Manual for local production and mounting of the

Manual for local production and mounting
of the exhibition “#enjoysweden”.
300x610mm
PRINTING THE PICTURES
178mm
200x200mm
Paper quality:
Somerset Photo 300 gram,
acid-free paper of 100% cotton.
Paper sheet format:
300 x 610 mm
Digital print format:
200 x 200 mm + logo and credit
Colours:
Image: CMYK
Logo and credit: 60% black
50mm
50mm
15mm
sandalen72
232mm
PRINTING AN INTRODUCTION
The first print in the exhibition should
be a short introduction text in the local
language.
1. Send translation and the embassy´s logo
to: oskar@ponnert.eu
2. Recieve a printable pdf with the correct
layout.
3. Print the pdf on the same paper format
and quality as the pictures.
MOUNTING
The #enjoysweden prints should always be hung in a way giving the impression of simplicity and lightness. Then off cours, mounting is depending on
the local conditions. Possibilities in the actual exhibition room is one thing.
Can we hung from ceiling or not? What materials are possible to purchase
locally, is another.
To make mounting as easy and flexible as possible, and to secure that every
presentation is done according to the intentions of the originators, we suggest three alternative design solutions:
Alt. 1: WIRE
Alt. 2: RAIL
Alt. 2: PIPE
MOUNTING OF WIRE (alternative 1)
With this solution you can hang the prints close to a wall or a window.
Material needed for 1 wire = 10 prints:
1x Dignitet - curtain wire set (a) - IKEA article number: 600.752.95
20x Riktig - curtain hook with clips (b) - IKEA article number: 802.122.01
(a)
(b)
MOUNTING OF WIRE (alternative 1)
INSTRUCTIONS:
1. Mount wire to wall.
Follow IKEA:s mounting instructions.
2. Hang 10 pictures on each wire
Wire length = 5m
3. Done!
MOUNTING OF RAIL (alternative 2)
With this solution you can hang the prints from the celing, freely in the room.
Material needed for 1 rail = 8 prints:
2x Thick fishing thread, 0,6 mm
2x Metal ring (key ring or similar)
2x Reinforcing bar, 2 m (a)
4x plastic tubes, 40mm
16x Riktig - curtain clip hook (b) - IKEA article number: 802.122.01
2x Riktig - curtain hook (c) - IKEA article number: 402.122.03
(a)
(b)
(c)
MOUNTING OF RAIL (alternative 2)
INSTRUCTIONS:
1. Fasten two fishing threads in the celing
Let them hang down to approx 2 m above floor level
Tie a ring at the ends.
2. Stretch two curtain hooks (c) to a W-shape
3. Hang the hooks in the rings
4. Hang the two reinforcing bars (a) between the
hooks.
5. Option: secure the rail´s ends with small plastic
tubes.
6. Hang 4+4 prints on the rail, using two clip hooks
(b) for each print.
7. Done!
MOUNTING OF PIPE (alternative 3)
With this solution you can hang the prints from the celing, freely in the room.
Material needed for 1 pipe = 10 prints:
2x Thick fishing thread, 0,6 mm
1x Steel pipe, approx diameter = 12 -16 mm, length = 2 m (a)
10x Ring clip hook (b)
(a)
(b)
MOUNTING OF PIPE (alternative 3)
INSTRUCTIONS:
1. Fasten two fishing threads in the celing.
Let them hang down to approx 2 m above floor level
2. Tie the steel pipe, make sure it´s horisontal.
3. Slide the ring clip hooks on to the pipe
5. Hang prints back-to-back in the same clip
7. Done!
DOCUMENTATION
This exhibition travels the world. It´s important for
both the initiators, SI and the photographers to get a
glimpse of when, where and how the prints are being shown, so make sure you photograph the local
installation and event and attach it to your evaluation
form after completed exhibition.
If any questions regarding the mounting or printing
of the exhibition, please contact: oskar@ponnert.eu
Any other questions regarding the project, please
contact: karin.karr@si.se
Thank you and good luck!