fuel system parts
Transcription
fuel system parts
Fuel/Carb Section (C) Version 01 March/05 FUEL SYSTEM PARTS MANUAL PETCOCK TO REPLACE VACUUM TYPES USED ON 78-84 XS650's Petcocks - Non Vacuum type to replace 78-84 vacuum type petcocks. All 1978-84 North American market 650's have original petcocks operated by Vacuum from a line to the intake (on carb holder). 1978-79 models have 2 and 1980-84 models have 1 petcock. Vacuum petcocks are chronic leakers and are all getting to the point of being non-repairable. Our petcock is the Early type 650 manual petcock with a wider flange cast on it so it will fit in place of the vacuum types. Our Petcock fits to right or left and each comes with the tap to tank O-Ring seal and assorted outlet fittings ( petcock has 2 outlet ports). Fittings included: 2 ninety degree, 1 Straight fitting & 1 outlet port Plug. There is an "ON", "OFF and "Reserve" position. XS# 20-0019 .... $40.00 each BLIND PLUG Blind Plug - Carb Holder Air Barb OEM Ref. # 1J7-13569-00 Fits: XS650 stock carb holders & blocks off air barbs when vacuum petcocks are replaced with manual type petcocks. Order quantity needed. XS# 48-1447 ...... $1.50ea. SEALING WASHERS & PETCOCK MOUNT SCREWS Tap to Tank sealing Washers and Mount Screws. Fits All 650's 70-84 XS# 20-0020 ..... $1.50/set OUTLET FITTINGS Petcock 90 degree outlet fitting Replacement fittings - Fits:XS 650 Petcocks #20-0019/0050/0051 XS# 20-6420 ..... $3.00ea. PETCOCK FILTER SET Petcock Fuel Pipe Filter Set (2) Filter set - Replacements for #20-0019 petcocks and will also fit 1970-77 stock petcocks XS# 20-6419 .. $2.00/pk/2. 48 FUEL SYSTEM PARTS Fuel/Carb Section (C) Version 01 March/05 PETCOCK - MANUAL TYPE Petcock - Original Non Vacuum Manual type - (3 screw rear cover) Includes Tap to Tank O-Ring. Will replace all original non-Vacuum types used on 1970-77 650's. <<< Petcock - LH - XS# 20-0050 $38.00 each Petcock - RH - XS# 20-0051 >>> PETCOCK MOUNT O-RING Tap to Tank O-Ring - Fits: Petcocks on 70-77 650's XS# 20-0015 .... $4.00ea. PETCOCK REAR GASKET Petcock Rear Cover Gasket - (3 Hole) OEM# 447-24522-00 Fits: TX/XS650's SEALING WASHERS 1973-77 + our #20-0019 petcocks. Tap to Tank sealing Washers. XS# 20-0053 .... $5.00ea. Fit under mount screws on 70-84 650's XS# 20-0018 ..... $0.50/pr. PETCOCK REBUILD KIT Petcock Rebuild kit - Fits: TX650/A 73-74, XS650B/C/D 75-77. These petcocks have a 3 screw rear cover plate.Kit contains: 1pc. Valve Rubber, 1pc. Wave Washer, 1pc. Tap to tank O-Ring, 2pc. Tank bolt Washer, 1pc. Drain screw Gasket, 1 pc. Rear cover Gasket ( 3 Screw ). XS# 20-0014 ...... $15.00/kit 49 PETCOCK REAR GASKET Petcock Rear Cover Gasket - (2 Hole) OEM Ref.# 256-24522-00 Fits: TX/XS650's (usually on 1970-72). XS# 20-0052 .... $5.00ea. PETCOCK REBUILD KIT Petcock Rebuild kit - Fits: XS1/XS1B/XS2 70-72 These petcocks have a 2 screw rear cover plate. Kit contains: 1pc. Valve Rubber, 1pc. Wave Washer, 1pc. Tap to tank O-Ring, 2pc. Tank bolt Washer, 1pc. Drain screw Gasket, 1 pc.Rear cover Gasket ( 2 Screw) XS# 20-0049 ..$15.00/kit Fuel/Carb Section (C) Version 01 March/05 FUEL SYSTEM PARTS GAS CAP WITH KEYS GAS CAP WITH KEYS Gas Cap - Fits: XS650 "Standard" models 1976-79 XS# 20-0033 .... $30.00ea. OEM Ref.# 584-26402-00 Gas Cap - Fits: XS650 "Special" models 1978-84 XS# 20-0034 .... $34.00ea. OEM Ref.# 2M0/4R0-24600 GAS CAP SEAL GAS CAP SEAL Gas cap rubber Seal - Fits: All 1976-84 XS650 gas caps. XS# 20-0036 ..... $4.00ea. Gas cap Seal - Fits: All 1974-75 XS/TX 650 gas caps. Oem Ref.# 341-24612-01 XS# 20-0038 ... $8.00ea. FUEL TAP to TANK O-RING Fits: Stock Vacuum Petcocks on 78E Standard model Only! XS# 20-0017 ..... 4.00ea. FUEL TAP MOUNT O-RING Tap to Tank O-Ring- Fits: Stock Vacuum Petcock on XS650 78-84 models Except 78E Std. XS # 20-0016 .. $2.00ea. PETCOCK MOUNT O-RING Tap to Tank O-Ring - Fits: Petcocks on 70-77 650's XS# 20-0015 .... $4.00ea. INLINE FUEL FILTER Clear square inline Fuel Filter XS# 20-0013 .. $2.00ea. 50 CARB PARTS BRASS CARB FLOAT Fuel/Carb Section (C) Version 01 March/05 CARB FLOAT Brass Carb Float - Fits: 70-79 XS Stock 38mm. CV Carbs Oem Ref.# 256-14985-00 XS# 20-6500 .... $12.00ea. Plastic Carb Float - Fits: 80-84 XS Stock 34mm.CV Carbs Oem Ref.# 3H5-14985-00 XS# 20-6502 .... $12.00ea. also replaces Brass float used on early 1980 650 specials FLOAT BOWL GASKET FLOAT BOWL GASKET Gasket - Float Bowl - Fits: 80-84 Stock 34mm XS CV Carbs Oem Ref.# 3F7-14984-00 XS# 20-5020 .... $4.00ea. Gasket - Float Bowl - Fits: 70-79 Stock 38mm. CV Carbs Oem Ref.# 256-14984-00 XS# 20-7029 .... $4.00ea. FLOAT BOWL DRAIN PLUG FLOAT BOWL DRAIN SCREW Float Bowl Drain Plug - Fits:70-79 Stock 38mm. CV Carbs. XS# 48-0779 .... $3.00ea. Float Bowl Drain Screw with O-Ring - Fits:80-84 XS Stock 34mm. CV Carbs. XS# 48-0778 .... $4.00ea. FUEL LINE BRASS FUEL LINE T T-Piece - ( Fuel supply T pipe that fits between carbs ) Fits: 80-84 34mm. CV carbs. XS# 48-0884 .... $15.00ea. Black Rubber Fuel Line - (original thin wall type) 1/4" ID (6mm.) - 1pc. x 11.5" XS# 20-4010 ..... $1.00/pc. 51 CARB PARTS Fuel/Carb Section (C) Version 01 March/05 CARB CHOKE PLUNGER CARB CHOKE PLUNGER Carb Choke Plunger - Fits: 1980-84 stock Carb Choke Plunger - Fits: XS1/XS1B CV Carbs. XS# 48-0775 ..... $12.00ea. (1970-71) OEM Ref.# 603-14171-00 XS# 48-2009 ..... $8.00ea. CARB CHOKE PLUNGER Carb Choke Plunger - Fits: Stock BS38 CV Carbs as on XS2/TX650/ TX650A/XS650B (1972-75 Only! ) XS# 48-2002 ...... $8.00ea. CARB CHOKE PLUNGER Carb Choke Plunger - Fits: XS650C/ D/E/SE/F/2F/SF (1976-79) XS# 48-2012 ..... $8.00ea. 48-5040 48-5041 CHOKE PLUNGER SEAL - Carb Choke Plunger Dust Seal XS# 48-5040 Fits: 80-84 650's .... $2.00ea. XS# 48-5041 Fits: 70-79 650's .... $2.00ea. CARB CHOKE PLUNGER Carb Choke Plunger - Mikuni VM18/144 type - Fits: Mikuni Round slide VM 30- 44mm. carbs with lever type (vertical pull) choke plunger. XS# 48-2005 .... $8.00ea. CARB CHOKE BODY GASKET 7 Hole - XS# 48-2010 ... $2.00ea. - Fits: TX650A, XS650B (74-75) 8 Hole - XS# 48-2011 .... $2.00ea. - Fits: XS650XS650C/D/E/F/2F/SF (76-79) Note: 1970-73 models do not use a choke body gasket. 52 CARB PARTS FLOAT VALVE Float Valve - 10mm. Threaded type Fits: XS1/XS1B (1970-71) XS# 48-1429 .. $8.00ea. FLOAT VALVE Carb Float Valve - threaded type Fits: XS2 (72), TX650/A (73-74), XS650B-F (75-79) XS# 48-5019 .... $8.00ea. Fuel/Carb Section (C) Version 01 March/05 FLOAT VALVE Carb Float Valve - Push in with O-Ring seal, needle & clip. Fits: Stock CV carbs XS650G-K (1980-84) Specials. XS# 48-1445 .... $10.00ea. FLOAT NEEDLE SEAL -THROTTLE SHAFT Float Needle with clip - Fits: XS650G-K (80-84) 34mm. CV Carbs - Viton tipped Needle Only XS# 48-5014 .. $4.00ea. Seal - Throttle butterfly shaft Fits: 1970-79 XS BS38 CV Carbs. XS# 48-5021 ..... $5.00ea. CV CARB SLIDE/DIAPHRAGM ASSEMBLY CV CARB SLIDE/DIAPHRAGM ASSEMBLY Carb Slide & Diaphragm Assy. - Fits: Mikuni BS38 CV Carbs as used on 1970-77 XS/TX 650's OEM# 256-14940 Mikuni Genuine XS# 20-6029 .... $69.00ea. Carb Slide & Diaphragm Assy. - Fits: Mikuni BS34 CV Carbs as used on 1980-84 XS650's OEM# 3F7/3H5-14940 Mikuni Genuine XS# 20-6028 .... $64.00ea. Notes: Carb slides for 1978-79 XS650's are Not interchangeable with other slides as the needle retainer differs. Slides should be replaced if the diaphragms are torn or if the slide body rotates from the diaphragm (is loosened). 53 CARB JETS Fuel/Carb Section (C) Version 01 March/05 Jets Sold in multiples 48-0100 Series $ 6.00Pr. Main Jet - Large Round Type - N100/604 Mikuni - of 2pc. each size Only Fits: Most 80-84 Stock XS650 Mikuni 34mm. CV carbs - Main Jet OEM # 620-1423148-0111 #115 Main Jet - Large Round Type - N100/604 Mikuni 48-0113 #120 Main Jet - Large Round Type - N100/604 Mikuni 48-0115 #125 Main Jet - Large Round Type - N100/604 Mikuni 48-0116 #127.5 Main Jet - Large Round Type - N100/604 Mikuni 48-0117 #130 Main Jet - Large Round Type - N100/604 Mikuni 48-0118 #132.5 Main Jet - Large Round Type - N100/604 Mikuni Main Jet 48-0119 #135 Main Jet - Large Round Type - N100/604 Mikuni - Large Round Type 48-0120 #137.5 Main Jet - Large Round Type - N100/604 Mikuni - N100/604 Mikuni 48-0121 #140 Main Jet - Large Round Type - N100/604 Mikuni Note: Average Standard size for 48-0122 #142.5 Main Jet - Large Round Type - N100/604 Mikuni XS650 G/SG/H/SH/SJ/SK/SL (80-84) 48-0123 #145 Main Jet - Large Round Type - N100/604 Mikuni is #132.5 48-0124 #147.5 Main Jet - Large Round Type - N100/604 Mikuni 48-0125 #150 Main Jet - Large Round Type - N100/604 Mikuni 48-0126 #152.5 Main Jet - Large Round Type - N100/604 Mikuni 48-0127 #155 Main Jet - Large Round Type - N100/604 Mikuni 48-0128 #157.5 Main Jet - Large Round Type - N100/604 Mikuni 48-0129 #160 Main Jet - Large Round Type - N100/604 Mikuni Main Jet Washer - Fits: 1980-84 CV carbs (Fits under main Jet ) XS# 48-0199 .. $1.00ea. 48-0200 Series $ 6.00Pr. Main Jet - Small Round Type - N102/221 Fits: All 1970-79 XS/TX650 Mikuni BS38 CV carbs - Jet # 256-14944 also used as the Air Jet on all 1980-84 XS650G-K 34mm. OEM Mikuni CV carbs. XS# 48-0206 #115 Main Jet - Small Round Type - N102/221 Mikuni XS# 48-0208 #120 Main Jet - Small Round Type - N102/221 Mikuni XS# 48-0209 #122.5 Main Jet - Small Round Type - N102/221 Mikuni XS# 48-0210 #125 Main Jet - Small Round Type - N102/221 Mikuni XS# 48-0211 #127.5 Main Jet - Small Round Type - N102/221 Mikuni XS# 48-0212 #130 Main Jet - Small Round Type - N102/221 Mikuni Main Jet XS# 48-0213 #132.5 Main Jet - Small Round Type - N102/221 Mikuni - Small Round Type XS# 48-0214 #135 Main Jet - Small Round Type - N102/221 Mikuni N102/221 Mikuni XS# 48-0215 #137.5 Main Jet - Small Round Type - N102/221 Mikuni XS# 48-0216 #140 Main Jet - Small Round Type - N102/221 Mikuni XS# 48-0217 #142.5 Main Jet - Small Round Type - N102/221 Mikuni XS# 48-0218 #145 Main Jet - Small Round Type - N102/221 Mikuni XS# 48-0219 #147.5 Main Jet - Small Round Type - N102/221 Mikuni XS# 48-0220 #150 Main Jet - Small Round Type - N102/221 Mikuni XS# 48-0221 #152.5 Main Jet - Small Round Type - N102/221 Mikuni XS# 48-0222 #155 Main Jet - Small Round Type - N102/221 Mikuni XS# 48-0223 #157.5 Main Jet - Small Round Type - N102/221 Mikuni XS# 48-0224 #160 Main Jet - Small Round Type - N102/221 Mikuni Main Jet average Standard Sizes for 70-79 XS/TX650 - Stock 38mm. CV Carbs #130 #127.5 #122.5 #135 - XS1/XS1B/XS2/TX650 (1970-73) - TX650A/XS650B (1974-75) - XS650C/D (1976-77) - XS650E/SE/F/SF/2F (1978-79) 54 Air Jet for 1980-84 XS650 Stock CV Carbs Standard Size is #135 (N102/221 Type) CARB JETS 48-0300 Series $ 6.00Pr. 48-0313 48-0314 48-0315 48-0316 48-0317 48-0318 48-0319 48-0320 48-0321 48-0322 48-0323 48-0324 48-0325 48-0326 48-0327 48-0328 #150 #155 #160 #165 #170 #175 #180 #185 #190 #195 #200 #210 #220 #230 #240 #250 Main Jet - Large Hex Type - 4/042 Mikuni Fits: All Mikuni VM roundslide aftermarket carbs and most Mikuni TM Flatslide Carbs. Main Jet - Large Hex Type - 4/042 Mikuni Main Jet - Large Hex Type - 4/042 Mikuni Jets Sold in multiMain Jet - Large Hex Type - 4/042 Mikuni ples Main Jet - Large Hex Type - 4/042 Mikuni Main Jet - Large Hex Type - 4/042 Mikuni Main Jet - Large Hex Type - 4/042 Mikuni Main Jet - Large Hex Type - 4/042 Mikuni Main Jet - Large Hex Type - 4/042 Mikuni Main Jet - Large Hex Type - 4/042 Mikuni Main Jet - Large Hex Type - 4/042 Mikuni Main Jet - Large Hex Type - 4/042 Mikuni Main Jet - Large Hex Type - 4/042 Mikuni Main Jet - Large Hex Type - 4/042 Mikuni Main Jet Main Jet - Large Hex Type - 4/042 Mikuni - Large Hex Type Main Jet - Large Hex Type - 4/042 Mikuni 4/042 Mikuni Main Jet - Large Hex Type - 4/042 Mikuni 48-0500 Series $ 6.00Pr. 48-0501 48-0502 48-0503 48-0504 48-0505 48-0506 48-0507 48-0508 48-0509 48-0510 48-0511 Fuel/Carb Section (C) Version 01 March/05 Pilot Jet - VM22/210 Mikuni Type Fits: BS 38 CV carbs on XS650's C-F (76-79) and Aftermarket Mikuni VM roundslide carbs + most TM Flatslide carbs. #15 Pilot Jet - VM22/210 Mikuni Type #17.5 Pilot Jet - VM22/210 Mikuni Type #20 Pilot Jet - VM22/210 Mikuni Type #22.5 Pilot Jet - VM22/210 Mikuni Type #25 Pilot Jet - VM22/210 Mikuni Type #27.5 Pilot Jet - VM22/210 Mikuni Type #30 Pilot Jet - VM22/210 Mikuni Type Pilot Jet - VM22/210 Type #35 Pilot Jet - VM22/210 Mikuni Type Note: Average Standard size for #40 Pilot Jet - VM22/210 Mikuni Type XS650C/D (76-77) - #25 #45 Pilot Jet - VM22/210 Mikuni Type XS650E/SE (78), F/SF/2F(79) - 27.5 #50 Pilot Jet - VM22/210 Mikuni Type 55 CARB JETS/PARTS Fuel/Carb Section (C) Version 01 March/05 Jets Sold in multiples Pilot Jet - BS30/96 Mikuni Type of 2pc. each size Only Fits: 70-75 & 80-84 650's (34 & 38mm. Mikuni CV carbs) 48-0601 #30 Pilot Jet - BS30/96 Mikuni Type 48-0603 #35 Pilot Jet - BS30/96 Mikuni Type 48-0604 #37.5 Pilot Jet - BS30/96 Mikuni Type 48-0605 #40 Pilot Jet - BS30/96 Mikuni Type 48-0606 #42.5 Pilot Jet - BS30/96 Mikuni Type 48-0607 #45 Pilot Jet - BS30/96 Mikuni Type 48-0608 #47.5 Pilot Jet - BS30/96 Mikuni Type 48-0609 #50 Pilot Jet - BS30/96 Mikuni Type Pilot Jet - BS30/96 Mikuni Type Note: Average Standard size for XS1(70), TX650A (74), XS650B (75) - #45 XS1B (71), XS2 (72), TX650 (73), XS650G/SG (80), XS650H/SH/SJ/SK/SL (81-84) - #42.5 48-0600 Series $6.00pr.. 48-0900 Series $6.00pr.. 48-0901 48-0902 48-0903 48-0904 48-0905 48-0906 48-0907 Pilot Jet - VM28/486 Mikuni Type Fits: TM36-68 36mm. Flatslide Four-stroke Smoothbore Carb with accelerator pump and bellcrank type slide mechanism. #15 Pilot Jet - VM28/486 Mikuni Type #17.5 Pilot Jet - VM28/486 Mikuni Type #20 Pilot Jet - VM28/486 Mikuni Type #22.5 Pilot Jet - VM28/486 Mikuni Type #25 Pilot Jet - VM28/486 Mikuni Type #27.5 Pilot Jet - VM28/486 Mikuni Type Pilot Jet - VM28/486 Mikuni Type #30 Pilot Jet - VM28/486 Mikuni Type MIXTURE SCREW KIT PASSAGE PLUG Rubber pilot jet Passage Plug (pk./2) Fits: XS650G/H/SH/SJ/SK/SL (1980-84) stock BS34 CV Carbs. Used inside float bowl to seal pilot jet passage - 1 per carb XS# 48-5002 ..... $3.00/pk./2 IDLE MIXTURE SCREW Kit - mixture screw Washer, O-Ring & Blind Plug - Fits: XS650G/H/SH/SJ/SK/SL Fuel Idle Mixture Screw with Spring washer (1980-84) stock BS34 CV Carbs. and O-Ring - Fits: Stock BS34 CV Carbs on Plug covers vertical recessed idle mixture XS650G/H/SH/SJ/SK/SL (1980-84) XS# screw & keeps out contaminants. 48-5011 ..... $10.00ea. O-Ring fits under metal Washer at bottom of mixture screw hole and the engine will not idle properly if it is not present (O-ring is often disintegrated). XS# 48-5012 ..... $4.00/kit IDLE MIXTURE SCREW IDLE MIXTURE SCREW Fuel Idle Mixture Screw - (256 type) - Fits: Fuel Idle Mixture Screw - (584 type) - Fits: XS1/XS1B/XS2/TX650/TX650A/XS650B XS650C/D (1976-77) stock BS38 CV Carbs. (1970-75) stock BS38 CV Carbs. XS# 48-5009 .... $4.00ea. XS# 48-5008 .... $4.00ea. 56 IDLE MIXTURE SCREW Fuel Idle Mixture Screw with O-Ring - Fits: XS650E/SE/F/SF/2F(78-79)stock BS38 CV Carbs. XS# 48-5010 .. $9.00ea. CARB PARTS JET NEEDLE - 4JN19 NEEDLE JET - Z 6 Fuel/Carb Section (C) Version 01 March/05 JET NEEDLE - 4N8 Jet Needle - 4JN19 - Fits: XS1/XS1B/ Needle JET - Z 6 - Fits: XS1/XS1B/XS2/ Jet Needle - 4N8 - Fits: TX650A/XS650B XS2/TX650(70-73) stock BS38 CV Carbs TX650/A,XS650B (1970-75) stock BS38 (1974-75) stock BS38 CV Carbs. XS# 48-0653 ... $4.00ea. CV Carbs. XS# 48-0654 .... $12.00ea. XS# 48-0655 ..... $4.00ea. NEEDLE JET - Z 8 Jet Needle - Z 8 - Fits: XS650C/D (197677) stock BS38 CV Carbs. XS# 48-0656 ..... $12.00ea. JET NEEDLE - 4M1 NEEDLE JET - Z 2 NEEDLE JET - Y-O Jet Needle - Z 2 - Fits: XS650E/SE(78), XS650F/SF/2F(79) stock BS38 CV carbs Jet Needle - Y-O - Fits: XS650G/H/SH/ SJ/SK/SL(80-84)stock BS34 CV Carbs. XS# 48-0658 ..... $12.00ea. XS# 48-0660 ..... $12.00ea. JET NEEDLE - 502 JET NEEDLE - 5HX12 Jet Needle - 4M1 - Fits: XS650C/D (1976- Jet Needle - 502 - Fits: XS650E/SE(78), Jet Needle - 5HX12 - Fits:XS650G/H/ XS650F/SF/2F(1979) stock BS38 CV SH/SJ/SK/SL (1980-84) stock BS34 CV 77) stock BS38 CV Carbs. Carbs. XS# 48-0659 ..... $4.00ea. Carbs. XS# 48-0661 ..... $4.00ea. XS# 48-0657 ..... $4.00ea. NEEDLE JET O-RING O-Ring - Needle Jet (nozzle main) Fits: All XS/TX 650 (1970-79) stock BS38 CV Carbs. XS# 48-5020 .... $1.50ea. CARB SCREWS Screws - 5mm. (no lock washers) Late CV Lid Screw - Ref.# 26 Pk./4 XS# 48-0992 .... $2.00/Pk.4 Screws - 5mm. - Early CV Lid & Late CV Bowl Screw Ref.# 26&17 Pk./4 screws with lockwashers XS# 48-0991 ... $2.00/Pk.4 Screws - 4mm. Early CV Bowl Screw - Ref.# 17 Pk.4 with lockwashers XS# 48-0993 ..... $2.00/Pk.4 Screws - 6mm. - Carb Link bar Screw - Ref.# 68 Set of 4 with lockwashers XS# 48-0990 ... $2.00/Set/4 57 Fuel/Carb Section (C) Version 01 March/05 CARB REBUILT KITS Carb Rebuild Kits Rebuild 1 Carb Only - Order 2 per Bike CARB REBUILD KIT Carb Rebuild Kit - Fits: XS650SG-SL (1980-84) stock 34mm. CV carbs Kit Contains : Push-in Float Valve assembly with O-Ring, Carb rubber CARB REBUILD KIT passage plug & Float bowl gasket Carb Rebuild Kit - Fits: XS650C/D (19763F7 77) Kit Contains: 8 Hole choke body Gasket, XS# 48-1408 ..... $12.00/kit Float bowl Gasket 256, Float Valve assy. 2.0 Note: Carb Kits are produced by with washer, Pilot Jet #27.5 VM22/210 type, makers in Japan for a carb series #135 SmallRound Main Jet N102/221, Pilot (type) used in world markets and some components may differ from air Screw and spring, Washer for float bowl what has been originally installed main jet access plug and Choke plunger. in your XS/TX650. Some slide XS# 48-1920 ..... $16.00/kit Needles, Jets, and Mixture Screws may not match and in these cases CARB REBUILD KIT do not use these parts. Carb Rebuild Kit - Fits: XS650E/SE/F/ SF/2F (1978-79) Kit Contains: 8 Hole choke body Gasket, Float bowl Gasket 256, Float Valve assy. 2.0 with washer, Pilot Jet #27.5 VM22/210 type, #135 SmallRound Main Jet N102/221, Pilot air mixture Screw with O-Ring and spring, Washer for float bowl main jet access plug and Choke plunger. XS# 48-7879 ..... $19.00/kit CARB REBUILD KIT Carb Rebuild Kit - Fits: TX650A/XS650B (74-75) Kit Contains: Slide Needle Y-22 & clip, Pilot jet BS30/96 #42.5, Main Jet #130 Small round type N102/221, Float Needle & Seat assembly #2.5, Air screw with spring, 7 hole choke cover Gasket and Float bowl Gasket (256) XS# 48-1919 ..... $14.00/kit CARB REBUILD KIT CARB REBUILD KIT Carb Rebuild Kit - Fits:XS1/XS1B (1970-71) Kit Contains: Slide needle Y22 & clip, Pilot Jet BS30/96 #42.5, Main Jet - #130 Small round N102/221, Float Needle & Seat assembly #2.0, Air Screw with spring, Choke Plunger & spring, float bowl Gasket ( 256) XS# 48-1917 ..... $14.00/kit Carb Rebuild Kit - Fits:XS2/TX650 (1972-73) Kit Contains : Slide Needle Y22 & clip, Pilot Jet BS30/96 #42.5, Main Jet - #130 Small round N102/221, Float Needle & seat assembly #2.0, Air screw with spring, metal Washer (bowl plug) , and float bowl Gasket (256) XS# 48-1918 ..... $14.00/kit 58 CARB HOLDERS/POD FILTERS Fuel/Carb Section (C) Version 01 March/05 STOCK TYPE AIR FILTERS Note: Rejeting is usually required with Pods RUBBER JOINT - CARB to AIR FILTER BOX POD AIR FILTER Pod Air Filter - Oval, tapered K&N type with chrome end cap. Will fit behind stock XS/TX650 sidecovers. 52mm. ID (2.047") - Fits: 70-79 650's - stock 38mm. CV carbs XS# 15-0036 ..... $12.00each 54mm. ID (2.125") - Fits: 80-84 XS650 stock 34mm. CV carbs XS# 15-0035 ..... $12.00each 1pc. of Air box rubber Joint (ref.# 8) & 2pc.of Tension Spring- (Ref.# 9) Fits: 1970-84 XS/TX 650's - Carb to air box - right or left side. XS# 15-0671 ... $10.00/3pc.set CARB HOLDERS CARB HOLDERS Carb Holder Set - Fits:Stock BS38 CV Carbs on TX650A 74 & XS650B/C/D (75-77) - Kit Includes 1pc.(RH) #447-13565 & 1pc.(LH) #447-13555 Made in Japan by OEM maker XS# 48-1480 ...... $36.00/set Carb Holder Set - Fits:Stock BS34 CV Carbs on 80-84 XS650 + Mikuni aftermarket VM-34/36 & 38mm. roundslide carbs. Kit Includes 1pc. each of carb holders OEM # 3G1-13586 & OEM # 3G1-13596 XS# 20-6038 ..... $34.00/set Note: Carb holders are Not available for the 70-73 models. #48-1480 will fit the 70-73 models but there will be some additional pressure to get them to align with the air box as the early holders had a slightly different angle. BLIND PLUG Blind Plug - Carb Holder Air Barb XS# 48-1447 .... $1.50ea. 59 Fuel/Carb Section (C) Version 01 March/05 STOCK AIR FILTERS All 650's Require 2 Filters per bike and these fit into the stock Airbox Air Filter - Fits: XS650G-K - All 1980-84 650's OEM# 3G1-14451 XS# 15-0655 ... $22.00ea. Air Filter - Fits: XS650C/D/E/SE/F/SF/2F 1976-79 OEM# 533 -14451-00 XS# 15-0653 ... $22.00ea. Air Filter - Fits: XS1/XS1B 70-71 OEM# 256-14451 XS# 15-0651 ..... $12.00ea. Air Filter - Fits:XS2/TX650 72-73 OEM# 306-14451 XS# 15-0652 ..... $12.00ea. Air Filter - Fits: TX650A 1974, XS650B 1975 OEM# 447-14451-01 XS# 15-0654 ... $22.00ea. 60
Similar documents
chassis rubber mounts
Damper Rubber - ( rider footrest bracket ) - Set of 4 (Figure #20) - Fits: All 1970-84 XS/TX650's XS# 02-6527 ..... $16.00/set/4 See Pg 93 for Footrest Crown Nuts & Washers
More information