E77 Installation Guide(EN) - ICT - International Currency Technologies

E77
Bill Acceptor
Installation Guide
2007 International Currency Technologies Corporation
V. 3.0 Part Number : H4913B-R
International Currency Technologies Corp.
Contents
1. Introduction ......................................................................... 2
1-1. Overview ...................................................................... 2
1-2. Features ...................................................................... 2
2. Specifications ..................................................................... 2
General ............................................................................... 2
Electrical ............................................................................. 3
Use of Materials Limitations
International Currency Technologies Corporation (ICT) all rights reserved.
All materials contained are the copyrighted property of ICT.
All trademarks, service marks, and trade names are proprietary to ICT.
ICT reserves the right at all times to disclose or to modify any information as
ICT deems necessary to satisfy any applicable law, regulation, legal process
or governmental request, or to edit, refuse to post or to remove any information
or materials, in whole or in part, in ICT's sole discretion.
Mechanical ......................................................................... 3
3. Packing List ........................................................................ 3
4. Dimension .......................................................................... 4
5. Installation .......................................................................... 6
5-1. PIN Assignment ............................................................6
5-1-1. I/O Circuit ............................................................. 7
5-2. DIP Switch Setting ....................................................... 8
5-3. Software Download and Upgrade .............................. 8
6. Maintenance ....................................................................... 9
7. Troubleshooting ................................................................... 10
1
www.ictgroup.com.tw
E77 Bill Acceptor
Bill Acceptor E77
1. Introduction
1-1. Overview
E77 features a high currency verification and recognition with
new verification unit which including auto calibration and antistringing function with multiple interfaces to provide users the
best service.
Installation: Indoor use only!!
Electrical
1-2. Features
Fixed-width/ Multi-width bill acceptable.
Multi-currencies acceptable.
Anti-stringing technologies.
Auto calibration available.
Durable construction design.
High transaction speed.
Multiple interfaces available.
Easy maintenance.
Power Consumption
12V- Standby : 0.35A, 4.2 W
Operation: 2.3 A, 27.6W
Maximum: 4 A, 48 W
Power Source
12V DC (11.4~12.6V DC)
Operation Environment
Operation Temperature: 0°C~55°C
Storage Temperature: -20°C~70°C
Humidity: 30%~85RH
(no condensation)
Mechanical
Outline Dimension
Refer to page. 4
Weight
Approx. 1.2kg
2. Specifications
General
Acceptance Rate
96% or greater
Note: The incomplete bills such as extremely dirty, wet, broken or
wrinkled ones are excluded.
Bill Insertion
Four way acceptance
Transaction Speed
Approx. 2 seconds to stack
Interface
Parallel
Bill Accepted Width
Approx. 77mm
www.ictgroup.com.tw
2
3. Packing List
Main
Bill Acceptor
Accessory
E77 Installation Guide
E77 DIP Switch Setting Guide
3
www.ictgroup.com.tw
E77 Bill Acceptor
Bill Acceptor E77
4. Dimension
Figure 1
To install the bill acceptor on your VMC, please be aware of the
dimension as below:
[ L ] : Longer than the maximum length of accepted bills.
[ L1 ] : Bill box capacity depth.
* [ L/2 ] has to be longer than 70mm to open upper base.
L/2
Figure 2
90.00[3.54]
78.00[3.07]
72.00[2.83]
65.00[2.56]
L
85.00[3.35]
95.28[3.75]
L
61.50[2.42]
87.00[3.43]
99.20[3.91]
128.70[5.07]
L1
64.53[2.54]
52.90[2.08]
87.00[3.43]
86.00[3.39]
Unit : :mm[in]
www.ictgroup.com.tw
4
5
www.ictgroup.com.tw
E77 Bill Acceptor
Bill Acceptor E77
5. Installation
5-1. PIN Assignment
Figure 3
5-1-1. I/O Circuit
Parallel Interface.
Figure 4
(CN1)
+5VDC~+12VDC
4K7
CN1
POWER+12V
VEND1
VEND2
VEND3
ABN
STKF
1
3
5
7
9
11
13
15
17
19
21
23
25
A 1
A 2
A 3
A 4
A 5
A 6
A 7
A 8
A 9
A10
A11
A12
A13
B 1
B 2
B 3
B 4
B 5
B 6
B 7
B 8
B 9
B10
B11
B12
B13
POWER GND
2
4
6
8
10
12
14
16
18
20
22
24
26
INHIB
ACK
REJ
Customer Side
+5VDC
10K
10K
REJ
ACK
INHIB
E-REJ
E-ACK
E-INHIB
Hi"TR ON
Lo"TR OFF
PRES
TR
Bill Acceptor
25
1
26
2
6
E-VEND1~3
E-STKF
E-PRES
E-ABN
Bill Acceptor
13X2
www.ictgroup.com.tw
VEND1~3
STKF
PRES
10K
ABN
7
Customer Side
www.ictgroup.com.tw
E77 Bill Acceptor
Bill Acceptor E77
6. Maintenance
5-2. DIP Switch Setting
There is one serial DIP switches which are located on the side
of E77(as Figure 5). According to different currencies and credit
output format which are used by users, DIP switch settings could
be varied to fit users' need.
Please refer to “E77 Series DIP Switch Setting” Guide in the
package for more details.
Foreign objects on the LED or sensor may cause bill jamming and
decrease acceptance rate. To make sure the bill acceptor always
works smoothly, please clean the internal parts regularly.
To clean the internal parts:
1. Turn Bill Acceptor off.
2. Push the buttons on both sides of bill path and open the unit.
3. Use a soft, dry cloth or towel to clean the bill path and sensors.
Figure 5
Buttons
Sensor
Figure 7
5-3. Software Download and Upgrade
To download and upgrade the software to E77, the programmer
(FP-001) is needed. Please contact ICT to purchase FP-001 and
refer to FP-001 user guide for software download and upgrade
information.
Sensor
Figure 6
COM2
PH
5 4
9 8
Firmware
3
2
1
7 6
Maintenance Notice
(Any improper maintenance will result invalid warranty.)
Firmware
PC
E77
WEL-R7U03
FP-001
WEL-R087
Alcohol
Recommended
Mild, non-abrasive, soap water.
DO NOT USE
Organic solvent , Alcohol, Volatility liquid.
Please turn on Bill Acceptor after connecting..
www.ictgroup.com.tw
8
9
www.ictgroup.com.tw
E77 Bill Acceptor
7. Troubleshooting
Figure 8
LED
Taiwan
International Currency Technologies Corporation
Ji-Hong Building, No 24, Alley 38, Lane 91, Nei-hu Rd., Sec. 1, Taipei, Taiwan, R.O.C.
Table 1
LED
Flashes
Status
Corrective Actions
1
Bill jammed.
Open bill path and then remove the
jammed bill.
2
Inhibit
Inspect for right DIP switch setting.
3
Sensor error.
Inspect for foreign objects on sensor or
bill path and clean.
4
A stringing attempt
has detected.
Inspect for foreign objects on sensor or
bill path and clean.
7
Motor error.
Inspect for foreign objects on bill path
and clean.
If the error can not be solved after corrective actions or
happen again, please contact ICT for technical support.
www.ictgroup.com.tw
10
Tel: 886-2-2797-1238 ‧ Fax: 886-2-2797-1634
sales@ictgroup.com.tw (For Sales)
rma@ictgroup.com.tw (For Customer Service)
Website: www.ictgroup.com.tw