Ultra-Rest Installation Instructions

INSTALLATION INSTRUCTIONS (Watch Instructional DVD)
FIG. 1
FIG. 3
OPERATION
Loading Arrow: Using Thumb
Wheel, rotate Launcher to
Arrow Capture Position while
nocking your arrow.
Manual Release: To reach
Drop Away Position without
firing your bow, rotate
Launcher to Full Draw Position
(90°) by pushing forward on
the Thumb Lever, continue
pushing forward and slide your
thumb off the Thumb Lever.
FIG. 7
Down Buss Ca
ble
Up Buss Cable
Timing Cord
FIG. 2
1
Fasten the Ultra-RestTM
to your bow riser using
a 3/16 Allen Wrench (not
included), Mounting Bolt,
and Washer from the
Parts Kit. (For additional
fastening, tighten the
Mounting Block Set
Screw.) (Fig.9)
2
Attach the Cable Clamp to
the downward traveling buss
cable. Use the #6-32x3/8
Panhead Phillips Head
Screw, and the #6-32 nut.
Engage Screw just one turn.
(Fig.9)
3
Arrow Capture
Position (80°)
Drop Away
Position (0°)
FIG. 8
(Fig.7) (Fig.8)
Thread the Timing Cord
through the remaining hole
in Cable Clamp from top
to bottom, then snug the
Screw. (Do not tighten
yet.) See [ADDITIONAL
ADJUSTMENTS] for additional
Timing Cord adjustment
located at the Thumbwheel.
FIG. 5
FIG. 4
Full Draw
Position (90°)
FIG. 6
ADDITIONAL ADJUSTMENTS
Additional Horizontal Adjustments:
(1) Move screws in Launcher to closest
holes toward end of shaft.
(2) Insert the Spacer Block and longer
#10-32x7/8 screw. (Fig.9)
Additional Vertical Adjustments:
If your arrows kick nock low and the
Launcher is receiving fletching contact
replace the standard Launcher with the
TL1 Launcher (1/8” higher), remember to
adjust nocking point accordingly. (Fig. 9)
Additional Timing Cord Adjustment
If any additional vertical, horizontal, or
mounting block adjustments are made,
use a 7/64 allen wrench to loosen
the #6-32x3/8 socket cap Cord Lock
Screw, located in the Thumb Wheel (5
turns). Adjust Timing Cord in or out to
ensure Full Draw Position or 90° (Fig.8)
is reached and Full Draw (90°) Indicator
Marks align at full draw. Tighten screw to
Lock Cord. (Fig.9)
Visit your local dealer for professional installation and arrow tuning.
FIG. 9
(3) TL1
Launcher
(optional)
1/8 inch
higher in
the valley
4
Slide the Timing Cord and
Cable Clamp down the buss
cable at least 3 inches below
the rest. Put enough tension
on the Cord to hold the
Launcher in the Full Draw
Position(90°). Then tighten
the Clamp enough to hold
the Launcher in the Full Draw
Position but loose enough
that the Clamp can slide up
and down the buss cable.
DO NOT TIGHTEN YET!
CAUTION!
5
The Cable Clamp MUST
be able to slide in this step.
With the cord holding the
Launcher in the Full Draw
Position (90°), draw the
bow. The Cable Clamp will
slide up the buss cable
and self adjust to correct
location. Slowly let down
bow, then tighten the Cable
Clamp Screws. Timing is
now complete.Tune the rest
then apply Felt. (Fig.9)
FIG.10
At full draw, the
Full Draw Indicator Marks
must align.
At full draw, the Full Draw Indicator Marks must align.
6
To ensure proper timing when
the bow is drawn, the launcher
should move from the capture
position to
the full draw
position within
the last couple
inches of the
draw cycle.
Excessive
Timing Cord
tension
may cause
undesirable
results.
NOTES: 1) Cable Clamp
location MUST be at least
three inches below the
Ultra-Rest.TM 2) Lower Clamp
locations allow Ultra-RestTM
to fall away sooner. (3) Repeat
steps 4 thru 6 if any additional
Vertical, Horizontal, or Mounting
Block adjustments are made.
Felt
Arrow Capture
Bar
(2) Longer Vertical
Adjust Screw
(optional, used with
Spacer Block)
#10-32x7/8
Mounting
Block
Short Vertical
Adjust Screw
(Standard)
#10-32x5/8
Launcher
(Standard)
Mounting Block
Set Screw
#10-32x3/8
(optional)
(2) Spacer Block
(optional)
(1) (optional position
towards end of
shaft)
Mounting
Bolt 5/16x1
Washer
(4) Timing Cord Lock Screw
(optional adjustment for timing
cord) #6-32x3/8 screw
Horizontal
Adjust
Screw
Full Draw Indicators
Thumb Wheel Lever
Allen Wrench
(for horizontal and
vertical adjustment)
#6-32 nut
#6-32x3/8
Screw
Timing Cord
Cable Clamp
TM
fastest nocks on the planet!
TM
TM
Check out other products and HIGH SPEED VIDEO of the Ultra-Rest™ at www.qadinc.com
#1 selling nocking loop!