998 SPARE PARTS MANUAL ENGLISH ISSUE 7.pub

Transcription

McHale Engineering Limited
998 SQUARE BALE WRAPPER
SPARE PARTS MANUAL
ISSUE 7
McHale Engineering Limited,
Ballinrobe,
County Mayo,
Ireland.
Tel. +353 94 9520300.
Fax. +353 94 9520356
Email: sales@mchale.net
Website: www.mchale.net
Issue 7
McHale 998 Square Bale Wrapper
Page 1
998 SQUARE BALE WRAPPER
SPARE PARTS MANUAL
ISSUE 7
Page 2
Issue 7
Introduction
The McHale 998 square bale wrapper which you have purchased has
been developed through years of constant research and development. Given
proper care and attention the 998 will give years of reliable and dependable
performance. However it is important that the operators manual is read and fully
understood to achieve this, before the machine is operated. As part of this
philosophy it is vital to use only genuine McHale replacement parts, as these
are manufactured to the same standard as the original machine. These may be
obtained through your McHale dealer.
If any part of this manual is not fully understood please contact your
McHale dealer who will be able to answer any questions you may have. It is
important to quote the machine serial number when requiring spare parts or
technical assistance. Space is provided below to record machine details
Serial number:
Year of manufacture:
Date of delivery:
If you require further copies of this parts manual
please quote part number: CLT00071
Due to a policy of continuous product development and improvement, McHale Engineering Ltd
reserve the right to alter machine specification without prior notice.
Issue 7
Page 3
Contents
Title
Page
Abbreviations
5
Chassis
6
Stub axle/wheel
10
Arch
12
Dispenser reduction
14
Dispenser drive
16
Dispenser
18
Cut & hold backplate
20
Cut & hold slider
22
Unloading roller
24
Cradle arm
26
Roller cradle
30
Drawbar
32
Headstock
34
PTO shaft
36
Hydraulic tank
38
Main conveyor rear drive
40
Bale position sensor arms
44
Front conveyor
46
Spare film holder
50
Hydraulic control valve
52
Roller rotation block
54
Dispenser drive block
56
Steel hydraulic pipes
58
Electronic components 1
60
Electronic components 2
62
Lighting
64
Decals
66
Options
69
Note:
Parts described as left and right are done so according to direction the machine
normally travels in. For example the drawbar side of the machine is the left hand
side.
Page 4
Issue 7
Abbreviations
A/R
NLS (1)
U90001
F90001
Issue 7
As required
No longer supplied, refer to item 1
Used up and including to serial number 90001
Used from and including serial number 90001
Page 5
Page 6
Issue 7
CHASSIS
No. PART NUMBER
1
ACH00001
2
CMH00249
3
CFA00017
4
CMH00329
5
CFA00289
6
CFA00138
7
CFA00124
8
CZD02079
CZD02100
9
CFA00123
10
CFA00126
11
CFA00132
12
CFA00052
13
CZD02035
14
CFA00290
15
CMH00247
16
CMH00246
17
CFA00243
ACH00037
18
CCH00014
CCH02008
CCH02012
19
CZC02001
CZC02017
CFA00031
21
ACH00038
22
CRA00082
CSE00084
CRA00088
CRA00089
23
CFA00010
24
CMH00276
25
CMH00071
26
CBE00002
27
CVA03010
28
ACH00051
29
CFA00024
30
CFA00137
31
ACH00042
32
CFA00118
33
CMH00287
Issue 7
DESCRIPTION
QUANTITY
CHASSIS
1
BOTTOM RUNNER STRIP (WOOD)
2
SETSCREW, M10x30 CUP SQUARE Z/P
6
CHAIN GUIDE (WOOD)
2
BOLT, M12x130 CUP SQUARE Z/P
4
WASHER, 12mm FLAT
7
NUT, M12 NYLOC
8
CONVEYOR BOTTOM RUNNER LIP RIGHT
1
CONVEYOR BOTTOM RUNNER LIP LEFT
1
NUT, M10 NYLOC
204
NUT, M14 NYLOC
10
NUT, M8 NYLOC
8
SETSCREW, M8x20 Z/P
8
FRONT LIGHT BRACKET
2
SETSCREW, M10x30 CSK HEX
10
SHORT WEAR STRIP (PLASTIC)
2
LONG WEAR STRIP (PLASTIC)
2
SETSCREW, M10x20 BUTTON HEAD
188
MAIN CONV. CHAIN COMPLETE (9,17,18,19)
1
MAIN CONV. SINGLE CHAIN C/W JOINER
2
JOINER LINK
2
INNER LINK (ATTACHMENT)
A/R
CONVEYOR SLAT
(F90001)
47
CONVEYOR SLAT
(U9809)
47
SETSCREW, M12x25 Z/P
6
HYDRAULIC HOSE TRAY
1
CONVEYOR LIFT CYLINDER COMPLETE
1
LIFT CYLINDER SEAL KIT
1
LIFT CYLINDER ROD
1
LIFT CYLINDER GLAND
1
ROLL PIN, 8x50 Z/P
11
LIFT CYLINDER REAR PIVOT PIN
2
DRAWBAR CYLINDER REAR PIVOT PIN
1
RUBBER BUFFER
2
HYDRAULIC ACCUMULATOR, 30 BAR
1
REAR LIGHT BRACKET
2
16
WASHER, 10mm SPRING
8
CRADLE PIVOT PIN
4
GREASE NIPPLE, M8 STRAIGHT
4
SLOTTED LINK TOP PIN
2
Page 7
Page 8
Issue 7
CHASSIS
No. PART NUMBER
34
CHY00020
35
CHY02008
36
CHY00053
37
CVA03011
38
CFA00305
39
ACH00039
40
CZB02018
41
CFA00023
42
CZF02133
43
ACH00040
45
CFA00251
46
CFA00292
47
CZB02017
48
CFA00033
49
CFA00250
50
CFA00207
51
ADB00011
52
CMH00259
53
CZF02105
54
CFA00027
55
CHY02013
56
CZD02102
57
CMH00030
CMH00070
ACH00053
CTP00046
CTP00047
Issue 7
DESCRIPTION
QUANTITY
WASHER, 3/8" "DOWTY"
(U90054)
2
ADAPTER, 3/8"-1/2"
(U90054)
2
4
HYDRAULIC ACCUMULATOR, 70 BAR
2
NUT, M20 PLAIN Z/P
4
MAIN CONVEYOR ADJUSTER BOLT
2
HYDRAULIC VALVES INNER COVER
1
9
INSPECTION COVER
1
HYDRAULIC VALVES REAR COVER
1
WASHER, 10mm SKM
16
SETSCREW, M8x10 SOCKET CAP
16
HYDRAULIC VALVES OUTER COVER
1
SETSCREW M12x35 Z/P
1
WASHER, 12mm SKM
1
WASHER, 12mm SPRING
1
DRAWBAR MAIN PIVOT PIN CAP
1
DRAWBAR MAIN PIVOT PIN
1
WASHER, 12x85x6
1
BOLT M10x60 Z/P
1
ADAPTER, 1/2"-1/2"
(F90055)
2
CHAIN RUNNER
(F249995)
2
BOTTOM BALE LIFT CYLINDER PIN
4
MAIN CONVEYOR REAR DRIVE HINGE PIN
2
CHAIN DOWN CLAMP
(U90055)
4
WHEEL CHOCK
(F250172)
2
WHEEL CHOCK BRACKET
(F250172)
2
Page 9
Page 10
Issue 7
STUB AXLE/WHEEL
QUANTITIES ARE PER SIDE
No. PART NUMBER
CAX00012
CAX00013
1
CRA00100
2
CFA00127
3
CAX00018
4
CFA00008
5
CFA00129
6
CFA00302
7
CAX00019
8
ACH00047
ACH00048
9
CFA00236
10
CAX00020
CWH00007
CWH00013
11
CWH00014
12
CWH00016
13
CFA00121
14
CAX00022
CAX00023
15
CAX00024
CAX00025
16
CSE00004
CSE00007
Issue 7
DESCRIPTION
STUB AXLE, COMPLETE (HYD + AIR) LEFT
STUB AXLE, COMPLETE (HYD + AIR) RIGHT
BRAKE OPERATING CYLINDER (HYD)
BOLT M10x60 Z/P
BRAKE OPERATING LEVER
NUT M10 PLAIN
NUT M20 NYLOC
BRAKE SHOES (SET) (FAD)
BEARING KIT (2 BEARINGS & SEAL) ADR
BEARING KIT (2 BEARINGS & SEAL) FAD
WHEEL STUD
HUB (BRAKED)
WHEEL COMPLETE (16/70-20)
WHEEL COMPLETE (15/70-18)
WHEEL CENTRE (14x20)
TYRE (16/70-20)
WHEEL NUT
HUB NUT (ADR)
HUB NUT (FAD)
HUB CAP (ADR)
HUB CAP (FAD)
HUB SEAL (ADR)
HUB SEAL (FAD)
QUANTITY
1
1
1
1
1
1
6
6
1
1
1
6
1
1
1
1
1
6
1
1
1
1
1
1
Page 11
Page 12
Issue 7
ARCH
No. PART NUMBER
1
ACH00044
2
CZF02133
3
CFA00023
4
CFA00137
5
CFA00151
6
CFA00128
7
ACH00240
8
CFA00302
9
CFA00329
10
CMH00107
11
ATR00018
12
CFA00102
13
CFA00132
14
CZF02631
15
CFA00316
16
CFA00249
17
CFA00381
18
CFA00292
19
CFA00249
20
CFA00251
21
CHY02107
Issue 7
DESCRIPTION
ARCH
INSPECTION COVER
WASHER, 10MM SPRING
NUT, M16 NYLOC
TOP ARM
SETSCREW M20x50 Z/P
WASHER M20 SPRING Z/P
DOWEL Z/P
TOP REDUCTION GUIDE
SETSCREW M8x25 Z/P
NUT M8 NYLOC
SENSOR PLATE
BOLT M8x30 Z/P
WASHER SKM8
BOLT M20 X 50 Z/P
M8 X 10 SOCKET HEAD BOLT
WASHER SKM8
WASHER SKM10
STEEL HYDRAULIC PIPE ASSEMBLY
QUANTITY
1
1
4
4
16
16
1
4
6
4
1
2
2
1
2
2
6
2
2
2
1
Page 13
McHale HS2000 Round Bale Wrapper
Page 14
Issue 3
Issue 7
DISPENSER REDUCTION
No.
1
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
35
PART NUMBER
ADP00070
CXB00181
ADP00046
CFA00314
ADP00089
CMH00415
CFA00426
CFA00028
CZF02356
CZF02331
CGD00028
CSG00021
CZH00128
CFA00209
CEL00017
ADP00057
CFA00250
CFA00297
CBC00005
CPL00028
CFA00251
CFA00293
CFA00099
CFA00145
CFA00131
CFA00383
CFA00123
CEL00038
CFA00320
CFA00321
CZB02050
CFA00447
CFA00128
Issue 7
DESCRIPTION
DISPENSER CENTRE ARM
DISPENSER SIDE ARM
DISPENSER SAFETY LATCH
SETSCREW M5x40 Z/P
SAFETY ARM BRACKET
BUSH 12x30x42 NYLON
SHOULDER SCREW M10x70 Z/P
BOLT M10x65 Z/P
SAFETY ARM SECURING PLATE
SAFETY ARM BRACKET
DISPENSER SAFETY ARM
SAFETY ARM RETURN SPRING
WASHER 10MM
BOLT M16x120 Z/P
MAGNET BLUE WHEEL
DISPENSER ARM BACK BRACKET
WASHER SKM12
BOLT M12x40 Z/P
PLASTIC CAP
SAFETY BAR INSULATION
WASHER SKM10
SETSCREW M10x20 Z/P
SETSCREW M6x40 Z/P
WASHER MUDWING M6 32MMOD
NUT M6 NYLOC
BOLT M10x70 Z/P
NUT M10 NYLOC
SAFETY ARM SWITCH
WASHER FLAT 5MM
NUT M5 NYLOC
LOOM COVER
SETSCREW M8x10 BUTTON HD Z/P
NUT M16 NYLOC
QUANTITY
1
2
2
4
2
2
2
2
2
2
2
2
4
4
2
2
12
12
2
2
2
2
2
4
4
4
6
2
4
4
1
2
4
Page 15
Page 16
Issue 7
DISPENSER DRIVE
Note: 1. For machines with serial no.’s ranging from 250235 to 250160 use part
number ADP00097 when ordering a replacement motor or valve block (this kit replaces both motor and valve block as motor CMT00005 is no longer available).
2. For machines with serial no.’s ranging from 250159 and below, kit ADP00118 is
required.
Issue 7
Page 17
Page 18
Issue 7
DISPENSER
QUANTITIES SHOWN ARE PER UNIT. 2 UNITS PER MACHINE
No. PART NUMBER
ADP00086
1
CDG00001
2
CFA00185
3
CFA00102
4
CFA00124
5
CFA00139
6
CMH00056
6
CMH00057
7
CMH00096
7
CMH00174
8
CFA00052
9
CBR00004
10
CFA00153
11
CFA00132
12
CZD00114
13
CMH00034
14
CMH00035
15
CFA00024
16
CFA00137
17
CZD00118
18
CMH00619
18
CMH00661
19
ADP00040
20
CSG00031
21
CSG00010
22
CMH00197
22
CFA00208
23
CFA00010
24
CBR00068
25
CFA00135
26
CSG00009
27
CZC00112
28
CBR00009
29
CMH00087
30
CFA00001
31
CFA00032
32
CSG00013
33
CZH02165
34
CBC00012
35
CFA00242
36
ADP00051
Issue 7
DESCRIPTION
DISPENSER ASSEMBLY COMPLETE
GUARD DISPENSER GEARS
WASHER SPRING 8MM Z/P
SETSCREW M8x25 Z/P
NUT M12 NYLOC
WASHER FLAT 12MM HD Z/P
GEAR SPUR 1.5M 59T DISPENSER 64%
SETSCREW M8x20 Z/P
BEARING SLFL20
KEY 6x6x15
NUT M8 NYLOC Z/P
DISPENSER SPACER
ROLLER DISPENSER PRIMARY
ROLLER DISPENSER SECONDARY
SETSCREW M10x25 Z/P
WASHER SPRING 10MM HD Z/P
CUT AND TIE SPACER
PIN 30x280 STEPPED Z/P (750mm FILM)
PIN 30x535 STEPPED Z/P (500mm FILM)
DISPENSER FILM HOLDER ASSEMBLY
SPRING TOR. 6.35WDx480Dx7.8 COIL
SPRING COMP 1.625x16x40x8
PIN 16x84 STEPPED Z/P
GRUBSCREW M6x6 Z/P
ROLL PIN 8x50 Z/P
BEARING 30x34x16 STEPPED PLAS
WASHER FLAT 1” Z/P
SPRING COMP 2.95x37x197x12
DISPENSER SPACER
BEARING 6205 2RS
COIL ROLLER (2 BEARING TYPE)
CIRCLIP 25MM EXTERNAL Z/P
SETSCREW M12x30 Z/P
SPRING EXT. 1.83x12x65x14.5
DISPENSER HANDLE PART
CAP PLASTIC HANDGRIP 7/8”
CABLE ROLLER RELEASE 1095
DISPENSER MAIN FRAME
QUANTITY
1
1
2
2
3
2
1
1
1
1
8
4
2
8
2
1
1
1
1
1
1
1
2
1
1
1
1
2
1
1
1
4
2
2
1
1
1
1
1
1
Page 19
Page 20
Issue 7
CUT & HOLD BACKPLATE
QUANTITIES ARE PER UNIT, 2 UNITS PER MACHINE
No. PART NUMBER
ACT00001
1
CFA00124
2
CFA00139
3
CZD02055
4
CMH00262
5
CMH00261
6
CBR00020
7
CFA00270
8
CFA00272
9
CFA00269
10
CFA00268
11
CZC02012
12
CBE00002
13
CZD00118
14
CSG00004
15
CKN00011
16
CZF02121
17
CFA00144
18
CFA00098
19
ACT00003
20
CFA00118
21
CFA00032
22
CBR00016
23
CMH00023
24
CFA00137
25
CFA00024
26
CFA00031
27
CFA00131
28
CZH02119
Issue 7
DESCRIPTION
CUT & HOLD COMPLETE
NUT, M12 NYLOC
WASHER, 12MM FLAT (H/D)
BACKPLATE
ECCENTRIC BEARING HOLDER
CONCENTRIC BEARING HOLDER
BEARING, 6204 2RS
BOLT, M12x50 Z/P
SETSCREW M6x10 Z/P
WASHER, 6MM SHAKEPROOF
KNIFE CLAMP
BUFFER, RUBBER
WASHER, 10x40x4
SPRING, PLUNGER
KNIFE
KNIFE PLATE
WASHER, 6MM FLAT
SETSCREW, M6x25 Z/P
PLUNGER BRACKET
BUSH, "OILITE"
PLUNGER, CHROME
WASHER, 10MM SPRING
NUT, M6 NYLOC
WASHER 12X40X10
QUANTITY
9
6
1
1
2
3
1
2
2
2
1
1
2
1
2
1
4
2
1
1
4
1
1
1
1
4
2
2
Page 21
Page 22
Issue 7
CUT & HOLD SLIDER
QUANTITIES ARE PER UNIT. 2 UNITS PER MACHINE
No. PART NUMBER
1
ACT00002
ACT00010
2
CMH00260
3
CFA00089
CFA00362
4
CFA00126
5
CMH00330
6
CMH00331
7
CFA00012
8
CRA00074
CSE00074
CRA00103
CRA00104
CRA00105
CRA00106
CRA00101
CRA00102
9
CFA00132
10
CFA00147
Issue 7
DESCRIPTION
QUANTITY
SLIDER BARE (ALUM RAIL TYPE)
(F90050)
1
SLIDER (STEEL RAIL)
(U90049)
1
RAIL (ALUMINIUM)
(F90050)
1
SETSCREW, M8x45 CSK HEX Z/P
(F90055)
5
SETSCREW, M8x40 CSK HEX SS
(U90054)
5
NUT, M14 NYLOC
2
WASHER, RAM, DISHED
4
WASHER, RAM, RUBBER
2
NUT, 1 1/4" UNF NYLOC
1
CUT & HOLD CYLINDER COMPLETE
1
SEAL KIT, CUT & HOLD CYLINDER
1
CYLINDER ROD (TOP)
1
CYLINDER ROD (BOTTOM)
1
CYLINDER GLAND (TOP)
1
CYLINDER GLAND (BOTTOM)
1
CYLINDER PISTON (TOP)
1
CYLINDER PISTON (BOTTOM)
1
NUT, M8 NYLOC
(F90055)
5
WASHER, 8MM FLAT
(F90055)
5
Page 23
Page 24
Issue 7
UNLOADING ROLLER
No. PART NUMBER
1
ART00003
2
CFA00306
3
CFA00222
4
CFA00126
5
CBR00005
Issue 7
DESCRIPTION
UNLOADING ROLLER
WASHER, 14MM FLAT
NUT, M14 NYLOC
BEARING, 1 3/4" PILLOW BLOCK
QUANTITY
1
4
4
4
2
Page 25
Page 26
Issue 7
CRADLE ARM
QUANTITIES ARE PER MACHINE
No. PART NUMBER DESCRIPTION
1
CFA00111
2
CRA00087
LIFT CYLINDER COMPLETE (80mm BORE)
SLAVE
CSE00087
SEAL KIT (80mm BORE)
CRA00094
CYLINDER ROD (80mm BORE)
CRA00095
CYLINDER GLAND (80mm BORE)
CRA00093
CYLINDER PISTON (80mm BORE)
CRA00086
LIFT CYLINDER COMPLETE (90mm BORE)
MASTER
CSE00086
SEAL KIT (90mm BORE)
CRA00097
CYLINDER ROD (90mm BORE)
CRA00098
CYLINDER GLAND (90mm BORE)
CRA00096
CYLINDER PISTON (90mm BORE)
3
CBR00039
BUSH, GLACIER 2525
4
CBR00007
BUSH, GLACIER 3025
5
ARC00006
CRADLE ARM, RIGHT
ARC00007
CRADLE ARM, LEFT
6
CFA00124
NUT, M12 NYLOC
7
CFA00138
WASHER, 12mm FLAT
11
CFA00010
ROLL PIN, 8x50 Z/P
12
CMH0276
PIN, TOP RAM PIVOT
13
CFA00125
NUT, M12 PLAIN Z/P
14
CFA00324
15
CFA00032
16
CBR00031
BEARING, 35mm INSERT
17
CMH00245
BEARING RETAINER
18
CFA00232
CIRCLIP
19
CMT00007
ROLLER DRIVE MOTOR
20
CMH00285
SPROCKET, 3/4" PITCH 9 TOOTH
21
CFA00359
KEY, 8x7x30
22
CFA00149
WASHER, 8mm MUDWING
23
CFA00185
WASHER, 8mm SPRING
24
CFA00102
SETSCREW, M8x25 Z/P
25
CZF02003
MOTOR PLATE
26
CFA00033
SETSCREW M12x35 Z/P
Issue 7
QUANTITY
8
2
2
2
2
2
2
2
2
2
2
16
8
1
1
12
8
4
4
2
2
8
4
4
4
2
2
2
2
2
2
2
4
Page 27
Page 28
Issue 7
CRADLE ARM
No. PART NUMBER
27
CFA00023
28
CFA00137
29
CCH00007
CCH02002
CCH02003
30
CGD00015
31
CFA00249
32
CFA00101
Issue 7
DESCRIPTION
WASHER, 10mm SPRING
CHAIN, 3/4" C/W JOINER LINK
JOINER LINK
OFFSET LINK
CHAIN GUARD
WASHER, 8mm SKM
SETSCREW, M8x16 Z/P
QUANTITY
2
2
2
2
A/R
2
4
4
Page 29
Page 30
Issue 7
ROLLER
No. PART NUMBER
1
CFA00230
2
CFA00137
3
CZD00121
4
CFA00239
5
CMH00225
5
CMH00437
6
ARC00001
ARC00002
7
CMH00243
8
CBR00031
9
CMH00245
10
CFA00232
11
CZF02004
11
ARC00047
12
CFA00023
13
CMH00227
13
CMH00612
14
CGD00014
14
CGD00030
15
CFA00249
16
CFA00052
17
ARC00003
CPL00023
18
ARC00004
ARC00005
19
CMH00230
20
CFA00010
21
CZD02095
CZD02101
22
CFA00123
23
CZD02001
24
CBR00029
25
CFA00017
26
CCH00008
27
CCH02002
CCH02003
26
CCH02023
27
CCH02021
CCH02022
Issue 7
DESCRIPTION
QUANTITY
12
WASHER, 10mm SPRING
8
WASHER, 10x40x4
8
KEY, 10x8x40
8
SPROCKET, 3/4" PITCH 26 TOOTH (U250194)
6
SPROCKET, 3/4” PITCH 22 TOOTH (F250194)
6
ROLLER CRADLE, RIGHT
1
ROLLER CRADLE, LEFT
1
CRADLE PIVOT SHAFT
2
35mm BEARING INSERT
8
RETAINER RING
8
CIRCLIP
8
ADJUSTMENT CAM (U250194)
4
ADJUSTMENT CAM (F250194)
4
4
SPROCKET, 3/4” PITCH 15/15 T (U250194)
2
SPROCKET, 3/4” PITCH 13/13 T (F250194)
2
CHAIN GUARD (U250194)
2
CHAIN GUARD (F250194)
2
WASHER, 8MM SKM
4
SETSCREW, M8x20 Z/P
4
ROLLER (STEEL)
4
ROLLER (PLASTIC)
4
SLOTTED LINK, RIGHT
1
SLOTTED LINK, LEFT
1
SLOTTED LINK BOTTOM PIN
2
ROLL PIN, 8x50 Z/P
2
POTENTIOMETER GUARD, RIGHT
1
POTENTIOMETER GUARD, LEFT
1
NUT, M10 NYLOC
14
SUPPORT PLATE
4
BEARING, 35MM 3 BOLT STEEL
4
SETSCREW, M10x30 CUPHEAD Z/P
12
CHAIN, 3/4" PITCH C/W JOINER LINK (U250194
4
JOINER LINK 3/4" (U250194)
4
OFFSET LINK 3/4" (U250194)
A/R
CHAIN 3/4” PITCH 41 LINK 60H (F250194)
4
CHAIN LINK CONN. 3/4” ANSI 60H (F250194)
4
CHAIN LINK OFFSET 3/4” ANSI 60H (F250194)
A/R
Page 31
Page 32
Issue 7
DRAWBAR
No. PART NUMBER
1
CFA00202
2
ADB00012
3
CFA00135
4
CFA00010
5
CMH00071
6
ADB00009
7
ADB00010
8
CBR00039
9
CFA00111
10
CVA00040
11
CRA00079
CSE00073
CRA00099
CRA00092
CRA00090
12
ADB00007
13
CBR00019
14
CFA00062
15
ADB00008
16
CFA00027
17
CFA00123
Issue 7
DESCRIPTION
LINCH PIN, SMALL
DRAWBAR SAFETY BAR
WASHER, 1" FLAT
ROLL PIN, 8x50 Z/P
PIN, RAM PIVOT
STAND PIVOT PIN
STAND LOCKING PIN
BUSH,GLACIER 2525
GREASE NIPPLE M10 STRAIGHT
DRAWBAR CYLINDER VALVE
DRAWBAR CYLINDER COMPLETE
SEAL KIT
CYLINDER ROD
CYLINDER GLAND
CYLINDER PISTON
DRAWBAR BEAM
BUSH, GLACIER 6060
GREASE NIPPLE, M8 90
STAND
BOLT, M10X60 Z/P
NUT, M10 NYLOC
QUANTITY
2
1
2
2
1
1
1
4
2
1
1
1
1
1
1
1
4
2
1
1
1
Page 33
Page 34
Issue 7
HEADSTOCK
No. PART NUMBER
1
CFA00031
2
CFA00207
3
CZF02104
4
CMH00067
5
ADB00004
6
CFA00138
7
CFA00032
8
CFA00132
9
CFA00052
10
CZD02050
11
CFA00226
12
CFA00275
13
CMT00011
14
CMT00012
15
CZF02105
16
CFA00033
17
CMT00009
18
CZF02062
19
CFA00065
20
CZF02106
21
CBR00018
22
CMH00025
23
ADB00005
24
CFA00005
25
ADB00006
26
CFA00118
Issue 7
DESCRIPTION
WASHER, 12MM SPRING
PIVOT PIN TOP CAP
PIVOT PIN (SHORT)
HEADSTOCK BARE
WASHER, 12MM FLAT
NUT, M8 NYLOC
SETSCREW, M8x20 Z/P
HOSE HOLDER
BOLT, M8x100 Z/P
SETSCREW, M14x35 FLANGED Z/P
HYDRAULIC PUMP
GEARBOX
WASHER 12x85x6
PTO COVER
PTO COVER RING
WASHER 12x55x6
BUSH, GLACIER 4040
CAT. 2 LOWER LINK PIN
HITCH BAR
LINCH PIN, LARGE
HORIZONTAL PIVOT PIN
QUANTITY
4
10
1
1
1
4
2
4
2
1
2
2
1
1
1
2
1
1
2
1
2
2
1
2
1
1
Page 35
REAR (998)
4
1
5
6
7
8
2
9
10
6
3
5
FRONT (TRACTOR)
Page 36
Issue 7
PTO SHAFT
AGDRIVE
No. PART NUMBER
CMT00008
1
CMT00020
2
CMT00019
3
CMT00021
4
CMT00024
5
CMT00025
CMT00026
6
CMT00027
7
CMT00028
8
CMT00029
9
CMT00030
10
CMT00031
Issue 7
DESCRIPTION
PTO SHAFT COMPLETE
PLASTIC BEARING RING, LARGE INSIDE
COVER COMPLETE
PLASTIC BEARING RING, SMALL INSIDE
QUICK RELEASE BUTTON KIT
OUTER YOKE (6 SPLINE)
OUTER YOKE (21 SPLINE) OPTION
UNIVERSAL JOINT
INNER YOKE, LARGE PROFILE TUBE
LARGE PROFILE TUBE
SMALL PROFILE TUBE
INNER YOKE, SMALL PROFILE TUBE
QUANTITY
1
1
1
1
2
2
1
2
1
1
1
1
Page 37
Page 38
Issue 7
HYDRAULIC TANK
No. PART NUMBER
1
CFA00024
2
CFA00137
3
CHY00029
CHY00030
CHY00045
4
CPL00029
5
CHY00028
6
ADB00002
7
CHY00027
8
CHY02012
9
CHY02011
10
CFA00128
11
CFA00140
12
CFA00229
13
CSE00006
14
CHY00031
15
ADB00003
ADB00015
16
CFA00267
#
CHY00058
#
CHY00059
#
CMH00328
#
CHY00061
#
CHY00060
#
CFA00207
#
CFA00033
DESCRIPTION
WASHER, 10MM SPRING
RETURN FILTER COMPLETE
RETURN FILTER ELEMENT
RETURN FILTER CARTRIDGE ('98)
INTERNAL RETURN PIPE
FILLER CAP
HYDRAULIC TANK BARE
OIL LEVEL GAUGE
DRAIN BUNG
NUT, M16 NYLOC
WASHER, 16MM FLAT
OUTLET PLATE GASKET
SUCTION STRAINER
OUTLET PLATE, FLAT
OUTLET PLATE, STEPPED
SETSCREW, M6x25 Z/P
SUCTION PIPE 50mm
PIPE CLIP
PUMP SUCTION FLANGE
O RING
FLANGE CLAMP
WASHER, 12mm SPRING
QUANTITY
3
3
1
1
1
1
1
1
1
1
1
3
3
3
1
1
1
1
6
1
2
1
1
1
4
4
# = SUCTION PIPE ASSEMBLY FOR PUMP
Issue 7
Page 39
Page 40
Issue 7
MAIN CONVEYOR REAR DRIVE
No. PART NUMBER
1
CFA00230
2
CFA00137
3
CZD00121
4
CMH00320
5
ACN00001
6
CFA00312
7
CBR00033
8
CFA00123
9
CFA00358
10
CFA00247
11
CFA00142
12
CMH00231
13
CMH00311
14
CMH00226
15
CFA00263
16
CFA00229
17
CZF02052
18
CFA00128
19
CMH00317
20
CFA00252
21
CFA00325
22
ACN00002
23
CFA00118
24
CMT00006
25
CFA00124
26
ACN00003
27
CFA00356
28
CMH00177
29
CFA00360
30
CFA00361
31
CFA00251
32
CFA00310
33
CCH00009
CCH00001
CCH00004
34
CGD00013
35
CFA00132
36
CZF02219
37
ACN00013
Issue 7
DESCRIPTION
QUANTITY
2
WASHER, 10mm SPRING
2
WASHER, 10x50x4
2
ROLLER BUSH (PLASTIC)
4
ROLLER
2
16
BEARING, 40MM 4 BOLT STEP FLANGE
4
NUT, M10 NYLOC
16
KEY, 10x8x70
2
SETSCREW, M16x40 SOCKET CAP
4
4
WASHER, 16mm SPRING
SPROCKET, 75mm PITCH 7 TOOTH
2
MAIN CONVEYOR REAR SHAFT
1
SPROCKET, 1" PITCH 20 TOOTH
(U90055)
NLS (41)
KEY, 10x8x55
1
SETSCREW M16x35 Z/P
6
SIDEPLATE, RIGHT
(U90055)
1
NUT, M16 NYLOC
6
CHAIN ADJUSTER (PLASTIC)
1
WASHER, 16mm SKM
1
1
FRAME
(U90055)
1
2
CONVEYOR DRIVE MOTOR
1
NUT, M12 NYLOC
4
SIDEPLATE, LEFT
(U90055)
1
BOLT, M12x50 Z/P
4
1
SPLITPIN
1
MOTOR NUT
1
WASHER, 10mm SKM
1
BOLT, M10x50 Z/P
1
CHAIN, 1" C/W JOINER LINK 39 LINK (F249995)
1
JOINER LINK
A/R
OFFSET LINK
A/R
CHAIN GUARD
(U90055)
1
NUT, M8 NYLOC
2
SIDEPLATE, RIGHT
(F249995)
1
SIDEPLATE,LEFT
(F249995)
1
Page 41
Page 42
Issue 7
MAIN CONVEYOR REAR DRIVE
No. PART NUMBER
38
ACN00014
39
CCH00025
40
CGD00016
41
CMH00089
Issue 7
DESCRIPTION
QUANTITY
FRAME
(F249995)
1
CHAIN, 1" C/W JOINER LINK 41 LINK (U90055)
1
CHAIN GUARD
(F249995)
1
(F249995)
1
Page 43
Page 44
Issue 7
BALE POSITION SENSOR ARMS
No. PART NUMBER
4
CFA00010
7
CSG00011
11
CFA00137
14
ACH00054
ACH00055
15
CMH00105
16
CFA00230
17
CZD00121
18
CFA00359
19
CMH00106
20
CMH00073
Issue 7
DESCRIPTION
ROLL PIN, 8x50 Z/P
TENSION SPRING
WASHER, 10MM SPRING
SENSOR ARM, RIGHT
SENSOR ARM, LEFT
ROLLER
WASHER, 10x40x4
KEY, 8x7x30
PLASTIC BUSH
BALE SENSOR ARM SHAFT
(F249995)
(F249995)
(F249995)
(F249995)
(F249995)
(F249995)
(F249995)
(F249995)
QUANTITY
2
2
4
1
1
2
2
2
2
2
1
Page 45
Page 46
Issue 7
FRONT CONVEYOR
No. PART NUMBER
1
CFA00128
2
ACN00004
ACN00005
3
CFA00039
4
CFA00200
5
CFA00151
6
CFA00142
7
CMH00231
8
ACN00006
ACN00007
9
CFA00032
10
CFA00207
11
ACN00008
12
CFA00123
13
CBR00033
14
CFA00312
15
CFA00125
16
CFA00027
17
CCH00013
CCH02006
CCH02007
18
CMH00309
19
CFA00263
20
CZD00121
21
CFA00137
22
CFA00230
23
CMH00314
24
CFA00252
25
CFA00325
26
CFA00251
27
CFA00284
28
CZD02091
29
CFA00138
30
CFA00124
31
CFA00358
32
CMH00313
33
CFA00246
34
CFA00329
35
CZF02169
36
ACN00009
Issue 7
DESCRIPTION
QUANTITY
NUT, M16 NYLOC
8
BALE GUIDE, RIGHT
1
BALE GUIDE, LEFT
1
"U" BOLT, 80x80
2
"U" BOLT, 80x50
2
4
WASHER, 16mm SPRING
4
2
CONVEYOR, BARE
1
CONVEYOR, COMPLETE
1
9
WASHER, 12mm SPRING
9
LATCH CLOSER
2
NUT, M10 NYLOC
16
BEARING, 40mm 4 BOLT STEP FLANGE
5
8
NUT, M12 PLAIN Z/P
2
BOLT, M10x60 Z/P
4
CHAIN, 1" DUPLEX & JOINER LINK (U90055)
1
1" DUPLEX JOINER LINK
(U90055)
A/R
1" DUPLEX OFFSET LINK
(U90055)
A/R
SPROCKET, 1" DUPLEX 20 TOOTH
NLS (61)
KEY, 10x8x55
2
WASHER, 10x50x4
4
WASHER, 10mm SPRING
12
12
CHAIN ADJUSTER DUPLEX (PLASTIC)
1
WASHER, 16mm SKM
1
SETSCREW M16x25 Z/P
1
WASHER, 10mm SKM
1
BOLT, M10x90 Z/P
1
CHAIN GUARD
1
WASHER, 12mm FLAT
3
NUT, M12 NYLOC
17
KEY, 10x8x70
2
MAIN CONVEYOR FRONT SHAFT
1
SETSCREW, M20x40 FINE
(U249998)
2
WASHER, 20mm SPRING
(U249998)
2
WASHER, 20x50x6
(U249998)
2
SIDEPLATE, LEFT
(U249998)
1
Page 47
Page 48
Issue 7
FRONT CONVEYOR
No. PART NUMBER
37
CCH00012
CCH02005
CCH00017
CCH02014
CCH02013
38
ACN00011
39
CMH00069
40
CFA00010
41
CFA00139
42
CFA00078
43
CFA00080
44
ACN00010
45
CMH00308
46
CFA00129
47
CMH00316
48
CMH00234
49
CBR00032
50
CMH00315
51
CMH00248
52
CFA00062
53
ACN00012
54
CFA00201
55
CFA00126
56
CFA00222
57
CFA00221
58
ACN00015
59
ACN00016
60
CMH00101
61
CMH00102
62
CCH00024
CCH02001
CCH02004
Issue 7
DESCRIPTION
QUANTITY
PICK UP CHAIN C/W JOINER LINK
5
JOINER LINK (RIVETED)
A/R
JOINER LINK (COTTER)
A/R
JOINER LINK (CLEAT)
A/R
INNER LINK
A/R
FRONT CONVEYOR REAR SHAFT
1
FRONT LIFT CYLINDER PIN
2
ROLL PIN, 8x50 Z/P
2
WASHER, 12mm FLAT HEAVY DUTY
14
SETSCREW, M12x30 CUPHEAD Z/P
18
2
SIDEPLATE, RIGHT
(U249998)
1
SPROCKET, 1" DUPLEX 14 TOOTH
NLS (60)
NUT, M20 NYLOC
5
WASHER, CUP
10
5
BUSH, GLACIER 3040
5
BUSH, STEEL HARDENED
5
PIN, FRONT SPROCKET PIVOT
5
GREASE NIPPLE, M8 90 DEGREE
5
SKID
1
WASHER, 10mm FLAT
4
NUT, M14 NYLOC
2
WASHER, 14mm FLAT
2
2
SIDEPLATE,LEFT
(F249999)
1
SIDEPLATE, RIGHT
(F249999)
1
SPROCKET, 1" 14 TOOTH
(F249999)
1
SPROCKET, 1" 20 TOOTH
(F249999)
1
CHAIN, 1" 41 LINK,OFFSET & JOIN (F249999)
1
1" JOINER LINK
A/R
1" OFFSET LINK
A/R
Page 49
Page 50
Issue 7
SPARE FILM HOLDER
No. PART NUMBER
ADB00024
1
ADB00025
2
CBC00007
3
CZF02414
4
CFA00313
5
CFA00124
Issue 7
DESCRIPTION
SPARE ROLL HOLDER ASM. COMPLETE
SPARE ROLL HOLDER WELDED FRAME
CAP BLACK PLASTIC 2.3/8" OSF
ROLL HOLDER MOUNT BRCKT
BOLT M12X130 Z/P
NUT M12 NYLOC
QUANTITY
1
1
8
2
6
6
Page 51
34
9
29
25
15
48
2
12
13
35
7
30
8
27
31
39
11
16
6
23
24
28
32
22
44
40
43
26
21
37
36
42
5
17
45
1
46
47
10
14
4
20
3
18
19
20
33
41
34
38
Issue 7
Page 52
HYDRAULIC CONTROL VALVE
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
Part Code
Description
Qty
CFA00568
CHY02020
CVA00103
CVA00117
CVA00118
CVA00119
CVA00120
CVA00122
CVA00175
CVA00176
CVA00177
CVA00178
CVA00179
CVA00180
CVA00186
CVA00187
CVA00189
CVA00191
CVA00192
CVA00193
CVA00194
CVA00195
CVA00196
CVA00197
CVA00198
CVA00199
CVA00200
CVA00201
CVA00203
CVA00204
CVA00205
CVA00206
CVA00207
CVA00255
CVA00300
CVA00301
CVA00302
CVA00303
CVA00304
CVA00305
CVA00306
CVA00307
CVA00308
CVA00309
CVA00310
CVA00311
CVA06009
CVA06011
M6x4.5-Fc=1 SCREW
ADAPTOR 1/4" BANJO ASY COMP
LEVER PIVOT BOX DPC130
SPOOL, DISPENSER ROTATION
SPOOL, CUT & HOLD
SPOOL, CONVEYOR
SPOOL, BALE LIFT
SOLENOID DPC130
END BLOCK VALVE CHEST
PLUG BSP 1/4"
FLOW LIMITER DPC130
VALVE SECTION DPC130 D10
VALVE SECTION DPC130 C10
VALVE SECTION DPC130 C21
SECTION COMPENSATOR DPC130
SEAL KIT DPC130 "O" RINGS
VALVE DPC130 (40-180 BAR)
VALVE DPC130 (180-350BAR)
FILTER LOAD SENSING DPC130
VALVE PRESSURE REDUCING DPC130
O-RING SEAL 5 X 1.2MM PARKER
O-RING SEAL 21.95MM X 1.78MM
CONTROL MODULE DPC130
SOC CAP M5 X 55MM
WASHER ELASTIC M5
O-RING SEAL 11.11MM X 1.78MM
PRESSURE REDUCER DPC130
SOC CAP M6 X 55MM
JOINT DPC130
OPEN BUSHING DPC130
SPRING DPC130
RING 11.2 X 23 X 3MM
PLUG DPC130
TIE ROD KIT VALVE CHEST
DPC130/ELP BODY
DPC130-DPC26 VALVE
UT/DPC130-SDS100 PLUG
LT/DPC26-DPC130-SDM081 PLUG
BSP 1/2 PLUG
ELP/DPC130-BSP WORKING SECTION
FE/DPC130/BR-BSP INLET COVER
DPC130/ELP-SPOOL
M18x1.5 PLUG
M14x1.5 DIN 906 PLUG
DPC130/ELP-FLANGE
UNI-5931/M6x18-8.8 GALVANIZED
CLOSED CTR KIT DPC130
CTE SHUTTLE VALVE DPC
1
1
4
1
1
1
1
4
1
5
2
2
1
1
2
6
1
1
1
1
12
6
4
8
12
8
8
20
1
8
4
4
1
1
1
4
2
1
2
1
1
1
1
1
1
4
1
1
Issue 7
Page 53
Page 54
Issue 7
ROLLER ROTATION BLOCK
No. PART NUMBER
CVA00021
1
CVA00038
2
CVA00039
3
CFA00137
4
CFA00023
Issue 7
DESCRIPTION
ROLLER ROTATION BLOCK COMPLETE
VALVE "CC"
VALVE "NFC"
WASHER, 10mm SPRING
QUANTITY
1
1
1
2
2
Page 55
1
2
3
Page 56
Issue 7
DISPENSER DRIVE BLOCK
1
2
3
CVA00153
CVA00287
CVA00312
CVA00071
Issue 7
VALVE ROTATION 998
CTE PRESSURE REDUCING HS & 998
OVER CENTRE VALVE ASSY
CTE 991BJS DETENT VALVE
1
1
1
1
Page 57
Page 58
Issue 7
STEEL HYDRAULIC PIPES
No. PART NUMBER
1
CFA00251
2
CFA00249
3
CFA00292
4
CHY00039
5
CHY00036
6
CHY00034
7
CFA00316
8
CHY00033
9
CHY00032
10
CHY00054
11
CHY00037
12
CHY00038
13
CHY00015
14
CHY00056
CVA03102
15
CHY00035
16
CFA00101
17
CHY02012
18
CHY00057
DESCRIPTION
WASHER 10mm SKM
WASHER 8mm SKM
SETSCREW M8x10 SOCKET CAP Z/P
STEEL PIPE ASSEMBLY REAR RIGHT
STEEL PIPE ASSEMBLY FRONT RIGHT
STEEL PIPE ASSEMBLY DRAWBAR TOP
BOLT M8x30 Z/P
STEEL PIPE PUMP INTERNAL RETURN
STEEL PIPE TANK RETURN
WASHER 1 1/4" "DOWTY"
STEEL PIPE ASSEMBLY REAR LEFT
STEEL PIPE ASSEMBLY FRONT LEFT
WASHER 1/4" "DOWTY"
PRESSURE TEST ADAPTOR
NON RETURN VALVE 1/4"
STEEL PIPE ASSY DRAWBAR BOTTOM
SETSCREW M8x16 Z/P
WASHER 3/4" "DOWTY"
ADAPTER 5/8"M - 3/4" M
QUANTITY
12
15
12
1
1
1
2
1
1
1
1
1
3
1
1
1
2
1
1
SEE ALSO PAGES 10 AND 11
Issue 7
Page 59
10
11
4
Page 60
Issue 7
ELECTRONIC COMPONENTS 1
No. PART NUMBER
1
CEL00046
2
CEL00047
3
CEL00045
4
CEL00619
5
CEL00048
CFA00299
CFA00082
CFA00083
6
CEL00050
7
CEL00618
8
CEL00049
9
CEL00038
CFA00314
CFA00320
CFA00321
10
CEL00193
11
CEL00128
Issue 7
DESCRIPTION
SLIPRING LOWER LOOM
SLIPRING
SLIPRING UPPER LOOM
LOOM 998 TOP ARCH
POTENTIOMETER
SETSCREW, M4x16 SOCKET CAP Z/P
WASHER 4mm SHAKEPROOF
WASHER 4mm FLAT
COMPARATOR
MAIN MACHINE LOOM
POTENTIOMETER EXTENSION LOOM
SAFETY ARM SWITCH
SETSCREW, M5x40 Z/P
WASHER 5mm FLAT
NUT, M5 NYLOC
MODULE CONSTANT CURRENT
POTENTIOMETER 991 LIFTARM
QUANTITY
1
1
1
1
2
4
4
4
1
1
1
2
4
8
4
1
1
Page 61
Page 62
Issue 7
ELECTRONIC COMPONENTS 2
No. PART NUMBER
1
CEL00168
2
CEL00031
3
CEL00064
4
CPL00012
5
CEL00035
6
CEL00017
CFA00099
CFA00144
CFA00131
CFA00047
7
CEL00059
CFA00261
CFA00084
CFA00262
Issue 7
DESCRIPTION
CONTROL EXPERT 998
POWER LEAD (BATTERY)
POWER LEAD (EURO)
SUCTION PAD FOR CONTROL BOX
SENSOR
MAGNET, LARGE
SETSCREW, M6x40 Z/P
WASHER 6mm FLAT
NUT, M6 NYLOC
SETSCREW, M6x30 Z/P
MAGNET, SMALL
SETSCREW, M5x25 CSK HEX STAINLESS
WASHER 5mm SPRING STAINLESS
NUT, M5 WING STAINLESS
QUANTITY
1
1
1
1
4
4
4
4
4
1
2
2
2
2
Page 63
Page 64
Issue 7
LIGHTING
No. PART NUMBER
1
CEL00072
2
CEL00079
3
CEL00074
4
CEL00073
5
CEL00078
6
CEL00075
7
CEL00076
8
CEL00077
CFA00288
CFA00321
CEL00111
Issue 7
DESCRIPTION
QUANTITY
7 PIN PLUG & LOOM
1
FRONT RECTANGULAR REFLECTOR (WHITE)
2
FRONT MARKER LIGHT & LOOM
2
JOINER LOOM
1
SIDE RECTANGULAR REFLECTOR (ORANGE)
4
LEFT HAND REAR LIGHT
1
RIGHT HAND REAR LIGHT
1
REAR TRIANGULAR REFLECTOR (RED)
2
SETSCREW, M5x16 PAN HEAD
4
NUT, M5 NYLOC
4
WORK LIGHT & LOOM
1
Page 65
Page 66
Issue 7
DECALS
No. PART NUMBER
CST00012
1
CST00017
2
CST00022
3
CST00014
4
CST00033
5
CST00036
6
CST00016
7
CST00015
8
CST00023
9
CST00024
10
CST00018
11
12
CST00040
13
CST00032
14
CST00019
15
CST00020
16
CST00021
17
CST00056
18
CST00026
Issue 7
DESCRIPTION
DECAL SET COMPLETE
HANDS CLEAR OF ROTATING PARTS
PLASTIC FILM PATH
WARNING! ROTATING ELEMENTS
"MCHALE"
"998"
HYDRAULIC SYSTEM AWARENESS
REMOVE IGNITION KEY
PTO SPEED
CHECK OIL LEVEL
DRAWBAR CRUSH AREA
CHASSIS PLATE
DISPENSER ROTATION WARNING
LIFTING HOOK
HAND CRUSH AREA
CHECK WHEEL NUTS
CHECK TYRE PRESSURE
HYDRAULIC ACCUMULATOR WARNING
HAND ENTRAPMENT
QUANTITY
1
2
2
2
4
4
2
1
1
1
4
1
2
4
4
2
2
3
2
Page 67
Notes
Page 68
Issue 7
998 Optional Extra’s Parts Contents
Title
Page
Round Bale Kit
68
Air Brake Kit
70
Small Bale Kit
72
Issue 7
Page 69
Page 70
Issue 7
ROUND BALE KIT
No. PART NUMBER
ACH00109
1
CZH02167
2
CZH02168
3
ACH00111
4
ACH00110
5
CMH00252
6
CZH02169
7
ACH00112
8
CFA00399
9
CFA00024
10
CFA00201
11
CFA00123
12
CMH00392
13
CMH00393
14
CFA00013
15
CFA00128
16
CFA00408
17
CFA00110
18
CMH00015
19
CFA00005
20
CWH00021
21
CTP00036
Issue 7
DESCRIPTION
ROUND BALE ATTACHMENT
6MM L BALE ATTACHMENT BRCKT.
6MM L BALE ATTACHMENT BRCKT.
ROUND BALE PIVOT PIN ASM.
ROUND BALE PIPE ASSEMBLY
BUSH 41X58X40&12MM C.HOLE
6MM L FRONT ATTACHMENT BRCKT
WHEEL BRACKET ASSEMBLY
SETSCREW M16X30 Z/P
SETSCREW M10X25 Z/P
WASHER FLAT 10MM Z/P
NUT M10 NYLOC
PIN 25X355&2X5.5MM C.HOLES
PIN 25X155&2X8MM C.HOLES
SPLIT PIN 5X50 ZINC PL
NUT M16 NYLOC
BOLT M16X340 Z/P
ROLL PIN 12 X60
PIN 1” TOP LINK
LINCH PIN 10MM
WHEEL ASY 4.00 / 4.080 - 8
CAT 2 TOP LINK
QUANTITY
1
1
1
1
1
1
1
1
2
1
1
1
2
1
6
6
4
1
1
1
5
1
Page 71
14
12
11
10
9
9
2
1
3
1
6
4
5
7
8
13
8
Page 72
Issue 7
AIR BRAKE KIT
No. PART NUMBER
1
CVA00124
2
CHY00125
3
CVA00128
4
CHY00128
5
CHY00126
6
CVA00123
7
CHY00127
8
CHY00124
9
CVA00126
10
CVA00127
11
CVA00132
12
CVA00125
13
CVA00131
14
CVA00130
Issue 7
DESCRIPTION
AIR BRAKE ACTUATOR
HOSE A/B 1.85M LONG 25MM X 5.5MM
TEE PIECE AIR BRAKE VALVE
HOSE A/B 1M LONG 15MM X 1.5MM
AIR BRAKE AIR VALVE
AIR BRAKE QUICK FIT COUPLING
AIR BRAKE QUICK FIT BRACKET (RED)
AIR BRAKE QUICK FIT BRACKET (YELLOW)
AIR BRAKE AIR TANK
RELIEF VALVE, AIR BRAKE TANK
DRAIN TAP, AIR BRAKE TANK
QUANTITY
2
1
1
1
1
1
1
2
2
1
1
1
1
1
Page 73
2
3
1
4
5
Page 74
Issue 7
SMALL BALE KIT
No. PART NUMBER
1
ARC00016
2
CFA00275
3
CFA00222
4
CFA00126
5
CVA03004
Issue 7
DESCRIPTION
ROLLER CRADLE BALAST BRACKET ASSY
SETSCREW M14 X 35 FLANGED Z/P
WASHER FLAT 14MM Z/P
NUT M14 NYLOC
FLOW CONTROL VALVE
QUANTITY
2
4
4
4
1
Page 75
Notes
Page 76
Issue 7

998 SPARE PARTS MANUAL ENGLISH ISSUE 7.pub

Transcription

Similar documents

Spare Parts Book 991B-BC-BE-BER-BJS