Companion Table - mirrorlifestyle

PANTONE 072 C
PANTONE 123 C
Paper weight 60gsm
IMPORTANT SAFETY INSTRUCTIONS
When installing the Companion Table, basic precautions should always be followed, all the
instructions should be read and kept for future reference.
DISPOSAL
• Please respect the environment!
• Dispose of the packaging according to the local recycling regulations.
• Dispose of paper and cardboard packaging separately from plastic bags into the corresponding
containers.
• Dispose of the appliance at the end of its life span according to local recycling regulations.
Companion Table
INSTRUCTION MANUAL
WARNING
This product is intended for domestic use only.
TECHNICAL SPECIFICATION
Maximum load: Top shelf: 50lbs (23kg), Middle Shelf 25lbs (11kg), Bottom Shelf 50lbs (23kg)
Measurements: H53xW63xD38cm
NOTE
Flat pack furniture is non-refundable once assembly has commenced. Please check the contents
of this pack against the instructions enclosed to make sure all the fixings and panels are
undamaged and all correct.
Model No. EL1190
Imported and distributed by Easylife Group Ltd, London NW1 0JP
Customer service: 0871 855 6100
Please read carefully before use and keep for future reference
For more innovative products from Easylife please visit:
www.easylifegroup.com
IN1190-1 © 2013 Easylife Group Ltd
Customer service: 0871 855 6100
For more innovative products from Easylife please visit:
www.easylifegroup.com
PANTONE 072 C
PANTONE 123 C
Paper weight 60gsm
Dear Customer
Thank you for purchasing the Companion Table.
Organise all your living room or bedside clutter with our thoughtfully designed
companion table. Two sides hold your TV guides and magazines, two shelves organise
your coffee table books, whilst a neat little drawer on smooth runners will hide remote
controls, crossword pen, glasses etc. Supplied in a walnut finish, it requires simple
home assembly. Measures H53xW63xD38cm.
Step 1
Position bottom panel (G) on a flat surface. It is recommended in order to protect the companion table
throughout assembly and avoid damaging the wood / veneer finish you assemble on a carpet surface
or unfold the cardboard packaging the table is delivered in.
Attach magazine side panel (A&C) to bottom panel (G) using 4 x screws (U) and secure in place as
shown.
Slide into position magazine front panel (E) into the pre-set groves in panels A,C & G (as shown).
Slide magazine back panel (F) into the pre-set groves in panels A, C & G (as shown). Make sure the
drawer runner is in the correct position at the top when you slide the panel into place.
ASSEMBLY
Customer service: 0871 855 6100
For more innovative products from Easylife please visit:
www.easylifegroup.com
PANTONE 072 C
PANTONE 123 C
Paper weight 60gsm
Step 2
Attach the magazine side panels (B&D) to the opposite side of the bottom panel (G) using 4 x screws
(U) and secure in place (as shown). Slide into position magazine front panel (E) into the pre-set groves
in panels B,D & G (as shown).
Slide into position magazine front panel (E) into the pre-set groves in panels B, D & G (as shown). Slide magazine back panel (F) into the pre-set groves in panels B, D & G (as shown). Make sure the
drawer runner is in the correct position at the top when you slide the panel into place
Step 4
Carefully turn top panel (I) over 180° and position in place on top of all 4 x magazine side panels (A,B,C
& D). Each cam bolt (Q) will slide into position in the pre-set holes in all four panels. Please ensure that
the two magazine back panels (F) slide into the pre-set groove in the top panel (I).
Position in place all 8 cam locks (R) into the pre-set holes in the magazine side panels (A,B,C & D) and
secure in place by turning each screw one half turn clockwise (180°) with a screwdriver to lock the cam
bolt and top panel (I) in place.
Step 3
Position the top panel (I) on a flat surface and secure in place 8 x cam bolts (Q) as shown in the pre-set
screw holes with a screwdriver
Customer service: 0871 855 6100
For more innovative products from Easylife please visit:
www.easylifegroup.com
PANTONE 072 C
PANTONE 123 C
Step 5
Paper weight 60gsm
Attach drawer panel (H) using 4 x screws (S) to back of companion table in the pre-set holes which can
be located on the side magazine panels C&D.
Carefully position the table on its front and attach all 4 castors (O) using 4 x castor screws (V) in the preset screw holes in the bottom panel (G). Carefully re-position the table in its correct standing position
once completed.
Step 6
Position in place the middle shelf (N) as shown.
Step 7
Attach drawer side panels (K) and drawer back panel (L) together using 4 x screws (S). Slide into the
pre-set groves the drawer bottom panel (M) and attach the drawer front panel (J) using 4 x screws (T)
as shown.
Attach drawer handle (P) using 1 x screw (T) to the drawer front panel (J) as shown. The drawer is now
complete and can be positioned in place.
The companion table is now complete and ready to use.
Cleaning
• Wipe clean with a soft damp cloth
• Maintain using any furniture household polish
• Do not get wet, wipe any spillages immediately to avoid stains and damage to the table.
Packaging
• Dispose of the packaging at your local recycling centre
• Dispose of paper and carton separately from the polyfoam protective packaging at your
local recycling centre
• Dispose of the item at the end of its lifespan at your local authorised household waste
recycling centre.
Customer service: 0871 855 6100
For more innovative products from Easylife please visit:
www.easylifegroup.com