basic training

Transcription

basic training

RA
T
C
I
S
BA
G
N
I
IN
This presentation explains the technical basis for highefficiency filtration and then explores the fundamentals of
Pulmonary Function Testing, the procedure for which our
PFT Filters are used, and also describes the technical
details of the Westmed BlockAide™ PFT filters.
by Michael McPeck, RRT FAARC Director, Clinical Educa1on Westmed, Inc. mmcpeck@westmedinc.com 516.729.9989 Copyright © 2014 Westmed, Inc. All Rights Reserved
What is a filter?
Copyright © 2014 Westmed, Inc. All Rights Reserved
Filter defined
Filtration
…the process of separating the components of a fluid “stream.” The components may be the ingredients of the stream or accidental contaminants that need to be removed to purify the stream. The fluid “stream” can be a liquid or a gas.
The two main types of filtration are:
•  particulate
•  gas phase
In most medical applications, we are concerned with
particulates or “patient droplets.”
What is efficiency?
Efficiency is the expression of a filter’s ability to
to perform filtration, or to trap and remove components of a certain size from the stream. Efficiency is expressed mathematically as …
Output divided by Input:
Efficiency = Output Input Copyright © 2014 Westmed, Inc. All Rights Reserved
Mechanisms of particle capture
There are five primary mechanisms by which filtration of particles occurs …
Inertial impaction – the particle’s forward
inertia slams it into the filter media.
Diffusion – exceptionally small particles
“drift” into the media by Brownian motion.
Interception – the particle has too little
forward inertia for impaction but not enough
to completely bypass the media.
Sieving – the most commonly perceived
mechanism; the particle is too large to pass
through “pores” in the media.
Electrostatic attraction – differences in
electric charge create attraction of the
particle to the media. This may be used
in conjunction with the other mechanisms
to enhance them.
How is filter efficiency determined?
Filters are challenged with 0.3 µμM (micron) particles in order to analyze the percentage of particles that have been retained. Why 0.3 µμM ?
For a variety of physical reasons, the 0.2 to 0.3 µM diameter particle is the
most difficult to filter. For that reason, 0.3 µM has been termed the “MPPS,”
Most Penetrable Particle Size and has become the standard by which
filters are tested for efficiency.
What does HEPA mean?
HEPA is the acronym for …
High Efficiency Particulate Air
So, going back to the definitions, we see that a HEPA filter is concerned with particulates and a gas stream (air) …
… and it is especially concerned with efficiency.
HEPA defined
High-Efficiency Particulate Air or High-Efficiency Particulate Absorption
HEPA is a type of air filter. Filters meeting the HEPA standard have many applications, including use in medical facilities and equipment, automobiles, aircraft, and homes. The filter must satisfy certain standards of efficiency such as those set by the United States Department of Energy (DOE). To qualify as HEPA by US government standards, an air filter must remove (from the air that passes through) 99.97% of particles that have a size of 0.3 µμM or larger. A filter that is qualified as HEPA is also subject to interior classifications.
99.97% Efficient @ 0.3 µM
HEPA defined
High-Efficiency Particulate Air or High-Efficiency Particulate Absorption
HEPA media is similar to blo[ing paper, and made of a matrix of very thin, r a n d o m l y a r r a n g e d overlapping fibers that create a tortuous pathway. The airflow pathway is made even more tortuous by pleating the media. polyester glass fibers plea1ng Copyright © 2014 Westmed, Inc. All Rights Reserved
Electrostatic Filters
In electrostatic filters, 50% of the fibers are positively charged, and 50% negatively charged. Particles and droplets tend to carry either a positive or negative electrostatic charge. So, roughly half of the negative particles will be a[racted to positive fibers and vice versa. Upon reaching the fibers particles are held in place by the electrostatic charge. The electrostatic mechanism is utilized to enhance the fundamental physical particle capture mechanisms.
Nega1ve ( -‐ ) Par1cle Posi1ve ( + ) Fiber Electrosta1c par1cle aFrac1on mechanism Copyright © 2014 Westmed, Inc. All Rights Reserved
Electrostatic Filters
Electrostatic filters are nearly as good as HEPA filters and are used in some similar applications where airflow resistance and resistance to we[ing may be critical factors.
Features:
•  Open structure
•  Larger pore size
•  Electrostatically charged polypropylene fibers
•  Lower airflow resistance
•  Lower weight
•  Failsafe hydrophobic mechanism (does not absorb water)
•  Tend to be sold at lower price than HEPA
•  Media of choice in global market for respiratory applications
99.9% Efficient @ 0.3 µM
Electrostatic vs HEPA
Theoretical mean efficiencies predicted for electrostatic and HEPA filters based upon challenge with 0.3 µμM test particles. Electrosta?c HEPA 10 10,000 3 10,000 99.9 % Efficient
99.97 % Efficient
10 particles / 10,000
3 particles / 10,000
How small/large is a micron (µμM)?
Can you really appreciate how small 1 micron actually is? 2.5 microns (µμM) (average aerosol particle created by nebulizer) 1 micron (µμM)
Human Hair
How small/large is a micron (µμM)?
Can you really appreciate how small 1 micron actually is? Relative Sizes
•  Filters are challenged with 0.3 µμM spherical particles.
•  P. aeruginosa is a rod, ~1 to 5 X 0.5 to 1 µμM.
•  M. tuberculosis is a rod, ~2 to 4 X 0.2 to 0.4 µμM. 1 micron (µμM)
Human Hair
Purpose of the PFT filter
PFT filters serve one purpose: to protect the patient from inhaling micro-‐‑organisms and aerosols from the PFT equipment, and to keep aerosols and droplets containing micro-‐‑organisms from entering the PFT equipment.
Morgan PFT filter shown
However, they must do their job without inhibiting flowrates or
causing high resistance or creating a gas leak in the PFT system.
Electrostatic vs HEPA for PFTs
For Pulmonary Function Testing, electrostatic filters are preferred for the 3 principle reasons:
•  Lower resistance than HEPA filters
•  Be[er moisture resistance
•  Lower cost than HEPA filters. Use of an electrostatic filter instead of a HEPA filter allows for the manufacture of an effective filter, with airflow resistance as low as possible, at a cost acceptable to the market.
Use of an electrostatic filter instead of a HEPA filter does not increase either the machine contamination risk or the patient infection risk
because: (1)  the theoretical efficiencies between the devices are statistically similar, and (2)  particles encountered in pulmonary function testing are almost always large “patient droplets,” many microns in size, not individual microorganisms.*
* Microorganisms do not exist in free form, they are aFached to, or a part of, some suitable substrate that tends to form larger droplets or par1cles. Copyright © 2014 Westmed, Inc. All Rights Reserved
Westmed BlockAide™ PFT Filters
The sales flyer is very important because, in addition to describing the product, it also contains important specifications to help match the correct filter to the wide variety of PFT devices currently in use.
Elliptical vs Round
Pulmonary function labs often like to have different shapes of mouthpieces available to accommodate patient preferences. Some patients, particularly children, have small mouths and therefore tend to do be[er with the elliptical mouthpiece. Studies where high expiratory flowrates are anticipated (spirometry and
flow/volume loops) require filter mouthpieces with large inside diameters
that do not impose high resistance or impede the flow.
Flanged vs Straight
Rubber flanged mouthpieces that fit in the mouth with the flange situated between the lips and the gums tend to do a be[er job of making a gas-‐‑tight seal for tests that require a long breathing period, such as gas dilution lung volumes and diffusing capacity. They are also useful for plethysmography where the flange helps hold the mouthpiece in place during the panting breathing technique. Straight mouthpieces are more frequently used for spirometry procedures where forced expiratory flowrates are very high.
Morgan PFT filter shown
Be aware that our mouthpieces are cost-effective substitutes for OEM filters (shown here)
and can be used either with or without a flanged rubber mouthpiece.
Basic Specifications
Common customer questions might include:
• What is the filter efficiency?
• What is the filter resistance to flow?
• What is the filter deadspace?
Filter Efficiency
A common customer question might be: What is the filter efficiency?
Efficiency is the expression of a filter’s ability to perform filtration, or to trap and remove components of a certain size from the stream. Efficiency is expressed mathematically as …
Output divided by Input:
Efficiency = Output
Input
The Westmed BlockAide™ PFT Filter
has an bacterial/viral efficiency of
99.9% of particles 0.3 µM in size.
0.3 µM is the industry standard test
size for filters because 0.3 µM
represents the MPPS, or
Most Penetrable Particle Size.
Resistance to Flow
A common customer question might be: What is the filter resistance to flow?
How is filter resistance determined? Very simply, a number of samples of filters are tested to determine their pressure drop (△P) at many different flowrates across their expected range of use. One way of doing this would be to subject the filter to increasing flowrates at 1 L/sec increments, up to a maximum of 14 L/sec, and then measuring the △P at each flowrate. The resulting data set might look like the table on the left below. Next, the data would be plo[ed in a spreadsheet to create a graph showing the data points on the chart on the right, below. Finally, the equation for the slope of the △P /Flowrate line is solved by linear regression
to reveal the filter resistance (y); in this case, 0.46 cmH2O/L/sec.
Resistance to Flow
A common customer question might be: What is the filter resistance to flow?
Our filter resistance specification, 0.46 cmH2O/L/sec indicates that, for every 1 L/sec of increasing flowrate, the pressure drop (△P) across the filter increases by 0.46 cmH2O. The spec also indicates that the filter was tested up to a maximum flowrate of 14 L/sec which is slightly more than we would expect even the healthiest patient to achieve.
Deadspace
A common customer question might be: What is the filter deadspace?
“Deadspace” is simply the amount of gas-‐‑containing volume enclosed within the body of the filter. Obviously, the larger the filter, the greater the deadspace. Deadspace is important because it often represents the amount of exhaled CO2-‐‑containing “rebreathed volume” that a patient may have to inhale when a[ached to an apparatus through a filter. The smaller the patient, the smaller the tidal volume and, hence, the more critical that deadspace becomes.
Round = 54 mL Ellip?cal = 51 mL Some degree of deadspace is
unavoidable because of the large
diameters that are required to reduce
airflow resistance. However, the shape of
our PFT filter is designed specifically to
reduce deadspace as much as possible
while maintain the requisite diameter for
low flow resistance.
Connector Sizes
Inside (ID) &Outside (OD) Filter
Diameters in millimeters (mm)
One way of selecting the correct
filter would be to match the
inside and outside diameter of
the PFT machine-side of the filter
to the actual diameter on the
mouthpiece port of the PFT
machine or device.
Connector Sizes
Another way of selecting the
correct filter would be to look up
the brand and model of the PFT
device on the chart on the flyer.
Sizes given are in millimeters (mm).
Conclusion
• 
The American Thoracic Society (ATS), issues clinical practice guidelines that are widely accepted by pulmonary practitioners and manufacturers of pulmonary diagnostic equipment. ATS has specified a maximum allowable PFT filter resistance of 1.5 cmH2O/L/sec. Obviously, the Westmed Blockaide™ PFT Filters, at 0.46 cmH2O/L/sec, are well below that maximum. • 
Statements by other manufacturers of filters, especially by the companies that make the PFT equipment, that suggest our filter resistance is too high, or that the high limit is impractical for pediatric patients, are merely sales tactics that are designed to confuse the customer and cast doubt on the quality of our filter. They are trying to sell their filters, with a high markup, but which are no be[er than ours.
• 
The fact is the Westmed Blockaide™ PFT filters are high quality filters that are well within the maximum resistance specified by the ATS. The high testing limit of 14 L/sec is assurance that the filter resistance is linear up to that value; it does not affect whether or not the filter can be used on pediatric patients. It can.

basic training

Transcription

Similar documents

Transtar Presentation SPX

StrionAir Design System

Filtration

compact wheel loaders

Global Pattern Analysis and Classification of Dermoscopic Images Using Textons

KAF Bernoulli - Krone Filter

Clean Better, Live Smarter

Alpha Cell E HEPA - Flanders Corporation

CamelPhat Manual 20120117.indd

PLM9000E-12000E-15000E manual.indd

Quality Check Factsheet - Prime Focus Technologies

PLM9000E-12000E-15000E manual.indd

General Catalog of Air-Conditioning Products

CamelSpace Manual 20110117.indd

Automatic detection of human nudes

PDF File