TRENZ ELECTRONIC

Transcription

TRENZ ELECTRONIC

TRENZ ELECTRONIC
SHORT FORM CATALOGUE
updated february 2016
Company Prole
Since 1992, Trenz Electronic GmbH
successfully operates as a development service enterprise in the electronics branch. Our services include
design-in support as well as turnkey
design which typically cover all steps
from product specication, hardware
and software design up to prototyping
and production.
Hardware Design
• System Architecture and Design
• Hardware Integration (Design-In)
• Ultrafast Digital Logic
• Analog and Mixed Signal
• Digital Signal Processing
• Schematic Capture and PCB Layout
HDL Design
• FPGA and System-On-Chip Design
• System Design and Synthesis
• HDL Design (VHDL,Verilog)
• Integration of Soft-Cores
(Xilinx MicroBlaze, ARM Cortex …)
• USB, PCI-Express, Gigabit Ethernet
• Ultrafast ADC/DAC Interfaces
Software Development
• Device Driver and Application
Software development
• Software and Firmware
development
We are particularly specialized in the
design of high-speed data acquisition,
high-accuracy measurement and embedded digital signal processing systems based on FPGA and ARM
architectures.
We maintain long-term customer relationships, characterized by exibility
and technical competence.
ISO 9001:2008
ISO 14001:2004
(quality management)
(environmental
certied
management) certied
Trenz Electronic GmbH
Holzweg 19A, 32257 Bünde (Germany)
Phone: +49 (0) 5223 65301-0
Fax: +49 (0) 5223 65301-30
E-Mail: info@trenz-electronic.de
Web: www.trenz-electronic.de
www.trenz-electronic.de
2
Index
Trenz Electronic
Company Prole ................................................... 2
Table of contents ................................................... 3
TE0808 (Zynq UltraScale+) ................................. 4
TE0729 (Zynq) ...................................................... 5
TE0722 (Zynq) ...................................................... 6
TE0723 (Zynq) ...................................................... 7
TE0726 (Zynq) ...................................................... 8
TE0728 (Zynq) ...................................................... 9
TE0720 (Zynq) .................................................... 10
TE0715 (Zynq) .................................................... 11
TE0782 (Zynq) .................................................... 12
TE0725 (Artix-7) .................................................. 13
TE0710 (Artix-7) .................................................. 14
TE0711 (Artix-7) .................................................. 15
TE0712 (Artix-7) .................................................. 16
TE0790 (XMOD) .................................................. 17
TE0841 (Kintex UltraScale) ................................ 18
TE0741 (Kintex-7) ................................................ 19
TE0600 (Spartan-6) ............................................ 20
TE Carrier Boards ................................................ 21
Module series comparison table ......................... 22
Module series comparison table ......................... 23
Digilent
Digilent Company Profile .................................... 24
Basys 3 ................................................................ 25
Nexys Video ........................................................ 26
Nexys 4 DDR ....................................................... 27
ZYBO Development Board .................................. 28
Zedboard Development Board ........................... 29
Genesys 2 ........................................................... 30
Electronics Explorer ............................................ 31
NetFPGA SUME+NetFPGA 1G CML ................. 32
NI LabVIEW Home Edition ................................. 33
NI myRIO Accessory Board ................................ 34
Analog Discovery 2 ............................................. 36
Pmods (Peripheral Modules) .............................. 38
Programming Solutions ...................................... 39
chipKIT, chipKIT PRO ......................................... 40
Xilinx
Boards and kits ................................................... 42
XESS Corporation
XuLA2 [Spartan-6] series ................................... 43
Sundance
Sundance EMC2-DP .......................................... 44
Red Pitaya
Company introduction & products ...................... 46
MYIR
Development Board ............................................ 48
Z-turn Board ........................................................ 50
inrevium
inrevium Boards .................................................. 52
inrevium Option Cards ........................................ 54
SoC-e
Company prole & products ............................... 55
cronologic
PCie digitizers ..................................................... 56
Ndigo series ........................................................ 57
Violet series ......................................................... 58
www.trenz-electronic.de
3
5.2
TE0808 UltraSOM+ Series
Xilinx Zynq UltraScale+, DDR4, Flash, 20 x Transceiver
7.6
Overview
The Trenz Electronic TE0808 is an industrial-grade FPGA
modules integrating a Xilinx Zynq UltraScale+, max. 4 GByte
DDR4 SDRAM with 32-Bit width, max. 512 MByte Flash
memory for conguration and operation, up to 256 MByte
HyperFlash, 20 Gigabit transceivers, and powerful switchmode power supplies for all on-board voltages. A large
number of congurable I/O‘s is provided via rugged highspeed stacking connections.
All this in a compact 5.2 x 7.6 cm form factor, at the most
competitive price.
All modules produced by Trenz Electronic are developed
and manufactured in Germany.
Key Features
Extended
device
life cycle
Ÿ SoC: ZYNQ UltraScale+ ZU9EG C900 Package (ZU4EV,
ZU5EV, ZU7EV, ZU6EG, ZU15EG)
Rugged for
industrial
applications
Ÿ Memory:
Ÿ
Other assembly options for cost or performance
optimization available or high volume prices on request.
DDR4
GTH 12 LANES
ZYNQ Ultrascale+
ZU9EG
PS GTR 4 LANES
GTH 4 LANES
HP I/O 72
HP I/O 32
HyperRAM
64MB Flash Dual
Quad SPI
HyperRAM
JTAG
HyperRAM
Power subsystem
DC/DC and LDO's
www.trenz-electronic.de/te0808
4
PLL
MSP430
Supervisor
160 Pin Connector
Ÿ
48 HD I/O
Ÿ
Ÿ
160 Pin Connector
GTCLK 3 Inputs
Ÿ
PS 65 I/O
Ÿ
160 Pin Connector
Ÿ
- 32-Bit DDR4 - 4 GByte max
- 2 x Hyper RAM - 2 x 32 MByte max
- SPI Boot Flash Dual Parallel - 512 MByte max
- XTRMFlash (or HyperFlash) - 256 MByte max
User I/O‘s
- MIO 65, HD 48 (all), HP 96 (2 banks)
- Serial transceiver: GTR 4 (all) + GTH 16 (all)
- GT clocks, SYSMON I2C
- PLL clock inputs and outputs
Size: 52 x 76 mm, 3 mm mounting holes for skyline heat
spreader
B2B connectors: 3 x 160 pin
Si5345 - 12 output PLL
All power supplies on board, single 3.3V Power required
- 14 on-board DC/DC regulators and 13 LDO’s
- MSP430 power monitor and controller
- LP, FP, PL separately controlled power domains
Support for all boot modes (except NAND) and
scenarios
Support for any combination of PS connected
peripherals
5
TE0729 Series
Xilinx Zynq, 1x Gig ETH, 512 MByte DDR3, 2x 100MBit ETH, 4 GByte eMMC, 3.3V Only
7
Overview
The Trenz Electronic TE0729 is an industrial-grade FPGA
module integrating a Xilinx Zynq-7020 with a gigabit Ethernet
transceiver, 2 x 100 MBit Ethernet, 512 MByte DDR3 SDRAM,
32 MByte Flash memory for conguration and operation, and
powerful switch-mode power supplies for all on-board
voltages. A large number of congurable I/O‘s is provided via
rugged high-speed stacking strips.
Extended
device
life cycle
Key Features
Rugged for
industrial
applications
Ÿ Zynq XC7Z020-2CLG484I
- 512 MByte DDR3 SDRAM
- 1 Gigabit Ethernet PHY
- 2 x 100 MBit Ethernet PHY
- RTC
- 4 GByte eMMC
- 32 MByte QSPI Flash
- USB 2.0 PHY
Ÿ 5 pairs LVDS IO, 2.5V VCCIO
Ÿ 48 I/O Differentially routed variable VCCIO
Ÿ 48 I/O variable VCCIO
Ÿ 30 I/O xed 3.3V VCCIO
Ÿ 8 MIO 3.3V VCCIO
Ÿ 6 MIO (SD Card Interface)
SDIO
Power Subsystem DC/DC
Ÿ Cooling Solution available
ZYNQ-7020
HR I/O 96
LVDS 5 pairs
MIO 8 I/O
HR I/O 30
120 Pin Connector
120 Pin Connector
optimization available or high volume prices
on request.
MAC EEPROM
MAC EEPROM
MAC EEPROM
JTAG
RTC
1G ETH PHY
100M ETH PHY
100M ETH PHY
32MB SPI Flash
5
1.8
TE0722 Series
Xilinx Zynq, Dual Core ARM A9+, 16 MByte SPI Flash, DIP40 Form Factor
5.1
Overview
The DIPFORTy1 "Soft Propeller" is based on the Xilinx ZYNQ7000, a System on Chip which contains a FPGA and a Dual
Core ARM A9+ processor with enough logic gates to become
a Propeller. The board also has 16 MByte of Flash used for
conguration and everything ts on a Propeller-compatible DIP
40 pinout.
DIPFORTy1 "Soft-Propeller" is the lowest cost ZYNQ based
module ever made and the rst ZYNQ module that can use
existing bases and project boards (Parallax Propeller chip
compatibility). All this in a compact 1.8 x 5.1 cm form factor, at
the most competitive price.
All modules produced by Trenz Electronic are developed and
manufactured in Germany.
er“
"Ideal für Mak
Extended
device
life cycle
Key Features
Ÿ Xilinx ZYNQ-7: XC7Z010-CLG225
- 16 MByte SPI Flash (primary boot)
- 33.333 MHz Clock (MEMS Oscillator)
Ÿ Dual Core ARM A9+
Ÿ DIP40 form factor
- 2 x 20 holes for socket pins or pin-header
- Size: 18 x 51 mm
Ÿ Total user accessible PL I/O: 46 (+3 Input only)
- DIP40 header pins: 34 I/O
- XMOD J1: 6 I/O
- XMOD J2: JTAG + 2 I/O (or 3 input + 2 I/O)
- XMOD J3: 4 I/O
Power Supply
3.3V Input
Micro
SD
JTAG+
2 I/O
8 I/O
Ÿ 3.3V single supply
Ÿ RGB LED (PL I/O connected)
Ÿ "Done" LED (inverted polarity)
optimization available or high volume prices on request.
XC7Z010
16 I/O
Si1143
33.3 MHz
Osc.
6
16 MByte
SPI Flash
18 I/O
RGB
LED
20 pos. 2.54 mm holes
Ÿ Sil1143 Proximity and ambient light sensor
20 pos. 2.54 mm holes
Ÿ User LED (ARM CPU MIO GPIO)
Ÿ MicroSD Card socket (MIO, ZYNQ secondary boot media)
Arduino
TE0723 Series
Xilinx Zynq, 2x ARM Cortex A9, LPDDR2 Memory, USB OTG, On-board USB JTAG and UART
Shield
Overview
The Trenz Electronic TE0723 „ArduZynq“ is a Arduino
compatible FPGA module integrating a Xilinx Zynq-7010, 64
MByte LPDDR2, and 16 Megabyte SPI Flash Memory for
conguration and operation. The "ArduZynq" is the lowest cost,
Linux ready solution to use the latest FPGA: the Xilinx 7 series.
Use it as a FPGA development platform, or run Linux on the
Cortex A9 cores.
Extended
device
life cycle
er“
"Ideal für Mak
Key Features
Ÿ Xilinx XC7Z010-1CLG225I
Ÿ Form Factor: Arduino Shield
Ÿ Dual ARM Cortex-A9
Ÿ 64 MByte LPDDR2
Ÿ 16 MByte SPI Flash memory
Ÿ 12 MHz MEMS Oscillator low power consumption
Ÿ Hi-Speed USB2.0 ULPI Transceiver
Ÿ 23 FPGA I/O‘s available on board-to-board connectors
Ÿ MicroSD Card socket
Ÿ Micro USB OTG
Ÿ RGB LED (PL I/O connected)
Ÿ "Done" LED (inverted polarity)
Ÿ On-board USB JTAG and UART
Ÿ Temperature range -40° C to 85° C
128 MByte
DDR3L
Power Reset
6 A in
6 IO +
I2C
XC7Z010
Analog
MUX
6 IO +
UART
Dual PMOD
8 I/O
2.54 mm holes
2.54 mm holes
2.54 mm holes
Other assembly options for cost or performance optimization
available or high volume prices on request.
Micro
SD
USB
OTG
33.3 MHz
Osc
16 MByte
SPI Flash
2.54 mm holes
Power Supply
3.3V Input
Ÿ CERN Open Hardware Licence 1.2
RGB
LED
7
R
pberry P
as
I
TE0726 Series
Xilinx Zynq, 64 MByte LPDDR, 16 MByte Flash, 100 MBit Ethernet RJ45
Overview
The Trenz Electronic TE0726 „ZynqBerry“ is a Rasberry Pi
compatible FPGA module integrating a Xilinx Zynq-7010,
4 USB ports, a Ethernet port and 16 MByte Flash memory for
conguration und operation.
er“
"Ideal für Mak
Extended
device
life cycle
Key Features
Ÿ Xilinx Zynq XC7Z010-1CLG225I
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
optimization available or high volume prices
on request.
4x USB 2.0
Host
2 x 20 pin Rasperry HAT header
Ÿ
- 64 MByte LPDDR2
- 16 MByte Flash
LAN9514 USB Hub with Ethernet
- 4 x USB with power switches
- 100 MBit Ethernet RJ45
Micro SD card slot
HDMI Typ A
DSI Connector (Display)
CSI-2 Connector (Camera)
Micro USB
- power input
- USB UART
- JTAG ARM- und FPGA-Debug
3.5 mm audio plug (PWM Audio output only)
Raspberry Pi Model 2 form faktor
HAT header with 26 I/O‘s
RJ45
10/100 Ethernet
CSI-2
Camera
DSI Display
26 I/O
ZYNQ-7010
HDMI Out
3.5 mm Plug
Stereo
Audio Out
Analog input
DDR3L
JTAG
UART
SPI Flash
Micro USB, PWR + FT2232H
8
Power (DC/DC)
6
TE0728 Series
Xilinx Zynq, 2 × Cortex-A9, DDR3, Flash, 2 × Ethernet, CAN, Automotive
6
Overview
The Trenz Electronic TE0728 is a FPGA module integrating a
Xilinx Automotive Zynq-7020, 512 MByte DDR3 SDRAM with
16-Bit width, 16 MByte Flash Memory for conguration and
operation, two 100 Megabit Ethernet transceivers, and
voltages. A large number of congurable I/Os is provided via
rugged high-speed stacking strips.
Within the complete module only automotive components are
installed. The temperature range is between -40°C and
+105°C. All this in a compact 6 x 6 cm form factor, at the most
competitive price.
Key Features
I2C
CAN
12V
DC/DC
+
watchdog
PL
(Programmable Logic)
CAN
JTAG
User I/O
PS User I/O
80 Pin
Assembly options for cost or performance
optimization available upon request.
Rugged for
automotive
applications
PL User I/O
10/100/1000
Ethernet PHY
PL User I/O
PL User I/O
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Extended
device
life cycle
10/100/1000
Ethernet PHY
Ÿ
Xilinx Zynq XA7Z020-1CLG484Q (Automotive)
Rugged for shock and high vibration
2 x ARM Cortex-A9 MPCore
2 x 100 MBit Ethernet transceiver (PHY)
16-Bit-wide 512 MByte DDR3 SDRAM
16 MByte QSPI Flash memory (with XiP support)
Plug-on module with 3 x 80-pin high-reliability highspeed strips
124 FPGA I/O‘s (62 LVDS pairs possible) and 38 PSMIOs available on
Board-to-board connectors
CAN transceiver (PHY)
Temperature compensated RTC (real-time clock)
12 V power supply with watchdog
On-board high-efciency DC-DC converters
System management and power sequencing
eFUSE bit-stream encryption
AES bit-stream encryption
3 user LEDs
Temperature Range -40°C to +105°C
Evenly-spread supply pins for good signal integrity
80 Pin
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
80 Pin
9
TE0720 Series
Xilinx Zynq, 2 × Cortex-A9, DDR3, Flash, GBit Ethernet, USB
Overview
Trenz Electronic TE0720 are industrial-grade SoC modules
integrating a Xilinx Zynq-7000 SoC, a gigabit Ethernet
transceiver, 1 gigabyte DDR3 SDRAM with 32-Bit width, 32
megabyte Flash memory for conguration and operation, a
USB ULPI transceiver, and powerful switch-mode power
supplies for all on-board voltages. A large number of
congurable I/O‘s is provided via rugged high-speed stacking
strips. All modules in 4 x 5 cm form factor are mechanically
compatible.
All this on a tiny footprint, smaller than a credit card, at the most
competitive price.
Key Features
Extended
device
life cycle
Ÿ Industrial-grade Xilinx Zynq-7000 (Z-7020) SoM,
supported by the free Xilinx Vivado WebPACK tool
Rugged for
industrial
applications
Ÿ Rugged for shock and high vibration
Ÿ 2 × ARM Cortex-A9
Ÿ 10/100/1000 tri-speed gigabit Ethernet transceiver
(PHY) with SGMII
- MAC Address EEPROM
Ÿ
Ÿ
Ÿ
Ÿ
32-Bit-wide 1 GByte DDR3 SDRAM
4 GByte eMMC (up to 64 GB)
Plug-on module with 2 × 100-pin and 1 × 60-pin
high-speed hermaphroditic strips
Ÿ 152 FPGA I/O‘s (75 LVDS pairs possible) and 14
PS-MIO available on board-to-board connectors
Ÿ USB 2.0 high-speed ULPI transceiver
Ÿ On-board high-efciency DC-DC converters
- 4.0 A x 1.0 V power rail
USB
PHY
10/100/1000
Ethernet PHY
ARM
ARM
Cortex-A9 Cortex-A9
User I/O
PS
(Processing System)
PL
User I/O
User I/O
I2C
magnetometer)
Ÿ Evenly-spread supply pins for good signal integrity
4-64
GByte
EMMC
100 Pin
SHA-256 authentication chip with unique serial
number
Ÿ Temperature compensated RTC (real-time clock)
Ÿ 3 user LEDs
Ÿ Optional MEMS sensor (3D accelerometer and 3D
System Mgmt.
Power Seq.
32 MByte
QSPI
Flash
MAC
3D acc.
EEPROM
RTC
Address
3D mag.
(SHA-1)
EEPROM
10
JTAG
100 Pin
Ÿ
Ÿ
Ÿ
Ÿ
1 GByte
DDR3
SDRAM
User I/O
60 Pin
TE0715 Series
Xilinx Zynq, Cortex-A9, DDR3, Flash, GBit Ethernet, 4 x Transceiver
Overview
Trenz Electronic TE0715 are industrial-grade SoC modules
integrating a Xilinx Zynq-7000 SoC, a gigabit Ethernet
transceiver (physical layer), 1 gigabyte DDR3 SDRAM with
32-Bit width, 32 megabyte Flash memory for conguration and
operation, 4 transceivers, a USB ULPI transceiver, and
powerful switch-mode power supplies for all onboard
rugged high-speed stacking strips. All modules in 4 x 5 cm
form factor are mechanically compatible.
All this on a tiny fooprint, smaller than a credit card, at the most
competitive price.
Key Features
Ÿ Industrial-grade Xilinx Zynq-7000 (Z-7015, Z-7030) SoM ,
Extended
device
life cycle
Ÿ ARM dual-core Cortex-A9
Ÿ 10/100/1000 tri-speed gigabit Ethernet transceiver
Rugged for
industrial
applications
(PHY) with SGMII
Ÿ 32-Bit-wide 1 GByte DDR3 SDRAM
Ÿ 32 MByte QSPI Flash memory (with XiP support)
Ÿ Programmable clock generator
- Transceiver clock (default 125 MHz)
Ÿ Plug-on module with 2 × 100-pin and 1 × 60-pin
Ÿ 132 FPGA I/O‘s (65 LVDS pairs possible) and 14
PS-MIO available on board-to-board connectors
GTP/GTX transceiver
- GTP/GTX (high-performance transceiver) clock
input
Ÿ USB 2.0 high-speed ULPI transceiver
JTAG
10/100/1000
Ethernet PHY
Temperature compensated RTC (real-time clock)
User I/O
100 Pin
System management
100 Pin
32 MByte
QSPI
Flash
User I/O
User I/O
User LED
I2C
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
User I/O
60 Pin
Ÿ 4 GTP/GTX (high-performance transceiver) lanes
System
Mgmt
Oscillator
MAC
Address
EEPROM
11
8.5
TE0782 Series
Xilinx Zynq, 2 × Cortex-A9, DDR3, Flash, 2 × GBit Ethernet, 2 × USB, 16 × Transceiver
8.5
Overview
The Trenz Electronic TE0782 series are industrial-grade Xilinx
Zynq-7 XC7Z035, XC7Z045 or XC7Z100 modules with 1 GByte
DDR3 SDRAM, 4 GByte eMMC, 16 GTX high-performance
transceiver lanes, 32 MByte QSPI Flash memory for
conguration and operation, and powerful switch-mode power
supplies for all on-board voltages.
A large number of congurable I/O‘s is provided via rugged
high-speed stacking strips. All this in a 8.5 x 8.5 cm form factor
at the most competitive price.
Key Features
Extended
device
life cycle
Ÿ Industrial-grade Xilinx Zynq-7 XC7Z035, XC7Z045 or
PL User I/O
JTAG
I2C
PL User I/O
USB PHY
USB PHY
GBit
Ethernet PHY
MAC
Address
EEPROM
RTC
ARM
ARM
Cortex-A9 Cortex-A9
1 GByte
DDR3
SDRAM
PS
(Processing System)
4-64
GByte
eMMC
32 MByte
QSPI
Flash
GTX transciever
Clock
Generator
172 Pin
12
MAC
Address
EEPROM
PL
PL User I/O
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
GBit
Ethernet PHY
Ÿ
Ÿ
172 Pin
GTX transciever
Ÿ
Ÿ
Ÿ
172 Pin
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
XC7Z100 SOM
Dual ARM Cortex-A9 MPCore
Real Time Clock
2 x Hi-Speed USB2.0 ULPI Transceiver PHY
2 x Gigabit Ethernet Transceiver PHY
2 x Ethernet MAC Address EEPROM
1 GByte DDR3 SDRAM
32 MByte QSPI Flash memory
4 GByte eMMC (optional up to 64GByte)
Optional 2 x 8 MByte HyperRAM (max 2 x 32 MByte
HyperRAM)
Si5338 PLL for GTX clocking
Plug-on module with 3 x 160-pin high-speed strips
16 GTX high-performance tranceiver lanes ,
GTX high-performance
Transceiver clock input
254 FPGA I/O‘s (125 LVDS pairs possible) available
on board-to-board connectors
Temperature range: -40° C to +85° C
Rugged for
industrial
applications
25 MHz
Oscillator
7.3
TE0725 Series
Xilinx Artix-7, 32 MByte Flash, 88 IO's, 2x 50 Pin Headers 2.54 mm Pitch
3.5
Overview
The Trenz Electronic TE0725 is a low cost small-sized FPGA
module integrating a Xilinx Artix-7 (15T - 100T) and 32 MByte
Flash memory for conguration and operation. The 2 x 50 pin
header with a 2.54 mm standard pitch ts perfect on a
breadboard.
Key Features
Extended
device
life cycle
Ÿ Xilinx Artix-7 15T up to 100T
Ÿ commercial temperature grade (industrial on request)
Rugged for
industrial
applications
Ÿ 32 MByte Flash memory
Ÿ 2 x 50 pin headers with 2.54 mm pitch, ideal for
breadboard use
Ÿ 88 IO's (42 + 42 + 4)
Ÿ 100 MHz System Clock
Ÿ I2C EEProm
Ÿ 3.3V single supply with on board voltage regulators
Ÿ Size 73 x 35 mm
Ÿ JTAG connector
Ÿ 2 LEDs
Ÿ optional HyperRAM (8 to 32 MByte)
Optical 250 MB/s
POF Modul
Power Subsystem
DC/DC and LDO's
Ÿ optional Fiber Optic module
Hyper
RAM
JTAG
42 I/O
2 x 50 Pin 100 mil header
ARTIX-7
15T - 100T
42 I/O
3 I/O + RST
Other assembly options for cost or performance optimization
available or high volume prices on request.
SPI Flash
13
TE0710 Series
Xilinx Artix-7 T, DDR3, Flash, 2 × 100 MBit Ethernet
Overview
Trenz Electronic TE0710 are industrial-grade FPGA modules
integrating a Xilinx Artix-7 T FPGA, two megabit Ethernet
transceivers (physical layer), 512 Mbyte DDR3 SDRAM with
8-Bit width, 32 megabyte Flash memory for conguration
and operation, and powerful switch-mode power supplies
for all on-board voltages. A large number of congurable
I/O‘s is provided via rugged high-speed stacking strips.
All modules in 4 x 5 cm form factor are mechanically
compatible.
All this on a tiny footprint, smaller than a credit card, at the
most competitive price.
Ÿ Industrial-grade Xilinx Artix-7 (15T to 100T) SoM,
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
512 MByte DDR3 SDRAM
Dual 100 MBit Ethernet PHY
MAC Address EEPROM
100 MHz programmable MEMS oscillator
Plug-on module with 2 × 100-pin high-speed
hermaphroditic strips
112 FPGA I/O‘s (51 differential pairs) available
User LED
Evenly-spread supply pins
for good signal integrity
Extended
device
life cycle
Rugged for
industrial
applications
512 MByte
DDR3 SDRAM
JTAG
10/100
Ethernet PHY
100 Pin
10/100
Ethernet PHY
Xilinx FPGA
Artix-7 T
(15T to 100T)
User I/O
User I/O
32 MByte
MAC
QSPI
Address
Serial Flash EEPROM
14
100 MHz
Oscillator
100 Pin
Key Features
TE0711 Series
Xilinx Artix-7 T, DDR3, Flash, 2 × 100 MBit Ethernet
Overview
integrating a Xilinx Artix-7 T FPGA, 32 Mbyte Flash memory
for conguration and operation, and powerful switch-mode
power supplies for all on-board voltages. A large number of
congurable I/O‘s is provided via rugged high-speed
stacking strips. All modules in 4 x 5 cm form factor are
mechanically compatible.
most competitive price
manufactured in Germany..
Key Features
Ÿ Industrial-grade Xilinx Artix-7 (15T to 100T) SoM,
Extended
device
life cycle
Rugged for
industrial
applications
Ÿ 100 MHz programmable MEMS oscillator
Ÿ 178 FPGA I/O‘s (84 differential pairs) available
Ÿ System management and power sequencing
Ÿ eFUSE bit-stream encryption
60 Pin
User I/O
Ÿ AES bit-stream encryption
Ÿ 3 user LEDs
Ÿ FTDI USB to UART/FIFO bridge
USB to
UART/FIFO
Bridge
JTAG
Xilinx FPGA
Artix-7 T
(15T to 100 T )
100 Pin
User I/O
User I/O
100 Pin
32 MByte
QSPI
Serial Flash
100 MHz
Oscillator
15
TE0712 Series
Xilinx Artix-7 T, DDR3, Flash, 100 MBit Ethernet, 4 x Transceiver, High pin count
Overview
integrating a Xilinx Artix-7 T FPGA, a megabit Ethernet
transceiver (physical layer), 1 gigabyte DDR3 SDRAM with 32Bit width, 32 megabyte Flash memory for conguration and
operation, and powerful switch-mode power supplies for all
on-board voltages. A large number of congurable I/O‘s is
provided via rugged high-speed stacking strips. All modules in
4 x 5 cm form factor are mechanically compatible.
competitive price.
Key Features
Ÿ Industrial-grade Xilinx Artix-7 (15T to 200T)
SoM, supported by the free Xilinx Vivado WebPACK tool
Extended
device
life cycle
Rugged for
industrial
applications
Ÿ 1 GByte DDR3 SDRAM
Ÿ 100 MBit Ethernet PHY
- Transceiver clock (default 125 MHz)
- Fabric clock (default 200 MHz)
Ÿ 158 FPGA I/Os (78 differential pairs) available on
board-to-board connectors
60 Pin
Ÿ 4 GTP (high-performance transceiver) lanes
User I/O
- GTP (high-performance transceiver) clock input
Clock
Generator
25 Mhz
Oscillator
- 12 A x 1.0 V power rail
GTP transceiver
Ÿ System management and power sequencing
JTAG
Ÿ eFUSE bit-stream encryption
Xilinx FPGA
Artix-7 T
(15T to 200T)
Ÿ User LED
100 Pin
Ÿ AES bit-stream encryption
User I/O
User I/O
32 MByte
QSPI
Serial Flash
16
MAC
Address
EEPROM
1 GByte
DDR3
SDRAM
100 Pin
10/100
Ethernet PHY
TE0790 / TE0790-01L
Xmod Form-Factor, FT2232H, Lattice XO2-256 CPLD, 4 Position DIP Switch
Xmod
Xmod
Overview
Xmod-USB-X is a universal USB adapter with 2 channels
based on FTDI FT2232H USB2 HS Interface chip.
In the consigned default conguration Port A is JTAG and Port
B is a serial interface.
FT2232H port A and B are connected to small on-board
programmable CPLD to allow exible application specic
remappings of FT2232H functions into 8 user I/O pins of single
Xmod 12x8 Module.
Minimum PCB area on base board to support JTAG function
5 x 10 mm (does not include mounting hole space).
TE0790 is compatible with Xilinx Tools in contrast to the
TE0790-01L, that can be used exibly.
Key Features
Ÿ Xmod form-factor
- Supported base slots: 6 x 2, 8 x 4, 10 x 6, 12 x 8, 5 x 2
5x3
- size: 20 x 25 mm
- M3 mounting hole
Ÿ FT2232H
- Channel B RX/TX LED's (on top, not visible from front)
- Mini-USB connector (more rigid then micro-USB)
- 93C56 EEPROM
Ÿ Lattice XO2-256 CPLD
- On board programmable using Lattice tools
- 8 universal I/O pins
- VCCIO either 3.3 V or user supplied (1.8 to 3.3V)
- Red user LED (front visible)
- 12 MHz clock from on-board Oscillator
Ÿ LDO for optional USB power
Ÿ Green Power-on LED (front visible)
Ÿ User button (front accesible)
Ÿ 4 position DIP switch
- Choose CPLD program mode
- FTDI EEPROM disable (not implemented in PCB REV 1)
- Use VIO same as VCC
- Use VCC from USB
17
TE0841 Series
Xilinx Kintex UltraScale, DDR4, Flash, +8 Transceiver
Overview
The Trenz Electronic TE0841 are industrial-grade FPGA
modules integrating a Xilinx Kintex UltraScale KU35 or KU40
with DDR4 SDRAM with 2 x 16-Bit width, max 256 MByte
Flash memory for conguration and operation, and powerful
switch-mode power supplies for all on-board voltages. A
large number of congurable I/O‘s is provided via rugged
high-speed stacking connections. All this on a tiny footprint,
smaller than a credit card, at the most competitive price.
Key Features
Extended
device
life cycle
Rugged for
industrial
applications
§ FPGA: Kintex UltraScale KU35 or KU40 in A784 Package
60 Pin Razor Beam Connector
KINTEX
KU35
DDR4
I/O 56DIF 24
User I/O
Power Subsystem
DC/DC and LDO's
18
DDR4
GTH 3 LANES
PLL
SPI Flash
JTAG
Ÿ
I/O 16, DIF 8
Ÿ
GTCLK 2 Inputs
Ÿ
GTH 5 LANES
Ÿ
- Memory:
- 2 x 16-Bit DDR4
- SPI Boot Flash - 256 MByte max
Size: 40 x 50 mm, 3 mm mounting holes for skyline heat
spreader
B2B connectors: 3 x Razor beam, total 260 terminals
- User I/O: HR 12, HP 132
- Serial transceiver: GTH 8 lanes (all)
- GT clock inputs: 2
Clocking
- Si5338 - 4 output PLL, GT and PL Clocks
- 200 MHz LVDS oscillator
All power supplies on board, single supply operation
supported
TE0741 Series
Xilinx Kintex-7 T, Flash, 8 × Transceiver
Overview
integrating a Xilinx Kintex-7 T FPGA, 32 megabyte Flash
memory for conguration and operation, 8 transceivers, and
most competitive price.
Extended
device
life cycle
Key Features
Rugged for
industrial
applications
Ÿ Industrial-grade Xilinx Kintex-7 (70T, 160T, 325T
and 410T) SoM
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Recommended Software:
Kintex-7 XC7K70T-2CF, Kintex-7 XC7K160T-2CF: Xilinx
Vivado Webpack (free license)
25 MHz
Oscillator
Clock
Generator
JTAG
GTX transceiver
User I/O
Xilinx FPGA
Kintex-7 T
(70T, 160T,
325T, 410 T)
100 Pin
Ÿ
60 Pin
User I/O
Ÿ
GTX transceiver
Ÿ
100 Pin
Ÿ
- 2 x Transceiver clock (default 125 MHz)
- Fabric clock (default 200 MHz)
Plug-on module with 2 × 100-pin and 1 × 60-pin
144 FPGA I/O‘s (65 LVDS pairs possible)
available on board-to-board connectors
8 GTX (high-performance transceiver) lanes
- GTX (high-performance transceiver) clock input
User LEDs
User I/O
Kintex-7 XC7K325T-2CF, Kintex-7 XC7K410T-2CF: Xilinx
Vivado Design Suite
32 MByte
QSPI
Serial Flash
19
TE0600 (GigaBee) Series
Xilinx Spartan-6 LX, DDR3, Flash, GBit Ethernet
Overview
Trenz Electronic TE0600 are industrial-grade FPGA
modulesintegrating a Xilinx Spartan-6 LX FPGA, a gigabit
Ethernet transceiver (physical layer), two independent banks
of 1 GBit (128 MByte) DDR3 SDRAM each 16-Bit wide, 16
MByte Flashmemory for conguration and operation, and
competitive price.
Extended
device
life cycle
Key Features
Rugged for
industrial
applications
Ÿ Industrial-grade Xilinx Spartan-6 LX FPGA module
(LX45*, LX100 and LX150)
Ÿ 2 × 1 GBit DDR3 SDRAM, each 16-bit-wide
Ÿ 128 MBit (16 MByte) Quad-SPI Flash memory
(for conguration and operation) accessible through:
- B2B connector (SPI direct)
- FPGA
- JTAG port (SPI indirect)
- Gigabit Ethernet
Ÿ Gigabit Ethernet transceiver (PHY)
Ÿ FPGA conguration through:
- JTAG (B2B connector, 6-pin JTAG header)
- SPI Flash memory
128 MByte
DDR3 SDRAM
128 MByte
DDR3 SDRAM
Ÿ 125 MHz reference clock signal
Ÿ Plug-on module with two 100-pin high-speed
JTAG
Ÿ Up to 52 differential, up to 109 single-ended
(+ 1 dual-purpose) FPGA I/O pins available on B2B strips
100 Pin
User I/O
User I/O
10/100/1000
Ethernet PHY
Ÿ 1 user LED
Ÿ eFUSE bit-stream encryption (LX100 or larger)
Ÿ SHA-1 protection engine (option)
125 MHz clock
Xilinx FPGA
Spartan-6 LX
(LX45, LX100,
150 LX)
Quad SPI
Ÿ Footprint for single-ended custom oscillator (optional)
Assembly options for cost or performance optimization
available on request
16 MByte
dual/quad SPI
serial Flash
MAC
Address
EEPROM
20
EEPROM
(SHA-1)
Watchdog/
Supervisor
Custom (user)
clock
100 Pin
hermaphroditic stacking strips
4x5 Carrier Boards
Carrier Boards for all Trenz Electronic 7-Series Modules
TE0701
TE0703
application board
development board
Key Features
Key Features
Ÿ 4 x 5 module socket
Ÿ 4 x 5 module socket
Ÿ SD card connector (Zynq bootable SD)
Ÿ micro-SD Card connector (Zynq bootable SD)
Ÿ RJ45 GbE connector
Ÿ RJ45 GbE connector
Ÿ Pmod connectors (1 x PS MIO, 2 x PL IO)
Ÿ High performance Enpirion DC-DC converters
Ÿ ARM JTAG connector
Ÿ Barrel jack for 5 V power supply
Ÿ VITA 57.1 compliant FMC LPC connector
Ÿ Carrier controller CPLD (user programmable)
Ÿ High performance DC-DC converters
Ÿ USB host connector
Ÿ Barrel jack for 12 V power supply
Ÿ User push button and LEDs
Ÿ Carrier controller CPLD
Ÿ Mini-USB connector (USB JTAG and UART interface)
Ÿ Mini CameraLink connector
Ÿ 2x 96 pin 100 mil header/connector
Ÿ HDMI (ADV7511 transmitter)
Ÿ Maximum 168 I/O + I2C bus
Ÿ Micro USB (device, host/OTG modes)
Ÿ User push buttons and LEDs
Ÿ Mini USB connector (USB JTAG and UART interface)
Ÿ Battery holder for RTC backup voltage
21
Module series comparison table
GigaBee
TE0600
TE0630
TE0710
TE0711
TE0712
TE0715
GigaZee
TE0720
TE0722
„Dipforty"
Device list
45LX
100LX
150LX
45LX
75LX
100LX
150LX
35T
50T
75T
100T
35T
50T
75T
100T
35T
50T
75T
100T
200T
Z-7015
Z-7030
Z-7020
Z-7010
Form factor/size
[4 × 5]
[4 × 5]
[4 × 5]
[4 × 5]
[4 × 5]
[4 × 5]
1.8 x 5
Device family
4.05
4.75
5.1
Connectors
2 x Samtec
LSHM
2 × Hirose
DF17
2 × Samtec
LSHM
3 × Samtec
LSHM
3 × Samtec
LSHM
3 × Samtec
LSHM
3 x Samtec
LSHM
DIP40 + headers
Programmable
logic family
Spartan-6
Spartan-6
Artix-7
Artix-7
Artix-7
Z-7015: Artix-7
Z-7030: Kintex-7
Artix-7
Artix-7
MicroBlaze
MicroBlaze
MicroBlaze
MicroBlaze
MicroBlaze
2 x Cortex A9
2 x Cortex A9
2 × Cortex A9
2 x 128 DDR3
128 DDR3
512 DDR3
-
1024 DDR3
1024 DDR3
1024 DDR3
-
16
8
32
32
32
32
32
16
MAC
-
-
FTDI User
EEPROM
MAC
MAC
MAC
-
-
-
-
-
-
-
4 - 64 GByte
-
1 GBit
-
2 x 100 MBit
-
100 MBit
1 GBit
1 GBit
-
USB PHY
-
USB 2
-
USB 2
UART/FIFO
USB 2.0 OTG
USB 2.0 OTG
-
Total I/O
109
109
112
178
158
132 + 14 PS
152 + 14 PS
44
GBit transceivers
-
-
-
-
4 x GTP
Z-7015: 4 x GTP
Z-7030: 4 x GTX
-
-
Other features
-
-
-
-
RTC
Micro SD,
Ambient Light
Sensor
Processing
system
SDRAM capacity
[MByte] max
Flash [MByte]
EEPROM
eMMC
Ethernet PHY
22
1.8
Programmable Programmable
Clock
Clock Generator,
Generator
RTC
TE0725
Z-7010
15T
35T
50T
75T
100T
7.3
[7,3 ×3,5 ]
Shield
3.5
Arduino headers 2 x 50 pin headers
TE0728
Z-7010
Z-7020
(automotive)
TE0808
TE0729
TE0741
TE0782
Z-7020
70T
160T
325T
410T
Z-7035
Z-7045
Z-7100
8.5
5.2
[4 × 5]
[8.5 x 8.5]
[5.2 x 7.6]
8.5
7.6
pberry P
as
6
5.2
[8.56 x 5.65]
[6 x 6]
[5.2 x 7.6]
6
7.6
40 pin "HAT"
headers
3 x Samtec SEM
2 x Samtec BTE
3 × Samtec
LSHM
3 x Samtec QTH
„UltraSOM+“
ZU9EG (ZU4EV,
ZU5EV, ZU7EV,
ZU6EG,
ZU15EG)
TE0841
KU35
KU40
I
Arduino
[5.3 × 6.8]
TE0726
„ZynqBerry"
R
TE0723
„Arduzynq"
[4 x 5]
3 x Samtec ST5 3 x Samtec LSHM
Artix-7
Artix-7
Artix-7
Artix-7
Artix-7
Kintex-7
Kintex-7
UltraScale+
UltraScale
2 × Cortex A9
MicroBlaze
2 × Cortex A9
2 × Cortex A9
2 × Cortex A9
MicroBlaze
2 x Cortex A9
4 x Cortex A53 +
2 Cortex R5
MicroBlaze
512 DDR3L
32 HyperRAM
(optional)
512 DDR3L
512 DDR3
512 DDR3L
-
1024 DDR3
4096 DDR4,
Up to 64
HyperRAM
4096 DDR4
16
32
16
16
32
32
32
64
+ optional 256
XTRM Flash
32
-
16 KByte
USB LAN IC
EEPROM
8 KByte
3 x MAC
-
2 x MAC + 16
KByte
16 KByte
-
-
-
-
4 - 64 GByte
-
4-64 GByte
-
-
100 MBit
-
100 MBit
2 x 100 MBit
2 x 100 MBit,
1 GBit
-
2 x 1 GBit
-
1 GBit
MicroUSB OTG,
MicroUSB
FT2232
JTAG/UART/
FIFO
-
4 x USB 2.0
Host
-
USB 2.0 OTG
PHY
-
2 x USB 2.0
OTG
-
-
30
87
26
124 + 34 PS
136 + 14 PS
144
250 + 2 PS
144 + 65 PS
144
-
-
-
-
-
8 x GTX
16 x GTX
4 x GTR,
16 x GTH
8 x GTH
Raspberry Pi
Model 2
Form Factor,
DSI Display
optional 100/250
Micro SD,
Connector,CSI-2
MHz
onboard USB
Camera
POF Optical
JTAG + UART
Connector,
Module
Micro SD, 3.5
mm audio plug,
on-board USB
JTAG + UART
Automotive,
RTC,
CAN
Programmable
System Monitor,
RTC,
Programmable
Programmable Clock Generator,
Programmable
Cooling Solution
RTC,
Clock Generator
Clock Generator
Clock Generator
available
eMMC
23
Digilent Company Prole
Digilent Company Profile
Digilent Inc. is a world leader in academic and research technology solutions. Our aim is to help make more engineers
through making technology accessible to any audience.
Since our founding in 2000, by two engineering educators, Digilent has partnered with different leading semiconductor
companies including Xilinx, Microchip, Analog Devices and Texas Instruments to bring products that blend the world of
engineering education with engineering professionals. We offer resources such as: teaching material, sample labs,
shared curriculums, hardware at student affordable prices, student design contests, and an extensive partnership network
that caters to Universities. It's no wonder that our products can be found in over 1000 Universities in more than 70
countries!
Outside of our mission to make engineering accessible, we also provide OEM services Our expert team of engineers,
combined with our manufacturing services and worldwide distribution has made us an ideal OEM partner for several
leading technology providers such as Xlinx and Cypress. Our services extend to providing design expertise, using our
manufacturing and distribution channels, creating academic products for private label and even co-marketing a product
into the academic space. We want to enable our partners to be successful through well designed, high quality and well
manufactured hardware.
Digilent Activities
American Society of Engineering Education (ASEE)
The ASEE Annual Conference and Exposition is the only conference dedicated to all disciplines of engineering
education. It is committed to fostering the exchange of ideas, enhancing teaching methods and curriculum, and
providing prime networking opportunities for engineering and technology education stakeholders. Digilent partnered
with Dr. Kathleen Meehan from University of Glasgow to tell educators how to use Digilent Analog Discovery . We also
showcased the latest FPGA teaching solutions powered by Xilinx 7 seriesFPGA.
Electrical and Computer Engineering Department Head Conference (ECEDHA)
The ECEDHA Annual Conference is the only gathering of electrical and computer engineering department heads from
throughout the United States and Canada. The Conference Program presents a stellar lineup of featured speakers
drawn from industry and academia. Digilent is the platinum sponsor in ECEDHA 2015. We also held a panel
discussion about how makerspace help engineering education.
Embedded World
Digilent and its German distributor, Trenz Electronic, have participated Embedded World since 2009. We showcase
the latest technology every year.
Digilent Design Contest EU
The Digilent Design Contest provides an opportunity for students from Europe to use the latest technology in
electronics and digital design. It’s the ideal place for students to be able to indulge their imaginations and to develop
challenging projects. These projects are then shared with the community and then defended live in front of a jury
comprised of industry and academic representatives.
Various workshops in Europe
Digilent held various workshops with their distributors and technology partners in Europe.
www.trenz-electronic.de/digilent
24
Basys™3 Artix-7 FPGA Board
Overview
Key Features
The Basys3 is an entry-level FPGA board designed
exclusively for the Vivado Design Suite, featuring Xilinx Artix
7-FPGA architecture. Basys3 is the newest addition to the
popular Basys line of starter FPGA boards.
Ÿ Artix-7 FPGA : XC7A35T-1CPG236C
Now with the Basys3, Digilent gives users a better
representation of professional-level engineering by greatly
improving the feature sets. These improvements include:
More I/O:
Double the user interface switches, double the number of
onboard outputs, upgraded the number of external and
included for the first time on a Basys class device a USBUART bridge.
Modern Architecture =
Modern Programming Challenges:
Basys3 offers a substantial increase in hardware
capabilities. With the new Artix FPGA comes 15X the logic
cells (from 2,160 to 33,280) and the upgrade from multipliers
to true DSP slices. It also adds over 26X the amount of RAM.
Industry’s First SOC Strength Design Suite:
The most significant change to the Basys3 is the upgrade to
Xilinx Vivado Design Suite, the most modern design tool
chain used by professional engineers worldwide.
- 33,280 logic cells in 5200 slices
(each slice contains four 6-input LUTs and 8 flip-flops)
- 1,800 Kbits of fast block RAM
- Five clock management tiles, each with a phase-locked
loop (PLL)
- 90 DSP slices
- Internal clock speeds exceeding 450MHz
- On-chip analog-to-digital converter (XADC)
Ÿ 16 user switches
Ÿ 16 user LEDs
Ÿ 5 user pushbuttons
Ÿ 4-digit 7-segment display
Ÿ 4 Pmod connectors
Ÿ 3 Standard 12 pin Pmod
Ÿ 1 dual purpose XADC signal/ standard Pmod
Ÿ 12-bit VGA output
Ÿ USB-UART Bridge
Ÿ Serial Flash
Ÿ Digilent USB-JTAG port for FPGA programming and
communication
Ÿ USB HID Host for mice, keyboards and memory sticks
Related Items
Pmods
Textbook
www.trenz-electronic.de/basys3
25
Nexys Video
Key Features
Ÿ Artix-7™ XC7A200T
- 33,650 logic slices, each with four 6-input LUTs and
8 flip-flops
- 13 Mbits of fast block RAM
(3x more than the Nexys 4DDR)
- 10 clock management tiles, each with
phase-locked loop (PLL)
- 740 DSP slices
Ÿ On-chip analog-to-digital converter (XADC)
Ÿ Up to 3.75Gbps GTP transceivers
Ÿ 512MB 800MHz DDR3
Ÿ Dedicated onboard USB port for JTAG programming
and data transfers
Ÿ HDMI sink and HDMI source
Ÿ Mini DisplayPort source
Ÿ Audio codec w/ four 3.5mm jacks
Ÿ 10/100/1000 Ethernet PHY with included unique MAC
Overview
address
The Nexys Video is the latest addition to our Nexys line of
FPGA boards, and was designed with audio/video
enthusiasts in mind. A Mini DisplayPort source provides the
board with a uni-directional, high-bandwidth, low-latency
audio/video channel. Designed with high bandwidth
external memories, three high-speed digital video ports, and
a 24-bit audio codec, the Nexys Video is a potent platform for
A/V development. . The Artix-7™ XC7A200T FPGA is the
most powerful chip from Xilinx's Artix-7™ family.
Ÿ USB-UART bridge
Ÿ USB HID host for mice and keyboards
Ÿ Fully-populated 160-pin FMC LPC connector
Ÿ microSD card slot for nonvolatile storage
(card not included)
Ÿ User EEPROM
Ÿ 32Mbyte quad-SPI flash
Ÿ Four Pmod™ ports, Pmod for XADC signals
Ÿ Onboard user interfaces: 128x32 monochrome OLED
display, 5 user push buttons, 8 user switches, 8 user
LEDs
As a member of the Nexys family, the Nexys Video has been
designed with a high degree of communication, user and
expansion peripherals commonly found in industry. An FMC
connector and four Pmod connectors allow the addition of
Related Items
peripherals to further expand the functionality of the Nexys
Video.
The Nexys Video is compatible with both ISE and Vivado
toolchains. The free version of Vivado even includes the
ability to create MicroBlaze™ soft processor designs.
Pmods
www.trenz-electronic.de/nexysvideo
26
Nexys™4 DDR Artix-7 FPGA Board
Key Features
Ÿ XC7A100T-1CSG324C
- 15,850 logic slices, each with four 6-input LUTs and
8 flip-flops
- 4,860 Kbits of fast block RAM
- Six clock management tiles, each with
phase-locked loop (PLL)
- 240 DSP slices
- On-chip analog-to-digital converter (XADC)
Ÿ 16 user switches
Ÿ USB-UART Bridge
Ÿ 3-axis accelerometer
Ÿ 128MiB DDR2
Ÿ Pmod for XADC signals
Ÿ 6 user LEDs
Overview
Ÿ Two tri-color LEDs
Ÿ PWM audio output
The Nexys 4 DDR is a drop-in replacement for our cellular
RAM-based Nexys boards. The most notable improvement
is the replacement of the 16 MiB Cellular RAM with a 128 MiB
DDR2 SDRAM memory.
Ÿ Temperature sensor
Ÿ Serial Flash
communication
With its large, high-capacity FPGA and collection of USB,
Ÿ Two 4-digit 7-segment displays
Ethernet, and other ports, the Nexys 4 DDR can host designs
Ÿ Micro SD card connector
ranging from introductory combinational circuits to powerful
Ÿ PDM microphone
embedded processors.
Ÿ 10/100 Ethernet PHY
Several built-in peripherals, including an accelerometer, a
Ÿ Four Pmod ports
temperature sensor, MEMs digital microphone, speaker
amplifier and plenty of I/O devices allow the Nexys 4 DDR to
Application: MIPSFPGA microprocessor
be used for a wide range of designs without needing any
MIPSfpga is a configuration of the MIPS microAptiv family
found in many embedded devices, including the popular
PIC32MZ microcontroller from Microchip. With its long
heritage and excellent documentation MIPS is the preferred
choice of RISC architecture for many teachers around the
world. But to demonstrate key concepts in the past; teachers
had to settle for creating partial “MIPS-like” cores or using
unofficial copies of dubious heritage. Not now! MIPSfpga is
the real “industrial” RTL, non-obfuscated, and available
freely for academic use. The core comes with compatibility
to the Digilent Nexys4 DDR.
other components.
Digilent will provide a VHDL reference module that wraps the
complexity of a DDR2 controller.
You can find out the introduction at:
https://blog.digilentinc.com/index.php/new-productnexys4ddr/
Related Items
Pmods
Textbook
www.trenz-electronic.de/nexys4ddr
27
ZYBO Zynq™-7000
Development Board
Key Features
Ÿ ZYNQ XC7Z010-1CLG400C
- 650Mhz dual-core Cortex-A9 processor
- DDR3 memory controller with 8 DMA channels
- High-bandwith peripheral controllers: 1G Ethernet,
USB 2.0, SDIO
- d.Low-bandwidth peripheral controller: SPI, UART, I2C
- Reprogrammable logic equivalent to Artix-7 FPGA
- 28K logic cells
- 240KB Block RAM
- 80 DSP slices
- On-chip dual channel, 12-bit, 1 MSPS analog-to-digital
converter (XADC)
Ÿ 512MB x32 DDR3 w/ 1050Mbps bandwidth
Ÿ Dual-role (Source/Sink) HDMI port
Ÿ 6-bits per pixel VGA output port
Overview
Ÿ Trimode (1Gbit/100Mbit/10Mbit) Ethernet PHY
The ZYBO (Zynq Board) is a feature-rich, ready-to-use,
entry-level embedded software and digital circuit
development platform built around the smallest member of
the Xilinx Zynq-7000 family, the Z-7010. The Z-7010 is based
on the Xilinx All Programmable System-on-Chip
(AP SoC) architecture, which tightly integrates a dual-core
ARM Cortex-A9 processor with Xilinx 7-series Field
Programmable Gate Array (FPGA) logic. When coupled with
the rich set of multimedia and connectivity peripherals
available on the ZYBO, the Zynq Z-7010 can host a whole
system design. The on-board memories, video and audio
I/O, dual-role USB, Ethernet and SD slot will have your
design up-and-ready with no additional hardware needed.
Additionally, six Pmod connectors are available to put any
design on an easy growth path.
The ZYBO provides an ultra-low cost alternative to the
ZedBoard for designers that don't require the high-density
I/O of the FMC connector, but still wish to leverage the
massive processing power and extensibility of the Zynq AP
SoC architecture.
The ZYBO is compatible with Xilinx’s new high-performance
Vivado Design Suite as well as the ISE/EDK toolset. These
toolsets meld FPGA logic design with embedded ARM
software development into an easy to use, intuitive design
flow. They can be used for designing systems of any
complexity, from a complete operating system running
multiple server applications in tandem, down to a simple
bare-metal program that controls some LEDs. For systems
that require an operating system, Digilent provides an out-ofthe-box Linux solution specifically targeted to run on the
ZYBO, complete with documentation describing how best to
mold it to suite your purposes. These Xilinx tools and Linux
solution are all available to use at no additional cost with the
ZYBO.
Ÿ MicroSD slot (supports Linux file system)
Ÿ OTG USB 2.0 PHY (supports host and device)
Ÿ External EEPROM (programmed with 48-bit globally
unique EUI-48/64™ compatible identifier)
Ÿ Audio codec with headphone out, microphone and line
in jacks
Ÿ 128Mb Serial Flash w/ QSPI interface
Ÿ On-board JTAG programming and UART to USB
converter
Ÿ GPIO: 6 pushbuttons, 4 slide switches, 5 LEDs
Ÿ Six Pmod connectors (1 processor-dedicated, 1 dual
analog/digital)
Application: Zybot
Ÿ Description:
- Uses a lightweight Linux
distribution on the ZYBO
- Students will work with
specialized libraries while
learning about the hardware
& HDL requirements for
an embedded application
- Uses WiFi and a customized
server
- Provides many opportunities
for customization and
problem solving
Related Items
Pmods
www.trenz-electronic.de/zybo
28
Textbook
ZedBoard Zynq™-7000
Development Board
Overview
Key Features
ZedBoard is a development board for the Xilinx Zynq™-7000
All Programmable SoC (AP SoC). This board contains
everything necessary to create a Linux, Android, Windows®
or other OS/RTOS based design. Additionally, several
expansion connectors expose the processing system and
programmable logic I/Os for easy user access.
Ÿ Zynq-7000 AP SoC XC7Z020-CLG484
Users can apply Zedboard to a variety of applications
including video processing, motor control, software
acceleration, Linux/Android/RTOS development,
embedded ARM® processing and SoC prototyping
The Kit includes:
- ZedBoard 7020 baseboard
- 12 V AC/DC power supply
- 4 GB SD Card
- Micro-USB cable
- USB Adapter: Male Micro-B to Female Standard-A
Getting Started Guide
- Vivado® Design Suite with device-locked
Design Edition license
Ÿ Dual-core ARM Cortex A9
Ÿ Memory:
- 512 MB DDR3
- 256 Mb Quad-SPI Flash
- 4 GB SD card
Ÿ Onboard USB-JTAG Programming
Ÿ 10/100/1000 Ethernet
Ÿ USB OTG 2.0 and USB-UART
Ÿ PS & PL I/O expansion (FMC, Pmod™, XADC)
Ÿ Multiple displays (1080p HDMI, 8-bit VGA,
128 x 32 OLED)
Ÿ I2S Audio CODEC
Related Items
Pmods
FMC HDMI
Textbook
www.trenz-electronic.de/zedboard
29
Genesys 2 Kintex-7 FPGA Board
Overview
Key Features
The Digilent Genesys 2 board is an advanced, highperformance, ready-to-use digital circuit development
platform based on the powerful Kintex-7™ Field
Programmable Gate Array (FPGA) from Xilinx. With its
high-capacity, high-speed FPGA, fast external memories,
high-speed digital video ports, and wide expansions
options, the Genesys 2 is well suited for data and video
processing applications. Several built-in peripherals,
including Ethernet, audio and USB 2.0 allow a wide range
of additional applications. The fully-populated high-speed
FMC HPC connector opens the door to great expansion
possibilities.
Ÿ Kintex-7 FPGA : XC7K325T-2FFG900C
The Kintex-7 FPGA offers more capacity, higher
performance, and more resources than the Virtex-5 from
the first-generation Genesys
-
50,950 logic slices with 478,000 logic cells
34 Mbits Block RAM
On-chip analog-to-digital converter (XADC)
840 DSP Slices
Up to 12.5Gb/s GTP Transceiver
Ÿ 200MHz oscillator
Ÿ 1Gb DDR3 (32 bit)
Ÿ 256Mb QSPI Flash
Ÿ I2S Codec Audio Output
Ÿ 1 HDMI In and HDMI Out
Ÿ 1 Display port In and Display Port Out
Ÿ 1 128x32 OLED Display
Ÿ 1 FMC High Pin Count Connector
Ÿ 8 user LEDs
Ÿ 5 user pushbuttons
Ÿ microSD connector
Ÿ 4 Standard 12 pin Pmod connector
Related Items
Ÿ 1 dual purpose XADC signal/ standard Pmod
Ÿ USB-UART Bridge
Ÿ 10/100/1000 Ethernet PHY
communication
Ÿ USB OTG
Pmods
www.trenz-electronic.de/genesys2
30
Electronics Explorer Board
The EE board is also powered by the free
WaveForms™ software that makes it easy to acquire,
store, analyze, produce and reuse analog and digital signals
Overview
Key Features
The Digilent Electronics Explorer board includes all of the
1. Oscilloscope
Ÿ 4 channels, 40MSa/sec sampling frequency
Ÿ 70MHz analog input stage bandwidth
Ÿ 9MΩ /10pF input impedance
Ÿ +/-20V input range
Ÿ AC/DC coupling
Ÿ Input protection up to +-200V
test and measurement equipment needed to design and test
analog and digital circuits of all types. Built around a large
solderless breadboard, the EE board includes
oscilloscopes, waveform generators, power supplies,
voltmeters, reference voltage generators, and thirty-two
digital signals that can be configured as a logic analyzer,
pattern generator, or any one of several static digital I/O
devices. All of these instruments can be connected to
2. Arbitrary waveform generator
Ÿ 2 channels, 40MSa/sec
Ÿ 4 MHz bandwidth
Ÿ 10V amplitude with +/-10 V offset
circuits built on the solderless breadboards using simple
jumper wires.
The Electronics Board not only includes the standard
features found on Analog Discovery, but also have the
following advanced features.
3. Power supplies and voltmeters
Ÿ V+ and V- programmable voltage/current supplies of
up to +/-9V and up to 1.5 A
Ÿ fixed 5V/3.3V supply with up to 2 A
Ÿ 4 Voltmeters with +/-10V inputs
Ÿ Input impedance 1.2MΩ
Ÿ Voltmeter input protection up to +-200V
Ÿ Two reference voltages with +/-10V
4. Logic Analyzer
Ÿ 32 digital pins (shared with Digital Signal Generator
and Static I/O)
Ÿ 5. Digital signal generator
Ÿ 32 digital pins (shared with Logic Analyzer and Static
I/O)
www.trenz-electronic.de/eeboard
31
NETFPGA-SUME / NetFPGA 1G CML
Overview
Overview
The NetFPGA-SUME board is the ideal platform for highperformance and high-density networking design. A
collaborative effort between Digilent, the University of
Cambridge and Stanford University, the NetFPGA-SUME
has everything you need to conduct cutting edge
research and development of state-of-the-art networking
systems.
The NetFPGA-1G-CML is a versatile, network hardware
development platform featuring a Xilinx Kintex®-7
XC7K325T FPGA and includes four Ethernet interfaces
capable of negotiating up to 1 GB/s connections. The
NetFPGA-1G-CML is designed to support the Stanford
NetFPGA architecture. 512 MB of 800 MHz DDR3 can
support high-throughput packet buffering while 4.5 MB of
QDRII+ can maintain low-latency access to high demand
data, like routing tables. Rapid boot configuration is
supported by a 128 MB BPI Flash, which is also available for
non-volatile storage applications. The standard PCIe form
factor supports high speed x4 Gen 2 interfacing. The FMC
carrier connector provides a convenient expansion
interface for extending card functionality via Select I/O and
GTX serial interfaces. The FMC connector can support
SATA-II data rates for network storage applications and can
also be used to extend functionality via a wide variety of
other cards designed for communication, measurement,
and control.
The NetFPGA-SUME's main mission is to give students,
researchers and developers a state-of-the-art platform for
networking, whether it’s learning the fundamentals or
creating new hardware and software applications. This
board easily supports simultaneous wire-speed
processing on the four 10Gb/s Ethernet ports, and it can
manipulate and process data on-board, or stream it over
the 8x Gen.3 PCIe interface and the expansion interfaces.
The NetFPGA-SUME is an amazingly advanced board
that features one of the largest and most complex FPGA’s
ever produced, a Xilinx Virtex-7 690T supporting thirty
13.1 GHz GTH transceivers.
Key Features
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Xilinx Virtex-7 690T
Four SFP+ interface (4 RocketIO GTH transceivers)
supporting 10Gbps
PCI-E Gen3 x8 (8Gbps/lane)
QTH Connector (8 RocketIO GTH transceivers)
Two SATA-III ports
One HPC FMC Connector (10 RocketIO GTH
transceivers)
Three x36 72Mbits QDR II SRAM (CY7C25652KV18500BZC)
Two 4GB DDR3 SODIMM (MT8KTF51264Hz-1G9E1)
MicroUSB Connector for JTAG programming and
debugging (shared with UART interface)
Two 512Mbits Micron StrataFlash (PC28F512G18A)
Xilinx CPLD XC2C512 for FPGA configuration
User LEDs and Push Buttons
It is fully compatible with Xilinx Vivado and ISE Design
Suites as well as the Xilinx SDK for embedded software
design.
Key Features
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Related Items
Ÿ
Pmods
Xilinx Kintex®-7 XC7K325T-1FFG676 FPGA
Low-jitter 200 MHz oscillator
Four 10/100/1000 Ethernet PHYs with RGMII
X4 Gen 2 PCI Express
X16 4.5 MB QDRII+ static RAM (450 MHz)
X8 512 MB DDR3 dynamic RAM (800 MHz)
1 Gbit BPI Flash
SD card slot
32-bit PIC microcontroller
USB microcontroller
Real time clock
Crypto-authentication chip
High pin count FMC connector (VITA 57) with 100
Select-IO and 4 GTX serial pairs
Two Pmod™ connectors
Four on-board LEDs and four onboard generalpurpose buttons
Can be powered inside or outside a PC using a
standard ATX power supply with PCIe 6 pin or 6pin+2
connector.
FMC HDMI
www.trenz-electronic.de/netfpgasume
32
NI LabVIEW Home Edition
Overview
Education Kit
NI LabVIEW is a graphical programming platform used by
Physical Computing kit
millions of engineers and scientists for problem solving, data
Bring LabVIEW to the outside world with the Physical
acquisition and analysis, instrument control, automated
Computing Kit. No breadboarding, everything included,
testing and validation, prototyping, and more.
Now, there's LabVIEW Home, which has been targeted at
easy to do...
makers, allowing anyone to program visually, using icons
The Physical Computing Kit comes with:
1. LabVIEW Home Bundle
2. chipKIT WF32 microcontroller board
3. Handy project box w/ sticker sheet
4. USB cable
and wires to connect hardware and other applications in a
single environment.
What can you have in LabVIEW Home Bundle?
1. Unique graphical programming environment for
accelerated development
2. Extensive support for a wide range of measurement
hardware, I/O, and buses
3. Drag-and-drop interaction for quickly building graphical
user interfaces
4. Extensive signal processing, analysis, and math
functionality
5. Includes added functionality for text-based math and
control logic
We selected the WF32 because of its extensive onboard
capabilities. It has a WiFi module that lets you communicate
with a world of wireless devices, a Micro SD card slot for
reading & storing large amounts of data, and a USB 2.0
controller for power, configuration, and your own USB
applications. But that's just the beginning, because you'll
also have access to the WF32's 43 available I/O pins.
Connect whatever sensors, displays, controls, peripherals,
etc. you like and LabVIEW Home will be able to use them.
www.trenz-electronic.de/labview
33
NI academic products
NI academic product summary
Digilent is your source for products, parts, and accessories for National Instruments’ academic product line, including the
NI myRIO, myDAQ, and ELVIS. Digilent offers official NI products as well as Digilent-branded products that are fully
compatible with NI hardware. Contact us today to learn how Digilent and National Instruments help educators and
students learn the skills needed to Do Engineering.
From NI:
"At National Instruments, we believe that hands-on learning is what solidifies theoretical concepts and prepares students
for industry or advanced research. Skills learned in the classroom paired with platforms that scale to industry prepare
students to solve the grand challenges of tomorrow; at NI, we put this into practice by packaging industry-standard
technology into education form factors and working with partners to develop courseware. Learn how the same industryleading NI hardware and software technology used by more than 35,000 companies also improves education in more than
6,000 universities around the world.”
NI myRIO Accessory Board
myDigital Protoboard
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Power supply connector for stand-alone use
1260 tie point breadboard area
Seven-segment LED displays
4 push buttons, 4 slide switches
Discrete LEDs
Onboard 3.3/5VDC power regulator
Uses the Mini System Port (MSP) connector
myProto Protoboard
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Access all your myDAQ’s signals on a breadboard
3 onboard user LEDs
1 10K Potentiometer
2 Audio Jacks
External power connector for breadboard circuits
Power switches on all power supplies
Uses the Mini System Port (MSP) connector
Shield Adapter
Ÿ Uses the myRIO Expansion Port (MXP) connector
Ÿ Signal and power lines adapted to the standard Arduino™
Uno footprint.
Ÿ I2C is hardwired to A4 and A5 pins and adheres to the
revised Arduino Leonardo standard
Ÿ Standard 34-pin female breakout
Ÿ Switch allows users to select between UART and DIO pins
0 and 1
Ÿ No external power required for shields operating at 3.3V or
5V
www.trenz-electronic.de/nimyrio
34
NXT Sensor Adapter
Ÿ Signal and power lines adapted to the standard Arduino™ Uno
footprint.
Ÿ I2C is hardwired to A4 and A5 pins and adheres to the revised
Arduino Leonardo standard
Ÿ Standard 34-pin female breakout
Ÿ Switch allows users to select between UART and DIO pins 0 and 1
Ÿ No external power required for shields operating at 3.3V or 5V
Motor Adapter
Ÿ Can be congured to work with 2 DC motors, 1 stepper motor, or
2 RC servos
Ÿ Current control and sensing built in
Ÿ 6V-16V input voltage
Ÿ Over-current supply protection
Ÿ 34-pin female breakout allowing direct user access to signal pins
Ÿ External power supply connections
Ÿ Two 1.5A full h-bridge outputs
Ÿ Two on-board quadature encoders
Ÿ Internal PWM current control
Ÿ Power LED indicator
High Current Adapter
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Uses the myRIO Expansion Port (MXP) connector
Supports 3V - 16V output voltage (external power supply required)
4 Open drain outputs
Continuous current: 3.0A (25°C) / 2.2A (85°C)
Peak output current: 4.1A (t<5s)
4 Standard 3 terminal relay outputs
Common, Normally Closed, Normally Open
Relay output max switching voltage: 30V
Rated Current: 1A
34-pin female breakout allowing direct user access to
signal pins
MXP Breadboard & MXP Wirewrap
The MXP Breadboard provides a 300 tie breadboard & 50 tie bus
bar on an expansion card compatible with the myRIO Expansion
Port (MXP). The MXP Wirewrap provides a large 14x21 hole
prototyping area on an expansion card compatible with the myRIO
Expansion Port (MXP). Wirewrap functions as an I/O breakout, with
bus traces for GND, 3.3V, & 5V on either side of the prototyping
area.
www.trenz-electronic.de/nimyrio
35
Analog Discovery 2
Overview
Key Features
Digilent Analog Discovery 2 is a USB oscilloscope and
Ÿ Two-channel USB digital oscilloscope (1MΩ, ±25V,
visualize, generate, record, and control mixed-signal
differential, 14-bit, 100Msample/sec, 30MHz+
bandwidth - with the Analog Discovery BNC Adapter
Board)
circuits of all kinds. Developed in conjunction with Analog
Ÿ Two-channel arbitrary function generator (±5V, 14-bit,
multi-function instrument that allows users to measure,
Devices and supported by Xilinx University Program,
Analog Discovery 2 is small enough to fit in your pocket,
but powerful enough to replace a stack of lab equipment,
providing engineering students, hobbyists, and
electronics enthusiasts the freedom to work with analog
and digital circuits in virtually any environment, in or out of
the lab. The analog and digital inputs and outputs can be
100Msample/sec, 20MHz+ bandwidth - with the Analog
Discovery BNC Adapter Board)
Ÿ Stereo audio amplifier to drive external headphones or
speakers with replicated AWG signals
Ÿ 16-channel digital logic analyzer (3.3V CMOS,
100Msample/sec)
Ÿ 16-channel pattern generator (3.3V CMOS,
100Msample/sec)
Ÿ 16-channel virtual digital I/O including buttons, switches,
connected to a circuit using simple wire probes;
and LEDs – perfect for logic training applications
alternatively, the Analog Discovery BNC Adapter and BNC
Ÿ Two input/output digital trigger signals for linking
probes can be used to connect and utilize the inputs and
outputs. Driven by the free WaveForms 2015 (Mac, Linux
and Windows Compatible) software, Analog Discovery 2
can be configured to work as any one of several traditional
instruments..
multiple instruments (3.3V CMOS)
Ÿ Single channel voltmeter (AC, DC, ±25V)
Ÿ Network analyzer – Bode, Nyquist, Nichols transfer
diagrams of a circuit. Range: 1Hz to 10MHz
Ÿ Spectrum Analyzer – power spectrum and spectral
measurements (noise floor, SFDR, SNR, THD, etc.)
Ÿ Digital Bus Analyzers (SPI, I²C, UART, Parallel)
Ÿ Two programmable power supplies (0…+5V , 0…-5V).
www.trenz-electronic.de/analogdiscovery2
36
Analog Discovery 2
Oscilloscope
Ÿ Two fully differential channels; 14-bit converters; 100 MSPS
real-time sample rate
Ÿ 500uV to 5V/division; 1MΩ, 24pF inputs with 5MHz analog
bandwidth
Ÿ Input voltages up to ±25V on each input (±50V differential);
protected to ±50V
Ÿ Up to 16k samples/channel buffer length
Ÿ Advanced triggering modes (edge, pulse, transition types,
hysteresis, etc.)
Ÿ Trigger in/trigger out allows multiple instruments to be linked
Ÿ Cross-triggering with Logic Analyzer, Waveform Generator, Pattern
Generator or external trigger
Ÿ Mixed signal visualization
Ÿ Real-time FFTs, XY plots, Histograms and other functions always
available
Ÿ Multiple math channels support
complex functions
Ÿ All captured data files can be
exported in standard formats
Ÿ Scope configurations can be
saved, exported and imported16
user switches
Arbitrary Waveforms Generator
Ÿ Two channels; 14-bit converters; 100 MSPS real-time sample rate
Ÿ Single-ended waveforms with offset control and up to ±5 V
amplitude
Ÿ 5MHz analog bandwidth and up to 16k samples/channe
Ÿ Easily defined standard waveforms (sine, triangle, sawtooth, etc.)
Ÿ Easily defined sweeps,
envelopes, AM and
FM modulation
Ÿ User-defined arbitrary
waveforms can be defined
using standard tools
(e.g. Excel)
Logic Analyzer
Ÿ 16 signals shared between analyzer, pattern generator, and
discrete I/O
Ÿ 100 MSPS, with buffers supporting up to 16K transitions per pin
Ÿ LVCMOS logic level inputs Multiple trigger options including
pin change, bus pattern, etc.
Ÿ Trigger in/trigger out allows
multiple instruments to be linked
Ÿ Interpreter for SPI, I2C, UART,
Parallel bus
Digital Pattern Generator
Ÿ 16 signals shared between analyzer, pattern generator, and
discrete I/O
100 MSPS, with buffers supporting up to 16K transitions per pin
Algorithmic pattern generator (no memory buffers used)
Custom pattern editor supports up to 16K transitions per pin
3.3V outputs
Data file import/export using
standard formats
Ÿ Customized visualization
options for signals and busses
Ÿ
Ÿ
Ÿ
Ÿ
Ÿ
Spectrum Analyzer
Ÿ Performs FFT or CZT algorithm on analog input channels and
displays power spectrum
Ÿ Frequency range adjustments in center/span or start/stop modes
Ÿ Linear or logarithmic frequency scale
Ÿ Peak tracking option finds
peak power and adjusts display
to keep peak in center of display
Ÿ Vertical axis supports
voltage-peak, voltage-RMS,
dBV and dBu display options
Network Analyzer
Ÿ Waveform generator drives circuits with swept sine waves up to
10MHz
Ÿ Input waveforms settable from
1Hz to 10MHz, with 5 to 1000 steps
Ÿ Settable input amplitude and offset
Ÿ Analog input records response
at each frequency
Ÿ Response magnitude and phase
delay displayed in Bode,
Nichols, or Nyquist formats
Accessory
Analog Parts Kit
The Analog Parts Kit contains a large selection of components
perfect for creating a wide variety of useful circuits & devices.
Featuring Analog Devices components, the kit includes
transistors, resistors, capacitors, diodes, sensors, and variety of
useful ICs including Op Amps, convertors, and regulators. Finally,
the kit also comes with an assortment of lead
wires, a solderless breadboard, and a
screwdriver. A complete list and description
of components can be found on the
Digilent website.
Discovery BNC Adapter
The Discovery BNC adapter board is intended to be used with the
Analog Discovery™ tool to enable the use of standard BNC
terminated test leads and probes. It provides BNC terminations to
each of the two oscilloscope channels on the Analog Discovery.
Each channel of the oscilloscope can be selected as AC or DC
coupled by adjusting the jumper that is located behind that
channel’s BNC input connector. In addition, the two AWG
channels are also equipped with BNC terminations,
and each channel can have either the 50-ohm or
the 0-ohm termination selected. This enables the
user to match the Analog Discovery’s output
impedance with either standard 50-ohm test
leads or to be directly tied to the lead.
Power Brick
Every circuit needs a power supply, but simple, low cost, portable,
and reliable power sources can be hard to come by. The
PowerBRICK family provides the solution to all of those
requirements. There are four options to choose from: 12V, 9V, 5V,
or 3.3V. PowerBRICKS are designed to easily plug directly onto
your breadboard for simple, low profile integration. Powered by
5V from a standard USB, each PowerBRICK can provide up to
1.1W of power. PowerBRICKS can also be daisy-chained to
provide more than one +/- Vout pair, but total power output for the
entire chain should not exceed 2.2W.
Available in four output voltages:
Ÿ 12V (±100mA)
Ÿ 9V (±130mA)
Ÿ 5V (±200mA)
Ÿ 3.3V (±320mA)
Discovery Wire
www.trenz-electronic.de/analogdiscovery2
37
Pmods
Flexible peripheral modules for all your designs
Pmods™ are Digilent’s line of Peripheral Modules, small I/O interface boards that offer
an ideal way to extend the capabilities of programmable logic and embedded control
boards. They allow sensitive signal conditioning circuits and high-power drive circuits to
be placed where they are most effective - near sensors and actuators.
Pmods communicate with system boards using 6, 8 or 12-pin connectors that can carry
multiple digital control signals, including SPI and other serial protocols. Pmods allow for
more effective designs by routing analog signals and power supplies only where they
are needed, and away from digital controller boards.
Pmods work on system boards that adhere to the Pmod Standard. The Pmod Standard
lays out guidelines for form factor, communication protocols and access to a target
audience through reference manuals, code examples, user guides, and technical
support. You can learn more about the Pmod Standard by visiting its resource center.
8LD
Eight high bright LEDS driven by logic level inputs.
DA3
Single 16-bit, serial input, unbuered voltage output
digital-to-analog converter.
OD1
Provides four open drain outputs at up to 3A sent to
screw terminal connectors.
ACL
3-axis digital accelerometer with SPI and I²C
interfaces. Includes single/double tap & free-fall
detection.
DA4
Converts 8 12-bit channels of output from digital to
analog.
OLED
128 X 32 pixel OLED display w/ internal display
buer and a standard SPI interface.
ACL2
3-axis MEMS accelerometer with 12-bit resolution &
an SPI interface. Includes single/double tap & free-fall
detection.
DHB1
Dual H-Bridge motor driver - can drive 2 DC
motors or 1 stepper motor
PMON1
Digital power monitor capable of monitoring from
3.16V to 26V. Includes configurable alert and an I²C
interface.
AD1
Converts 2 analog signals to 12-bit digital at a
maximum sampling rate of one MSa/second.
DIP
DIP-to-Pmod adapter, allowing you to add a 2x6-pin
Pmod interface to your solderless breadboard
project.
PS2
Provides a PS/2 port for the connection of a mouse
or keyboard.
AD2
Converts up to 4 analog signals to 12-bit digital.
Features an I²C interface.
DPOT
Digital potentiometer w/ 256 resistance levels, screw
terminal & MTE connections, and 1 3-wire SPI
interface.
R2R
Resistor ladder D/A converter supporting 8-bit
conversion at up to 25 MHz.
AD5
Converts 4 dierential ( or 8 pseudo-dierential ) inputs
to 24-bit digital. Features an SPI interface.
ENC
Rotary Encoder Module with integral push-button.
Also includes a slide switch.
RF2
IEEE 802.15 wireless radio transciever that supports
ZigBee®, MiWi™, MiWi P2P and other protocols.
ALS
Ambient light sensor with 8-bit resolution and an SPI
interface.
GPS
GPS module featuring a GlobalTop Gms-u1LP
antenna module w/ low power consumption & UART
interface.
RS232
DB9 connector driven by logic level inputs translated
to RS232 voltage.
AMP2
Amplifies low power audio signals to drive a
monophonic
output.
GYRO
3-axis digital gyroscope with SPI & I²C interfaces.
Includes selectable resolutions and a built-in
temperature sensor.
RS485
Isolated high speed communication, Analog Devices
ADM2582E full/half duplex transceiver (16Mbps)
AMP3
HB3
2A H-bridge module ideal for driving small to
medium-sized DC motors using screw terminal
connectors.
RJ45
2W stereo power amplifier w/ digital input. Works
with I²C audio protocol or TDM. Can also operate
stand-alone.
Links to any AVR-based or FPGA-based Digilent board
via a standard RJ45 cable, ships as a pair of
male and female.
BB
Easy prototyping with a 266 tie point wire wrap area.
Ships with a 170 tie point bread board.
HB5
2A H-bridge module ideal for driving small to
medium-sized DC motors using 6-pin JST
connector.
RTCC
Real-time clock/calendar w/ battery backup,
128bytes EEPROM, 64 bytes SRAM, 2 alarms, & I²C
interface.
BT2
Bluetooth module using a simple UART interface.
Works in a wide range of modes.
I²S
Stereo audio output w/ stereo D/A converter and
supporting 16 to 24-bit audio at multiple sample
rates.
SD
Provides a convenient SD card interface for use with
Digilent system and microcontroller boards.
BTN
IA
Provides users with a way to measure the
electrical impedance of a circuit.
SF
Four debounced momentary pushbuttons.
Provides 16Mbit (2Mbyte) of flash ROM memory,
accessible via an SPI interface.
I/O port expander w/ an I²C interface, 16-element
FIFO, 19 I/Os, keypad decoding, PWM generator,
& more.
SF2
IOXP
Provides 128Mbit (16Mbyte) of serial PCM memory,
accessible via an SPI interface.
SSD
Two-digit high bright seven-segment display.
STEP
Stepper motor driver w/ a push-pull 4-channel
driver, driving up to 600 mA per channel. Host or
external power.
SWT
Four slide switches.
TC1
Temperature sensing Pmod with K-Type
Thermocouple module
TMP2
Temperature & thermostat control module with up
to 16-bit resolution and an I²C interface.
TMP3
Temperature sensor module w/ programmable 9 to
12-bit resolution, ±1°C accuracy & an I²C interface.
CDC1
Demonstrates capacitance-to-digital proximity
sensing through two capacitative “buttons”. Uses I²C
interface.
CLP
16x2 character LCD with optional backlight and 3.3V
or 5V operation.
CLS
16x2 character LCD display, controlled via UART, SPI
or TWI and a simple terminal-like interface.
JSTK
Two-axis resistive joystick with an integrated center
button and two additional push buttons.
KYPD
16-button keypad, numbered hexadecimally (0-9,
A-F).
LED
Four high bright LEDS driven by logic level inputs.
LS1
Infrared light sensor interface for connecting up to
four optical sensors
Translates logic signals between two user supplied
voltage levels.
CMPS
3-axis digital compass with ±8 gauss field detection
and an I²C interface.
CON1
Six screw terminal inputs.
(four for I/O, two for VCC & GND)
LVL
SHFT
CON3
Route 4 digital signals to four three-pin servo motor
connectors.
MAX- Single-transducer ultrasonic range finder. Can
measure distances over 20 feet with 1-inch
SONAR resolution.
CON4
Route two of four jumper-selectable digital signals to
two RCA connectors.
DA1
analog at up to one MSa/second.
DA2
analog at up to one MSa/second.
TPH
Six test points for in-line debugging between a system
board and a Pmod.
MIC3
Small MEMS microphone module with digital interface,
improvement of PmodMIC
TPH2
Twelve test points for in-line debugging between a
system board and a Pmod.
NIC100
IEEE 802.3 Ethernet controller with an SPI interface.
Oers MAC support and 10/100 Mbs operation.
USBUART USB to serial UART interface with a micro USB
OC1
Provides four open collector outputs at up to 200
mA sent to a 6-pin header connector.
connector.
WIFI
Wi-Fi radio transceiver module, adds
Wi-Fi communication to any Digilent system board.
Key: Input Output Communication Connector Power Misc.
www.trenz-electronic.de/pmods
38
Programming Solutions
Digilent produces a variety of high-speed JTAG and SPI USB2 programming solutions that
work seamlessly with all Xilinx tools. Our free Adept software allows custom applications
to drive JTAG and SPI operations, and to exchange data with target systems.
JTAG-SMT2-NC
JTAG-SMT2
JTAG-HS3
JTAG-HS2
Max Speed
30 Mhz
30 Mhz
30 Mhz
30 Mhz
Voltage Range
1.8 - 5 V
1.8 - 5 V
1.8 - 5 V
1.5 - 5 V
Xilinx Native
Support
ISE 14.1+
Vivado 2013.1+
ISE 14.1+
Vivado 2013.1+
ISE 14.1+
Vivado 2013.1+
SE 13.2+
Vivado 2012.1+
Xilinx Plug-in
Support
ISE 13.1+
ISE 13.1+
SE 12.1+
SE 12.1+
Digilent Adept™
Support
ü
ü
ü
ü
PC Interface
USB
USB
USB
USB
û
ü
ü
ü
13-pad SMT
11-pad SMT
14-pin
6-pin, 14-pin
4-Wire JTAG
ü
ü
ü
ü
2-Wire JTAG
ü
ü
û
ü
ZYNQ-7000
PS_SRST Support
ü
ü
ü
û
SPI Support
ü
ü
û
ü
Onboard USB
Connector
Target Board
Connector Interface
www.trenz-electronic.de/programmingsolutions
39
40
41
Boards and kits
Xilinx development boards and kits provide an out-of-the box design solution to accelerate
development time and time-to-market. Xilinx offers kits complete with evaluation boards, the Vivado
Design Suite tools, IP cores, reference designs and FPGA Mezzanine Card (FMC) support
– so application development begins immediately out of the box.
The Vivado Design Suite delivers a SoC-strength, IP-centric and system-centric, next generation
development environment that has been built from the ground up to address the productivity
bottlenecks in system-level integration and implementation.
Xilinx Artix-7 FPGA AC701 Evaluation Kit
It features the leading system performance per watt Artix-7 family to get
you quickly prototyping for your cost sensitive applications. This
includes all the basic components of hardware, design tools, IP, and
pre-veried reference designs. This also features a targeted reference
design enabling high-performance serial connectivity and advanced
memory interfacing equipped with a full license for the Northwest Logic
DMA engine.
Xilinx Kintex UltraScale FPGA KCU105 Evaluation Kit
This is the perfect development environment for evaluating the cutting
edge Kintex UltraScale All Programmable FPGAs. The Kintex
UltraScale family delivers ASIC-class system-level performance, clock
management, and power management for next generation systems at
the right balance of price, performance and power. This kit is ideal for
those prototyping for medium- to high-volume applications, such as
Data Center, wireless infrastructure, and other DSP-intensive
applications.
Xilinx Virtex UltraScale FPGA VCU108 Evaluation Kit
This kit is the perfect development environment for evaluating the
unprecedented levels of performance, system integration and
bandwidth provided by Virtex UltraScale devices. This kit provides an
ideal platform for prototyping systems that require massive data ow
and packet processing such as 400+ Gbps systems, large-scale
emulation and high performance computing.
Xilinx Zynq-7000 All Programmable SoC ZC706
Evaluation Kit
It includes all the basic components of hardware, design tools, IP, and
pre-veried reference designs including a targeted design, enabling a
complete embedded processing platform and transceiver based
designs including PCIe. The included pre-veried reference designs
and industry-standard FPGA Mezzanine Connectors (FMC) allow
scaling and customization with daughter cards.
There are other Xilinx boards available on request, please ask for
a quote at sales@trenz.biz
42
43
44
45
Trenz Electronic GmbH is a global authorized distributor of Red Pitaya products.
www.trenz-electronic.de/redpitaya
About Red Pitaya
Red Pitaya is a spin-off company from Instrumentation Technologies, a leader in designing and building
high performance measurement instruments for one of the most complex machines on earth - particle
accelerators.
They believe in empowering individuals to conduct their own education, discover their own inspiration,
and share their ideas with other passionate people.
Red Pitaya Products
Red Pitaya is an open source project developed around a reconfigurable measurement instrument in size
of a credit card. It can replace many expensive laboratory measurement and control instruments. The
users can start using the applications available within the Bazaar free of charge marketplace. This can be
achieved with a single click. At the same time they can view and modify the published source code in
order to develop new applications and share their results with the community.
The Red Pitaya unit is a network attached device based on Linux operating system. It includes Radio
Frequency signal acquisition and generation technologies, FPGA, Digital Signal Processing and CPU
processing. Red Pitaya enables everyone to start using technologies, yesterday available only to advanced
research laboratories and industry.
All Red Pitaya products have one year return to manufacturer warranty period and are manufactured
according to ISO 9001registered quality scheme. Red Pitaya products are CE, MET, FCC and RoHS
compliant.
Red Pitaya Board V1.1
•
•
•
•
•
•
•
•
•
•
•
•
Xilinx Zynq 7010 SoC
Dual core ARM Cortex A9+ FPGA
DDR3 RAM 512MB (4Gb)
microSD up to 32Gb
1000Base-T Ethernet connection
USB 2.0
Console connection: micro USB
Power consumption: 5V, 2A max
Fast Analog Inputs and outputs: 125 MS/s, 14 bit
Slow analog inputs: 100 kS/s, 12 bit
Operating system: Linux
Default functionality: Multi-instrument
Key Features
• High performance hardware at a surprising price tag
• Replaces most essential instruments like Oscilloscope,
Spectrum analyser, Signal generator, LCR meter
• LAN or wireless access from any WEB browser via
tablet or a PC regardless of the OS (MAC, Linux,
Windows, Android, iOS)
• LabView and MATLAB® interface
• Possibility to make your own application and share it
with others
• Open source software
46
Trenz Electronic GmbH is a global authorized distributor of Red Pitaya products.
www.trenz-electronic.de/redpitaya
Red Pitaya Starter Kit
Red Pitaya Diagnostic Kit
The Starter Kit consists of a
The Diagnostic Kit consists of a
Red Pitaya V1.1 board,
Red Pitaya V1.1 board,
a micro USB power supply adaptor
2 Pintek CP-2100 oscilloscope probes,
and a 4GB microSD card.
2 adaptors SMA(M) to BNC(F),
a micro USB power supply adaptor and
a 4GB microSD card.
Red Pitaya Sensor Extension Module and Enclosure
Red Pitaya extension module is an add on board
Transparent enclosure accurately
that can be plugged in on top of the Red Pitaya board
fitting for the Red Pitaya 1.1 Board
to expand its uses and capabilities.
Red Pitaya
Tržaška cesta 25
SI - 1000 Ljubljana
www.redpitaya.com
sales@redpitaya.com
redpitayaopen
red%20pitaya
red_pitaya
red-pitaya
47
48
49
50
51
KINTEX UltraSCALE : 8K4K image evaluation platform
Part Number : TB-KU-060-ACDC8K / TB-KU-075-ACDC8K
The latest platform accelerate development super-high denition 8K image processing.
4 20nm KINTEX UltraSCALE
XCKU060-2FFVA1517 (Mar. 2015)
XCKU075-2FFVA1517 (Q3. 2015)
4 2x DDR4 SDRAM(2,400Mbps)64bit enables
wide band data buffer
4 Provide the extensibility with GTH transceiver
- 7xFMC connectors
(see the example table below)
- On board 4x SFP+ socket, QSFP
for Video stream through Ethernet
Zynq-7000 All Programmable SoC
2ch Giga-Bit Ethernet embedded module
Part Number :TB-7Z-IAE
Supporting smoothly moving to mass production for smart function products.
4 Small form factor with Zynq® -7000 All
Programmable SoC hi-performance embedded
model
4 Multiple network protocol can be support by 2ch
Giga-bit Ethernet with programmable logic.
4 Reduce to design risk of Zynq and power circuit.
4 Easy to use for small quantity products.
4 Development kit is available for multiple application
development.
www.trenz-electronic.de/inrevium
52
TB-A7-200T-IMG
FPAG evaluation board with the Xilinx Artix-7 FPGA.
4 Xilinx® Artix®-7 FPGA device: XCYA200T-2FFG1156
4 Two VITA-57.1 high-pin count FPGA mezzanine cards
(FMC) connectors with many I/O and 8 multi-gigabit
transceivers (MGT’s)
4 2GB DDR3 SO-DIMM module
4 100/1000MBaseT Ethernet RJ45-style port
4 Digital Audio S/PDIF coaxial TX and RX jacks
4 Micro-USB port for FPGA conguration
4 Micro-USB UART port
4 4 general purpose pushbuttons and LEDs,
8-positions general purpose DIP switches
4 On-board programmable clock generator
4 User clock input MMCX jacks
4 256Mb QSPI Flash for conguration and user data
4 Two Digilent Pmod 12-pin peripheral sockets
53
Option Card FMC HPC（High Pin Count) & LPC（Low Pin Count)
12G SD SDI Card
3G/HD/SD SDI Card
HDMI1.4 Card
HDMI 2.0 Card
TB-FMCH-12GSDI
TB-FMCH-3GSDI2A
TB-FMCH-HDMI2
TB-FMCH-HDMI4K
Ÿ 75Ohm HD-BNC,
1ch IN, 1ch OUT
Ÿ 3ch Bi-direction
Ÿ Expansion connector for
additional TB-FMCH12GSDI
Ÿ Analog B.B SYNC input
Ÿ Supports FMC 1.8V IO
Ÿ Attached D-BNC-BNC
convert cable
Ÿ 148.5MHz,
148.35165MHz clock
Ÿ 3G/HD/SD SDI 2ch IN,
2ch OUT
Ÿ 2ch Bi-direction
Ÿ Expansion connector for
additional TB-FMCH3GSDI2A
Ÿ Analog B.B SYNC input
Ÿ Supports FMC 1.8V IO
Ÿ Attached DIN-BNC
convert cable
Ÿ provides HDMI encoder and
decoder functions
Ÿ each board has 2 independent
receivers/transmitters
Ÿ designed for high resolution
support
Ÿ
Ÿ
Ÿ
Ÿ
2x HDMI connectors
1x HDMI4K Source
1x HDMI4K Sink
Designed for electrical
compatibility with most carrier
cards
Ÿ Proven operation with inrevium
ACDC and KC705
Ÿ Stackable FMC design
supports additional TB-FMCHHDMI4K
1000Base-T Ethernet Card
LVDS Card
Pin Header Card
TB-FMCL-GLAN-B
TB-FMCL-LVDS
TB-FMCL-PH
Ÿ 30pin, pin header x3
Ÿ Each pin header connect
24 signals
Ÿ For developing LVDS
Ÿ For LAN
Communication
Ÿ 1000BASE-T
PHY(Marvell)：
88E1111-B2-BAB1C000
interface
Ÿ LVDS Tx/Rx Loopback
Design (VerilogHDL）
FPGA Mezzanine Card (FMC) Standard
FMC is VITA 57 standard, provides a specification describing an I/O mezzanine module with connection to an FPGA or other device with reconfigurable I/O capability.
Connector
Number of Pins
User I/O (SERDES I/O)
High Pin Count (HPC)
400 pin
168 pin (10 channels)
Low Pin Count (LPC)
160 pin
72 pin (1 channel)
54
Trenz Electronic GmbH is an authorized distributor of SoC-e products
www.trenz-electronic.de/soc-e
About SoC-e:
System-on-Chip engineering (SoC-e) develops IP cores and electronic modules for Reliable Ethernet Networks and highaccuracy synchronization systems.
SoC-e products have presence in the Energy Market (Substation Automation, and Smart Grids), in the Aerospace and
Industry Sectors.
SoC-e COTS products are complemented with SoC-e engineering services, providing customization for specic FPGA IP
Cores, System-on-Programmable-Chips and board designs.
SoC-e is a private owned company located in Bilbao, Spain.
For more information, please visit our website at www.soc-e.com
SMARTzynq module
SMARTZynq module is a pluggable module designed to enable easy
integration of Ethernet Industrial Networks in equipments for Electric,
Transportation, Aerospace and Industrial Automation sectors.
This powerful module allows the implementation of custom routers,
switches or end-equipments with powerful networking capabilities. Network
frame processing can be performed by hardware using specic IPs.
SMARTZynq module is based on a Zynq-7000 device from Xilinx.
This device includes an ARMv9 dual core microprocessor attached to the
Programmable Logic in order that software stacks can co-work with
hardware frame processing.
With its 5 Ethernet Phyters (One 10/100/1000TX for conguration and
management plus four 10/100/1000TX or 1000FX), it may be used in a wide
range of products and applications. It is a simple way to introduce
redundancy capacities.
SMARTzynq carrier
SMARTZynq brick
SMARTZynq Carrier is 160x100mm (Eurocard) size and
SMARTzynq brick is a bundle consisting of a SMARTZynq
includes 4x SFP cages for 1GE Fiber or 10/100/1GE copper
module, a SMARTZynq carrier board, a power supply and
modules, one USB B connector, one Gigabit Ethernet
an USB cable. It offers 4 SFP cages that can be
connector and two PMOD connectors. Customers can use
connected to the PL section of the Zynq for tri-speed
this carrier as a reference to design their own one or to
operation and 1 RJ45 connector that is attached directly
include SMARTzynq in their equipments.
to the PS section. SFP cages support 10/100/1GE copper
and 1 GE Optical Fiber SFPs.
55
56
57
Ndigo Crate-5 / PCIe over cable
With the Ndigo Crate it is possible to use up to 5 PCIe boards and 2 PCI boards
with a PC. The connection of the external chassis to the PC happens over PCIe2
x16 for a full duplex bandwidth of 2x 8GByte/s.
The enclosure was specically designed to operate multiple synchronized
cronologic digitizer boards to create a high speed data acquisition system. It can
also be used to house other DAQ cards, GPUs for high performance computing,
storage adapters or networking equipment.
The extension is fully transparent. The operating system can't distinguish between
boards in the PCIe expansion box and boards inside the PC itself. No drivers are
required.
The slot covers are on the front side of the enclosure to easily see status
information and plug in cables during operation.
The crate is delivered as a set with cable and PC link board.
Facts
Connection to host:
Bandwidth to host:
PCIe3 x 16 Slots with 8 Lanes:
PCIe3 x 16 Slots with 4 Lanes:
PCI Slots 5 V, 32 Bit, 33 Mhz:
58
PCIe2 x 16
8 GByte/s
2
3
2
59
Distributor list
Canada
Joral Technologies Inc
4322 Donnelly Road
K0G 1J0 Ottawa, Ontario
Canada
Phone: +1 (877)-380-3366
Fax: +1 (877)-838-7712
Email: sales@joral.ca
China
Future Linking Solution Tech Co. Ltd
Unit 01 7/F, Bright Way Tower
33 Mong Kok Rd, KL
Hong Kong
Phone: +86-755-82914675
Fax: +86-755-82971302
Web: www.fulso.com
Email: liu@fulso.com
Czech Republic
DFC Design, s.r.o.
Strmá11B
61600 Brno
Czech Republic
Phone: +420 511 112 863
Fax: +420 549 241 114
Web: www.dfcdesign.cz
Email: info@dfcdesign.cz
France
Lextronic
36/40 Rue du Général de Gaulle
94510 La Queue en Brie
France
Phone: +33(0)1.45.76.83.88
Fax: +33 (0)1.45.76.81.41
Web: www.lextronic.fr
Email: lextronic@lextronic.fr
Hungary
Chipcad
Tűzoltó u. 31. (IX. kerület)
1094 Budapest
Hungary
Phone: +36-1-231-7000
Fax: +36-1-231-7011
Web: www.chipcad.hu
Email: SzFarkas@chipcad.hu
Italy
Mirifica s.r.l.
Piazza 11 Febbraio, 7
29012 Caorso PC
Italy
Phone: +39 0200611003
Fax: +39 02700446883
Web: www.mirifica.it
Email: store@mirifica.it
Japan
Tokushu Denshi Kairo Inc.
84-403 Kanda Sakuma Gashi
101-0026 Chiyoda
Japan
Phone: +81-3-3865-5381
Fax: +81-3-3865-5382
Web: www.tokudenkairo.co.jp
Email: tonaki(at)tokudenkairo.co.jp
Slovakia
DFC Design, s.r.o.
Strmá 11B
61600 Brno
Czech Republic
Phone: +420 511 112 863
Fax: +420 549 241 114
Web: www.dfcdesign.cz
Email: info@dfcdesign.cz
Spain
Taiwan
Future Linking Solution Tech Co. Ltd
Unit 01 7/F, Bright Way Tower
33 Mong Kok Rd, KL
Hong Kong
Phone: +86-755-82914675
Fax: +86-755-82971302
Web: www.fulso.com
Email: liu@fulso.com
Turkey
Same Elektronik San. Ve Tic. A.S.
Mebusevleri Mah. De Gol Cad.
Meçhul Asker Sok. 18/7
06580 Cankaya - Ankara
Turkey
Phone +90 312 212 2211
Fax: +90 312 212 2275
Web: www.sameas.com.tr
Email: same@sameas.com.tr
UK
Sundance Multiprocessor
Technology Ltd.
Chiltern House
Waterside
Chesham
Buckinghamshire HP5 1PS
United Kingdom
Phone: +44 1494 793167
Fax: +44 1494 793168
Web: www.sundance.com
Email: trenz@sundance.com
USA
Concurrent EDA LLC
5001 Baum Blvd Ste 640
Pittsburgh, PA 15213
United States of America
Phone: +1 412-687-8800
Web: www.concurrenteda.com
Email: trenz@concurrenteda.com
kran77 / fotolia.com
Cyberall Group
Aureli Capmany 2, Local 7
08195 Sant Cugat, Barcelona
Spain
Phone: +34 93 675 64 04
Fax: +34 93 975 68 44
Web: www.cyberallgroup.com
Email: sales@cyberallgroup.com
facebook.com/trenzelectronicgmbh
plus.google.com/+trenzelektronik
twitter.com/TrenzElectronic
60

TRENZ ELECTRONIC

Transcription

Similar documents

www.globo.com.pl OPTICUM HD 9600 PRIMA id: O9600PRIMA

EMUKEY Product Sheet

What does it measure? The Visioscan® VC 98 USB is a special UVA

portable usb dj mixer + scratch controll er + dj software

FPGA Design Tips

3.5" SATA to USB 3.0 External Hard Drive Enclosure

SC-2300 spec

Solidyne - Jackson Systems

Charging your PowerSLIMTM 9.0 - eshop x

ALXW1730-i7-A1_DataS..