Fiche technique UT-6000 / Technical sheet UT-6000

Fiche technique UT‐6000 / Technical sheet UT‐6000 Applica on Résiden elle, Ins tu onnelle, Commerciale et Industrielle Residen al, Ins tu onnal, Commercial and Industrial Usage Moyen/Robuste—Medium/Heavy duty Norme / Standard Conforme—Complies with ANSI/BHMA A156.14 Grade 1 Fiche technique/ Technical sheet UT‐6000 Liste des pièces ensemble UT‐6000 / Parts list UT‐6000 Nom / Name Image / Picture Qté / Qty Montant d’acier Steel upright 4 Panneau de MDF MDF Board 1 1 Chariot UT‐2010 UT‐2010 Hanger 2 Plaque de fixa on Fixing plate 2 Support boi er de tête/Header bracket UT‐5030 2 Support de plancher Foot bracket 2 Guide décentré UT‐1050 Offset guide UT‐1050 2 Guide centré UT‐1055 UT‐1055 Center guide 2 Écrou hexagonal 5/16’’ 5/16’’ Hex nut 2 Rondelle d’espacement 5/16’’ 5/16’’ spacer washer 6 Rondelle de blocage dentée Tooth washer 8 Butoir UT‐5040 UT‐5040 door stop 1 Butoir UT‐DS200 UT‐DS200 Door stop 2 Vis auto‐perçante #10x2’’ Self‐drilling screw #10x2’’ 4 Vis HEX TEK #14x3/4’’ HEX TEK screw #14x3/4’’ 8 Vis auto‐perçante #10x1‐1/2’’ Self‐drilling screw #10x1‐1/2’’ 6 Vis #10x1‐1/4’’ Screw #10x1‐1/4’’ 13 Vis à gypse 1’’ 1’’ drywall screw 25 Vis #8x3/4’’ Screw #8x3/4’’ 7 Vis à tête plate #10x1‐3/4’’ Flathead screw #10x1‐3/4’’ 8 Roue pivotante UT‐2040 Spinwheel UT‐2040 2 Boulon en T T‐Bolt 2 Boi er de tête/Header track UT‐6000 Installa on Instruc ons for UT‐6000 Series Pocket Door
Hardware for 1‐3/8” and 1‐3/4” thick doors.
1‐Cut the header track to the required length. Required
length should be twice the width of the door minus 1/8”.
The opening width should correspond to twice the width
of the door plus 3/8”
2‐Mark the loca on of the header bracket UT‐5030 and
fix using #10 x 1‐1/4” screws. The height of the header
bracket should correspond to the height of the door plus
5‐1/16”.
3‐Slide hangers UT‐2010 into header track. Make sure
that hanger sleeve openings are accessible and on the
same side of the opening (facing the exterior).
4‐Insert one end of the header track into the header
bracket installed in step 2. Level the header track. A er
levelling, install second header bracket and screw it to
the stud using #10 x 1‐1/4” screws.
Installa on Instruc ons for UT‐6000 Series Pocket Door
Hardware for 1‐3/8” and 1‐3/4” thick doors.
5‐Using #14 x ¾” HEX TEK screws, secure header track to the
header brackets installed in step 2 and 4.
6‐Using a chalk line, draw a line on the floor of the opening
on either side of the studs. Next, refer to table 1 to deter‐
mine loca on of foot brackets UT‐5020 and fix using #8 x ¾”
screws.
Door width 2'‐0" (610mm) 2'‐2" (661mm) 2'‐4" (711mm) 2'‐6" (762mm) 2'‐8" (813mm) 2'‐10" (864mm) 3'‐0" (915mm) TABLE 1
1st bracket 2nd bracket 12‐7/16" (316mm) 13‐7/16" (341mm) 14‐7/16" (367mm) 16‐7/16" (418mm) 16‐7/16" (418mm) 18‐7/16" (468mm) 20‐7/16" (519mm) 24‐7/16" (621mm) 26‐7/16" (672mm) 28‐7/16" (722mm) 30‐7/16" (773mm) 32‐7/16" (824mm) 34‐7/16" (875mm) 36‐7/16" (926mm) 7‐Screw nylon guides onto the foot bracket located on
the side of the opening. Use the offset guides UT‐1050
for a 1‐3/4” door and the offset guides UT‐1055 for a 1‐
3/8” door.
8– Install steel uprights into the foot brackets. The oval
holes in the uprights must face the outside of the wall. To
facilitate the installa on of drywall, the seam on the side
of the uprights must be facing the back of the pocket.
9– Level the uprights and se‐
cure them to the header track
using toothed washers and
#14 x ¾” HEX TEK screws.
Installa on Instruc ons for UT‐6000 Series Pocket Door
Hardware for 1‐3/8” and 1‐3/4” thick doors.
10– Cut the MDF panel to the required length, which should be the door
width minus ¾”. Fasten it to the header track on the side of the opening sec‐
on using #10 x 1‐1/2” screws (3 per panel)
11a: Drill a 3/8” diameter hole at least 1‐1/2” deep at 3‐
1/2” from each edge of the door.
11b: Drill a 1/8” diameter hole at least 1” deep for the
fixing plates.
12‐Proceed with the assembly of the fixing plates as follows:
A: Take a T‐bolt, insert a toothed washer, two hex nuts, and then
another toothed washer.
B: Insert the fixing plate UT‐2020.
C: Insert the spinwheel UT‐2040.
13‐Align the fixing plate with holes drilled in step 3B. Screw on the
fixing plates using #10 x 1‐3/4” screws.
14‐Posi on the door under the hangers and insert the T‐bolts into
the sleeve openings.
15‐Set the door level and adjust its height by screwing or unscrewing
the spinwheel UT‐2040.
Installa on Instruc ons for UT‐6000 Series Pocket Door
Hardware for 1‐3/8” and 1‐3/4” thick doors.
16‐Set the door level and adjust its height by screwing or uns‐
crewing the hex part of the bolt. Once adjustment is made, lock the
bolt by ghtening the 5/16” hex nut.
17‐To avoid accidental door detachment, ghten the other 5/16”
hex nut against the hanger.
18– Install the stopper UT‐5040 to mid‐height of the stud at the back of
the pocket. When the door is in the open posi on, it will be cushioned by
the stopper. Depending on the type of trim used, it may be required to
shim the stopper with 3/16” washers.
19‐Slide the stopper UT‐DS200
into the rail at the desired stop
point and a ach to rail using #10
x 2” screws.
20– Complete the installa on by installing the drywall and mouldings. These items are supplied by others.
Parts list for UT‐6000 series:
Steel upright x4 MDF board x1 Header UT‐6000 HEX TEK screw #14x3/4’’ x8 5/16’’ Hex nut x4 T‐Bolt x2 3/16’’ spacer washer x6 Tooth washer x8 Offset guide UT‐1050 x2 Self‐drilling screw #10x1‐1/2’’ x6 Self‐drilling screw #10x2’’ x4 Hanger UT‐2010 x2 Center guide UT‐1055 x2 Screw #10x1‐1/4’’ x5 Fixing plate x2 Spinwheel UT‐2040 x2 Header bracket x2 UT‐5030 Floor bracker x2 Stop UT‐DS200 x2 Screw #8x3/4’’ x10 Drywall screw 1’’ x25 Flathead screw #10x1‐3/4’’ x8