77-107 Combined Manual - East

Transcription

77/107 DRILLS
107 DRILL - S.N. CJ 4427 & UP
77 DRILL - S.N. CJ 50177 & UP
Operating Instructions
and Parts Reference
PO BOX 1940, JAMESTOWN, ND 58402-1940
DECEMBER 2005
0500117
A Tradition of Innovation Since 1966
77/107 DRILLS
107 DRILL - S.N. CJ 4427 & UP
77 DRILL - S.N. CJ 50177 & UP
Operating Instructions
and Parts Reference
DuraTech Industries International Inc. (DuraTech Industries) has made every effort to assure that
this manual completely and accurately describes the operation and maintenance of the 77/107
DRILL™ as of the date of publication. DuraTech Industries reserves the right to make updates to
the machine from time to time. Even in the event of such updates, you should still find this manual
to be appropriate for the safe operation and maintenance of your unit.
This manual, as well as materials provided by component suppliers to DuraTech Industries are all
considered to be part of the information package. Every operator is required to read and understand
these manuals, and they should be located within easy access for periodic review.
and
are registered trademarks of Duratech Industries
International, Inc. 77 DRILL and 107 DRILL are trademarks of Duratech Industries International,
Inc.
Foreword
All personnel must read and understand before operating unit
• Foreword and Section 1, important safety information.
• Section 2, ”Dealer Preparation,” to verify that the machine has been prepared
for use.
• Section 3, “Introduction,” which explain normal operation of the machine.
• Section 4.1, “Operating Instructions” Pre-Operation Inspection Check List.
Appropriate use of the unit
The 77/107 Grain Drill is designed to seed No-Till, Minimum Till, or conventionally
tilled fields. The two compartment hopper offers the flexibility of seeding with
fertilizer, seeding alone, or planting two different seeds.
Operator protection
As with all machinery, care needs to be taken by the operator in order to insure the
safety of the operator and those in the surrounding area.
WARNING: Operators and those observing the operation of the 77/107
GRAIN DRILLS are required to wear head, eye, and ear protection. No loose
clothing is allowed.
77/107
DRILLS
O P E R AT I N G I N S T R U C T I O N S
i
TABLE
OF
CONTENTS
Part 1: Operating Instructions ...........................................
Introduction ................................................................................ 2
Purpose ....................................................................................... 2
Section 1: Safety ....................................................................... 3
1.1
1.2
1.3
1.4
1.5
1.6
Safety-Alert Symbols ........................................................................................ 3
Operator - Personal Equipment ........................................................................ 5
Machine Safety Labels ..................................................................................... 6
Shielding ............................................................................................................ 8
Personal Equipment .......................................................................................... 8
Safety Review ................................................................................................... 8
Section 2: Dealer Preparation ................................................. 12
2.1 Gauge Wheel Attachment ............................................................................... 12
2.2 False Bottom Attachment (107 Only) ............................................................. 14
2.3 Drill Legume Box Attachment ........................................................................ 16
2.4 Legume Hopper Shipping Kit (Optional) .......................................................... 18
Section 3: Introduction ............................................................ 19
3.1 Ordering Parts .................................................................................................. 19
3.2 Serial Number Decal ........................................................................................ 20
3.3 About your 77/107 Grain Drill .......................................................................... 20
Section 4: Operating Instructions ........................................... 21
4.1 Operating Instructions ...................................................................................... 21
4.2 Grain Drill Setup ............................................................................................... 22
4.3 Pressure Spring Adjustment ............................................................................. 22
4.4 Press Wheel Adjustment .................................................................................. 23
4.5 Haybuster 77/107 Drill Opener ........................................................................ 24
4.6 Feed Wheel Space Adjustment ........................................................................ 25
4.7 100 Drill Cleanout Slides .................................................................................. 26
4.8 Calibration Pointer Adjustment ......................................................................... 27
4.9 Setting And Checking Feed Rate .................................................................... 28
4.10 Checking Feed Rate ...................................................................................... 29
4.11 Drilling With The Grain Drill ........................................................................... 34
4.12 Suggestions .................................................................................................... 36
4.13 Rear Wheel Swivel And Ajustment ................................................................ 36
4.14 Transporting The Grain Drill ........................................................................... 36
4.16 Preparing For Storage .................................................................................... 38
4.17 Removing From Storage ................................................................................. 38
Section 5: Lubrication .............................................................. 39
APPENDIX A: WARRANTY ....................................................... 42
APPENDIX B: SPECIFICATIONS .............................................. 43
ii
77/107
DRILLS
TABLE
OF
CONTENTS
Part 2: Parts Reference .................................................. 45
77 MAIN FRAME ASSEMBLY ........................................................................... 46
107 MAIN FRAME ASSEMBLY ......................................................................... 48
77 DRIVE ASSEMBLY ........................................................................................ 52
77 DRIVE WHEEL ASSEMBLY ......................................................................... 54
107 DRIVE ASSEMBLY ...................................................................................... 56
TANK END DRIVE (77 & 107) .......................................................................... 58
RUN ASSEMBLY (77 & 107) .............................................................................. 60
77 TANK ASSEMBLY (DETAIL A) .................................................................... 62
77 TANK ASSEMBLY (DETAIL B) .................................................................... 64
77 TANK ASSEMBLY - BACK ........................................................................... 66
107 TANK ASSEMBLY ........................................................................................ 68
SEED & FERTILIZER SETTING ASSEMBLY .................................................. 70
SCRAPER ASSEMBLY ....................................................................................... 71
COULTER & DISK ASSEMBLY ........................................................................ 72
PRESS WHEEL ASSEMBLY ............................................................................... 73
HUB ASSEMBLY ................................................................................................. 74
HUB FORK ASSEMBLY ..................................................................................... 76
FRONT STABILIZER OPTION (107 ONLY) .................................................... 77
REAR STABILIZER OPTION (107 ONLY) ....................................................... 78
TOW HITCH (107 ONLY) ................................................................................... 80
BALLAST BRACKET (77 & 107) ...................................................................... 81
HITCH LIFT (107 ONLY) .................................................................................... 82
DRILL SINGLE HITCH (77 & 107) .................................................................... 84
2 DRILL HITCH (107 ONLY) .............................................................................. 86
3-4 DRILL HITCH (107 ONLY) .......................................................................... 88
SINGLE DRILL & 2 DRILL HYDRAULICS ..................................................... 89
3 DRILL HYDRAULICS (107 ONLY) ................................................................ 90
4 DRILL HYDRAULICS (107 ONLY) ................................................................ 91
DECALS ................................................................................................................ 92
DECAL LOCATIONS .......................................................................................... 95
77 LEGUME BOX OPTION ................................................................................ 96
107 LEGUME BOX OPTION .............................................................................. 98
SEED INDEX ASSEMBLY LEGUME BOX (DETAIL C) .............................. 100
CUP ASSEMBLY LEGUME BOX (DETAIL D) .............................................. 101
LEGUME DROP TUBE ASSEMBLY ............................................................... 102
LEGUME BOX MOUNTING BRACKET (77 & 107) ..................................... 104
ACRE COUNTER (OPTION) (77 & 107) ........................................................ 105
FALSE BOTTOM OPTION (107 ONLY) ......................................................... 106
77 NATIVE GRASS KIT OPTION - ADDITIONAL AGITATOR SHAFTS .. 108
77/107
DRILLS
iii
TABLE
OF
CONTENTS
107 NATIVE GRASS KIT - ADDITIONAL AGITATOR SHAFTS ................. 110
107 NATIVE GRASS KIT - TANK, EXISTING SHAFT MODIFICATIONS . 112
NATIVE GRASS KIT - TANK END DRIVE ASSEMBLY (77 & 107) ........... 114
NATIVE GRASS KIT - SEED AND FERTILIZER
SETTING ASSEMBLY (77 & 107) .................................................................... 116
NATIVE GRASS KIT - DROP TUBE AND HOSE (77 & 107) .................... 117
GAUGE WHEELS OPTION (77 & 107) ........................................................... 118
DRILL LIGHT KIT OPTION (77 & 107) .......................................................... 120
77 / 107 DRILL Documentation Comment Form ................... 123
iv
77/107
DRILLS
77/107 DRILLS
107 DRILL - S.N. CJ 4427 & UP
77 DRILL - S.N. CJ 50177 & UP
PART 1: Operating
Instructions
1
77/107
DRILLS
1
Introduction
The 77/107 Grain Drills are designed to seed No-Till, Minimum Till, or conventionally tilled fields. Two 30 gallon tanks
are available for added ballast to penetrate the tough no-till conditions.
The two compartment hopper offers the flexibility of seeding with fertilizer, seeding alone, or planting two different
seeds. The metering system for each hopper is infinitely adjustable.
Field hitches are available for one or multiples of two, three, and four of the model 107 Drill only. A tow hitch is also
available for the 107 Drill to allow the towing of two or more drills in transport.
Purpose
The purpose of this owner’s manual is to explain maintenance requirements and routine adjustments for the most
efficient operation of your 77/107 Grain Drill. There is also a trouble shooting section that may help in case of problems
in the field. Any information not covered in this manual may be obtained from your dealer.
Special Note: When reference is made as to front, rear, right hand or left hand of this machine, the
reference is always made from standing at the rear end of the machine and looking towards the hitch.
Always use serial number and model number when referring to parts or problems. Please obtain your
serial number and write it below for your future reference.
MODEL:
2
77/107
77 DRILL
107 DRILL
DRILLS
SERIAL NO.
________________________
Section 1: Safety
The safety of the operator is of great importance to DuraTech Industries/Haybuster. We have provided decals, shielding
and other safety features to aid you in using your machine safely. In addition, we ask you to be a careful operator who
will properly use and service your Haybuster equipment.
WARNING: FAILURE TO COMPLY WITH SAFETY INSTRUCTIONS THAT FOLLOW
WITHIN THIS MANUAL COULD RESULT IN SEVERE PERSONAL INJURY OR DEATH.
BEFORE ATTEMPTING TO OPERATE THIS MACHINE, CAREFULLY READ ALL
INSTRUCTIONS CONTAINED WITHIN THIS MANUAL. ALSO READ THE INSTRUCTION
MANUAL PROVIDED WITH YOUR TRACTOR.
THIS MACHINE IS NOT TO BE USED FOR ANY PURPOSE OTHER THAN THOSE
EXPLAINED IN THE OPERATOR’S MANUAL, ADVERTISING LITERATURE OR OTHER
DURATECH INDUSTRIES WRITTEN MATERIAL PERTAINING TO THE 77/107 GRAIN
DRILL.
1.1 Safety-alert symbols
Decals are illustrated in Part 2: Parts Reference.
The safety decals located on your machine contain important and useful information that will help you operate your
equipment safely.
To assure that all decals remain in place and in good condition, follow the instructions below:
•
Keep decals clean. Use soap and water - not mineral spirits, adhesive cleaners and other similar cleaners
that will damage the decal.
•
Replace all damaged or missing decals. When attaching decals, surface temperature of the machine must
be at least 40° F (5° C). The surface must be also be clean and dry.
•
When replacing a machine component to which a decal is attached, be sure to also replace the decal.
77/107
DRILLS
3
DuraTech Industries uses industry accepted ANSI standards in labeling its products for safety and operational
characteristics.
Saf
ety-Aler
Safety-Aler
ety-Alertt Symbol
Read and recognize safety information. Be alert to
the potential for personal injury when you see this
safety-alert symbol.
DANGER: Indicates an imminently
hazardous situation that, if not avoided, will
result in death or serious injury. This signal
word is to be limited to the most extreme
situations, typically for machine components
that, for functional purposes, cannot be
guarded.
WARNING: Indicates a potentially
hazardous situation that, if not avoided, could
result in death or serious injury, and includes
hazards that are exposed when guards are
removed. It may also be used to alert against
unsafe practices.
CAUTION: Indicates a potentially hazardous
situation that, if not avoided, may result in
minor or moderate injury. It may also be used
to alert against unsafe practices.
This manual uses the symbols to the right to denote
important safety instructions and information.
The DANGER, WARNING and CAUTION symbols are
used to denote conditions as stated in the text above.
Furthermore, the text dealing with these situations is
surrounded by a box with a white background, will begin
with DANGER, WARNING, or CAUTION.
The INFORMATION symbol is used to denote important
information or notes in regards to maintenance and use of
the machine. The text for this information is surrounded
by a box with a light grey background, and will begin with
either Important or Note.
4
77/107
DRILLS
DANGER
WARNING
CAUTION
INFORMATION
1.2 Operator - personal equipment
THE OPERATOR
Physical Condition
You must be in good physical condition and mental health and not under the influence of any substance (drugs, alcohol)
which might impair vision, dexterity or judgment.
Do not operate a 77/107 DRILL when you are fatigued. Be alert - If you get tired while operating your 77/107
DRILL, take a break. Fatigue may result in loss of control. Working with any farm equipment can be strenuous. If
you have any condition that might be aggravated by strenuous work, check with your doctor before operating
Proper Clothing
Clothing must be sturdy and snug-fitting, but allow complete freedom of movement.
Avoid loosefitting jackets, scarfs, neckties, jewelry, flared or cuffed pants, unconfined
long hair or anything that could become entangled with the machine.
Protect your hands with gloves when handling discs and coulters. Heavy duty, nonslip
gloves improve your grip and protect your hands.
Good footing is most important. Wear sturdy boots with nonslip soles. Steel-toed safety
boots are recommended.
To reduce the risk of injury to your eyes never operate a 77/107 DRILL unless wearing
goggles or properly fitted safety glasses with adequate top and side protection.
Tractor noise may damage your hearing. Always wear sound barriers (ear plugs or ear
mufflers) to protect your hearing. Continual and regular users should have their hearing
checked regularly.
77/107
DRILLS
5
1.3
Machine safety labels
The safety decals located on your machine contain important information that will help you operate your equipment.
Become familiar with the decals and their locations.
WARNING: FOR YOUR PROTECTION AND
PROTECTION OF OTHERS, PRACTICE THE
FOLLOWING SAFETY RULES.
1.
BEFORE OPERATING THIS MACHINE, READ THE
OPERATOR’S MANUALS SUPPLIED WITH THIS
MACHINE AND YOUR TRACTOR.
2.
CHECK OPERATORS MANUALS TO BE SURE
YOUR TRACTOR MEETS THE MINIMUM
REQUIREMENTS FOR THIS MACHINE.
3.
READ ALL DECALS PLACED ON THIS MACHINE
FOR YOUR SAFETY AND CONVENIENCE.
4.
NEVER ALLOW RIDERS ON THIS IMPLEMENT OR
THE TRACTOR.
5.
KEEP OTHERS AWAY FROM THIS MACHINE
WHILE IN OPERATION.
6.
KEEP ALL SHIELDS IN PLACE WHILE MACHINE IS
OPERATING.
7.
KEEP HANDS, FEET, LOOSE CLOTHING, ETC.,
AWAY FROM POWER DRIVEN PARTS.
8.
ALWAYS SHUT OFF MACHINE AND ENGINE
BEFORE SERVICING, UNCLOGGING,
INSPECTING, OR WORKING NEAR THIS MACHINE
FOR ANY REASON. ALWAYS PLACE
TRANSMISSION IN PARK OR SET PARK BRAKE
AND WAIT FOR ALL MOVEMENT TO STOP
BEFORE APPROACHING THIS MACHINE.
WARNING: FOR YOUR PROTECTION KEEP ALL
SHIELDS IN PLACE AND SECURED WHILE MACHINE
IS OPERATING MOVING PARTS WITHIN CAN CAUSE
SEVERE PERSONAL INJURY.
6
77/107
DRILLS
WARNING: CHEMICALS MAY CAUSE EYE, SKIN AND
BREATHING PROBLEMS.
WEAR FACE MASK, GLOVES AND GOGGLES .
READ AND FOLLOW SAFETY INSTRUCTIONS ON THE
CHEMICAL SUPPLIERS LABEL.
WARNING: NO RIDERS.
SERIOUS PERSONAL INJURY COULD RESULT FROM
RIDING ON STEP.
WARNING: DISC BLADES ARE EXTREMELY SHARP!
WEAR HEAVY GLOVES WHEN SERVICING.
CAUTION: KEEP WHEEL BOLTS TIGHT.
77/107
DRILLS
7
•
1.4
Replacement decals can be purchased from your Haybuster dealer.
Shielding
Shields are installed for your protection. Keep them in place, and replace damaged shields.
1.5 Personal equipment
Operators of this machine are encouraged to wear head, eye, and ear protection. Loose clothing is discouraged.
1.6 Safety review
BEFORE OPERATING
•
Read and follow all instructions contained in:
A.
This 77/107 DRILL Operator’s Manual.
B.
Tractor operator’s manual.
C.
Decals placed on the 77/107 Drill and Tractor.
NOTE: Additional copies of the above mentioned materials can be obtained from your dealer.
8
•
Be sure all safety shields and covers are securely in place when machine is running.
•
Read all warning and instructional decals placed on the machine for your safety and convenience.
•
Allow only responsible, properly instructed individuals to operate machine. Carefully supervise
inexperience operators.
•
Make no modifications to this equipment unless specifically requested or recommended by DuraTech
Industries.
•
Tighten or replace any loose or cracked bolts, chains, hoses or connections.
•
The towing vehicle must be of equal or greater weight than the grain drill for adequate braking capacity.
77/107
DRILLS
DURING OPERATION
•
Exercise extreme caution with operating the drill on steep slopes or grades.
•
Be sure all spectators are clear of the area where the drill is in operation or raised and lowered.
•
Be sure the tractor operator is the only person riding the tractor. Allow no one to ride the drill at any time.
•
Remember, loose clothing, necklaces and similar items are more easily caught in moving parts. Avoid
the use of these items if possible and keep long hair confined.
•
Never work under the drill when the drill is lifted up unless the safety stop bar is in position.
•
Watch out for and avoid any object that might interfere with the proper operation of the machine.
DURING SERVICE & MAINTENANCE
CAUTION: Before performing any maintenance or adjustments make sure machine is NOT
running.
•
Before working on or near drill for any reason including servicing, lubricating, cleaning, inspecting or
refilling, or if working under drill or detaching from tractor, install safety stop bar (next to hydraulic
cylinder).
•
When replacing any part on your drill, be sure to use only DuraTech Industries authorized parts.
•
Relieve all pressure in the hydraulic system before disconnecting the lines or performing other work on
the system. Make sure all connections are tight and the hoses and lines are in good condition before
applying pressure to the system.
CAUTION: Hydraulic fluid escaping under pressure can be invisible and have enough force to
penetrate the skin. When searching for a suspected leak, use a piece of wood or cardboard rather than
your hands. If injured, seek medical attention immediately to prevent serious infection or reaction.
•
Be careful when using a hoist or other lifting device. Use only devices that have adequate lifting capacity
and be sure the chain or cable is securely attached.
77/107
DRILLS
9
WHEN TRANSPORTING ON PUBLIC ROADS
10
•
Use good judgment and drive carefully, especially over rough or uneven roads.
•
Be sure tractor brakes are properly adjusted and foot pedals locked together.
•
Check your state laws regarding the use of lights, slow moving vehicle sign, safety chain and other
possible requirements.
•
Do not tow drills at speeds over 20 mph. It is recommended that drills be empty of seed or fertilizer
when transporting.
77/107
DRILLS
IMPORTANT WINCH SAFETY INFORMATION
•
The winch is built for multipurpose hauling and lifting operations. It is not to be used as a hoist for
lifting, supporting or transporting people, or for loads over areas where people could be present.
•
Respect the winch. High forces are created when using a winch, creating potential safety hazards. It
should be operated and maintained in accordance with instructions. Never allow children or anyone who
is not familiar with the operation of the winch to use it. A winch accident could result in personal injury.
•
Check winch for proper operation on each use. Do not use if damaged. Seek immediate repairs.
•
Never exceed rated capacity. Excess load may cause premature failure and could result in serious
personal injury.
•
Never apply load on winch with cable fully extended. Keep at least three full turns of cable on the reel.
•
Secure load properly. When winching operation is complete, do not depend on winch to support load.
•
Operate with hand power only. This winch should not be operated with a motor of any kind. If the
winch cannot be cranked easily with one hand, it is probably overloaded.
FAILURE TO COMPLY WITH ANY OF THE ABOVE SAFETY INSTRUCTIONS OR
THOSE THAT FOLLOW WITHIN THIS MANUAL MAY RESULT IN SEVERE INJURY
OR DEATH.
THIS DRILL IS NOT TO BE USED FOR ANY PURPOSE OTHER THAN THAT FOR
WHICH IT IS INTENDED AS EXPLAINED IN THE OPERATOR’S MANUAL,
ADVERTISING MATERIALS AND OTHER PERTINENT WRITTEN MATERIAL.
PREPARED BY DURATECH INDUSTRIES.
77/107
DRILLS
11
Section 2: Dealer Preparation
2.1 Gauge Wheel Attachment
The heavy duty gauge wheels mount on the tool bar in front of the drill. The gauge wheels are adjustable to maintain a
uniform planting depth when on side hills.
INSTALLATION
12
Step 1:
Place the gauge wheel mount assembly in front of the second run assembly from either tool bar end.
See the accompanying illustration.
Step 2:
Mount the gauge wheel mount assembly to the tool bar by using two gauge wheel mount straps and
four 5/8” x 6-1/2” hex bolts, lock washer and nuts provided. See accompanying illustration.
Step 3:
Repeat Step 1 and Step 2 for the gauge wheel on the other side of the tool bar.
Step 4:
Lift the tool bar using the drill’s hydraulics and insert both gauge wheels into the bottom of the
gauge wheel mount assemblies. See the accompanying illustration.
Step 5:
If conditions prevent Step 4 from being done, the gauge wheels can be inserted into the front of the
gauge wheel mount assemblies. To do this, remove all four bolt sleeves (two per gauge wheel
mount assembly) by unbolting the four 3/4” x 6” hex bolts, lock washers and nuts and push the
gauge wheels into the mount assemblies. Bolt the bolt sleeves on to the gauge wheel mount
assemblies again.
Step 6:
Adjust the gauge wheels to the desired position by inserting the adjustment handle through the
proper gauge wheel adjustment with the hair pin. This adjustment determines the gauge wheel
77/107
DRILLS
Gauge Wheel (Option) Installation
77/107
DRILLS
13
2.2 False Bottom Attachment (107 Only)
The false bottom attachment allows the use of both tanks, front and back, to be used in combination for seed. This will
enable the seed tanks to last longer before refilling during seeding operation.
INSTALLATION
Step 1:
Remove the divider cover (Item #2) from the grain tank by unbolting and setting the cover aside.
Step 2:
Insert the false bottoms right hand (RH) sheet (Item #3) by holding its handles and pushing the
studs into the existing slots found just below the 6” x 24” openings in the center divider as shown in
the accompanying illustration.
Step 3:
Insert the false bottom LH sheet (Item #4) in the same manner as described in Step 2.
Step 4:
Place the side seal retainer RH (Item #5) on the false bottom RH with the rubber seal (Item #9)
fitting in the crimp space provided between the two parts (See Detail A).
Step 5:
Place the side seal retainer LH (Item #6) on the false bottom LH with the rubber seal (Item #9) as in
Step 4.
Step 6:
Place the upper seals (Items #7 and #8) on their respective false bottoms as shown in the
accompanying illustration.
Step 7:
Position the false bottoms by moving them to the left or right so that l/2” exists between the false
bottoms and the seed tank wall (See Detail A).
Step 8:
Place all flat washer, lock washers and nuts (Items #11, #12 and #13) in their respective locations as
shown in the accompanying illustration.
Step 9:
Tighten only the false bottom nuts to secure the false bottoms to the center divider.
Step 10: Slide the upper seals and the side seal retainers firmly against their respective walls and tighten all
the nuts.
The preceding steps are to be followed in the opposite fashion starting with the last step and proceeding to Step 1 to
bring the drill to its original manner.
14
77/107
DRILLS
False Bottom (Option) Installation
(107 Only)
77/107
DRILLS
15
2.3 Drill Legume Box Attachment
The legume box attachment features fluted-feed cups which are capable of accurately metering small seeds even at
very low rates. The hopper will hold up to 150 lbs. of seed.
INSTALLATION
16
Step 1:
Drill four 7/16” diameter holes in the front (grain) box as shown in Figure 1. Measure these holes
carefully and use a good center punch to mark locations before drilling. Loosely bolt the mounting
bracket to the grain box observing left hand and right hand parts.
Step 2:
Remove the convoluted grain hoses and unbolt the cup assemblies from the grain tank. Replace
with modified cup assemblies provided with the legume box kit. Reattach the convoluted grain
hoses to the cups.
Step 3:
Loosen chains, sprockets and bearings and move countershaft on grain tank. Reinstall existing
bearings, sprockets and chains and install 15 tooth sprocket as shown in Figure 2.
Step 4:
Bolt legume box to grain tank using the four 3/8” x 1” bolts provided. The mounts welded to the
rear of the legume box should go between the mounting brackets installed in Step 1. Tighten all
mounting bolts securely.
Step 5:
Bolt the two bearing standards to the brackets on the legume box using six 5/16 x 3/4” carriage
bolts, flat washers, lock washers and nuts. Align the bearing standards before tightening bolts.
Loosely bolt the bearings to the outside of the bearing standards using the four 5/16”’ x 3/4”
carriage bolts. Install the 29” shaft with the 17 tooth sprocket BETWEEN the bearings as shown in
Figure 2. Install two wooden block chain tightener using 3/8” x 2-1/2” bolts, two flat washers, lock
washer and nuts. Tighten the drive chains.
Step 6:
Cut 5/8” I.D. clear plastic hose to 22” lengths. Eighteen are required. Install hoses on the grain
cups first and then on legume box cups. Dipping the ends in a liquid soap solution (one part soap to
one part water) will ease installation of the hoses.
77/107
DRILLS
Legume Box (Option) Installation
77/107
DRILLS
17
2.4 Legume Hopper Shipping Kit (Optional)
18
ITEM
PART NO.
QTY.
DESCRIPTION
1
8700001
1
BRKT\LEGUME\LH\LEG-BOX
2
8700002
1
BRKT\LEGUME\RH\LEG-BOX
3
8700003
4
STRAP\LEGUMEBOX
4
8700008
1
BRG\BOX\LEGUME\RH
5
8700009
1
BRG\BOX\LEGUME\LH
6
2000002
2
BRG\1" W/LOCK\COLLAR
7
2000703
4
FLGETT\1\2BOLT\PLTD
8
2000016
2
BLK\WD\IDLER
9
10
8700011
1000111
1
1
SHFT\1X29\LEGUMEBOX
SPKT\B\40\17\1\1/4KW\SOFT
11
1000112
2
SPKT\B\40\15\1\1/4KW
12
6200010
3
KEY\SQ\1/4X1
13
1100232
1
CHAIN\40NP\53
14
1100246
1
CHAIN\40NP\79
15
1100224
2
CHAIN\40NP\CL
16
1100225
2
CHAIN\40NP\OL
17
3700129
18
HOSE\PVC\5/8IDX22-1/2\CLR
18
4800098
4
BOLT\HEX\3/8X1-1/4\NC
19
4800156
4
BOLT\HEX\3/8X3
20
4800029
2
BOLT\HEX\3/8X2-1/2
21
4800003
4
BOLT\HEX\3/8X1
22
4900002
14
NUT\HEX\3/8\NC
23
5000019
14
WASH\LOCK\3/8
24
5000001
4
WASH\FLAT\3/8
25
4800153
10
BOLT\CRG\5/16X3/4\NC
26
4900003
10
NUT\HEX\5/16\NC
27
5000022
10
WASH\LOCK\5/16
77/107
DRILLS
Section 3: Introduction
Every effort has been made to ensure that the information contained in this manual is correct at the date of publication;
but, due to continuous improvements, DuraTech Industries reserves the right to make changes in the contents without
notice or obligation.
This manual is shipped with each machine to familiarize the operator with the proper operating, maintenance and
lubrication instructions to insure the best possible performance and service from the machine. Study and understand
these instructions thoroughly before operating the machine. We recommend that this manual be readily available for
reference at all times. Consult your DuraTech Industries dealer if any items in this manual are not understood.
DuraTech reserves the right to make changes in engineering, design and specifications, add improvements, or
discontinue manufacture at any time without notice or obligation.
3.1 Ordering Parts
When ordering parts always specify your model number, serial number, and the number of the parts you wish to order.
IMPORTANT: WHEN REPLACEMENT PARTS ARE NEEDED, USE THE LISTED PART
NUMBERS AND DESCRIPTIONS TO INSURE FAST AND ACCURATE SHIPMENT OF YOUR
ORDER. WHEN ORDERING PARTS ALWAYS SPECIFY UNIT SERIAL NUMBER.
ONLY AUTHORIZED PARTS SHOULD BE USED FOR REPAIR AND/OR
REPLACEMENT.
77/107
DRILLS
19
3.2 Serial Number Decal
The serial number and the machine model number are
stamped on the decal. The model number and serial
number are important when service and/or parts are
required.
3.3 About your 77/107 Grain Drill
The 77/107 Grain Drill is designed to seed No-Till, Minimum Till, or conventionally tilled fields. Two 30 gallon tanks are
available for added ballast to penetrate the tough no-till conditions.
The two compartment hopper offers the flexibility of seeding with fertilizer, seeding alone, or planting two different
seeds. The metering system for each hopper is infinitely adjustable.
Field hitches are available for one or multiples of two, three, and four of the model 107 Drill only. A tow hitch is also
available for the 107 Drill to allow the towing of two or more drills in transport.
20
77/107
DRILLS
Section 4: Operating Instructions
To insure long life and economical operation, we highly recommend the operator of the 77/107 Grain Drill be thoroughly
instructed in the maintenance and operation of the machine. There is no substitute for a sound, preventative
maintenance program and a well-trained operator.
Prior to operating the Grain Drill, we recommend the operator make a visual inspection of the unit. This can be done
as the lubrication is being carried out.
4.1 Operating Instructions
Check the following:

Hydraulic components for leaks or damage.
WARNING: Hydraulic fluid escaping under pressure can be almost invisible and can have
sufficient force to penetrate the skin. When searching for suspected leaks, use a piece of wood or
cardboard rather than your hands.
If injured, seek medical attention immediately to prevent serious infection or reaction.

Lug nuts for tightness.

Condition of tire rims.

Tires for proper air pressure.

Condition of rubber convoluted hoses.

Adjustment of all chains.

Installation and condition of shields.

Installation of Slow Moving Vehicle (SMV) sign, if required.

Condition of decals.
WARNING: Before attempting to operate this machine, refer again to pages 14-17 for important
safety information.
77/107
DRILLS
21
4.2 Grain Drill Setup
The 77/107 Grain Drill may be shipped without the hydraulic lift cylinder, since the grain drill used a standard 3” x 8”
cylinder. The retracted length must be 20-1/4”, measured from the center of the mounting holes. When multiple grain
drills are used, a cylinder will be required for each grain drill.
•
Set the wheels on your tractor out as wide as possible for maximum stability.
•
Hitch the grain drill to the tractor.
•
Connect the hydraulic hoses to the tractor’s hydraulic system.
4.3 Pressure Spring Adjustment
To gain versatility for all types of terrain and soil conditions, it is important to have a considerable amount of up and
down travel built into each individual run. When seeding on level terrain, adjust hydraulic cylinder stroke to lower
Movable Frame so openers penetrate soil approximately two (2) inches and Parallel Bars are about level when viewed
from the side. The toolbar height will be about 20” when discs are new. This will allow runs to move up or down
according to terrain.
If parallel bars are not level, it will be necessary to adjust pressure spring, or press wheel adjustment.
Proper tension of the pressure spring varies with conditions. No-till seeding may require more down pressure; loose
soil requires less. Since the pressure springs work together with the opener depth adjustment controlled by the
hydraulic cylinder, make sure that the opener depth adjustment is set correctly.
pressure spring adjustment
22
77/107
DRILLS
In extremely loose soils such as freshly worked summer fallow, it will be necessary to lessen tension on pressure spring
instead of lessening hydraulic cylinder stroke.
To adjust the pressure springs:
1.
2.
Make sure the movable frame is raised completely
up and the safety stop bar is secured.
Using the adjustment nut on each pressure spring,
adjust the spring to the desired length. See table at
right showing the opener pressure obtained at
various spring lengths. Under no circumstances
should the spring be adjusted to less than 10
inches. This may damage the spring and related
parts and will also void the warranty on these parts.
SPRING
LENGTH
OPENER
PRESSURE
12¼ IN.
135 LBS.
11½ IN.
180 LBS.
11 IN.
205 LBS.
10½ IN.
235 LBS.
10 IN.
300 LBS.
4.4 Press Wheel Adjustment
n addition to firming the soil around the seed, the press wheels serve as gauge wheels for the openers. The relationship
of each press wheel and opener will remain consistent regardless of terrain or soil density. If the seed is too deep,
lower the press wheel. If the seed is too shallow, raise the press wheel.
To adjust the press wheel height:
1.
Remove quick attachment pin.
2.
To lower the press wheel, relocate shim washers from top to bottom. To raise the press wheel, relocate
shim washers from bottom to top.
3.
Install quick attachment.
depth adjustment washer for
serial numbers 401 and up
77/107
DRILLS
23
4.5 Haybuster 77/107 Drill Opener
The 77/107 Drill uses a coulter-disk offset opener. The coulter blade leads the disk by 1-1/2”. Both blades are the
same size and due to the offset, there is some sliding action where the blades contact. This sliding or scissor action
provides excellent residue cutting action at ground level, especially in wet residue. The scissor action causes some wear
into the coulter blade at the point of contact. This wear is normal and the heavier coulter blade is bolted to the bearing
cage to allow easy replacement.
depth adjustment washer for
serial numbers 401 and up
One complete turn changes points A and B (DWG. 1) the amount shown in DWG. 2. It takes 6 turns to bring points A
and B back together.
24
77/107
DRILLS
4.6 Feed Wheel Space Adjustment
Large seeds require more space between feed wheel lugs and tank wall than small seeds to prevent cracking. Small
seeds require less space to provide an even flow. Therefore each seed listed in the feed rate chart, pages 30 to 33,
shows a required wheel space.
feed wheel space
adjustment.
FEED WHEEL SPACE ADJUSTMENT
1.
Remove the feed wheel covers.
2.
Loosen the eight bolts A and B. There are four sets
of bolts for each feed wheel - two on the outer end
of the hopper and six inside the hopper.
3.
Select the proper space gauge using the wheel
space chart.
4.
Install the proper space gauge as shown.
5.
Slide the feed wheel toward the gauge until the
feed wheel lugs, gauge and hopper are pressed
together. Tighten the eight bolts.
6.
Recheck the feed wheel space adjustment.
7.
Install the feed wheel covers.
The feed wheel space adjustment provides the proper
clearance for the type of seed or fertilizer being
used.
77/107
DRILLS
bolt A
bolt B
one set of feed wheel
space adjustment bolts
25
4.7 100 Drill Cleanout Slides
Cleanout slides are provided on both grain and fertilizer
tanks. Handles for opening and closing the slides are
located on the left side of the drill.
figure 4.1
drill cleanout slides.
26
77/107
DRILLS
4.8 Calibration Pointer Adjustment
Grain and fertilizer sliding gates are preadjusted at the factory. In the event any part of the calibrating mechanism is
removed or replaced, it can be recalibrated in this order:
1.
Place both pointer nut and anchor nut in the center of their respective thread.
2.
Insert a short length of 7/16” rod or the shank end of a 7/16” drill bit into the square hole in sliding gate
as shown.(figure 4.1)
3.
Tighten bearing bolts securing calibration screw to end of tank.
4.
Tighten bolts securing anchor nut to sliding gate.
5.
Place scale plate on tank so number 8 is directly in line with top of pointer. This will insure pointer
setting to coincide with chart. Scale plate must be parallel with calibration screw to allow pointer to
operate smoothly along plate.
calibration pointer
adjustment
77/107
DRILLS
27
4.9 SETTING AND CHECKING FEED RATE
general setting for feed
wheel alignment
For most seeding, the feed wheel should be aligned as shown above. Set the pointer on number 8. The center of the
feed wheel should be centered in the opening as viewed from outside of the box.
The rates shown on the charts serve only as a starting point. Due to variations in material size and density the rates
may vary from the chart. The following methods may be used to determine the proper setting for your particular seed
or fertilizer.
Setting and checking feed rate using wheat as an example.
1.
You want to seed wheat at a rate of 95 lbs. per acre on 7” spacing.
2.
Seed rate charts calls for a wheel space of 1/8” (page 30). Pointer set on 8 (see illustration above). The
adjustment should be made before filling grain tank.
3.
Make sure feed wheel cover is in place. Put grain in tank.
4.
Seed far enough so you can visually check grain flowing into seed cups.
The addition of the single agitator to the standard drill box will prevent these seeds from bridging above the feed
wheels. The single agitator may be added to all 77/107 drills.
Alti wildrye
Bromegrass #
Intermediate wheatgrass
Killdeer sideoats #
Pubescent wheatgrass
Streambank wheatgrass
Tall wheatgrass
Western wheatgrass
# Extremely trashy samples may require the double agitator.
28
77/107
DRILLS
4.10 CHECKING FEED RATE
1.
Measure a distance of 415’ on a drill with 7” spacing and mark. Remove one hose from seed hopper on
each drill. Attach a container (cloth or plastic bag) to hopper to collect seed.
2.
Operate drill at intended planting speed through entire length of test track.
3.
Weigh the sample in ounces (less weight of sample container). Use the following formula to determine
lbs./acre for your particular shank spacing.
7” Spacing - oz. x 11.25 = lbs./acre
EXAMPLE
Sample and container weighs
Container weighs
Weight of sample only
9.9 ounces
- 1.5 ounces
8.4 ounces
4.
Use formula No. 1 to figure pounds per acre. 8.4 ounces x 11.25 = 94.5 pounds per acre.
5.
To calibrate a seed not shown on the chart or a mix of different seeds, compare to a similar charted seed
to obtain a trial setting. Recalibrate as necessary.
6.
The same method may be used to determine fertilizer rates.
77/107
DRILLS
29
30
77/107
DRILLS
1/8
FERTILIZER
6
7
3
3
8
8
3
5
3
11
12
4
13
15
5
17
19
5
19
22
7
4
35
49
5
22
21
48
53
24
2
6
16
13
35
40
17
1
5
3
22
29
15
5
21
62
6
30
17
29
27
59
66
30
3
8
6
39
77
8
38
4
12
40
20
38
35
50
22
14
62
7
19
78
36
11
63
35
62
56
18
73
9
23
21
11
26
14
Following is the lineal feet of seeded row to seed 1 acre.
EXAMPLE:
150,000 beans on 7” row spacing
150,000 divided by 74,700 = 2.0 beans per ft.
10 ft. of row - 20 beans.
7” rows - 74,700 ft/acre
31
17
37
20
8
9
10
95 111 126 150 173
46 55 63 74 90
15 20 25 32 38
78 92 106 124 143
46 58 68 82 96
74 87 102 120 138
67 78 93
23
199
104
48
164
115
26
11
218
117
59
185
129
250
133
70
208
145
15
16
12
13
14
284
153 176 198
82 96 120 133 144 150 163 171 172
235
171 186 215 243 275 306 334 357 364
93 116 138 160 185 212 240 275 306 324 353 370 384 393 406 414 420 425
10
49
5
14
7
63
29
8
50
26
49
44
100 DRILL DETERMINING SEED POPULATION
24
24
9
27
30
10
13
POINTER SETTING
CHART FOR DRILLING GRAIN IN POUNDS PER ACRE
The 107 Drill seeds 10.50’ / 126” per pass; the 77 Drill seeds 7’/ 84” per pass.
The 107 Drill travels 4149 feet to seed 1 acre; the 77 Drill travels 6223’ to seed 1 acre.
18-46-0
1/8
1/8
1/8
1/8
3/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
WHEEL SPACE
WHEAT
BARLEY
OATS
RYE
SOYBEANS
BUCKWHEAT
SORGHUM OR VETCH
ALFALFA OR RAPE
MILLET
FLAX OR SUDAN GRASS
ORCHARD GRASS
FESCUE
SWITCH GRASS
SUNFLOWER (#3 6500/LB.)
Series 100
Spacing 7”
Model No. 77/107
77/107
DRILLS
31
44.5
3.8
6.3
12.1
2.0
9.4
6
53.7
5.3
8.1
14.7
2.7
13.5
63.9
6.7
11.7
17.7
4.1
16.6
7
77.7
8.6
14.4
20.7
5.4
21.1
89.9
10.9
18.9
24.5
7.2
27.0
8
102.0
13.9
22.9
28.5
9.0
33.7
115.0
16.0
27.4
31.3
11.3
37.7
9
131.0
18.8
32.0
34.7
13.5
45.4
145.0
21.7
36.4
40.0
16.7
53.0
11
12
13
42.7
54.8
34.0
26.1
42.2 56.5 66.5 75.9
43.7 50.3 54.8 60.9 69.3
19.8 22.7 25.6 30.1 34.6 40.2 45.8
61.1
10
65.8
14
2
3
4
5
4.4
6.3
2.7
8.5 15.3 22.9 30.6 39.5 53.0
8.3 15.5 23.4 33.5 44.5 57.5
2.7
0.9
3.6
3.4
0.9
1.0
1/8
1/8
1/8
1/8
1/8
1/8
1/8
RED TOP
REED CANARYGRASS
9
10
SERECIA (UNHULLED)
SWEET CLOVER
SWITCHGRASS
TIMOTHY
LOVEGRASS
7.9 10.9 14.0 17.2 20.6 24.8 29.4 33.9 39.1 44.7 50.6
3.8
7.4 10.6 14.1 19.0 25.0 30.8 37.1 45.2 54.2
2.3
4.7
2.7
7.2 12.1 17.5 24.3 34.1
7.2 14.4 23.4 33.5 44.5 58.9 77.3 97.5
5.5
7.6 10.5 14.8 20.1 25.8 31.6 38.3 46.2 54.1 60.9 69.7 82.6
5.5
3.5
0.9
9.5 16.4 24.3 32.8 43.4
4.3
1.0
8
1.9
4.7
1.1
8.3 12.4 17.3 23.6 31.3 39.8 49.2
1/8
0.9
7
8.8 12.1 16.1 20.4 25.1 30.8 37.5 44.1 50.0 57.3 65.2
8.1 15.5 25.0 35.2 46.4 59.8
2.9
1.6
3.4
1/8
1.3
6
8.1 13.9 19.8 27.0 35.5 48.5 57.5 71.1 85.8
0.7
3.6
RED CLOVER
1.0
1.3
LESPEDEZA (KOREAN)
0.4
1/8
1
POINTER SETTING
11
5
4
3
5.5 10.3 16.1 24.6 34.2
2.5
4.5
3.6 4.8 6.8 9.3
1.3
3.1 4.5 6.7
POINTER SETTING
LADINO CLOVER
KENTUCKY BLUEGRASS 1/8
ALFALFA
WHEEL SPACE
1/8
1/8 2.5
1/8
1/8
1/8
1/8
1/8
Spacing 7 Inch
*FEED COVER OFF
WHEEL SPACE
BAHIA GRASS
BUFFALO GRASS*
FESCUE
GREEN
ORCHARD GRASS
RYEGRA55
Spacing 7 Inch
73.4
15
16
32
77/107
DRILLS
1/8
1/8
1/8
1/8
1/8
1/8
1/8
1/8
3
4
5
6
8
5.7
8.1
3.8
12.6
4.5
8.5
4.4
7
3.1
5.8
2.5
4.9
2.9
5.8
2.7
9
7.6
3.6
12.1
5.5
19.3
7.1
12.1
7.3
POINTER SETTING
10
12.7
5.3
19.3
7.4
28.5
10.3
18.4
10.8
11
18.5
7.5
28.3
9.6
39.7
13.4
25.2
15.3
12
27.1
10.2
35.0
11.8
53.4
20.0
32.3
19.9
13
36.2
13.6
49.8
14.0
69.9
27.2
43.1
25.0
14
46.4
16.5
55.2
16.4
81.1
33.4
53.9
30.4
*DOUBLE AGITATOR MAY BE REQUIRED FOR EXTREMELY TRASHY SAMPLES
WHEEL SPACE
ALTI WILDRYE
BROMEGRASS*
INTERMEDIATE WHEATGRASS
KILLDEER SIDEOATS*
PUBESCENT WHEATGRASS
STEAMBANK WHEATGRASS
TALL WHEATGRASS
WESTERN WHEATGRASS
Spacing 7 Inch
35.5
19.3
86.1
35.1
15
47.4
20.0
39.8
22.5
16
49.8
20.7
77/107
DRILLS
33
64
60
36
46
46
64
BIRDSFOOT TREFOIL
MILLIT, TIBBET CLOVER
UNHULLED SERICEA
UNHULLED LESPEDEZA
BAHIA GRASS
LOVEGRASS
COMMON BERMUDA GRASS
FESCUE
PERENNIAL RYEGRASS
ORCHARD GRASS
RAPE MUSTARD
FLAX SESAME
SWITCHGRASS
TIMOTHY
NOTCHES ON INDEX
2.3
64
LBS.
BU.
50
55
55
53
17
31
27
1
2
2.7
1.7
1.4
2.3
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
9.6 11.8 14.6 17.4 20.3 23.1 26.4 28.7 31.5 33.8 36.0 40.5
6.2
8.4 10.7 11.8 14.6 16.9 18.6 20.8 22.5 24.2 25.9 27.6 28.1
8.4 11.8 15.2 18.0 21.9 25.3 28.7 32.6 35.4 38.3 41.6 45.0 50.1
6.8
5.0
1.1
2.3
0.8
4.2
3.7
4.5
5
6
7
8
9
10
11
12
13
14
15
16
8.7 11.6 14.7 17.5 20.6 23.1 26.5 29.6 32.4 35.5 37.9 40.5 44.5
9.6 12.4 15.8 18.6 20.8 24.2 28.1 30.9 33.8 37.1 39.9 42.2 47.8
9.6 12.9 16.9 20.9 24.8 28.1 32.6 37.1 40.5 44.4 46.7 49.5 54.6
4
3.9
5.6
2.8
5.6
7.3
3.4
5.1
5.6
6.8
7.3
8.4
9.0 10.1 10.7 11.3 11.9
6.8
8.4
9.6 11.3 12.4 13.5 15.2 16.9 18.0 19.1 21.9
9.0 10.7 11.8 13.5 15.2 16.9 18.6 20.8 21.9 23.1 24.8
3.9
7.4 10.6 14.3 17.6 20.8 25.1
2.8
3.4
1.7
7.4 10.2 12.9 16.4 19.2 22.5 25.6 28.2 31.8 34.9 37.7 40.5 43.3 45.9
6.2
6.8
6.2
3
7.9 11.3 16.3 20.3 24.2 28.7 32.6 36.6 42.2 46.7 51.2 55.1 57.9 60.2
5.1
5.6
4.5
7.7 10.7 14.3 17.4 21.2 26.1 28.5 30.9 35.5 39.4 42.8 46.7 51.0 55.9
7.9 10.7 14.1 17.4 21.4 25.3 28.1 32.1 36.0 39.4 42.2 46.7 50.1 55.1
8.4 12.4 17.4 22.5 26.4 30.9 37.1 41.6 46.7 51.2 56.3 59.6 63.0 66.4
7.7 10.7 13.6 17.0 20.4 23.9 27.3 30.9 31.7 37.9 41.3 44.7 47.6 50.6
3.9
5.1
2.8
3.9
2.8
4.9
4.5
5.1
4.7
1.7
2.3
1.1
1.7
1.1
2.1
2.3
2.2
1
62
LBS.
BU.
ALFALFA; RED, ALSIKE,
LADINO CLOVER; VETCH
SWEET CLOVER
NOTCHES ON INDEX
LBS/ACRE
5
5
2
NOTCH
2
2
1
5
DENSITY OF THE SAMPLES USED TO
PREPARE THIS CHART ARE GIVEN IN THE
FIRST COLUMN TO THE RIGHT OF THE
CROP NAME IN POUNDS PER BUSHEL.
WHEN USING HALF SPEED DRIVE DIVIDE
CHARTED RATES BY TWO. REPLACE 17
TOOTH SPROCKET ON COUNTERSHAFT
WITH 35 TOOTH. (SEE MANUAL FOR
DETAILS.)
ALFALFA
SWEET CLOVER
TIMOTHY
TOTAL
EXAMPLE:
ADD INDIVIDUAL SETTINGS.
SELECT THE SETTING FOR THE DESIRED
QUANTITY OF EACH SEED.
SEED MIXTURES
LEGUME BOX ATTACHMENT FOR 77/107 DRILL ON 7” SPACING
CHART FOR DRILLING LEGUMES AND SMALL GRASSES
IN POUNDS PER ACRE
4.11 Drilling with the Grain Drill
If the grain drill was transported using the optional end hitch, the rear wheels will need to be rotated as follows:
1.
Use the hydraulic system to lower the openers onto solid soil or use a jack to raise the drill frame and
remove the weight from the rear wheels.
2.
Remove the bolts from each wheel.
rotating the wheels for
drilling (wheel shown in
drilling position)
3.
Rotate the wheels 90° and insert bolts.
NOTE: Step 4 covers alignment of the wheels. Once this adjustment is set, it should not normally be
necessary to readjust it. Alignment of the wheels in the working position is less critical than in the
transport position because of the softer surfaces and slower speeds.
4.
34
Using a tape measure, align the wheels so that they are parallel with each other and the frame as shown
below. Adjust and secure the stop bolt #2.
77/107
DRILLS
5.
Tighten the bolts.
6.
Remove the jack, if used.
7.
After the tractor is hitched to the front hitch, move the drill ahead slowly until the front swivel wheels are
properly positioned.
At this point the grain drill should be properly set up and adjusted according to the instructions in the preceding
sections.
Load the tanks with seed and/or fertilizer. Rotate the drive wheel by hand to make sure that the feed wheel shafts are
free to turn. This is particularly important if the drill was transported with fertilizer and seed in the hoppers.
Start the tractor, retract the cylinder completely, and begin drilling.
Periodically check for proper seed depth and feed rate.
When the seeding operation is finished, park the drill over a sheet of plastic, canvas, etc. Pull one of the cleanout side
control levers out to empty the remaining seed or fertilizer. Collect the seed or fertilizer. Repeat the procedure for the
other hopper.
77/107
DRILLS
35
4.12 SUGGESTIONS
When preparing to sow damp fertilizer that has been sitting in the tank for several hours, stir the fertilizer all the way to
the bottom to break up any blocks of fertilizer which have become cemented together.
The amount of fertilizer sown will vary with the moisture content and quality of the fertilizer.
4.13 REAR WHEEL SWIVEL AND ADJUSTMENT
Both rear wheels are designed to swivel 90° for the purpose of transporting drills endways. Adjusting bolts are
provided for aligning wheels in transport position as well as in forward position. Transport position is most critical for
tire wear due to hard surface roads and faster speeds.
CAUTION: Transporting drills with seed and fertilizer in the tanks is not recommended. If drills
are moved any distance with seed or fertilizer in tanks, either in transport or field position, materials
will settle around feed wheels. Before starting to seed, operator should check with a wrench on drive
end of feed wheel shaft to make sure they are free to turn. Shaft may be turned either clockwise or
counterclockwise with openers in raised position.
WARNING: Maximum transport speed should never exceed 20 M.P.H., and should be less where
conditions demand.
4.14 TRANSPORTING THE GRAIN DRILL
The rear wheels swivel 90° to transport the drill end ways with the optional end hitch. These wheels must be carefully
aligned before transporting the drill because of the hard surfaces.
To rotate the rear wheels:
1.
Use the hydraulic system to lower the openers onto solid soil or use a jack to raise the drill frame and
remove the weight from the rear wheels.
2.
Remove the lock bolts from each wheel.
3.
Rotate the wheels 90° and insert the lock bolts.
NOTE: Step 4 covers alignment of the wheels. Once this adjustment is set, it should not normally
be necessary to readjust it.
36
77/107
DRILLS
4.
Using a string, align the wheels as shown. Adjust and secure the stop bolts.
5.
Tighten the lock bolts.
6.
Raise the openers or
remove the jack. Secure
the torque bar in the
transport position with
the safety stop bar.
7.
rear wheel alignment - transport position
After the tractor is hitched to the end hitch, move the drill ahead slowly until
the front swivel wheels are properly positioned.
rotating the wheels for
drilling (wheel shown in
drilling position)
step # 4
stop bolt
77/107
DRILLS
37
4.16 PREPARING FOR STORAGE
To prepare the 77/107 Drill for storage, perform the following steps:
1.
Install safety stop bar to keep planting units off the ground and to minimize rusting. Before drill is stored,
clean out slides should be opened to remove as much seed and fertilizer as possible. Both tanks should
be flushed out thoroughly to prevent any caking of seed or fertilizer. Open and close slides while flushing
to allow any fertilizer that might be under the calibration slide to work its way free. Fertilizer can be
damaging if left in contact with metal parts for a prolonged period.
2.
Clean all mud, dirt, grease and other foreign material from the exterior of the machine. Wash the
complete machine. Repaint places where bare metal is exposed - this will inhibit rusting.
3.
After inside of the tank is thoroughly dry, apply a coat of oil or diesel fuel to calibration slide, bearings
and other parts that have been in contact with fertilizer or seed.
4.
Remove the chains and wash them in solvent. Using a clean cloth, wipe off the chains. Soak the chains
in engine oil. Drain off the excess oil and install the chains on the grain drill.
5.
Coat all chains and exposed hydraulic cylinder rod with a Valvoline Tectyl 506 oil or equivalent.
6.
Lubricate machine thoroughly according to the lubrication instructions.
7.
Drain water from ballast tanks, if installed.
8.
If possible, store the machine in a dry, protected place. If it is necessary to store the machine outside,
cover it with plastic, waterproof canvas, or other suitable protective material.
9.
Check the machine for any worn or broken parts. By ordering parts now, you will avoid delays when it is
time to remove the machine from storage. When ordering parts always specify machine serial number
and the part number of the replacement part. Part numbers can be found in the Parts List Manual.
4.17 REMOVING FROM STORAGE
To remove the 77/107 Drill from storage, perform the following steps:
38
1.
Remove all protective coverings.
2.
Remove all excess oil from chains and cylinder rods. Lubricate machine in accordance with lubrication
instructions found in this manual.
3.
Check all hydraulic hoses for deterioration and, if necessary, replace. Tighten any loose bolts, nuts and
hydraulic fittings.
4.
Follow prestarting inspection.
77/107
DRILLS
Section 5: Lubrication
All 77/107 Grain Drills are completely serviced at the factory before shipping. However, the operator should make a
check of all grease fittings on the unit before beginning to operate it so as to become familiar with their location and
the correct service schedule.
Use only a high quality, multi-purpose grease when lubricating the unit. Make sure all fittings and the nozzle of the
grease applicator are clean before applying the grease. If any grease fittings are missing, replace them immediately.
Lubricating of all pillow block and flange-type self-aligning ball or roller bearings should be done slowly to help
prevent bearing seal damage. Use caution when using a high pressure, high volume gun.
Description
Type
Frequency
No. Zerks
1. Swivel Wheel Pivot
Grease
20 Hrs.
2
2. Torque Tube Bushings
Grease
40 Hrs.
2
3. Universal Joints
Grease
40 Hrs.
2
4. Square Drive Line
Grease
40 Hrs.
1
5. Feed Wheel Shaft
Grease
100 Hrs.
6
6. Roller Chains
Oil
Daily In Dusty Conditions
7. Tool Bar Bushing
Grease
20 Hrs.
2
8. Lift Arm Bushing
Grease
20 Hrs.
2
9. Lift Arm
Grease
20 Hrs.
2
10. Drive Wheel Frame
Grease
20 Hrs.
2
11. Packer Wheel Bearings and Coulter-Disk Bearings are Non-Relubable.
swivel wheel pivot
lubrication zerk
77/107
DRILLS
39
torque tube bushings
lubrication points
universal joints and
square drive line
lubrication zerks
feed wheel shaft
lubrication zerk
40
77/107
DRILLS
tool bar bushing
lubrication zerk
lift arm bushing
lubrication zerk
drive wheel frame
lubrication zerk
roller chains lubrication
77/107
DRILLS
41
APPENDIX A: WARRANTY
Duratech Industries International, warrants to the original purchaser for one year from purchase date that this product
will be free from defects in material and workmanship when used as intended and under normal maintenance and
operating conditions. This warranty is limited to the replacement of any defective part or parts returned to our factory
in Jamestown, N.D., within thirty (30) days of failure.
This warranty shall become void if in Duratech Industries International’s judgment the machine has been subject to
misuse, negligence, alterations, damaged by accident or lack of required normal maintenance, or if the product has
been used for a purpose for which is was not designed.
All claims for warranty must be made through the dealer which originally sold the product and all warranty
adjustments must be made through same.
This warranty does not apply to tires or bearings or any other trade accessories not manufactured by Duratech
Industries International. Buyer must rely solely on the existing warranty, if any, of these respective manufacturers.
Duratech Industries International shall not be held liable for damages of any kind, direct, contingent, or consequential
to property under this warranty. Duratech Industries International cannot be held liable for any damages resulting from
causes beyond its control. Duratech Industries International shall not be held liable under this warranty for rental costs
or any expense or loss for labor or supplies.
Duratech Industries International reserves the right to make changes in materials and/or designs of this product at any
time without notice.
This warranty is void if Duratech Industries International does not receive a valid warranty registration card at its office
in Jamestown, N.D., within 10 days from date of original purchase.
All other warranties made with respect to this product, either expressed or implied, are hereby disclaimed by Duratech
Industries International.
42
77/107
DRILLS
APPENDIX B: SPECIFICATIONS
77 drill
107 drill
Overall Width:
91"
123"
Seeding Width:
84"
126"
End Transport Width:
155"
Height:
73"
73"
Weight:
3360 lbs
3850 lbs
Tire Size- Front:
Tire Pressure
9.5x14 Implement
44 PSI
9.5x14 Implement
44 PSI
Tire Size- Rear:
Tire Pressure
7.6x14 implement
32 PSI
7.6x14 implement
32 PSI
Tire Size- Drive:
Tire Pressure
4.8x12 4-Ply
34 PSI
4.8x12 4-Ply
34 PSI
Hopper Capacity:
Grain- Front:
Granulated Fertilizer:
Grain- Front & Rear:
12 Bu.
11.5 Bu.
23 Bu.
14 Bu.
14 Bu.
28 Bu.
Feed System:
infinitely adjustable meter
infinitely adjustable meter
Hoses:
rubber convoluted
rubber convoluted
Row Spacing:
7"
7"
Openers - Double Disc: 14"
14"
Press Wheels - Standard: 2" x 15-1/2"
2" x 15-1/2"
Press Wheels - Optional: 2" x 13"
2" x 13"
Options:
Swivel Hitch
Acre Counter
Legume Box
Native Grass Kit
Light Kit
Ballast Tanks
Gauge Wheels
77/107
DRILLS
1-2-3-4 Drill Hitch and Components
Swivel Hitch
Acre Counter
Hitch Winch
Ballast Tanks
End Hitch
Stabilizer - Front and Rear
Legume Box
Native Grass Kit
Gauge Wheels
False Bottom
Light Kit
43
44
77/107
DRILLS
77/107 DRILL
107 DRILL - S.N. CJ 4427 & UP
77 DRILL - S.N. CJ 50177 & UP
Part 2:
Parts Reference
45
7 7 M A I N F R A M E A S S E M B LY
46
77/107
DRILLS
PARTS REFERENCE
7 7 M A I N F R A M E A S S E M B LY
ITEM
PART NO.
QTY.
DESCRIPTION
1
2600825
2600013
2600601
2600834
2600008
2600606
2900011
2900084
2900089
3000018
4800017
4800018
4800068
4800082
4800100
4800115
4800141
4800157
4800158
4800279
4900001
4900004
4900005
4900012
4900014
4900015
4900020
4900054
5000002
5000003
5000004
5000006
5000012
5000032
5000040
5000055
5000075
6100044
7500134
8400032
8400033
8400036
8400038
8400039
8400041
8400042
8400130
8400131
8400132
8400150
8400272
8400281
8400282
8400283
8400351
8400352
8400419
8400701
8400702
8400742
8800021
1
WHL\IMP\9.5X14\TIRE&RIM
TIRE\9.5LX14\8PLY
WHL\6-BOLT\14X8
WHL\IMP\7.60X15\TIRE&RIM
TIRE\7:60X15\8PLY;IMP
WHL\5-BOLT\15X5
HUB\WITH CONES\W/NUTS
SPACER\HUB\WHEEL
HUB\H-628(FORK)\COMPLETE
SPNDL\FORK
BOLT\HEX\3/4X3
BOLT\HEX\1/2X1-1/4
BOLT\HEX\1/2X3
BOLT\HEX\1/2X1-1/2
BOLT\HEX\5/8X4
BOLT\HEX\3/4X2-1/2
BOLT\HEX\1/2X4-1/2
PIN\COT\3/16X2
BOLT\HEX\5/8X4-1/2
PIN\RLLD\1/4X1-1/4
NUT\HEX\1/2\NC
NUT\HEX\3/4\NC
NUT\HEX\5/8\NC
NUT\TPLCK\5/8\NC
NUT\TPLCK\1/2\NC
NUT\NYLCK\1\NC
NUT\SLOT\1\NC
NUT\CASTLE\1/2\NF
WASH\FLAT\5/8
WASH\LOCK\5/8
WASH\FLAT\1/2
WASH\LOCK\1/2
WASH\LOCK\3/4
WASH\MACH\2IDX10GA
WASH\BUSH;MACH\1
WASH\SPINDLE\7/8
WASH\MACH\3X2-1/16X1/4
SPRNG\2-1/16X3/8WIRE2"LG
GROM 1.25ODX 17/32IDX1.25
GOOSENECK
HOSE\MINDER
TUBE\TORQUE\PIVOT
ARM\LIFT
BUSH\ARM\LIFT\1X5/8X2-1/8
SPNDL\REAR\WHL
BOLT\PIVOT\REAR\WHL
STEP\REAR\RH
STEP\REAR\LH
STRAP\REAR\STEP;MOUNT
BUSH\TOOL_BAR\1-1/4X3/4X2
TUBE\TORQUE
CAP\RETARDED\WHL\SWIVEL
ROD\THRDD\5/8X4
FORK\WHL\SWVL
RUN\DRILL\LH\ASSY
RUN\DRILL\LH\ASSY
PIN\LIFT_ARM\1X11-1/4
BAR\TOOL\7"SPCNG
WALKWAY\100_SERIES
FRM\MAIN\77
RETAINER\SPNDL
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
77/107
DRILLS
2
2
2
1
1
1
52
4
12
4
3
4
6
2
4
68
4
5
4
4
2
2
2
4
3
16
66
4
1
2
2
1
1
4
1
1
2
2
2
2
2
1
1
2
2
1
1
1
1
1
1
2
1
1
1
2
PARTS REFERENCE
47
1 0 7 M A I N F R A M E A S S E M B LY
48
77/107
DRILLS
PARTS REFERENCE
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
31
32
33
34
35
36
37
38
39
40
41
42
43
43A
44
45
46
47
48
49
50
52
53
54
55
56
57
58
8400031
8400032
8400033
8400034
8400417
8400272
8400036
8400273
8400150
8400419
8400038
8400039
8400040
8400131
8400130
8400132
8400041
8400042
2900014
2900015
2900016
na
2900004
2900018
5000055
4900054
2900013
2600606
2600008
2900012
4800044
2900011
8400043
8400044
2000032
8400103
4800527
4800107
2900008
2900007
2900006
na
2900069
2900004
2900018
5000056
4900055
2900048
2600601
2600013
2900010
4900015
4800158
4800100
4900012
5000002
5000003
1
1
1
1
1
1
1
1
2
2
2
2
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
10
3
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
6
2
2
4
4
4
3
Main Frame
Goose Neck
Hose Minder
Hitch Block
Hitch Block Pin 1" x 10"
Torque Tube
Torque Tube Pivot
Tool Bar 7" Spacing
Tool Bar Bushing 1-1/4" O.D. x 3/4" I.D. x 2" Long
Lift Arm Pin 1" x 11-1/4"
Lift Arm
Lift Arm Bushing 1" O.D. x 5/8" I.D. x 2-1/8" Long
Walk Way
Rear Step L.H.
Rear Step R.H.
Rear Step Strap
Rear Wheel Spindle
Rear Wheel Pivot Bolt
Grease Seal
Cone - Inner 1-3/8 Bore
Cup - Inner
Hub - 5 Bolt order 2900011
Cup - Outer
Cone - Outer
Washer\Spindle\7/8
Nut 7/8" 14" NF
Dust Cap
Wheel 15 x 5 - 5 Bolt
Tire 7.60 x 15-4 Ply Imp
Wheel Bolt
Cotter Pin 5/32 x 1-1/2
Hub (Complete w/Dust Cap) includes 19, 20, 21, 22, 23, 24, 27, & 31
Swivel Wheel Frame
Swivel Wheel Retainer Washer
Thrust Bearing T-199
Hold Up Bar (Transport)
3/4" x 2" Clevis Pin
1/8" Hair Pin
Grease Seal
Cone - Inner
Cup - Inner
Hub - 6 Bolt
Hub Assembly - Complete includes 40, 41, 42, 43, 44, 45, 48, & 52
Cup - Outer
Cone - Outer
Washer
Nut
Dust Cap
Wheel 14" 6" Bolt
Tire 9.5L x 14'’
Wheel Bolts
1" NC Lock Nut
5/8" x 4-1/2" Hex Bolt
5/8" x 4" Hex Bolt
5/8" Lock Nut
5/8" Flat Washer
5/8" Lock Washer
77/107
DRILLS
PARTS REFERENCE
49
50
77/107
DRILLS
PARTS REFERENCE
ITEM
PART NO.
59
4900005
60
4800017
61
4800115
62
5000012
63
4900004
64
4800063
65
4900139
66
4800106
67
4800018
68
4800082
69
5000004
70
5000006
71
4900001
72
4800157
73
4800044
74
4800141
75
3000002
76
3800041
77
3800126
78
3800111
79
3800082
80
4800279
81
8400283
82
2600601
83
2600013
82 & 83 2600825
85
2900083
86
5000075
87
5000032
88
8400282
89
6100044
90
8400281
91
4900005
92
5000003
93
4900115
94
4800157
95
5000056
96
8800021
97
2900084
98
2900085
99
2900086
100
2900087
101
na
102
2900089
103
3000018
104
2900090
105
8400349
106
8400611
107
8400612
108
8400450
77/107
DRILLS
QTY.
DESCRIPTION
2
1
3
4
4
2
2
1
4
12
4
18
20
6
1
4
1
4
1
1
4
2
1
1
1
5/8" Hex Nut
3/4" x 3" Hex Bolt
3/4" x 2-1/2" Hex Bolt
3/4" Lock Washer
3/4" Hex Nut
3/4" x 4" Bolt
3/4" Lock Nut Grade 8
5/8" x 1-1/2" Hex Bolt
1/2" x 1-1/4" Hex Bolt
1/2" x 1-1/2" Hex Bolt
1/2" Flat Washer
1/2" Lock Washer
1/2" Hex Nut
3/16" x 2" Cotter Key
5/32" x 1-1/2" Cotter Key
1/2" x 4-1/2" Hex Bolt
Spindle
1/8" Pipe Straight Zerk
1/8" x 2-5/8" Straight Zerk
1/8" 90° Straight Elbow
1/4" Tapered Straight Zerk (Serial No. 2672 and Up)
1/4" x 1-1/4" Rolled Pin (Serial No. 2672 and Up)
Swivel Wheel Fork
Wheel 14" x 6" 6 Bolt
Tire 9.5L x 14
WHL\IMP\9.5X14\TIRE & RIM
Wheel Bolt Nut 9/16"
3" O.D. x 2-1/16" I.D. x 1/4" Washer
2" I.D. x 10 Ga. Washer
5/8" x 4" Threaded Rod
Spring
Swivel Wheel Retarder Cap
5/8" Nut
5/8" Lock Washer
1" Castle Nut
1" Spindle Washer
Spindle Keeper
Spacer
Seal
Cone 2788
Cup 2720
Hub order 2900089
Hub Assembly includes 98, 99, & 100
Spindle (Not Shown)
9/16 x 2-1/4 Stud Bolt
Rear Wheel Pivot Mount
6
1
1
1
1
1
3
1
2
2
2
2
2
2
2
2
1
1
1
6
2
1
1
1
King Pin 2" O.D. x 11-1/2" Hardened
PARTS REFERENCE
51
7 7 D R I V E A S S E M B LY
52
77/107
DRILLS
PARTS REFERENCE
7 7 D R I V E A S S E M B LY
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
1000029
1000039
1000057
1000075
1000109
1100006
1100059
1100152
2000310
4800068
4800098
4900001
4900002
5000004
5000006
5000019
6200005
7400065
8400058
8400071
8400073
8400415
8400446
8400718
2
2
1
1
2
1
1
1
6
2
12
2
12
10
2
12
4
2
1
2
1
1
1
1
SPKT\50\B\14\1\1/4KW
SPKT\50\15\1/2\IDLER
SPKT\50\B\21\1\1/4KW
SPKT\50\B\36\1\1/4KW
SPKT\50\18\PL
CHAIN\50\73
CHAIN\50\CL
CHAIN\2050\84
BRG\FLG\CAST\1\2BOLT
BOLT\HEX\1/2X3
NUT\HEX\1/2\NC
NUT\HEX\3/8\NC
WASH\FLAT\1/2
WASH\LOCK\1/2
WASH\LOCK\3/8
KEY\SQ\1/4X1-1/2
SLV\SQ_HL\5/8X1-1/4OD
SPCR\DRV\1ODX.640IDX1L\>
SPKT\DRIVE\W/SQ_HL_SLV
SPCR\DRV\1ODX.640IDX1.25L
SHFT\1ST\1X8-3/4\1000
SHFT\1X8-1/2\ACRECTR
SHFT\1X21.5
77/107
DRILLS
PARTS REFERENCE
53
7 7 D R I V E W H E E L A S S E M B LY
54
77/107
DRILLS
PARTS REFERENCE
7 7 D R I V E W H E E L A S S E M B LY
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
2000310
2600042
2600618
2600822
2
1
1
1
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
3600008
3600103
3600105
3600106
3800082
4800080
4800082
4800098
4800157
4900001
4900002
4900005
4900014
5000002
5000006
5000019
6100032
6200005
8400023
8400024
8400025
8400026
8400310
8400414
8400442
8400626
2
2
1
1
2
3
4
4
2
3
4
3
4
1
3
4
1
1
1
1
1
1
1
1
1
1
BRG\FLG\CAST\1-1/4\2BOLT
TIRE\4.8X12\LUG\4PLY
WHL\12X4\4HL\RIM
WHL\ASSY\4.8X12\4-BOLT\LUG TREAD
includes items 2 & 3
CROSS BEARING KIT
1" YOKE
TUBE W/YOKE
SHAFT W/YOKE
FTG\LUB\1/4NFXZERK\ADAPT
BOLT\HEX\1/2X7
BOLT\HEX\1/2X1-1/2
PIN\COT\3/16X2
NUT\HEX\1/2\NC
NUT\HEX\3/8\NC
NUT\HEX\5/8\NC
NUT\TPLCK\1/2\NC
WASH\FLAT\5/8
WASH\LOCK\1/2
WASH\LOCK\3/8
SPRING\12-1/2X2-1/4 O.D. ( .406 WIRE )
KEY\SQ\1/4X1-1/2
PL\MNT\WHL\DR
ROD\SPRG\WHL\DR
GUIDE\SPRING\LONG
GUIDE\SPRING\SHORT
FRM\WHL\DR\WELD
AXLE\WHL\DRV
PIN\WHL\DR\1"X10 1/2"
BRKT\FORK\WHL\DRV\16-1/2X7-1/2
77/107
DRILLS
PARTS REFERENCE
55
1 0 7 D R I V E A S S E M B LY
56
77/107
DRILLS
PARTS REFERENCE
1 0 7 D R I V E A S S E M B LY
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12&13
13
14
15
15A
18
19
20
21
22
23
24
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
50
51
52
53
54
55
56
54
55
56
57
60
61
8400310
8400023
8400024
8400025
8400026
6100032
8400311
8400626
8400414
2000310
6200014
2600821
2600042
8400415
8400416
8400446
8400058
8400059
1100230
1100238
1000075
1000029
1000039
1000100
1100059
1100006
7400250
8400440
5000027
6100016
5000013
5000028
4800123
4800157
4800080
4800018
5000006
4900001
4900014
4800068
5000004
4800098
5000002
4900005
5000019
4900002
3600103
3600008
3600105
3600106
3600102
A 360025
A 360025
A 360024
1100228
3800082
4800034
1
1
1
1
1
1
1
Drive Wheel Frame
Drive Wheel Mount Plate
Drive Wheel Spring Rod
Spring Guide (Long)
Spring Guide (Short)
Spring
Pin, 1"x 10-1/2"
Drive Wheel Fork
Drive Wheel Shaft
1" Cast Flangette
1/4" Key, 1-1/4"
Wheel Asy., 4.80 x 12, 4 Bolt, Lug Tire
Tire, 4.80 x 12, Lug, 4 Ply
1st Shaft, 1 “ x 8-3/4”
2nd Shaft, 1" x 10"
SHFT\1X8-1/2\ACRECTR
Spacer, 1" x 1" O.D.
Spacer, 3/4" x 1" O.D.
A2050NP Conn. Link
A2050NP Chain. 84 Links w/CL
5036 Sprocket 1" Shaft 1/4KW
5014 Sprocket 1" Shaft 1/4KW
Idler Sprocket - 15 Tooth 50/15/1/2
5018 Sprocket
#50 Conn. Link
#50 Chain, 73 Links w/CL
Sq. Hole Sleeve w/K.W. 2-1/8"
Shaft 1" x 36"
Washers, 1-3/8" O.D. x 7/8" I.D. x 18 Ga.
Springs
Steel Washer, 5/8" Sq. Hole
Nylon Washer, 5/8" Sq. Hole
1/2" x 7" Hex Bolt
1/2" x 1-1/4" Hex Bolt
1/2" Lock Washer
1/2" Hex Nut
1/2" Lock Nut
1/2" x 3" Hex Bolt
1/2" Flat Washer
2 3/8" x 1-1/4" Hex Bolt
5/8” Flat Washer
5/8” Hex Nut
8 3/8" Lock Washer
0 3/8" Hex Nut
GRW 1" Yoke
GRW Cross & Brg.
LGW Tube w/Yoke
LGW Shaft w/Yoke
LGW Power Shaft Comp
1 Female Half G & G
1 Male Half G & G
1 G & G Power Shaft Comp
Chain/50NP/OL
1/4" Tapered Straight Zerk
3/8X1-1/2 Hex Bolt
77/107
DRILLS
1
8
7
1
1
1
1
1
1
1
1
1
1
3
1
2
1
1
2
1
8
2
2
2
3
1
3
4
3
3
4
2
4
1
1
2
1
2
2
2
1
1
1
4
3
1
2
2
4
PARTS REFERENCE
57
TA N K E N D D R I V E ( 7 7 & 1 0 7 )
58
77/107
DRILLS
PARTS REFERENCE
TA N K E N D D R I V E ( 7 7 & 1 0 7 )
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
1000029
1000039
1100234
1100257
2000310
2000802
4800003
4800034
4800053
4800068
4800098
4800168
4800230
4900001
4900002
5000001
5000004
5000006
5000019
5000084
6200014
7500515
8400070
8400071
8400073
8400074
8400242
8400243
8400244
8400274
8400440
1
1
1
1
1
2
3
1
1
1
4
1
5
1
15
2
6
1
15
2
1
2
2
1
1
1
1
1
1
1
1
SPKT\50\B\14\1\1/4KW
SPKT\50\15\1/2\IDLER
CHAIN\50NP\73
CHAIN\50NP\CL
BRG\FLG\CAST\1-1/4\2BOLT
CLLR\ECC\1-1/4
BOLT\HEX\3/8X8X1
BOLT\HEX\3/8X8X1-1/2
BOLT\CRG\3/8X1\NC
BOLT\HEX\1/2X3
BOLT\CRG\3/8X1-3/4\NC
SCR\CSK\ALN\3/8X1-1/2\NC
NUT\HEX\1/2\NC
NUT\HEX\3/8\NC
WASH\FLAT\3/8
WASH\FLAT\1/2
WASH\LOCK\1/2
WASH\LOCK\3/8
2”PD 1-1/4ID OILITE WASHER
KEY\SQ\1/4X1-1/4
PLASTIC PLUG 107 DRILL
BRG\1-1/4\W/BRKT\3-HL
SPKT\DRIVE\W/SQ_HL_SLV
SPCR\DRV\1ODX.640IDX1.25L
PL\SEAL\TANK\DRILL
PL\SEAL\TANK\107
SHLD\DR\AGTTR\SGL
TANK\WLDMNT\S/N2672\107
PLUG\TANK\STL\107DRILL
SHFT\1X36\100 DRILL
77/107
DRILLS
PARTS REFERENCE
59
R U N A S S E M B LY ( 7 7 & 1 0 7 )
60
77/107
DRILLS
PARTS REFERENCE
R U N A S S E M B LY ( 7 7 & 1 0 7 )
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
41
42
43
44
45
46
47
2000031
4800063
4800071
4800076
4800079
4800160
4800161
4800218
4800231
4800652
4900003
4900005
4900012
4900014
4900035
4900139
5000023
5000002
5000003
5000005
5000009
5000022
5000067
7400258
7400264
7500097
7500098
7500160
7500187
7500188
7500307
8400025
8400026
8400047
8400048
8400049
8400064
8400340
8400341
8400355
8400567
8400568
8400617
8400670
8400673
6100032
8400671
8400672
2
1
1
1
2
4
6
4
1
1
1
3
6
7
4
1
1
1
1
10
6
1
4
2
2
1
1
2
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
BRG\ROW\DBL
BOLT\HEX\3/4X4
BOLT\HEX\5/16X1-1/4
PIN\KLIK\5/16
BOLT\HEX\5/8X2-1/2
BOLT\HEX\7/16X1-1/4
SCR\BUT\ALN\1/2X1\NC
BOLT\HEX\5/8X5-1/2
BOLT\HEX\1/2X3-3/4
NUT\HEX\5/16\NC
NUT\HEX\5/8\NC
NUT\TPLCK\5/8\NC
NUT\TPLCK\1/2\NC
NUT\TPLCK\7/16\NC
NUT\TPLCK\3/4\GR8\NC
WASH\FLAT\5/16
WASH\FLAT\5/8
WASH\LOCK\5/8
WASH\FLAT\3/4
WASH\1" OD\ SHIM
WASH\LOCK\5/16
WASH\HEX\15/16IDX1.75X7GA
CAP\DUST
CAP\WHL\W/O_PILOT
CONVOLUTED HOSE
CLAMP\SDHOSE\1-1/4\A-24
#6610 BREAING BUSHING
BLADE\ASSY\14"\COULTER
BLADE\ASSY\DISC\14"
CAP\SPACER\BUSHING
GUIDE\SPRING\LONG
GUIDE\SPRING\SHORT
ROD\SPG\5/8X15
LINK\RUN\UPPER
LINK\RUN\LWR
ROD\DEPTH\WHEEL\PACKER
FRM\RUN\FR\107\SN672
FRM\RUN\REAR\107\SN2672
WHL\PRESS\STL\SUB-ASY
BOOT\DRILL\LH\ASSY
BOOT\DRILL\RH\ASSY
WHL\PRESS\STL\ASSY
SCRPR\DISC
TUBE\FRM\RUN\REAR
SPRING\12-1/2X2-1/4 O.D. ( .406 WIRE )
GUIDE\TUBE\LH\FRM\RUN\REAR
GUIDE\TUBE\RH\FRM\RUN\REAR
77/107
DRILLS
PARTS REFERENCE
61
7 7 TA N K A S S E M B LY ( D E TA I L A )
62
77/107
DRILLS
PARTS REFERENCE
7 7 TA N K A S S E M B LY ( D E TA I L A )
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
4800118
4900002
4900003
5000019
5000022
5000023
6100002
8300355
8400705
8400715
8700015
4
49
21
69
21
16
12
4
1
2
2
BOLT\HEX\5/16X2
NUT\HEX\3/8\NC
NUT\HEX\5/16\NC
WASH\LOCK\3/8
WASH\LOCK\5/16
WASH\FLAT\5/16
SPRING\COMP\.072W\11/16OD\2-1/8LONG
LATCH\GUARD\WIND\8000
PL\CNTRL\7" SPACING
GUARD\WIND
CUP\SEED\CTR\LB
77/107
DRILLS
PARTS REFERENCE
63
7 7 TA N K A S S E M B LY ( D E TA I L B )
64
77/107
DRILLS
PARTS REFERENCE
7 7 TA N K A S S E M B LY ( D E TA I L B )
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
3800082
4800003
4800012
4800053
4800114
4800164
4900002
4900014
4900023
5000001
5000016
5000019
6100002
7501058
8300236
8400112
8400243
8400658
8400703
8400704
8400707
8400709
8400717
6
15
12
13
14
20
49
13
2
61
27
69
12
4
8
2
1
1
1
2
1
1
2
BOLT\HEX\3/8X1
BOLT\CRG\3/8X1\NC
BOLT\HEX\1/2X2
BOLT\HEX\3/8X3/4
NUT\HEX\3/8\NC
NUT\TPLCK\1/2\NC
NUT\TPLCK\3/8\NC
WASH\FLAT\3/8
WASH\FLAT\7/16
WASH\LOCK\3/8
SUP\SHFT\ASSY\SLEEVE
WASH\BENT\1/2"
HDL\PL_CLEANOUT
SHLD\DR\AGTTR\SGL
WHL\FEED\33-1/16\FR\CTR
TANK\WLDMNT\77
PL\CLEANOUT\TANK
WHL\FEED\23-15/16\FR\RH
WHL\FEED\19"\FR\LH
COV\DIVIDER
77/107
DRILLS
PARTS REFERENCE
65
7 7 TA N K A S S E M B LY - B A C K
66
77/107
DRILLS
PARTS REFERENCE
7 7 TA N K A S S E M B LY - B A C K
ITEM
PART NO.
QTY.
DESCRIPTION
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
4900002
4900014
4900030
5000001
5000016
5000019
5000036
5000128
6100002
6100017
7500108
7500562
7501058
8400003
8400004
8400005
8400011
8400279
8400280
8400659
8400706
8400711
8400713
8400719
49
13
6
61
27
69
4
4
12
4
4
4
4
4
2
2
6
1
1
1
1
1
1
4
NUT\HEX\3/8\NC
NUT\TPLCK\1/2\NC
NUT\NYLCK\3/8\NC
WASH\FLAT\3/8
WASH\FLAT\7/16
WASH\LOCK\3/8
WASH\1-3/4ODX.890ID
WASH\FLAT\3/8\RBBR\EPDM
PRESSURE SPRING 12X1 1/8
HSG\CAST\BUSH\TANK\DRILL
SLV\SQ_HL\5/8X1-7/16\W/5/16_THRU_HL
SUP\SHFT\ASSY\SLEEVE\107
ROD\COV\TANK\SPG
RTNR\TANK\COVER\SPG\LH
RTNR\TANK\COVER\SPG\RH
CLMP\WHL\COV\HOLD DOWN
CUP\SEED\CENTER\RH
CUP\SEED\CENTER\LH
WHL\FEED\33-1/16\REAR\CTR
PL\CNTRL\7"SPACING
WHL\FEED\23-15/16\REAR\RH
WHL\FEED\19\REAR\LH
COV\WHL\FEED\77
41
42
43
44
45
7500066
7500006
7500007
7500068
7500107
96
24
24
24
48
FEED WHEEL RETAINER CLIP
FEED WHEEL COMPLETE
FEED WHEEL LEFT HALF (MARK L)
FEED WHEEL RIGHT HALF (MARK R)
HOSE CLAMP
77/107
DRILLS
PARTS REFERENCE
67
1 0 7 TA N K A S S E M B LY
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
8400244
8400107
8400003
6100017
8400004
8400005
8400114
8400007
6100031
5000002
6100002
8400110
8400111
1
2
4
4
2
2
1
6
6
6
20
2
4
Tank Weldment 106"
Tank Cover
Tank Cover Spring Rod
Tank Cover Spring
Tank Cover Spring Retainer L.H.
Tank Cover Spring Retainer R.H.
Control Plate, 7" Spacing
Control Plate Guide
Control Plate Guide Spring
Guide Washer
Springs
Clean Out Plate
Feed Wheel Covers
6
7
8
9
10
11
12
68
77/107
DRILLS
PARTS REFERENCE
1 0 7 TA N K A S S E M B LY
ITEM
PART NO.
QTY.
DESCRIPTION
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
7500006
7500007
7500008
7400066
7500107
8400011
6100002
7500110
7500108
7500109
5000036
4800169
5000027
4800050
8400426
8400423
8400425
8700016
8700015
8300236
4800044
4800156
4900030
4800053
4800012
5000001
5000019
4900002
4800003
4800170
5000022
4900003
4800396
4800114
4900014
5000016
6500022
8400112
8400245
8400248
8400249
8400250
8400251
3800082
7500134
4800068
5000004
8400318
4800164
5000001
5000019
8400467
8400462
8400280
8400463
8400279
4900035
36
36
36
144
36
6
6
4
4
4
4
2
4
2
2
2
2
4
4
8
8
6
6
26
6
20
40
40
8
6
6
6
6
19
19
25
1
2
1
1
1
1
1
6
4
4
12
2
28
28
28
2
1
1
1
1
6
Feed Wheel Complete
Feed Wheel Left Half (Marked L)
Feed Wheel Right Half (Marked R)
Feed Wheel Retainer Clips
Hose Clamp
Feed Wheel Cover Hold Down
Wheel Cover Hold Down Spring
Cast Bracket w/Brg. Complete
Cast Bracket
Steel Brg. w/Hole
Retainer Washer
1/4" x 1-1/8" Rolled Pin
Washer, 1-3/8" O.D. x 7/8" I.D.
Shaft Right Side, 38-7/16"
Shaft Center, 33-1/16"
Shaft Left Side. 34-1/2
Seed Cup End Section
Seed Cup Center Section
1/2" Flat Washer w/40° Brk.
3/8" x 3" Hex Bolt
3/8" Plastic Insert Lock Nut
3/8" x 1" Carriage Bolt
3/8" x 1-1/4" Carriage Bolt
3/8" Flat Washer
3/8" Lock Washer
3/8" Hex Nut
3/8" x 1" Hex Bolt
5/16" x 3-1/2" Bolt
5/16" Lock Washer
5/16" Hex Nut
7/16" x 2" Bolt
1/2" x 2" Bolt
1/2" Top Lock Nut
7/16" Flat Washer
Calibration Decal, 7" Spacing
Clean Out Handle
Control Plate 7" Spacing (Grass)
Seed Cup Left End Section (Grass)
Seed Cup Left Center Section (Grass)
Seed Cup Right Center Section (Grass)
Seed Cup Right End Section (Grass)
1/4" Tapered St. Zerk
Grommet
1/2" x 3" Bolt
1/2" Flat Washer
Divider Cover
3/8" x 3/4" Bolt
3/8" Flat Washer
3/8" Lock Washer
Wind Guard (Not Shown)
Seed Cup Left End Section (Rear) Not Shown
Seed Cup Left Center Section (Rear) Not Shown
Seed Cup Right End Section (Rear) Not Shown
Seed Cup Right Center Section (Rear) Not Shown
7/16" Toplock Nut
77/107
DRILLS
PARTS REFERENCE
69
S E E D & F E R T I L I Z E R S E T T I N G A S S E M B LY
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
2000313
2000811
4800013
4800153
4900003
5000022
5000023
7500071
7500072
7500073
8400060
1
1
2
4
6
4
4
1
1
1
1
BRG\FLG\CAST\3/4\2BOLT
CLLR\LOCK\3/4
BOLT\HEX\5/16X1
NUT\HEX\5/16\NC
WASH\LOCK\5/16
WASH\FLAT\5/16
CALIBRATION POINTER NUT
CALIBRATION CONTRL PL NUT
CALIBRATION SHAFT #6620
HDL\CAL
NOT SHOWN
6500016
6500017
6500081
70
77/107
DRILLS
DECAL\INFO\CAL;SCALE;GRAIN
DECAL\INFO\CAL.SCALE;FERT
DECAL\INFO\CAL.SCALE;GRASS
PARTS REFERENCE
S C R A P E R A S S E M B LY
ITEM
PART NO.
QTY.
8400091
1
2
3
4
5
77/107
8400670
4800071
5000023
5000022
4900003
DRILLS
DESCRIPTION
Scraper Assembly - Complete
2
1
1
1
1
Scraper\Disc
5/16" x 1-1/4" Bolt
5/16" Flat Washer
5/16" Lock Washer
5/16" Hex Nut
PARTS REFERENCE
71
C O U LT E R & D I S K A S S E M B LY
72
ITEM
PART NO.
QTY.
DESCRIPTION
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
7500064
2000031
7500165
4800161
1
1
1
6
5
6
7
8
4900014
7500187
7500160
5000009
6
1
1
2
Coulter, 14" - 6 Hole
Brg.
Cage
1/2" - 13 x 1"
Button Hd. Socket Screw
Lock Nut, 1/2"
Coulter (Complete)
Sleeve
Shim Washer
1
2
3
4
5
6
7
7500010
2000031
7500167
4800039
7500188
7500160
5000009
1
1
1
12
1
1
2
Disk, 14"
Brg.
Cage
Rivets, 1/4" x 1/2"
Disk (Complete)
Sleeve
Shim Washers
77/107
DRILLS
PARTS REFERENCE
P R E S S W H E E L A S S E M B LY
TO RETROFIT DRILL WITH SERIAL NO. 1550 & UP
ORDER PART 8400617 & 4800063
PART NO.
QTY.
DESCRIPTION
8400617
2000061
7500653
8400616
7400264
4800063
4900139
2
1
1
2
1
1
Press Wheel Assembly
Brg/3/4/FHR204-12
Spcr/Wheel/Packer/107
Whl/Stl; Packer/107
Packer Wheel Cap - No Pilot
Bolt\Hex\3/4 x 4
Nut\Toplock\3/4
77/107
DRILLS
PARTS REFERENCE
73
H U B A S S E M B LY
74
77/107
DRILLS
PARTS REFERENCE
H U B A S S E M B LY
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
2900004
2900011
2900013
2900014
2900015
2900016
2900018
4900094
1
1
1
1
1
1
1
5
CUP\INNER\WHEEL HUB
HUB\WITH CONES\W/NUTS
CAP\DUST\WHL;HUB(DC-13)
SEAL\GREASE(517) (15190)
CONE\INNER/WHL HUB(48548)
CUP\INNER\WHL:HUB(48510
CONE\OUTER\WHL;HUB(67048
NUT\TAPER\WHEEL\1/2\NF\
77/107
DRILLS
PARTS REFERENCE
75
H U B F O R K A S S E M B LY
ITEM
1
2
3
4
5
76
PART NO.
QTY.
2900085
2900086
2900087
2900089
4900094
2
2
2
1
6
77/107
DRILLS
DESCRIPTION
SEAL\WHL;HUB(20078)
CONE\2788\WHL;HUB
CUP\BRG\HUB\WHL\2720
HUB\H-628(FORK)\COMPLETE
NUT\TAPER\WHEEL\1/2\NF\
PARTS REFERENCE
F R O N T S TA B I L I Z E R O P T I O N ( 1 0 7 O N LY )
NOTE: For drill with disc type banding openers, mount stabilizer in front of banding tool bar. See illustration.
NOTE: A
Space tool bars 3" apart for 7" spacing.
Space tool bars 10" apart for paired row 6-14 spacing.
Mount double clamps as far apart as possible.
Space tool bars 6" apart for 10" spacing.
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
8400183
8400184
8400185
4800183
5000005
5000012
4900004
4800185
4800157
4800199
8400186
1
1
1
4
8
16
16
1
1
4
4
Male Stabilizer
Female Stabilizer
1-1/2" O.D. x 1" I.D. Bushing
3/4" L-Bolt 5-1/4" O.D. x 5-1/4" O.D.
3/4" Flat Washer
3/4" Lock Washer
3/4" Hex Nut
1" x 3" Clevis Pin
3/4" L-Bolt 5-1/4" O.D. x 7-1/4" O.D.
Double Clamp
77/107
DRILLS
PARTS REFERENCE
77
R E A R S TA B I L I Z E R O P T I O N ( 1 0 7 O N LY )
78
77/107
DRILLS
PARTS REFERENCE
R E A R S TA B I L I Z E R O P T I O N ( 1 0 7 O N LY )
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
4800183
4800626
4800647
4900004
4900015
5000012
5000115
8400201
8400202
8400203
4
1
1
8
2
8
4
1
1
1
BOLT\L\3/4\5-1/4X5-1/4
BOLT\HEX\1X11\NC
BOLT\HEX\1X4\NC
NUT\HEX\3\4\NC
NUT\NYLCK\1\NC
WASH\LOCK\3/4
WASH\FLAT\3/4\EXTRTHK\GR8
BAR\STBLZR\CTR\REAR
MNT\STBLZR\RH\REAR
MNT\STBLZR\LH\REAR
11
8400378
1
Rear Stabilizer Kit 2 Drill
12
8400040
77/107
DRILLS
WALKWAY\100_SERIES
PARTS REFERENCE
79
T O W H I T C H ( 1 0 7 O N LY )
80
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
8400226
8400227
8400228
8400229
8400230
8400231
4800046
4800050
4800041
4800082
5000006
4900001
1
1
1
1
2
1
2
2
10
4
14
14
End Tow Hitch
Front Mount
Rear Mount
Front Mount Strap
Mount Straps
Hold Up Handle for End Tow Hitch
3/4" x 3" Pin
3/16" x 1-1/2" Cotter Pin
1/2" x 5" Bolt
1/2" x 1-1/2" Bolt
1/2" Lock Washer
1/2" Hex Nut
77/107
DRILLS
PARTS REFERENCE
BALLAST BRACKET (77 & 107)
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
8400211
8400178
5000005
4900004
5000001
5000019
4900002
4800183
5000012
4800146
8400474
4
4
8
8
8
8
8
4
8
8
Saddle
TLE Strap
3/4" Flat Washer
3/4" Hex Nut
3/8" Flat Washer
3/8" Lock Washer
3/8" Hex Nut
3/4" L-Bolt
3/4" Lock Washer
3/8" x 2" Bolt
Kit - 2 Barrel Mount Bracket
77/107
DRILLS
PARTS REFERENCE
81
H I T C H L I F T ( 1 0 7 O N LY )
82
77/107
DRILLS
PARTS REFERENCE
H I T C H L I F T ( 1 0 7 O N LY )
ITEM
PART NO.
QTY.
8400589
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
77/107
8300293
8300294
5800004
5800311
1400082
4800030
4800123
4800027
7500121
8300356
8300295
8300296
8300297
4800119
4900005
4800188
4800235
5000004
5000006
4900001
4800017
4800098
5000001
5000019
4900002
4800107
8300298
8300299
4800188
4800141
DRILLS
DESCRIPTION
Hitch Lift Kit (only for 3 or more drill hitch set-up)
1
1
1
1
1
1
1
2
1
1
1
1
1
4
2
2
4
6
6
2
3
6
3
3
1
1
1
2
2
Lift Frame
Lift Mount Strap 2" x 6"
Winch
1/4" Cable 12' Long
Cable Sheaves
5/8" x 2" Clevis Pin
1/8" x 1 -1/2" Cotter Pin
1/4" Cable Clamp
1/4" Cable Thimble
I Bolt
Hold Up Bar 2" x 11-1/2"
Hold Up Bar Mount 4-1/2" Long
Hold Up Bar Strap 4-1/2" Long x 2"
5/8" x 3-1/2" Clevis Pin
5/8" Nuts
1/2" x 4" Bolt
1/2" x 6-1/2" Bolt
1/2" Flat Washer
1/2" Lock Washer
1/2" Hex Nut
3/4" x 3" Bolt
3/8" x 1-1/4" Bolt
3/8" Flat Washer
3/8" Lock Washer
3/8" Hex Nut
1-1/8" Hair Pin
Hold Up Bar Mount
Hold Up Bar Strap
1/2" x 4" Hex Bolt
1/2" x 4-1/2" Hex Bolt
PARTS REFERENCE
83
DRILL SINGLE HITCH (77 & 107)
84
77/107
DRILLS
PARTS REFERENCE
DRILL SINGLE HITCH (77 & 107)
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
2A
3
3A
8400664
8400569
4800626
4800157
4900015
1
1
1
2
1
Hitch\SINGLE\107& 8000
1" x 12" Hitch Pin
BOLT\HEX\1X11\NC\GR5
NUT\NYLCK\1\NC
NOT SHOWN
8400650
8400579
8400307
1100221
77/107
DRILLS
2 WAY SWIVEL HITCH
STEEP TERRAIN HITCH
SINGLE DRILL HITCH KIT
CHAIN\3/8\GR43\5FT\W/HOOKS
PARTS REFERENCE
85
2 D R I L L H I T C H ( 1 0 7 O N LY )
86
77/107
DRILLS
PARTS REFERENCE
2 D R I L L H I T C H ( 1 0 7 O N LY )
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
4800010
4800085
4800125
4800226
4800546
4800626
4900001
4900002
4900005
4900015
5000001
5000002
5000003
5000006
5000019
7500170
8300326
8300341
8300498
8400034
8400193
8400196
OR
8400667
8400666
8800095
8800096
1
8
10
2
2
2
8
12
1
5
4
1
1
8
12
1
10
1
1
2
1
1
BOLT\HEX\5/8X2
BOLT\HEX\1/2X1
BOLT\HEX\3/8X1-3/4
BOLT\HEX\3/8X5-1/2
BOLT\HEX\1X5\NC
BOLT\HEX\1X11\NC
NUT\HEX\1/2\NC
NUT\HEX\3/8\NC
NUT\HEX\5/8\NC
NUT\NYLCK\1\NC
WASH\FLAT\3/8
WASH\FLAT\5/8
WASH\LOCK\5/8
WASH\LOCK\1/2
WASH\LOCK\3/8
HOSE MINDER
MNDR\HOSE
WASH\2X1.028X3/8
PIN\HITCH
HITCH\BLK
HITCH\2\DRILL\107
BLK\HITCH
1
4
1
1
BLK\HITCH\CLEVIS
STEP\XTNSN\WLKWY
MNT\MINDER\HOSE\DRILL
STRAP\MINDER\HOSE\DRILL
8400394
1
2 DRILL HITCH KIT (INCLUDES REAR STABILIZER KIT)
23
24
25
77/107
DRILLS
PARTS REFERENCE
87
3 - 4 D R I L L H I T C H ( 1 0 7 O N LY )
88
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
8400196
8300498
8300341
4900015
7500170
8800095
8800096
5000001
4800226
4800089
8300329
4800142
5000019
4900002
5800601
8400194
8400197
8400195
4800010
5000002
5000003
4900005
4800187
4900015
8300497
Hitch Block
Hitch Block Pin
2" O.D. x 1.028 I.D. 3/8" Thick Washer
1" Nylon Insert Nut
Hose Minder
Hose Minder Mount
Hose Minder Strap
3/8" Flat Washer
3/8" x 5-1/2" Bolt
3/8" x 4" Bolt
Hose Clamp
3/8" x 1-3/4" Bolt
3/8" Lock Washer
3/8" Nut
Jack 2 SM-10
3" Drill Center Pole
4" Drill Center Pole
Small Wings
5/8" x 2" Bolt
5/8" Flat Washer
5/8" Lock Washer
5/8" Nut
1" x 6" Bolt
1" Nylon Insert Nut
1" x 6" Hitch Pin
26
4800103
1
1
1
1
2
2
2
4
2
2
4
4
8
8
1
1
1
2
2
2
2
2
4
4
1 Per
Drill
1 Per
Drill
77/107
DRILLS
1/4" x 2" Cotter Pin
PARTS REFERENCE
SINGLE DRILL & 2 DRILL HYDRAULICS
100 Series
Single Drill Depth
Control Hydraulics
ITEM
PART NO.
QTY.
DESCRIPTION
A
B
C
D
4100039
3700023
3700153
3800008
1
1
1
3" x 8" Cylinder
96"- 1/2" Hose
108" - 1/2" Hose
2
90° St. Elbow
NOT SHOWN
4100045
3x8 Seal Kit - Hyd Cyl.
100 Series
Two Drill Depth
Control Hydraulics
ITEM
PART NO.
QTY.
DESCRIPTION
A
B
C
D
E
F
4100039
3700119
3700120
3700061
3800086
3800009
2
1
1
2
2
3" x 8" Cylinder
216" - 1/2" Hose
240" - 1/2" Hose
132" - 1/2" Hose
1/2" x 1-1/2" Nipple
2
1/2" Tee
NOT SHOWN
4100045
77/107
DRILLS
PARTS REFERENCE
89
3 D R I L L H Y D R A U L I C S ( 1 0 7 O N LY )
ITEM
PART NO.
QTY.
DESCRIPTION
A
B
C
D
E
F
4100039
3700118
3700119
3700061
3800086
3800009
3
1
1
4
4
4
3" x 8" Cylinder
192" - 1 /2" Hose
216" - 1/2" Hose
132" - 1/2" Hose SW-SO
1/2" x 1-1/2" Nipple
1/2" Tee
NOT SHOWN
4100045
90
77/107
DRILLS
PARTS REFERENCE
4 D R I L L H Y D R A U L I C S ( 1 0 7 O N LY )
ITEM
PART NO.
QTY.
DESCRIPTION
A
B
C
D
E
F
4100039
3700095
3700101
3700061
3800086
3800009
4
1
1
6
6
6
3" x 8" Cylinder
252" - 1/2" Hose SW-SO
276" - 1/2" Hose SW-SO
132" - 1/2" Hose SW-SO
1/2" x 1-1/2" Nipple
1/2" Tee
NOT SHOWN
4100045
77/107
DRILLS
PARTS REFERENCE
91
DECALS
2
1
4
5
2A
3
6
7
8
9
11
10
13
12
14
15
16
92
77/107
DRILLS
PARTS REFERENCE
DECALS
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
2A
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
6500020
6500058
6500348
6500060
6500016
6500017
6500081
6500022
6500061
6500062
6500063
6500101
6500042
6500064
6500041
6500040
6500182
6500163
6500102
2
2
HAYBUSTER 3”
107 3”
DECAL\LOGO\77\TANK
IMPORTANT Avoid Making Sharp Turns
Calibration Scale Grain
Calibration Scale Fertilizer
Calibration Scale Grass
Calibration Decal 7" Spacing
Seed Depth, Soil Penetration Ext.
IMPORTANT STORAGE
IMPORTANT Feed Wheel Shaft
WARNING No Riders
Keep Wheel Bolts Tight
Engage Locks
WARNING For Your Protection
WARNING Keep All Shields In Place
Ag Chemical Warning
WARNING Disc Blades
4 Red Stripe Decal\logo\stripe\red
LEGUME BOX DECALS
1
6500304
2
6500305
2A
6500349
18
6500102
19
6500083
7500077
7500092
7500091
7500078
7500105
7500104
17
2
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
6
1
HAYBUSTER 1-3/4”
107 Decal 1-3/4
DECAL\LOGO\77\LEGUME
1/2 Ft. Red Strips
Chart 7" Spacing
12 Oz Yellow Spray Paint
Quart Yellow Paint
Gallon Yellow Paint
12 Oz Red Spray Paint
Quart Red Paint
Gallon Red Paint
18
19
77/107
DRILLS
PARTS REFERENCE
93
D E C A L L O C AT I O N S
14
11
1
13
11
1
9
10
8
7
16
6
DECAL LOCATION (See page 93 for descriptions)
94
77/107
DRILLS
PARTS REFERENCE
19
2
11
D E C A L L O C AT I O N S
ITEM
PART NO.
QTY.
1
DESCRIPTION
19
14
2
18
15
3
11
DECAL LOCATION (See page 93 for descriptions)
77/107
DRILLS
PARTS REFERENCE
95
77 LEGUME BOX OPTION
96
77/107
DRILLS
PARTS REFERENCE
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
1000111
1000112
1100224
1100232
1100233
2000002
2000016
2000703
3800082
4800003
4800013
4800029
4800127
4800153
4800156
4800164
4800213
4800643
4900002
4900003
4900040
5000001
5000019
5000022
5000023
6100002
6200010
8400722
8400723
8700001
8700002
8700003
8700006
8700008
8700009
8700010
8700011
8700012
8700013
8700014
1
2
2
1
1
4
2
4
8
4
4
2
6
10
4
4
26
3
14
18
27
10
14
18
12
2
3
1
1
1
1
4
2
1
1
1
1
1
1
3
SPKT\40\B\17\1\1/4KW\SOFT
SPKT\40\B\15\1\1/4KW
40NP PITCH CONNECTOR LINK
53 LINKS 40NP PITCH CHAIN
77 LINKS 40NP PITCH CHAIN
1" BEARING W/ LOCK COLLAR
BLK\WOOD\IDLER
2 HOLE FLANGETTE
BOLT\HEX\3/8X1
BOLT\HEX\5/16X1
BOLT\HEX\3/8X2-1/2
PIN\COT\1/8X1
BOLT\HEX\3/8X3
BOLT\HEX\3/8X3/4
SCR\PAN\SLOT\1/4X5/8\NC
BOLT\HEX\5/16X3/4
NUT\HEX\3/8\NC
NUT\HEX\5/16\NC
NUT\FLG\SERR\1/4\NC
WASH\FLAT\3/8
WASH\LOCK\3/8
WASH\LOCK\5/16
WASH\FLAT\5/16
KEY\SQ\1/4X1
CVR\BOX\LEGUME
SHFT\3/8SQX50-3/4\LGUM;BX
BRKT\LEGUME\RH\LEG-BOX
ROD\SPG\COV\BOX
BRG\BOX\LEGUME\RH
BRG\BOX\LEGUME\LH
SPRKT\17T\LEG.BOX
SHFT\1X29\LEGUMEBOX
BRKT\LEGUME\LH\SHFT-BOX
BRKT\LEGUME\RH\SHFT-BOX
HINGE\LEGUMEBOX
77/107
DRILLS
PARTS REFERENCE
97
98
77/107
DRILLS
PARTS REFERENCE
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
7A
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
8700004
8700005
8700006
6100046
4800127
8700007
8700008
8700009
8700010
3800082
1100224
1100232
8700011
6200010
1000112
2000703
2000002
8700012
8700013
1000111
2000016
1100233
4800013
4800153
5000023
5000022
4900003
4800029
5000019
4900002
5000001
8700014
8700015
8700016
1
1
2
2
6
2
1
1
1
2
2
1
1
4
2
4
2
1
1
1
2
1
8
10
12
18
18
2
2
2
10
4
2
2
Legume Box Weldment
Box Cover
Box Cover Spring Rod
Spring
Cotter Pin 1/8" x 1"
Shaft 3/8" Sq. x 50-3/4"
Bearing Right Hand
Bearing Left Hand
Sprocket 17 Tooth
Zerk 1/4" Tapper
40NP Pitch Connector Link
53 Links 40NP Pitch Chain
Shaft 1" x 29"
1/4" x 1" Key
4015 Sprocket 1" Bore 1/4 KW
2 Hole Flangette
1" Bearing with Lock Collar
Bracket Left Hand
Bracket Right Hand
4017 Sprocket 1" Bore 1/4 KW
Wood Block Idler
77 Links 40NP Pitch Chain
5/16" x 1" Hex Head Bolt
5/16" x 3/4" Carriage Bolt
5/16" Flat Washer
5/16" Lock Washer
5/16" Hex Nut
3/8" x 2-1/2" Hex Head Bolt
3/8" Lock Washer
3/8" Hex Nut
3/8" Flat Washer
Hinge
Seed Cup Long Gang (Not Shown)
Seed Cup Short Gang (Not Shown)
77/107
DRILLS
PARTS REFERENCE
99
S E E D I N D E X A S S E M B LY L E G U M E B O X
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
4800024
4800212
4800213
4800214
4900040
4900041
5000035
5000118
7500183
7500184
7500185
1
2
2
1
2
1
1
2
1
1
1
BOLT\HEX\1/4X3/4
PIN\RLLD\5/32X3/4
BOLT\CRG\1/4X1\NC
NUT\FLG\SERR\1/4\NC
NUT\WING\1/4\NC
WASH\FLAT\1/4
WASH\FLAT\SPCL\14MMX.5MMX20MMO.D.
METER\INDEX\SEED
SHFTR\INDEX\SEED
ARM\SHFTR\INDEX\SEED
NOT SHOWN
6500016
6500017
6500081
100
( D E TA I L C )
77/107
DRILLS
DECAL\INFO\CAL;SCALE;GRAIN
DECAL\INFO\CAL.SCALE;FERT
DECAL\INFO\CAL.SCALE;GRASS
PARTS REFERENCE
C U P A S S E M B LY L E G U M E B O X
ITEM
1
2
3
4
5
6
7
8
9
PART NO.
4800211
4900040
7500177
7500178
7500179
7500180
7500181
7500182
4800213
NOT SHOWN
3700129
77/107
DRILLS
QTY.
24
24
12
12
12
12
12
24
24
( D E TA I L D )
DESCRIPTION
SCR\SET\ALN\1/4X5/16\NC
NUT\FLG\SERR\1/4\NC
ROLLER\FEED
RING\SNAP
WASHER\ROLLER\FEED
FEED CUP ASSEMBLY
GATE\CUP\ASSY
CLLR\7/80D3/8SQ
HOSE\PVC\5/8IDX22-1/2\CLR
PARTS REFERENCE
101
L E G U M E D R O P T U B E A S S E M B LY
102
77/107
DRILLS
PARTS REFERENCE
L E G U M E D R O P T U B E A S S E M B LY
ITEM
PART NO.
QTY.
8400631
1
1A
1B
2
3
4
5
4800050
4800218
4900107
4800098
4900026
5000002
8400630
DESCRIPTION
TUBE\DROP\LEGUME\KIT\1BEND\107\PER ROW
1
1
2
2
1
1
PIN\COT\3/16 X 1-1/2
BOLT\HEX\5/8X5-1/2
NUT\NYLCK\5/8\NC
BOLT\HEX3/8 X 1-1/4\NC
NUT\JAM\3/8\NC
WASH\FLAT\5/8
BRKT\TUBE\DROP\LEGUME\1BEND\107
2 ft.
HOSE\PVC\5/8ID\CLEAR\BULK
NOT SHOWN
3700127
77/107
DRILLS
PARTS REFERENCE
103
LEGUME BOX MOUNTING BRACKET (77 & 107)
104
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
8700001
8700002
8700003
4800156
4800098
4800003
5000019
4900002
1
1
4
4
4
4
12
12
Mounting Bracket Left Hand
Mounting Bracket Right Hand (Not Shown)
Strap
3/8" x 1-1/4" Hex Head Bolt
3/8" Lock Washer
3/8" Hex Nut
77/107
DRILLS
PARTS REFERENCE
ACRE COUNTER (OPTION) (77 & 107)
Installation:
1. Turn acre counter into threaded hole
in end of acre counter shaft (see
Illustration).
77/107
DRILLS
PARTS REFERENCE
105
FA L S E B O T T O M O P T I O N ( 1 0 7 O N LY )
106
77/107
DRILLS
PARTS REFERENCE
FA L S E B O T T O M O P T I O N ( 1 0 7 O N LY )
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
8400244
8400318
8400319
8400320
8400321
8400322
8400323
8400324
7500308
4800164
5000001
5000019
4900002
1
2
1
1
1
1
1
1
2
40
54
54
14
Tank Weldment - 107
Divider Cover - 107
False Bottom RH - 107
False Bottom LH - 107
Side Seal Retainer RH - 107
Side Seal Retainer LH - 107
Upper Seal RH - 107
Upper Seal LH - 107
Rubber Seal
3/8" x 3/4" Hex Bolt
3/8" Flat Washer
3/8" Lock Washer
3/8" Hex Nut
77/107
DRILLS
PARTS REFERENCE
107
7 7 N AT I V E G R A S S K I T O P T I O N - A D D I T I O N A L A G I TAT O R S H A F T S
108
77/107
DRILLS
PARTS REFERENCE
7 7 N AT I V E G R A S S K I T O P T I O N - A D D I T I O N A L A G I TAT O R S H A F T S
ITEM
PART
QUANTITY
SINGLE
AGITATOR
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
3800082
4800012
4800044
4900076
5000001
5000027
7500107
7501058
8400256
8400257
8400259
8400260
8400261
8400267
8400396
8400397
8400423
8400659
8400708
8400710
8400711
8400713
2
4
4
8
1
2
4
8
4
8
2
4
10
10
2
4
12
12
0
12
2
2
2
0
0
2
4
4
6
6
6
6
1
2
EXISTING SHAFT
1
2
1
2
EXISTING SHAFT
EXISTING SHAFT
77/107
DRILLS
QUANTITY
DUAL
AGITATOR
DESCRIPTION
PIN\COT\5/16X1-1/2
NUT\FLG\SERR\3/8\NC
WASH\FLAT\3/8
WASH\7/8DX1-1/2OD\20GA SHIM
CLMP\HOSE
SUP\SHFT\ASSY\SLEEVE\107
SMALL AGITATOR PADDLE 7" SPACING
LARGE AGITATOR PADDLE 7" SPACING
BRKT\MNT\GRASS TUBE
BEARING SPACER PLATE
BRKT\MNT\GRASS TUBE
FNGR\AGTTR\DRILL
RUBBER PADDLE
PADDLE, REINFORCE PLATE
SHFT\TANK\33-1/16\DRILL
WHL\FEED\33-1/16\REAR\CTR
SHFT\TANK\23-15/16\DRILL
SHFT\TANK\19"\DRILL
WHL\FEED\23-15/16\REAR\RH
WHL\FEED\19\REAR\LH
PARTS REFERENCE
109
1 0 7 N AT I V E G R A S S K I T - A D D I T I O N A L A G I TAT O R S H A F T S
110
77/107
DRILLS
PARTS REFERENCE
1 0 7 N AT I V E G R A S S K I T - A D D I T I O N A L A G I TAT O R S H A F T S
ITEM
PART
2
2
3
4
5
6
7
7
8
8
9
9
10
10
11
12
13
14
15
16
17
18
19
20
21
21
22
22
23
24
25
26
27
28
29
30
31
32
33
34
NOT IN KIT
8400245
8400247
8400007
6100031
5000002
6100002
8400248
8400252
8400249
8400253
8400250
8400254
8400251
8400255
7500110
7500108
7500109
5000036
4800169
5000027
4800044
8400426
8400423
8400425
8400256
8400256
8400257
8400257
8400259
8400260
8400261
8400262
6500081
4800012
5000001
4900076
4800082
4900014
5000016
8400258
QUANTITY
SINGLE
AGITATOR
QUANTITY
DUAL
AGITATOR
1
1
3
3
3
5
1
1
1
1
1
1
1
1
3
3
3
3
1
2
1
1
1
1
18
12
1
1
3
3
3
5
1
1
1
1
1
1
1
1
6
6
6
6
2
4
2
2
2
2
18
12
17
11
3
3
3
3
1
1
18
18
18
8
8
13
1
1
1
12
12
12
8
8
13
DESCRIPTION1
GRAIN TANK
CONTROL PLATE 7” SPACING
CONTROL PLATE 8” SPACING
CONTROL PLATE GUIDE
SPRING\COMP\.072W\25/32OD\2-1/8
WASH\FLAT\5/8
SPRING\COMP\.072W\11/16OD\2-1/8
SEED CUP LEFT END SEC 7”
SEED CUP LEFT END SEC 10”
SEED CUP LEFT CEN SEC 7”
SEED CUP LEFT CEN SEC 10”
SEED CUP RIGHT CEN SEC 7”
SEED CUP RIGHT CEN SEC 10”
SEED CUP RIGHT END SEC 7”
SEED CUP RIGHT END SEC 10”
BRKT\CAST\W/BEARING/COMPLETE
CAST BRACKET HOUSING
1.445 5/8SQ HOLE SLEEVE
WASH\1-3/4ODX.89ID\1-1/4
PIN\RLLD\1/4X1-1/8
WASH\7/81DX1-1/2OD\20GA SHIM
PIN\COT\5/32X1-1/2
38-7/16 FEED SHAFT 100 SERIES
SMALL AGITATOR PADDLE 7” SPACING
SMALL AGITATOR PADDLE 10” SPACING
LARGE AGITATOR PADDLE 7” SPACING
LARGE AGITATOR PADDLE 10” SPACING
LOWER BEARING BRACKET
BEARING SPACER PLATE
UPPER BEARING BRACKET
SCALE PLATE
DECAL\INFO\CAL.SCALE\GRASS\107BOX
BOLT\CRG\3/8X1-1/4NC
WASH\FLAT\3/8
NUT\FLANGE\SERR\3/8\NC
BOLT\HEX\1/2X1-1/2
NUT\TPLCK\1/2/NC
WASH\FLAT\7/16
LARGE AGITATOR PADDLE, W/1 SHORT LEG
8400580
ATTACH\NTV-GRASS\KIT\107\7"\DEALER_INSTALLED
8400636
ATTACH\NTV-GRASS\ASSY\107\7"\FACTORY_INSTALLED
77/107
DRILLS
PARTS REFERENCE
111
1 0 7 N AT I V E G R A S S K I T - TA N K , E X I S T I N G S H A F T M O D I F I C AT I O N S
112
77/107
DRILLS
PARTS REFERENCE
1 0 7 N AT I V E G R A S S K I T - TA N K , E X I S T I N G S H A F T M O D I F I C AT I O N S
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
8400396
8400397
7500107
8400267
9
9
16
7
RUBBER PADDLE
PADDLE, REINFORCE P,LATE
CLAMP\HOSE\1-1/4\WORM\SS
FEED WHEEL SHAFT AGITATOR
77/107
DRILLS
PARTS REFERENCE
113
N AT I V E G R A S S K I T - TA N K E N D D R I V E A S S E M B LY ( 7 7 & 1 0 7 )
114
77/107
DRILLS
PARTS REFERENCE
N AT I V E G R A S S K I T - TA N K E N D D R I V E A S S E M B LY ( 7 7 & 1 0 7 )
ITEM
PART
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
29
1100236
1100237
1100227
2000016
8400240
8400241
8400242
2000802
8400070
8400438
1000029
1000175
8400243
8400246
6200014
8400239
8400238
4800167
4800034
4800003
4800029
5000019
5000001
4900002
4800514
8400074
30
30
8400573
8400738
QUANTITY
SINGLE
AGITATOR
QUANTITY
DUAL
AGITATOR
1
1
1
1
1
1
2
2
1
2
1
1
2
6
1
1
1
11
6
11
2
1
1
1
1
1
1
3
3
1
2
1
1
2
1
1
9
2
2
1
16
7
16
2
1
DESCRIPTION
CHAIN\50NP\75
CHAIN\50NP\95
CHAIN\50NP\CL
BLOCK\WOOD\IDLER
WOOD BLOCK IDLER MOUNT
MNT\SPKT\IDLER
TANK SEALER PLATE
CLLR\ECC\1-1/4
BRACKET W/BEARING
DRIVE SHAFT STUB(GRASS)
SPKT\50\B\14\1\1/4KW\HRN
SPKT\50\B\18\1\1/4KW
SHLD\AGTTR\SINGLE
SHLD\AGTTR\DOUBLE
KEY\SQ\1/4X1-1/4
SEALER PLATE & BRG COMPLETE
50-24 SPRKT W/SQ HOLE SLEEVE
SCR\CAP\ALN\3/8X1-1/4\NC
BOLT\HEX\3/8X1-1/2
BOLT\HEX\3/8X1
BOLT\HEX\3/8X2-1/2
WASH\LOCK\3/8
WASH\FLAT\3/8
NUT\HEX\3/8\NC
BOLT\HEX\3/8X2-3/4
SEALER PLATE
SHAFT\RD\TANK\1X38*
SHAFT\RD\TINTV_GR\1X23.5**
NOTE (*): REQUIRED WHEN THE NATIVE GRASS KIT AND A LEGUME BOX ARE MOUNTED
ON THE SAME 107
NOTE (**): REQUIRED WHEN THE NATIVE GRASS KIT AND A LEGUME BOX ARE MOUNTED
ON THE SAME 77
77/107
DRILLS
PARTS REFERENCE
115
N AT I V E G R A S S K I T - S E E D A N D F E R T I L I Z E R S E T T I N G A S S E M B LY ( 7 7 & 1 0 7 )
116
ITEM
PART NO.
QTY.
1
2
3
4
5
6
7
8
9
10
11
12
13
8400060
2000313
7500071
7500072
7500073
8400262
6500081
4800393
5000022
4900003
4800013
5000039
5000023
2
4
2
2
2
2
1
8
12
12
4
2
12
77/107
DRILLS
DESCRIPTION
CALIBRATION HANDLE
BRG\FLG\CAST\3/4\2 BOLT
CALIBRATION POINTER NUT
CALIBRATION CONTROL PL NUT
CALIBRATION SHAFT #6620
CALIBRATION SCALE PLATE
DECAL\INFO\CAL.SCALE\GRASS\107BOX
BOLT\HEX\5/16X7/8\GR8
WASH\LOCK\5/16
NUT\HEX\5/16\NC
BOLT\HEX\5/16X1
WASH\1-1/4ODX13/16IDX.110
WASH\FALT\5/16
PARTS REFERENCE
N AT I V E G R A S S K I T - D R O P T U B E A N D H O S E ( 7 7 & 1 0 7 )
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
4800014
4800071
4900002
4900003
5000019
5000022
5000023
7500168
7500169
8400236
8400285
1
1
2
1
2
1
1
1
1
1
1
BOLT\U\3/8X2X2-5/8
BOLT\HEX\5/16X1-1/4
NUT\HEX\3/8\NC
NUT\HEX\5/16\NC
WASH\LOCK\3/8
WASH\LOCK\5/16
WASH\FLAT\5/16
CONVOLUTED HOSE
CLAMP\SDHOSE\2\CP-34
STBLZR\TUBE\DROP
STBLZR\TUBE\DROP
77/107
DRILLS
PARTS REFERENCE
117
GAUGE WHEELS OPTION (77 & 107)
118
77/107
DRILLS
PARTS REFERENCE
GAUGE WHEELS
OPTION
(77 & 107)
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9 & 10
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
8400332
8400333
8400334
8400335
8400336
8400337
8400338
8400339
2600813
2600026
2600631
2900107
2900108
2900031
2900032
2900033
4800248
5000012
4900004
4800144
5000003
4900005
4800157
4900055
4800107
2500710
8400348
2
4
4
2
2
2
2
2
Gauge Wheel Mount Frame
Gauge Wheel Mount Strap
Bolt Sleeve
Wheel Folk
Spindle
Adjustment Handle
Short Spacer
Long Spacer
Tire & Rim Assembly
Tire 20.5 x 8.0 x 10
Wheel 10" - 5 Bolt
Hub (Complete Assembly) CMPT 5 Bolt
Hub CMPT 5 Bolt
Seal/Wheel Hub (R407)
Cone/Wheel Hub (44643)
Cup/Wheel Hub (44610)
3/4" x 6" Hex Bolt
3/4" Lock Washer
3/4" Nut
5/8" x 6-1/2" Hex Bolt
5/8" Lock Washer
5/8" Nut
3/16" x 2" Cotter Pin
1" Castle Nut
1/8" Hair Pin
1/2" - 2 60° Cone Wheel Nut
Gauge Wheel Kit Complete
77/107
DRILLS
2
2
2
2
4
4
4
4
4
4
8
8
8
2
2
2
10
PARTS REFERENCE
119
DRILL LIGHT KIT OPTION (77 & 107)
120
77/107
DRILLS
PARTS REFERENCE
DRILL LIGHT KIT OPTION (77 & 107)
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
5
6
4800277
4900009
5000024
5700423
8400040
8400702
8400739
8
8
8
2
1
1
4
BOLT\HEX\1/4X1
NUT\HEX\1/4\NC
WASH\LOCK\1/4
KIT\LIGHT
WALKWAY\100_SERIES
WALKWAY\77
PLT\MNT\LIGHT
77/107
DRILLS
PARTS REFERENCE
121
122
77/107
DRILLS
PARTS REFERENCE
77 / 107 DRILL Documentation Comment Form
DuraTech Industries welcomes your comments and suggestions regarding the quality
and usefulness of this manual. Your comments help us improve the documentation to
better meet your needs.
• Did you find any errors?
• Is the information clearly presented?
• Does the manual give you all the information you need to operate the equipment
safely and effectively?
• Are the diagrams and illustrations correct?
• Do you need more illustrations?
• What features do you like most about the manual? What features do you like least?
If you find errors or have specific suggestions, please note the topic, chapter and page
number.
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
__________________________________________________________________
Send your comments to:
DuraTech Industries International, Inc.
P.O. Box 1940
Jamestown, ND 58402-1940
OR
Contact us through our website: www.duratechindustries.net
Thank you for taking the time to help us improve our documentation.
77/107
DRILLS
PARTS REFERENCE
123