schilder systeme

Transcription

schilder systeme

place picture here
Jürgen Schilder , Thorsten Reibel – ABB Stotz-Kontakt GmbH, Heidelberg
March 2014
ABB STOTZ-KONTAKT GmbH
ABB i-bus® KNX
Webinar “i-bus® Tool”
i-bus® Tool – a professional Service Tool
Overview
© ABB
26.02.2015 DESTO Jürgen Schilder | 2

New and innovative software concept
made by ABB

It supports system integrators during
commissioning and service

Internal information and states of the
device hardware and software
applications are now available in a
transparent manner

The i-bus® Tool is optional, i.e. the ABB
i-bus® KNX devices must still be
commissioned using just the ETS

An important principle is that no
divergences to the ETS project can
result through the i-bus® Tool
Overview
Power Supply Diagnosis SV/S
© ABB

The i-bus® Tool accesses an ABB i-bus®
KNX device via a standard KNX
interface (USB, IP) with the assistance
of the physical address

When the i-bus Tool is connected to a
KNX device, the device-specific plug-in
displays the functions that are possible
for this device type

The system integrator can trigger the
desired functions, read values, simulate
states and make settings for the
connected device (e.g. scenes)

The information from status bytes can,
for example, be represented as plain
text
Overview
Blind/Roller Shutter Actuator JRA/S
© ABB

Functions are only available if they have
been enabled in the ETS

Disabled functions are greyed out or not
visible

No assignment of group addresses
required

If it is not possible to execute a function,
the parameterization in the ETS should
be checked

If the KNX interface is still used by
another application (e.g. ETS), it may be
necessary to end this first

The i-bus® Tool is free-of-charge

System requirements: Windows from XP
(32, 64 bit)
Additional new features
DALI-Software-Tool inside

© ABB
The DALI Tool is mandatory for setting up the KNX DALI devices

Addressing DALI devices, e.g. ballasts, dimmers

Assignment of the DALI devices into DALI groups

Display of all lamp and ballast faults

Commissioning of constant light control (DALI Light Controller)
Additional new features
IP Discover Tool (former IP-Firmware Tool)

All discovered KNX IP devices are displayed

If one or several devices are selected, with the control buttons in the
menu bar different actions can be performed (open website, blink LED
and restart device)
OFF!!!
Hint:
A virus scanner or firewall can
block the IP communication!
© ABB
Additional features
Demo Modus

The demo mode shows the functionality of the i-bus® Tool without
connection to the KNX bus

A device must be selected and by clicking "Demo" the plugin of the
device is displayed

This is only for demonstration purposes, there is no functionality
available and the tool is not connected to the KNX bus
© ABB
Additional features
Help Menu

© ABB
The Help button opens a context-sensitive help menu
Supported devices
Currently, the following devices are supported (March 2014)

DALI Gateway: DG/S 1.1, DG/S 1.16.1 and DGN/S 1.16.1

DALI Light Controller: DLR/A 4.8.1.1 and DLR/S 8.16.1M

Light Controller: LR/S x.16.1

Energy Actuator and Module: SE/S 3.16.1 and EM/S 3.16.1

Blind/Roller Shutter Actuators: JRA/Sx.y.z.1

Line Coupler: LK/S 4.2

Power Supply Diagnosis: SV/S 30.320.2.1 and SV/S 30.640.5.1
… and new devices are added continuously
Hint: Not all former application or firmware versions
can be supported (e.g. DALI Gateway)
© ABB
Overview
First steps
© ABB

Download and install i-bus® Tool

Adjust the settings

Select the KNX interface

Check for updates

Connect to a KNX device via the
physical address

Test the ETS parameters, functions,
read values, simulate states and make
settings (e.g. scene values)

If necessary change ETS parameter,
download the application and check
again via the i-bus® Tool
Installation

Download the i-bus Tool (www.abb.com/KNX ~4 MB)

Extract the file (self extracting ZIP-file)

Double click the file „ibusTool.exe“

Installation routine will be started

Agree to the “Licence Agreement for use of Software”
© ABB
Main menu

© ABB
This window is displayed after starting the i-bus® Tool
Adjust the settings

Refresh display, number of telegrams, automatic disconnect

Language

German (DE)
English (EN)
French (FR)

Spanish (SP)
Italian (IT)
Russian (RU)

Dutch (NL)
Polish (PL)
Additional bus traffic !!!
© ABB
Select KNX interface

After the i-bus® Tool has been successfully started, the KNX interface
must be selected

This can be undertaken via “Settings” (ETS connection manager)

If a KNX interface is already parameterized, this can be selected
directly via the item “Connect” (main menu)
© ABB
Main menu

© ABB
Connect the i-bus® Tool to a KNX device
Connection to a device

In this window a connection to a KNX device can be established

With „Scan“ the i-bus® Tool searches for devices in programming mode
© ABB
Connected to a device

When the i-bus® Tool is connected to a device, the "Display mode" is
active (all active buttons are disabled)

Changing to "Configuration mode" can be done with the control button
"Select configuration mode“ (send commands to the device)
Display mode
© ABB
Configuration mode

© ABB
Pages per device: General, channel, groups, …

© ABB
More details per device
DALI Gateway DG/S 1.1
© ABB
DALI Gateway DG/S 1.1
re-addressing of a
DALI device can
be done by drag
and drop
© ABB
DALI Gateway DG/S 1.16.1
© ABB
re-addressing of a
DALI device can
be done by drag
and drop
© ABB
© ABB
DALI Gateway DGN/S 1.16.1
© ABB
© ABB
© ABB
DALI Light Controller DLR/S 8.16.1M
© ABB
© ABB
© ABB
Light Controller LR/S
© ABB
Light Controller LR/S
© ABB
Blind/Roller Shutter Actuators: JRA/S
© ABB
Line Coupler LK/S 4.2
© ABB
Line Coupler LK/S 4.2
© ABB
Power Supply Diagnosis SV/S
© ABB
Energy Actuator SE/S and Energy Module EM/S
© ABB
Energy Actuator SE/S and Energy Module EM/S
© ABB

schilder systeme

Transcription

Similar documents

Measurement and Automation Systems

ABB Malaysia`s

ABB Automation and Power World Australia 23

ABB powers the Gautrain express

Wapice - Cleantech Kvarken

CLASH 2011 presented by Relentless 20 – 22 May Skatehalle

Pressed to perfection

Martin Hale ABB Product Group EV Charging Infrastructure