Section A - DeVilbiss

Transcription

ITW DeVilbiss Table of Contents
Spray Guns-Packages-Accessories
Maximum Performer Features and Benefits .................................................................. 1
JGHV Standard Size .................................................................................................... 2
JGA-HVLP Suction Feed .............................................................................................. 3
MSV Mid-Size .............................................................................................................. 4
TGHV Detail/Touch-Up ................................................................................................. 5
GFG-HVLP Gravity Feed .............................................................................................. 6
GTiTMMillennium/Suction Feed ..................................................................................... 7
EXL HVLP Pressure Feed Spray Gun ........................................................................... 8
EXL HVLP Suction Feed Spray Gun ............................................................................. 8
EXL HVLP Gravity Feed Gun ........................................................................................ 9
EXL SRi HVLP Spray Gun ............................................................................................ 9
FinishLine Gravity and Suction Feed .......................................................................... 10
VTZ HVLP Spray Gun ................................................................................................ 11
EGHV Touch-Up Maximum Performer ........................................................................ 12
Air Cap & Tip Selection Chart ................................................................................ 13-14
Air Cap Test Kits ........................................................................................................ 15
MBC-510 Manual Spray Gun ...................................................................................... 16
JGA-Plus Standard Size Manual Spray Gun .......................................................... 17-18
MSA Mid-Size Manual Spray Gun .............................................................................. 19
EGA Touch-Up Manual Spray Gun .............................................................................. 20
Other Equipment and Accessories ............................................................................. 21
Spray Equipment Packages .................................................................................. 22-23
Solvent SaversTM Hose/Gun Cleaners ......................................................................... 24
Fluid Strainers and Equipment ................................................................................... 24
Selecting Air Cap, Fluid Tip and Needle ...................................................................... 25
Air Cap Selection Guid ............................................................................................... 26
Fluid Tip and Needle Selection Guide ......................................................................... 27
Tanks and Cups
DeVilbiss Tank/Binks Tank Crossover Chart (cont’) .................................................... 28
Pressure and Suction Feed Cups ............................................................................... 29
KB Series Pressure Feed Cups ................................................................................. 30
Clean Air Filtration-Accessories
Centrifugal Filter-Regulator Units ................................................................................ 31
Coalescer Filter-Regulator Units ............................................................................ 32-34
Three-Stage Desiccant Unit ........................................................................................ 36
Whirl-Wind In-Line Filter ............................................................................................. 36
CleanAir Air Regulators .............................................................................................. 36
Air Control Accessories .............................................................................................. 37
Air VizorTM ......................................................................................................... 38-39
Order Toll-Free 800-365-7565
Govt. Purchase Cards Accepted
Maximum Performer Features and Benefits
Durability
3
1 300-grade stainless steel fluid
passages offer waterborne
compatibility, corrosion resistance
and protection from harsh,
self-etching primers.
• Dual-seal fluid inlet assures a
positive seal.
Lightweight and precisionbalanced for operator comfort.
• Maximum Performer spray
guns are sized to fit both the
operator and the application,
with standard-size, mid-size
and detail/ touch-up models.
4
Replaceable anodized aluminum
baffle with air cap retaining ring
threads eliminates the need to
replace the gun body should
threads become damaged.
5
Redesigned trigger strike pad
makes trigger action smoother
and extends air valve life.
• Cartridge-type air valve is
designed for positive sealing
and quick triggering action.
• All gun components have been
life cycle tested to ensure
reliability in production
environments.
2 Drop forged aluminum gun bodies
are strong, durable and light
weight.
4
6
6
2
7
9
5
3
1
7
8
8
9
Maintenance
• Simple, straightforward design for
easy care and maintenance.
• Economical replacement parts are
available and easy to install.
10
Performance
GoldMax™ air caps and special
fluid tip, needle and baffle
combinations provide
unparalleled atomization.
• Collectively, Maximum
Performer spray guns can
handle more than 90% of the
materials and coatings being
applied today, including higher
solids materials and higher fluid
flows.
Long-life needle packings require
fewer adjustments.
Easy to Use
Light trigger action for easy
operation and comfort.
Knurled knobs for easy adjust
ment of pattern and fluid
flow.
1/4" air inlet connects to any
standard compressor system.
10
1
JGHV Standard-Size Maximum Performer
Our JGHV Standard-Size Maximum
Performer manual spray gun gives you
the best of everything -- the comfortable
fit and feel of DeVilbiss’ classic JGA
spray gun combined with the high
transfer efficiency and superior
atomization of HVLP.
• 300-grade stainless steel fluid
passages for waterborne
compatibility.
Productivity and Finish
Quality
The productivity and finish quality
of any Maximum Performer spray gun is
determined by the air cap and fluid tip
combination.
Ordering Information
The JGHV Standard-Size Maximum
Performer manual spray gun is available
with the following air cap and fluid tip
set-ups, factory assembled for immediate
delivery.
Part No.
JGHV-531-28FF* JGHV-531-46FX
JGHV-531-28FX* JGHV-531-3-46FF**
JGHV-531-33FF* JGHV-531-3-46FX**
JGHV-531-33FX* JGHV-531-83D
JGHV-531-46FF* JGHV-531-83E
*Standard tips and needles are 400-grade
stainless steel
**Includes 300-grade stainless steel with
U.H.M.W. polyethylene seat in fluid tips.
When ordering DeVilbiss spray guns, the part
number includes information on the specific
gun model, air cap and fluid tip you will
receive.
Example: JGHV-531Fluid Tip Size
Air Cap Number
Basic Gun Model
Accessories
•
•
Technical Specifications
The versatile JGHV gun delivers a high
quality finish with less overspray than
conventional guns.
Body:
Drop forged aluminum
Weight:
20.8 oz (599 gr)
Air Inlet:
1/4” NPS (M)
Fluid Inlet:
3/8” NPS (M)
Fluid Passages:
Stainless steel
Feed Type:
Pressure feed
Service Bulletin:
SB-2-246
Gun Repair Kit:
KK-4987-2
Note: JGHV-531-46FF has been tested and verified in U.S.E.P.A. Environmental
verfication program under contract #DAAE30-98-C-1050 with the U.S. Army
(TACOM-ARDEC) via EPA Inter-Agency Agreement #DW97936814.
See WWW.EPA.GOV/ETV
2
•
Remote Cups
Two-quart remote cups are available
in aluminum (KB-555) or stainless
steel (KB-545-SS).
Attached Cups
One-quart attached cups are available in aluminum with Teflon®
lining (TLC-576) or stainless steel
(TSC-591).
Note: KK-4980 regulator control
kit is required for use with these
cups and must be ordered separately.
Additional Accessories
Hose assemblies, air control
regulators, air cap test kits, gun and
hose cleaning equipment and other
accessories also are available.
Note: JGHV-531-46FF
NSN#4940-01-315-8352
JGA-HVLP Suction Feed
Classic Series Spray Gun
Quality
of any Classic Series spray gun is
combination.
The Classic Series JGA-HVLP
suction feed spray gun is available
with the following air cap and fluid
tip set-ups, factory-assembled for
immediate delivery. Standard tip
and needle are 400-grade stainless
steel.
Part No.
JGA-510-57D*
JGA-510-57DE*
* Cup not included. Order separately.
When ordering DeVilbiss spray
guns, the part number includes
information on the specific gun model,
air cap and fluid tip you will receive.
Body:
Weight (Less Cup): 21.4 oz (608 gr)
Air Inlet:
1/4" NPS (M)
Fluid Inlet:
3/8" NPS (M)
Fluid Passages:300 grade stainless steel
Feed Type:
Suction feed
Service Bulletin:
SB-2-248
Gun Repair Kit:
KK-4987-2
Accessories
• One-quart paint cups available in
Teflon®-lined aluminum (TLC-555),
aluminum (TGC-545) and stainless
steel (TSC-595).
• One-pint aluminum cup (TGC-536)
is also available.
• Hose assemblies, air control
regulators, gun and hose cleaning
equipment and other accessories
also are available.
Example: JGA-510Fluid Tip Size
The JGA-HVLP suction feed spray
gun offers easy-to-use suction feed
operation with the high transfer
efficiency of HVLP. That means you
get the flow rates and uniform spray
patterns you want using conventional
suction feed fluid delivery.
Air Cap Number
Basic Gun
Model
and protection from harsh
JGA-HVLP suction feed provides high
quality atomization with the high
transfer efficiency of HVLP.
Five Easy Ways to Order from Fluid-Air Products Inc.
CALL
MAIL
Toll-Free
your order
800-365-7565 12834 Gravois Rd.
to order
St. Louis, MO 63127
FAX
your order
314-729-7099
E-MAIL
your order
info@fluidair.com
WEBSITE
Visit our site
www.fluidair.com
and link to
www.gsa.gov
for on-line ordering
3
TM
MSV Mid-Size Maximum Performer
Manual HVLP Spray Gun
Our MSV Mid-Size Maximum
Performer spray gun delivers the same
high transfer efficiency and superior
performance as the standard-sized
model, only in a smaller package.
Weighing only 17 ounces, the
Mid-Size Maximum Performer spray
gun is lighter, and it helps reduce
operator fatigue while providing
excellent comfort and control.
compatibility.
Quality
The productivity and finish quality of
any Maximum Performer spray gun is
combination.
The MSV Mid-Size Maximum Performer
manual spray gun is available with the
following air cap and fluid tip set-ups,
factory assembled for immediate delivery.
Part No.
MSV-531-28FF*
MSV-531-28FX *
MSV-531-33FF*
MSV-531-33FX *
MSV-531-46FF*
MSV-531-46FX *
MSV-531-83D
MSV-531-83E
MSV-531-3-28FF**
MSV-531-3-28FX **
MSV-531-3-46FF**
MSV-531-3-46FX **
* Standard tips and needles are 400-grade
stainless steel. 300-grade tips and needles
(MSV-531-3) should be used for materials
with pH less than 7.
** Includes 300-grade stainless steel with
U.H.M.W. polyethylene seat in fluid tip.
When ordering DeVilbiss spray guns,
the part number includes information
on the specific gun model, air cap and
fluid tip you will receive.
Example: MSV-531-
Body:
Weight:
17 oz (476 gr)
Air Inlet:
1/4" NPS (M)
Fluid Inlet:
3/8" NPS (M)
Fluid Passages:
Stainless steel
Feed Type:
Pressure feed
Service Bulletin:
SB-2-243
Gun Repair Kit:
KK-4987-2
Fluid Tip Size
Air Cap Number
Basic Gun Model
w/400 gr. stainless fluid tip, needle
The lightweight MSV spray gun is
designed for maximum operator
comfort.
Accessories
•
•
•
4
Remote Cups
Two-quart remote cups are
available in aluminum (KB-555)
or stainless steel (KB-545-SS).
Attached Cups
One-quart attached cups are
available in aluminum with
Teflon® lining (TLC-576) or
stainless steel (TSC-591).
Note: KK-4980 regulator control
kit is required for use with these
cups and must be ordered
separately.
regulators, air cap test kits, gun and
hose cleaning equipment and other
TM
TGHV Detail/Touch-Up Maximum Performer
Manual HVLP Spray Gun
Our versatile, new TGHV Detail/
Touch-Up Maximum Performer spray
gun offers superior atomization at the
tip, combined with the comfort benefits
of a lightweight, pistol-grip design, side
port fluid inlet for gravity, and standard
bottom inlet for pressure/suction feed.
Requiring low air cap pressure, our
TGHV spray gun provides the control
needed for detail, repair, shading and
highlighting operations. Depending on
the type of feed used, an adjustable
spray pattern from 5" to less than 1/4"
round makes the TGHV ideal for
applications requiring focused spray
patterns, such as automotive OEM spot
repair, final repair, as well as mask
spraying in furniture manufacturing,
plastic decorating, and other
applications requiring small defined
patterns or mask spraying.
• Side port gravity feed with smaller
front end for better operator
visibility to the spray target.
compatibility.
• All TGHV series guns utilize
many of the same high quality
components as DeVilbiss JGA,
JGV, MSA, and MSV spray guns.
Quality
of any Maximum Performer spray gun
is determined by the air cap and fluid
tip combination.
The TGHV Spray Gun is available
in both gravity feed and pressure/
suction feed models.
• Model TGHV-530 Pressure/
Suction Feed Spray Gun.
• Model TGHV-635 Gravity Feed
Spray Gun with Cups (2 1/2 oz.
and 8 oz. cups included.)
The TGHV Detail/Touch-Up Maximum
Performer manual spray gun is available in
the following models, factory assembled for
immediate delivery.
Part No.
TGHV-530-Pressure/Suction Feed*
TGHV-635-Gravity Feed*
* Standard tips and needles are 300-grade
stainless steel (F) .041".
Body:
Weight:
19oz. (530g) TGHV-530
24.5oz.(690g)TGHV-635
with 8 oz. cup 22.4 (635g)
with 2.5 oz. cup
Air Inlet:
1/4" NPS(M)
Fluid Inlet:
3/8"NPS(M)-TGHV-530
1/4"NPS(M)-TGHV-635
Fluid Passages:
300-grade stainless steel
Air Consumption:
6.7 SCFM @ 10 psi air
cap
Air Requirements: 35 psi inlet=10 psi cap pressure
Service Bulletin:
SB-2-192
Gun Repair Kit:
KK-5048
TGHV Accessories
• RemoteCups
Two-quart remote cup is available in
aluminum (KB-555) or stainless
steel (KB-545-SS).
• Gravity Cups
2 1/2 oz. (TGHV-407-K10) pkg. of
10, 8 oz. (KGP-509-1).
• Additional Accessories
Hose assemblies, air cap test kit, gun
and hose cleaning equipment and
other accessories are also available.
TGHV-635 Gravity Feed
Supplied with 8 oz.
TGHV-415 SS cup
5
GFG-HVLP Gravity Feed
Classic Series Spray Gun
•
•
•
300-grade stainless steel fluid
Standard equipment includes 20 oz.
nylon cup and booth-mount gun
hook.
Drip check in the cup lid prevents
leaks and spills from vent hole.
Body:
Weight (Gun & Cup):
27 oz (768gr)
Air Inlet:
1/4” NPS (M)
Fluid Inlet:
3/8” BSP (F)
Fluid Passages:
300 grade stainless
steel
Feed Type:
Gravity feed
Service Bulletin:
SB-2-169
Gun Repair Kit:
KK-5025
Accessories
Productivity and Finish Quality
of any Classic Series spray gun is
combination.
When your application calls for
higher transfer efficiency, but you need
more control of the fluid output than you
would get with a suction feed gun,
choose the GFG-HVLP gravity feed
spray gun. Combining the quality and
performance of HLVP technology with
the advantages of gravity feed fluid
flow, the GFG-HVLP spray gun assures
virtually every drop in the cup is used,
so there’s no waste. Clean-up is quick
and simple, too.
With gravity feed, atmospheric
pressure and gravity itself force the
newer, higher solids materials into the
fluid passage, making the gun more
efficient than suction feed. Less air cap
pressure is required, too.
6
Classic Series GFG-HVLP gravity
feed spray guns are available with the
following air cap and fluid tip set-ups,
factory-assembled for immediate
delivery. A new 20 oz. acetal gravity cup
is included. Standard tip and needle are
400-grade stainless steel.
•
•
•
•
8 oz. nylon cup (KGP-510-1).
32 oz. aluminum cup (GFC-502).
Workbench gun holder (GH-505)
holds the gun upright to facilitate
filling.
regulators, gun and hose cleaning
equipment and other accessories
also are available.
Part No.
GFG-618-57DFF
GFG-618-57DFW
When ordering Devilbiss spray guns, the
part number includes information on the
specific gun mode, air cap and fluid tip
you will receive.
Example: GFG-618
For smaller production jobs, GFG-HVLP
provides the quality and performance of HLVP
technology with the advantages of gravity fluid
flow.
Fluid Tip Size
Air Cap Number
Basic Gun Model
(including cup)
GTiTM
Millennium
Te
Se ste
e d/V
W e
W rif
W ied
.E
PA ET
.G V/E
O P
V. A
ET
V
GTiTM
Compliant HVLP
Suction Feed
Precision engineered #2000 gold air cap - meets
exacting performance demands, producing an extremely
fine finish with all materials. Developed in conjunction
with top American and European automotive paint
companies to spray the latest materials.
Optimum atomization for clearcoats and single stages
Produces high gloss finish and minimizes orange peel.
Excellent fluid control for applying more film build with
fewer passes.
Lightweight and comfortable. Classic JGA fit and feel,
yet lighter weight. Gun body styling changes for
improved comfort
Easy to clean - Plated gun body is gun washer safe and
maintains its “like new” appearance.
Quick cleanup and upside-down spraying (with no
cup lid leaks) - with E-Z LinerTM disposable cup liners.
GTi Millennium HVLP Spray Gun includes: 1.3mm,
1.4 mm, and 1.5 mm fluid tips; 32 oz. aluminum cup
(120175/GFC-502) with push on lid; air adjusting valve
with gauge (180006/HAV-01); air cap cleaning kit, spray
lube, fluid filter, gun hook; (9) E-Z Liner disposable
liners (190966/OMX-70-K48)
Fluid
Tip (mm)
170156
1.3 & 1.4
GTI-620G
(includes 1.3 & 1.4 mm
and 1.5 mm fluid tips)
1.5
Inlet Air
Pressure
Applications
20-25 psi
25-30 psi
Base coats
High solids clear coats
and single stages
20-25 psi
25-30 psi
Base coats
Low solids, clear
coats, single stages
and waterbornes
Waterborne compatible - stainless steel fluid tip and
needle, electroless nickel-plated gun body inside and
out.
Lightweight and comfortable - familiar JGA fit and
feel, yet 24% lighter.
Accurate, repeatable settings - pointers on fluid
and fan controls.
Virtually maintenance-free! - No gaskets,
self-sealing.
Simple, easy-to-use suction feed operation allows
painters to spray with the method they’re used to.
GTi suction feed gun includes:
TGC one quart-cup
Air adjusting valve with gauge.
GTi Compliant Suction Feed
Order No.
Model No.
170146
GTI-600S
GTi Millennium Gravity Feed
Order No.
Model No.
Fluid
Tip (mm)
Inlet Air
Pressure
2.0
20-25 psi
25-30 psi
Applications
Base coats
Low and high solids,
clear coats, single
stages
7
EXL
HVLP Pressure Feed
Spray Gun
EXL
HVLP Suction Feed
Spray Gun
Precision
engineered patented
#2000 air cap - Meets
exacting performance
demands, producing an
extremely fine finish with
all materials. Developed in
conjunction with top
American and European
paint companies to
spray the latest materials.
Precision engineered patented
#2000 air cap - Meets exacting
performance demands, producing an
extremely fine finish with all materials. Developed in conjunction with
top American and European paint
companies to spray the latest
materials.
Large Spray Pattern for fast
coverage.
Large Spray Pattern for
fast coverage.
Even distribution of
materials for no mottling or striping - Excellent color
matching capabilities
Lightweight and comfortable - Classic DeVilbiss fit and
feel
feel
Economical servicing - Air cap, fluid tips and needles
are fully interchangeable and available separately.
Highly efficient HVLP design - Complies with
environmental regulation requiring high volume,
low pressure. Saves material. Very little overspray.
Stainless steel fluid tip, needle and fluid inlet adapter.
Includes: Air Cap Cleaning Kit, Spray Gun Lube
Even distribution of materials for
no mottling or striping - Excellent
color matching capabilities
Model No.
Inlet Air
Tip (mm)
Air
Cap
EXL-520P-11
1.1
2000
EXL-520P-14
1.4
2000
EXL-520P-18
1.8
2000
EXL-520P-22
2.2
2000
Applications
Model No.
Inlet Air
Tip (mm)
Air
Cap
Low to medium solids
Up to 12 oz./min.
High solids
Up to 12 oz./min.
High solids
Up to 16 oz./min.
High solids
Up to 18 oz./min.
EXL-520S-18
1.8
2000
EXL-520S-22
2.2
2000
Specifications
30 psi inlet pressure delivers 10 psi air cap pressure at 16 cfm air
volume
Applications
Base coat 20-25 psi
inlet pressure
Low and high solids
clear coats and single
stages 25-30 psi
inlet pressure
Specifications
volume
Anodized fluid passages
8
EXL
HVLP Gravity Feed
Spray Gun
Precision engineered
patented #2000 air cap - Meets
exacting performance demands,
producing an extremely fine finish
with all materials. Developed in
conjunction with top American
and European paint companies to
spray the latest materials.
Large Spray Pattern for fast
coverage.
Even distribution of materials for no mottling or striping Excellent color matching capabilities
feel
Less time spent on refills - True 1-Liter aluminum cup
with disposable push-on lid
Quick clean up and upside down spraying (no cup
leaks) - with E-Z LinerTM disposable cup liners
DeVilbiss SRiTM
HVLP Spray Gun
Fine Atomization and Spot Repair Versatility
Finally - a spot repair spray gun with the control needed for
spot repairs plus the comfort of a full-size spray gun. The
DeVilbiss SRITM is the ultimate spot repair spray
gun with the fit and feel of a full size spray
gun combined with the pattern range and
versatility needed for invisible, top quality
spot repairs.
Maximum Control Means Maximum
Performance
Small gun proportions
Ergonomically styled for operator
comfort
Full fan and spot patterns for spray
versatility
Full size air and fluid controls
Cheater value for precision air adjustments at
the spray gun.
Single finger trigger adjusts from fine feathering to
fadeouts
Uniform material distribution
Inlet Air
Tip (mm)
Inlet Air
Pressure
SRi-628-10
1.0
20-29 psi
Spot repairs
SRi-628-1.2
1.2
20-29 psi
Panel repairs,
Door jambs
Model No.
Applications
Includes:
1.0 mm fluid tip or 1.2 mm tip, 4 oz. disposable cup and lid. Wrench
(SRi-50), Spray lube (SSL-10)
Includes: Air Cap Cleaning Kit, Spray Gun Lube
Specifications:
29 psi air inlet pressure delivers 10 psi air cap pressure at 4.5 cfm
air volume required. (SRi-5033-205) Air Cap test Kit (order
separately) Provides consistent setup and regulatory proof of air
cap pressure.
Model No.
Inlet Air
Tip (mm)
Inlet Air
Pressure
EXL-620G-15
1.5
20-25 psi
25-30 psi
EXL-620G-18
1.8
20-25 psi
25-30 psi
Base coat
Low solids clear coats
single stages
High solids and
single stages
EXL-620G-22
2.2
20-25 psi
25-30 psi
High solids and
single stages
Applications
Specifications
volume
*Note: For finer control at lower fluid flows, order the optional .8
mm tip and needle separately.
Maximum Air Pressure:
Gun Body:
Nozzle and Needle:
Cup:
Cup Lid:
Air Inlet Size:
Gun Weight:
Gun Repair Kit:
100 psi (7 bar)
Anodized Aluminum
Stainless Steel
Nylon
Polypropylene
Universal 1/4” BSP & NPS (M)
13.7 oz.
SRi-426
9
FinishLine
Gravity Feed
FinishLine
Suction Feed
Economically-priced
Economically-priced
Available in conventional or compliant HVLP models
Available in conventional or compliant HVLP models
Durable, high quality construction: High grade
die-case alloy gun body. Stainless steel fluid inlet.
Alloyed resins for other components to keep gun
weight to a minimum. All materials resistant to solvents
and gun-washing fluids.
Durable, high quality construction: High grade
die-case alloy gun body. Stainless steel fluid inlet.
Alloyed resins for other components to keep gun
weight to a minimum. All materials resistant to solvents
and gun-washing fluids.
Precision engineered to produce well atomized,
uniform spray patterns
Precision engineered to produce well atomized,
uniform spray patterns
Easy-to-use controls: Precise spray pattern and fluid
flow adjustment. Patented spray pattern knob has
marker for repeatable settings from full fan to round
spray.
Easy-to-use controls: Precise spray pattern and fluid
flow adjustment. Patented spray pattern knob has
marker for repeatable settings from full fan to round
spray.
Waterborne compatible: Stainless steel fluid inlet and
fluid needle, plus alloy resin fluid tip.
Waterborne compatible: Stainless steel fluid inlet and
fluid needle, plus alloy resin fluid tip.
20-oz. lightweight acetal cup with screw-on lid:
Built-in “drip check” helps prevent leaks through lid
vent hole.
Quick clean-up and upside-down spraying with no cup
leaks with E-Z linerTM disposable cup liners.
TGC one-quart aluminum “drip-free” suction cup:
Two position valve allows operation as a “drip-free”
cup or as a conventional suction cup. “Drip-free
diaphragm” helps prevent leaks through lid vent hole.
Order No.
Model No.
Type
FLG-695-113 Conventional
FLG-695-113
Compliant
HVLP
Fluid
Tip (mm)
Air
Cap
1.3
#1
General purpose,
light to heavy
viscosity materials
FLG-694-115 Conventional
1.8/1.5*
#3
General purpose,
light to heavy
viscosity materials
FLG-693-322
Applications
* Compliant HVLP models come standard with two sizes of fluid tips
10
Order No.
Model No.
Type
Compliant
HVLP
Fluid
Tip (mm)
Air
Cap
1.6
#1
General purpose,
light to medium
viscosity materials
2.2/1.8*
#3
General purpose,
light to medium
viscosity materials
Applications
* Compliant HVLP models come standard with two sizes of fluid tips
VTZ HVLP Spray Gun
Reduced mottling with dye and toner stains
99% color repeatability of most NGR stains
Uniform coverage of top coats
50% less trigger pull
Working in conjunction with coating companies and
furniture manufacturers, DeVilbiss atomization engineers
have designed an innovative solution to reduce the incidence of mottling, a cloudy or blotchy finish appearance
typically seen when spraying various non-grain-raising dye,
toner stains, and semi wipes with standard HVLP guns. The
gun also achieves outstanding results when applying light
to medium topcoats with a viscosity between 18 and 28
seconds on a No. 2 Zahn.
The new DeVilbiss VTX spray gun uses a unique and
patented 3-stage atomization technology to overcome the
effects of mottling. Independent testing has confirmed the
VTX products:
Highly consistent, uniform spray patterns
Enhanced process control capability
Improved finish quality and appearance
Additional operator comfort with a 50% reduction in
dynamic trigger pull.
Model No.
VTX-18 (Use with flow rates at 15 oz/min. or less
VTX-30 (Use with flow rates from 15 to 30 oz/min.
Fluid Nozzle Assembly
The VTZ is designed to handle both thin and thick wood
finishing stains and is the first DeVilbiss product to use Jet
Impingement Atomization (JIA) technology. In this process,
the stain is:
1.hydraulically pre-atomized in an internal impingement
orifice, creating a vortex.
2.a hollow fluid bulb is then formed as a result of the
vortex; and
3.the stain is finely atomized with a 2000 air cap and baffle
combination.
These steps ensure highly consistent and uniform spray
patterns. The VTX design also provides maximum transfer
efficiency and complies with rules issued by SCAQMD and
other air quality authorities.
Maximum Air Pressure
For HVLP Compliance
delivers 10 psi air cap pressure
at 16 cfm
The VTZ spray gun set up has two fluid needle and nozzle
set-ups for these applications, and is equipped with an inline 100 mesh mini-strainer to ensure a clean supply of
material to the internal impingement chamber.
Model No.
VTX-18 (Use with flow rates at 15 oz/min. or less
VTX-30 (Use with flow rates from 15 to 30 oz/min.
100 PSI
30 PSI static, inlet pressure
Maximum Fluid Inlet Pressure
60 PSI
Gun Body
Wetted Parts
Drop Forged Aluminum
Stainless Steel, Delrin
Air Inlet Size
Fluid Inlet Size
1/4” NPS (M)
3/8” NPS (M)
Weight
Feed Type
21.6 oz (610 g)
Pressure
Service Bulletin
Gun Repair Kit
SB-2-282
KK-5085
11
EGHV Touch-Up Maximum Performer
HVLP Spray Gun
Body:
Weight:
Air Inlet:
Fluid Inlet:
Fluid Passages:
Feed Type:
Air Consumption:
Air Cap Pressure:
Service Bulletin:
Gun Repair Kit:
7.5 oz. (210 gr)
1/4” NPS (M)
1/4” NPS (M)
Stainless Steel
Suction feed
Pressure feed
4.3 CFM max. @
10 psi cap pressure
10 psi @ 80 psi inlet
SB-2-166
KK-5044
Comfortable and easy-to-use, the EGHV Touch-Up
Maximum Performer spray gun provides precise control for
the most exacting detail and touch-up work. The gun features
a long tapered fluid needle and a top-mounted trigger, and
weighs only 7.5 ounces, making it ideal for hours of
fatigue-free precision painting.
• Fluid delivery by attached suction feed or remote
pressure feed cup.
• Knurled knobs for fine adjustment of fluid flow and
spray pattern.
EGHV-532 gun and TGS-503 translucent polyethylene
cup provide a precision finish with less overspray.
Productivity and Finish Quality
The productivity and finish quality of any Maximum
Performer spray gun is determined by the air cap and fluid tip
combination.
EGHV Accessories
•
The EGHV Touch-UP Maximum Performer manual spray
gun is available with the following air cap and fluid tip setup,
factory assembled for immediate delivery.
•
Part No:
•
EGHV-531-397E*
*All wetted surfaces of EGHV are stainless steel
12
8 Oz Cup (TGS-503) Solvent-resistant
polyethylene cup is available.
Remote Cups
Two-quart remote cups are available in
aluminum (KB-555) or stainless steel
(KB-545-SS)
Hose assemblies, air cap test kit, gun
and hose cleaning equipment and other
Air Cap & Tip Selection Chart
JGHV, MSV and AGXV
*TYPICAL
SOLIDS BY
VOLUME
VISCOSITIES
TYPICAL
COATINGS
USED WITH
Low solids automotive
finishes, enamels,
lacquers, stains,
sealers, etc.
Low solids up to
25% solids by
volume
Up to 24 seconds,
#4 Ford cup
AIR CAP
MODEL NO.
PART NO.
TYPICAL PATTERN ** RECOMAIR
FLUID
SIZE
VOLUME
MENDED
(AT 10 psi
FLOW
FLUID
AIR CAP
RATES
TIPS
PRESSURE)
#33A
9" FX (.042")
JGHV-101-33A
18.75 CFM
Medium solids
enamels, urethanes,
solvent and waterborne furniture
topcoats, waterborne
automotive OEM
finishes, corrosion
protective coatings,
leather stains, acrylics,
epoxies, etc.
Medium-high solids
enamels, urethanes,
low VOC waterborne
furniture topcoats,
porcelain enamel,
corrosion protective
coatings, acrylics,
epoxies, etc.,
architectural and
industrial maintenance
coatings.
Low-medium solids,
up to 50% solids by
volume
Up to 28 seconds,
#4 Ford cup
#46 MP
11" FF (.055")
JGHV-101-46MP
22.5 CFM
Medium-high solids,
up to 72% solids by
volume
Over 28 seconds,
#4 Ford cup
* Viscosity Cup Reference
18 Seconds #4 Ford = 22 Seconds ZAHN #2
Up to
12 oz./min.
12-16 oz./min.
#83 MP
13" E (.070") or
D (.086")
JGHV-101-83MP
26.0 CFM
Over
16 oz./min.
** Recommended Fluid Tips Shown. Other Sizes Are Available.
13
Air Cap & Tip Selection Chart
EGHV AND TGHV
*TYPICAL
SOLIDS BY
VOLUME
VISCOSITIES
TYPICAL
COATINGS
USED WITH
Detail, touch-up
enamels, lacquers, etc.
Low solids up to
25% solids by
volume
Up to 24 seconds,
#4 Ford cup
AIR CAP
MODEL NO.
PART NO.
FLUID
SIZE
VOLUME
MENDED
(AT 10 psi
FLOW
FLUID
AIR CAP
RATES
TIPS
PRESSURE)
up to 6”
#397HV
EGHV-439-397HV
E (.070")
8.8 CFM
Detail, touch-up
enamels, lacquers, etc.
Low solids, up to
25% solids by
volume
Up to 24 seconds,
#4 Ford cup
Up to
6 oz./min.
up to 5”
#90HV
CV-39-90HV
F (.041")
6.7 CFM
4 oz./min.
JGA-HVLP
*TYPICAL
SOLIDS BY
VOLUME
VISCOSITIES
TYPICAL
COATINGS
USED WITH
Most common low
solids coatings, i.e.
enamels, lacquers,
stains, sealers, primers,
waterbornes, etc.
Low solids up to
30% solids by
volume
Up to 24 seconds,
#4 Ford cup
AIR CAP
MODEL NO.
PART NO.
FLUID
VOLUME
SIZE
MENDED
(AT 10 psi
FLOW
FLUID
AIR CAP
RATES
TIPS
PRESSURE)
11 1/2”
#98
JGHV-101-98
FX (.042")
11 CFM
Most common low
solids, coatings, i.e.,
automotive refinish
materials, enamels,
lacquers, stains,
sealers, primers,
waterborne, etc.
Low solids, up to
30% solids by
volume
Up to 24 seconds,
#4 Ford cup
* Viscosity Cup Reference
14
Up to
8 oz./min.
10” - 11”
#57
JGHV-101-57
22 CFM
Up to 12 oz./min.(gravity)
8 oz./min. (suction)
D (.086")
DE (.070”)
** Spray pattern size dependent upon type of feed,
material viscosity and air cap pressure.
Air Cap Test Kits
• KK-5033-33A Air Cap Test Kit –
Includes air cap and gauge, for use
with or #33A air caps only.
• KK-5033-46-MP Air Cap Test Kit –
with #46MP air caps only.
• KK-5033-83-MP Air Cap Test Kit –
with #83MP air caps only.
• KK-5033-90-HV Air Cap Test Kit –
Includes air cap, gauge and ring, for
use with #90HV air caps only.
*
• KK-5043 Air Cap Test Kit –Includes
air cap and gauge, for use with
#397HV air caps only.
• KK-5033-98 Air Cap Test Kit –
with JGA-HVLP spray gun using #98
air caps only.
*Air cap test kits may be required by some
air quality agencies. These kits are supplied
with a special air cap and test gauge to
demonstrate actual pressure being used at the
cap since it will vary depending on hose
length between the air regulator and gun.
This kit can be used as a quality control
device for consistent spraying each day. The
cap kit should not be used when finishes are
being applied.
Fluid Tips and Needles
NUMBER ON FLUID TIP
ORDER TIP
AND NEEDLE SET
AV-2115-FF, FX
AV-2120-D, E, FF, FX
AV-4915-D, E, FF, FX, G
JGA-4040-FF, FX (1)
JGA-4045-D, E, FF, FX (1)
JGA-4056-D, E, FF, FX, G (2)
JGA-4051-D, E, FF, FX (2)
AV-2115-FF, FX
AV-2120-D, E
AV-2120-FF, FX
AV-4915-E, FF, FX
AGX-4402-FF, FX (1)
AGX-4483-D,E (1)
AGX-4600-FF, FX (1)
AGX-4300-E, FF, FX (2)
AGX-4613-D, E, FF, FX (2)
EGA-60-E, F
EGA-4000-E, F (1)
CV-30-F-HV
TGHV-4000-F(5)
TGHV-4001-F(3)
For JGHV and MSV
For AGXV
Maximum
Performer
For EGHV
For TGHV
NUMBER ON FLUID TIP
ORDER TIP
AND NEEDLE SET
AV-2115-FX
AV-4915
JGA-4040-FX (1)
JGA-4056-FX (2)
AV-2115-DFF
AV-2125-DFW
AV-2120-DE
JGA-4046-14 (6)
JGA-4046-16 (6)
AGX-4046-18 (6)
AV-2125-DE
AV-2125-D
JGA-4046-18 (6)
JGA-4046-12(6)
For JGA-HVLP
For GFG-HVLP
Classic
Series
JGA-HVLP (SUCTION)
(1)
(2)
(3)
(4)
(5)
(6)
400-grade stainless steel, fluid tip, 303 grade S.S. Needle (matched set)
300-grade stainless steel with U.H.M.W. polyethylene seat in fluid tip (matched set).
Acetal and 300-grade stainless steel tip
Composite sprayhead, 400-grade stainless steel needle with U.H.M.W. polyethylene tip.
300-grade stainless steel (matched set)
400-grade stainless steel fluid tip, 303 grade S.S. Needle (matched set)
15
MBC-510 Manual Spray Gun
With Removable-Head
Combining a drop forged aluminum
body with a forged removable spray
head, the MBC-510 spray gun is ideal
for applications that require maximum
output and quick changeovers.
• Removable spray head allows for
reduced downtime on nozzle
combination changeovers.
• MBC spray guns have nickel-plated
brass fluid passages and stainless
steel fluid tip and needle.
• Ideal for zinc coatings
• Applications include oil platforms,
corrosion control and bridge
maintenance delivery.
The following air cap and fluid tip setups are factory assembled for immediate
delivery.
Part No.
MBC-510-30EX
MBC-510-64HDD
MBC-510-64HDE MBC-510-704E
information on the specific gun model,
air cap and fluid tip you will receive.
Example: MBC-510Fluid Tip Size
Air Cap Number
Basic Gun Model
Chart 1 Fluid Tip (Nozzle), Air
Cap and Needle Combinations
These guns with fluid tip and needle
can be ordered separately without air
cap and retaining ring:
MBC-510-D
MBC-510-E
MBC-510-EX
Part No.
MBC-510-FF
MBC-510-FX
Body:
Weight:
27 oz. (756 gr) with air
cap and ring
Air Inlet: 100 psi max, 1/4" NPS (M)
Fluid Inlet: 100 psi max, 3/8" NPS(M)
Fluid Passages:
Nickel-plated brass
Wetted Parts:
Nickel-plated brass
Feed Type:
Pressure feed
Suction feed
Service Bulletin:
SB-2-301
Gun Repair Kit:
KK-4058-1
Accessories
• Hose assemblies, air control, pressure
tanks, cups, gun and hose cleaning
equipment and other accessories are
available.
16
JGA-Plus Standard Size
Manual Spray Gun
• The JGA standard -size manual spray
gun sets industry standards for highproduction performance.
• An economical option for waterborne
and solvent-based material applications, the JGA stainless steel air
spray gun delivers the quality results
you need for tough applications.
• Offers the comfortable fit and feel
operators prefer.
The JGA-Plus standard-size spray gun
is available with the following air cap
and fluid tip set-ups, factory-assembled
for immediate delivery. However, these
are only the most popular set-ups – for
other air cap and tip combinations that
can be ordered separately.
These guns with fluid tip
and needle can be ordered
separately without air cap
and retaining ring:
Part No.
JGA-510-D*
JGA-510-FX*
JGA-510-E*
JGA-510-3-FF**
JGA-510-EX* JGA-510-3-FX**
JGA-510-FF*
Example: JGA-510Fluid Tip Size
Air Cap Number
Basic Gun Model
Accessories
• Hose assemblies, air control,
pressure tanks, cups, gun and hose
cleaning equipment and other
accessories are also available.
• For optional tip and needle sets.
Part No.
JGA-510-30EX
JGA-510-765FF
JGA-510-65HDD JGA-510-765FX
JGA-510-704E
JGA-510-797E
JGA-510-704FF JGA-510-797FF
JGA-510-704FX JGA-510-80EX
JGA-510-765E
JGA-510-797FX
Body:
Weight:
21.6 oz. (613 gr) with air
cap and ring
Air Inlet: 100 psi max, 1/4" NPS (M)
Fluid Inlet: 100 psi max, 3/8" NPS (M)
Fluid Passages: 300-grade stainless steel
Feed Type:
Pressure feed,
Suction feed (EX)
Service Bulletin:
SB-2-252
Gun Repair Kit:
KK-4987-2
17
JGA-Plus Standard Size
Manual Spray Gun (cont’)
JGA-HVLP and MSA-HVLP Application Guide
The economical way to convert
DeVilbiss conventional air spray guns
to Classic Series HVLP performance
by using a conversion kit. Simple to
convert for on-site retrofit.
• Maximum 8 oz./min. fluid flow.
• Lower solids coatings.
• Medium to high V.O.C. coatings
(4.0-5.0 lbs./gal.).
• Smaller compressors - 3 h.p. is
usually sufficient.
• Limited air supply - requires only
11 CFM at 10 PSI air cap
pressure.
• Class “B” finish quality
requirements.
JGA/MSA-TEK offers a simple
conversion to HVLP pressure feed by
changing the air cap, baffle and baffle
gasket.
18
MSA Mid-Size Manual Spray Gun
Designed to help reduce operator
fatigue while offering excellent
comfort and control, the MSA midsize
spray gun is lighter and more compact
than our standard-size JGA gun. That
means you get the same quality and
high-efficiency performance provided
by our JGA-Plus spray gun, in a
smaller model that weighs only 17
ounces.
• Air caps and replacement parts are
interchangeable with JGA spray
guns (the air inlet fitting is the only
exception).
Quality
of any DeVilbiss conventional air
spray gun are determined by the air
cap and fluid tip combination.
The MSA midsize spray gun is
available with the following air cap and
fluid tip set-ups, factory-assembled for
immediate delivery. However, these are
only the most popular set-ups – for other
air cap and tip combinations that can be
ordered separately.
Part No.
MSA-510-35LE
MSA-510-704LFF
MSA-510-35LFF MSA-510-704LFX
MSA-510-35LFX MSA-510-797LE
MSA-510-704LE MSA-510-797LFF
These guns with fluid tip and needle
can be ordered separately without air
cap and retaining ring:
MSA-510-E*
MSA-510-EX*
MSA-510-FF*
MSA-510-FX*
Part No.
MSA-510-3-E**
MSA-510-3-FF**
MSA-510-3-FX**
* Models include 400-grade
stainless steel tips and needles.
** Models include “premium”
300-grade stainless steel tip with
U.H.M.W. polyethylene insert
(needle seat) and 300-grade
stainless steel needle.
information on the specific gun
model, air cap and fluid tip you
will receive.
Example: MSA-510Fluid Tip Size
Air Cap Number
Basic Gun Model
Body:
Weight:
17 oz. (476 gr)
Air Inlet:
100 psi max, 1/4" NPS (M)
Fluid Inlet:
Fluid Passages:
Feed Type:
Pressure feed
Suction feed
Service Bulletin:
SB-2-257
Gun Repair Kit:
KK-4987-2
Accessories
• For optional tip and needle sets.
Decorator Spray Gun
MSA-510-DEC
The MSA-510-DEC decorator spray
gun features a spatter cap to create
decorative textured finishes.
Body:
Drop forged aluminum Weight:
18.4 oz. (515 gr)
Air Inlet:
Fluid Inlet:
Fluid Passages:
Wetted Parts:
300 and 400-grade
stainless steel, hardened alloy
Feed Type:
Pressure feed
Service Bulletin:
SB-2-319
Gun Repair Kit:
KK-4987-2
Can be converted to HVLP.
19
EGA Touch-Up Manual Spray Gun
The gun of choice for touch-up,
shading, edging and detail decorating,
the EGA touch-up gun provides
precise control for any type of delicate
spray finishing applications. Designed
for external mixing applications, the
gun features a forefinger trigger to
enhance operator control, and a long
needle taper to make detail work easy.
• Equipped with stainless steel tip
and needle.
• Knurled knobs allow fine spray
adjustments for fluid and pattern
control.
Quality
of any DeVilbiss conventional air
spray gun is determined by the air cap
and fluid tip combination.
The EGA touch-up gun is available with
the following air cap and fluid tip set-ups,
factory-assembled for immediate delivery.
Part No.
EGA-503-390F
When ordering DeVilbiss spray guns, the
part number includes information on the
specific gun model, air cap and fluid tip you
will receive.
Example: EGA-503Fluid Tip Size
Air Cap Number
Basic Gun Model
Body:
Weight:
7 oz. (196 gr) with air cap
and ring
Air Inlet:
1/4" NPS (M)
Fluid Inlet:
1/4" NPS (M)
Wetted Parts:
Aluminum 400-grade
stainless steel
Feed Type:
Pressure feed
Suction feed
Service Bulletin:
SB-2-163
Gun Repair Kit:
KK-5044
Accessories
Note: EGA-503 model replaces
EGA-502.
20
Other Equipment and Accessories
Cleaning Brushes
For cleaning the threads and recesses of
the gun body.
3/8" dia. brush: 42884-214-K5 (pkg. of 5)
5/8" dia. brush: 42884-215-K10 (pkg. of 10)
Spray Gun Lube
SSL-10-K12
Specially formulated spray gun lube
improves performance and extends the
life of spray equipment. Contains no
silicones or petroleum distillates to
contaminate paint and coatings. Case
of 12 (2-oz.) bottles. Not for use with
air tools and high RPM equipment.
Spray Gun Wrench
WR-103
Versatile tool fits fluid and air hose
connections, as well as adapters and
packing nuts.
JGA Gun Fluid Tube
JGA-444
Handy tube combines the fluid and
air hoses at the gun handle to prevent
twisted lines and keep hoses from
dragging over work. 3/8” NPS thread.
Use this stud to attach automatic spray
guns to 3/4” rods and increase the
flexibility and versatility of your spray
system. 16” long, 48 oz. (1344 gr)
shipping weight
Save money by reducing cleaning
time and maintenance with these
covers that also limit operator
exposure to overspray.
GC-100-K4 (pkg. of 4)
GC-100-K48 (pkg. of 48)
Thread Adapter
Thread adapters provide the correct hook-up for spray guns, hoses,
tanks and other spray equipment. They work with most standard thread
applications.
PART NO.
MALE
MALE
FEMALE
AD-404
P-H-4105
H-1766
H-2008
AD-31
AD-26
H-1580
H-1446
AD-11
–
–
1/8" NPT
1/4" NPT
1/4" NPS
1/4" NPS
1/4" NPT
3/8" NPS
3/8" NPS
1/4" NPS
3/8" NPS
1/4" NPS
1/4" NPS
1/4" NPS
3/8" NPS
3/8" NPS
3/8" NPS
3/8" NPT
3/8" NPS
1/4" NPS
–
–
–
–
–
–
–
Manual Spray Gun Extensions
For hard to reach locations. Attach to
most conventional and HVLP spray
guns. For conventional coatings.
Compatible with brass wetted parts.
Comes with 1/4” NPS (f) x 1/4” NPS (m)
air inlet adapter.
Length
in feet
Mounting Stud - AGA-414
Disposable Spray Gun Covers
Part
No.
Shipping
Weight (lbs.)
Actual
Weight (lbs.)
4
54-296
4
3
6
54-297
5.25
4
8
54-298
6.5
5
Universal Clamp - AGA-415
This clamp attaches directly to the gun
stud and clamps onto 3/4” rod, allowing
the gun to rotate to an angle. 13.5 oz.
(378 gr) shipping weight.
21
Spray Equipment
JGHV-531-46FF (.055)
DeVilbiss MAXIMUM PERFORMER HVLP spray gun, medium solids,
enamels, top coats, Aerospace, automotive OEM finishes, corrosion
protective coatings, acrylics, epoxies up to 50% solids (12-16 oz.min./
28 seconds #4 Ford). Stainless Steel fluid passages and stainless steel
tip and needle with 46MP air cap, maximum 11” pattern.
JGHV Spray Gun
Maximum Performer HVLP spray guns also meet operational
requirements of California South Coast Air Quality Management
District and other air quality authorities. DeVilbiss HVLP spray guns
are protected by Patents 5,344,078, 5,209,405 & 5,090,623.
KK-4987-2 Repair Kit. Used on JGHV, MSV, MSA and JGA
spray guns
KB-555 - 2 quart aluminum remote pressure cup
KB Cup
KB-545-SS - 2 quart Stainless Steel remote pressure cup
TLC-576 - 1 quart aluminum pressure cup (for attached use)
TSC-591 - 1 quart Stainless Steel cup (for attached use)
(must use KK-4980 regulator, purchase separately)
QMGT-5223 - 2 gallon ASME galvanized pressure tank, double
regulation, agitator and air motor
QMST-5223 - 2 gallon ASME stainless steel pressure tank, double
TLC Cup &
Regulator
regulation, agitator and air motor
KB-4006 - 6 ft. hose sets (air and fluid) with fittings for use with
remote KB cups
71-1355 - 3/8” x 25’ I.D. air hose assembly with fittings
71-3303 - 3/8” x 25’ I.D. fluid hose assembly with fittings
71-31101 - 3/8 x 25 I.D. Ergoflex air hose
QMGT/QMST
Pressure Tank
22
Spray Equipment Packages
(fully assembled)
FLHVLP-1 Outfit Consists of:
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1) JGHV-531-46FF HVLP spray gun of choice
(1) KB-545-SS 2 quart Stainless Steel remote pressure
cup
(1) KB-4006 6 ft. hose set with fittings
(1) JGHV-531-46FF spray gun of choice
(1) KB-555 2 quart aluminum remote pressure cup
**FLHVLP-3 Outfit Consists of:
(1) KB-555 2 quart aluminum remote pressure cup
(1)
(1)
(1)
(1)
(1)
(1)
(1)
QMGT 2 gallon galvanized ASME pressure tank
Double regulation
Air Motor and agitator
Disposable liner
JGHV-531-46 FF HVLP spray gun of choice
71-3303 - 75 ft 3/8 fluid hose
71-1105 - 75’ 1/4 air hose
QMST 2 gallon stainless steel ASME pressure tank
Double regulation
Air Motor and agitator
Disposable liner
JGHV-531-46 FF HVLP spray gun of choice
71-3303 - 75 ft 3/8 fluid hose
71-1105 - 75’ 1/4 air hose
*FLHVLP-7 Outfit Consists of:
(1) JGHV-531-46FF HVLP spray gun
(1) TLC-576 attached 1 quart pressure cup
(1) KK-4980 pressure regulator
(1) JGHV-531-46FF HVLP spray gun
(1) TSC-591 Stainless Steel attached pressure cup
(1) KK-4980 pressure regulator
FLHVLP-4 Outfit
Consists of:
(1) KB-545-SS 2 quart Stainless Steel remote pressure
cup
**
4940-01-363-6937-FLHVLP-613 Outfit same as
FLHVLP-3 different cup
* 4940-01-363-6938 - FLHVLP-605 Outfit same as
FLHVLP-7
Note: Model JGHV-531-46FF tested/verified ETV/EPA.
See WWW.EPA.GOV/ETV
All outfits may be modified to suit your needs.
Other model HVLP spray guns and
ASME pressure tanks available.
23
Solvent SaversTM Hose / Gun Cleaners
Simple, easy-to-use cleaners speed up
equipment cleaning and save solvent
(up to 86% savings!), which reduces
V.O.C. emissions. Operate with
compressed air. Provide finely atomized
blast of solvent traveling through fluid
passages of spray guns, hoses, etc.
Metering permits varying air/solvent
mix. Equipped with safety valve. 1/4"
NPS (M) air and 3/8" NPS (M) fluid
connections.
Solvent Savers™ Hose/Gun Cleaners
SHIP WT. MAX. WORKING
PART NO. COMPUTER NO.
*HD-503
180037
*QMGZ-5200
CAPACITY
(LBS.)
PRESSURE
2 qt.
5
50 psi
2 gal
42
110 psi
MATERIAL CONSTRUCTION
(IN CONTACT W/FLUID)
Aluminum, nickel plated brass,
Teflon and Thiokol gasket
Galvanized steel, aluminum,
nickel plated brass, Teflon &
Thiokol gaskets, polyethylene
tank liner
*Note: Not suitable for use with chlorinated solvents, such as 1,1,1 trichloroethylene or methylene
chloride.
Fluid Strainers and Equipment
Gun Mounted
Strainer
VS-531
Gun Mounted
Strainer
VS-532
This strainer is available in 100
mesh and can be attached to
the gun inlet.
Designed for use with JGA
spray guns, this strainer
mounts on the fluid inlet and
allows the filter screen to be
cleaned or replaced without
removing the strainer housing.
PLH-MF-6-100
Fluid Strainer
PLH-MFC-100
100 Mesh Screen
Lightweight stainless
steel final filter, 250 PSI
maximum working
pressure
In-Line
Strainer
VS-534
Stainless steel swivel
strainer mounts to the
rank or pump and has
a 100 mesh replaceable,
cylindrical filter.
Gravity Gun
Strainer
KGP-5-K5
Gravity Fluid Strainer
Gun Cup Strainer
50-mesh, 149-278
A final strainer for atomized
spray gun cups. The 50mesh brass filter screen for all
enamels and lacquers. The
strainer is pressed on and
removed from the end of
the siphon tube. Its gasket
prevents by-pass and holds
firmly on siphon tube sizes
up to 7/16” diameter. Box
of 10.
Fluid Strainers
STRAINER
PART NO.
STRAINER TYPE
MAX. WORKING
PRESSURE
INLET
THREADS
OUTLET
THREADS
WETTED
PARTS
300
300
3/8"NPS(M)
3/8"NPS(M)
3/8"NPS(F)
3/8"NPS(F)
Swivel
CS
PB
250
3/8” NPS (M)
3/8” NPS (F)
VS-534
300
3/8"NPS(F)
Swivel
3/8"NPS(M)
PB = Plated Brass
CS = Carbon Steel
SCREEN
PART NO.
MESH
SIZE
MICRON
SIZE
31144-310-K10
VS-58-K10
100
100
149
149
SS
PLH-MFC-100
100
149
SS
VS-58-K10
100
149
Gun Mounted Strainers
VS-531
VS-532
Gun Mounted Mini Strainers
PLH-MF-6-100
In-Line Strainer
SS = Stainless Steel
24
Selecting the Air Cap, Fluid Tip and Needle
The air cap directs compressed air into the
material stream to atomize the fluid and
form the spray pattern. The fluid tip and
needle meter direct the flow of material
from the gun into the air stream.
Because they all affect the quality of the
spray pattern, the air cap, fluid tip and
needle are usually selected as a unit.
Together, these three items are referred to
as the nozzle combination.
Types of Air Caps
Air caps are defined by their methods of
delivering and mixing the spray finishing
materials. Delivery methods include
pressure feed, suction feed and gravity
feed. Chart 1 depicts flow rate range, fluid tip
size and recommended air caps for a typical
product finish.
Types of Fluid Tips
Fluid tips are made from a variety of
metals. The application determines the
type of fluid tip to use. Stainless steel tips
are ideal for corrosive materials. The
standard tip on most DeVilbiss guns is
400-grade stainless steel; 300-grade
“premium” fluid tips with U.H.M.W.
polyethylene insert (needle seat) are also
available. We also offer carbolloy fluid tip
for extremely abrasive materials.
The amount of material discharged from a
pressure feed gun depends on a number
of factors: the material viscosity, the fluid
tip inside diameter, the length and size of
hose, and the pressure on the material.
Generally, the larger the opening, the more
material discharged.
However, if the fluid tip is too large, the
operator will lose control over the material
discharge. And if the fluid tip opening is
too small, the discharge velocity will be too
high. This means the air coming from the
cap will not atomize the material properly,
and the pattern will be distorted.
With a suction feed gun, the fluid flow in
ounces per minute is relatively stable
because it is determined by atmospheric
pressure. It is also determined by the
material viscosity and air cap pressure.
25
Air Cap Selection Guide
Conventional Air Spray Guns
26
Fluid Tip and Needle Selection Guide
27
Tanks and Cups
DeVilbiss Tank/Binks Tank
Crossover Chart (cont’)
All Tanks are Featured in Binks Section, Starting on Page 47
PART NO.
2 Gallon
QMGT-5200
QMGT-5201
QMGT-5210
QMGT-5211
QMGT-5213
QMGT-5220
QMGT-5221
QMGT-5223
QMGT-5226
QMGT-5231
Replacement
83G-210
83G-211
83G-210
83G-211
83G-213
83G-220
83G-221
83G-221
83S-526
83G-221
Description for Binks Replacement in Galvanized Steel
The SIMILAR replacement has a single regulator, and is branded Binks
The DIRECT replacement has a single regulator, and is branded Binks
The DIRECT replacement is branded Binks. There are no other differences
The SIMILAR replacement has a direct drive agitator
The SIMILAR replacement is Stainless Steel and is branded Binks
The regulators on the SIMILAR replacement have a lesser turndown ration.
These are also branded Binks
5 Gallon
QMGT-5500
QMGT-5502
83G-510
83G-513
QMGT-5510
QMGT-5512
83G-510
83G-513
QMGT-5513
QMGT-5520
QMGT-5522
83G-513
83G-520
83G-523
QMGT-5523
QMGT-5530
83G-523
83G-52
The SIMILAR replacement has a single regulator, and is branded Binks
The SIMILAR replacement has a single regulator and an air driven/gear reduced
agitator and is branded Binks
The DIRECT replacement is branded Binsk. There are no other differences
The SIMILAR replacement has an air driven/gear reduced agitator and is
branded Binks
The SIMILAR replacement has an air driven/gear reduced agitator and is
branded Binks
The regulators on teh SIMILAR replacement have a lesser turndown ratio.
These are also branded Binks
10 Gallon
QMGT-51000
QMGT-51010
QMGT-51013
QMGT-51020
QMGT-51023
83G-1010
83G-1010
83G-1013
83G-1020
83G-1023
The
The
The
The
The
SIMILAR replacement has a single regulator, and is branded Binks
DIRECT replacement is branded Binks. There are no other differences
15 Gallon
QMGT-51500
QMGT-51510
QMGT-51513
QMGT-51520
QMGT-51523
83G-1500
83G-1510
83G-1513
83G-1520
83G-1523
The
The
The
The
The
DIRECT
DIRECT
DIRECT
DIRECT
DIRECT
replacement
replacement
replacement
replacement
replacement
is
is
is
is
is
branded
branded
branded
branded
branded
Binks.
Binks.
Binks.
Binks.
Binks.
There
There
There
There
There
are
are
are
are
are
no
no
no
no
no
other
other
other
other
other
differences
differences
differences
differences
differences
CALL
MAIL
Toll-Free
your order
800-365-7565
12834 Gravois
to order
St. Louis, MO 63127
28
FAX
your order
314-729-7099
E-MAIL
your order
info@fluidair.com
WEBSITE
Visit our site
www.fluidair.com
and link to
www.gsa.gov
Tanks and Cups
Pressure and Suction Feed Cups
Teflon®-Lined Suction Cup
TLC-555
Aluminum, one-quart cup featuring
Teflon® lining for fast, easy cleaning
and reduced color contamination.
Drip-free lid design has two-position
valve which allows for operation as
“drip-free” cup or as conventional
suction cup. Use with all suction feed
spray guns.
Low Pressure Cup for HVLP
TLC-576
Aluminum, one-quart, low
pressure cup for HVLP applications.
Teflon®-lined for fast, easy cleaning.
Solvent-resistant check valve.
Requires KK-4980 for cup air
regulation. (Order separately)
Polyethylene Suction Cup
TGS-503
8-oz. cup size. Combines engineered
resin lid with translucent polyethylene
cup – liquid level visible. Molded-in
graduations for mixing ratios.
Lightweight and easy to clean.
Nonstaining. Includes cup closure.
Compatible with all solvents. Use with
EGA-502, EGHV-530 or any suction
feed gun with 1/4" NPS threads.
Stainless Steel Cups
Aluminum Suction Cups
Aluminum suction cups incorporate a
two-position special lid design – one
as drip-free cup or the other as
conventional suction feed cup. Smooth
metal surfaces make cleanup and
changing paint fast and easy. Use with
all suction feed spray guns.
TGC-545 - Quart Capacity Suction Cup
TGC-536 - Pint Capacity Suction Cup
One-quart cups made from 300
series stainless steel, designed for use
Gravity Feed Cups
with waterbased materials and exempt
Made of strong, lightweight material
solvents. The .030" wall thickness
for
durability. Features a “dry check”
makes it more durable than
competitive cups, yet still lightweight. device integral with cup lid to avoid
And the fluid tube is stainless steel for spillage from vent hole.
KGP-509-1 - 8-oz. Cup (Nylon)
added durability and corrosion
resistance.
GFC-501 - 20-oz. Cup (Delrin)
TSC-591 - HVLP Low Pressure
Feed Cup. Requires KK-4980 for cup
air regulation (order separately)
TSC-595 - Suction Feed Cup
29
Tanks and Cups
KB Series Pressure Feed Cups
For use with both conventional air
spray systems and HVLP systems, the
KB II series, two-quart cups feature a
“pistol grip” carrying handle, and right
or left-handed design for comfort and
ease of handling. An easy-open lid and
wide cup mouth allow for fast filling
and cleanup. KB Series cups also
feature a solvent resistant check valve
and a wide base for greater stability.
KB series cups are ideal for handling
heavier viscosity materials, higher flow
rates, as well as low fluid flow rates of
10 ounces per minute or less. Fluid
pressure range of 2-30 psi. Order air/
fluid hose assemblies separately.
KB-4004 - 4-foot hose length.
KB-4006 - 6-foot hose length most
coating materials and solvents.
Stainless Steel Cup
KB-545-SS
DeVilbiss KB Stainless Steel
model cups are designed for use
with waterbornes, halogenated
hydrocarbons and other corrosive
materials.
Aluminum Cup
KB-555
KK-5051 Disposable Cup
Liner Kit includes
20 liners, 20 lids and 3 rings
DeVilbiss KB Aluminum model
cups are compatible with most coating
materials and solvents.
Pressure and Suction Feed Cups
COMPLETE CUP
ASSEMBLY
PART NO.
CONNECTION
THREAD SIZE
FLUID
AIR
CAPACITY
MATERIAL
2 qt.
2 qt.
1 qt.
1 qt.
Aluminum
Stainless Steel
Stainless Steel
Aluminum w/Teflon® Lining
CUP AND COVER
ASSEMBLY
CUP ONLY
PART NO.
APPROX. SHIP
WT/ COMPLETE
CUP AND LID
—
—
—
KB-422
KB-442
TSC-400
TLC-401
3 lbs. 14 oz.
5 lbs. 2 oz.
20 oz.
18 oz.
TGC-432
KR-428-2
Pressure Feed
KB-555
KB-545-SS
TSC-591
TLC-576
3/8"NPS(M) 1/4" NPS(M)
3/8"NPS(M) 1/4" NPS(M)
3/8"NPS(M)
—
3/8"NPS(F)
—
Suction Feed
TGC-536
TGC-545
TGS-503
TLC-555
TSC-595
Gravity Feed
KGP-509-1
KGP-510-1
6 oz.
Aluminum
3/8"NPS(F)
1 qt.
Aluminum
3/8"NPS(F)
8 oz.
Polyethylene
1/4"NPS(F)
1 qt. Aluminum w/Teflon® Lining3/8"NPS(F)
1 qt.
Stainless Steel
3/8"NPS(M)
—
—
—
—
—
—
—
TGS-406
—
TLC-401
TSC-400
12 oz.
18 oz.
3 oz
18 oz.
20 oz.
8 oz.
20 oz.
—
—
—
—
—
––
3 oz.
6 oz.
Nylon
Delrin
3/8"BSP(M)
3/8"BSP(M)
* Use with GFG and GFHV guns only.
** Order KK-4980 Air Regulator Kit in addition to cup.
30
CleanAir Centrifugal Filter-Regulator Units
Excellent for eliminating moisture
and dirt from an air supply, DeVilbiss
CleanAir centrifugal units supply
cleaner, drier air to each spray gun in a
system. This cleaner air can also
increase the life of pneumatic tools.
• Filters out water and oil aerosols and
dirt particulates to 5 microns.
• Ideal for most spray applications, air
tools and equipment.
• Water droplets collected in the bowl
are removed by an automatic drain
(standard feature). No need to
manually drain.
HFRL-511
Service Bulletin SB-6-148-E
Quick-release filter bowl and spin-off
5-micron filter element allow one-minute
filter changes without tools. Pressure drops
are minimized by large air inlet and outlet
and large internal air passages.
HAF-502
HAF-503
P/N#
HAF-502
HAF-503
HFRL-508
HFRL-509
HFRL-508
HFRL-509
Service Bulletin
SB6-146-B
SB-6-148-E
SB-6-148-E
SB-6-148-E
31
CleanAir Centrifugal Filter-Regulator Units
Centrifugal Air Filter Units
PART NO.
Air
inlet
Tornado
swirl ring
Reversible
5-micron
filter
Baffle
Quiet
zone
Automatic
drain
Flexible
tubing
Tornado-like swirling action removes moisture
which collects in the baffled “quiet zone.”
The reusable 5-micron filter catches smaller
impurities. Accumulated liquid is carried
away by the automatic drain.
Accessories
Filtering Capacity (micron)
Flow Rate (CFM)
Max. Inlet Pressure (psi)
Max. Operating Temp.
Inlet Port Size
Outlet Port Size
Bowl Capacity
Shipping Weight
Service Bulletin
HAF-502
HAF-503
5
100 @ 90 psi
150
150oF
1/2" NPT (F)
1/2" NPT (F)
17 oz.
1 lb. 7 oz.
SB-6-146
5
150 @ 90 psi
150
150oF
3/4" NPT (F)
3/4" NPT (F)
34 oz.
3 lbs. 1 oz.
SB-6-148
Centrifugal Filter-Regulator Units
PART NO.
HFRL-508
Filtering Capacity (micron)
Flow Rate (CFM)
Regulated Pressure Range (psi)
Inlet Port Size
Regulated Outlets (w/ball valve)
Non-Regulated Outlets (w/ball valve)
Bowl Capacity
Air Filter Included
Quality Air Regulators/Model
Air Gauges (0 - 100 psi)
Shipping Weight
Service Bulletin
5
50+
150
0 - 125
150oF
1/2" NPT (F)
(1) 1/4" NPS (M)
(1) 1/4" NPS (M)
17 oz.
HAF-502
(1) HAR-506
1
1
9 lbs.
SB-6-146
HFRL-509
HFRL-511
5
5
80+
120+
150
150
0 - 125
0 - 125
150oF
150oF
3/4" NPT (F)
3/4" NPT (F)
(2) 1/4" NPS (M) (4) 1/4" NPS (M)
(1) 1/4" NPS (M) (1) 1/4" NPS (M)
34 oz.
34 oz.
HAF-503
HAF-503
(1) HAR-507
(2) HAR-507
1
2
1
1
15 lbs.
18 lbs.
SB-6-148
SB-6-148
• Filter Element Kits (5-Micron
• Mounting Bracket Assembly Kits
reusable)
For HAF-502 air filter and HFRL-508
For HAF-502 air filter and HFRL-508
regulator; order HAF-407.
For HAF-503 air filter, and HFRL-509 regulator; order HAF-6.
For HAF-503 air filter, and HFRL-509
and HFRL-511 regulators, order
HAF-408.
and HFRL-511 regulators, order HAF-15.
CALL
MAIL
Toll-Free
your order
800-365-7565 12834 Gravois Rd.
to order
St. Louis, MO 63127
32
FAX
your order
314-729-7099
E-MAIL
your order
info@fluidair.com
WEBSITE
Visit our site
www.fluidair.com
and link to
www.gsa.gov
CleanAir Coalescer Filter-Regulator Units
CleanAir coalescer filters remove
water, dirt and oil from the system
down to .01 micron. DeVilbiss
coalescer filter units are designed
with a quick-release bowl and
spin-off element for filter changes
without tools. In addition, a filterchange indicator alerts the operator
when the element requires changing.
• Borosilicate glass microfiber filter is
engineered for high flow, high
efficiency, quick change and low
pressure drop.
• Ideal for most spray applications,
especially where oil aerosols may
be a problem.
• Automatic bowl drain and 6' hose
eliminate oil and water buildup
manually drain.
The HAF-508 is the coalescer filter
only. In combination with the
centrifugal filter, there are three
choices – the HAF-509 non-regulated
unit and the two regulated models –
HFRL-512 and HFRL-513.
HFRL-513
Service Bulletin SB-6-148-E
HAF-509
Service Bulletin
SB-6-148-B
HFRL-512
Service Bulletin
SB-6-148-E
33
CleanAir Coalescer Filter-Regulator Units
Centrifugal-Coalescer Filter Units
A
NON-REGULATED MODELS
G
B
C
D
E
F
Centrifugal Filtering Capacity (micron)
Coalescer Filtering Capacity (micron)
Flow Rate (CFM)
Inlet Port Size
Outlet Port Size
Bowl Capacity
Shipping Weight
Service Bulletin
Accessories
• Mounting bracket assembly kit is
available; order HAF-408.
• Centrifugal filter element kit has
reusable 5-micron filter; order
HAF-15.
• Coalescer filter element kit has
.01-micron filter; order HAF-38.
34
HAF-509
CENTRIFUGAL
& COALESCER
5
.01
150 @ 90 psi
150
150oF
3/4" NPT (F)
3/4" NPT (F)
34 oz.
3 lbs. 2 oz.
SB-6-148
5
.01
150 @ 90 psi
150
150oF
3/4" NPT (F)
3/4" NPT (F)
34 oz.
6 lbs. 3 oz.
SB-6-148
Coalescer-Filter Regulator Units
REGULATED MODELS
Pre-filter support fabric prevents media
migration, increasing element life. Stainless
steel screens provide fail-safe protection against
accidental shock loads and high pressure drops
in either direction. Anti re-entrainment barrier
prevents liquid carryover, even in shock
conditions, and is compatible with mineral and
synthetic lubricants.
A – Easy-fit captive O-ring
B – Corrosion-resistant end caps
C – Pre-filter support fabric
D – Stainless steel support screens
E – Anti re-entrainment barrier
F – Borosilicate glass microfiber filter
G – High-strength epoxy sealant
HAF-508
COALESCER*
Centrifugal Filtering Capacity (micron)
Coalescer Filtering Capacity (micron)
Flow Rate (CFM)
Regulated Pressure Range (psi)
Inlet Port Size
Regulated Outlets (w/ ball valve)
Non-Regulated Outlets (w/ ball valve)
Bowl Capacity
Quality Air Regulators/Model
Shipping Weight
Service Bulletin
HFRL-512
HFRL-513
5
.01
80+
150
0 - 125
150oF
3/4" NPT (F)
(2) 1/4" NPS (M)
(1) 1/4" NPS (M)
34 oz.
(1) HAR-507
1
1
18 lbs. 2 oz.
SB-6-148
5
.01
120+
150
0 - 125
150oF
3/4" NPT (F)
(4) 1/4" NPS (M)
(1) 1/4" NPS (M)
34 oz.
(2) HAR-507
2
1
21 lbs. 2 oz.
SB-6-148
* HAF-508 coalescer filter should be used in conjunction with a centrifugal type filter to remove
the majority of water, oil and dirt, prior to the coalescer filter.
CleanAir Three-Stage Desiccant Unit
DAD-500
Service Bulletin
SB-6-156-J
The three-stage desiccant unit
provides the ultimate in clean dry air.
First stage centrifugal filter removes
particulates to 5 microns. Stage two
coalescer filters down to .01 micron.
Third stage desiccant removes
remaining water vapor to a dew point
of -40oF.
• Ideally suited for low to medium
production.
• DAD-500 air-drying system includes
three filtering units, as well as a wall
mount bracket and desiccant filter
change indicator.
• Centrifugal and coalescer units
include automatic bowl drain
manually drain.
• Coalescer filter includes filter change
indicator
• Desiccant filter includes sight glass
indicator (Changes color when
desiccant needs replacement)
DAD-500 Desiccant Air Drying System
DESICCANT SYSTEM UNITS
DAD-500
HAF-502
HAF-505
AIR DRYING CENTRIFUGAL COALESCER
SYSTEM*
FILTER ONLY FILTER ONLY**
HAR-507
REGULATOR
ONLY
Air Inlet
1/2" NPT (F) 1/2" NPT (F) 1/2" NPT (F)
3/8" NPT (F)
Air Outlet
1/2" NPT (F) 1/2" NPT (F)1/2" NPT (F) 1/4" NPT (F)(3 ea)
Max. Operating Pressure (psi)
150
150
150
150
Replacement Filters/Desiccant DAD-1
HAF-6
HAF-28
—
Service Bulletin
SB-6-156
SB-6-146
SB-6-152
SB-6-147
Air Flow Capacity (cfm)
25
100
55
60
* Includes HAF-502, HAF-505 and HAR-506.
35
TM
WhirlWind In-Line Filter
The WhirlWind disposable in-line
filter attaches to the base of the spray
gun or air tool to remove any
remaining water, oil, dirt and rust
from the air line. This high-quality,
high-flow, solvent-resistant air filter
has a very low pressure drop and has
a floating filter that automatically
adjusts for changing air conditions.
• Air is swirled to trap droplets, then
filtered to absorb remaining
particulates.
• Multilayer design extends life, so unit
lasts up to 40% longer than other filters.
• Perfect for use with HVLP guns,
WhirlWind provides 55% more air flow
than other filters.
HAF-507-K12
HAF-507-K12 WhirlWind In-Line Filter
HOUSING
MATERIAL
PACKAGING
THREADS
Solvent-resistant
12 filters
1/4" NSP (M) inlet
Delrin® plastic per dispenser carton 1/4" NSP (F) inlet
MAXIMUM
OPERATING
PRESSURE
OPERATING
TEMPERATURES
125 psi
50oF - 110oF
PRESSURE DROP
LIQUID
@ 80 PSI w/ 20 SCFMCONTAMINANT
2 psi
SERVICE
BULLETIN
1.5 fl. oz. SI-8-10-1
CleanAir Air Regulators
HAR-502/505/535/555
Air Regulator
General purpose regulators for line
takeoff use or as integral regulators on
pumps, pressure tanks and other air
operated devices. Require separate trap
or filter in air line to remove moisture
or dirt.
• Unique three position, non-rising
adjusting knob.
• Removable plug and cap.
• All metal body; durable Delrin® cap
and knob; Buna N diaphragm and
disc.
• Accurate regulator mechanism
provides precision air control.
MODEL
HAR-501*
HAR-502
HAR-505
HAR-535
HAR-555
HAR-507
• Self-relieving design.
• Both main line and regulated outlets
available from same units.
HAR-501 Air Regulator
Extra Sensitive regulator for use
with precision control on pressure feed
tanks or other dead-end applications.
Can be used to control atomization
pressure for one spray gun.
• Self-relieving regulator.
• Tough, reinforced Buna N
diaphragm for extended service life.
• 100 mesh stainless steel strainer.
• Removable bottom plug for easy
service.
MAX.
REGULATED
MAX AIR
MAX
CAPACITY PRESS.RANGE INLET PRESS. OPERATING
CFM
PSI
PSI
TEMP OF
15
40
40
40
40
60
0 - 20
0 - 125
0 - 125
0 - 125
0 - 125
0 - 125
250
250
250
250
250
250
• Forged brass body and stainless steel
or brass internal parts for long
service.
• High ratio of diaphragm surface to
orifice area provides stable uniform
regulation.
120o
120 o
120 o
120o
120o
150o
DIMENSIONS
H" X W"
WEIGHT
LBS.
6 x 4-1/2
4-7/8 x 2 3/8
4-7/8 x 2-3/8
4-7/8 x 2-3/8
4-7/8 x 2-3/8
4-7/8 x 3
2-1/4
1-1/8
1-1/8
1-1/8
1-1/8
1-1/2
HAR-505
MAIN AIR INLET
PORT
SIZE
1
1
1
1
1
1
3/8"
1/4”
1-4”
3/8"
3/8"
3/8"
NPT
NPT
NPT
NPT
NPT
NPT
MAIN LINE OUTLET
PORT
SIZE
(F)
(F)
(F)
(F)
(F)
(F)
1 1/7” NPT (F)
1 1/4" NPT (F)
2,4 1/4" NPT (F)
-
HAR-501
REGULATED OUTLETS
PORT
SIZE
1
2
3
1
1
3
3/8" NPT (F)
1/4” NPT (F)
1/4”NPT (F)
3/8" NPT (F)
1/2" NPT (F)
1/4" NPT (F)
* Extra-sensitive regulator for precise control on pressure tanks and other dead-end applications.
** These models include nickel for corrosion protection. Other models are painted.
36
Air Control Accessories
GA Pressure Gauges
For accurate pressure readings,
standard gauges are made from
rust-resistant materials and include
glass covered dials. Can be used in
any location where conditions of
vibration or rough service exist.
GA-77 gauge is very accurate in low
pressure range and ideal for critical
pressure adjustments. Calibrated in
ounces from 0 to 10 lbs.; in pounds
from 10 to 30 lbs.
HARG-510
Service Bulletin - SB-6-105-D
• HARG-510 is a precise, lightweight
air regulator and gauge combination.
Fits any professional spray gun;
comfortable for left and right-handed
painters. Swivel adaptor allows fast
installation, and a lock-ring secures
pressure settings to avoid interruptions
for readjustments. Max. Air Inlet
Pressure: 400 psi
Outlet Pressure Adjust. Range:
5-100 psi
Gauge Port Size in Regulator:
1/8" NPT (F)
• HAV-500 and HAV-501 are precise
air adjustment valves that control
pressure at the spray gun. Fits all
professional spray guns. A swivel top
allows for easy and fast installation.
• P-H-5516 air adjustment accessory
attaches directly to the spray gun
air inlet. The large knurled knob
adjusts air flow. Commonly used with
spray guns, pressure tanks and pumps.
MODEL
SCALE (TYPE)
GA-73
GA-77
GA-288
GA-313
GA-316
GA-333
GA-338
0 - 30 psi (A, F)
0 - 30 psi (A, F)
0 - 160 psi (A, F)
0 - 15 psi (A)
0 - 160 psi (A)
0 - 100 psi (A, F)
0 - 160 psi (A)
THREAD
1/4"
1/4"
1/4"
1/8"
1/4"
1/4"
1/8"
NPT
NPT
NPT
NPT
NPT
NPT
NPT
DIAMETER
INLET
2"
3-1/2"
2"
1-1/2"
2"
2"
1-1/2"
Bottom
Bottom
Bottom
Bottom
Back
Bottom
Back
(M)
(M)
(M)
(M)
(M)
(M)
(M)
Air Regulator Lockout - HAR-400
This device allows the painter to est their air
regulators to guarantee proper atomization, as well
as to assure compliance in areas where air cap
pressure is limited to 10 PSI or less. Includes one
key per unit.
HAV-500
HAV-501
P-H-5516
Air Adjusting Valves
GAUGE
MODEL
AIR INLET
AIR OUTLET
HARG-510 1/4" NPS (M)
1/4" NPS (F)
(Nipple)
(Swivel Adapter)
HAV-500 1/4" NPS (M) 1/4" NPS (F) (Swivel)
HAV-501 1/4" NPS (M) 1/4" NPS (F) (Swivel)
P-H-5516 1/4" NPS (M) 1/4" NPS (F) (Swivel)
NET WT.
RANGE
TYPE
10 oz.
0 - 160 psi
3.5 oz.
5 oz.
3 oz.
n/a
0 - 160 psi
n/a
Diaphragm
Relieving
Straight
w/ Gauge
Straight
Air Valves
MODEL
DESCRIPTION
MAX. OPERATING
PRESSURE
MATERIAL
VA-527
VA-528
VA-540
VA-541
VA-542
3/8" NPS (M) x 3/8" NPT (M)
3/8” NPS (M) x 3/8” NPT (F)
3/8" NPS (M) x 3/8" NPT (M)
1/4" NPS (M) x 3/8" NPT (M)
1/4" NPS (M) x 1/4" NPT (M)
500
500
500
500
500
Stainless Steel
Stainless Steel
Brass
Brass
Brass
37
Air VizorTM
Breathable Air Systems
The World’s Most Technologically Advanced
Air Supplied Respirator.
•
•
•
•
•
•
•
•
•
Breathable Air Systems
Order No.
Model No.
Belt
Regulator
and Hood
Assembly
# of
Breathable Visor
Filtration
Air
Covers
Unit
Filtration
Hose (30’) Included Included Description
Yes
No
2
None
--------
Yes
Yes
12
DAD-504
Desiccant
Retrofit
System
Yes
Yes
12
DAD-503
Yes
Yes
12
HAF-601
•
Protects against isocyanate exposure.
Part of a complete breathable air system.*
NIOSH approved (TC 19C-0365) - meets OSHA
requirements.
Cool and comfortable.
Full lightweight face mask with excellent visibility.
- Ratchet adjustable headgear.
- Visor window improved to reduce glare
- Detachable hair and neck cover
- Rigid face piece for better visibility over time.
- Replaceable visor window and detachable fabric
face shield for economical servicing.
Easily accommodates prescription eyewear and bearded
employees.
Disposable carbon filter and pre-set tamper proof
regulator.
- 1,000 hour carbon cartridge life
Adjustable belt with quick fit buckle.
Quick connect between visor and waistbelt permits easy
removal of visor.
Air Vizor (MPV-625) includes:
- Full face mask
- Belt-mounted filter and regulator
- Breathing air tube
MPV-625
MPV-650
MPV-651
MPV-652
38
3-Stage
Filtration
with Desiccant
Air Dryer System
3-Stage
Filtration
System
* Air VizorTM requires proper air line filtration and carbon
monoxide (CO) monitoring to complete an approved
supplied air respirator. See next page for proper air line
filtration. A carbon monoxide (CO) monitor may be
purchased locally or from ENMET Corporation: (734)
761-1270 (phone). Order form F-1073-B available from
DeVilbiss upon request.
Air VizorTM
Breathable Air Filtration Units
DAD-503
•
•
•
•
•
•
•
•
•
•
•
Converts shop air into clean, dry,
contaminant-free air for breathing
systems and spray operations.
5 micron particulate filter (Stage 1)
.01 micron coalescing filter (Stage 2)
Charcoal filter for hydrocarbon and odor removal
(Stage 3)
28 CFM breathing air regulator
Desiccant system removes water vapor for spray
gun (rated for 25 CFM maximum flow)
60 CFM spray gun regulator
Automatic drains (Stages 1, 2 and 3)
Can be used with up to four Air Visors
1/2” NPT inlet
Refer to Service Bulletin (SB-6-159
HAF-601
•
•
•
•
•
•
•
•
•
•
•
Converts shop air into clean, contaminant-free air
for breathing systems and spray operations
5 micron particulate filter (Stage 1)
.01 micron coalescing filter (Stage 2)
(Stage 3)
28 CFM breathing air regulator
60 CFM spray gun regulator
Automatic drains (Stages 1, 2 and 3)
Wall-mount bracket
Can be used with up to four Air Vizors
1/2” NPT inlet
Refer to Service Bulletin SB-6-132
DAD-504
•
•
•
•
•
•
Converts a DAD-500 into a breathing air source
28 CFM breathing air regulator. Includes all
necessary fittings
Can be used with one Air Vizor
Automatic drain
Refer to Service Bulletin SB-6-176
39

Section A - DeVilbiss

Transcription

Similar documents

Your OWN LABEL food spray gun

A54-125 DeVilbiss AGMD Pro Brochure

jouranl 8 - Blue Valley Schools

Botique Fungus Pharm RTU 35oz 8-12-06.cdr

Home / SATA.COM

A54-113R FLG4 Sales Brochure 2-13

n Wew o/r flow technology * Unique new fluid tip design by SATA

thix watch

contact adhesive

Cozy Up to the Critter