NANO Bautenschutz

NANO Technology Systems
“The Appliance of natures Science to the Creations of Mankind”
Building Protection
&
Anti-Graffiti Systems
eazY CLEAN
•Building & Monument Protection.
•Anti-Graffiti Systems
High Tech Protective Coatings
High Tech Coatings based on NANO
Technology for the Protection of building
Materials such as:
- Red Brick
- Fassade Brickwork
- Concrete
- Natural Stone
- Sandstone
- Plastered Walls
- Marble
- Wood
- Metal
WHY SURFACE PROTECTION USING
PRODUCTS BASED ON NANO TECHNOLOGY?
One of the most central and important themes in the Building Industry
throughout the world today is that of optimal Long Term protection of Buildings and
Building Materials through ecologically friendly and economical means.
One of the main reasons for early deterioration and thus the collapse of buildings and
building fascias, can be quite simply traced to the influence of water on the materials.
Water in Brickwork & Plaster becomes a means of transport for damaging materials such
as Sulphate and Chloride. The result is crystallisation („flowering“). Other damage is
caused by moss, Algae etc, which are all attracted by water or Damp. As one knows this
also leads to a large loss of heat and thus a lot more Energy is required.
eazY CLEAN Protective Coatings and special environmentally friendly cleaning materials
are the ideal solution to these problems.
The coated Substrate retains its natural diffusion even if coated on both sides, whilst at the
same time effectively resisting the penetration of water. Condensations which occur within
buildings are still able to disperse, quite naturally, through the coated surface – Harmful
Sulphates, Carbonates and Chlorides however are not!! The result is – Easy Cleaning,
Less use of water, Less Damage to Buildings, Energy Conversation, Time and Money is
saved, and above all the Environment remains intact!
EARLY PROTECTION USING
eazY CLEAN
Wood and Stone NANO PRODUCTS
Long term studies with Wood/Stone Protective
Coatings on Buildings have proven that water
intrusion which causes the illustrated damage can be
now be avoided. eazY CLEAN products provide
excellent Long Term protection against Ecological
influences and no damage is caused to the
Environment or the coated materials unlike
other products using silicones, teflons etc
NANO Technology is quite simply
“The Appliance of Natures Science to the Creations of Mankind”©
After application of the NANO Hydro- and Oleophobic Protective Coatings the Protective Qualities can be easily be
When water is sprayed on to coated materials the demonstrated.
result is a in most cases, a pearling effect almost the same as the
Lotus Leaf. One must also however bear in mind that this is not always the case – NANO Technology is not just
about the “pearling” or Lotus Effect – it is much, much more.
Silicones and Teflon's for example have initial effects that are also good however they tend to ”gas” after short
periods and dirt and grime bond themselves even more so than normal to surfaces and dirt and grime becomes
difficult to remove or requires the use of aggressive and environmentally damaging chemical cleaning materials. In
many cases using these methods, surfaces are also not able to diffuse or breath naturally as the pores are closed
off.
• Long Term Protection
•Natural dispersion (breathability) retained
•No changes in appearance
• Alcohol or Water Carrier disperses harmlessly in to atmosphere
•Long term, Water, Oil, Algae und Grime protection
•Less material
•Less Cleaning and after maintenance
•Less use of aggressive chemical cleaners
Problem:
Crystallisation („Flowering“) in Brickwork
With untreated Brickwork
Rain penetrates and
transports Sulphates &
Chlorides from inside the
Brickwork to the surface.
The result: These particles
dry and Crystalise or
“Flower“ on the surface and
start to cause damage to the
brickwork.
The Simple Answer –
NANO Technology Systems
Rain cannot penetrate the
surface. The water resistant
NANO Particles give long
term protection to the
coated surface
The material retains its
natural dispersion.
Condensations from within
the building are still able to
escape in the normal way
Brickwork Retains natural Diffusion!
Condensations from within
buildings are naturally released to
the outside. Loose Sulphates,
Chlorides and Carbonates stay
within the brickwork and thus
crystallisation reduced to absolute
minimum
Non Coated
Coated
Photo taken 3 days after application.
The Advantages of
Wood & Stone NANO Coatings
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
Strong hydrophobic & Oleo-phobic qualities
Long Term Dirt, Water and Oil Resistant .
Resists Weathering
Easy to Clean Effect
Resists the formation of Algae, Moss and Micro organisms
No difference in the Haptic (feel) or the Optic
100% Breathable (Diffusion Open)
UV Stable
Colour Neutral
Works even against Acids and Leaves etc
Permanent Protection even after several cleanings
Completely free from Tensides, Enzymes etc
Ecologically Friendly
Extremely Hard Wearing
Short Drying Time
Easy application via Spraying, Rolling or Painting – even children can apply it!
No Health Risks
Heat Resistant up to approx 250°C!
Withstands Long Term Regular Cleaning incl. use of High Pressure Systems with up to
approx 80 bar!!!
eazY CLEAN NANO
Wood & Stone Coatings
Stone and Wood Protective Coating is invisible, extremely hard wearing and Resistant to water-,
oil- and dirt particles. It is completely free from organic chemicals such as Tensides, Enzymes
etc. There are two main kinds of Wood
and Stone/Floor coatings. One water based coating
for Porous surfaces and
one alcohol based coating for non Porous weakly absorbent
surfaces. These Products can be applied to the surface of a huge variety of opened pored
mineral surfaces or non porous materials. Some examples are:
Cladding
Chalk
Concrete Walls
Concrete
Sandstone
Red Brick
Granite
Application Instructions
The Surface to be coated must be clean, dry and Fat Free. All Algae, Moss, Crystallisations
and any other dirt particles must be completely removed. We recommend the use of our
NANO Power Cleaner or our Wood and Stone Cleaner which is especially good for surfaces
already affected by black Algae & Moss.
We recommend the coating application be applied using an airless spray gun with a fine 1.0 or
1.3mm Jet. The Protective Coating material must be equally applied from the bottom to the
top. It can also be applied using a Hand Pressure (Garden Type) Sprayer. Whichever method
is chosen it is important to create a very fine coating on the surface.
To reduce the chance of „Overlapping“ the NANO Coating should be applied in one go. Once
the first coat is applied, it is recommend that a second coat be applied whilst the surface is
still damp (wet-in-wet system). It should then be left to cure for approximately 12-24 hours
depending upon humidity.
In the case of Non Porous surfaces, the coating must be applied in fine spray in order to
ensure there are no runs left on the coated substrate.
The surface drying time is approx 60 minutes at a temperature of +20°C. The complete curing
process takes approx 24 hours though the effects of the coating are immediately apparent
after surface drying . The application temperature should be between +5°C and +40°C.
IMPORTANT - DO NOT APPLY WHEN WET, IN RAIN!
Application Table
(All quantities of Material are approx)
Surface Type
Total Coatings Required
Approx Product
Requirements in
ml per m2
Marble
1–2
30 – 70
Granite
1–2
70 – 100
Brickwork & Fassades
1-2
100 – 120
Thicker Concrete
1-2
120 – 150
Opened Pored Concrete
1-2
100 – 180
Sandstone
1-2
150 – 240
Cleaning of Treated Services
The Real “WOW” effect!
Coated surfaces are extremely hard wearing and much easier to keep
clean. We recommend only water once a surface is coated however
should it be necessary to use a cleaner we recommend our NANO Bio
Cleaner Concentrate for the environmentally safe removal of any
stubborn particles.
Uncoated,
Uncleaned
Surface
Coated,
cleaned
surface
Length of Protection
Coated surfaces give long term Protection against Water, Oil and dirt Particles. The coating
undergoes an environmentally friendly chemical reaction when placed of the surface. The top
surface, once hardened out can only be removed by mechanical means (Heavy abrasion,
sanding etc). The coating, if applied correctly, will last for extremely long periods! Obviously
weather conditions, the amount of abrasiveness or mechanical pressures that are placed on the
coated material will all make a difference to the longevity of the coating! A coating for Porous
surfaces such as walls and roofs will last anywhere up to 5-10, perhaps even 15 years – the
pearling effect will disappear after approx. 1-2 years but the “easy to clean” /Anti Moss effect
remains. On a Non Porous surface or Floors it will generally last approx 3-5 years.
Coated
Uncoated
Graffiti-Protection Systems
NANO PAG WATER BASED!!!
This is absolutely new and completely revolutionary. It gives the ultimate
protection against Graffiti for all types of buildings.
It can be safely used on both the inside and outside of buildings. i.e.:
Schools, Rail Stations, Motorway Rest Areas, Football Stadiums, Bridges
etc, etc.
It will give long term protection to concrete, Plaster, Metal, Plastic, Wood,
Coursing Materials, Painted or varnished surfaces.
Advantages
● Once coated Graffiti can be easily removed 50-100 times using
only warm water and a High Pressure Hose – in extreme cases our
eazY CLEAN Graffitti Gel or Stripper Removers (depending upon
system used) can be applied
● Heat resistant from -40 °C to +100 °C
● Excellent resistance to mechanically abrasive and other cleaning
methods
● Surface retains natural disperson and thus allows condensations
from within to escape naturally
● UV-Resistant
ADVANTAGES
The durability and of the eazY Clean Graffiti System even under extremely
arduous conditions can be guaranteed to remain Stable for long Periods
● Between10-20 cleaning Procedures before a replacement of Coating is
necessary.
● No Colour changes even after 6 years of the Industrial FLORIDA Climate
Test Standard.
NANO PAG Protective Coating
WATER BASED
Application Instructions
Shake the bottle for approximately 2 Minutes.
The Protective Coating should be applied using a Spray System (1.0/1.3mm
Jet) or a Roller. A total of two coats should be applied.
A second coat should only be applied in a Wet/wet system one coat
horizontally, one coat vertically. The second coat should be applied after
the initial coat has had time to adhere but is still damp. The coating should
not be allowed to become wet during the 4-6 hrs thereafter – whilst the
protection is given after the 4-6 hrs full curing takes approx. 24 hrs.
Drying times:
Dosage:
1 h – Dust dry
50-100ml/m²
4 -6 h – Dry
12-24 h – fully cured
Outside and Building Temperature: +10 °C to +30 °C
Graffiti Removal
Graffiti Removal GEL
NOW WATER BASED!!
Graffiti removal utilising the Graffiti Gel:
The Intensive cleaner has been specially developed to ensure the complete removal of Spray
Paints, Felt Tip, Biro, Car and Special Paints.
Simply wipe or roll on the surface, if necessary use a scrubbing brush and a Cloth to remove the
Paint etc. Afterwards wash or hose down the wall with clean water.
This Product can be used on most Surfaces such as, Closed Concrete, Hard baked Building
brickwork, Tiles, Metal and Glass.
BE CAREFUL WITH PAINTED SURFACES – always try a small undisclosed area first.