iNexio IR Touch screen User Guide

Last update: 2010.01.15
iNexio IR Touch screen
User Guide
[Notes] The information in this manual is subject to change without prior notice, and images used in this
manual may differ from the actual image.
1
Contents
Chapter 1 Introduction of iNexio Touch Driver ....................................................................................................... 3
1.1 Introduction/Main Function.................................................................................................................................. 3
1.2 Specification................................................................................................................................................................. 4
Chapter 2 Installation & Running Program ............................................................................................................... 5
2.1 Cautions on Installation.......................................................................................................................................... 5
2.2 Recommended Specification ................................................................................................................................ 5
2.3 Program Installation ................................................................................................................................................. 6
2.4 Hardware Setup ....................................................................................................................................................... 14
2.5 Uninstall Program.................................................................................................................................................... 14
2.6 Program Start ............................................................................................................................................................ 16
Chapter 3 Touch Screen Info & Activity Setting ................................................................................................... 25
3.1 Browsing Information of Touch Screen ........................................................................................................ 25
3.2 Activity Mode Setup .............................................................................................................................................. 26
3.3 Multipoint Touch ..................................................................................................................................................... 29
3.4 Option/Tools.............................................................................................................................................................. 30
3.5 Popup control ........................................................................................................................................................... 37
3.6 Popup control ........................................................................................................................................................... 38
3.7 Multi Monitor Display ........................................................................................................................................... 39
3.8 Cautions on Multi Monitor Setting ................................................................................................................. 45
- APPENDIX -......................................................................................................................................................................... 46
APPENDIX 1 Caution on Windows 2000 .............................................................................................................. 46
APPENDIX 2 Cautions after Driver Installation .................................................................................................. 46
APPENDIX 3 Basic Gestures on Windows 7........................................................................................................ 47
APPENDIX 4 Gesture Supporting Programs ....................................................................................................... 48
Quick Guide ........................................................................................................................................................................... 50
2
Chapter 1 Introduction of iNexio Touch Software
1.1 Introduction/Main Function
iNexio Touch Driver is the software for the Infrared Touch Screen of Nexio Co., Ltd. It provides full
touch screen functionality for all software applications running under Microsoft Windows.
This version of iNexio Touch Driver software for your Nexio touch screen supports Serial, USB
controllers.
Once you install iNexio Touch Driver, you can select, launch, and drag objects using the touch screen.
To make a selection, you simply touch the screen. It’s that easy and natural – just touch to select.
iNexio Touch Driver Includes :
1.1.1 iNexio Touch Driver
iNexio Touch Driver is the software that the system uses to communicate with the touch screen.
The driver enables you to use the iNexio touch screen with applications running in Windows
environments. You can run Windows programs and use touch (finger or pen) input without any
program modifications.
1.1.2 Touch screen Control Panel
For example, you can define the following preferences:
• Whether the touch action occurs when you touch the screen or when you lift your finger (or pen)
off the screen
• Whether you hear a sound when you touch the screen
• How fast you need to touch to produce a double-click
• You can also use the control panel to calibrate the touch screen, to stabilize the cursor, and define
where the cursor appears relative to your touch (an offset)
1.1.3 Touch Click Control
Touch Click Control has the same function of Windows right mouse button. Any touch on the
monitor on which Right Button is running will produce a right button click.
1.1.4 Uninstalling iNexio Touch Driver
The Uninstall utility automatically deletes all iNexio Touch Driver components from your computer
and removes all iNexio entries from the system files.
3
1.2 Specification
1.2.1 OS Support
• Serial Touch
Windows 98, Windows NT, Windows 2000, Windows XP
[Notes] Serial Touch is supports Ver. 3.3.0.0 software only.
• USB Touch
-
32 Bit
Windows 2000, Windows XP, Windows Vista, Windows 7
-
64 Bit
Windows XP, Windows Vista, Windows 7
1.2.2 Number of Monitor Supported
• 2 monitors
1.2.3 Tablet PC and Windows 7 Compatibility
• The ‘Tablet PC Input Panel’ is not compatible with our Touch screen, but ‘On-screen keyboard’ is
working well.
• Panning with Inertia of the basic features on the Windows 7 gesture is working on the Internet
Explorer only.
4
Chapter 2 Installation & Running Program
2.1 Cautions on Installation
2.1.1 Keeping in storage
• Keep within the specified temperature and humidity range.
• Keep inside the packing box.
• Do not place under direct sun light.
2.1.2 Handling
• Do not put any objects on the products.
• Cables should not be folded.
• Use soft cloth when cleaning.
• Be careful not to let any liquid go inside the products.
2.1.3 Assembly
• Do not force in excess when assembling. Distortion might cause malfunction.
• In case of using extension cable, electric power hub or repeater should be used at every
connection of 5M.
• Do not use screw that is longer than 4mm on the mounting hole of rear cover. Or it might
damage PCB inside.
2.2 Recommended Specification
2.2.1 PC Specification
• IBM PC Compatible
• Intel Celeron 1.6 GHz CPU
(For Multi-point Touch screen - Core2 Duo 1.7 GHz CPU are recommended)
• Minimum 1 GB memory
• Microsoft Windows 2000, Windows XP, Windows Vista, Windows 7
• 6 MB free disk space
2.2.2 Installation
• The Installation way is based on Windows XP.
• Driver version is changeable.
5
2.3 Program Installation
Follow the below installation way, and connect (Plug-In) USB or Serial cable to PC.
2.3.1 Running program
2.3.1.1 Auto Execution
• Will open below window when inserted setup CD then select [Install] to start installation.
6
[Notes] Windows Vista
• Select “Run nxTConAutoRun.exe” in the AutoPlay window after inserting CD.
• Select proper OS version. Click [Continue] in “User Account Control” window.
[Notes] Windows 7
• Select “Run nxTConAutoRun.exe” in the AutoPlay window after inserting CD.
• Select proper OS version. Click [Yes] in “User Account Control” window.
7
2.3.1.2 Manual Execution
1. Select [My Computer] icon at Desktop or Start menu.
2. Select “DVD or CD-ROM” Driver on “My Computer” window by inserted Nexio Driver setup CD.
8
3. Execute [nxTConAutoRun.exe] on “DVD or CD-ROM” Driver.
9
2.3.2 Installation
2.3.2.1 Start Installation
Click [Next]
2.3.2.2 License Agreement
If you want to keep progress after reading the License Agreement, Select “I accept the terms of
license agreement”, click [Next].
10
2.3.2.3 Selecting Destination Folder
Click [Browse] to designate the folder, Click [Next]
2.3.2.4 Selecting Program Folder
After selecting the program folder, click [Next]
11
2.3.2.5 Files Copy
Click [Next] and files copy starts.
12
2.3.2.6 Complete Installation
1. Remove ‘NEXIO setup CD-ROM’ from drive, when the below window appears.
2. Select
“Yes, I want to restart my computer now.
3. Click [Finish] to restart PC. (Recommended)
13
2.4 Hardware Setup
2.4.1 Hardware Auto Installation
2.4.1.1 Hardware Connection
Plug-in Touch Screen to PC ports after restart your system.
Hardware installations will automatically when notifications on taskbar as below appear.
2.5 Uninstall Program
1. Click “Uninstall iNexio Touch Driver” at start menu
14
2. Click [Yes]
3. Uninstall in progress
4. Select “Yes, I want to restart my computer now.” Click [Finish] to restart PC (Recommended)
15
2.6 Program Start
2.6.1 Execute on Windows XP
Click “iNexio Driver” icon on screen or “iNexio Touch Driver” at start menu to run the driver program
16
2.6.2 Execute on Windows Vista & 7
Windows Vista adds UAC (User Account Control) security function. UAC prevents access to security
area.
User have to run iNexio Driver by “Run as administrator” or disable UAC function to set the driver
value.
2.6.2.1 Execute on Windows Vista
1. Click right button of mouse after selecting the iNexio Driver icon on screen or iNexio Touch
Driver at start menu to select “Run as administrator”
17
2. Click right button of mouse after selecting the iNexio Driver icon on screen. Select “Properties”
-> “Compatibility”, check “Run this program as an administrator”, Click “Show settings for all
users”
Click [Continue] when User Account Control window appears
Check “Run this program as an administrator”, click [OK]
18
3. Click [Start] and run control panel. Select “User Accounts and Family Safety”
[Notes] Not Recommended
Select “User Accounts”
19
Select “Turn User Account Control on or off.”
Click [Continue] when User Account Control window appears.
Uncheck “Use User Account Control (UAC) to help protect your computer”, click [OK] and restart
PC.
20
2.6.2.2 Execute on Windows 7
1. Click right button of mouse after selecting the iNexio Driver icon on screen or iNexio Touch
Driver at start menu to select “Run as administrator”.
2. Click right button of mouse after selecting the iNexio Driver icon on screen. Select “Properties”
-> “Compatibility”, check “Run this program as an administrator”, Click “Show settings for all
users”.
21
Check “Run this program as an administrator”, click [OK]
3. Click [Start] and run control panel.
Select
“User Accounts and Family safety”
[Notes] Not Recommended
22
Select “User Accounts”
Select “Change User Account Control settings”
23
Click or drag control bar at “Never Notify” on “User Account Control Settings”, click [OK]
Click [Yes] when “User Account Control” window appears
24
Chapter 3 Touch Screen Info & Activity Setting
3.1 Browsing Information of Touch Screen
Port No., Firmware version, Device Name, Comm. Device and information will appear after click “Scan”
25
3.2 Activity Mode Setup
3.2.1 Sound effect
No Sound
No Sound
Touch down
Sound when you touch Down
Lift up
Sound when you Lift Up
No Sound
No sound on any touch activity.
Touch down
Beep sounds as soon as finger or pen touch on the screen.
Lift up
Beep sounds when finger or pen is lifted up from the touch screen.
[Notes]
PC must have Beep speaker. (Refer to Motherboard manufacturer or reseller)
Beep sound does not support on Windows 64 Bit OS and Windows 7.
26
3.2.2 Sound tone/Sound frequency
The frequency (Tone) and the Duration of the sound can be adjusted by moving the appropriate
slider with the touch screen or mouse, or by using the keyboard arrow keys.
3.2.3 Double click speed/Touch area
Define how fast you need to touch and the space in which you must touch in order to produce a
double-click.
3.2.4 Double click Test
Enables you to test the double-click speed and area.
3.2.5 Touch action
Drawing Mode
Drawing mode can be used for graphic application program. It is as same as when user press and
lift button.
Non-Filter
Drawing speed is fast..
Filter
Drawing is soft.
Touch Only Mode
Drawing or dragging is not supported in this mode.
27
23.2.6 Touch rotation
In case of putting the touch screen not properly on the display, you can select proper degree to
adjust the touch (cursor) position. You have to adjust Calibration after setting the Rotation.
• 0 degree
Default setting (Landscape)
• Left 90 degree
Rotate 90 degree to left direction (Portrait)
• 180 degree
Rotate 180 degree to right direction
• Right 90 degree
Rotate 90 degree to right direction
• Mirror Vertical
Opposite side of up and down
• Mirror Horizontal
Opposite side of left and right
[Notes]
In case of multi-monitor mode that apply Touch rotation value to all monitors at the same time.
3.2.7 Factory reset
Reset all the value as of factory setting. However, the value of Touch Device Monitor Mapping is not
changed.
28
3.3 Multipoint Touch
3.3.1 Enable mouse action
As a Basic option, touch action can be recognized on all windows programs. By disabling this option,
the touch is no longer recognized on all windows program. You can also use the Popup Control
Menu (Refer to the page 53) to enable the function again.
3.3.2 Enable gesture action
This option makes Gesture Function available. It is operated at Drawing Mode only. Please refer to
the 3.2.5 Touch Action for setting Drawing Mode. Please refer to the Appendix 2 Basic Gestures
on Windows 7 for Gesture Action.
3.3.3 Enable multi-touch limit
The size of a touch object can be adjusted in connection with 3.3.3.1 X-width limit.
Allow XY range
Recognized within the size of X Y limit
Limit XY range
Recognized without the size of X Y limit
3.3.3.1 X - width limit
iNexio Touch Driver has the area recognition function on Single &Multi point touch. With X-Width
Limit/Y-Width Limit function, the size of a touch object can be adjusted on X
Y limit in
connection with 3.3.3.1 X-width limit. (Refer to the 3.4.3.3 Multitouch view)
3.3.4 Multipoint Reset
XY range setting on Multipoint Touch can be initialized
29
3.4 Option/Tools
3.4.1 Right Click Tool
The left button is activated
The right button is activated
3.4.1.1 Use Right Click Tool
1. The left mouse button active
When the left button is shaded on a small window on the desktop, the touch active on mouse
is same function as the left button of mouse. Any touch on the desktop or an application will
produce a left button click consistent with the button settings in the control panel.
2. The right mouse button active
When the right button is shaded on a small window on the desktop, the touch active on mouse
is same function as the right button of mouse. Any touch on the desktop or an application will
produce a right button click consistent with the button settings in the control panel.
30
3.4.2 Touch calibration
Calibration process is running automatically based on the resolution. If the screen is not calibrated,
the active area or the touch screen may not be aligned properly or may be unnecessarily small in
size. Therefore, you need to calibrate as the following picture. Once calibrated, the information of
calibration is saved by the touch screen for each video solution. So, you do not need to calibrate
any more.
However, you need to calibrate when you change a PC. For more accuracy, follow the below
instruction and also refer to the 3.4.4 Fine coordinate Correction - offset and 3.4.5 Fine
coordinate Correction – zoom.
3.4.2.1 Calibration
1. As you click the [Calibration], the circle targets appear on the screen.
2. Position your finger or pen to the center of the circle.
3. Repeat for additional calibration targets.
4. If you accidentally touched the screen in the wrong place during the calibration, you will distort
the touch screen calibration. Test to make sure you are satisfied with the calibration results.
3.4.2.2 Auto Calibration
As you click the [Auto Calibration], calibration process is running automatically based on the
resolution. This mode is possible to make a touch when the size of touch screen is only same as
the size of panel.
31
[Notes] Aspect Ratio Control (ARC) function
In case of change aspect ratio to 4:3 -> 16:9 or 16:9 -> 4:3, after changed aspect ratio then
always adjust active area with touch screen are same aspect ratio as manual calibration. (Refer to
the 3.4.2.1 Calibration)
32
3.4.3 Drawing test tool
3.4.3.1 Single touch test
The below picture are shown when you click the [Single Touch Test] button and test with your
finger on the touch screen (This program is for Drawing Test purpose and be available in Drawing
mode only)
3.4.3.2 Multi touch test
The below picture are shown when you click the [Multi Touch Test] button and test with your
fingers or palms simultaneously on the touch screen.
The below picture show simple contents developed by Nexio applying Multi-Point Touch. The part
of cognition and multi-points are shown in red circle when touching. You can test with the 3.3.3.1
X – width limit option of object size limit.
33
3.4.3.3 Multitouch view
The below picture are shown when you click the [Multi touch View] button and you can test with
your fingers or palms simultaneously on the touch screen.
These contents are reference to the contents developer with API (Application Program Interface)
as the test shows the area of LED sensors that are recognized upon touch.
[Notes] Additional Information on Multitouch view
As the below picture shows, there are virtual mages beside the real touch points, when fingers are
positioned at different X or Y coordinates. These virtual images are moving in a regulation
according to the real touch point. The contents developer, therefore, should refer to this virtual
image regulation.
34
[Notes] Additional Information on Multi touch test and view
As the above picture shows on multi-point touch test, when touch points area at the same axis of
X or Y coordinates, the second touch points is not shown. This is purposely programmed not to
recognize the second touch point in these contents. But as the below picture shows on 3.4.3.3
Multitouch view contents, the second touch is shown even at the same axis of X or Y coordinates
35
3.4.4 Fine coordinate correction - offset
After you calibrate the touch screen, the cursor should be located directly underneath your finger
when you touch the screen. However, you may prefer to offset the cursor slightly above your touch
so that you can see the cursor and point more easily and precisely to small objects. Fine Coordinate
Correction option lets you define the distance between your fingertip and the position of the cursor
on the screen. Offsetting the cursor is helpful when selecting small items, such as single letters in
word processing, check boxes, or radio buttons. Click [Up] [Down] [Left] [Right] to make X or Y offset.
3.4.5 Fine coordinate correction - zoom
Sometimes the screen image extends beyond the edge of the monitor bezel. In these cases, It may
be difficult to touch items at the left and right edges of the screen. Normally monitor has auto
scaling function itself. This function is required to adjust the auto scaled image for more accuracy.
Click [X Zoom –(or+)] [Y Zoom –(or +)] to adjust the screen image.
3.4.6 Point compensation
Due to specific character of Touch screen, it is difficult or not possible to touch on the edge of
monitor screen. By activating this option, even the edge can be touched as the option automatically
extends the touch coordinates.
36
3.5 Popup control
3.5.1 Popup control START/STOP
• START
Start Popup Control Menu
• STOP
Stop Popup Control Menu
3.5.2 Popup activate area
The Popup Control Menu appears on the screen when you touch your finger or any objects on the
marked position and remove after the fixed time at the Popup Activate Time.
3.5.3 Area allow percent
Specifying the area where you touch your finger or any objects to bring the Popup Control Menu up.
3.5.4 Popup activate time
Setting the time to bring the Popup Control Menu up.
37
3.6 Popup control
3.6.1 Disable Mouse Action
Touch action is not recognized on all programs on the screen. By re-click, the option is back to the
basic function.
3.6.2 Enable Touch Area Limit
The size of a touch object can be adjusted on X Y limit.
(Refer to 3.3.3.1 X - width limit).
3.6.3 Open Touch Control Panel
Touch Control Panel is appeared.
3.6.4 Exit
Popup Control Menu is closed.
38
3.7 Multi Monitor Display
Multi monitor supports two monitors.
Check “Support Multiple monitors” and set Clone, Independent, Stretch (Horizontal, Vertical) mode
based on graphic card.
3.7.1 Touch devices monitor mapping
Click [Mapping>>] to set each touch screen on each monitor
3.7.1.1 Sequence of mapping to monitor
1. Select the first touch screen as below
[Notes]
You must restart nxTCon program. In case of
attaching or removing the Touch screen from PC,
Touch devices monitor mapping list is not
updating automatically.
39
2. When you click the [Mapping>>], you can see the below the picture.
[Notes] Display00 is the number 1 monitor, while Display01 is number 2 monitor.
3. Display00 is selected as the number 1 monitor by double click for the first selected touch
screen.
4. Second touch screen is selected as below.
5. After click the [Mapping>>], display01 is selected as the number 2 monitor by double click for
the second selected touch screen.
40
3.7.2 Select active monitor
Select the touch screen for applying Option/Tools
3.7.2.1 How to select active monitor
1. As you select the Display00, the setting value of Option/Tools are applied with the touch screen
of the number 1 monitor.
2. As you selected the Display01, the setting value of Option/Tools is applied with the touch
screen of the number 2 monitor.
41
3.7.2.2 Active Monitor Calibration
1. Calibration
On the Independent and Stretch mode (Refer to 3.7.3 Multi-monitor Mode), number 1 and
number 2 monitors are connected with each touch screen. When you select Display00 on Select
Active Monitor, the calibration screen of number 1 is running and the X, Y coordinates are
adjusted.
When you select Display01 on Select Active Monitor, the calibration screen of number 2 monitor is
running and the X, Y coordinates are adjusted.
42
2. Auto Calibration
On the Independent and Stretch mode (Refer to 3.7.3 Multi-monitor Mode), when you select
Display00 on Select Active Monitor, X, Y coordinates on number 1 monitor are automatically
adjusted. When you select Display01 on select Active Monitor, X, Y coordinates on number 2 are
automatically adjusted.
43
3.7.3 Multi-monitor mode
[Notes] The image used in these contents appears when the multi display setting of graphic card
changes.
3.7.3.1 Clone mode
In the clone mode, one of the monitor is selected as the primary one. All other monitors usually
have the same image as the primary monitor. The touch screen on each monitor functions as
clone mode too.
3.7.3.2 Independent mode
In the independent mode, all screen show same image and the touch screen on each monitor
functions independently.
[Notes] If touch point is recognized by only one monitor, please refer to the Multi Monitor Display
at 3.7.2 Select active monitor and set again.
44
3.7.3.3 Stretch mode
The stretch mode makes all screens combine for a single image, in this mode the touch screen on
each monitor functions independently.
[Notes] It may not support stretch mode on different kind of VGA model.
3.8 Cautions on Multi Monitor Setting
3.8.1 Sequence of Setting
1. If Nexio program is open, should be close the program.
2. Setting up resolution for each of the monitors on your VGA card.
3. Could find Clone, Independent, Stretch (Span) or Clone, Independent mode on Display Properties.
Select what you want out of modes.
3.8.2 Check Display Properties
The standard number 1 monitor is always located at left or up-left on Multi-Monitor setting.
45
- APPENDIX APPENDIX 1 Caution on Windows 2000
If the USB cable is not removed after uninstall the driver, “Unsafe Removal of Device” window appears
as below. This is warning message because the device is recognized as “Unplugged” by automatic
reset function as there is no signal though still connected. To avoid this on Windows 2000, you have
to remove the USB cable after uninstalling driver.
APPENDIX 2 Cautions after Driver Installation
• If Touch screen is not working well after driver installation, please remove USB cable and reconnect
again.
• In case of using 2 or more USB interface Touch screen, other Touch screen might not working for
some time when USB cable of the other Touch screen is disconnected.
46
APPENDIX 3 Basic Gestures on Windows 7
[Notes] The gesture enabled Touch screen function.
1. Execute iNexio Driver program.
2. Move to Multipoint Touch tap, check on Enable gesture action.
3. Move to Setup tap, select Drawing mode, click apply button.
47
APPENDIX 4 Gesture Supporting Programs
Gesture
Support Programs
Tap/Double Tap
All programs
Panning with Inertia
Internet Explorer only
Selection/Drag
All programs
Press and Tap
All programs
Windows Explorer, Internet Explorer (upper v7.0)
Zoom
Windows Photo Viewer, Google Earth (upper v5.1)
Microsoft Products
Rotate
Windows Photo Viewer, Google Earth (upper v5.1)
Two-Finger Tap
N/A
Press and Hold
All programs
Windows Explorer
Flicks
Internet Explorer (upper v7.0)
Windows Photo Viewer
Microsoft Products
48
2. Hardware Setting & Driver Install
Quick Guide
① After restart PC, connect (Plug-In) Touch Screen cable to PC port
* Multi monitor
nxTCon is the software for the Infrared Touch Screen of Nexio Co., Ltd. It provides full touch screen function for all
software applications running under Microsoft Windows.
■ nxTCon Program Advantages
■ System Requirements.
• Enables to set either touch mode and drawing mode
• Enables to set touch rotation based on the angle of
the screen.
<Rear View>
• Minimum Intel Celeron 1.6GHz CPU, 1G RAM
(For Multi-point, Intel Core2 DUO 1.7GHz CPU are recommended)
• USB 2.0
• Provides the function of calibration and adjustment of
touch point (cursor).
<Driver Install on Windows 2000/XP/Vista/7>
② Hardware installations will automatically when notifications on taskbar as below appear.
• Windows 2000/XP/Vista/7 (supports USB Touch)
• Number of monitor supported : 2 monitors
• Provides the function of multi monitor mode.
(clone, independent and stretch mode)
• Provides the function of right mouse click.
■ Uninstall nxTCon
■ nxTCon Install
<Driver Uninstall on Windows 2000/XP>
1. Start -> Program -> iNexio -> Select “Uninstall nxTCon” to remove program.
1. Running Install Program
① Install program starts by Autorun function when inserts CD. Select [Install] to start installation.
② “InstallShield Wizard for iNexio IR Touch Driver”, click [Next]
③ “License Agreement”, click [Yes]
④ “Choose Destination Location”, click [Next]
⑤ “Select Program Folder”, click [Next]
⑥ “Start Copying Files”, click [Next]
⑦ “Setup Status”
⑧ Select “Yes, I want to restart my computer now”, and restart PC.
<Driver Uninstall on Windows Vista/7>
1. Start -> All Program -> iNexio -> Select “Uninstall nxTCon” to remove program.
①
⑤
②
③
④
⑥
⑦
⑧
• Due to UAC (User Account Control) function on Vista OS, 1)
• In case of using extension cable, electric power hub or
process is required or 2) should be set when running nxTCon.
repeater should be used at every connection of 5M.
1) Click right mouse button after selecting driver icon, click “Run
• The driver for suitable OS should be installed.
as administrator”
• Remove USB cable and restart PC when install or uninstall
2) Click right mouse button after selecting driver icon, go to
nxTCon. It might not work properly without restarting PC. After
Properties->Compatibility->check
restarting PC, connect USB cable.
administrator”, Click “Show settings for all users”
• Windows XP 64bit/Vista 64bit/7 32bit/7 64bit does not support
• Back to factory default setting, go to Setup tab, click “Factory
Beep sound.
• 2 monitors are supported as Multi monitor.
“Run
this
program
as
an
Reset”
• Please visit http://www.inexio.co.kr for downloading updated driver.