SpeedTouch™580 Installation and Setup Guide

SpeedTouch™580
Wireless Residential ADSL Gateway
Installation and Setup Guide
Release R4.3.2
SpeedTouch™
580
Installation and Setup Guide
R4.3.2
Copyright
Copyright ©1999-2005 THOMSON. All rights reserved.
Passing on, and copying of this document, use and communication of its contents is not permitted without written authorization
from THOMSON. The content of this document is furnished for informational use only, may be subject to change without notice,
and should not be construed as a commitment by THOMSON. THOMSON assumes no responsibility or liability for any errors or
inaccuracies that may appear in this document.
Thomson Telecom Belgium
Prins Boudewijnlaan, 47
B-2650 Edegem
Belgium
www.speedtouch.com
Trademarks
The following trademarks are used in this document:
SpeedTouch™ is a trademark of THOMSON.
UNIX® is a registered trademark of UNIX System Laboratories, Incorporated.
Adobe, the Adobe logo, Acrobat and Acrobat Reader are trademarks or registered trademarks of Adobe Systems, Incorporated, registered in the United States and/or other countries.
Netscape® and Netscape Navigator® are registered trademarks of Netscape Communications Corporation.
Microsoft®, MS-DOS®, Windows® and Windows NT® are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.
Apple® and Mac OS® are registered trademarks of Apple Computer, Incorporated, registered in the United States and
other countries.
Ethernet™ is a trademark of Xerox Corporation.
UPnP™ is a certification mark of the UPnP™ Implementers Corporation.
Wi-Fi® and the Wi-Fi logo are registered trademarks of the Wi-Fi Alliance. "Wi-Fi CERTIFIED", "Wi-Fi ZONE", "Wi-Fi Alliance", their respective logos and "Wi-Fi Protected Access" are trademarks of the Wi-Fi Alliance.
Other products may be trademarks or registered trademarks of their respective manufacturers.
Document Information
Status: v2.0 (July 2005)
Reference: E-DOC-CTC-20050429-0061
Short Title: Installation and Setup Guide ST580 R4.3.2 (en)
Contents
Contents
About this Installation and Setup Guide ................... 1
E-DOC-CTC-20050429-0061 v2.0
1
Introducing the SpeedTouch™.................................... 3
2
Basic Installation ........................................................... 5
2.1
Setting Up your SpeedTouch™ ...................................................... 6
2.2
First Time Installation .................................................................... 7
2.2.1
Guided Installation........................................................................................................... 8
2.2.2
Manual Installation ........................................................................................................ 17
2.3
The SpeedTouch™ Setup CD........................................................ 19
2.4
SpeedTouch™ Connections Essentials......................................... 21
2.5
Connections Overview and Powering .......................................... 22
2.5.1
Installing USB drivers.................................................................................................... 23
2.5.2
Wireless Setup ............................................................................................................... 25
2.6
Basic Security .............................................................................. 26
3
Web-Based User Interface.......................................... 29
i
Contents
ii
4
Internet Connection Troubleshooting....................... 31
4.1
Checking the Hardware................................................................ 32
4.2
LED Diagnostics ........................................................................... 33
4.3
Web Diagnostics .......................................................................... 35
4.4
SpeedTouch™ Setup CD Troubleshooting ................................... 37
4.5
Wireless Setup Troubleshooting .................................................. 40
4.6
Easy Setup Troubleshooting ........................................................ 41
E-DOC-CTC-20050429-0061 v2.0
About this Installation and Setup Guide
About this Installation and Setup Guide
Used symbols
A note provides additional information about a topic.
A tip provides an alternative method or shortcut to perform an action.
!
Terminology
Documentation and
software updates
A caution warns you about potential problems or specific precautions that
need to be taken.
Generally, the SpeedTouch™580(i) will be referred to as SpeedTouch™ in this
Installation and Setup Guide.
THOMSON continuously develops new solutions, but is also committed to improve
its existing products.
For suggestions regarding this document, please contact
documentation.speedtouch@thomson.net.
For more information on THOMSON's latest technological innovations, documents
and software releases, visit us at:
www.speedtouch.com
E-DOC-CTC-20050429-0061 v2.0
1
About this Installation and Setup Guide
2
E-DOC-CTC-20050429-0061 v2.0
Chapter 1
Introducing the SpeedTouch™
1 Introducing the SpeedTouch™
Introduction
In a minute you will be able to access the Internet using your
SpeedTouch™580(i) Residential ADSL Gateway.
This Installation and Setup Guide will show you how to set up your SpeedTouch™
and how to connect a computer or a local area network (LAN) to the Internet.
Identifying your
SpeedTouch™
The label on the bottom side of your SpeedTouch™, informs you on the
SpeedTouch™’s:
Product name
Model number
Serial number
Power requirements
!
DSL variants
Do not remove, nor cover the marking label.
The SpeedTouch™ comes in two ADSL flavours:
The ADSL POTS variant: The SpeedTouch™580 connects to an analogue Plain
Old Telephone Service (POTS) line.
The ADSL ISDN variant: The SpeedTouch™580i connects to an Integrated
Service Digital Network (ISDN) line, enabling residences with an ISDN line to
use the ADSL service.
You can easily identify your variant by checking the product name printed on the
label on the bottom of your SpeedTouch™.
!
E-DOC-CTC-20050429-0061 v2.0
Use only the SpeedTouch™ variant which is appropriate for the DSL service
provided to your premises.
3
Chapter 1
Introducing the SpeedTouch™
SpeedTouch™ Setup
CD
Your SpeedTouch™ is delivered with a Setup CD.
If you insert the CD on a Microsoft Windows PC or Mac OS X computer:
The first time, an intuitive SpeedTouch™ Quick Installation Wizard will guide
you through the hardware setup of your SpeedTouch™ and will help you to
connect to the Internet.
See “2.2 First Time Installation” on page 7 for more information.
For future reference, the SpeedTouch™ CD Menu provides links to all contents
See “2.3 The SpeedTouch™ Setup CD” on page 19 for more information.
In case of another operating system a set of subdirectories allows you to easily
browse for user documentation, SpeedTouch™ system software, service templates,
etcetera.
SpeedTouch™ Home
Install Wizard
The SpeedTouch™ Home Install Wizard has been designed to help you on the
Internet in a flash.
First, the wizard will try to detect your SpeedTouch™. After connecting your
computer, the wizard will configure your SpeedTouch™ and - if necessary - your
computer.
The Home Install Wizard was designed for Microsoft Windows operating systems
and Mac OS X - in the latter case provided you will use a wired connection to your
SpeedTouch™.
You can launch the SpeedTouch™ Home Install Wizard:
Automatically from out the SpeedTouch™ Quick Installation Wizard when you
insert the SpeedTouch™ Setup CD in a computer for the first time.
See “2.2 First Time Installation” on page 7 for more information.
From the SpeedTouch™ CD Menu Home page, via Run Quick Installation. This
will in fact re-run the Quick Installation Wizard and subsequently start the
Home Install Wizard as if you launch the Setup CD for the first time.
From the SpeedTouch™ CD Menu Maintenance page, via Reconfigure my
SpeedTouch™.
If you do not want to use the guided installation procedure, you can also
fully manual install and configure your SpeedTouch™. See “2.2.2 Manual
Installation” on page 17 for more information.
4
E-DOC-CTC-20050429-0061 v2.0
Chapter 2
Basic Installation
2 Basic Installation
Before you begin
ADSL service
Make sure to read the safety instructions and regulatory notices first. The safety
instructions can be found on the Setup CD (see “2.2 First Time Installation” on
page 7) and/or may also be provided as printed booklet.
The ADSL service must be up and running on your telephone or ISDN line.
If both telephone and ADSL service are simultaneously available from the same
copper pair, you will need a central splitter or distributed filters for decoupling
ADSL and telephone signals.
Public telephone lines carry voltages that can cause electric shock. Only try
to set up splitter/filters that have been designed to be installed by
unqualified personnel. For further assistance, contact your service provider.
!
Computer requirements
To connect computer(s) via Ethernet, make sure the computer(s) are equipped with
an Ethernet network interface card (NIC).
To connect a computer via USB, you need a free USB port on the computer or a
connected USB hub.
For wireless networking, you will need a wireless 802.11 b/g compatible client
adapter for each computer you intend to connect wirelessly.
As wireless client adapter, you can:
What you need from
your ISP
E-DOC-CTC-20050429-0061 v2.0
Use a provided SpeedTouch™110g CardBus.
Use a provided SpeedTouch™120g USB adapter (with cable).
Plug a provided SpeedTouch™121g adapter directly into your computer’s USB
port (without cable).
Use any other Wi-Fi certified WLAN client.
Following configuration parameters are provided by your ISP:
Your ISP’s connection service model (for example PPPoE)
VPI/VCI (for example 8/35)
Your user name and password to connect to the Internet
5
Chapter 2
Basic Installation
2.1 Setting Up your SpeedTouch™
SpeedTouch™ housing
Wall mount
The SpeedTouch™ can be mounted on a wall, setup upright or simply be placed as
a desktop.
You can mount the SpeedTouch™ on a wall or other vertical surface:
Proceed as follows:
1
Drill two holes in the wall or other vertical surface where you want to place the
SpeedTouch™.
2
Fasten two screws in the wall holes. The screws should protrude five
millimetres from the surface of the wall.
3
Attach your SpeedTouch™ on the wall using the two mounting slots on the
bottom side.
If you install the SpeedTouch™ onto plasterboard, use dowels to
secure the screws. Otherwise the strain of the cables connected to the
SpeedTouch™ rear panel connectors could pull the SpeedTouch™
from the wall.
Stand-up
6
To setup the SpeedTouch™ in an upright position, use the provided cradle (if
available).
E-DOC-CTC-20050429-0061 v2.0
Chapter 2
Basic Installation
2.2 First Time Installation
Internet connectivity
setup
There are different ways of setting up Internet connectivity on your SpeedTouch™.
The best way depends on your operating system.
If you use following
operating system
the recommended way to setup your
SpeedTouch™ is
MS Windows (98 SE,
Millennium, 2000 or XP)
the Home Install Wizard, as described in
“2.2.1 Guided Installation” on page 8.
Mac OS X, provided you will
use a wired connection to
your SpeedTouch™
Any operating system
(provided you have IP
connectivity)
Mac OS X, wirelessly
connected to your
SpeedTouch™ and provided
you have IP connectivity
the Easy Setup, as described in “2.2.2 Manual
Installation” on page 17: Open your web
browser, the SpeedTouch™ HTTP intercept will
do the rest.
If you are using MS Windows XP, it is also be possible to use the MS
Windows XP Internet Gateway Device (IGD) Control Agent for UPnP, as
described in the SpeedTouch™ User’s Guide.
E-DOC-CTC-20050429-0061 v2.0
7
Chapter 2
Basic Installation
2.2.1 Guided Installation
Introduction
On the CD a Quick Installation Wizard is provided that will guide you through the
first installation and set-up of your SpeedTouch™.
The Quick Installation Wizard will:
Provide important safety information and regulatory information.
Show you how to make the necessary connections to your SpeedTouch™.
How to turn on your device.
Prepare you to smoothly run the SpeedTouch™ Home Install Wizard.
The subsequent SpeedTouch™ Home Install Wizard will then prepare your
SpeedTouch™ and your local computer(s) for connecting to the Internet.
The Home Install Wizard will:
Guide you through connecting your computer(s) to your SpeedTouch™.
Prepare the SpeedTouch™ for connecting to the Internet.
To be able to run the applications on the Setup CD on an MS Windows 2000,
an MS Windows XP operating system, or Mac OS X computer, you need
administrative rights.
!
IMPORTANT NOTICE
Launching the CD for
the first time
Do not make any connections to your SpeedTouch™ until you are instructed to do
so by the SpeedTouch™ Quick Installation Wizard and/or the SpeedTouch™ Home
Install Wizard.
To launch the SpeedTouch™ Setup CD Menu:
1
Insert the Setup CD in your computer's CD-ROM or DVD-ROM drive.
On MS Windows: The CD should autostart.
If not, refer to ”The SpeedTouch™ CD does not start
automatically” on page 37.
On Mac OS X: Double-click Menu in the window with the content of the
CD.
2
In the Choose Language window, select the language of your choice and click
OK.
3
The procedure continues with the SpeedTouch™ Quick Installation Wizard.
Proceed with “ Quick Installation Wizard” on page 9.
8
E-DOC-CTC-20050429-0061 v2.0
Chapter 2
Basic Installation
Quick Installation
Wizard
Proceed as follows:
1
The SpeedTouch™ Quick Installation Wizard will guide you through the first
setup of your SpeedTouch™.
On the Welcome page, click Next to continue.
If you ran the CD on this computer before, the Quick Installation
Wizard is not shown; instead the CD menu pops up.
2
Select your SpeedTouch™ product from the list of supported devices.
To easily identify your SpeedTouch™ a product picture is shown. If
you are not sure what device you have, check the label on the bottom
side of your SpeedTouch™.
Click Next to continue.
E-DOC-CTC-20050429-0061 v2.0
9
Chapter 2
Basic Installation
3
The SpeedTouch™ Safety Instructions and Regulatory Notices will be
displayed. Scroll down to read all the instructions carefully. If you have
carefully read these Safety Instructions and Regulatory Notices, select I have
read and I fully understand the Safety Instructions and Regulatory
Information to confirm your reading and click Next.
Your SpeedTouch™ product is designed and tested to meet the latest
safety standards. However, to ensure safe use of this product, it is
important that the Safety Instructions and Regulatory Notices shown
and/or available in the Safety and Regulatory booklet are read, and
complied with carefully, before installing the SpeedTouch™ product.
!
4
Subsequent screens will guide you through the preliminary hardware setup of
your SpeedTouch™.
Carefully follow all the instructions. Click Next each time your are ready to
proceed.
5
As soon as all required preliminary connections to your SpeedTouch™ have
been made, and your SpeedTouch™ is turned on and initialized, the final steps
in the Quick Installation Wizard will:
Make sure that you have all information readily available to let the Home
Install Wizard configure your SpeedTouch™ to connect to the Internet.
See “ What you need from your ISP” on page 5for an overview of
information you must have readily available.
Start the SpeedTouch™ Home Install Wizard.
Click Setup my SpeedTouch to continue.
6
The procedure continues with the SpeedTouch™ Home Install Wizard.
Proceed with “ Home Install Wizard” on page 11.
10
E-DOC-CTC-20050429-0061 v2.0
Chapter 2
Basic Installation
Home Install Wizard
Proceed as follows:
1
The SpeedTouch™ Home Install Wizard will guide you through your local
network connections and prepare the SpeedTouch™ for Internet connectivity.
On the Welcome page, click Next to continue.
2
The Software License Agreement window appears.
You must accept before continuing. Click Yes to accept.
If you accepted this License Agreement in a previous configuration
setup, this window will not be shown.
3
The SpeedTouch™ Home Install Wizard will check your system and will invite
you to connect the SpeedTouch™ to your computer.
See “ SpeedTouch™ wiring” on page 21 for a comprehensive
overview of all SpeedTouch™ connections.
E-DOC-CTC-20050429-0061 v2.0
11
Chapter 2
Basic Installation
4
Make one of following connections:
Connect the yellow RJ-45 Ethernet cable to the yellow (indicated)
Ethernet port on your SpeedTouch™ and the other end to the computer’s
Ethernet port.
Connect the blue USB cable to the blue indicated USB port on your
SpeedTouch™ and the other end to the computer’s USB port.
In case of problems or for advanced information, see
“2.5.1 Installing USB drivers” on page 23.
For wireless networking, plug a wireless card or adapter in your
computer.
In case of problems or for advanced information, see
“2.5.2 Wireless Setup” on page 25.
5
Once the hardware is installed successfully and you are connected to the
SpeedTouch™, the procedure continues with configuring your Internet
connection.
If the wizard does not detect a connection, an error message will be
displayed. Refer to “ The wizard does not detect a connection” on
page 37.
Proceed with “ Configuring the Internet connection” on page 13.
12
E-DOC-CTC-20050429-0061 v2.0
Chapter 2
Basic Installation
Configuring the Internet
connection
Proceed as follows:
1
If prompted, enter the User name and Password for your SpeedTouch™
security settings and click OK.
The factory default user is ‘Administrator’. Its password is blank,
meaning you do not have to enter anything in the password field. It is
advisable to specify another user name and password to protect your
SpeedTouch™ from security violation during the configuration
procedure (see “2.6 Basic Security” on page 26 for more information.
2
Select the appropriate Region, Provider and Service for your Internet
connection as specified by your service provider and click Next.
!
3
4
If the service provider has included a separate disk with a dedicated
service profile, click Have Disk... to browse to the location of the
appropriate service profile template file.
From here on the procedure might differ from the description below.
The requested information will depend on the selected service profile
and should be provided by your Service Provider. Subsequent screens
will guide you through the configuration setup of both the
SpeedTouch™ and your computer. Enter the requested information
and click Next whenever requested.
First your Internet connectivity will be set up:
Select the VPI/VCI - and, if required, the Connection Type - as specified
by your service provider and click Next.
Enter the User Name and Password for your Internet account settings as
specified by your service provider and click Next.
The procedure continues with some additional configurations.
Proceed with “ Configuring the SpeedTouch™ (and your computer)” on
page 14.
E-DOC-CTC-20050429-0061 v2.0
13
Chapter 2
Basic Installation
Configuring the
SpeedTouch™ (and your
computer)
Proceed as follows:
1
Depending on the selected service profile and your ISP’s requirements,
additional settings may be requested to be filled in during the Home Install
Wizard, like Dynamic DNS Service, Time Configuration or other.
Enter the information provided by your ISP and click Next whenever
requested.
2
To protect your SpeedTouch™ from unauthorised access, you must provide a
user name and password. Each time a user wants to access a SpeedTouch™
management interface, the user will be prompted to provide this user name
and password before access is granted.
Click Next to continue.
3
To protect the wireless connections to your SpeedTouch™, move the slide
control to the desired security mode.
Following security modes to secure traffic between the SpeedTouch™ and
connected wireless stations are available:
14
Low, which implies in fact that no security measures are taken at all
Medium, implying that traffic is encrypted by means of a static
encryption key (WEP).
E-DOC-CTC-20050429-0061 v2.0
Chapter 2
Basic Installation
High, providing the highest security standard available (WPA) for
encrypting all wireless traffic.
For an overview on all SpeedTouch™ wireless security features, see
“ Securing your wireless network” on page 26.
4
The procedure continues with the final steps of configuring your
SpeedTouch™ and your computer.
Proceed with “ Finishing the Home Install Wizard” on page 16.
E-DOC-CTC-20050429-0061 v2.0
15
Chapter 2
Basic Installation
Finishing the Home
Install Wizard
Proceed as follows:
1
The SpeedTouch™ Home Install Wizard will configure the SpeedTouch™ and
your computer according to the service profile. You can follow the
configuration progress in following window:
2
Finally, click Finish to close the wizard.
After some seconds, the Internet LED on your SpeedTouch™ will be lit green to
indicate Internet connectivity. If not, refer to “4.2 LED Diagnostics” on page 33. If
needed, you can test your Internet connection as described in “ Testing your
Internet Connection” on page 35.
The SpeedTouch™ CD Menu will be displayed. See “2.3 The SpeedTouch™ Setup
CD” on page 19 for more information.
You will be redirected to the embedded SpeedTouch™ pages automatically (unless
you cleared the http://speedtouch.lan check box in the last window of the Home
Install Wizard). These pages allow you to configure your firewall, device settings,
your wireless access point settings, and so on. See the SpeedTouch™ User’s Guide
for more information.
More on IP settings
The computer’s networking interface, used during the Home Install Wizard
procedure, will be configured for obtaining its IP configuration dynamically in the
very most cases. This is the most convenient configuration and should not be
changed.
For fixed or advanced IP configurations, please follow the instructions of
your ISP.
16
E-DOC-CTC-20050429-0061 v2.0
Chapter 2
Basic Installation
2.2.2 Manual Installation
Web-Based Easy Setup
With help of the Easy Setup, your Internet connection is set up in a few clicks.
The Easy Setup is Operating System independent.
Preconditions
Make sure that:
Your SpeedTouch™ is correctly set up and powered on.
Your computer is connected to the SpeedTouch™. In case of a wireless
connection, a wireless client adapter has to be installed on your computer and
correctly configured to connect to your SpeedTouch™.
See “ SpeedTouch™ wiring” on page 21 for a comprehensive
overview of all SpeedTouch™ connections.
Your host computer is configured as DHCP client or is configured with a valid
fixed IP address.
in case of problems, you can give the host computer a fixed IP address
in the same subnet as your SpeedTouch™ (If the SpeedTouch™ is in
its default settings, that is an address between 192.168.1.1 and
192.168.1.253). In case you use fixed IP addresses, the SpeedTouch™
has to be configured as DNS server (default).
HTTP intercept
Your web browser is not using a proxy server. For more information, see
“ Disable proxy server” on page 41.
Proceed as follows:
1
Open a web browser. Browse to an arbitrary web site, for instance http://
www.speedtouch.com. As long as no Internet connection has been set up, you
will be automatically redirected to the SpeedTouch™ Welcome page.
If you’re not redirected automatically, go to “ Launching the Easy
Setup wizard” on page 18
E-DOC-CTC-20050429-0061 v2.0
2
Click on Setup my SpeedTouch to launch the Easy Setup wizard.
3
Proceed with “ Setting up Internet connection” on page 18.
17
Chapter 2
Basic Installation
Launching the Easy
Setup wizard
Setting up Internet
connection
It is always possible to launch the Easy Setup wizard from within the embedded
web pages. Proceed as follows:
1
Browse to the SpeedTouch™ pages on http://speedtouch.lan or on its IP
address, its default being 192.168.1.254.
2
In the menu click SpeedTouch.
3
In the Pick a task... list click Set Up.
In the Easy Setup wizard:
1
Click Next to proceed. If for some reason you want to abort the wizard, click
Cancel.
2
Choose the Service provided by your ISP (Router or Bridge); then click Next.
3
Select the appropriate VPI/VCI - and, if required, the Connection Type (PPPoE
or PPPoA) - provided by your ISP; then click Next.
4
For a Routed service, fill in the Internet Account settings (PPP user name and
password) provided by your ISP. Click Next.
5
Fill in the SpeedTouch™ Security user name and Password.
The factory default user is ‘Administrator’. Its password is blank,
meaning you do not need to enter anything in the password field. It is
advisable to specify another Administrator user name and password
to protect your SpeedTouch™ from security violation, as described in
“2.6 Basic Security” on page 26.
18
6
In the next screen you can review your settings, before to start the
configuration of your SpeedTouch™. If something is missing or incorrect, click
Back. To confirm the settings, click Start.
7
Please wait until the configuration has been done, and then click Finish. After a
while you will be returned automatically to the Welcome page. Click on the
bottom link to go to the SpeedTouch™ pages or select Don’t show this page to
access the Internet via your default home page.
E-DOC-CTC-20050429-0061 v2.0
Chapter 2
Basic Installation
2.3 The SpeedTouch™ Setup CD
Introduction
Your SpeedTouch™ is delivered with a Setup CD.
If you insert the CD on a Microsoft Windows PC or Mac OS X computer, an intuitive
CD Menu guides you through the features and contents of the Setup CD.
In case of another operating system a set of subdirectories allows you to easily
browse for user documentation, SpeedTouch™ system software, service templates,
etcetera.
SpeedTouch™ CD menu
The SpeedTouch™ CD menu will pop up automatically each time you insert the CD,
or after running the Quick Installation Wizard and subsequent Home Install Wizard:
Select:
E-DOC-CTC-20050429-0061 v2.0
Run Quick Installation to start the SpeedTouch™ Quick Installation Wizard.
SpeedTouch Maintenance to:
Reconfigure your SpeedTouch™ via the Home Install Wizard.
Upgrade the software version on your SpeedTouch™.
Check for SpeedTouch™ upgrades on the Internet.
19
Chapter 2
Basic Installation
Documentation and Help to:
Consult user documentation for your SpeedTouch™ DSL Gateway.
Consult user documentation for SpeedTouch™ networking products.
See more information on SpeedTouch™ products and solutions.
Visit the online support sections on www.speedtouch.com.
In case you experience problems when viewing the SpeedTouch™
documentation, see “ SpeedTouch™ documentation cannot be
viewed” on page 38.
20
Open a new window to view the Setup CD contents.
E-DOC-CTC-20050429-0061 v2.0
Chapter 2
Basic Installation
2.4 SpeedTouch™ Connections Essentials
SpeedTouch™ wiring
The figure below shows all possible types of connection to the SpeedTouch™.
15VAC
ON/OFF
1
2
3
4
The colour coded printing on the backpanel of your SpeedTouch™ will
facilitate matching the colour coded cables.
Making connections
In most cases, the SpeedTouch™ Quick Installation Wizard and Home Install Wizard
will guide you through the process of making all required connections to your
SpeedTouch™.
It is recommended to wait to make any of these connections until the wizard
will ask you to do so. See “2.2 First Time Installation” on page 7 for more
information.
In case you want to make the required connections yourself, see “2.5 Connections
Overview and Powering” on page 22 for more information.
E-DOC-CTC-20050429-0061 v2.0
21
Chapter 2
Basic Installation
2.5 Connections Overview and Powering
Introduction
In case you want to make the required connections yourself without using the
guided installation procedure as recommended, you must:
Make sure to read the safety instructions and regulatory notices first.
The safety instructions can be found on the Setup CD (see “2.2 First
Time Installation” on page 7) and/or may also be provided as printed
booklet.
DSL Connection
Powering the
SpeedTouch™
Follow the order as indicated below for making connections to your
SpeedTouch™.
Use the grey DSL cable to wire the SpeedTouch™ DSL port to your telephone wall
outlet or distributed filter.
Plug in the coaxial jack from the electric power supply adapter into the
SpeedTouch™ power inlet port and the other end to the wall outlet.
The SpeedTouch™ electrical power requirements are indicated on the label
on the bottom side of your SpeedTouch™. In case you need to use another
power supply than the one provided, make sure that the spare supply
complies with the SpeedTouch™ power requirements.
!
To power on the SpeedTouch™, press the power button on the SpeedTouch™ rear
panel.
During the start-up procedure, the power LED on the front panel is lit red for some
seconds. As soon as the power LED is solidly lit green, your SpeedTouch™ is ready
for service. After another couple of seconds, also the DSL LED will light green.
If these LEDs do not light, please refer to ”Checking the LEDs” on page 33. A
comprehensive LED overview can be found in the SpeedTouch™ User’s Guide.
To power off your SpeedTouch™, use the same button.
Network connections
Your SpeedTouch™ allows you to connect your computer(s) via:
Ethernet
USB
Wireless networking
It is recommended to use the Guided Installation procedure.
See “2.2.1 Guided Installation” on page 8 for more information.
22
E-DOC-CTC-20050429-0061 v2.0
Chapter 2
Basic Installation
2.5.1 Installing USB drivers
USB connection
Supported operating
systems
You may want to connect your computer to the SpeedTouch™ using the USB port.
To be able to do so, you must install the corresponding USB driver.
USB connectivity on the SpeedTouch™ is supported for:
Microsoft Operating Systems:
MS Windows 98SE
MS Windows Millennium
MS Windows 2000
MS Windows XP
You may need the Windows installation CD during installation.
The installation procedure might be slightly different depending on
the MS Windows OS you are using.
Installing Windows USB
drivers
Mac Operating Systems:
Mac OS X 10.2 (Jaguar)
Mac OS X 10.3 (Panther)
Mac OS X 10.4 (Tiger)
The first time you connect the SpeedTouch™ to your computer through the USB
port, as soon as you plug the USB cable into the computer, you will be prompted for
a USB driver.
You will find the required USB driver software on the Setup CD. The installation is
plug and play, meaning that installation will require almost no effort.
Proceed as follows:
1
Insert the blue USB cable provided into the SpeedTouch™ USB port marked
with the USB logo.
An USB logo looks like this:
2
The other end of the USB cable fits in (one of) the USB port(s) of your
computer. In most cases your computer's USB port is marked with the same
USB symbol.
You can also connect your computer to the SpeedTouch™ via a USB
hub, provided that the hub is autonomously powered.
3
E-DOC-CTC-20050429-0061 v2.0
Windows will automatically recognise the Thomson USB Remote NDIS
device:
23
Chapter 2
Basic Installation
4
The Windows Found New Hardware Wizard appears. This wizard will guide
you through the installation procedure of the USB drivers.
Click Next to continue.
The Windows Found New Hardware Wizard may ask your
authorisation to connect to Windows Update to search for software. If
this is the case, select No, not this time and click Next.
5
Make sure that the SpeedTouch™ Setup CD is inserted, then select Instal the
software automatically (Recommended), and click Next.
6
The USB driver is being installed. After a while a completing dialogue will
appear. Click Finish, to close the wizard.
Continue with ”Configuring the SpeedTouch™ (and your computer)” on page 14.
Installing Mac USB
drivers
You will find the required USB driver software on the Setup CD. The installation is
plug and play, meaning that installation will require almost no effort.
Proceed as follows:
1
Insert the blue USB cable provided into the SpeedTouch™ USB port marked
with the USB logo.
An USB logo looks like this:
2
The other end of the USB cable fits in (one of) the USB port(s) of your
computer. In most cases your computer's USB port is marked with the same
USB symbol.
You can also connect your computer to the SpeedTouch™ via a USB
hub, provided that the hub is autonomously powered.
3
Mac OS X will automatically recognise the detection of a new port.
4
Make sure the SpeedTouch™ Setup CD is inserted, then click OK.
5
In the Network window, click Apply Now.
Continue with ”Configuring the SpeedTouch™ (and your computer)” on page 14.
24
E-DOC-CTC-20050429-0061 v2.0
Chapter 2
Basic Installation
2.5.2 Wireless Setup
Wireless client
adapters
For a wireless connection to your Wi-Fi certified SpeedTouch™, you will need a
wireless 802.11 b/g compatible client adapter.
As wireless client adapter, you can plug in a provided SpeedTouch™110g CardBus,
a SpeedTouch™120g USB adapter (with cable), a SpeedTouch™121g adapter or any
other Wi-Fi certified WLAN client, or - if present in your computer - use the built-in
Wi-Fi certified WLAN adapter
To be able to install hardware on a MS Windows 2000 or a MS Windows XP
operating system, you need administrative rights on your computer.
Installing your wireless
client adapter
The Home Install Wizard will invite you to plug in the wireless client adapter.
Proceed as follows:
1
Plug in the wireless client adapter. The hardware is being installed.
If you use a SpeedTouch™wireless networking adapter, the
SpeedTouch™ Wireless Client Manager, an alternative to the Wireless
Zero Configuration (WZC) in Windows XP, will be installed. If you’re
working on Windows XP and prefer to work with the WZC, see
”Restoring Windows Zero Configuration” on page 40 to switch back to
WZC.
With the provided SpeedTouch™110g/120g/121g adapter, the client
manager will be configured correctly for secure WLAN connectivity to
the SpeedTouch™. Also for a third party WLAN client on MS Windows
XP with Service Pack 2, the WLAN configuration will be correctly done
via the WZC. In other cases you will need to configure the client
manager of your WLAN client without help of the wizard.
E-DOC-CTC-20050429-0061 v2.0
2
Enter your SpeedTouch™’s serial number. This 13 digit key is printed on the
bottom label of your SpeedTouch™. Then click Next.
3
In a progress window you can follow the setup of the wireless connection to
your SpeedTouch™.
4
Continue with ”Configuring the SpeedTouch™ (and your computer)” on
page 14.
25
Chapter 2
Basic Installation
2.6 Basic Security
Default user name and
password
Changing your
password
The SpeedTouch™ comes with a default user; its user name is ‘Administrator’ and
the default password is blank.
For security reasons, it is recommended to set a password to access the
SpeedTouch™.
1
Go to the SpeedTouch™ home page (http://speedtouch.lan or 192.168.1.254).
2
In the left pane select Toolbox > User Management.
3
In the Pick a task... list, click Change my password.
4
Enter a new password and confirm.
Do not forget this login information. In case you forget, you will be forced to
reset the SpeedTouch™ back to its default configuration.
Default wireless
security settings
Also for wireless connections to your SpeedTouch™, by default there are no
security settings, so the SpeedTouch™ is initially accessible to all wireless devices:
The Access Control List (ACL) is open and empty; new stations are
automatically allowed to access the SpeedTouch™.
The Network Name (SSID) is broadcasted.
The security level is initially set to Low (that is: no encryption is used).
It is recommended to change these SpeedTouch™ wireless access point settings
either automatically via the SpeedTouch™ Home Install Wizard, either manually as
described in the SpeedTouch™ User’s Guide.
Securing your wireless
network
To secure your wireless network, you can:
1
Allow or deny access based on the MAC address of the wireless client(s).
Known MAC addresses are kept in the Access Control List (ACL). If the
SpeedTouch™ is configured to allow new stations via registration, unknown
computers will have to register before they can connect.
For the ACL you have following options: New stations are:
26
Allowed (automatically): All new stations can access the
SpeedTouch™.
Allowed (via registration): Only allowed stations in the ACL have
access. You can add new stations via the Association /
Registration button.
Not allowed: Only allowed stations in the ACL have access.
2
Turn off the broadcast of the wireless Network Name (SSID). New wireless
clients that are scanning for available networks will not see your network
appear in their list.
3
Encrypt the data that will be sent over the wireless network. You can choose
different encryption methods or levels of security:
High: Wi-Fi Protected Access Pre-Shared Key (WPA-PSK) encryption, the
highest form of security available, but can only be used if your wireless
client and client manager support it
Medium: Wired-Equivalent Privacy (WEP) encryption
Low: no encryption, no security
E-DOC-CTC-20050429-0061 v2.0
Chapter 2
Basic Installation
For more information, see the SpeedTouch™ User’s Guide.
E-DOC-CTC-20050429-0061 v2.0
27
Chapter 2
Basic Installation
28
E-DOC-CTC-20050429-0061 v2.0
Chapter 3
Web-Based User Interface
3 Web-Based User Interface
Embedded pages
Access
The SpeedTouch™ comes with embedded web pages, providing an interface to the
software installed on the device. It allows easy setup and management of the
SpeedTouch™ via your web browser from any PC connected to the SpeedTouch™.
To access the pages:
1
Open your web browser.
The recommended screen resolution is 1024 by 768 pixels.
2
In the address bar type http://speedtouch.lan or your SpeedTouch™’s IP
address, by default that is 192.168.1.254, and press Enter.
3
Enter your SpeedTouch™ security user name and password.
The default user name is Administrator and the default password is
blank.
4
Tasks
Using the web pages
The SpeedTouch™’s home page will be displayed in your browser window.
From here - depending on the rights of your user account - you have access to
the other pages.
Amongst others you can:
View the SpeedTouch™’s current settings and status.
Configure the SpeedTouch™ to connect to your Service Provider with the
settings provided.
Set the SpeedTouch™’s firewall to work with specific applications.
Set up security features.
Enable remote management access.
Back up your configuration settings.
Reset the SpeedTouch™’s default settings.
Update the SpeedTouch™’s software.
When making changes to the SpeedTouch™ configuration via the web pages, the
configuration is stored automatically whenever you click the Apply button.
For more information on the embedded pages, go to the Help link in the upper right
side of the notification and navigation area or refer to the SpeedTouch™ User’s
Guide.
E-DOC-CTC-20050429-0061 v2.0
29
Chapter 3
Web-Based User Interface
Site Map
The following Site Map gives you an overview of the main pages:
SpeedTouch
Information
Configuration
Event Logs
Update
Broadband Connection
DSL Connection
Internet Services
Toolbox
Remote Assistance
Game & Application Sharing
Parental Control
Firewall
Intrusion Detection
Dynamic DNS
User Management
Home Network
Devices
Interfaces
30
E-DOC-CTC-20050429-0061 v2.0
Chapter 4
Internet Connection Troubleshooting
4 Internet Connection Troubleshooting
What to check
The first things to check if you cannot access the Internet, are:
Power
Hardware connections
LEDs
If the suggestions in this chapter do not resolve the Internet connection problem,
please contact your Service Provider.
For other problems (Wireless, Security, Management,....), refer to the SpeedTouch™
User’s Guide.
E-DOC-CTC-20050429-0061 v2.0
31
Chapter 4
Internet Connection Troubleshooting
4.1 Checking the Hardware
Check the wiring
Plug in properly all cables you need. Ensure that the cables between your
SpeedTouch™, computers and telephone socket are plugged in firmly. Loose
connections can affect your Internet connection.
Damaged cables can interfere with your Internet connection. Check for damage
along the cables and loose connections at the end of the cable. Replace any
damaged cables.
Test the telephone line
To eliminate the possibility of a fault with the telephone line itself, check for a dialtone by using a telephone connected to the telephone master socket.
If you are using ADSL, check whether a splitter has been installed or that microfilters have been correctly fitted.
If there is no dial tone, contact your telephone company.
Reboot your computer
Power-cycle the
SpeedTouch™
32
Loss of Internet or network connectivity can be caused by the computer. Often a
reboot will rectify the problem.
To reboot your SpeedTouch™, simply turn off your SpeedTouch™. Wait five
seconds and turn it back on.
E-DOC-CTC-20050429-0061 v2.0
Chapter 4
Internet Connection Troubleshooting
4.2 LED Diagnostics
Checking the LEDs
After establishing Internet connectivity, at least following LEDs should solidly light
green: Power, DSL, Internet.
LED status
Possible solutions
No LEDs are lit
The SpeedTouch™ is not powered, or turned of.
Power LED is lit
red or flashing
amber
DSL LED is
flashing green or
no DSL LED
No Ethernet LED
No Ethernet port’s
Link Integrity/
Activity LED
E-DOC-CTC-20050429-0061 v2.0
Make sure the SpeedTouch™ is plugged into an
electrical outlet.
Make sure you are using the correct power supply for
your SpeedTouch™ device. The SpeedTouch™
electrical power requirements are indicated on the
label on the bottom side of your SpeedTouch™.
Make the SpeedTouch™ is powered on.
Unplug the SpeedTouch™, reboot your computer and
then plug the SpeedTouch™ back in.
The SpeedTouch™ is malfunctioning or not able to start
up.
Fully unplug the SpeedTouch™ from any computer
and disconnect it from its power supply. Wait five
seconds, connect the SpeedTouch™ again and turn it
back on.
Run the SpeedTouch™ Upgrade Wizard, available
from the CD Menu to restore the system software.
Your DSL service is unable to synchronise.
Ensure the SpeedTouch™ is plugged into the DSLenabled phone line.
Ensure micro-filters have been correctly fitted (if not,
there is a big chance you also have a bad regular
telephone service).
Make sure that the correct SpeedTouch™ variant
(ISDN or POTS) according the DSL/phone service
provided to your premises.
If you have previously had a working connection, call
your ISP to check for service outages.
No Ethernet connectivity:
Make sure the Ethernet cable(s) are firmly connected
to the 10/100Base-T port.
Make sure you are using the correct cable type for
your Ethernet equipment.
Make sure the Ethernet NIC driver is correctly
installed and enabled on your computer. Power safe
options for the Ethernet NIC should preferably be
disabled.
33
Chapter 4
Internet Connection Troubleshooting
LED status
Possible solutions
No USB LED
No USB connectivity:
WLAN LED is
flashing or not lit
Make sure the USB cable is firmly connected to the
USB port.
Make sure the USB driver is correctly installed and
enabled on your computer.
The WLAN LED flashes if there is wireless LAN
activity and can have different colours:
Green: The SpeedTouch™ wireless access point
is operating in highest security mode (WPA).
Make sure to use the same WPA encryption on
the WLAN client.
Amber: The SpeedTouch™ wireless access
point is operating in medium security mode
(WEP). Make sure to use the same WEP
encryption on the WLAN client.
Red: The SpeedTouch™ wireless access point
uses no security.
The WLAN LED is not lit if the SpeedTouch™ wireless
access point is disabled. For wireless networking,
ensure the WLAN is enabled on the SpeedTouch™:
1
Go to the SpeedTouch™ web pages.
2
In the menu select Home Network > Interfaces.
3
Click the WLAN.
4
Click Configure.
5
Select Interface Enabled.
- OR Press and hold the Association / Registration button
until the WLAN LED is lit (green, amber or red).
The WLAN LED is toggling between red and green: If
new stations are only allowed via registration and if
you pressed the Association / Registration button, the
ACL will be unlocked for 30 seconds during which
you can connect new wireless clients.
Red Internet LED
or No Internet LED
There was an authentication failure. This will usually
present itself as an error message regarding an
incorrect password.
Check that your user name is correct. For ADSL
connections, the user name is normally in the
form of username@ISP.
Check that your password is correctly entered.
The password is case sensitive.
If you continue to get password failures, contact your
ISP.
The wrong service profile was selected. Restart the
setup of your SpeedTouch™, and make sure to select
the correct service profile.
A comprehensive LED overview can be found in the SpeedTouch™ User’s Guide.
34
E-DOC-CTC-20050429-0061 v2.0
Chapter 4
Internet Connection Troubleshooting
4.3 Web Diagnostics
Testing your Internet
Connection
After setting up the Internet connection, there is a simple way to check whether
your configuration is fine.
1
Go to the SpeedTouch™ home page (http://speedtouch.lan or 192.168.1.254).
2
On the left navigation pane, select SpeedTouch.
3
In the Pick a task... list, click Check connectivity to the Internet.
4
Select an Internet Service to Check.
5
Click Check Connectivity.
6
If the test is successful, you will get a list of green check marks as in the
example below:
In case of problems, see “ Connectivity check” on page 36.
E-DOC-CTC-20050429-0061 v2.0
35
Chapter 4
Internet Connection Troubleshooting
Connectivity check
How to do a simple connectivity check on the web pages, is described in “ Testing
your Internet Connection” on page 35.
If the test is successful, you will get a list of green check marks in the test results.
Otherwise a red cross will help you to diagnose the problem.
Test result
Explanation
Your DSL line is not synchronised.
Check if your telephone line is correctly
connected to your SpeedTouch™.
Check the DSL LED, as described in “ Checking
the LEDs” on page 33.
No ATM activity detected on your DSL line.
No Ethernet activity.
In case you are connected through a protocol other
than PPPoE, this check is not applicable; the result
will always be ‘No Ethernet activity’.
36
Authentication failed: check your user name
and password. The user name is in most cases
in the form of username@ISP.
Your connection is disconnected.
Could not bring up link.
No IP
No IP address or no DNS server has been
configured. During IP address negotiation, there
was an IPCP error or a DHCP error.
No Internet
This test sends 1 ping to each address of a
configured list of IP addresses. The test succeeds if
all addresses can be reached. If your primary and
secondary DNS server are part of the list, reaching
one of both is enough.
No DNS
If this step fails, it may be because the DNS service
provided by your ISP has a problem.
E-DOC-CTC-20050429-0061 v2.0
Chapter 4
Internet Connection Troubleshooting
4.4 SpeedTouch™ Setup CD Troubleshooting
The SpeedTouch™ CD
does not start
automatically
In MS Windows:
1
In the Windows task bar, click the Start button.
2
Select Run...
3
In the Open field, enter the following path: D:\Setup.exe, where D stands for
the drive letter of your CD-ROM drive.
In Mac OS X:
The wizard does not
detect a connection
1
On your desktop double-click the CD icon.
2
Double-click Menu.
If the Home Install Wizard does not detect a connection to your SpeedTouch™, an
error window appears.
In this case check that:
The SpeedTouch™ is turned on and fully initialised.
Your computer has a valid IP address, that is any address but 0.0.0.0.
In MS Windows:
1
In the task bar, click the Start button.
2
Select Run...
3
Type cmd in the Open field.
4
Click OK. A black window will appear with a flashing cursor.
5
Type ipconfig /all and then press Enter.
In MS Windows 98 or MS Windows Millennium, type winipcfg and
then press Enter.
6
E-DOC-CTC-20050429-0061 v2.0
Your IP address is displayed.
37
Chapter 4
Internet Connection Troubleshooting
In Mac OS X:
1
Go to Dock > System References.
2
Click Network.
3
On the TCP/IP tab, your IP address is displayed.
No dedicated firewall device or router is placed between your computer and
the SpeedTouch™.
No personal firewall software is running on your computer.
Your computer is correctly connected to the SpeedTouch™, or check whether
the WLAN client is correctly associated with the SpeedTouch™.
1
In the Windows XP notification area, click the Wireless Network
Connection icon
.
If you’re not connected, this icon will have a red cross:
2
Check whether the displayed network has your SpeedTouch™ network
name (SSID).
To repeat the search for your SpeedTouch™, click Back or restart the wizard. As
soon as the wizard finds your SpeedTouch™, you can continue with “ Configuring
the SpeedTouch™ (and your computer)” on page 14.
The SpeedTouch™ is
not responding
If the completing window does not appear after running the SpeedTouch™ Home
Install Wizard, this means that the SpeedTouch™ is not responding or not
accessible anymore.
There are two possibilities:
This might be due to the reconfiguration of the SpeedTouch™’s IP settings or
wireless access point settings. In this case, the last window of the Home Install
Wizard will not be shown. Your SpeedTouch™ is correctly set up though and
you will be able to surf the Internet.
If you did not reconfigure the SpeedTouch™’s IP settings or wireless access
point settings, restart the Home Install Wizard.
If the setup fails over a wireless connection, try - if possible - to setup
your SpeedTouch™ using a wired connection.
If the problem persists, refer to the Service Provider’s instructions for more
information.
SpeedTouch™
documentation cannot
be viewed
To be able to view the SpeedTouch™ documentation pages on the Setup CD,
Javascript must be enabled in your web browser. For more information, see the
help file of your web browser.
To allow active content on an MS Windows XP system, see “ Active content in
Internet Explorer” on page 39.
38
E-DOC-CTC-20050429-0061 v2.0
Chapter 4
Internet Connection Troubleshooting
Active content in
Internet Explorer
When opening documentation pages from the Setup CD a warning might be
displayed; this is for instance the case if the pages are opened in Internet Explorer
and you are using MS Windows XP with Service Pack 2.
To be able to view the documentation, proceed as follows:
1
In Internet Explorer following message will appear in the Information Bar:
2
Click the Information Bar (with the warning).
3
Select Allow Blocked Content.
4
A security warning will be displayed:
5
Click Yes.
Now you can view or print the SpeedTouch™ documentation pages.
This warning will be displayed every time you consult the documentation. If
you do not want this message to be shown in the future, you must allow
CDs to run active content on your computer:
E-DOC-CTC-20050429-0061 v2.0
1
In the Internet Explorer menu select Tools > Internet Options.
2
Under Security select Allow active content from CDs to run on My
Computer.
39
Chapter 4
Internet Connection Troubleshooting
4.5 Wireless Setup Troubleshooting
Restoring Windows
Zero Configuration
When installing a SpeedTouch™110g/120g/121g, the SpeedTouch™ Client Manager
will be installed. The SpeedTouch™ Client Manager is an alternative to the
Windows Zero Configuration (WZC) in Windows XP. In many cases the
SpeedTouch™ Client Manager will disable the WZC.
You need administrative privileges on your computer to restore the WZC
service.
For information about starting the WZC service, visit the Microsoft knowledge base
on http://support.microsoft.com.
Uninstalling the
SpeedTouch™ Wireless
Client Manager
Every time you reconnect to a WLAN the SpeedTouch™ Wireless Client Manager
will start itself up again though, forcing the WZC to go down.
Therefore, you might want to uninstall the SpeedTouch™ Wireless Client Manager.
Proceed as follows:
40
1
In the Windows XP task bar, click the Start button
2
Select (All) Programs > SpeedTouch 110g/120g/121g Wireless Monitor >
Uninstall SpeedTouch 110g/120g/121g Wireless Monitor.
3
The Uninstall wizard will start running. Click OK to confirm you want to
uninstall.
4
The Install Shield Wizard will appear and will notify the SpeedTouch ST110g/
120g/121g Monitor is successfully uninstalled. Click Finish to close the wizard.
5
After uninstalling the SpeedTouch™ Wireless Client Manager, you can restore
the WZC.
E-DOC-CTC-20050429-0061 v2.0
Chapter 4
Internet Connection Troubleshooting
4.6 Easy Setup Troubleshooting
Prerequisites
Before to run the Easy Setup on the embedded SpeedTouch™ pages, check
following:
The necessary connections are made.
The SpeedTouch™ is powered on.
Your host computer is configured as DHCP client or is configured with a valid
fixed IP address.
In case of problems, you can give the host computer a fixed IP address
in the same subnet as your SpeedTouch™ (If the SpeedTouch™ is in
its default settings, that is an address between 192.168.1.1 and
192.168.1.253).
In case you use fixed IP addresses, the SpeedTouch™ has to be
configured as DNS server (default).
Supported web
browsers
Disable proxy server
Your web browser must be able to run Javascript. Following browsers are
supported:
Internet Explorer (5.0 and later)
Netscape Navigator (4.7 and later)
Mozilla Firefox (1.2 and later)
Opera (5 and later)
Safari (1.0 and later)
Konqueror (2.2 and later)
The Easy Setup will only work if the proxy server is disabled or if the proxy server is
bypassed for local addresses. For more information, see the help file of your web
browser.
To disable a proxy server in Internet Explorer:
1
In Internet Explorer, select Tools > Internet Options from the menu.
2
Select the Connections tab.
3
Click the Lan settings... button.
4
Clear the Use proxy server box and the Use automatic script box.
It is recommended first to disable all other network connections on your
computer, except the one connecting to your SpeedTouch™.
!
To disable a network connection:
E-DOC-CTC-20050429-0061 v2.0
1
In the Windows XP task bar, click the Start button
2
Select (All) Programs > Control Panel > (Network and Internet
Connections >) Network Connections.
3
Right-click on the network interface icon you want to disable and
choose Disable.
41
Chapter 4
Internet Connection Troubleshooting
42
E-DOC-CTC-20050429-0061 v2.0
© THOMSON 2005. All rights reserved.
E-DOC-CTC-20050429-0061 v2.0
.
Need more help?
Additional help is available online at www.speedtouch.com