extractor Kit
Safely removing broken glow plug tips / heating elements.
When removing extremely burned-in glow plugs often the element
breaks off and is stuck in the glow plug shaft bore to the combustion
chamber. In very unfavourable circumstances breaks the tip below
the glow plug sealing seat. The glow plug tip is then barely visible
and can definitely not be grabbed by any tool.
With this tool a thread is cut in the stripped tip, which subsequently
can be removed with an extraction spindle.
Supplied in a case, including detailed instructions.
•
•
•
•
For all common glow plug sizes.
Thorough cleaning of the glow plug bore.
No removing of the cylinder head.
Tailored, designed for the application tools to ensure a correct and
economical workflow.
Suited for: universal
Glow plug threads M8x1, M9x1 (new from 2013/01), M10x1 und
M10x1.25
90417900
Universal Glow Plug Elements Extractor Kit
Extractor Kit
PSA DV6 /
Ford DLD416
Supplement
PSA
Universal
Extractor Kit
Toyota
Supplement
Toyota
Universal
90417915
M10x1,25
Engine code 1CD-FTV
90417925
M8x1 and M10x1
e.g. Ford, PSA, BMWMini, Mazda, Volvo
90417910
90417920
Screw-in guide M9x1
Guide sleeve M9x1to fit glow plug tips extractor kits 90417900 (before 2013/01), 90417910 and 90417920.
Male thread:
M9 x 1
Drive:
SW 13
Overall length: 54mm
90417919
Screw-in guide M9x1
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 13
Universal Hook Set 30cm
Multi-angled hooks for the removal of e.g. coolant hoses
and similar hard to reach parts.
Blade length: 30cm
Hilt Length: 13,5cm
For easy removal of coolant hoses, safety pins and helps in the removal of difficult to
reach clips or when inserting small springs.
•
•
•
•
Quick-Change Mechanism
Multi-angled
Highly polished hooks
High corrosion resistance
Handle with quick release mechanism
Delivery in a foam tray (43 x 19cm) for the tool trolley.
60476230
Universal Hook Set 4 pcs
Multi-Angled
Universal Hook Set 15cm
Comprehensive set with 8 different hook designs.
Blade length: ~15cm
Hilt Length: 13,5cm
For working in tight spaces e.g. close to the firewall. The
90° hook can be used e.g. to keep leads a side. The long
curved hook provides extra leverage when working on
trucks, farm or road equipment.
•
•
•
•
8 different hook designs
Highly polished hooks
High corrosion resistance
Handle with quick release mechanism
Ideal für O-Ringe
Delivery in a foam tray (43 x 19cm) for the tool trolley with the following hook
shapes: 1 x straight awl, 1 x S-shape, 1 x 90° pick, 1 x 45° pick, 1 x round, 1 x
dual angle, 1 x big 90°, 1 x cotter key puller
60476280
Universal Hook Set 9 pcs
T: +44 1335 368010 M: +44 7885 244338
1/1
NEWS 2013 14
Mityvac Universal Filling System with Flow Control
For clean filling or toping-off e.g. sealed automatic transmissions,
cooling systems, windshield washers, brakes or power
steering reservoirs.
Volume:
5 litres
Maximum pressure:
1.6 bar
Length of dispensing hose: 164 cm
Length of dispensing tube:
33 cm
•
•
•
Quick Change Connector
Pressure gauge directly on the container
Flow and pressure relief valve
Fluid is dispensed under pressure for a smooth continual flow.
Integrated manual pump adds air above the fluid level to
prevent aeration. Internal pump components are sealed
against exposure to fluids. The liquid dispensing hose with
flow control and automatic shut-off valve make the filling
of hard to reach reservoirs possible.
Kit includes: Mityvac fluid dispensing system including 5 litres
fluid reservoir, 10 pcs ATF refill adapter kit, universal master
cylinder adapter, hanging hook, 1.64 m. hose with quick
couplings and detailed instructions.
most automatic cars from Ford, Toyota, BMW, Honda, Nissan, VW, Audi w/DSG, Audi CVT,
Mercedes 722.9, Volvo
Mityvac Universal Filling System with Flow Control 10 pcs
6090865
6090864
6090867
6090868
6090863
5 litres container with
pressure hose, hook
and cannula
ATF refill adapter
kit 10 pcs
Universal master
cylinder adapter
1.64 m. fluid dispensing
hose with
auto-shutoff valve
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 15
Flexible Double End Line Wrench
Flexible Double End Line Wrench to be used on brake piping, hydraulic & pneumatic
connections, power assisted steering, A/C and fuel lines
Sizes: 12/13mm
Can be opened to slip over the brake pipe and closed to fit around the brake pipe nut
completely. The unique geometry makes working on rounded and worn nuts possible. The
more pressure is exerted on the tool, the tighter the grip on the fastener will be. This
guarantees secure work without slipping.
70100012
Flexible Double End Line Wrench SW12/13
Last Chance Wrench Set
For the removal of rusted fittings on the brake-, fuel-, hydraulic- and air
conditioning lines without leaving damage.
⅜”
10 mm (⅜”)
11 mm (7/6”)
12-13 mm (½”)
14 mm (9/16”)
Drive:
Sizes:
•
•
•
Tightening upon worn, damaged or under-sized fittings
3/8” square drive for extra leverage
Compact fold-out wrench heads
Delivery in a practical Foam Tray
60554150
Last Chance Wrench Set 10-14mm 4 pcs.
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 16
Vacuum Brake Bleeder Kit
For quick and effective brake bleeding.
Volume:
Volume refill tank:
Air pressure:
Vacuum:
•
•
•
1.5 l
0.6 l
min 5.5 bar / max 9 bar
0 to -1 bar
Eliminates air pockets in the system by vacuum
Automatic locking lever system
With overflow protection valve
6090866
Vacuum Brake Bleeder Kit
Suitable accessory sets for vacuum pumps (e.g. 6090860):
Diagnostic Adapter Set
11-piece adapter set for use with vacuum pumps for
testing and analysing.
For use with 6mm hose systems. The adapters allow
correspondingly smaller and larger diameters.
60908601
Diagnostic Adapter Set
Brake Bleeding Adapter Set
For a wide variety of hydraulic brakes and clutches. 5pieces:-2 bleed
screw adapters, 2 tapered bleed adapters and
adapter for connecting two 6.4 mm ID tubes.
60908602
Brake Bleeding Adapter Set
Application
example
Vacuum Cap Set
12 rubber caps for plugging vacuum lines.
•
•
For plugging lines from 4 – 13mm (5/32“ – ½“)
Colour coded.
60908603
Vacuum Cap Set
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 17
Wheel Bearing Replacement - Starter Kit
Bearing, Axle Shaft & Hub Set
Universal front wheel bearing set with combined hub/axle
shaft press clamp. The wheel bearing is replaced directly
on the car with a minimum of work. Neither ABS-sensor,
wheel spindle, spring strut nor steering linkage needs to be
dismounted. There is also no need for toe-in adjustment
or for bleeding the brake system.
Estimated working time: 20–30 minutes/side.
Suitable hydraulic cylinders: 16 ton 90251250 and
22 ton 90251260
9146900
Bearing, Axle Shaft & Hub Set
(without hydraulic components)
Use with e.g.
90251250
Hydraulic Cylinder 16 ton
16 tons push and pull hydraulic cylinder in a compact size.
Designed for everyday use in auto repair shops.
Stroke:
Weight:
67mm
3.4kg
The cylinder´s hydraulic pressure can be combined with punching force
when using the punching socket e.g. when pressing a rusted axle shaft.
90251250
Hydraulic Cylinder 16 ton inclusive Punching Socket
22 tons push and pull hydraulic cylinder in a compact size with
automatic return of the piston. Designed for everyday use in auto
repair shops.
Stroke:
70 mm
Weight:
4.7 kg
Lifting force: 22 ton
The cylinder´s hydraulic pressure can be combined with
punching force when using the punching socket e.g. when
pressing out a rusted axle shaft.
90251260
Hydraulic Cylinder 22 ton inclusive Punching Socket M22x2.5
T: +44 1335 368010 • M: +44 7885 244338
1/7
NEWS 2013 17
Compact Wheel Bearing Mounting Tool
Universal tool for mounting the new type of compact wheel bearings,
with or without locking ring.
Suited for:
VW
Audi
Seat
Skoda
Volvo
Ford
Mazda
Landrover
MB
Mitsubishi
Smart
Lupo, Polo, Transporter 5 en Touareg.
A2
Cordoba
Fabia
V50/S40, V70/S80 en XC60
Focus, C-Max, Mondeo, S-Max en Kuga
3, 5, 6, en CX-7
Freelander 2
Vito, Sprinter
Colt
Forfour
For disassembly is another tool needed!
See 91469480 & 91469481
91469470
Compact Wheel Bearing Mounting Tool
Holding Plate VAG
Holding plate for mounting compact wheel bearings. Suited for universal mounting
tool 91469470.
Suited for: VW Lupo, Polo 9N and equivalent models of Audi, Seat and Skoda.
91469471
Holding Plate for Mounting Compact Wheel Bearings VAG
Holding Plate VW
Holding plate for mounting compact wheel bearings. To be used with universal
mounting tool 91469470.
Suited for: VW T5 und Touareg Diesel
91469472
Holding Plate VW
Mounting Ring
Mounting ring for compact wheel bearings. To be used with universal mounting tool 91469470.
Suited for: Ford Mondeo, Mazda 6 und Volvo V70 2007
91469473
Mounting Ring
Holding Plate
Mounting ring for mounting compact wheel bearings. To be used with universal
mounting tool 91469470.
Suited for: Ford Mondeo, Focus C, Mazda 3, 6, Volvo V70 2007-, S40/V50 2004
91469474
Holding Plate
T: +44 1335 368010 • M: +44 7885 244338
2/7
NEWS 2013 17
Universal Compact Wheel Bearing Dismounting Tool
Universal tool for dismounting the new type of compact wheel bearings, with or without locking ring.
It´s adjustable to fit future bearing sizes.
Suited for: VW Lupo, Polo, Transporter T5 and Touareg
Audi A2
Seat Cordoba
Skoda Fabia
Volvo V50/S40, V70/ S80 and XC60
Ford Focus, C-Max, Mondeo, S-Max and Kuga
Mazda 3, 5, 6 and CX-7
Landrover Freelander 2
Mercedes Vito and Sprinter
Mitsubishi Colt
Smart Forfour
This tool can also be used as a hub puller on most other cars, like BMW.
•
•
•
Max pressure 22 ton
Adjustable
Fits future bearing sizes
91469480
Universal Compact Wheel Bearing Dismounting Tool
Dismounting Cone
Dismounting Cone for dismounting compact wheel bearings.
Suited for: Universal; one size fits all
91469481
Dismounting Cone
Hydraulic Spring Compressor
This unique spring compressor is designed to be a helpful and efficient tool
when working on wheel suspensions. With unique adjustment possibilities
and special jaws it covers almost every front and rear spring on light
commercial vehicles all the way down to small passenger cars. It also
covers models like Mercedes C-class and newer BMW models.
The same function can also be used to unload the lower control arm to its
“normal” position when working with ball-joints or sway bars. This is done
directly on the vehicle and reduces the working time considerably.
It comes with a safety strap for extra safe handling.
The unit can be used as a helping hand when working with other
jobs on the suspension system.
Recommended foot pump: 80255560
9159800
(without hydraulic pump)
9159850
Set: Hydraulic Spring Compressor with Hydraulic Foot Pump 80255560
and 4 jaws Ø 70 -160 mm 9159820
T: +44 1335 368010 • M: +44 7885 244338
3/7
NEWS 2013 17
Wheel bearings and hubs on small commercial vehicles
This kit is specially developed for pressing out rusted & glued axle shafts directly
on the vehicle.
Suited for: Commercial vehicles e.g. Ford Transit 00 – 12
Wheel bearing kit front and rear axle.
Pressing-Out Flange Universal 5 holes
Basic Unit
Without spindle, screws, nuts and adapters,
The tool also fits the front wheel hub - where it can be used as a tool for
pressing-out rusted and cemented drive shafts.
9147960
Pressing-out Flange Universal 5 holes, Basic Unit
Special Nuts Set M14x2, 5 pc
For removing the rear wheel bearing or for pressing out the front drive shaft
on a Ford Transit.
9147962
Special Nuts M14x2 5 pieces
Wheel Bearing Set
Removing and installation of the front wheel bearing on Ford
Transit for models ‘00-‘12
61464600
Wheel Bearing Set Ford Transit Front Axle
(without hydraulic components and flange)
Adapter for Hydraulic Cylinder
From 1 ½" to 2 ¼" - UNS
91491550
Adapter for Hydraulic Cylinder
Wheel Bearing Tool Front and Rear Axle
Boxer, Jumper, Ducato
Wheel bearing tool front and rear, Peugeot Boxer, Citroën Jumper & Fiat Ducato. The wheel bearing is
replaced directly on the vehicle with minimal effort. Working time about 40 minutes per side. recommended
cylinder: 90251270 32 ton.
Wheel Bearing Tool Front Axle
For Peugeot Boxer, Citroën Jumper & Fiat Ducato
replacing the wheel bearing of the front axle from ’07.
Supplement to kit 61464585.
61464585
Wheel Bearing Tool Front Axle
T: +44 1335 368010 • M: +44 7885 244338
4/7
NEWS 2013 17
Wheel Bearing Tool Rear Axle
For Peugeot Boxer, Citroën Jumper, Fiat Ducato replacing the wheel
bearing of the rear axle.
61464595
Wheel Bearing Tool Rear Axle
Press Ring
Is used instead of the press ring from and together with set 61464585 on
cars newer then 2007.
Suited for: Peugeot Boxer, Citroën Jumper, Fiat Ducato
61464575
Press Ring
Stroke: 113mm
Weight: 8.3kg
•
•
Designed for everyday use in auto repair shops
Push and pull function
90251270
Hydraulic Cylinder 32 ton incl. Punching Socket M22x2.5
Pressing out of the steering joint on trucks and buses
The superior solution for pressing out the steering joints on vans, buses and trucks with 8.5 ton hydraulic
cylinder with impact function and a specially designed puller. This tool replaces the older types of
mechanical pullers. A tool that increases productivity and security for the mechanics.
Steering Joint Puller
The clamp is special designed to fit on most steering axles and ball-joints on light
commercial vehicles, heavy trucks and buses on the market. Moulded from special steel
to withstand greater force.
9065000
Steering Joint Puller
Hydraulic Cylinder 8.5 ton
A very compact cylinder for pushing and pulling. (8.5 ton)
Stroke:
Weight:
•
•
25mm
1,8kg
Very flexible and easy to use also in narrow areas
Incl. punching socket and adjustable press rod 100mm, M22
• Automatic return of the piston
Hydraulic Cylinder ton 8.5ton Push and Pull Function
90251240
T: +44 1335 368010 • M: +44 7885 244338
5/7
NEWS 2013 17
Replacing ball joints on Ford Transit & MB 211/220
This set contains a 14 ton hydraulic cylinder 90251230 and the press block 91489252. With the proper
tools is the ball joint replaced within 10-15 minutes.
Press Block
Forged press block for changing ball joints etc. No further
reinforcement is necessary, even when pressing with 16 ton.
Makes replacing the ball joints and sway arm bushings of
Mercedes-Benz211 and 220 possible.
Total length:
Inside width:
Weight:
Pressure resistance:
91489252
23cm
16cm
5.8 kg
max. 16 ton
Press Block
Stroke:
Weight:
•
•
55mm
2.5kg
Designed for everyday use in auto repair shops.
With adjustable press rod 92mm, M24
90251230
Ball Joint Socket MB ML
Socket for dismounting ball joints on Mercedes-Benz ML.
91489277
Ball Joint Dismounting Socket for Mercedes-Benz ML
Ball Joint Set Ford Transit
A set for quick and easy replacement of ball-joints on Ford Transit. The work is made
directly on the car with a minimum of dismounting. With this set the whole job will take
only 10 minutes to complete.
91489260
Ball Joint Replacement Set Ford Transit
Ball Joint Set for MB 211 & 220
Set for replacing ball joints on Mercedes-Benz 211 and 220. No need for
dismounting of brake components or reprogramming of the ECU.
91489280
Ball Joint Replacement Set for MB 211 & 220
Sway Bar Ball Joint Set for MB 211 & 220
Set for replacing sway bar ball joints on Mercedes-Benz 211 and 220. The only part
you have to dismount is the sway bar itself. No need for dismounting shock absorbers
or lower slewing bracket fittings.
91489275
Sway Bar Ball Joint Replacement Set for MB 211 & 220
T: +44 1335 368010 • M: +44 7885 244338
6/7
NEWS 2013 17
Important additions (Wallmek ↔ Enerpac)
Hydraulic Wheel Bearing Spindle
Length:
Thread:
45 cm
M20 x 1.5
Is required when using the wheel bearing tools with a hollow piston cylinder.
61471400
Hydraulic Wheel Bearing Spindle M20x1.5x450mm with Nut
Spacer for Enerpac Hollow Piston Cylinder
Washer for the safe use of the hollow piston hydraulic cylinders
(12ton 80251000 or 20ton 80251400).
•
•
Lies exactly on the plunger
No slipping
91491570
Spacer for Enerpac Hollow Piston Cylinder for Wallmek products
Hydraulic Connection Hose
To connect Wallmek cylinders with Enerpac pumps.
50 cm
Length:
Enerpac
Is required when using the Wallmek hydraulic cylinders 14ton 90251230, 8.5ton
90251240, 16ton 90251250, 22ton 90251260 and 32ton 90251270 with Enerpac pumps.
80253015
Hydraulic Connection Hose 50cm with Wallmek and Enerpac Couplings
Wallmek
T: +44 1335 368010 • M: +44 7885 244338
7/7
NEWS 2013 18
Sockets and Tap Adapters Set
with Joint Duo Ratchet Set
Flexible workshop helpers, versatile, ideal for where there is
limited space.
Joint Duo Ratchet Set 70358130
Hex. 13mm – 12 sided
130mm and 190mm ratchet
Finely toothed, slender ratchet ring spanners with a low
return angle.
Joints swivel 90° to each side and are lockable.
Practically combinable with the inserts and sockets
"Extra Short".
Inserts and Sockets "Extra Short".
20-pieces, in a plastic box
Adapter ( -drive 13mm x -drive 3/8" x -output ⅜“)
Torx bits: T15, 20, 25, 27, 30, 40, 45 & 50
Allen bits: SW4, 5, 6, 7, 8 & 10
XZN bits: M4, 5, 6, 8 & 10
Tap Adapter Set 58506000
Compact tap holders with a magnet
-drive13 with detent ball
Adapter 4.9, 5.5, 6.2, 7 & 9mm
58511500
Sockets and Tap Adapters Set with Joint Duo Ratchet Set
Joint Duo Ratchet Set
For quick and easy removing of hard to reach screw connections as on belt covers, thermostat
housings and dashboard.
Size:
Length:
13 / 12 sided
130 mm
190 mm
The 130mm articulated ratchet swivel 90° vertically to each side and is
lockable. The 190mm articulated ratchet swivel 90° horizontally
to each side. Therefore are these ratchets ideal for work
in hard to reach areas.
•
•
Low return angle
Versatile
70358130
Joint Duo Ratchet Set 2-tlg.
Practically combinable with
the inserts and sockets
"Extra Short" 58511000
T: +44 1335 368010 • M: +44 7885 244338
1/2
NEWS 2013 18
Tap Adapter Set
For thread cutting in confined spaces in connection e.g. with the
ratchet articulated spanners 70358130.
Adapter
•
•
4.9, 5.5, 6.2, 7 & 9mm
Example of use
-drive13 with detent ball.
Tap holders with a magnet.
58506000
Tap Adapter Set 5 pcs.
Brake Allen Bit Set
Light manipulating hard to reach allen set screws on brake
callipers of the new brake generations.
Drive:
Output:
Length Bit:
13
6, 7, 8 & 9 mm
45 mm
Length ratchet: 13 cm
The swiveling ring ratchet spanner can be set in such an angular
position so that the allen bits can be attached ideally.
9134880
Brake Allen Bit Set
Reversible Double Ring Ratchet Spanner
Sizes:
Length:
•
•
•
•
•
•
16 / 19 + 17 / 18
23 cm
Straight shape
Toothed accurately with 72 teeth
Four different spanner sizes
With reversing lever
Very fine satin finish
Chrome vanadium
9032020
Reversible Double Ring Ratchet Spanner 4 in 1 system 16x19 + 17x18mm
17
18
Double ring
19
23 cm
16
T: +44 1335 368010 • M: +44 7885 244338
2/2
NEWS 2013 19
Nut-Grip® Socket with 2-Fold Detent Ball.
The two balls in the 6-edge opening of Nut-Grip® socket hold the screw securely in the
socket. This enables to work too in inaccessible places.
¼“
⅜“
½“
6 pc
Sizes:
7, 8, 10, 12, 13 &14
8 pc
Sizes:
8, 10, 11, 12, 13, 14, 17 & 19
10 pc
Sizes:
10, 11, 12, 13, 14, 15, 17, 19, 21 & 22
7270500
®
Nut-Grip Socket Set
6 pc, ¼"
7370500
®
Nut-Grip Socket Set
8 pc, ⅜"
7470500
®
Nut-Grip Socket Set
10 pc, ½"
Socket Set 11 pc
Drive: ¼“
Sizes: 4 - 14 mm,
•
•
12 point
Excellent Koken quality
11 pc on a rail
7205300
Socket Set 4 - 14 mm 12 point on a Rail
Socket Set 12 pc
Drive: ⅜“
Sizes: 8 - 19 mm,
•
•
6 point
Excellent quality
12 pc on a rail
7313300
Socket Set 3/8" 12 pc on a Rail 8 - 19 mm
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 20
Window Rubber Removal Tool
For professional dismantling of window rubbers.
Length:
Blade length:
Blade width:
•
21 cm
10 cm
22 mm
Highest quality
recommended for Audi A3 and Toyota
9545050
Window Rubber Removal Tool 169 WM
Torx Set 72 pc ¼″ & ½″
For TX and E-TX screws
TX:
6 Sockets, ¼″
8 Screwdriver Tamper Proof
12 TX Key
10 Bits Tamper Proof, ¼″, 25 mm long
6 Bits Tamper Proof, 10 mm, 30 mm long
9 Bits Tamper Proof, 10 mm, 75 mm long
T10, 15, 20, 25, 27 & 30
T8, 10, 15, 20, 25, 27, 30 & 40
T8, 10, 15, 20, 25, 27, 30, 40, 45, 50, 55 & 60
T7, 8, 9, 10, 15, 20, 25, 27, 30 & 40
T40, 45, 50, 55, 60 & 70
T15, 20, 25, 30, 40, 45, 50, 55 & 60
E-TX:
7 Sockets, ¼″
7 Sockets, ½″
4 Ring Spanners, straight
E4, 5, 6, 7, 8, 10 & 11
E12, 14, 16, 18, 20, 22 & 24
E6 x E8, E10 x E12, E14 x E18 & E20 x E24
Further Tools:
2 Adapter ¼″ & ½″
1 Magnetic Pickup extendable to 66 cm
•
•
Chrome Vanadium
72 pc
7882700
Torx Set 72 pc 1/4″ & 1/2″
T: +44 1335 368010 • M: +44 7885 244338
1/2
NEWS 2013 20
Torque Spanners
ARF 60 ¼“ with
push-thru
With reversible ratchet, fine-toothed.
Working accuracy ±3%
•
ARF 60 ¼″ with push-thru
Supplied in a plastic case with instruction manual (s) and certificate.
ARF - 60
ARF - 80
ARF - 150
1/4″
3/8″
1/2″
5 - 25 Nm
20 - 110 Nm
40 - 210 Nm
In-Lb 45 - 225
Ft-Lb 10 - 80
Ft-Lb 30 - 150
Length
34 cm
44 cm
54 cm
P/N
40600100
40600200
40600300
Drive
Torque
60
80
150
T-Handle Set 32cm
For fast screwing in and out of released and inaccessible screws.
The height-adjustable freewheeling guide sleeve ensures optimum
hand guiding.
Length:
Round Material:
A T-Handle
B T-Handle
C T-Handle
D T-Handle
•
•
•
D
C
32 cm
Ø 10 mm
¼″ with height-adjustable guide sleeve 53100001
⅜″ with height-adjustable guide sleeve 53100002
½″ with height-adjustable guide sleeve 53100003
¼″ bit, with height-adjustable guide sleeve 53100004
T-Handle with comfortable rubber coating.
Fast de-/ assembly by the easy sliding guide sleeve.
Guide sleeve for safe guidance with 2nd hand.
B
A
Supplied in a practical foam insert for the tool trolley.
53100000
T-Handle Set with 4-way Adjustable Freewheeling Sleeve
for rapid turning 4 pc - 1/4″ Bit, 1/4″, 3/8″ & 1/2″
T: +44 1335 368010 • M: +44 7885 244338
2/2
NEWS 2013 21
Hose Clamp Tensioner 9mm
Easy opening and securing hard to reach spring band hose clamps.
Max. clamping range:
Max. clamp pin width:
Total length:
¼″ and thumbwheel
•
•
•
•
72 mm
9 mm
105 mm
The clamp tensioner can be laid aside with a tensioned clamp
Wear-resistant spindle drive (no Bowden cable defects)
Simple low effort use
Low space requirement
60503695
Hose Clamp Tensioner
Opening 9 mm
No slipping off
sideways!
¼″
and thumbwheel
Fuel Filter Lid Mounting Lever UFI
Removing and mounting of UFI fuel filter lids without leakage.
When mounting the filter unit the filter cover can be not closed without forcing it. By tightening the
Torx bolts the lid warps and will be leaking. If the leakage happens later, then diesel leaks
on the multi belt and dissolves it. Further, it can also cause timing belt damage, which
in its turn results in engine damage.
•
•
•
•
No deformation of the filter cover
No solution from the manufacturer available
Complete replacement of the housing at the expense of the workshop
is eliminated (cost saving ca. € 200)
Rubberized contact faces
Suited for:
All diesel vehicles with screwed on UFI fuel filter
housing (e.g. VW 2.0 TDI / 102 PS)
Is needed for the new "Multicar" M27 / M28
61208990
Fuel Filter Lid Mounting Lever
universal for all UFI filter housings
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 22
Universal Injector Shaft Cleaning Set
For optimal cleaning and revision of the injector shaft.
With special brushes the injector shaft wall, the sealing seat
for the injector and the bore for receiving the injector nose
is cleaned.
In case of severe contamination or damage to the sealing
seat. is the seat reworked precise and controlled with the
milling tool, so that again a perfect sealing surface is formed.
Frozen copper sealing rings can be removed from injector
shaft simply and without damage to the cylinder head.
Consists of modules and 1, 1.1, 2, 3 & basic module
9038100
Universal Injector Shaft Cleaning Set Complete
Module 1- Brushes &
Module 1.1 - Brushes Plus
Thorough cleaning of
the injector shaft
Module 2 - Milling
In case of severe
contamination or damage
to the sealing seat
Module 3 - Equipment
Simply removing frozen
copper sealing ring
Injector shaft
Before
/
After
T: +44 1335 368010 • M: +44 7885 244338
Before and after the
application of 90380100
1/3
NEWS 2013 22
Basic Module
Sturdy plastic case "Large" with insert
9038000
Injector Shaft Cleaning Basic Module
Module 1 - Brushes
5 Steel Wire Brushes
Ø 18 mm 9039032
Ø 21 mm 9039029
Ø 26 mm 9039027
Ø 19 mm
Ø 24 mm
9039031
9039028
Brush Holder - 9039036
for steel wire brushes
Bit Holder Flexible ¼″- 9039034
2 End Brushes - 9039012
From steel, Ø 17 mm
Plastic guide for end brushes - 9039016
Pipe Brush - 9049027
300 x 100 x 7.5 mm
Setting tool and sealing plugs 8 & 10mm - 9039008
3x collar 8 mm, 3x collar 10 mm
9038010
Injector Shaft Cleaning Module 1: Brushes
Module 1.1 - Brushes Plus
5 Steel Wire Brushes
Ø 18 mm 9039032
Ø 21 mm 9039029
Ø 26 mm 9039027
Ø 19 mm
Ø 24 mm
9039031
9039028
8 Injector Sealing Seat Tex Brushes
For smoothing the surface
Coarse,
Ø 25 mm 9039002
Coarse,
Ø 19 mm 90390021
Fine,
Ø 25 mm 9039004
Fine,
Ø 19 mm 90390041
Holder for Tex brushes - 9039003
Pipe Brush - 9049027
300 x 100 x 7.5 mm
9038011
Injector Shaft Cleaning
Module 1.1: Brushes Plus
T: +44 1335 368010 • M: +44 7885 244338
2/3
NEWS 2013 22
Module 2 - Mill-Cutters
For precise and controlled revision of damaged or heavily contaminated sealing seats.
3 Sealing Seat Mill-Cutter
120° Ø 17 : 18,8 mm 90390421
180° Ø 15 : 17 mm
90390431
180° Ø 17 mm
9039044
Base Unit 9039046 with 3 cones and depth stop 90390485
Centring cone Ø 16.7 – 22.0 mm
9039049
90390493
90390495
Cutting Grease - 60200035
Cartridge 300 gram
Allen Key 3 mm - 151.2103
Allen key long, with ball head
9038020
Module 2: Fräsen
Module 3 - Equipment
Injector sealing ring extractor set for extracting frozen copper sealing rings from the injector shaft without
damaging the cylinder head.
Universal Sealing Ring Extractor - 6039070
To extract the frozen copper sealing rings from injector shaft
without damaging the cylinder head.
With M10 thread for using it with the slide hammer.
Suited for: CDI engines e.g. MB, Opel/Vauxhall,
and Renault especially with 2,2L (G9T) &
2,5L (G9U), Nissan and PSA engines
Slide Hammer 1.35 kg - 60390750
M10 connecting thread
Flexible Lamp BAL - 40103000
41 cm long, 66 cm long with protective pipe
End Ø 5 mm
9038030
Module 3: Equipment
T: +44 1335 368010 • M: +44 7885 244338
3/3
NEWS 2013 23
Recall because of brake problems Chevrolet / Vauxhall
Chevrolet / Vauxhall call, because of possible brake problems, 49,000 cars in the workshops. In the
affected vehicles is in the factory the wrong brake fluid been filled according to "kfz-betrieb online".
In the workshop the brake fluid and if necessary also the ABS module is replaced. For this are a maximum
of 140 minutes budgeted.
The following vehicles are affected:
Aveo and Kalos '09 till '11, Epica '08 till '10, Lacetti and Nubira of ‘07 and '08, Matiz and Spark '07 till '09
and Captiva from '07 till '10. Also the Vauxhall Antara, which is identical to the Captiva.
For a professional and time-saving repairing is reservoir adaptor nr.61A p/n80646100 needed, which is
often not available in the Chevrolet and Vauxhall workshops.
Reservoir Adaptor 61A (B648W)
Cadillac
Chevrolet
Chrysler
Daewoo
Ford
General Motors
Mazda
Pontiac
Vauxhall
SsangYong
80646100
Alero ‘99, Blazer ‘99, Camaro ‘99, Captiva ‘07, Corvette ‘96, HHR ‘07, Hummer
H2 & H3 ‘03, Trans Sport ‘99, Trail Blazer ’01 & Trax
Vision
Evanda ‘03
Fiesta 08
Vehicles equipped with ITT ABS Mk.IV
2 ‘07, 6 ‘02, MPV ‘01, Premacy & RX-8 ‘03
Mokka
Korando, Musso
Reservoir Adaptor Nr 61A B648W
Reservoir Adaptor 77 (B668)
Peugeot
SsangYong
Subaru
Suzuki
300M 2.7 Executive ‘99, Neon Sport 16 V ‘96, New Yorker, Sebring ‘01, Stratus
‘99, Grand Voyager ‘99
C-Crosser ‘07
Explorer, Maverick & Ranger ‘96, Navigator (USA) ‘01
Accent ‘05, Atos ‘99, Centenial ‘99, Coupe ‘99, Elantra ‘01, Grandeur ‘05, H-1
Starex ‘98, H-1 ‘01, Lantra, Lantra II ‘95, Matrix, Pony, Santa Fe ‘01, Sonata,
Terracan, Tucson, XG 30 / XG 350
Jaguar S-Type V8 ‘99
Jeep Cherokee ‘95
Carens ‘99, Carnival ‘05, Cee’d ‘07, Cerato ‘05, Joice, Magentis ‘01, Picanto ‘05,
Proceed ‘07, Rio ‘03, Soul ‘09, Sportage ‘05
121 ‘88 - ‘03, MPV ‘99, MX-5 ‘99, Tribute ‘01
Mini Cooper (Rover) till ‘88
Galopper ‘99, Lancer ‘03, Outlander ‘03, Pajero 3.2 ‘01, Pinin, Santamo, Space Runner ‘99, Space Wagon (GDI)
‘99, Station Wagon ‘03
100 NX ‘93, 200 SX ‘95, 350Z ‘03, Almera ‘95, Maxima QX ‘95, Micra, Murano Z50 ‘06, Noblesse ‘05, Pathfinder
& RS1 ‘05, Patrol GR TD6 ‘99, Pick Up ‘01, Primera ‘93, Primera ‘95, Rodius ‘05, Serena, Sunny ‘93, Terrano II
‘99, Vanette Cargo ‘95, X-Trail ‘01
4007 ‘06
Actyon ‘07, Korando ‘03, Kyron ‘05, Musso E32 ‘01, Noblesse ‘05, Rexton, Rodius ‘05
Forester ‘99, Impreza 4 WD ‘98, Impreza WRX ‘01, Legacy & Kombi ‘99, Legacy ‘05, Libero ‘93, Outback ‘89
Baleno with ABS & 1.3 GS & GL ‘96, Baleno Holiday ‘99, Vitara & Grand & XL-7 ‘01
80647700
Reservoir Adaptor Nr. 77 B668
Chrysler
Citroën
Ford
Hyundai
Jaguar
Jeep
Kia
Mazda
Mini
Mitsubishi
Nissan
T: +44 1335 368010 • M: +44 7885 244338
1/2
NEWS 2013 23
Reservoir Adaptor 81/82 (B674)
Daihatsu
Honda
Isuzu
Vauxhall / Opel
Copen ‘03
Civic ‘96, Civic (EJ 9) ‘99, Concerto, CRV, CRX 1.6 ‘97, HR-V ‘99, Insight ‘99, Legend ‘91,
Logo ‘99, Odyssey (US-Minivan) ‘99, Prelude ‘92, S ‘00 ‘99
D-Max ‘05, Frontera ‘89, Montery ‘89, Rodeo ‘05, Trooper ‘89
Campo, Frontera
80648100
Reservoir Adaptor Nr. 81/82 B674
Reservoir Adaptor 83 (B676)
Suzuki
Alto ‘96, Wagon R+ ‘99
80648300
Reservoir Adaptor Nr. 83 B676
The reservoir adapter is needed for the operation of fully automatic,
ABS-compatible brake service equipment.
E.g. Brake maintenance device G12N 8064300 or G20N+ 8064255.
Brake Caliper Piston Spreader UNI
Brake Piston spreader for retracting without damage the piston when fitting new brake pads.
•
•
•
•
•
Versatile
Less effort through the spindle drive with reversible ratchet
Professional and damage-free brake repairs
Exchange of the pressure plates not necessary
Can be adapted to caliper shape and number of the
pistons (1-6)
Suited for:
universal for fixed and floating calipers
61306000
Brake Caliper Piston Spreader
T: +44 1335 368010 • M: +44 7885 244338
2/2
NEWS 2013 24
Universal Cylinder Leakage Test Set
Set for pressure drop testing of diesel engines through the
glow plug hole.
A
B
C
Universal Compression Test Adapter 60920000
Cylinder Leakage Tester 60965505
Matching Screw-on Adapter 60915800
A Universal Compression Test Adapter
Universal tool (M8x1, M9x1, M10x1 & M10x1.25)
for testing the compression.
Supplied in a practical plastic case,
including instructions.
•
•
Highly versatile by combinations of guides, sealing cones and adapters.
Precisely fitting, tailored to the application tools for a quick and
accurate result.
B Cylinder Leakage Tester
• Gauge Ø 80 mm
• 1 m hose
• Working range: 6 to 10 bar (scale 0 to -100 %)
• Quick coupling
C Fitting Screw-on Adapter
Adapter with valve, female thread M12x1.5 & quick coupling
60965510
Universal Cylinder Leakage Test Set
Compression Test Adapter Set 3 pc.
For pressure drop and compression testing of petrol engines.
Fitting cylinder leakage tester 60965505.
Length: 24cm
Thread: M10x1, M12x1.25 & M14x1.25
•
•
•
Flexible version
Highest quality
NW5 quick coupling
9091200
Compression Test Adapter Set 3 pc.
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 25
Impact Ring Spanner 27
Hex:
Length:
Weight:
Material:
•
27 mm
18 cm
350 g
Tempered steel
Particularly robust form
71400270
Impact Ring Spanner 27
Socket Set Specially for Calipers
E-Torx:
Length:
Drive:
•
E 18, E 20, E 22, E 24
38 mm
½“ and hex 27 mm
Heavy Duty
Suited for: commercial vehicles
79402000
Socket Set Specially for Calipers Torx E18 to E24, 38mm long drive 1/2" and hex 27
Line Wrench Set (Brake line screw connection)
Reliable and damage-free loosening rusted brake line fittings.
The special profile applies on a large area at the resilient flanks of the hexagon fittings
and spares the edges
Socket Set Specially for brake lines: drive hex19
HEX 10 (new) 61343303
HEX 11
61343301
HEX 13
61343302
Articulated Line Wrench HEX 19 open 90509190
•
•
•
•
•
Especially for hard to reach wheel brake cylinders or
ABS pumps.
A spinning of the heavily rusted fitting profiles
is almost impossible.
Compared to conventional sockets significantly
better distribution of force on the fitting
Damage to the fitting and possibly necessary
brake line replacement can be avoided
Especially suited to small mounting positions
Suited for: Universal
61343310
Line Wrench Set 4 pc. articulated line wrench
drive hex 19 open sockets hex 10, 11 & 13
61343300
Line Wrench Set 3 pc. articulated line wrench
drive hex 19 open sockets hex 11 & 13
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 26
Driveshaft Socket ¾″ 36mm 12 point
Simple release of glued screw connections.
Size:
Drive:
Length:
Outside-Ø:
36mm 12 point
¾″
47 mm
42 mm
Due to the high release torque of the drive shaft screw connection, does it
happen frequently that the ½" original socket cracks.
•
Heavy duty
Suited for:
VAG, e.g. VW Golf, Polo etc.
Glued in drive shaft double hexagon head bolt
79633600
Driveshaft Socket ¾″ 36mm 12 point VAG
Pin Spanner Drive Shaft Slotted Nut
Secure and proper removing & mounting the drive shaft nut.
Model:
Drive:
4 pegs (round)
½″
The very firm and deep in the wheel hub situated slotted nut cannot
be reached without this spanner.
•
•
•
Secure grip, heavy duty.
Damagefree removing & mounting the drive shaft.
Proper assembly with by the manufacturer prescribed torque.
Suited for:
Suzuki Jimny
61424100
Pin Spanner Drive Shaft Slotted Nut Suzuki Jimmy
Slotted Nut Spanner MB
Model:
Pin width:
Drive:
In- & outside-Ø:
4 pins
7.5 mm
¾″
52 / 63 mm
For removing and mounting of the supporting joint retaining slotted nut.
Very sturdy spanner with outside ring for better guidance.
Suited for:
MB M-class front & rear axle (163/164)
61435800
Slotted Nut Spanner MB Supporting Joint M-class front & rear
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 27
Impact Socket Set 17, 19 & 21mm - Super Impact
Especially suitable for mounting and dismounting
using an impact wrench >1000 Nm.
Drive:
Sizes:
Length:
½"
Hex 17, 19 & 21 mm
86 mm
The high strength chrome molybdenum alloy with
spring-steel ring counteracts the force and thus
ensures a very high durability.
•
•
•
•
Plastic covered for damage-free working on
aluminium rims
Plastic sleeve replaceable
Colour coded according the size
Chrome molybdenum
79416810
Impact Socket Set 1/2" 3 pc 17, 19 & 21mm
Impact Wrench 1/2" - Silent
Quiet and handy ½" impact wrench for changing wheels and similar.
Idling speed:
Drive:
Torque:
Inlet size:
Operating pressure max.:
Average air consumption:
Weight:
Mechanism:
Noise Level:
•
•
•
10.000 rpm
½"
949 Nm
¼"
6.3 bar
368 l/min
2 kg
Twin Hammer
93.7 dB
Selection of forward/reverse is made safe and easy on the back
of the wrench.
In 2- or 3-stage adjustable.
Supplied with German & English instructions.
9235000S
Impact Wrench 1/2" 10.000 rpm Torque 949 Nm - 1600NM
at 6.3 bar, Silent; 93.7dB
T: +44 1335 368010 • M: +44 7885 244338
1/2
NEWS 2013 27
Impact wrench 1/4" Mini
Handy mini impact wrench with 90Nm break loose torque.
Idling speed:
Drive:
Torque:
Inlet size:
Operating pressure max.:
Average air consumption:
Weight:
Length:
Noise Level:
Hose:
Vibration:
•
•
•
10.000 rpm.
¼“
90 Nm (forward/reverse)
¼" female
Drehmoment6.2 bar
Auswahl
3stufig (L/R)
105 l/min
0.9 kg
118 mm
98.2 dB(A)
9-13 mm
2.96 m/s
Ideal for working in the engine compartment
ergonomically perfect contoured handle
One-hand reversing button and speed control
80305055
Impact Wrench 1/4" MINI max. Torque 90/90 Nm at 6.2 bar INDUSTRIAL EQUIPMENT
Universal Tensioning Line
The universal tensioning line is a very useful utility, when it comes to
tightening something to or to secure on a vehicle. Easy adapting the
cable to the required length and easy releasing by the releasing lever.
Capacity max:
25 kg
Tensioning line length:
1800 mm
Tensioning line thickness: 4 mm
Weight:
0.05kg
Tensioner pulley from die-cast zinc
•
•
•
Safe suspension of calipers during service
(No damage to brake lines due to improper tensile load)
Secure tying down of hoods, tailgates, doors and similar
Ideal for dent repair
Included parts: High strength nylon rope
Zinc die cast ratchet
2 galvanized hooks
80251140
Universal Tensioning Line with Hooks and Ratchet
T: +44 1335 368010 • M: +44 7885 244338
2/2
NEWS 2013 28
Relay Pliers Set
For safe installing and removing relays, even the smaller ones.
•
•
•
•
Jaws made of special steel
Fully insulated plastic handles with spring
Grips the outer edges of the relay
No more levering which means; no bent connectors
A straight version 604552310
180 mm long: for straight pulling & plugging of the relay.
Suited for e.g. Opel, Ford, Mazda, Chrysler, Nissan, VW PKW,
Mercedes-Benz, MAN and IVECO LKW
A
B
B 70° angled jaws 604552320
200 mm long: for removal and replacement of relays in
confined spaces. Suited for e.g. Opel, Renault & Nissan
60452300
Relay Pliers Set 2 pcs straight and 70°
angled jaws
B
A
Flexible Socket Screwdriver 7
Simple unscrewing and screwing difficult to reach mountings e.g. under the dashboard and boot trim.
Size:
7mm
Magnetic, for a secure hold of the screw
Shank length: 20 cm
Total length: 32 cm
•
•
•
Long, lean and flexible shank
Versatile
For difficult to reach mountings
Ideal for working in the engine compartment or e.g. for the hard to reach
panels in Vauxhall Isignia, Astra J, Zafira C.
50807100 Flexible Hose Clamp Socket Screwdriver 7 with magnetic insert
T: +44 1335 368010 • M: +44 7885 244338
1/2
NEWS 2013 28
Deburring Tool Interior & Exterior
Secure, time-saving deburring of inside and outside of pipes (especially brake lines).
Max. inside Ø:
Max. outer Ø:
Length:
Weight:
•
•
•
•
3-12 mm
4-14 mm
12.5 cm
180 g
Chatter-free deburring.
Retractable tip.
Robust metal construction.
Suitable for copper, brass, steel and plastic.
61332310
Deburring Tool Internal to 12mm and
External to 15mm
Transmission Output Bearing Puller
For the removal of the gearbox bearing, without causing damage.
•
•
•
•
No solution from the manufacturer available.
Slip off save, friction-locked, accurately fitting
grab half sleeves.
Uniform force distribution across all rollers
Centred constant removal process
The bearing of the main shaft cannot be removed without
damaging the shaft. By the bayonet lock with special puller
spindle, is the sleeve puller locked to one removing unit.
Comes with Puller, M14 spindle and assembly paste.
Suited for:
61078205
Opel Agila, Suzuki Splash
and others with the identical gearbox
Transmission Output Bearing Puller Opel Agila, Suzuki
Splash and others with the identical gearbox
T: +44 1335 368010 • M: +44 7885 244338
2/2
NEWS 2013 29
Universal Camshaft Drive Gears Locking Tool
This tool makes it possible to rotate the camshaft or hold the drive wheels during removing.
Length:
Weight:
Range:
•
•
•
39 cm
380 gram
105 - 150 mm (gearwheel Ø)
Very thin tool for maximum access.
Quick and easy to use.
Maximal grip force.
9039510
Universally adaptable to
the gear 105 - 150mm
Universal Camshaft Drive Gears Locking Tool
Screwdriver Set with Converting Handle
Powerful loosening, quick dis- and assembling.
T-Grip:
10.5 cm
Blade length: 16 cm
Chrome-Molybdenum-Vanadium
8 exchangeable blades ¼":
PH1 / flat-tip 4
PZ1 / flat-tip 5
PZ2 / flat-tip 6
PZ3 / flat-tip 7
PH2 / PH3
HEX5 / HEX6
TX20 / TX25
TX30 / TX40
•
•
•
•
Maximum torque by T-grip
One handed conversion to T grip function
Optimum durability
Practical belt pouch
52130000
One handed conversion
Screwdriver Set 10 pc. in a Belt Pouch
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 30
Universal Thrust Piece Set
For removing and installing wheel bearings, bushings, etc.
49 thrust pieces: 18 - 65 mm (respectively increasing by 1 mm)
and 74 mm
1 grip, designed for max. 2 thrust pieces
1 chuck, length: 22 cm
•
•
With the separately sold thrust piece-mounting adapter
80257066, the thrust pieces can be used with a pneumatic
hammer (e.g. 80257000 or 80257001)
Also suitable for use in the workshop press.
9145030
Universal Thrust Piece Set 51 pcs
Thrust Piece-Mounting Adapter
For operating thrust pieces from the universal thrust piece set 9145030 with a pneumatic hammer.
(E.g. Vibro Impact 80257001 or 80257000).
Length: 11.2 cm
Shaft reception: Ø 10 mm
80257066
Thrust Piece-Mounting Adapter for operating thrust pieces
from the universal thrust piece set 9145030
Pneumatic Hammer Vibro Impact Short
For removal of taper seat connections, bushings, wheel
bearings and rusted screw connections.
Weight:
Blows per minute:
Chisel shank:
Air Inlet:
Air consumption:
Length:
2.2 kg
2100
10.2 mm
¼“
280l/min
26.5 cm
The pneumatic hammer produces a very strong precise impact
pulse, which can be used to support the replacing of e.g.
silentblocs and wheel bearings. The different shapes of the four
impact-resistant adapters ensure the best possible transmission
of this shock pulse and a wide variety of possible use.
80257001
Pneumatic Hammer Vibro Impact Set, basic device with 4 inserts
T: +44 1335 368010 • M: +44 7885 244338
1/2
NEWS 2013 30
Lambda Sensor Vibro Hinged Socket
For easy releasing frozen lambda sensors.
Length: 20 cm
Swivel head inside: 22mm
Swivel Head outside: 30mm
A pneumatic hammer produces a strong shock pulse
with a high frequency. This vibration shock is transmitted
through the specially developed hinge directly on the
release socket. The transmitted vibration increases the
release torque, solves corroded connections and
promotes the penetration of rust solvents.
•
•
•
Easy to assemble
Safe to handle
Time and cost saving
60457600
Lambda Sensor Vibro Hinged Socket 22
For operating a pneumatic
hammer is needed.
Punch Pliers 6mm
Total length: 230 mm
Total weight: 360 g
Max. sheet metal thickness: 1.2 mm
Hole diameter:
6 mm
Very handy and smooth-running pliers with die for body panels up
to 1.2 mm. Due to the large, recessed jaw opening is this tool also
suitable for working in stepped and angled panels. Through the
built-in return spring jamming of the die in the sheet metal is avoided.
9401000
Punch Pliers "EDMA" 6.0 mm
Punch Pliers 5mm
These pliers have the same properties as 9401000, but with a
hole diameter of 5mm.
9401005
Punch Pliers "EDMA" 5.0 mm
T: +44 1335 368010 • M: +44 7885 244338
2/2
NEWS 2013 31
Oil Filler Funnel
For easy and clean topping up of the engine oil. Filler funnel made of
durable plastic with a connector for interchangeable adapters.
Capacity:
Length:
•
•
•
ca. 1 litre
30cm
Clean and environmentally friendly
Time-saving
Interchangeable adapters
The Filler Funnels is a great help to prevent that during topping up the oil
the engine compartment get contaminated by dripping oil. The spilled oil
causes odours and runoff on the ground.
61217001
Filler Funnel with connector for interchangeable adapters
Oil Filler Angle Adapter
With limited space in the engine compartment, the angular aluminium
extension is an ideal addition to filling funnel 61217001.
The extension is rotatable and in angle adjustable. The angular
extension is fitted between the adapter and filler funnel.
61217006
Oil Filler Angle Adapter for Filler Funnel and Adapters
Oil Filler Adapters
61217002
61217003
61217004
61217005
61217008
Bayonet
Thread n°1
Thread n°2
Thread n°3
Guide n°4
Audi, BMW, Dodge,
Mercedes, Toyota
und VW
Toyota, Lexus
Subaru
Honda, Nissan,
Renault
New VAG models
T: +44 1335 368010 • M: +44 7885 244338
1/2
NEWS 2013 31
Oil Filler Funnel with Bayonet Lock
Topping up to 2.3 litres of engine oil clean and professionally.
•
•
•
Capacity:
ca. 2.3 litre
Length:
33cm
Bayonet Lock
Special funnel with bayonet lock for a direct and tight connection to the
engine oil filler hole. 2.3 litre capacity.
Supplied with spare spring and seal.
e.g. Audi, BMW, VW, Seat, Skoda, DB, Chrysler, Toyota
and much more.
9120056
Oil Filler Funnel with Bayonet Lock
Truck Axle Oil Pan
Practical for removing the half shafts or drive shafts.
Length:
25 cm
31.5 cm
Width:
Height:
15.5 cm
Weight:
1 kg
Capacity:
2.5 litres
Drip tray made of chemical-resistant, shatter-proof plastic with a
smooth and wear-resistant surface. Use on removing the stub
axles or drive shafts.
Particularly suitable for trucks
61211555
Truck Axle Oil Pan
T: +44 1335 368010 • M: +44 7885 244338
2/2
NEWS 2013 32
Installation Sleeves 8-pc Set
For installation of new brake discs and drums with integrated
wheel bearings.
•
•
•
No damage to the integrated wheel bearings
Quick and safe
8 different sizes for all current vehicles with these brakes
Without installation sleeves these will tilt on the spindle. When
attempting to pull the drum or disc from the spindle the wheel
bearings will fall apart irreparably. With this precision installation sleeves
set the tilting is safely avoided.
Insert the appropriate sleeve into the integrated bearing. This way the
two inner rings are pre-adjusted. Now slide the brake drum or disc with
the sleeve over the threaded stub of the spindle (oil sparsely) onto the
fitting until it stops. Works without a hammer or such.
For the latest
generation of
brakes
Suited for:
Citroën
Nissan
Opel
Peugeot
Renault
C4 (04-), C4 Coupe (04-), C4 Limousine (04-)
Primastar (01-)
Vivaro (01-)
207 (06-), 207 CC (07-), 307 CC (03-), 307
Kombi (02-), 307 Limousine (00-), 307 SW (02-)
Clio III (05-), Clio III Grandtour (05-), Espace IV
(02-), Grand Scenic (04- ), Grand Scenic (04-),
Laguna II (01-07), Megane I (98-03), Megane II
(03-), Coupe/Cabrio (02-), Megane II Limousine
(02-), Megane II, Modus (04-), Scenic I (99-03),
Scenic II (03-), Traffic II (01-), Vel Satis (02-)
91469450 Installation Sleeves Set for brake discs and drums with integrated wheel bearings Renault / PSA
Inner and outer Puller Set (7pc)
Length:
Weight:
Span:
•
•
•
31,5cm
2,4kg
inside: 50-70mm
outside: 10-180mm
Can be used as 2 - or 3-arm puller
Self-centering and self-relaxing through stable innerspring
Fast hooking on the legs and locking through a thumb screw
Scope of delivery:
3 x Inside legs,
Clamping range Ø 50-170mm, clamping depth 190mm
3 x Outside legs,
Clamping range Ø 10-180mm, clamping depth 190mm
1 x Fine threaded extraction spindle
9040115
Combined 2 & 3 leg puller, inside & outside, exchangeable legs
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 33
Universal Kingpin Tool Set
Universal tool for pressing out the kingpin.
•
•
•
•
Is used together with a 32-ton hydraulic cylinder with punching capability.
No removal of the axl required.
Fitting cylinder
Easy to use.
32ton 90251270
Also suitable for buses.
This set is designed to cover most kingpins on the market, also the conical types.
It’s used with a unique 32 ton hydraulic cylinder designed with punching capability.
This function makes it possible to hammer on the cylinder during maximum pressure.
The punching function is extremely effective and increases the pressure 2 - 3 times.
No removal of the axl required. The tool is easy to use and suitable also for
buses, because here often is worked in confined spaces.
Parts in the set: press block, press spindles 250mm ø31 mm & 140mm ø31 mm,
adaptor plate, press sleeves 145 mm, 42 mm, 130 mm & 42 mm, press socket
65 mm and punching socket M22x2,5
Suited for:
Commercial vehicles with kingpins
61631000
Universal Set for Kingpin without Hydraulic
Cylinder for Light Commercial Vehicles
Stroke: 113mm
Weight: 8,3kg
•
•
Designed for daily use in the vehicle workshop
For pushing and pulling.
90251270
T: +44 1335 368010 • M: +44 7885 244338
1/2
NEWS 2013 33
Universal Hub Puller Set For Trucks
Supplement to 61631000
The tool fits truck hubs with 8 bolt 275 mm and 10 bolt 335 mm.
The tool is used with 32 tons hydraulic cylinder 90251270.
The robust design allows using the full force of 32 ton in
combination with punching with a hammer, which makes it possible
to press out even the hubs with compact bearings like SAF axles.
Parts in the set:
2 support legs
Press spindle 50mm Ø31mm
Press plate
Screws M22x60 (12.9)
Suited for: universal, heavy trucks/busses with 8 bolt
275mm and 10 bolt 335mm
61486855
Universal Hub Puller Set for Trucks
Spring Bolt Set Scania
A tool set for quick dismounting the spring bushing
bolts. The job is done directly on the truck with a
minimum of parts dismounted. When pressing out
the rusted bolts is the 32 ton cylinder used
supported by punching. The punching function
often crucial for a successful result!
Parts in the set:
Press block
Press sleeves 60mm Ø54 mm
Punching socket M22x2.5
6163105
Spring Bolt Set Scania
T: +44 1335 368010 • M: +44 7885 244338
2/2
NEWS 2013 34
Induction Heater Gun Set
Manual device for fast and precise heating of metals and alloys.
Power:
Voltage:
Heat:
Weight:
1600 Watts
220 volts
up to 780 ° C
1.8 kg
Ideal for loosening seized, firmly frozen and rusted components
as well as for forcing open of insoluble adhesive joints.
• Targeted heating.
• No open flame.
• Novel and ergonomic pistol grip.
Supplied in a plastic case with 3 sheathed heating coils (Ø 19 mm,
Ø 22 mm and one flexible) and manual GE/EN.
9535550
Induction Heater Gun Set
Heating Coil Set
8 pcs Standard
Heating Coil Set
6 pcs Extended
Induction Plate For Heating
Surfaces and Mouldings
8x8cm
Bearing Buddy Coil
Length: 84cm
9535555
9535556
95355560
95355558
Extended
Ø
Standard
Individual Coils
Ø 15 mm
Ø 19 mm
Ø 22 mm
Ø 26 mm
Ø 32 mm
Ø 38 mm
Ø 45 mm
Standard
Extended (long)
95355551
95355561
95355552
95355562
95355553
95355563
95355554
95355564
95355555
95355565
95355556
95355566
95355557
95355567
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 35
Impact Socket 46 – 12 sided
For removing and installing the front ball joints.
Drive:
Size:
Length:
•
•
½“
46 mm - 12 sided
100 mm
Chromium-molybdenum steel
Long version
Suited for:
Renault Master III, Renault Mascott,
Opel Movano B, Nissan NV400
91434600
Impact Socket 46mm ½” – 12 sided
Impact Socket 46 – Hexagon
For removing and installing the front ball joints.
Drive:
Size:
Length:
•
•
½“
46 mm - Hexagon
100 mm
Chromium-molybdenum steel
Thin wall version
Suited for:
Renault Master III, Renault Mascott,
Opel Movano B, Nissan NV400
7962460
Impact Socket 46mm ½” – Hexagon
Supporting joint
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 36
Plastic Wedge and Scraper Set
A versatile set of plastic scrapers, levers and wedges.
Material: shape stable and nylon reinforced polypropylene
Applications:
• Gentle on the paintwork removing of clips, emblems, trim, window
mouldings, seals and covers
• Insert tools for cables, seals and plugs
• Scrapers for removing adhesive residue or for cleaning
sensitive surfaces
9611420
Plastic Wedge and Scraper Set 27 pieces
Air Comb Set 3 Pieces
Blowing dust and soiling from air filters, radiators, condensers of
air conditioning systems, etc.
Length: 30.48 cm (12“), 61 cm (24“) und 91.4 cm (36“)
Material: Compressed air tube made of anodized aluminium
•
•
•
•
5 lateral (90 °) placed air-pressure nozzles
Focused and high air flow
Ideal for hard to reach places
Extends service life of the filter
Contents:
P/N
Length
Colour
9562171
30,5 cm (12“)
■ blue
9562172
61,0 cm (24“)
■ red
9562173
91,4 cm (36“)
■ yellow
9562170
Air Comb Set 3 Pieces
Compressed air
T: +44 1335 368010 • M: +44 7885 244338
1/2
NEWS 2013 36
Fender and Front Mask Protector
Protects both fenders, grille, bumpers and lights during repair or maintenance
Size: universal fit for small and medium-sized cars and SUVs
•
•
•
•
•
With wheel cut-outs: allows access to wheels, brakes etc.
Generous cut-outs allow control of vehicle lights
Radiator cut-out allows trial runs with cover fitted
Removable fleece lining - easy to clean
Packed in a carrying case
65500060
Fender and Front Mask Protector
Generous cut-outs for
checking the vehicle lights
Magnetic Tool Tray
The powder coated steel tray sticks to any metal base e.g. a toolbox or
tool trolley, to lifts, tool walls etc.
•
•
•
2 holes for spray cans and the like
1 Extra storage compartment for tools, small parts etc.
Multiple, rubber-coated magnets (1000-1200 Gauss) and edge
protection protect sensitive metal surfaces against scratching
8500090
Magnetic Tray for Workshop Trolleys
Strong hold on
metal surfaces
Rubber-coated magnets protect
sensitive metal surfaces against
scratching
T: +44 1335 368010 • M: +44 7885 244338
2/2
NEWS 2013 37
Automatic Battery Chargers
These chargers are designed to charge the different lead
acidbatteries which are used in cars, motorcycles and
other types of vehicles. The chargers can also be used for
some gel and AGM batteries.
1
6V / 12V
2
Due to the multiple charging steps (7 or 10) empty
batteries can be charged to nearly 100%. The chargers
are equipped with a special feature that allows it also to
repair deeply discharged or "dead" batteries.
•
•
•
•
12V
3 12V / 24V
Safer charging through protection against wrong
connection, short circuit and reverse polarity.
Designed to protect the electronics of the vehicle.
Causes no sparks.
Waterproof in accordance with IP65
The chargers come with connecting clamps and a plug for
the cigarette lighter socket.
Technical Specifications:
9404106
9404112
9404124
P/N
1
Input Supply Voltage:
220-240VAC
50/60 Hz
220-240VAC
50/60 Hz
220-240VAC
50/60 Hz
Battery Type:
12V: 2.2Ah - 40Ah
6V: 2.2Ah - 14Ah
12V: 14Ah – 225Ah
12V: 14Ah - 225Ah
24V: 14Ah - 110Ah
Multiple Charging Steps:
7
10
10
Cut Off Voltage:
14.4V ±0.25V or
7.2V ±0.25V
14.4 ±0.25 or
13.6 ±0.5 or
16.5 ±0.5 VDC
Charging Current:
1.1A ±10%
7.0A ±10% or
5.0A ±10% or
1.5A ±0.5A
Dimensions:
153 x 59 x 37 mm
206 x 88 x 52 mm
206 x 88 x 52 mm
Weight:
0,34 kg
0,73 kg
0,73 kg
2
9404106
Automatic Battery Charger SMART 6V/12V, 1A
9404112
Automatic Battery Charger SMART 12V, 7A
9404124
Automatic Battery Charger SMART 12V/24V, 7A
T: +44 1335 368010 • M: +44 7885 244338
3
14.4 ±0.25 or
28.8 ±2% or
13.6 ±0.5 or
16.5 ±0.5 VDC
7.0A ±10% or
3.5A ±10% or
5.0A ±10% or
1.5A ±0.5A
1/1
NEWS 2013 38
Complement to Injector Removal Kit M9R
When using the sets 60385105 or 60385095 it can happen that the
injector breaks in the middle, just below the injector sleeve. To be
able to continue the removal with the sets mentioned above, must
first the injector sleeve and the remaining small parts be removed
with this complementary set.
Contents: 1 Tap M20x1.5 (Custom Made)
1 Tap Holder
4 HSS Hole Saws
1 Guide for Hole Saw
1 Hole Saw Holder
1 Extraction Spindle M20x1.5 and M16x1.5
The optional cleaning kit consists of a brush holder and 2 pipe
brushes Ø26 mm which are optimal for the engines M9R & M9T.
Suited for:
Renault, Vauxhall/Opel and Nissan engines M9R & M9T
60385200
60385190
Complement to Injector Removal Kit M9R, without optional cleaning kit
Complement to Injector Removal Kit M9R, with optional cleaning kit
Hole saw made of
tough, shatterproof,
and solid
HSS bi-metal
30301900
Perfect complement
to the sets 60385105
or 60385095
Injector Removal Kit OM651
For removing extremely frozen injectors from the cylinder head of a MB OM651 engine.
Contents:
1 1.35 kg Slide Hammer
1 Shaft 110 mm long, IT M10
1 Shaft 205 mm long, OT M12
1 Screw-in Adapter OT M18x1.5 to IT M12
1 Screw-in Adapter OT M18x1.5 to OT M10
1 Extraction Bracket for Piëzo injectors IT M18x1.5
Suited for:
Mercedes Benz, engine code: OM651
60384880
Injector Removal Kit OM651
Extraction Bracket for
piëzo injectors OM651
60384881
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 39
Rear Axle Carrier Bush Tool VW T5
For time saving removal and installation of the two different rear
axle carrier bushings.
By the simply applyable removal and refitting device can replacing
the often very stuck bushes, because of the off-centre bore, be
carried out by one person. The especially for these bushes
designed core puller eliminates another removal tool. Due to the
special construction of the readjustable support socket on the
wishbone, are during removal cutting off of the bush collar or other
press plates not necessary.
•
•
•
No cutting off the bushes collar necessary.
No tilting.
Even extremely stuck bushes can be replaced by
one person.
Suited for: VW T5
61749400
Rear Axle Carrier Bush Tool Kit VW
Electronic Test Set 19 pieces
For testing 6-24 volt circuits. Using a power and ground tester
can be determined whether a positive voltage or ground lies at
the measurement point.
The set includes also 14 probes to make a clean connection to
the connectors or electronic components.
Voltage range: 6-24 volt.
1
Supplied in a plastic box with
1 power and ground tester, cable 1.80 m long*
2 alligator clips*
1 probe needle
1 banana plug ø 4 mm
14 flat probes with plug and pin terminals (ø 0.8 mm - 6 mm)
* Not included in the set 9514795
9514790 Test set with power and ground tester, two alligator clips, test needles,
banana plugs, 14 flat probes
9514795
Test set with power and ground tester, test needles, banana plugs, 14
2
flat probes
1
T: +44 1335 368010 • M: +44 7885 244338
2
1/1
NEWS 2013 40
Chuck up to 3.5 mm with ¼" Hexagon Shaft
Hexagon shaft with keyless chuck.
Clamping range: 0,4 - 3,5 mm
The hexagon shaft (6.35 mm = ¼ ") fits all cordless screwdrivers with ¼" standard
bit holder.
• Can be used in many ways for example in combination with the glow
plug or the element removal kit.
9269034
Chuck up to 3.5 mm with ¼" Hexagon Shaft
Threaded Bushings Inserting Tool Set Long
2 inserting tools (M6 and M7) with a long shaft for deep insertion of the threaded bushing into the shaft.
Threaded Bushings Inserting Tool Set Long 2 pcs M6 and M7
60417880
Thread Repair Kits
For repairing or renewing damaged threads.
With the special drill the destroyed thread is drilled out and the hole
prepared for inserting the threaded sleeve. Afterwards with the inserting
tool the self-tapping threaded bushing is placed.
The repair is possible with a still mounted valve cover.
Contents:
Special drill (3-flute, titanium nitride coated)
Self-tapping threaded bushings
Inserting tool
P/N
Threaded bushing
Number of Bushings
P/N
Threaded bushing
Number of Bushings
6041780
M6
10
9300250
M14x1,5
5
9300070
M7
10
9300170
M16x1,5
5
9300080
M8
10
9300100
M10
10
9300230
M12x1,25
5
9300220
M12x1,5
5
Thread repair kits with additional inserting tool with a long shaft
for deep lying threads:
60417825
M6 without tap
10
60417875
T: +44 1335 368010 • M: +44 7885 244338
M7 with tap
10
1/2
NEWS 2013 40
Thread Repair Kit Complete
Assortment for repairing or renewing damaged threads M5,
M6, M8 und M10
Universal suitable replacement tool with 5 bushings each,
which cut the required new thread with its slots. Four 3-flute
special drills (one for each thread) for making exact round
holes and four inserting tools are included in the kit.
•
•
•
The new thread is much more durable.
Heat-resistant.
No complicated handling of coils.
For quick repair of internal threads in most materials such as aluminium, steel,
plastic, cast iron, etc.
9300280
Thread Repair Kit Complete M5, M6, M8, M10 in a Wooden Box
T: +44 1335 368010 • M: +44 7885 244338
2/2
NEWS 2013 41
Bush Tool Kits VAG
Damage-free removal and installation of the
bushings in the front suspension arm.
•
•
The bushing can be replaced without complete
removing the suspension arm.
No other components(such as hydraulic, press,
U14, etc.) are necessary for the procedure.
Contents:
1
4+5
Adapter (M14) for Bearing Cage
2
Pressing Sleeve Passat, Octavia etc.
3
Pressing Sleeve Polo, Fox etc.
4
Thrust Bearing 35x20x10 mm
5
Bearing Cage for Spindle M20
6
Thrust Plate Passat, Octavia etc.
7
Thrust Plate Polo, Fox etc.
8
Collar Nut M14 for Bush Tool
9
Spindle for M14 / M12
3
6
7
8
61756900
1
2
61756910
9
61756915
10 Anti-Seize Assembly Paste (not shown)
61756910:
VW Polo (6R_, 9N_), Polo sedan (9A4),Fox (5Z1, 5Z3)
Seat Cordoba (6L2), Ibiza IV (6L1)
Skoda Fabia (6Y2), Fabia station wagon (6Y5), Fabia station wagon, Fabia Praktik, Fabia
sedan(6Y3), Roomster (5J) and Roomster Praktik
61756915:
Audi A3 (8P1), A3 Cabrio (8P7), A3 Sportback (8PA), Q3, TT (8J3), TT Roadster (8J9)
VW Beetle (5C1), Caddy III, CC (358), EOS (1F7, 1F8), Golf Plus (5M1, 521), Golf V (1K1), Golf
Variant (1K5), Golf VI (5K1), Golf VI Cabrio (517), Golf VI Variant (AJ5), Jetta III (1K2), Jetta IV (162),
Passat (362/3C2), Passat CC(357), Passat Variant (3C5), Scirocco (137), Sharan (7N), Tiguan (5N),
Touran (1T1, 1T2, 1T3)
Seat Alhambra (710), Seat Altea (5P1),Altea XL (5P5, 5P8), Ibiza III (6K1), Leon (1P1), Toledo III
(5P2)
Skoda Octavia (1Z3), Octavia station wagon (1Z5), SuperB (3T4), SuperB Kombi (3T5), Yeti (5L)
61756900
Bush Tool Kit VAG complete front transverse arm removal and installation
61756910
Bush Tool Kit VAG Polo, Fox and identical front transverse arm removal and installation
61756915
Bush Tool Kit VAG without Polo, Fox etc. front transverse arm removal and installation
Supplied in a
handy plastic case
T: +44 1335 368010 • M: +44 7885 244338
1/2
NEWS 2013 41
Engine Oil Filler Funnel VAG
For professional and without spilling filling of engine oil.
Volume:
Length:
Material funnel:
Type of cap:
•
•
2.3 l
330 mm
plastic
bayonet
Tight contact with the oil filler opening.
No overflowing of the oil.
Suited for:
e.g. Audi, VW, Seat, Škoda 1.6, 1.8 and 2.0l with a timing chain.
Motor codes: CFKB, CUDA, CHHB, CLSA, CLZB, CLHA, CLHB in the Audi A5 Cabrio, A3 from
10/’12, VW Bora, Polo and Golf VII from 11/‘12, Seat Leon from 11/‘12 and Skoda
Octavia from 11/‘12
61217300
Engine Oil Filler Funnel VAG
T: +44 1335 368010 • M: +44 7885 244338
2/2
NEWS 2013 42
Diamond Point & Contact File Set
Super hard, diamond-coated, flexible flat files for cleaning and general filing applications.
Length:
Blade length:
Blade width:
•
•
•
•
165mm
83mm
6 / 9 / 15mm
Ideal for flat contacts.
Highly abrasive and durable, super hard diamond coating.
Non-slip, high-visibility ergonomic handles.
Ultra-thin flexible files make it easy to reach inaccessible spots.
For cleaning and corrosion removal from large spade relays, forklift contacts,
industrial electrical contacts, ground rails and the like. 3-piece set with
stainless steel blade covers a wide range of contact sizes (6, 9 & 15mm).
The 0,7mm ultra-thin flexible files make it easy to reach inaccessible spots.
9514910
Diamond Point & Contact File 3-pieces Set
Flexible Magnetic Pick-Up 70cm
For easy picking up small parts.
Secure hold of magnetic parts by the ring magnet in the tip.
Total length:
695 mm
Magnetic ring; outside-Ø: 13 mm
inside-Ø: 7,5 mm
52600400
70cm
Flexible Pick-Up 695mm with magnetic ring
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 43
A completely new, unique, hydraulic spring compressor with a wide range of uses.
The Compressor can be used on the front and rear struts of almost all cars and
light commercial vehicles, thanks to extensive adjustment possibilities. It also
covers cars like the Mercedes C-class and recent BMW models. All required
yokes and brackets for this are included in set 9159850.
The Compressor can also be used to relieve the struts, when splitting spindles and
struts. This is done directly on the vehicle, which reduces the required time
significantly. Another use is applying pressure from below, thanks to the removable
bracket. This is necessary when working on control arms or ball joints.
•
•
Safety belts for more security.
Absolute universally applicable.
9159800
9159850
Hydraulic Spring Compressor with Foot Pump 80255560 and
4 Yokes for Ø 70 - 160 mm 9159820
Empfohlenes Zubehör:
Hydraulic Foot Pump
• Can be used with all our
hydraulic cylinders
• 2.2m hose
• Drip-free quick coupling
• Oil tank capacity 0.75 litre
• 700 bar
Yoke for Ø 70 - 160 mm
• For multi-link front axles
e.g. Mercedes Benz 220
9159820
80255560
T: +44 1335 368010 • M: +44 7885 244338
1/2
NEWS 2013 43
Hydraulic spring compressor
One device = three functions!
Function 1: Spring Compressor
The Compressor can be used for the front and rear struts of almost all cars
and light commercial vehicles, thanks to its extensive adjustment possibilities.
With security belt for extra safety!
Function 2: Splitting spindles and suspension struts
Another use for the Compressor is to relieve the struts, when splitting
spindles and struts. This is done directly on the vehicle, which
reduces the required time significantly.
Function 3: Transmission Jack
And it can also be used as a transmission jack, thanks to the removable brackets.
T: +44 1335 368010 • M: +44 7885 244338
2/2
NEWS 2013 44
VAG Hub Bearing Unit Removal Kit II
•
•
•
For removing the hub and wheel bearing unit of
VAG vehicles
An optimum support on the steering knuckle is obtained,
due to the milled slots in the Pressing Sleeve.
Suitable for mechanical and hydraulic use.
Suited for:
Audi A3, A4, A6, A8
VW Passat
Seat Exeo, etc.
9169490
VAG Hub Bearing Unit Removal Kit II, with Spindle
9169485
VAG Hub Bearing Unit Removal Kit II, without Spindle
Removing the Hub:
Removing the Wheel Bearing:
The tool can also be used with a
hydraulic cylinder.
A longer spindle and a hydraulic
hollow piston cylinder are
required for this.
Cylinder 80251000
Pull Spindle 61471400
Universal Spring Hose Clamp Pliers
A single pair of pliers for wire and spring hose clamps of
various sizes up to 70 mm. Adapts to any position by
rotating grip inserts, but also provides a firm hold on the
clamps in the chuck.
•
•
•
•
For spring hose clamps up to 70 mm
Quick-set adjustment: adjusts by shifting directly onto
the workpiece.
Can be used for standard,space-saving and wire
clamps and for spring band rings.
Slim head design; narrow head width, rotatable grip
inserts: an ideal tool, especially in confined areas!
9050340
Universal Spring Hose Clamp Pliers
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 45
Oil Filter Wrench with Ratchet PSA DW-engines
Easy and time-saving removal and installing the oil filter housing of PSA DW engines, which is otherwise
very difficult to reach.
Spanner size: 27
Drive: hexagon





Because of the ratchet mechanism it’s not required that the spanner be
removed and refitted after each turn.
Very sturdy construction.
Developed specifically for these vehicles.
Cut to measure for the constricted position.
Allows professional, torque controlled installation.
Suited for:
DW 10C:
Peugeot 308 2.0 HDi 163CV (from ‘11)
Peugeot 3008 2.0 16v HDi 163CV (from 07- ‘09)
Peugeot 5008 2.0 HDi 163CV (from 12- ‘09)
Peugeot 407 2.0 HDi 163 CV (11-‘10)
Peugeot 407 Coupé 2.0 HDi 163 CV (12-‘09)
Peugeot 508 2.0 HDi 163CV (from 10-’10)
Peugeot RCZ 2.0 HDi (from 04-‘10)
Citroën C4 Picasso 2.0 HDi 16v 163CV automatic (from 09-’10)
Citroën C5 2.0 16v HDi (from ‘10)
Citroën C8 2.0 HDi (from ‘10)
Citroën DS4 2.0 HDi (from ‘11)
Citroën DS5 2.0 HDi (from ‘11)
Ford Mondeo Mk3 2.0 TDCi 163 CV (from ‘10)
Ford C-Max 2.0 TDCi 163CV (from ‘10)
Ford Galaxy Mk3 2.0 TDCi 163 CV (from ‘10)
Ford S-Max 2.0 TDCi 163 CV (from ‘10)
Ford Kuga 2.0 TDCi (from ‘10)
DW 12C:
Citroën C5 Mk2 2.2 HDi (from 10-’10)
Peugeot 508 2.2 HDi GT (from 10-’10)
Ford Mondeo Mk3 2.2 TDCi (from 12-’10)
Ford Galaxy Mk2 2.2 TDCi (from ‘10)
Ford S-Max 2.2 TDCi (from ‘10)
Jaguar XF 2.2D Sportbrake (from ‘12)
61207650
Oil Filter Wrench with Ratchet PSA DW-engines
With ratchet mechanism
Ratschenfunktion
reversible
Optimal shape for the hard
to reach oil filter housing
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 46
Socket for the Exterior Mirror Housing OM






Extra long
Developed specifically for Opel / Vauxhall
T-profile 220 mm long x 3/8" □ drive.
This socket allows, after removing the mirror cover, to
operate the mounting screw of the housing on the door
frame, which is situated down a deep hole.
Time-saving.
Professional, damage-free removal and installation of
the mirror.
Suited for: Opel / Vauxhall Meriva
65463300
Socket for the Exterior Mirror Housing OM
Air Conditioning Lines Repair Kits




Aluminium design eliminates bi-metal reactions to A/C refrigerant.
Viton rubber seals keep refrigerant inside.
Wedge & lock design effectively locks the line into place mechanically
for a permanent repair
Fits SAE and metric lines
Repair Set 1
Repair Set 2
Repair Set 1 + 2
Sizes: 5/8" and 3/4"
Sizes: 5/16", 3/8" and 1/2"
Sizes: 5/8", 3/4", 5/16",
3/8" and 1/2"
9495103
9495104
9495105
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 47
Push Out Kit for the Aluminium 4 Link Front Axle
First the hex head is drilled led by the drill sleeve. Afterwards the
hex head is removed with the special drill without drill sleeve and
the remains of the bolt is drilled to the size of the punch. The
punch pushes now in the centre of the bolt within the suspension
arm. This way the bolt end is not compressed (expanded), which
otherwise often prevents pushing it out of the aluminium body.
•
•
•
To complement present removal tools.
Precisely centred drilling out the 4 Link aluminium steering
knuckle pinch bolt.
Punch Vibro Impact 6180155 is included in the set.
Suited for: VW, Audi, Seat & Škoda
61340075
Push Out Kit for the Aluminium 4 Link Front Axle
Push Out Kit for the Cast Iron 4 Link Front Axle
For precisely centred drilling the 4 link cast iron steering knuckle
pinch bolt. The punch pushes now in the centre of the bolt within
steering knuckle. This way the bolt end is not compressed
(expanded).
•
•
•
To complement present removal tools
Precisely centred drilling out the 4 Link clamping bolt.
Punch Vibro Impact 6180155 is included in the set.
Suited for: VW, Audi, Seat & Škoda
61340025
Push Out Kit for the Cast Iron 4 Link Front Axle
T: +44 1335 368010 • M: +44 7885 244338
1/2
NEWS 2013 47
Punch Vibro Impact
•
•
•
Easy and safe handling
Simple, time-saving disassembling
Universally applicable, e.g. steering knuckle pinch bolt VAG
The Air Hammer Vibro Impact produces strong impact blows at a high frequency.
This impact blow is transmitted through the punch directly to the steering knuckle
pinch bolt. The transmitted vibration solves the corroded connection and push
bolt through the housing.
To actuate an air impact hammer is required e.g. 80257001 Air Hammer Vibro Impact
Length: 115 mm
Diameter: 6.5 mm
Overall length: 190 mm
Weight: 115 g
6180155
Punch Vibro Impact
Steering Knuckle Pinch Bolt Removal Tool
•
•
•
•
For safe and time-saving pushing out of the steering knuckle
pinch bolt.
Maximum internal height 120 mm
The steering knuckle pinch bolt is pressed flush with the flat
pressure pad and then out with the punch.
Actuation with hydraulic spindle 12 tons 10416500.
Suited for: Aluminium and steel 4 link suspension
Audi A4 and A6, VW Passat and Seat Exeo
61746850
Steering Knuckle Pinch Bolt Removal Tool
T: +44 1335 368010 • M: +44 7885 244338
2/2
NEWS 2013 48
Engine Support Bar - Model OM Basis Opel ll
•
•
•
•
•
•
•
•
•
•
Loading capacity: 800 kg
Length:1650 mm
Multiple adjustable feet
Rubber foot rests
Adjustable spider
Time-saving, trouble-free assembly
and disassembly by hand
Affordably expandable
Continuous raising and lowering
Flexibly adjustable
Secure hold
60806625
Engine Support Bar Model OM Basis Opel II – complete
with bar, support adapter and hook set (1 - 4)
60806620
Engine Support Bar Model OM Basis Opel II - complement without
bar, support adapter and hook set (1)
1
60806620 Engine Support Bar
model OM basis Opel II - complement
2
60808400 Hook set (three pieces)
3
60808100 Support adapter including three hooks
4
60808650 Support Bar
1
Optional
Contents:
5
60806760 Pair of Legs front/back, right/left
(necessary for Opel Astra J)
6
60806613 Pair of Legs front/back, right/left
(necessary for Opel Insignia)
7
60806710 Pair of Legs front/back, left/right
(necessary for Opel Meriva B)
5
2
3
4
T: +44 1335 368010 • M: +44 7885 244338
6
7
1/1
NEWS 2013 49
Exclusive Trolley XL
Secure and compact storage of small and large tools thanks to seven lockable and
100% extractable drawers and an 85 litre large top compartment.
Width:
Height:
Depth:
•
•
•
•
•
•
•
800 mm
1030 mm
500 mm
50 cm
Seven lockable drawers, 100% extractable
Large top compartment (85 litres, 160 mm deep, lockable)
Lid with gas pressure springs
Massive handle for shunting
Ball bearing wheels with rubber tread and roller brake
Warp resistant because of the heavy duty safety edges
Extremely stable and steady
8500008
103 cm
Exclusive Trolley XL
80 cm
Centralised drawer locking
Optimal accessory:
Magnetic tray for trollies
The shelf made of powder-coated sheet steel can
be attached to metallic surfaces such as tool
boxes, trollies, lifting platforms, peg boards, etc.
8500090
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 50
Universal Glow Plug Sealing Seat Reamer Set
Universal reamer set for different types of engines.
To clean glow plug holes and especially the sealing
seat in the cylinder head.
Supplied in a case including reamers for the
following screw-in threads and sealing seat angles:
M8x1
90° sealing seat angle
6041625
M8x1
60416225
M9x1
60416215
M10x1
6041725
M10x1
60417025
M10x1.25
60417225
M10x1.25
60417029
M12x1.25
6041615
Supplied in a case with six reamers, two actuator thumb wheels, five screw-in guides,
seven tube brushes (Ø 4.7 mm - 11 mm) and an angle gauge.
60417300
UNI Glow Plugs Sealing Seat Reamer Set
Set of Cleaning Brushes
To clean glow plug holes and to prepare for the
use of reamers.
•
•
•
•
14 pieces
Brush made of steel and brass wire
Ø 4.7 mm - 11 mm
Two brushes for each size
Tube brush Ø4.7 mm, steel wire
6049024
6049025
6049026
6049027
6049029
6049031
Tube brush Ø4/Ø6/Ø9 mm shouldered, brass wire
9049026
90490300
Glow Plugs Hole Cleaner Brush Set 14 pcs, Steel and Brass Brushes
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 51
Battery Booster Pack
12V/14Ah and 12V/22Ah
•
•
•
•
•
•
Battery type: sealed, leak-free lead-acid battery with solid
electrolytes (MPA), in accordance with IATA safety standards
Automatic battery charger with an intelligent charging circuit which
can remain on constantly without causing damage
12V power output (cigarette lighter socket) equipped with
a 20A circuit breaker; can be used as a power source for other
12V devices
Fully isolated terminals and robust flexible copper cables
Protected against voltage spikes
Button with LEDs to control the state of charge (25% to 100%)
9404010
25 cm
20 cm
1
9404010
Battery Booster Pack cars 12V
14Ah starting capability 250A/peak power 1400 A
28 cm
9404000
Battery Booster Pack cars/SUV-s 12V
22Ah starting capability 700A/peak power 2200 A
31 cm
2
9404000
Comparision of technical data:
1
9404010
2
9404000
Voltage:
12 V
12 V
Peak power:
1400 A
2200 A
Capacity:
12 V 14 Ah
12 V 22 Ah
Starting capability:
250 A
700 A
Charge:
230 V
230 V
Recharge:
12 V 0.6 Ah
12 V 1.5 Ah
Cable diameter:
25 mm2
25 mm2
Cable length:
64 cm
64 cm
Weight (kg):
5.8 kg
8.6 kg
T: +44 1335 368010 • M: +44 7885 244338
1/1
NEWS 2013 52
Start & Stop Battery Analyzer
•
•
•
•
•
•
•
Checks 6 to 12V batteries and 12 to 24V charging systems
Built-in printer
Digital screen
Operating range: 40 ~ 2000 CCA
Checks EHL, VRLA/GEL, AGM and SLI batteries in two seconds
Rating system: SAE (CCA)/DIN/EN/IEC and JIS
Available in six languages
9204012
Start &Stop Battery Analyzer
Bushings Tool – Ford, Mazda and Volvo
With this tool, the bushings can easily be replaced directly on the vehicle,
without having to remove or replace the entire rear suspension arms.
Suited for:
Ford Focus ꞌ98 – ꞌ04, Focus II from ꞌ04, C-Max ꞌ03 – ꞌ07, Kuga from ꞌ08
Mazda 3 from ꞌ03, 5 from ꞌ05
Volvo C 30 from ꞌ06, S 40 II from ꞌ04, V 50 from ꞌ04
1
2
Contents: 1 Support sleeve (assembly)
2 Press-out sleeve (disassembly)
3 Spacer ring
4 Insert ring with press-in stop (assembly)
3
5 Insert ring for the basic unit U14 (disassembly)
61766625
Bushings Tool – Ford, Mazda and Volvo
Complement:
4
5
For use, one of the following basic units is needed:
61491050
Basic Unit U14S including
adapter, 12 ton hydraulic spindle,
insert ring and safety cable
61491100
Basic Unit U14S including pull and pressure
spindle, 12 ton hollow piston cylinder, insert
ring and safety cable
T: +44 1335 368010 • M: +44 7885 244338
1/1
2013
NEW PRODUCTS
53
Universal Engine and Gearbox Support
• universally usable
• practical operation by
one person
• simple supporting thanks
to the scissor jack
• extendable spindles
An user-friendly universal
engine and gearbox support,
which is not a base unit with
adapters, but one unit with
scissor jack.
61136500
max. carrying capacity:
250 kg
tot. length:
1050 mm
tot. height:
100 mm
max. lifting height of the
scissor jack:
260 mm
weight:
10 kg
Universal Engine and Gearbox Support
Premium crossbar
for the Universal Engine and Gearbox Support
• larger and more flexible spans
through extension arms
• independently of each other
swiveling arms
max. 1270 mm
min. 210 mm
61135510
• stronger spindles in two
different lengths with hex
drive(245mm und 495 mm)
• large support buffer for a
larger bearing area to protect
the underbody
Premium crossbar for the Universal Engine and Gearbox Support
www.pichler-werkzeug.com · www.pichler-tools.com · www.pichler-outillage.com · www.pichler-werktuig.com
2013
PRODUCT NEWS
54
Suction and Filler Pump 200 ml
Handy pump for controlled extraction and filling of liquids
removable cap allows filling
and cleaning of the pump body
transparent pump body and exact
scale allow optimal dosing
transparent, flexible hose
• transparent pump body with
easily readable scale
• 180 mm long, flexible hose
Ideal for work where small quantities of liquids must be removed
or filled accurately dosed , e.g.
brake fluid and differential gear
oil.
Universally usable for e.g. cooling
fluid, mineral and synthetic oils,
etc..
Volume:
Hose length:
Hose-Ø:
90118600
200 ml
180 mm
8 mm
For controlled extraction and filling of liquids.
removable cap allows filling
and cleaning of the pump body
• transparent pump body with
easily readable scale
• 380 mm long, flexible hose
• with shut-off valve
transparent pump body and exact
scale allow optimal dosing
aluminum tip with cap
with shut-off valve
90118500
transparent,
flexible hose
The transparent pump body and
the easy to read scale allows precise dosing. Universally usable
for heating oil, mineral, synthetic
and biological oil, fuel, cooling
fluid, antifreeze, petroleum and
brake fluid.
Volume:
1500 ml
Hose length:
380 mm
Hose-Ø:
17 mm
2013
55
NEW PRODUCTS
ABS sensor reamer
For cleaning the bore for the ABS sensor in the wheel bearing housing.
• time saving
• no damage to the new sensor
during mounting
• ensure accurate readings
• with ratchet
• for VAG cars
Perfect removing rust, dirt
and corrosion from the bore
for the ABS sensor in the
wheel bearing housing.
Because of the flex joint pivot
can the integrated fine tooth
ratchet be adjusted to the
mounting position.
Length:
45 mm
Diameter:
11 mm
Suited for
AUDI:
A3 (8P), Q3 (Modell 8U), TT (8J)
VW:
Beetle from ’11, Golf V / Plus / Variant, Golf VI / Cabrio / Variant, Jetta
III, Jetta IV, Passat (3C) / CC / Variant, Scirocco from ’09, Sharan from
’10, Tiguan (5N), Touran from ’05
SEAT:
Altea + XL, Leon, Toledo III
ŠKODA:
Octavia (1Z.), SuperB (3T.)
and Yeti from ’10
61310425
ABS sensor reamer
2013
56
NEW PRODUCTS
Gearbox Bearing Race Remover
For the quick and safe removal of the bearing race from the gearbox housing.
• straight, controlled pulling out
the bearing race
• uniform load distribution - this
avoiding cracks in the housing
Suited for
M32, MT20-6, M32-6 and F40
(big, conical bearing race of
the gearbox)
OPEL:
Astra H/J, Corsa D, Meriva A/B,
Signum, Vectra C and Zafira B
FIAT:
Punto 1,9l JTD (from ’99)
ALFA ROMEO:
159 2,0l JTDM (from ’09)
61026050
Gearbox Bearing Race Remover
2013
57
NEW PRODUCTS
Suspension Bush Tool
For replacing the bushings in the rear supporting arm in various versions.
• the work is done directly on
the vehicle with a minimal of
dismounting parts
4
3
• 20 minutes working time
per side
1
Optimized for use with hydraulic
components from Pichler Tools
e.g.:
7
20 ton Hydraulic Spindle
80251270
2
5
17 ton Hydraulic Spindle with
Adapters
80251250 & 6149141L
6
The tool set 91766600 has the
same advantages and features
as 91766500 , but is optimized
for use with hydraulic components from Wallmek e.g.:
examples of use
90251230
90251250
90251260
1
91491070
2x
Support Rod for the Basic Device
2
91491061
1x
Bottom Jaw Plate for the
Basic Device
3
91491066
4x
Flange Nuts M18
4
61491020
1x
Top Plate with Tread for the Basic
Device U14
5
91766602
1x
Suspension Bush Tool Press plate
6
91766603
1x
7
91766601
1x
91766500
Suspension Bush Tool Support
C-Ring
Suspension Bush Tool Press
Sleeve
91766550
Suspension Bush Tool Complementary Kit with Base Unit U14 present
91766500
Suspension Bush Tool Kit with U14 Basic Device (Pichler)
91766600
Suspension Bush Tool Kit Wallmek
Suited for
91766550
Volvo S60, S80(L), V60, V70,
XC60, XC70
Ford Mondeo, S-Max, Galaxy
2013
58
NEW PRODUCTS
Suspension Bush Tool VW T5
For replacing the rear bush in the supension arms of a VW T5.
3
1
2
5
4
• quick replacement of the bush
• the work is done directly on
the vehicle
removing
The tool can be used with the
following hydraulic cylinders:
90251250
installation
1
Press Sleeve
91749401
2
Press Pipe
91749402
3
Adapter M22-M14
9147113
4
Pulling Rod M14 250 mm
9147124
5
Flange Nut M14
9147114
91749400
Suited for
90251260
VW T5
Suspension Bush Tool VW T5 for replacing the rear bush in the front axle supension arms VW T5
2013
XX
59
NEW PRODUCTS
Pressure Piece Set for the Pendulum Support
Bearings in the Subframe VAG, 3 pcs.
Pressure Piece Set for replacing the vibration damper (rubber bushings) of the pendulum
support in the aluminum subframe on the workshop press.
removing
installation
• for use with the workshop press
Suited for
• quick and simple replacement
VW:
Caddy III (2004-2010), Eos (2006-),
Golf V (2003-2009), VI (2008-),
Scirocco (2005-), Jetta III (20052010), Passat (2005-2010), Tiguan
(2007-), Touran (2003-)
SEAT:
Altea (2004-), Leon (2005-),
Toledo (2004-2009)
ŠKODA: Octavia (2004-2010)
AUDI: A3 (2005), TT (2006-2010)
and others
91756900
Pressure Piece Set for pendulum support bearings in the subframe VAG, 3 pcs.

NEWS 2013 01 Seat Cover Puller Bracket Set for

Transcription

Similar documents

Event Poster

Devour - Roto Grip

Quality and Maintenance – Secrets to Success

“A cut above the rest!”

AVS24 2.4 GHZ Wireless Audio/Video Sender

1" Impact Wrench - Racine Railroad

HEMINEVRIN - Alcohol and Alcoholism

No trophy could ever fully express our

Chaise Lounge

Broadband users: the PDF