Multi EL Desk (Electric Version)

biomorph
®
multi EL desk
electric versio n
USER SIDE
Ground Support Equipment (US) ltd., DBA biomorph, 11 Broadway, New York, NY 10004. 888 302 3375 fax: 212 809 4324 info@biomorphdesk.com
biomorph
interactive desk
electric
®
multi
ASSEMBLY INSTRUCTIONS
Questions? Call 888 302 DESK
For info visit www.biomorph.com
frame assembly
Please use the instructions
enclosed with the frame & page2
top assembly
TOOL
Screw gun w/philips bit
6
remove desktops from crate
1
Place desktops upside
down on clean floor.
assemble keyboard mech
2
Packed in smallest carton
with hardware.Use enclosed
instructions to assemble only.
3/4" screw x 6
3
Use to attach keyboard
mech to keyboard surface.
Use pilot holes on bottom
of surface.
!
kb
IMPORTANT
DO NOT OVERDRIVE SCREWS
turn main desktop over
4
Place desktop ontop of
frame assy. and use location
holes on surface
to position frame
3/4" silver screws x 16
Use to attach desktop
to support plates from
underneath. Drive directly
into surface. Fill all holes.
5
!
!
The completed desk is very
heavy and must not be moved by
lifting the surface alone, otherwise
damage may occur.
attach controller box,
adjustment control switch
wire guide clips
8
Found with frame. Screw into
surface with supplied screws
using pilot holes. Connect wires
as per frame assy sheet.
privacy/modesty panel
attachment pilot holes
Use to route wires under
surface.Screw directly into
surface with supplied screws.
use location holes on underside of top to position on frame
controller box
7
DO NOT OVERDRIVE SCREWS
1 1/2" black hex-head nut-bolt sets x 8
found in crate w/tops
6
optional CPU holder
7
THROUGH-HOLES FOR BLACK HEX-HEAD
NUT-BOLT SETS
Place grommets in 3 holes.
use for wire management.
remove to mount add-ons.
PILOT HOLES FOR 3/4” SCREWS
UNDERSIDE OF DESKTOPS
GROUND SUPPORT EQUIPMENT (U.S.) Ltd.
11 Broadway, space 905, New York, NY 10004, U.S.A.
Tel: 888 302 DESK. (212) 809-4323 Fax:(212) 809-4324.
Email: info@biomorphdesk.com
You are hereby made aware that the content of any
material submitted to you [upon your request] by
Biomorph/Ground Support Equ. (US) Ltd. in connection
with its furniture designs is considered proprietary to
Biomorph/Ground Support Equ. (US) Ltd. and protected
under federal copyright, trademark and patent laws, and
under federaland state unfair competition law.
Unauthorized copying, dissemination and/or use, both
unintentional and intentional may subject you to payment
of damages through legal action. © 2003
Biomorph/Ground Support Equ. (US) Ltd.
grommet holes
frame
Use to attach keyboard
mechanism/small surface
assembly to main surface.
Insert into thru-holes from top
of large surface. Screw tight.
plastic grommets x 3
9
keyboard surface adjustment lever.
squeeze to release, let go to lock.
adjustment control switch
keyboard surface tilt knob
3
keyboard
surface
adjustment
mechanism
Operation of the DPF1C “one reference”
DPF1C - Desk Panel
V
V
= Parallel up
= Parallel down
S
= Store memory
•
••
•••
= Memory 1
= Memory 2
= Memory 3
V
Up and down ( V):
Just activate either the up or down button for parallel drive and the system will drive until the button is
released again or the system reaches end position.
Memory:
The four small buttons are used for memory drive/storing memory.
Store memory
• Press S – button, the display will flash for 2 seconds
• Within these two seconds press one of the small buttons with dots and the position will be stored at this
button.
• The panel will acknowledge by showing “1”, “2” or “3” in the display depending on chosen position
Memory drive (small buttons with dots)
Press one of the memory buttons and the system will start driving to the pre-programmed memory position.
Keep the button pressed until the position is reached.
Display function
Shows the actual height in either cm or inch.
Page 16 of 36