Dohrmann Applicators

Transcription

Dohrmann
Applicators
by:
DE-1000
Dohrmann Enterprises, Inc.
DE-25
AUGRA METER
Dohrmann
DE
Enterprises, Inc.
for more information
316 33rd Ave South | Waite Park, MN 56387
(320) 252-8999 www.DohrmannEnterprises.com
Applicator selection
SELF PROPELLED FORAGE HARVESTERS
For Liquid Concentrate Inoculants: DE-1000 Dohrect Enject (Page 3)
Conventional Application: DE-100 or DE-55 (Page 4) & SP-1 Control (Page 11)
PULL-TYPE FORAGE HARVESTERS
For Liquid Concentrate Inoculants: DE-1000 Dohrect Enject & CM-2 Chopper Mount (Page 3)
Conventional Application: DE-45 (Page 4) or DE-25 (Page 5) & CM-1 Chopper Mount (Page 8)
Optional Equipment: SP-1 Control
LARGE SQUARE BALERS
DE-100 or DE-55 (Page 4), LS-1 Mounting Kit (Page 8) & SP-1 Control (Page 11)
Optional Equipment: Flowmeter (Page 10) & Moisture Tester (Page 9)
ROUND BALERS
DE-25 (Page 5) & SP-1 Control (Page 11)
John Deere: Add JDRD Mounting Kit (Page 8)
Non-John Deere Round Balers: Add 2 #184 Round Baler Nozzle Brackets
NH BR770 & BR780 can use DE-55 (Page 4)
Optional Equipment: Flowmeter (Page 10) & Moisture Tester (Page 9)
SMALL SQUARE BALERS
DE-25 or DE-6 (Page 5)
Optional Equipment: SP-1 Control (Page 11), Flowmeter (Page 10) & Moisture Tester (Page 9)
STATIONARY AND SEMI-STATIONARY APPLICATION
DE-8 (12 Volt, Page 5)
EXISTING TANK OR BARREL MOUNT
DE-9 (Page 4) or DE-7 (Page 5)
Optional Equipment: SP-1 Control (Page 11) & Flowmeter (Page 10)
For Baled Hay Only: Moisture Tester (Page 9)
GRANULAR APPLICATION
AM-1 Augra Meter (Page 6)
For Self Propelled Forage Harvesters & Balers Add: AM-1BK Blower Kit (Page 6)
For Round & Large Square Balers Add: AM-1BKD Blower Kit Diffuser (Page 7)
NON MECHANICAL (GRAVITY) APPLICATION
DE-5 Gravity Flow (Page 7)
Transfer Pumps: Page 7
Mounting Options: Page 8
Moisture Testers: Page 9
Flowmeters: Page 10
Control Options: Page 11
2
(320) 252-8999
Dohrect Enject System
{
U.S. Patent NO. 6,443,369
Canada Patent NO. 2,411,690
Introduced in 2001, this is the original “Low Volume, Long Distance Applicator” designed for
applying inoculants in a liquid concentrate form and is also the only inoculant system with an
insulated tank. This unit was designed for use on Self Propelled Forage Harvesters and may also
be used on Pull-Type Forage Harvesters with our CM-2 Chopper Mount.
DE-1000
FM-1000
{
for Liquid Concentrate
DE-1000
Low Application Rate
• Mix up to 1000 treatable ton per fill in 10 gallon insulated tank
• Apply at rates as low as 1.28 ounces per ton
(maximum 5 tons per minute)
10 Gallon Insulated Tank
• Keeps bacteria cool and healthy for prolonged storage and during
high temperature harvest
SP-2 Variable Rate Control – Included – For DE-1000 Only
• Allows the operator to make “on the fly” rate adjustments
from the cab
FM-1000 Flowmeter – Included – For DE-1000 Only
• Gives the operator an indication of the product flow rate through
the system – greatly simplifies system calibration
Easy to Clean
• Insulated tank is easily removed and has a full diameter lid
• Flush System Included (Pump and Lines)
No Nozzle or Orifice to plug
Compact Size
• Dimensions: 20”L X 19” W X 24” H
FM-1000 Flowmeter
DE-1000
with CM-2
(Included with DE-1000)
This flowmeter is designed exclusively for the DE-1000 to make calibration
simple and easy. This unit reads in Tons per Minute (100 ton per gallon rate)
on one side and ounces per minute on the other. Simply float the calibration
ball to your desired application rate and calibration is complete. Mounting is
done with a swivel bracket that can be mounted to a flat surface or can be
mounted to a railing using the included U-Bolt.
CM-2 Chopper Mount
The CM-2 is used for mounting the DE-1000 Dohrect Enject System on
pull-type forage harvesters
www.DohrmannEnterprises.com
3
Ag-Serv applicators
DE-100
DE-100
Dimensions: Tank & Frame: 57”L X 24”W X 31H
Pump Unit: 15”H X 15”W X 6.5”D
Ideal for: Self Propelled Forage Harvesters • Large Square Balers (require LS-1 & SP-1)
• 100 Gallon Tank and Frame
• 3.0 GPM Self Priming Pump
• Self-Fill System
• 3 Nozzle Assembly with 20’ of hose
• Pressure Regulation System with Stainless Steel Gauge
• 30’ Power Cord
• on-off switch
• In-Line Gauge
Recommended Options:
SP-1 Speed Control (page 11)
DigiFlow Digital Flowmeter (page 10)
Moisture Tester-for use with baled hay (page 9)
DE-55
DE-55
Dimensions: Tank & Frame: 38”L X 23”W X 32”H
Ideal for: Self Propelled Forage Harvesters • Large Square Balers (require LS-1 & SP-1)
• on-off switch
• In-Line Gauge
DE-45
DE-45
Dimensions: Tank & Frame: 43”L X 22”W X 22”H
Ideal for: Small Square Balers • Pull-Type Forage Harvesters (requires CM-1)
• on-off switch
• In-Line Gauge
DE-9
DE-9
Same as DE-100, DE-55 & DE-45 Pump Unit without Tank and Frame
Use with an existing tank or draw from a barrel mount
• on-off switch
• In-Line Gauge
4
(320) 252-8999
DE-25
Dimensions:
33”L X 19.5” W X 22” H
DE-25
Ideal for:
Small Square Balers • Round Balers • Pull-Type Forage Harvesters (requires CM-1)
• 25 Gallon Tank with flat surface mounting brackets
• on-off switch
JDRD Mounting Kit for John Deere Round Balers (page 8)
DE-6
DE-6
Dimensions:
18”L X 15” W X 22” H
Ideal for: Small Square Balers • Forage Blowers & Baggers
• For use with 5-6 gallon pail (pail not included)
• on-off switch
DE-7
DE-7
Use with an existing tank or a barrel mount, not recommended for
Large Square Balers
• on-off switch
DE-8
DE-8
Ideal for:
Forage Blowers & Baggers (stationary applications)
• Hangs on the side of a 55 gallon drum (drum not included)
• Single Nozzle Assembly (4-72 oz. per minute) with 20’ of hose
• 15’ Power Cord with Battery Clips
• on-off switch mounted on applicator
5
Granular applicators
AM-1
AM-1____ Augra Meter
AM-1 Augra Meter
Dimensions:
23.5”L X 14.5” W X 28” H
A proven concept designed for easy, precise metering of granular products.
The AM-1 series Augra Meters are 12 volt systems available in 5 different
flow ranges. (see chart)
1.6 Cubic Foot Poly Hopper
• 12” Rain Tight Lid
• Easy to Fill
Model #
RPM
Low /
Minute
High /
Minute
AM-1UHV
25
1lb.
7.9
AM-1HV
17
.9
5.75
2” High Density Poly Auger
AM-1MV
12
.7
3.75
12 Volt Direct Drive Gear Head Motor
AM-1LV
8.5
.5
2.7
AM-1ULV
4.5
.3
1.5
SP-1s Control – Included
(See page 11 for details)
• Enables user to control the auger
speed to achieve the desired flow rate
• Can be wired on the Augra Meter or
elsewhere in the operators reach,
wire connections included
• Allows the operator to make “on the fly”
rate adjustments from the cab
• Allows easy connection with blower kit
NOTE: The rate chart was created using a product with
a density of 100 pounds per cubic foot. The flow rate
will change proportionately with the density. Testing
was done with a power source of 13.8 volts, different
power input voltages will change the application rate.
30’ Power Cord with Battery Clips
AM-1BK
The Augra Meter is designed for granular application at the blower or
bagger, or on a small square baler or pull-type forage harvester. For
self-propelled forage harvesters the AM-1BK (on this page) is
recommended. For round or large square balers, both the AM-1BK (on
this page) and AM-1BKD (on page 7) are recommended.
AM-1BK Blower Kit
(As shown displayed on Augra Meter)
The AM-1BK is designed to work with any 12 volt Augra Meter. This kit uses
the air from the blower to move the granular product through a flex hose to
your desired application point.
12 Volt Blower Fan
12’ of Flex Hose
30’ Power Cord
Pre-assembled, easy to install
6
(320) 252-8999
AM-1BKD Blower Kit Diffuser
The AM-1BKD is an attachment for the AM-1BK. With the Blower Kit, this
improved diffuser creates a wider and more consistant spray pattern than
previous methods.
AM-1BKD
DE-5 Gravity Applicator
The DE-5 can be used with dry granular or liquid preservatives.
(It will NOT work with powdery products)
Mounts Either Hanging or Standing
• Simple reversal of brackets change the mounting position
Rates are Controlled with Color Coded Orifices
• Liquid application rate = 22-46 ounces per minute
• Granular application rate = 1/4 to 1 pound per minute
DE-5
NOTE: When using the DE-5 with granular product application, it must be
used on moving and/or shaking equipment.
Transfer Pumps (12 Volt)
There are 2 different models of transfer pumps available.
• TS-3 Transfer Unit (3.0 Gallons Per Minute)
• TS-5 Transfer Unit (5.0 Gallons Per Minute)
Both units include the following:
• Hangs on the side of a tote or 55 gallon drum
• 12 Volt Self Priming Pump with Pressure Switch
• 3 Valve 3.0 GPM (TS-3)
• 5 Valve 5.0 GPM (TS-5)
• 15’ of Discharge Hose with Nozzle Valve
• 15’ Power Cord with Battery Clips
• on-off switch mounted on applicator
TS-3
7
Mounting kits
LS-1 Mounting Kit
The LS-1 Mounting Kit is designed for mounting the DE-55
or DE-100 Applicators on large square balers. This kit
allows the applicator tank and frame to be mounted over the
bale chute. Our mounting kit includes an easy to mount
pump unit bracket, easy to mount nozzle plate (LS-1/NP)
and upgrades of the in-line gauge from a 2 1/2” to a 4” liquid
filled gauge (ILG-4), making it easy to read from the cab.
Also included are longer lengths of hose and power cord
needed for proper installation.
LS-1 Mounting Bracket
ILG-4
LS-1/NP
JDRD Mounting Kit
JDRD Mounting Brackets
The JDRD is a mounting kit designed for mounting our DE-25 Applicator on
John Deere Round Balers. This mounting kit may be adapted to be used
for other round balers as well. The JDRD also includes two of our easy to
mount #184 Round Baler Nozzle Brackets with U-Bolts for easier nozzle
installation on round balers.
NOTE: #184 Round Baler Nozzle Brackets are recommended for use with
most makes of round balers. One is needed for each nozzle installed.
#184 Round Baler Nozzle Bracket
CM-1 Chopper Mount
The CM-1 Chopper Mounting Kit is a universal mount designed to mount
either a DE-45 or DE-25 Applicator on a pull-type chopper. Nuts and bolts
are included.
CM-1 Pull-Type Chopper Mounting Kit
8
(320) 252-8999
Moisture
testers
FX-2000 Series Moisture Testers
The FX-2000 Series moisture testers from Delmhorst include an in-chamber moisture sensor to provide you
with “on-the-go” readings. These units take 2 readings every second and update the readings every 4
seconds when attached to the in-chamber tester. They display the average and highest of eight
accumulated readings on a backlit display. Measures moisture between 6% - 40%.
FX-2000/PKG
FX-2018/PKG (not pictured)
FX-2000/PKG
Includes:
• Digital Display with 3 Year Manufacturer Warranty
• In-Chamber Moisture Sensor
• H-4 External Handle (for Prod and “Windrow” Prod)
• 10” Prod for H-4 Handle (FX-2000/PKG Only)
• 18” Prod for H-4 Handle (FX-2018/PKG Only)
• “Windrow” Prod for H-4 Handle
• Carrying Case
FX-2000
FX-2000
Includes:
• In-Chamber Moisture Sensor
F-2000 Series Moisture Testers
The F-2000 Series moisture testers from Delmhorst are designed for portable use. These units average
up to 100 accumulated readings. Measures moisture between 6% - 40%.
F-2000/PKG
F-2018/PKG (not pictured)
Includes:
• H-4 External Handle (for Prod and “Windrow” Prod)
• 10” Prod for H-4 Handle (F-2000/PKG Only)
• 18” Prod for H-4 Handle (F-2018/PKG Only)
• “Windrow” Prod for H-4 Handle
• Carrying Case
F-2000/PKG
F-2000
F-2000
Includes:
• 10” Prod (attaches directly to Digital Display)
9
Flow
meters
DigiFlow Digital Flowmeter
Designed with the custom operator in mind, the DigiFlow is a digital
flowmeter that includes a digital console with easy to read backlit display
to mount in the cab.
NOTE: NOT for use with water soluble bacterial products.
In cab console
• Provides Flow Rate in Gallons, Liters
or Pounds Per Hour
• Required Flow Rate:
5-140 GPH (18-540 LPH)
DigiFlow Digital Flowmeter
• Total Flow Reading (resettable)
Provides total flow since last reset.
Great for billing out product!
• Easy-Cal System
• Allows user to calibrate system for their specific product regardless of density or viscosity
• Accurate calibration, assures proper product application/billing
“Ball Type” Flowmeter
Assemblies
3 Ranges
Available:
FL1-___ Flowmeter Assembly with Hose
10
(320) 252-8999
• FL1-12: 2-12 GPH
• FL1-40: 4-40 GPH
• FL1-100: 10-100 GPH
The FL Series Flowmeters are “ball type” flowmeters. These flowmeters
are available in 3 different ranges and can be purchased as a complete
assembly or as a replacement of existing “ball type” flowmeters. All of the
flowmeter assemblies come complete with a mounting bracket, 20’ of 3/8”
braided hose, fittings and hose clamps. These flowmeters show the
current application rate in gallons per hour. NOTE: The FL Series
Flowmeters do not have a total flow reading (see the DigiFlow above for
this and other features).
Controls
SP-1 Speed Control
The SP-1 control module has an on-off switch with an LED
on indicator with a dial that controls the speed of the
pump. It will allow the operator to control the pressure and
spray volume from the cab or away from the pump unit
where required. Our SP-1 includes reverse polarity
protection, a 10 amp resettable circuit breaker and swivel
mounting kit. This unit works great on all 12 volt Ag-Serv
Applicators. (Not for use with DE-1000)
Speed Control
SP-1s Speed Control
Similar to the SP-1 but includes a separate auxillary on/off
switch for an additional accessory.
Digital Timers
DT-1a
• 110 Volt Digital Timer
This timer comes in a weather/dust resistant box and
have standards extension cord plugs; this allows the timer
to be mounted anywhere between the power source and
the applicator using extension cords.
DT-1a-12
• 12 Volt Digital Timer
This timer operates on a 12 volt system.
DT-1a Timer
MT-1 Timer
The MT-1 Timer is a manual wind-up spring timer. This
unit can be set for a run time of up to 10 minutes and
may be used on any 12 volt applicator.
MT-1 Timer
11
(320) 252-8999
316 33rd Ave South | Waite Park, MN 56387
CATALOG 2010
Dohrmann
Enterprises, Inc.

Dohrmann Applicators

Transcription

Similar documents

KITCHEN FAUCETS

X-TARMAC HANDGUARDS PARAMANI X

ACANTHUS TOWEL RING | 3430

Read the Sauer

Presented by Tim O`Connell President, Rescue 42, Inc.

Mineflex Brochure - Reel Easy

Quick Guide

Offering more

quick start guide

Select Design Premium Conversions