NEWCO Cast Steel Valves Technical Data Sheet

Transcription

NEWCO®
Cast Steel Valves
Technical Data
TC9308-3
All the information contained in this manual is the exclusive property of Cameron. Any reproduction or use of the calculations, drawings, photographs, procedures or instructions, either
expressed or implied, is forbidden without the written permission of Cameron or its authorized agent.
Initial Release 01
October 2013
Produced by Technical Publications, Houston, TX, USA
© 2013 Cameron
TC9308-3
2
PREFACE
The procedures included in this book are to be performed in conjunction with the requirements
and recommendations outlined in API Specifications. Any repairs to the equipment covered by
this book should be done by an authorized Cameron service representative. Cameron will not
be responsible for loss or expense resulting from any failure of equipment or any damage to any
property or death or injury to any person resulting in whole or in part from repairs performed
by anyone other than authorized Cameron personnel. Such unauthorized repairs shall also serve
to terminate any contractual or other warranty, if any, on the equipment and may also result in
equipment no longer meeting applicable requirements.
File copies of this manual are maintained. Revisions and/or additions will be made as deemed
necessary by Cameron. The drawings in this book are not drawn to scale, but the dimensions
shown are accurate.
This book covers Cameron products.
Cameron
P.O. Box 1212
Houston, Texas 77251-1212
713-939-2211
http://www.c-a-m.com
TC9308-3
3
NOTES:
TC9308-3
4
TABLE OF CONTENTS
Overview..............................................................................................................................7
I.
Cast Steel Bolted Bonnet Gate Valves.......................................................................18
Sizes: 2” to 48” • Pressure Class: 150 to 1500
II.
Cast Steel Bolted Bonnet Globe Valves.....................................................................30
III.
Cast Steel Bolted Bonnet Angle Valves.....................................................................42
IV. Cast Steel Bolted Cover Swing Check Valves............................................................50
V.
Cast Steel Bolted Cover Tilting Disc Check Valves....................................................62
(Pressure Seal 600 to 2500)
VI. Cast Steel Bolted Bonnet Stop Check Valves............................................................68
VII. Cast Steel Bolted Bonnet Angle Stop Check Valves.................................................80
VIII. How to Order All Cameron’s NEWCO Products........................................................88
IX. Industry Standards Typically Used in Valve Manufacturing.....................................90
TC9308-3
5
NOTES:
TC9308-3
6
OVERVIEW
Valve and I.D. Tag Overview
The identification tag displays all construction and tracking data regarding the respective
valve on which it is attached. Below is a general overview of the identification tag components.
I.D. tags are located in 1 of the 3 following areas:
•Yoke
•Body/Bonnet Flange
•Under The Handwheel Nut
I.D. Tag Locations
Heat No.
Pressure Temperature Rating
Trim Description
Model
C5/CR13, CR13, HF
FIG. 13F-C5/2
750 PSI @ 100 °F
B16.34 CLASS 300
API 600/ISO10434
NPS 2
S/N 100419
NEWCO
6
300
WCB
77
T5158
Pressure Class
Nominal Port Size
Serial Number
TC9308-3
7
Brand
Size
Pressure Class
Body Material
Pattern
Heat No.
Body/Bonnet Materials
Cameron’s NEWCO® cast steel valves are available in stock in a wide range of body/bonnet
materials and optional trim materials. Listed below are some of the more popular materials. Additional materials are available. Please contact Cameron or your local distributor
for details.
Material
Designation
Common
Description
ASTM
Specs.
Body/Bonnet
Material Service Limitations*
CB
Carbon Steel
A216
Non-corrosive service water, oil and gases at temperatures
between -20º F and +800º F.
LCC
Low Temp. Carbon
A352
Low temperature service between -50º F and +650º F.
WC6
1.25% Chrome and
.5% Moly
A217
Non-corrosive service water, oil and gases at temperatures
WC9
2.25% Chrome and
1% Moly
A217
Non-corrosive service water, oil, and gases at temperatures
C5
5% Chrome and
.5% Moly
A217
Corrosive, non-corrosive or erosive service at temperatures
C12
9% Chrome and
1% Moly
A217
C12A
9% Chrome, 1%
Moly and V
A217
C8M
Cast 316
A351
Corrosive, cryogenic or high temperature service between
-450º F and +1200º F.
A20
Alloy 20
A351
Corrosive service at temperatures between -20º F and +300º F.
* Limitations are per 2004 Edition of ASME B16.34.
Trim Materials
The following are Cameron’s NEWCO standard trim designations.
Wedge or
Disc
Facing (1)
Stem
Other
Trim
Parts (2)
CR 13
CR 13
CR 13
CR 13
Non-corrosive applications.
Steam, gas and general
service to 700º F. Oil and oil
vapor to 900º F.
8
HF
CR 13
CR 13
CR 13
Steam, gas and general
service to 1000º F. Standard
trim for gate valves.
Full Stellite
5
HF
HF
CR 13
CR 13
Premium trim service to
1200º F. Excellent for high
pressure water and steam
service.
316
10
316
316
316
316
Corrosive services to 850º
F. Low temperature service
standard for 316 SS valves.
Trim
Number
Common
Name
1
13 Chrome
1
2
Half Stellite
3
4
TC9308-3
API 600 Seat Ring
Trim No. Facing (1)
8
Service Limitations
Wedge or
Disc
Facing (1)
Stem
Other
Trim
Parts (2)
HF
316
316
316
16
HF
HF
316
316
Monel
9
NiCu
NiCu
NiCu
NiCu
5/2
Monel/Half
Stellite
11
HF
NiCu
NiCu
NiCu
5/3
Monel/Full
Stellite
-
HF
HF
NiCu
NiCu
6
Alloy 20
13
A20
A20
A20
A20
Corrosive services to 300º F.
7
Bronze
-
BRZ
BRZ
BRZ
BRZ
Water, gas or low pressure
steam to 450º F.
A7
Aluminum
Bronze
-
AL BRZ
AL BRZ
AL BRZ
AL BRZ
8
Iron
-
Iron
Iron
STL
Iron or
STL
X
Special
Special
Special
Special
Special
Special
Trim
Number
Common
Name
API 600 Seat Ring
Trim No. Facing (1)
4/2
316/Half
Stellite
12
4/3
316/Full
Stellite
5
Service Limitations
Corrosive services to 750º F.
Customer to specify.
(1) Facing is defined as the seating surface of a seat ring and wedge/disc.
(2) Other trim parts are defined as small internal parts that are normally in contact with the service fluid. This includes the stem, backseat bushing in gate and globe valves and the swing check disc nut.
Sour Gas Service Materials
Cameron’s NEWCO cast steel valves may be furnished with body and trim materials in
compliance with NACE MR-01-75 specifications. The standard valve is WCB with double
tempered trim 2 and Class II bolting. Other materials, trim and bolting are available.
Features and Benefits
•Certifications
•International Organization for Standardization (ISO)
•Traceability
•Fugitive Emmisions Tested
•API-598 Tested
•Major End-user Approved
•Multiple North American Locations
•Extensive Engineering Capabilities
•Excellent Customer Service
•Warranty
•Onsite Non-destructive Testing
•Field Services for Start-up
•Inhouse Automation Capabilities
TC9308-3
9
Pressure Temperature Ratings - ASME B16.34 - 2004
Class 150
Temperature °F (°C)
WCB*
LCC
WC6
WC9
C5
C12
C12A
-20 to 100 (-29 to 38)
200 (93)
300 (148)
400 (204)
500 (260)
600 (316)
650 (343)
700 (371)
750 (399)
800 (427)
850 (454)
900 (482)
950 (510)
1000 (538)
1050 (566)
1100 (593)
1150 (621)
1200 (649)
285
260
230
200
170
140
125
110
95
80
65
50
35
20
-
290
260
230
200
170
140
125
-
290
260
230
200
170
140
125
110
95
80
65
50
35
20
20**
20**
-
290
260
230
200
170
140
125
110
95
80
65
50
35
20
20**
20**
-
290
260
230
200
170
140
125
110
95
80
65
50
35
20
20**
20**
20**
20**
290
260
230
200
170
140
125
110
95
80
65
50
35
20
20**
20**
20**
20**
290
260
230
200
170
140
125
110
95
80
65
50
35
20
20
20
20
20
Class 300
TC9308-3
WCB*
LCC
WC6
WC9
C5
C12
C12A
-20 to 100 (-29 to 38)
200 (93)
300 (148)
400 (204)
500 (260)
600 (316)
650 (343)
700 (371)
750 (399)
800 (427)
850 (454)
900 (482)
950 (510)
1000 (538)
1050 (566)
1100 (593)
1150 (621)
1200 (649)
740
680
655
635
605
570
550
530
505
410
320
230
135
85
-
750
750
730
705
665
605
590
-
750
750
720
695
665
605
590
570
530
510
485
450
320
215
145
95
65
40
750
750
730
705
665
605
590
570
530
500
485
450
385
265
175
110
70
40
750
750
730
705
665
605
590
570
530
510
485
375
275
200
145
100
60
35
750
750
730
705
665
605
590
570
530
510
485
450
375
255
170
115
75
50
750
750
730
705
665
605
590
570
530
510
485
450
385
365
360
300
225
145
10
Class 600
WCB*
LCC
WC6
WC9
C5
C12
C12A
-20 to 100 (-29 to 38)
200 (93)
300 (148)
400 (204)
500 (260)
600 (316)
650 (343)
700 (371)
750 (399)
800 (427)
850 (454)
900 (482)
950 (510)
1000 (538)
1050 (566)
1100 (593)
1150 (621)
1200 (649)
1480
1360
1310
1265
1205
1135
1100
1060
1015
825
640
460
275
170
-
1500
1500
1455
1405
1330
1210
1175
-
1500
1500
1445
1385
1330
1210
1175
1135
1065
1015
975
900
640
430
290
190
130
80
1500
1500
1455
1410
1330
1210
1175
1135
1065
1015
975
900
755
535
350
220
135
80
1500
1500
1455
1410
1330
1210
1175
1135
1065
1015
975
745
550
400
290
200
125
70
1500
1500
1455
1410
1330
1210
1175
1135
1065
1015
975
900
755
505
345
225
150
105
1500
1500
1455
1410
1330
1210
1175
1135
1065
1015
975
900
775
725
720
605
445
290
Class 900
TC9308-3
WCB*
LCC
WC6
WC9
C5
C12
C12A
-20 to 100 (-29 to 38)
200 (93)
300 (148)
400 (204)
500 (260)
600 (316)
650 (343)
700 (371)
750 (399)
800 (427)
850 (454)
900 (482)
950 (510)
1000 (538)
1050 (566)
1100 (593)
1150 (621)
1200 (649)
2220
2035
1965
1900
1810
1705
1650
1590
1520
1235
955
690
410
255
-
2250
2250
2185
2110
1995
1815
1765
-
2250
2250
2165
2080
1995
1815
1765
1705
1595
1525
1460
1350
955
650
430
290
195
125
2250
2250
2185
2115
1995
1815
1765
1705
1595
1525
1460
1350
1160
805
525
330
205
125
2250
2250
2185
2115
1995
1815
1765
1705
1595
1525
1460
1120
825
595
430
300
185
105
2250
2250
2185
2115
1995
1815
1765
1705
1595
1525
1460
1350
1130
760
515
340
225
155
2250
2250
2185
2115
1995
1815
1765
1705
1595
1525
1460
1350
1160
1090
1080
905
670
430
11
Class 1500
WCB*
LCC
WC6
WC9
C5
C12
C12A
-20 to 100 (-29 to 38)
200 (93)
300 (148)
400 (204)
500 (260)
600 (316)
650 (343)
700 (371)
750 (399)
800 (427)
850 (454)
900 (482)
950 (510)
1000 (538)
1050 (566)
1100 (593)
1150 (621)
1200 (649)
3705
3395
3270
3170
3015
2840
2745
2665
2535
2055
1595
1150
685
430
-
3750
3750
3640
3520
3325
3025
2940
-
3750
3750
3610
3465
3325
3025
2940
2840
2660
2540
2435
2245
1595
1080
720
480
325
205
3750
3750
3640
3530
3325
3025
2940
2840
2660
2540
2435
2245
1930
1335
875
550
345
205
3750
3750
3640
3530
3325
3025
2940
2840
2660
2540
2435
1870
1370
995
720
495
310
170
3750
3750
3640
3530
3325
3025
2940
2840
2660
2540
2435
2245
1885
1270
855
565
375
255
3750
3750
3640
3530
3325
3025
2940
2840
2660
2540
2435
2245
1930
1820
1800
1510
1115
720
Class 2500
WCB*
LCC
WC6
WC9
C5
C12
C12A
-20 to 100 (-29 to 38)
200 (93)
300 (148)
400 (204)
500 (260)
600 (316)
650 (343)
700 (371)
750 (399)
800 (427)
850 (454)
900 (482)
950 (510)
1000 (538)
1050 (566)
1100 (593)
1150 (621)
1200 (649)
6170
5655
5450
5280
5025
4730
4575
4425
4230
3430
2655
1915
1145
715
-
6250
6250
6070
5865
5540
5040
4905
-
6250
6250
6015
5775
5540
5040
4905
4730
4430
4230
4060
3745
2655
1800
1200
800
545
345
6250
6250
6070
5880
5540
5040
4905
4730
4430
4230
4060
3745
3220
2230
1455
915
570
345
6250
6250
6070
5880
5540
5040
4905
4730
4430
4230
4060
3115
2285
1655
1200
830
515
285
6250
6250
6070
5880
5540
5040
4905
4730
4430
4230
4060
3745
3145
2115
1430
945
630
430
6250
6250
6070
5880
5540
5040
4905
4730
4430
4230
4060
3745
3220
3030
3000
2515
1855
1200
* Not recommended for prolonged use above 800° F.
** For weld end valves only. Flanged end ratings terminate at 1000° F.
Note: Packing, gasket, or bolting may limit temperature. Please advise service temperature if
above 1000° F. Ratings from ASME B16.34 standard class valves. Special class weld end
valves to ASME B16.34 are available on special order.
TC9308-3
12
Flange Dimensions - ASME B16.5
Class 150 and 300
1/16”
C
1/4”
C
A
D
E
B
Class 600 through 2500
A
D
E
B
Standards: NPS 24 and smaller in all classes conform to ASME B16.5. NPS 30 and larger
conform to ASME B16.47 (Series A).
Facing: End flanges are regularly furnished with a raised face having a serrated finish per
MSS SP-6. The thickness of the flange dimension (C) includes the raised face for Class 150
and 300. For Class 600 through 2500, the flange dimension (C) does not include the 1/4”
raised face.
Bolt Holes: Bolt holes are 1/8” larger than the bolt diameter. Bolt holes are drilled to
straddle the center line.
TC9308-3
13
Flange Dimensions in Inches
Class 150
Size
In. (mm)
A
B
C
D
E
2 (50)
2.5 (65)
3 (80)
4 (100)
5 (125)
6 (150)
8 (200)
10 (250)
12 (300)
14 (350)
16 (400)
18 (450)
20 (500)
24 (600)
30 (750)
36 (900)
42 (1050)
48 (1200)
2.00
2.50
3.00
4.00
5.00
6.00
8.00
10.00
12.00
13.25
15.25
17.25
19.25
23.25
29.25
35.06
40.87
46.00
6.00
7.00
7.50
9.00
10.00
11.00
13.50
16.00
19.00
21.00
23.50
25.00
27.50
32.00
38.75
46.00
53.00
59.50
0.75
0.88
0.94
0.94
0.94
1.00
1.12
1.19
1.25
1.38
1.44
1.56
1.69
1.88
2.94
3.56
3.81
4.25
3.62
4.12
5.00
6.19
7.31
8.50
10.62
12.75
15.00
16.25
18.50
21.00
23.00
27.25
33.75
40.25
47.00
53.50
4.75
5.50
6.00
7.50
8.50
9.50
11.75
14.25
17.00
18.75
21.25
22.75
25.00
29.50
36.00
42.75
49.50
56.00
Stud Bolts
No.
Diam.
Hole
Diam.
4
4
4
8
8
8
8
12
12
12
16
16
20
20
28
32
36
44
0.63
0.63
0.63
0.63
0.75
0.75
0.75
0.88
0.88
1.00
1.00
1.125
1.125
1.25
1.25
1.50
1.50
1.50
0.75
0.75
0.75
0.75
0.88
0.88
0.88
1.00
1.00
1.13
1.13
1.25
1.25
1.38
1.38
1.63
1.63
1.63
Class 300
TC9308-3
Size
In. (mm)
A
B
C
D
E
2 (50)
2.5 (65)
3 (80)
4 (100)
5 (125)
6 (150)
8 (200)
10 (250)
12 (300)
14 (350)
16 (400)
18 (450)
20 (500)
24 (600)
30 (750)
36 (900)
2.00
2.50
3.00
4.00
5.00
6.00
8.00
10.00
12.00
13.25
15.25
17.00
19.00
23.00
29.00
34.50
6.50
7.50
8.25
10.00
11.00
12.50
15.00
17.50
20.50
23.00
25.50
28.00
30.50
36.00
43.00
50.00
0.88
1.00
1.12
1.25
1.38
1.44
1.62
1.88
2.00
2.12
2.25
2.38
2.50
2.75
3.62
4.12
3.62
4.12
5.00
6.19
7.31
8.50
10.62
12.75
15.00
16.25
18.50
21.00
23.00
27.25
33.75
40.25
5.00
5.88
6.62
7.88
9.25
10.62
13.00
15.25
17.75
20.25
22.50
24.75
27.00
32.00
39.25
46.00
14
Stud Bolts
No.
Diam.
Hole
Diam.
8
8
8
8
8
12
12
16
16
20
20
24
24
24
28
32
0.63
0.75
0.75
0.75
0.75
0.75
0.88
1.00
1.13
1.13
1.25
1.25
1.25
1.50
1.75
2.00
0.75
0.88
0.88
0.88
0.88
0.88
1.00
1.13
1.25
1.25
1.38
1.38
1.38
1.63
1.88
2.13
Class 600
Size
In. (mm)
A
B
C
D
E
2 (50)
2.5 (65)
3 (80)
4 (100)
5 (125)
6 (150)
8 (200)
10 (250)
12 (300)
14 (350)
16 (400)
18 (450)
20 (500)
24 (600)
30 (750)
36 (900)
2.00
2.50
3.00
4.00
5.00
6.00
8.00
10.00
12.00
13.25
15.25
17.00
19.00
23.00
29.00
34.50
6.50
7.50
8.25
10.00
11.00
12.50
15.00
17.50
20.50
23.00
25.50
28.00
30.50
36.00
43.00
50.00
0.88
1.00
1.12
1.25
1.38
1.44
1.62
1.88
2.00
2.12
2.25
2.38
2.50
2.75
3.62
4.12
3.62
4.12
5.00
6.19
7.31
8.50
10.62
12.75
15.00
16.25
18.50
21.00
23.00
27.25
33.75
40.25
5.00
5.88
6.62
7.88
9.25
10.62
13.00
15.25
17.75
20.25
22.50
24.75
27.00
32.00
39.25
46.00
Stud Bolts
No.
Diam.
Hole
Diam.
8
8
8
8
8
12
12
16
16
20
20
24
24
24
28
32
0.63
0.75
0.75
0.75
0.75
0.75
0.88
1.00
1.13
1.13
1.25
1.25
1.25
1.50
1.75
2.00
0.75
0.88
0.88
0.88
0.88
0.88
1.00
1.13
1.25
1.25
1.38
1.38
1.38
1.63
1.88
2.13
Class 900
TC9308-3
Size
In. (mm)
A
B
C
D
E
2 (50)
2.5 (65)
3 (80)
4 (100)
5 (125)
6 (150)
8 (200)
10 (250)
12 (300)
14 (350)
16 (400)
18 (450)
20 (500)
24 (600)
1.88
2.25
2.88
3.88
4.75
5.75
7.50
9.38
11.12
12.25
14.00
15.75
17.50
21.00
8.50
9.62
9.50
11.50
13.75
15.00
18.50
21.50
24.00
25.25
27.75
31.00
33.75
41.00
1.50
1.62
1.50
1.75
2.00
2.19
2.50
2.75
3.12
3.38
3.50
4.00
4.25
5.50
3.62
4.12
5.00
6.19
7.31
8.50
10.62
12.75
15.00
16.25
18.50
21.00
23.00
27.25
6.50
7.50
7.500
9.25
11.00
12.50
15.50
18.50
21.00
22.00
24.25
27.00
29.50
35.50
15
Stud Bolts
No.
Diam.
Hole
Diam.
8
8
8
8
8
12
12
16
20
20
20
20
20
20
0.88
1.00
0.88
1.13
1.25
1.13
1.38
1.38
1.38
1.50
1.63
1.88
2.00
2.50
1.00
1.13
1.00
1.25
1.38
1.25
1.50
1.50
1.50
1.63
1.75
2.00
2.13
2.63
Class 1500
Size
In. (mm)
A
B
C
D
E
2 (50)
2.5 (65)
3 (80)
4 (100)
5 (125)
6 (150)
8 (200)
10 (250)
12 (300)
14 (350)
16 (400)
18 (450)
20 (500)
24 (600)
1.88
2.25
2.75
3.62
4.38
5.38
7.00
8.75
10.38
11.38
13.00
14.62
16.38
19.62
8.50
9.62
10.50
12.25
14.75
15.50
19.00
23.00
26.50
29.50
32.50
36.00
38.75
46.00
1.50
1.62
1.88
2.12
2.88
3.25
3.62
4.25
4.88
5.25
5.75
6.38
7.00
8.00
3.62
4.12
5.00
6.19
7.31
8.50
10.62
12.75
15.00
16.25
18.50
21.00
23.00
27.25
6.50
7.50
8.00
9.50
11.50
12.50
15.50
19.00
22.50
25.00
27.75
30.50
32.75
39.00
Stud Bolts
No.
Diam.
Hole
Diam.
8
8
8
8
8
12
12
12
16
16
16
16
16
16
0.88
1.00
1.13
1.25
1.50
1.38
1.63
1.88
2.00
2.25
2.50
2.75
3.00
3.50
1.00
1.13
1.25
1.38
1.63
1.50
1.75
2.00
2.13
2.38
2.63
2.88
3.13
3.63
Class 2500
Size
In. (mm)
A
B
C
D
E
2 (50)
2.5 (65)
3 (80)
4 (100)
5 (125)
6 (150)
8 (200)
10 (250)
12 (300)
1.50
1.88
2.25
2.88
3.62
4.38
5.75
7.25
8.62
9.25
10.50
12.00
14.00
16.50
19.00
21.75
26.50
30.00
2.00
2.25
2.62
3.00
3.62
4.25
5.00
6.50
7.25
3.62
4.12
5.00
6.19
7.31
8.50
10.62
12.75
15.00
6.75
7.75
9.00
10.75
12.75
14.50
17.25
21.75
24.38
Stud Bolts
No.
Diam.
Hole
Diam.
8
8
8
8
8
8
12
12
12
1.00
1.13
1.25
1.50
1.75
2.00
2.00
2.50
2.75
1.13
1.25
1.38
1.63
1.88
2.13
2.13
2.63
2.88
Auxiliary Connection Locations (Bypasses, Drains, etc.)
Bypasses
Bypasses serve two purposes. They are used in steam services as a means to warm
the line before the main valve is opened. They are also used to balance the pressure
on both sides of the main valve as an aid to reduce the torque required to open the
main valve.
Cameron’s NEWCO cast steel valve can be furnished with all welded bypasses when
specified. The standard bypass configuration is the single valve bypass attached to
the side of the main valve with the stems of both valves parallel as shown below.
Piping and the OS&Y globe bypass valve have a pressure-temperature rating and
corrosion resistance equal to exceeding that of the main valve.
TC9308-3
16
When other bypass configurations are required, a sketch or drawing must accompany the order.
Drains
Cameron’s NEWCO cast steel valves can be furnished with drains at any of the locations shown. Standard drain connections consist of a drilled, tapped, and plugged
hole at the location(s) specified. Other types of drains, including welding or threaded nipples with or without shut-off valves, can also be furnished when specified.
Please refer to ASME B16.34 for exact auxiliary connection locations, sizes and
threading information.
Each letter in the illustration(s) below identifies the possible hole locations for auxiliary connection(s). These illustrations are for reference purposes only.
Unless specified otherwise, auxiliary connection hole sizes shall be drilled and
tapped as follows:
• 2” through 4” utilizes a .50” hole
• 5” through 8” utilizes a .75” hole
• 10” and larger utilizes a 1” hole
Gate Valves
Check Valves
Globe Valves
Angle Valves
TC9308-3
17
I. CAST STEEL BOLTED BONNET GATE VALVES
SIZES: 2” TO 48” (50MM TO 1200MM) • PRESSURE CLASS: 150 TO 1500
Typical Cast Steel Bolted Bonnet Gate Valve Expanded View
17
18
16
15
8
7
12
14
23
10
3
2
9
13
11
21
4
6
19
20
5
21
1
22
TC9308-3
18
1. Body: Cameron’s NEWCO cast steel bodies provide low resistance flow and optimum
strength and performance.
2. Yoke and Bonnet: Cameron’s NEWCO bonnet assemblies are built to the same standards as the bodies. Larger size gate valves utilize a multi-piece bonnet design.
3. Grease Fitting: The grease fitting allows for easy stem lubrication.
4. Stem: The stem is precision machined and inserts into the horizontal channel in the
disc.
5. Wedge: Cameron’s 1-piece flex wedge is machined to the tightest tolerances to ensure
trouble free shut-off and cycling.
6. Back Seat Bushing: The back seat, when engaged with the stem head, provides a stable
shut-off to the stuffing box which isolates the packing from flow exposure.
7. Gland: The gland compresses the packing to create a stem seal above the back seat,
between the bonnet and stem.
8. Gland Flange: The gland flange applies pressure to the gland for accurate packing adjustments.
9. & 10. Gland Bolts and Nuts: The gland bolts and nuts allow for easy adjustments for
packing compression.
11. Gland Bolt Pin: The gland bolt pin secures the gland bolts to the yoke and bonnet.
12. Packing: The packing creates a seal above the back seat, between the bonnet and
stem.
13. Stuffing Box: The stuffing box contains the packing.
14. Stem Nut: The stem nut provides a precision guide for proper stem alignment.
15. Yoke Bushing: The retaining nut secures the stem nut to the bonnet assembly.
16. Handwheel: The handwheel cycles the valve.
17. Handwheel Nut: The handwheel nut secures the handwheel to the bonnet assembly.
18. Set Screw: The set screw prevents handwheel nut loosening.
19. Bonnet Gasket: The bonnet gasket creates a leakproof seal between the bonnet and
body.
20. & 21. Bonnet Studs and Nuts: The bonnet studs and nuts secure the bonnet to the
body.
22. Seat Rings: To ensure a stable shut-off, seat rings are aligned and seal-welded into the
valve, then precision ground for optimal seating.
23. Spacer Ring: Assists the packing rings in creating a seal above the back seat, between
the bonnet and stem.
TC9308-3
19
Styles: CB2, CB3 and CB4/2
Class 150 - Sizes: 2” to 48”
Pressure Class Range: 150 to 1500
Design and Manufacturing Standards
Valve Design: ASME B16.34/API 600
Flange Dimensions: ASME B16.5, B16.47 (Series A)
Face to Face Dimensions: ASME B16.10
Tested in Accordance With: API 598
Recommended Spare Parts*
C
B
(open)
Optional split-yoke and
vertical handwheel.
A-RF & RTJ
A-BW
** Gear operated is standard. Handwheel available upon request.
TC9308-3
20
Typical Bill of Materials (See page 89 for available materials)
Component
CB2
Body
Seat Rings
Wedge 2” - 3”
Wedge 4” and larger
Stem
Yoke and Bonnet
*Bonnet Gasket
Bonnet Nuts
Bonnet Studs
Back Seat Bushing
*Packing
Gland
Gland Flange
Gland Bolt Pins
Gland Bolts
Gland Nuts
Nameplate
Nameplate Rivets
Grease Fitting
Stem Nut
Yoke Bushing
Handwheel
Handwheel Nut
Set Screw
Spacer Ring
CB3
CB4/2
ASTM A216-WCB
ASTM A105/HF
ASTM A276-410
ASTM A351- CF8M/A276-316
ASTM A216-WCB/HF
ASTM A216-WCB w/13% Chrome
ASTM A216-WCB w/316 Hardface
ASTM A182-F6a
ASTM A182-316
ASTM A216-WCB
Multilayered Corrugated 316 w/Graphite
ASTM A194-2H
ASTM A194-2HM
ASTM A193-B7
ASTM A193-B7M
ASTM A276-410
ASTM A276-316
Graphite w/Braided Carbon Fiber End Rings
ASTM A276-410
ASTM A276-316
ASTM A216-WCB
ASTM A36
ASTM A307-B
ASTM A194-2H
Stainless Steel 304
Stainless Steel - Commercial
Carbon Steel - Commercial
ASTM A439-D2
ASTM A536 (65-45-12)
ASTM A536 (65-45-12)
ASTM A536 (65-45-12)
ASTM A193-B6
N/A
Class 150
Size
NPS
2
2.5
3
DN
50
65
80
In
mm
In
A-BW
mm
In
B
mm
In
C
mm
RF Lbs
Wt. Kg
BW Lbs
Wt. Kg
A-RF
4
5
6
8
10
12
14
16
18
20
24
30
36
42
48
100 125 150 200 250 300 350 400 450 500 600 750 900 1050 1200
7.0 7.5 8.0 9.0 10.0
178 191 203 229 254
8.5 9.5 11.1 12.0 15.0
216 241 282 305 381
14.8 17.1 18.2 22.6 28.1
376 434 462 574 714
8.0 8.0 8.0 10.0 13.8
203 203 203 254 350
46
56
71 111 163
21
25
32
50
74
40
46
58
91 152
18
21
26
41
69
10.5
267
15.9
404
33.2
843
14.0
356
196
89
180
82
11.5
292
16.5
419
38.9
988
16.0
406
289
131
259
118
13.0
330
18.0
457
46.4
1179
18.0
457
449
204
425
193
14.0
356
19.8
503
54.6
1387
20.0
508
639
290
584
265
15.0
381
22.5
572
63.5
1613
22.0
559
860
391
811
369
16.0
406
24.0
610
72.4
1839
24.0
610
1190
541
1146
521
17.0
432
26.0
660
79.2
2012
27.0
686
1389
631
1349
613
18.0
457
28.0
711
86.0
2184
30.0
762
1786
812
1720
782
20.0
508
32.0
813
100.8
2560
30.0
762
2602
1183
2534
1152
24.0
610
24.0
610
125.1
3178
35.0
889
4466
2030
4037
1835
28.0
711
28.0
711
153.2
3891
43.0
1092
4850
1193
4385
1993
31.0
813
43.0
1092
174.4
4430
35.4
**900
10134
4600
10198
4625
34.0
864
46.0
1168
217.5
5525
35.4
**900
15677
8500
15545
8550
Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms. Larger sizes available on
request. Dimensions are subject to change without notice.
TC9308-3
21
Class 300 - Sizes: 2” to 36”
C
B
(open)
vertical handwheel.
A-RF
A-BW
TC9308-3
22
Component
CB2
Body
Seat Rings
Wedge 2” - 3”
Stem
Yoke and Bonnet
*Bonnet Gasket
Bonnet Nuts
Bonnet Studs
Back Seat Bushing
*Packing
Gland
Gland Flange
Gland Bolt Pins
Gland Bolts
Gland Nuts
Nameplate
Nameplate Rivets
Grease Fitting
Stem Nut
Yoke Bushing
Handwheel
Handwheel Nut
Set Screw
Spacer Ring
CB3
ASTM A276-410
ASTM A182-F6a
CB4/2
ASTM A216-WCB
ASTM A105/HF
ASTM A216-WCB/HF
ASTM A216-WCB/HF
ASTM A351-CF8M/A276-316
ASTM A182-316
ASTM A216-WCB
Spiral Wound 316 Stainless Steel/Graphite
ASTM A194-2H
ASTM A193-B7
ASTM A276-410
ASTM A276-410
ASTM A216-WCB
ASTM A36
ASTM A307-B
ASTM A194-2H
Stainless Steel 304
ASTM A439-D2
ASTM A536 (65-45-12)
ASTM A536 (65-45-12)
ASTM A536 (65-45-12)
ASTM A193-B6
ASTM A276-410
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
ASTM A276-316
Class 300
Size
NPS
2
2.5
3
4
5
6
8
10
12
14
16
18
20
24
30
36
DN
50
65
80
100
125
150
200
250
300
350
400
450
500
600
750
900
In
mm
In
mm
In
mm
In
mm
Lbs
Kg
Lbs
Kg
8.5
216
8.5
216
17.2
437
8.0
203
64
29
51
23
9.5
241
9.5
241
19.1
485
10.0
254
88
40
68
31
11.1
282
11.1
282
20.0
508
10.0
254
112
51
86
39
12.0
305
12.0
305
24.0
610
12.0
305
175
80
154
70
15.0
381
15.0
381
29.6
752
13.7
350
258
117
207
94
15.9
404
15.9
404
33.0
838
16.0
406
340
155
269
122
16.5
419
16.5
419
41.1
1044
18.0
457
542
246
430
195
18.0
457
18.0
457
49.3
1252
20.0
508
816
371
620
282
19.75
502
19.75
502
57.0
1448
22.0
559
1072
487
871
396
30.0
762
30.0
762
67.0
1702
25.2
640
1764
802
1323
601
33.0
838
33.0
838
73.1
1857
27.0
686
2183
992
1830
832
36.0
914
36.0
914
82.2
2088
27.0
686
2867
1303
2381
1082
39.0
991
39.0
991
95.5
2426
30.0
762
3682
1674
3109
1413
45.0 55.0 68.0
1143 1397 1727
45.0 55.0 68.0
1143 1397 1727
104.7 136.3 169.8
2659 3462 4312
30.0 31.9 31.9
762 **810 **810
5645 9702 15104
2566 4410 6850
4873 8350 11003
2215 3795 4990
A-RF
A-BW
B
C
RF
Wt.
BW
Wt.
TC9308-3
23
Class: 600 - Sizes: 2” to 24”
C
B
(open)
vertical handwheel.
A-BW
A-RF & RTJ
TC9308-3
24
Component
CB2
Body
Seat Rings
Wedge 2” - 3”
Stem
Yoke and Bonnet
*Bonnet Gasket
Bonnet Nuts
Bonnet Studs
Back Seat Bushing
*Packing
Gland
Gland Flange
Gland Bolt Pins
Gland Bolts
Gland Nuts
Nameplate
Nameplate Rivets
Grease Fitting
Stem Nut
Yoke Bushing
Handwheel
Handwheel Nut
Set Screw
Spacer Ring
CB3
ASTM A276-410
ASTM A182-F6a
CB4/2
ASTM A216-WCB
ASTM A105/HF
ASTM A216-WCB/HF
ASTM A216-WCB/HF
ASTM A351-CF8M/A276-316
ASTM A182-316
ASTM A216-WCB
Soft Steel Ring Joint
ASTM A194-2H
ASTM A193-B7
ASTM A276-410
ASTM A276-410
ASTM A216-WCB
ASTM A36
ASTM A307-B
ASTM A194-2H
Stainless Steel 304
ASTM A439-D2
ASTM A536 (65-45-12)
ASTM A536 (65-45-12)
ASTM A536 (65-45-12)
ASTM A193-B6
ASTM A276-410
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
ASTM A276-316
Class 600
Size
A-RF
A-BW
A-RTJ
B
C
RF-RTJ
Wt.
BW
Wt.
NPS
2
2.5
3
4
5
6
8
10
12
14
16
18
20
24
DN
50
65
80
100
125
150
200
250
300
350
400
450
500
600
In
mm
In
mm
In
mm
In
mm
In
mm
Lbs
Kg
Lbs
Kg
11.5
292
11.5
292
11.62
295
18.3
465
10.0
254
97
44
79
36
13.0
330
13.0
330
13.12
333
19.9
505
10.0
254
132
60
120
55
14.0
356
14.0
356
14.12
359
21.7
551
12.0
305
176
80
152
69
17.0
432
17.0
432
17.12
435
26.9
683
15.0
381
320
145
270
123
20.0
508
20.0
508
22.0
559
22.0
559
22.12
562
36.5
927
20.0
508
680
309
580
264
26.0
660
26.0
660
26.12
664
44.0
1118
24.0
610
1150
523
1020
464
31.0
787
31.0
787
31.12
791
52.8
1341
27.0
686
1715
780
1430
650
33.0
838
33.0
838
33.12
841
61.4
1560
27.0
686
2440
1109
1950
886
35.0
889
35.0
889
35.12
892
64.8
1646
30.0
762
3150
1432
2695
1225
39.0
991
39.0
991
39.12
994
71.7
1821
35.0
889
4415
2007
3800
1727
43.0
1092
43.0
1092
43.12
1095
79.3
2014
43.0
1092
5010
2277
5010
2277
47.0
1194
47.0
1194
47.25
1200
104.8
2662
43.0
1092
6853
3108
5640
2558
55.0
1397
55.0
1397
55.38
1406
116.9
2970
31.9
**810
10337
4688
8595
3898
31.6
803
18.0
457
520
236
430
195
TC9308-3
25
C
B
(open)
vertical handwheel.
A-RF
TC9308-3
A-BW
26
Component
CB2
Body
Seat Rings
Wedge 2” - 3”
Stem
Yoke and Bonnet
*Bonnet Gasket
Bonnet Nuts
Bonnet Studs
Back Seat Bushing
*Packing
Gland
Gland Flange
Gland Bolt Pins
Gland Bolts
Gland Nuts
Nameplate
Nameplate Rivets
Grease Fitting
Stem Nut
Yoke Bushing
Handwheel
Handwheel Nut
Set Screw
Spacer Ring
CB3
ASTM A276-410
ASTM A182-F6a
CB4/2
ASTM A216-WCB
ASTM A105/HF
ASTM A216-WCB/HF
ASTM A216-WCB/HF
ASTM A351-CF8M/A276-316
ASTM A182-316
ASTM A216-WCB
ASTM A194-2H
ASTM A193-B7
ASTM A276-410
ASTM A276-410
ASTM A216-WCB
ASTM A36
ASTM A307-B
ASTM A194-2H
Stainless Steel 304
ASTM A439-D2
ASTM A536 (65-45-12)
ASTM A536 (65-45-12)
ASTM A536 (65-45-12)
ASTM A193-B6
ASTM A276-410
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
ASTM A276-316
Class 900
Size
A-RF
A-BW
A-RTJ
B
C
RF-RTJ Wt.
BW
Wt.
NPS
2
2.5
3
4
6
8
10
12
DN
50
65
75
100
150
200
250
300
In
mm
In
mm
In
mm
In
mm
In
mm
Lbs
Kg
Lbs
Kg
14.5
368
14.5
368
14.62
371
21.7
551
9.8
250
135
61
125
57
16.5
419
16.5
419
16.62
422
26.0
660
9.8
250
175
385
155
70
15.0
381
15.0
381
15.12
384
23.7
602
13.8
350
255
116
213
97
18.0
457
18.0
457
18.12
460
27.6
701
13.8
350
453
206
396
180
24.0
610
24.0
610
24.12
612
38.4
975
22.0
560
913
415
807
367
29.0
737
29.0
737
29.12
740
45.5
1156
25.2
640
1705
775
1465
665
33.0
838
33.0
838
33.12
841
52.6
1336
30.0
760
2387
1085
1724
784
38.0
965
38.0
965
38.12
968
59.8
1519
30.0
760
3600
1636
2790
1268
TC9308-3
27
C
B
(open)
vertical handwheel.
A-RF
TC9308-3
A-BW
28
Component
CB2
Body
Seat Rings
Wedge 2” - 3”
Stem
Yoke and Bonnet
*Bonnet Gasket
Bonnet Nuts
Bonnet Studs
Back Seat Bushing
*Packing
Gland
Gland Flange
Gland Bolt Pins
Gland Bolts
Gland Nuts
Nameplate
Nameplate Rivets
Grease Fitting
Stem Nut
Yoke Bushing
Handwheel
Handwheel Nut
Set Screw
Spacer Ring
CB3
CB4/2
ASTM A216-WCB
ASTM A105/HF
ASTM A276-410
ASTM A216-WCB/HF
ASTM A351-CF8M/A276-316
ASTM A216-WCB/ HF
ASTM A182-F6a
ASTM A182-316
ASTM A216-WCB
ASTM A194-2H
ASTM A194-2HM
ASTM A193-B7
ASTM A193-B7M
ASTM A276-410
ASTM A276-316
ASTM A276-410
ASTM A276-316
ASTM A216-WCB
ASTM A36
ASTM A307-B
ASTM A194-2H
Stainless Steel 304
ASTM A439-D2
ASTM A536 (65-45-12)
ASTM A536 (65-45-12)
ASTM A536 (65-45-12)
ASTM A193-B6
ASTM A276-410
Class 1500
Size
A-RF
A-BW
A-RTJ
B
C
RF-RTJ Wt.
BW
Wt.
NPS
2
2.5
3
4
6
8
10
12
DN
50
65
75
100
150
200
250
300
In
mm
In
mm
In
mm
In
mm
In
mm
Lbs
Kg
Lbs
Kg
14.5
368
14.5
368
14.62
371
21.7
551
11.8
300
128
58
106
48
16.5
419
16.5
419
16.62
422
26.0
660
11.8
300
163
74
137
62
18.5
470
18.5
470
18.62
473
28.5
724
15.75
400
209
95
174
79
21.5
546
21.5
546
21.62
549
32.6
828
19.6
500
423
192
352
160
27.8
706
27.8
706
28.0
711
39.3
998
23.6
600
978
445
870
395
32.75
832
32.75
832
33.13
841
48.1
1223
30.0
760
1625
739
1650
750
39.0
991
39.0
991
39.38
1000
66.5
1688
30.0
760
4412
2001
3541
1606
44.5
1130
44.5
1130
45.12
1146
82.3
2090
35.0
889
8414
3816
7080
3211
TC9308-3
29
II. CAST STEEL BOLTED BONNET GLOBE VALVES
Typical Cast Steel Bolted Bonnet Globe Valve Expanded View
18
19
17
10
16
9
14
12
25
2
11
15
13
22
3
20
21
24
22
1
4
23
5
8
6
7
TC9308-3
30
2. Bonnet: Cameron’s NEWCO bonnet assemblies are built to the same standards as the
bodies.
4. Stem: The stem inserts vertically into the disc.
5. Lock Groove: The lock groove receives the split lock ring, which allows the disc nut to
lift the disc during cycling.
6. Split Ring: The split ring allows the disc nut to lift the disc during cycling.
7. Disc: Cameron’s plug type disc is machined to the tightest tolerances to ensure trouble
free shut-off and cycling.
8. Disc Nut: The disc nut, in conjunction with the split lock ring, secures the disc to the
stem.
9. Gland: The gland compresses the packing to create a stem seal above the back seat
10. Gland Flange: The gland flange applies pressure to the gland for accurate packing
compression.
14. Packing: The packing creates a seal above the back seat between the bonnet and
stem.
19. Handwheel Washer: The washer helps to prevent loosening or distributes pressure
evenly.
body.
body.
23. Seat Ring: To ensure a stable shut-off, the seat ring is aligned and seal-welded into
the valve, then precision ground for optimal seating.
24. Disc Guide: The disc guides provide a stable track for keeping the disc aligned with the
seat during cycling.
25. Spacer Ring: The spacer ring assists the packing rings in creating a seal above the back
seat between the bonnet and stem.
TC9308-3
31
C
Optional gear operator and
vertical handwheel.
B
(open)
A-BW
A-RF
TC9308-3
32
Component
CB2
Body
Disc 2” through 4”
Disc 5” and larger
Stem
Bonnet
*Bonnet Gasket
Bonnet Nuts
Bonnet Studs
Back Seat Bushing
*Packing
Gland
Gland Flange
Gland Bolt Pins
Gland Nuts
Gland Bolts
Seat Ring
Split Ring
Nameplate
Nameplate Rivets
Disc Nut
Stem Nut
Handwheel Washer
Handwheel Nut
Handwheel
Spacer Ring
CB3
CB4/2
ASTM A216-WCB
ASTM A276-410
ASTM A216-WCB/HF
ASTM A216-WCB/13% Chrome
ASTM A276-410
ASTM A216-WCB
ASTM A194-2H
ASTM 193-B7
ASTM A276-410
ASTM A276-410
ASTM A276-WCB
ASTM A36
ASTM A194-2H
ASTM A307-B
ASTM A105/HF **
ASTM A276-410
ASTM A666-304
Commercial
ASTM A276-410
ASTM A439-D2
ASTM A36
ASTM A36
ASTM A536 (65-45-12)
N/A
ASTM A276-316
ASTM A216-WCB/316
ASTM A276-316
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
ASTM A276-316
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
Class 150
Size
A-RF
A-BW
B
C
RF
Wt.
BW
Wt.
NPS
2
2.5
3
4
5
6
8
10
12
14
DN
50
65
75
100
125
150
200
250
300
350
In
mm
In
mm
In
mm
In
mm
Lbs
Kg
Lbs
Kg
8.0
203
8.0
203
14.9
378
8.0
203
51
23
51
23
8.5
216
8.5
216
15.8
401
10.0
254
73
33
73
33
9.5
241
9.5
241
16.6
422
10.0
254
93
42
93
42
11.5
292
11.5
292
19.9
505
12.0
305
137
62
137
62
14.0
356
14.0
356
21.8
554
14.0
356
192
87
192
87
16.0
406
16.0
406
22.4
569
16.0
406
243
110
243
110
19.5
495
19.5
495
26.5
673
18.0
457
419
190
419
190
24.5
622
24.5
622
30.6
777
22.0
559
507
276
507
276
27.5
699
27.5
699
34.8
884
24.0
610
948
476
948
476
31.0
787
31.0
787
41.4
1052
25.2
640
1276
625
1276
625
TC9308-3
33
Tested in Accordance With: API 598 and API RP591
Recommended Spare Parts**
C
vertical handwheel.
B
(open)
A-BW
A-RF
TC9308-3
34
Component
CB2
Body
Stem
Bonnet
*Bonnet Gasket
Bonnet Nuts
Bonnet Studs
Back Seat Bushing
*Packing
Gland
Gland Flange
Gland Bolt Pins
Gland Nuts
Gland Bolts
Seat Ring
Split Ring
Nameplate
Nameplate Rivets
Disc Nut
Stem Nut
Handwheel Washer
Handwheel Nut
Handwheel
Spacer Ring
CB3
CB4/2
ASTM A216-WCB
ASTM A276-410
ASTM A216-WCB/HF
ASTM A216-WCB/ 13% Chrome
ASTM A276-410
ASTM A216-WCB
ASTM A194-2H
ASTM 193-B7
ASTM A276-410
Graphite W/Braided Carbon Fiber End Rings
ASTM A276-410
ASTM A276-WCB
ASTM A36
ASTM A194-2H
ASTM A307-B
ASTM A105/HF**
ASTM A276-410
ASTM A666-304
Commercial
ASTM A276-410
ASTM A439-D2
ASTM A36
ASTM A36
ASTM A536 (65-45-12)
ASTM A276-410
ASTM A276-316
ASTM A216-WCB/316
ASTM A276-316
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
ASTM A276-316
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
Class 300
Size
A-RF
A-BW
B
C
RF
Wt.
BW
Wt.
NPS
2
2.5
3
4
5
6
8
10
12
14
DN
50
65
75
100
125
150
200
250
300
350
In
mm
In
mm
In
mm
In
mm
Lbs
Kg
Lbs
Kg
10.5
267
10.5
267
16.9
429
10.0
254
75.0
34
55
25
11.5
292
11.5
292
17.8
452
10.0
254
100.0
45
79
36
12.5
318
12.5
318
19.2
488
12.0
305
130.0
59
101
46
14.0
357
14.0
357
23.0
584
14.0
356
203.0
92
163
74
15.75
400
15.75
400
27.4
696
14.0
406
294.0
134
242
110
17.5
445
17.5
445
30.6
777
18.0
457
421.0
191
355
161
22.0
559
22.0
559
36.2
919
24.0
610
715
325
566
257
24.5
622
24.5
622
40.8
1036
24.0
610
1015
461
770
350
28.0
711
28.0
711
47.3
1201
27.0
686
1500
682
1218
554
33.0
838
33.0
838
54.3
1379
28.3
720
2446
1112
1996
907
TC9308-3
35
Tested in Accordance With: API 598 and API RP591
Recommended Spare Parts**
C
vertical handwheel.
B
A-RF
TC9308-3
A-BW
36
Component
Body
Stem
Bonnet
*Bonnet Gasket
Bonnet Nuts
Bonnet Studs
Back Seat Bushing
*Packing
Gland
Gland Flange
Gland Bolt Pins
Gland Nuts
Gland Bolts
Seat Ring
Split Ring
Nameplate
Nameplate Rivets
Disc Nut
Stem Nut
Handwheel Washer
Handwheel Nut
Handwheel
Spacer Ring
CB2
CB3
CB4/2
ASTM A216-WCB
ASTM A276-410
ASTM A216-WCB/HF
ASTM A276-410
ASTM A216-WCB
ASTM A194-2H
ASTM 193-B7
ASTM A276-410
ASTM A276-410
ASTM A276-WCB
ASTM A36
ASTM A194-2H
ASTM A307-B
Integral ASTM A216-WCB/HF
ASTM A276-410
ASTM A666-304
Commercial
ASTM A276-410
ASTM A439-D2
ASTM A36
ASTM A36
ASTM A536 (65-45-12)
ASTM A276-410
ASTM A276-316
ASTM A216-WCB/316
ASTM A276-316
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
ASTM A276-316
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
Class 600
Size
A-RF
A-BW
B
C
RF
Wt.
BW
Wt.
NPS
2
2.5
3
4
6
8
DN
50
65
75
100
150
200
In
mm
In
mm
In
mm
In
mm
Lbs
Kg
Lbs
Kg
11.5
292
11.5
292
18.4
467
10.0
254
90
41
79
36
13.0
325
13.0
325
20.0
508
10.0
254
130
59
110
50
14.0
256
14.0
256
24.4
620
14.0
356
170
77
141
64
17.0
435
17.0
435
29.0
737
18.0
457
313
142
256
116
22.0
559
22.0
559
37.9
963
24.0
610
778
354
640
291
26.0
660
26.0
660
44.7
1135
24.0
610
1245
566
961
437
TC9308-3
37
C
vertical handwheel.
B
A-RF
TC9308-3
A-BW
38
Component
CB2
Body
Stem
Bonnet
*Bonnet Gasket
Bonnet Nuts
Bonnet Studs
Back Seat Bushing
*Packing
Gland
Gland Flange
Gland Bolt Pins
Gland Nuts
Gland Bolts
Seat Ring
Split Ring
Nameplate
Nameplate Rivets
Disc Nut
Stem Nut
Handwheel Washer
Handwheel Nut
Handwheel
Spacer Ring
CB3
CB4/2
ASTM A216-WCB
ASTM A276-410
ASTM A216-WCB/HF
ASTM A276-410
ASTM A216-WCB
ASTM A194-2H
ASTM 193-B7
ASTM A276-410
ASTM A276-410
ASTM A276-WCB
ASTM A36
ASTM A194-2H
ASTM A307-B
ASTM A276-410
ASTM A666-304
Commercial
ASTM A276-410
ASTM A439-D2
ASTM A36
ASTM A36
ASTM A536 (65-45-12)
ASTM A276-410
ASTM A276-316
ASTM A216-WCB/316
ASTM A276-316
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
ASTM A276-316
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
Class 900
Size
A-RF
A-BW
B
C
RF
Wt.
BW
Wt.
NPS
2
3
4
6
8
DN
50
75
100
150
200
In
mm
In
mm
In
mm
In
mm
Lbs
Kg
Lbs
Kg
14.5
368
14.5
368
22.6
574
13.8
350
198
90
176
80
15.0
381
15.0
381
26.0
660
17.7
450
335
152
297
135
18.0
457
18.0
457
30.6
777
17.7
450
440
200
376
171
24.0
610
24.0
610
39.6
1006
22.0
560
1675
761
1144
520
29.0
737
29.0
737
60.1
1527
28.3
720
2090
950
1634
743
TC9308-3
39
C
vertical handwheel.
B
A-RF
TC9308-3
A-BW
40
Component
CB2
Body
Stem
Bonnet
*Bonnet Gasket
Bonnet Nuts
Bonnet Studs
Back Seat Bushing
*Packing
Gland
Gland Flange
Gland Bolt Pins
Gland Nuts
Gland Bolts
Seat Ring
Split Ring
Nameplate
Nameplate Rivets
Disc Nut
Stem Nut
Handwheel Washer
Handwheel Nut
Handwheel
Spacer Ring
CB3
CB4/2
ASTM A216-WCB
ASTM A276-410
ASTM A216-WCB/HF
ASTM A276-410
ASTM A216-WCB
ASTM A194-2H
ASTM 193-B7
ASTM A276-410
ASTM A276-410
ASTM A276-WCB
ASTM A36
ASTM A194-2H
ASTM A307-B
ASTM A276-410
ASTM A666-304
Commercial
ASTM A276-410
ASTM A439-D2
ASTM A36
ASTM A36
ASTM A536 (65-45-12)
ASTM A276-410
ASTM A276-316
ASTM A216- WCB/316
ASTM A276-316
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
ASTM A276-316
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
Class 1500
Size
A-RF
A-BW
B
C
RF
Wt.
BW
Wt.
NPS
2
3
4
6
DN
50
75
100
150
In
mm
In
mm
In
mm
In
mm
Lbs
Kg
Lbs
Kg
14.5
368
14.5
368
19.6
498
13.8
350
209
95
143
65
18.5
470
18.5
470
25.6
650
17.7
450
551
250
460
209
21.5
546
21.5
546
30.8
782
19.7
500
959
436
830
377
27.75
705
27.75
705
36.5
927
25.2
640
1191
541
996
453
TC9308-3
41
III. CAST STEEL BOLTED BONNET ANGLE VALVES
Typical Cast Steel Bolted Bonnet Angle Valve Expanded View
18
19
17
10
16
9
14
12
25
2
11
15
13
22
3
20
21
24
22
1
4
23
5
8
6
7
TC9308-3
42
bodies.
5. Lock Groove: The lock groove receives the split lock ring which allows the disc nut to
lift the disc during cycling.
6. Split Ring: The split ring allows the disc nut to lift the disc during cycling.
7. Disc: The disc is machined to the tightest tolerances to ensure trouble free shut-off and
cycling.
8. Disc Nut: The disc nut, in conjunction with the split lock ring, secures the disc to the
stem.
10. Gland Flange: The gland flange applies pressure to the gland for accurate packing
compression.
stem.
evenly.
body.
body.
23. Seat Ring: To ensure a stable shut-off, the seat rings are aligned and seal-welded into
TC9308-3
43
C
B
(open)
D
A
TC9308-3
44
Component
Body
Seat Ring
Disc Nut
Stem
*Bonnet Gasket
Bonnet
Bonnet Studs
Bonnet Nuts
Back Seat Bushing
Packing
Gland Bolt Pins
Gland Bolts
Gland
Gland Flange
Gland Nuts
Stem Nut
Split Ring
Handwheel Washer
Handwheel Nut
Handwheel
Spacer Ring
CB2
CB3
CB4/2
ASTM A216 GR.WCB
ASTM A105/HF
ASTM A276-410
ASTM A216-WCB/HF
ASTM A276-410
ASTM A276-410
ASTM A216-WCB
ASTM 193-B7
ASTM A194-2H
ASTM A276-410
ASTM A36
ASTM 193-B7
ASTM A276-410
ASTM A216-WCB
ASTM A194-2H
ASTM A439-D2
ASTM A276-410
ASTM A36
ASTM A36
ASTM A539 Type (65-45-12)
ASTM A276-410
ASTM A276-316
ASTM A216-WCB/316
ASTM A276-316
ASTM A276-316
ASTM A193-B7M
ASTM A194-2HM
ASTM A276-316
ASTM A193-B7M
ASTM A276-316
ASTM A194-2HM
ASTM A276-316
Class 150
Size
A
B
C
D
RF Wt.
NPS
2
3
4
6
8
DN
In
mm
In
mm
In
mm
In
mm
Lbs
Kg
10
12
50
75
100
150
200
250
300
4.0
107
15.2
386
8
203
6
152
57
26
4.75
121
16.9
429
10
254
7.5
191
84
38
5.75
146
20.4
518
12
305
9
229
141
64
8.0
203
21.8
554
15
381
11
279
234
106
9.75
248
27.4
696
18
457
13.5
343
399
181
12.25
311
31
787
22
559
16
406
611
278
13.75
349
37.8
960
24
610
19
483
794
361
TC9308-3
45
C
B
(open)
D
A
TC9308-3
46
Component
Body
Seat Ring
Disc Nut
Stem
*Bonnet Gasket
Bonnet
Bonnet Studs
Bonnet Nuts
Back Seat Bushing
Packing
Gland Bolt Pins
Gland Bolts
Gland
Gland Flange
Gland Nuts
Stem Nut
Split Ring
Handwheel Washer
Handwheel Nut
Handwheel
Spacer Ring
CB2
CB3
CB4/2
ASTM A216 GR.WCB
ASTM A105/HF
ASTM A276-410
ASTM A216-WCB/HF
ASTM A276-410
ASTM A276-410
ASTM A216-WCB
ASTM 193-B7
ASTM A194-2H
ASTM A276-410
ASTM A36
ASTM 193-B7
ASTM A276-410
ASTM A216-WCB
ASTM A194-2H
ASTM A439-D2
ASTM A276-410
ASTM A36
ASTM A36
ASTM A539 Type (65-45-12)
ASTM A276-410
ASTM A276-316
ASTM A216-WCB/316
ASTM A276-316
ASTM A276-316
ASTM A193-B7M
ASTM A194-2HM
ASTM A276-316
ASTM A193-B7M
ASTM A276-316
ASTM A194-2HM
ASTM A276-316
Class 300
Size
A
B
C
D
RF Wt.
NPS
2
3
4
6
8
10
12
DN
50
75
100
150
200
250
300
In
mm
In
mm
In
mm
In
mm
Lbs
Kg
5.25
133
15
381
10
254
6.5
165
68
31
6.25
159
16.9
429
12
305
8.25
210
108
49
7
178
21.7
551
14
356
10
254
198
90
8.75
222
28
711
17
432
12.5
318
392
178
11
279
30.7
780
24
610
15
381
560
255
12.25
311
37.5
953
24
610
17.5
445
934
425
14
356
41.6
1049
27
686
20.5
521
1288
586
TC9308-3
47
C
B
(open)
D
A
TC9308-3
48
Component
Body
Seat Ring
Disc Nut
Stem
*Bonnet Gasket
Bonnet
Bonnet Studs
Bonnet Nuts
Back Seat Bushing
Packing
Gland Bolt Pins
Gland Bolts
Gland
Gland Flange
Gland Nuts
Stem Nut
Split Ring
Handwheel Washer
Handwheel Nut
Handwheel
Spacer Ring
CB2
CB3
CB4/2
ASTM A216 GR.WCB
ASTM A105/HF
ASTM A276-410
ASTM A216-WCB/HF
ASTM A276-410
ASTM A276-410
ASTM A216-WCB
ASTM 193-B7
ASTM A194-2H
ASTM A276-410
ASTM A36
ASTM 193-B7
ASTM A276-410
ASTM A216-WCB
ASTM A194-2H
ASTM A439-D2
ASTM A276-410
ASTM A36
ASTM A36
ASTM A539 Type (65-45-12)
ASTM A276-410
ASTM A276-316
ASTM A216-WCB/316
ASTM A276-316
ASTM A276-316
ASTM A193-B7M
ASTM A194-2HM
ASTM A276-316
ASTM A193-B7M
ASTM A276-316
ASTM A194-2HM
ASTM A276-316
Class 600
Size
A
B
C
D
RF Wt.
NPS
2
2.5
3
4
6
8
DN
50
75
100
150
200
250
In
mm
In
mm
In
mm
In
mm
Lbs
Kg
5.75
146
18.9
480
8.8
224
6.5
165
79
36
6.5
165
20.9
531
9.8
249
7.5
191
110
50
7.0
178
19.8
503
11.0
279
8.3
211
141
64
8.5
216
22.2
564
14.0
356
9.0
229
256
116
11.0
279
28.2
716
17.7
450
14.0
356
640
291
13.0
330
38.5
978
24.8
630
16.5
419
961
437
TC9308-3
49
IV. CAST STEEL BOLTED COVER SWING CHECK VALVES
Typical Cast Steel Bolted Cover Swing Check Valve Expanded View
13
12
2
3
11
12
1
6
4
8
9
7
5
10
TC9308-3
50
Note: Classes 150 and 300 use external hinge pin.
2. Cover: The cover allows access to internal components.
3. Cover Gasket: The cover gasket creates a leakproof seal between the bonnet and body.
4. Seat Ring: To ensure a stable shut-off, the seat ring is aligned and seal-welded into the
5. Disc: The disc allows unidirectional flow and restricts back flow with trouble free shutoff.
6. Swing Arm: The swing arm allows the disc to open and close.
7. & 8. Disc Nut and Pin: The disc nut and pin secure the disc to the swing arm.
9. Hinge Pin: The hinge pin provides a stable mechanism for the swing arm to operate.
10. Plug: The plug secures the arm pin inside the valve.
11. Plug Gasket: The plug gasket creates a leak-proof seal between the plug and body.
12. & 13. Cover Studs and Nuts: The cover studs and nuts secure the bonnet to the body.
14. Eyebolt: The eyebolt is use to aid in lifting the valve.
TC9308-3
51
Hinge pin and
plug details
Eye bolts are on
sizes 5” and larger
B
Center of Port
B
A-RF
TC9308-3
A-BW
52
Component
CB2
Body
Cover
Swing Arm
Seat Ring
*Cover Gasket
Hinge Pin
Name Plate
Plug Gasket
Cover Bolt
Cover Nut
Plug
Disc Pin
Disc Nut
Eye Bolt 5” through 24”
CB3
CB4/2
ASTM A216-WCB
ASTM A105N
ASTM A182-F6a
ASTM A182-F6a/HF
ASTM A182-F316
ASTM A216-WCB/HF
ASTM A216-WCB/316 Faced
ASTM A216-WCB
ASTM A105/HF
ASTM A276-410
ASTM A276-316
304 Stainless Steel
Stainless Steel
ASTM A193-B7
ASTM A193-B7M
AISI 1020
ASTM A276-410
ASTM A276-316
ASTM A276-316
A194-8
Carbon Steel
Class 150
Size
A-RF
A-BW
B
RF Wt.
BW Wt.
NPS
2
2.5
3
4
5
6
8
10
12
14
16
18
20
24
DN
50
75
100
150
125
150
200
250
300
350
400
450
500
600
In
mm
In
mm
In
mm
Lbs
Kg
Lbs
Kg
8.0
203
8.0
203
6.8
173
36
16
29
13
8.5
216
8.5
216
7.4
188
51
23
38
17
9.5
241
9.5
241
7.7
196
64
29
49
22
11.5
292
11.5
292
8.5
216
98
45
73
33
13.0
330
13.0
330
12.3
315
135
61
110
50
14.0
356
14.0
356
12.8
325
181
398
146
66
19.5
495
19.5
495
14.3
363
298
135
243
110
24.5
622
24.5
622
17.2
437
463
210
421
191
27.5
699
27.5
699
17.9
455
688
313
591
269
31.0
787
31.0
787
19.6
498
898
408
766
348
34.0
864
34.0
864
21.2
538
1147
521
979
445
38.5
978
38.5
978
24.2
615
1367
621
1190
541
38.5
978
38.5
978
27.4
696
1808
822
1585
720
51.0
1295
51.0
1295
30.0
762
2866
1308
2250
1123
TC9308-3
53
Hinge pin and
plug details
Eye bolts are on
B
Center of Port
B
A-RF
TC9308-3
A-BW
54
Component
CB2
Body
Cover
Swing Arm
Seat Ring
*Cover Gasket
Hinge Pin
Name Plate
Plug Gasket
Cover Bolt
Cover Nut
Plug
Disc Pin
Disc Nut
CB3
CB4/2
ASTM A216-WCB
ASTM A105N
ASTM A182-F6a
ASTM A182-F6a/HF
ASTM A182-F316
ASTM A216-WCB/HF
ASTM A216-WCB
ASTM A105/HF
ASTM A276-410
ASTM A276-316
304 Stainless Steel
Stainless Steel
ASTM A193-B7
ASTM A193-B7M
ASTM A276-410
ASTM A276-316
AISI 1020
ASTM A276-316
A194-8
Carbon Steel
Class 300
Size
A-RF
A-BW
B
RF Wt.
BW Wt.
NPS
2
2.5
3
4
5
6
8
10
12
14
16
18
20
24
DN
50
75
100
150
125
150
200
250
300
350
400
450
500
600
In
mm
In
mm
In
mm
Lbs
Kg
Lbs
Kg
10.5
267
10.5
267
7.6
193
58
26
44
20
11.5
292
11.5
292
8.3
211
86
39
55
25
12.5
318
12.5
318
8.9
226
95
43
78
35
14.0
356
14.0
356
9.8
249
144
65
103
47
15.75
400
15.75
400
13.3
338
232
105
185
84
17.5
445
17.5
445
14.0
356
283
129
214
97
21.0
533
21.0
533
15.9
404
433
197
341
155
24.5
622
24.5
622
18.7
475
694
315
562
255
28.0
711
28.0
711
21.9
556
1003
456
815
370
33.0
838
33.0
838
23.1
587
1345
611
1087
494
34.0
864
34.0
864
25.2
640
1720
782
1397
635
38.5
978
38.5
978
28.6
726
2271
1032
1873
851
40.0
1016
40.0
1016
30.2
767
2888
1313
2400
1091
53.0
1346
53.0
1346
33.6
853
4718
2145
3995
1816
TC9308-3
55
Eye bolts are on
B
Center of Port
B
A-RF
TC9308-3
A-BW
56
Component
CB2
Body
Cover
Swing Arm
Seat Ring
*Cover Gasket
Hinge Pin
Name Plate
Washer
Cover Bolt
Cover Nut
Plug
Pin
Hex Nut
CB3
CB4/2
ASTM A216-WCB
ASTM A105N
ASTM A182-F6a
ASTM A182-F6a/HF
ASTM A216-WCB/HF
ASTM A216-WCB
ASTM A105/HF
ASTM A276-410
304 Stainless Steel
Stainless Steel
ASTM A193-B7
ASTM A276-410
AISI 1020
ASTM A276-316
A194-8
Carbon Steel
ASTM A182-F316
ASTM A276-316
ASTM A193-B7M
ASTM A276-316
Class 600
Size
A-RF
A-BW
B
RF Wt.
BW Wt.
NPS
2
2.5
3
4
5
6
8
10
12
14
DN
50
75
100
150
125
150
200
250
300
350
In
mm
In
mm
In
mm
Lbs
Kg
Lbs
Kg
11.5
292
11.5
292
7.8
198
65
30
51
23
13.0
330
13.0
330
8.8
224
90
41
68
31
14.0
356
14.0
356
9.7
246
115
52
91
41
17.0
432
17.0
432
13.3
338
215
98
161
73
20.0
508
20.0
508
15.5
394
348
159
255
116
22.0
559
22.0
559
16.8
427
481
219
349
159
26.0
660
26.0
660
19.4
493
926
421
762
346
31.0
787
31.0
787
22.6
574
1279
581
1021
483
33.0
838
33.0
838
25.4
645
1722
783
1411
641
35.0
889
35.0
889
26.4
671
2009
913
1650
750
TC9308-3
57
Eye bolts are on
B
Center of Port
B
A-RF
TC9308-3
A-BW
58
Component
CB2
Body
Cover
Swing Arm
Seat Ring
*Cover Gasket
Hinge Pin
Name Plate
Washer
Cover Bolt
Cover Nut
Plug
Pin
Hex Nut
CB3
ASTM A216-WCB
ASTM A105N
ASTM A182-F6a
ASTM A182-F6a/HF
ASTM A216-WCB/HF
ASTM A216-WCB
ASTM A105/HF
ASTM A276-410
304 Stainless Steel
Stainless Steel
ASTM A193-B7
ASTM A276-410
AISI 1020
ASTM A276-316
A194-8
Carbon Steel
CB4/2
ASTM A182-F316
ASTM A276-316
ASTM A193-B7M
ASTM A276-316
Class 900
Size
A-RF
A-BW
B
RF Wt.
BW Wt.
NPS
2
3
4
6
8
DN
50
75
100
150
200
In
mm
In
mm
In
mm
Lbs
Kg
Lbs
Kg
14.5
368
14.5
368
13.1
329
104
47
78
35
15.0
381
15.0
381
14.8
329
184
84
138
63
18.0
457
18.0
457
14.5
368
344
156
258
129
24.0
610
24.0
610
18.8
478
770
350
578
263
29.0
737
29.0
737
23.6
599
1482
674
1112
505
TC9308-3
59
Eye bolts are on
B
Center of Port
B
A-RF
TC9308-3
A-BW
60
Component
Body
Cover
Swing Arm
Seat Ring
*Cover Gasket
Hinge Pin
Name Plate
Washer
Cover Bolt
Cover Nut
Plug
Pin
Hex Nut
CB2
CB3
CB4/2
ASTM A216-WCB
ASTM A105N
ASTM A182-F6a
ASTM A182-F6a/HF
ASTM A216-WCB/HF
ASTM A216-WCB
ASTM A105/HF
ASTM A276-410
304 Stainless Steel
Stainless Steel
ASTM A193-B7
ASTM A276-410
AISI 1020
ASTM A276-316
A194-8
Carbon Steel
ASTM A182-F316
ASTM A276-316
ASTM A193-B7M
ASTM A276-316
Class 1500
Size
A-RF
A-BW
B
RF Wt.
BW Wt.
NPS
2
2.5
3
4
6
8
DN
50
75
100
150
200
203
In
mm
In
mm
In
mm
Lbs
Kg
Lbs
Kg
14.5
368
14.5
368
13.1
333
165
75
153
70
16.5
419
16.5
419
13.7
348
243
110
223
101
18.5
470
18.5
470
14.8
376
284
129
256
116
21.5
546
21.5
546
15.2
386
462
269
425
193
27.8
706
27.8
706
19.2
488
940
427
895
407
32.8
833
32.8
833
27.0
686
1030
468
985
448
TC9308-3
61
V.CAST STEEL BOLTED COVER TILTING DISC CHECK VALVES
(PRESSURE SEAL 600 TO 2500)
Typical Cast Steel Bolted Cover Tilting Disc Check Valve Expanded View
12
11
2
3
10
7
6
1
5
4
9
6
8
7
TC9308-3
62
Note: Classes 600 and larger use internal hinge pin.
2. Cover: The cover allows access to internal components.
3. Cover Gasket: The cover gasket creates a leak-proof seal between the bonnet and
body.
4. Seat Ring: To ensure a stable shut-off, the seat ring is aligned and seal-welded into the
5. Disc: The disc allows unidirectional flow and restricts back flow with trouble free shutoff.
6. Plug Gasket: The plug gasket creates a leak-proof seal between the plug and body.
7. Plug: The disc nut and pin secures the disc to the arm.
8. Hinge Pin: The hinge pin provides a stable mechanism for the disc to operate.
9. Hinge Pin Washer: The hinge pin washer provides accurate disc positioning.
10. & 11. Cover Studs and Nuts: The cover studs and nuts secure the bonnet to the body.
12. Eyebolt: The eyebolt is used to aid in lifting the valve.
TC9308-3
63
Class: 150 - Sizes: 2.5” to 12”
Pressure Class Range: 150 to 300 (See Pressure Seal To 2500)
Eye bolts are on
Hinge pin, plug, and
gasket details
B
Center of Port
B
A-RF
TC9308-3
A-BW
64
Component
CB2
CB3
Body
Cover
CB4/2
ASTM A216-WCB
ASTM A105/A216-WCB
Disc
Seat Ring
ASTM A182-F316/
ASTM A351-CF8M
ASTM A182-F316/
ASTM A351-CF8M w/HF
ASTM A216-WCB/HF
ASTM A105/HF
*Cover Gasket
Hinge Pin
Hinge Pin Washer
Plug Gasket
Name Plate
Cover Bolts
Cover Nuts
Plug
Eye Bolt 5” and larger
ASTM A479-410
ASTM A479-410
304 Stainless Steel/Graphite
304 Stainless Steel
ASTM A193-B7
ASTM A194-2H
ASTM A105
ASTM A108-1020
ASTM A193-B7M
ASTM A194-2HM
Class 150
Size
A-RF
A-BW
B
RF Wt.
BW Wt.
NPS
2.5
3
4
6
8
10
12
DN
65
75
100
150
200
250
300
In
mm
In
mm
In
mm
Lbs
Kg
Lbs
Kg
8.5
216
8.5
216
8.27
210
42
92
30
66
9.5
241
9.5
241
7.5
190
68
150
50
110
11.5
292
11.5
292
7.3
185
92
202
78
172
14.0
356
14.0
356
9.0
230
174
383
136
299
19.5
495
19.5
495
13.8
350
302
664
244
537
24.5
622
24.5
622
15.4
390
477
1049
376
827
27.5
699
27.5
699
16.1
410
655
1441
464
1021
TC9308-3
65
Pressure Class Range: 150 to 300 (See Pressure Seal To 2500)
Eye bolts are on
Hinge pin, plug, and
gasket details
B
Center of Port
B
A-RF
TC9308-3
A-BW
66
Component
CB2
CB3
Body
Cover
CB4/2
ASTM A216-WCB
ASTM A105/A216-WCB
Disc
Seat Ring
ASTM A216-WCB/HF
ASTM A105/HF
*Cover Gasket
Hinge Pin
Hinge Pin Washer
Plug Gasket
Name Plate
Cover Bolts
Cover Nuts
Plug
Eye Bolt 5” and larger
ASTM A479-410
ASTM A479-410
304 Stainless Steel/Graphite
304 Stainless Steel
ASTM A193-B7
ASTM A194-2H
ASTM A105
ASTM A108-1020
ASTM A182-F316/
ASTM A351-CF8M
ASTM A182-F316/
ASTM A351-CF8M w/HF
ASTM A193-B7M
ASTM A194-2HM
Class 300
Size
A-RF
A-BW
B
RF Wt.
BW Wt.
NPS
3
4
6
8
10
12
DN
75
100
150
200
250
300
In
mm
In
mm
In
mm
Lbs
Kg
Lbs
Kg
12.5
318
12.5
318
6.5
165
82
180
57
125
14.0
356
14.0
356
7.3
185
122
268
78
172
17.5
444
17.5
444
8.8
224
252
554
168
370
21.0
533
21.0
533
13.4
340
386
849
278
612
24.5
622
24.5
622
15.2
385
568
1250
458
1008
28.0
711
28.0
711
17.7
450
818
1800
690
1518
TC9308-3
67
VI. CAST STEEL BOLTED BONNET STOP CHECK VALVES
Typical Cast Steel Bolted Bonnet Stop Check Valve Expanded View
16
17
15
14
8
7
10
12
2
9
13
11
20
3
18
19
22
20
1
4
21
6
Vent
TC9308-3
5
68
bodies.
3. Back Seat: The back seat, when engaged with the stem head, provides a stable shut-off
to the stuffing box which isolates the packing from flow exposure.
5. Disc: The 1-piece vented disc is machined to the tightest tolerance to ensure trouble
free shut-off and cycling.
6. Disc Nut: The disc nut serves as a mechanical guide acting on the stem to ensure proper
alignment of the disc to the seat.
stem.
evenly.
body.
body.
TC9308-3
69
C
vertical handwheel.
B
(open)
A-BW
A-RF
TC9308-3
70
Component
CB2
Body
Stem
Bonnet
*Bonnet Gasket
Bonnet Nuts
Bonnet Studs
Back Seat Bushing
*Packing
Gland
Gland Flange
Gland Bolt Pins
Gland Nuts
Gland Bolts
Seat Ring
Split Ring
Nameplate
Nameplate Rivets
Disc Nut
Stem Nut
Handwheel Washer
Handwheel Nut
Handwheel
Spacer Ring
CB3
CB4/2
ASTM A216-WCB
ASTM A276-410
ASTM A216-WCB/HF
ASTM A276-410
ASTM A216-WCB
ASTM A194-2H
ASTM 193-B7
ASTM A276-410
ASTM A276-410
ASTM A276-WCB
ASTM A36
ASTM A194-2H
ASTM A307-B
ASTM A105/HF**
N/A
ASTM A666-304
Commercial
ASTM A276-410
ASTM A439-D2
ASTM A36
ASTM A36
ASTM A536 (65-45-12)
N/A
ASTM A276-316
ASTM A216-WCB/316
ASTM A276-316
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
ASTM A276-316
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
Class 150
Size
A-RF
A-BW
B
C
RF Wt.
BW Wt.
NPS
2
2.5
3
4
5
6
8
10
12
14
DN
50
75
100
150
125
150
200
250
300
350
In
mm
In
mm
In
mm
In
mm
Lbs
Kg
Lbs
Kg
8.0
203
8.0
203
14.9
378
8.0
203
51
23
51
23
8.5
216
8.5
216
15.8
401
10.0
254
73
33
73
33
9.5
241
9.5
241
16.6
422
10.0
254
93
42
93
42
11.5
292
11.5
292
19.9
505
12.0
305
137
62
137
62
14.0
356
14.0
356
21.8
554
14.0
356
192
87
192
87
16.0
406
16.0
406
22.4
569
16.0
406
243
110
243
110
19.5
495
19.5
495
26.5
673
18.0
457
419
190
419
190
24.5
622
24.5
622
30.6
777
22.0
559
507
276
507
276
27.5
699
27.5
699
34.8
884
24.0
610
948
476
948
476
31.0
787
31.0
787
41.4
1052
25.2
640
1276
625
1276
625
** Integral seat w/HF for sizes 2” to 4”.
TC9308-3
71
C
vertical handwheel.
B
(open)
A-BW
A-RF
TC9308-3
72
Component
CB2
Body
Stem
Bonnet
*Bonnet Gasket
Bonnet Nuts
Bonnet Studs
Back Seat Bushing
*Packing
Gland
Gland Flange
Gland Bolt Pins
Gland Nuts
Gland Bolts
Seat Ring
Split Ring
Nameplate
Nameplate Rivets
Disc Nut
Stem Nut
Handwheel Washer
Handwheel Nut
Handwheel
Spacer Ring
CB3
CB4/2
ASTM A216-WCB
ASTM A276-410
ASTM A216-WCB/HF
ASTM A276-410
ASTM A216-WCB
ASTM A194-2H
ASTM 193-B7
ASTM A276-410
ASTM A276-410
ASTM A276-WCB
ASTM A36
ASTM A194-2H
ASTM A307-B
ASTM A105/HF**
N/A
ASTM A666-304
Commercial
ASTM A276-410
ASTM A439-D2
ASTM A36
ASTM A36
ASTM A536 (65-45-12)
N/A
ASTM A276-316
ASTM A216-WCB/316
ASTM A276-316
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
ASTM A276-316
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
Class 300
Size
A-RF
A-BW
B
C
RF Wt.
BW Wt.
NPS
2
2.5
3
4
5
6
8
10
12
14
DN
50
75
100
150
125
150
200
250
300
350
In
mm
In
mm
In
mm
In
mm
Lbs
Kg
Lbs
Kg
10.5
267
10.5
267
16.9
429
10.0
254
75.0
34
55
25
11.5
292
11.5
292
17.8
452
10.0
254
100.0
45
79
36
12.5
318
12.5
318
19.2
488
12.0
305
130.0
59
101
46
14.0
357
14.0
357
23.0
584
14.0
356
203.0
92
163
74
15.75
400
15.75
400
27.4
696
14.0
406
294.0
134
242
110
17.5
445
17.5
445
30.6
777
18.0
457
421.0
191
355
161
22.0
559
22.0
559
36.2
919
24.0
610
715
325
566
257
24.5
622
24.5
622
40.8
1036
24.0
610
1015
461
770
350
28.0
711
28.0
711
47.3
1201
27.0
686
1500
682
1218
554
33.0
838
33.0
838
54.3
1379
28.3
720
2446
1112
1996
907
** Integral seat w/HF for sizes 2” to 4”.
TC9308-3
73
C
vertical handwheel.
B
A-RF
TC9308-3
A-BW
74
Component
Body
Stem
Bonnet
*Bonnet Gasket
Bonnet Nuts
Bonnet Studs
Back Seat Bushing
*Packing
Gland
Gland Flange
Gland Bolt Pins
Gland Nuts
Gland Bolts
Seat Ring
Split Ring
Nameplate
Nameplate Rivets
Disc Nut
Stem Nut
Handwheel Washer
Handwheel Nut
Handwheel
Spacer Ring
CB2
CB3
CB4/2
ASTM A216-WCB
ASTM A276-410
ASTM A216-WCB/HF
ASTM A276-410
ASTM A216-WCB
ASTM A194-2H
ASTM 193-B7
ASTM A276-410
ASTM A276-410
ASTM A276-WCB
ASTM A36
ASTM A194-2H
ASTM A307-B
Integral ASTM A216 WCB/HF
N/A
ASTM A666-304
Commercial
ASTM A276-410
ASTM A439-D2
ASTM A36
ASTM A36
ASTM A536 (65-45-12)
ASTM A276-410
ASTM A276-316
ASTM A216-WCB/316
ASTM A276-316
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
ASTM A276-316
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
Class 600
Size
A-RF
A-BW
B
C
RF Wt.
BW Wt.
NPS
2
2.5
3
4
6
8
DN
50
75
100
150
200
203
In
mm
In
mm
In
mm
In
mm
Lbs
Kg
Lbs
Kg
11.5
292
11.5
292
18.4
467
10.0
254
90
41
79
36
13.0
325
13.0
325
20.0
508
10.0
254
130
59
110
50
14.0
256
14.0
256
24.4
620
14.0
356
170
77
141
64
17.0
435
17.0
435
29.0
737
18.0
457
313
142
256
116
22.0
559
22.0
559
37.9
963
24.0
610
778
354
640
291
26.0
660
26.0
660
44.7
1135
24.0
610
1245
566
961
437
TC9308-3
75
C
vertical handwheel.
B
A-RF
TC9308-3
A-BW
76
Component
CB2
Body
Stem
Bonnet
*Bonnet Gasket
Bonnet Nuts
Bonnet Studs
Back Seat Bushing
*Packing
Gland
Gland Flange
Gland Bolt Pins
Gland Nuts
Gland Bolts
Seat Ring
Split Ring
Nameplate
Nameplate Rivets
Disc Nut
Stem Nut
Handwheel Washer
Handwheel Nut
Handwheel
Spacer Ring
CB3
CB4/2
ASTM A216-WCB
ASTM A276-410
ASTM A216-WCB/HF
ASTM A276-410
ASTM A216-WCB
ASTM A194-2H
ASTM 193-B7
ASTM A276-410
ASTM A276-410
ASTM A276-WCB
ASTM A36
ASTM A194-2H
ASTM A307-B
N/A
ASTM A666-304
Commercial
ASTM A276-410
ASTM A439-D2
ASTM A36
ASTM A36
ASTM A536 (65-45-12)
ASTM A276-410
ASTM A276-316
ASTM A216-WCB/316
ASTM A276-316
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
ASTM A276-316
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
Class 900
Size
A-RF
A-BW
B
C
RF Wt.
BW Wt.
NPS
2
3
4
6
8
DN
50
75
100
150
200
In
mm
In
mm
In
mm
In
mm
Lbs
Kg
Lbs
Kg
14.5
368
14.5
368
22.6
574
13.8
350
198
90
176
80
15.0
381
15.0
381
26.0
660
17.7
450
335
152
297
135
18.0
457
18.0
457
30.6
777
17.7
450
440
200
376
171
24.0
610
24.0
610
39.6
1006
22.0
560
1675
761
1144
520
29.0
737
29.0
737
60.1
1527
28.3
720
2090
950
1634
743
TC9308-3
77
C
vertical handwheel.
B
A-RF
TC9308-3
A-BW
78
Component
CB2
Body
Stem
Bonnet
*Bonnet Gasket
Bonnet Nuts
Bonnet Studs
Back Seat Bushing
*Packing
Gland
Gland Flange
Gland Bolt Pins
Gland Nuts
Gland Bolts
Seat Ring
Split Ring
Nameplate
Nameplate Rivets
Disc Nut
Stem Nut
Handwheel Washer
Handwheel Nut
Handwheel
Spacer Ring
CB3
CB4/2
ASTM A216-WCB
ASTM A276-410
ASTM A216-WCB/HF
ASTM A276-410
A216-WCB
ASTM A194-2H
ASTM 193-B7
ASTM A276-410
ASTM A276-410
ASTM A276-WCB
ASTM A36
ASTM A194-2H
ASTM A307-B
N/A
ASTM A666-304
Commercial
ASTM A276-410
ASTM A439-D2
ASTM A36
ASTM A36
ASTM A536 (65-45-12)
ASTM A276-410
ASTM A276-316
ASTM A216-WCB/316
ASTM A276-316
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
ASTM A276-316
ASTM A194-2HM
ASTM A193-B7M
ASTM A276-316
Class 1500
Size
A-RF
A-BW
B
C
RF Wt.
BW Wt.
NPS
DN
In
mm
In
mm
In
mm
In
mm
Lbs
Kg
Lbs
Kg
2
50
14.5
368
14.5
368
19.6
498
13.8
350
209
95
143
65
3
75
18.5
470
18.5
470
25.6
650
17.7
450
551
250
460
209
4
100
21.5
546
21.5
546
30.8
782
19.7
500
959
436
830
377
6
150
27.75
705
27.75
705
36.5
927
25.2
640
1191
541
996
453
TC9308-3
79
VII. CAST STEEL BOLTED BONNET ANGLE STOP CHECK VALVES
Typical Cast Steel Bolted Bonnet Angle Stop Check Valve Expanded View
16
17
15
8
14
7
12
10
23
2
9
13
11
20
3
18
19
22
20
1
4
21
6
5
TC9308-3
80
bodies.
5. Disc: The 1-piece disc is machined to the tightest tolerance to ensure trouble free shutoff and cycling.
6. Disc Nut: The disc nut serves as a mechanical guide acting on the stem to ensure proper
alignment of the disc to the seat.
stem.
evenly.
body.
body.
TC9308-3
81
C
B
(open)
D
A
TC9308-3
82
Component
Body
Seat Ring
Disc Nut
Stem
*Bonnet Gasket
Bonnet
Bonnet Studs
Bonnet Nuts
Back Seat Bushing
Packing
Gland Bolt Pins
Gland Bolts
Gland
Gland Flange
Gland Nuts
Stem Nut
Split Ring
Handwheel Washer
Handwheel Nut
Handwheel
Spacer Ring
CB2
CB3
CB4/2
ASTM A216 GR.WCB
ASTM A105/HF
ASTM A276-410
ASTM A216-WCB/HF
ASTM A276-410
ASTM A276-410
ASTM A216-WCB
ASTM 193-B7
ASTM A194-2H
ASTM A276-410
ASTM A36
ASTM 193-B7
ASTM A276-410
ASTM A216-WCB
ASTM A194-2H
ASTM A439-D2
ASTM A276-410
ASTM A36
ASTM A36
ASTM A539 Type (65-45-12)
ASTM A276-410
ASTM A276-316
ASTM A216-WCB/316
ASTM A276-316
ASTM A276-316
ASTM A193-B7M
ASTM A194-2HM
ASTM A276-316
ASTM A193-B7M
ASTM A276-316
ASTM A194-2HM
ASTM A276-316
Class 150
Size
A
B
C
D
RF Wt.
NPS
2
3
4
6
8
DN
In
mm
In
mm
In
mm
In
mm
Lbs
Kg
10
12
50
75
100
150
200
250
300
4.0
107
15.2
386
8
203
6
152
57
26
4.75
121
16.9
429
10
254
7.5
191
84
38
5.75
146
20.4
518
12
305
9
229
141
64
8.0
203
21.8
554
15
381
11
279
234
106
9.75
248
27.4
696
18
457
13.5
343
399
181
12.25
311
31
787
22
559
16
406
611
278
13.75
349
37.8
960
24
610
19
483
794
361
TC9308-3
83
C
B
(open)
D
A
TC9308-3
84
Component
Body
Seat Ring
Disc Nut
Stem
*Bonnet Gasket
Bonnet
Bonnet Studs
Bonnet Nuts
Back Seat Bushing
Packing
Gland Bolt Pins
Gland Bolts
Gland
Gland Flange
Gland Nuts
Stem Nut
Split Ring
Handwheel Washer
Handwheel Nut
Handwheel
Spacer Ring
CB2
CB3
CB4/2
ASTM A216 GR.WCB
ASTM A105/HF
ASTM A276-410
ASTM A216-WCB/HF
ASTM A276-410
ASTM A276-410
ASTM A216-WCB
ASTM 193-B7
ASTM A194-2H
ASTM A276-410
ASTM A36
ASTM 193-B7
ASTM A276-410
ASTM A216-WCB
ASTM A194-2H
ASTM A439-D2
ASTM A276-410
ASTM A36
ASTM A36
ASTM A539 Type (65-45-12)
ASTM A276-410
ASTM A276-316
ASTM A216-WCB/316
ASTM A276-316
ASTM A276-316
ASTM A193-B7M
ASTM A194-2HM
ASTM A276-316
ASTM A193-B7M
ASTM A276-316
ASTM A194-2HM
ASTM A276-316
Class 300
Size
A
B
C
D
RF Wt.
NPS
2
3
4
6
8
10
12
DN
50
75
100
150
200
250
300
In
mm
In
mm
In
mm
In
mm
Lbs
Kg
5.25
133
15
381
10
254
6.5
165
68
31
6.25
159
16.9
429
12
305
8.25
210
108
49
7
178
21.7
551
14
356
10
254
198
90
8.75
222
28
711
17
432
12.5
318
392
178
11
279
30.7
780
24
610
15
381
560
255
12.25
311
37.5
953
24
610
17.5
445
934
425
14
356
41.6
1049
27
686
20.5
521
1288
586
TC9308-3
85
C
B
(open)
D
A
TC9308-3
86
Component
Body
Seat Ring
Disc Nut
Stem
*Bonnet Gasket
Bonnet
Bonnet Studs
Bonnet Nuts
Back Seat Bushing
Packing
Gland Bolt Pins
Gland Bolts
Gland
Gland Flange
Gland Nuts
Stem Nut
Split Ring
Handwheel Washer
Handwheel Nut
Handwheel
Spacer Ring
CB2
CB3
CB4/2
ASTM A216 GR.WCB
ASTM A105/HF
ASTM A276-410
ASTM A216-WCB/HF
ASTM A276-410
ASTM A276-410
ASTM A216-WCB
ASTM 193-B7
ASTM A194-2H
ASTM A276-410
ASTM A36
ASTM 193-B7
ASTM A276-410
ASTM A216-WCB
ASTM A194-2H
ASTM A439-D2
ASTM A276-410
ASTM A36
ASTM A36
ASTM A539 Type (65-45-12)
ASTM A276-410
ASTM A276-316
ASTM A216-WCB/316
ASTM A276-316
ASTM A276-316
ASTM A193-B7M
ASTM A194-2HM
ASTM A276-316
ASTM A193-B7M
ASTM A276-316
ASTM A194-2HM
ASTM A276-316
Class 600
Size
A
B
C
D
RF Wt.
NPS
2
2.5
3
4
6
8
DN
50
75
100
150
200
250
In
mm
In
mm
In
mm
In
mm
Lbs
Kg
5.75
146
18.9
480
8.8
224
6.5
165
79
36
6.5
165
20.9
531
9.8
249
7.5
191
110
50
7.0
178
19.8
503
11.0
279
8.3
211
141
64
8.5
216
22.2
564
14.0
356
9.0
229
256
116
11.0
279
28.2
716
17.7
450
14.0
356
640
291
13.0
330
38.5
978
24.8
630
16.5
419
961
437
TC9308-3
87
VIII. HOW TO ORDER ALL CAMERON’S NEWCO PRODUCTS
Figure Number
The figure number shown below identifies specific valve configuration details of
Cameron’s NEWCO valves such as valve type, pressure class, end connections, body/bonnet
and trim materials, and special features.
Please specify end connections, body materials and trims not listed below.
When placing an order, please refer to the respective product section of the catalog for
size availability. A detailed description must be included with any special orders.
TC9308-3
88
Pressure Class
Type
1= Gate, OS&Y
2= Globe/Globe Stop Check, OS&Y
3= Swing/Tilting Disc Check
4= Piston Check
5=Ball
6= Gate, NRS
7= Angle/Angle Stop Check, OS&Y
1=150
2=125
3=300
6= 600
8=800
9=900
15=1500
16= 1690
25=2500
26= 2680
45=4500
End Connections
F=Flanged
J = RTJ
S= Socket Weld
T=Threaded
W= Butt Weld
X= Threaded x Socket Weld
Trim Material
Fig.18T-FS2 _ _
Suffix Letters
Body/Bonnet Material
A20= ASTM A351, CN7M =
Cast Alloy 20
CB= ASTM A216, WCB
=
Cast Carbon Steel
CC= ASTM A216, WCC
=
Cast Carbon Steel
C5= ASTM A217, C5
=
Cast Alloy Steel (5% Chrome, .5% Moly)
C6= ASTM A217, WC6
=
Cast Alloy Steel (1.25% Chrome, .5% Moly)
C9= ASTM A217, WC9
=
Cast Alloy Steel (2.25% Chrome, 1% Moly)
C12= ASTM A217, C12
=
Cast Alloy Steel (9% Chrome, 1% Moly)
12A= ASTM A217, C12A
=
Cast Alloy Steel (9% Chrome, 1% Moly, V)
CF3= ASTM A351, CF3
=
Cast Stainless Steel
C3M= ASTM A351, CF3M =
Cast 316L Stainless Steel
CF8= ASTM A351, CF8
=
Cast 304 Stainless Steel
C7L= ASTM A351, CG3M =
Cast 317L Stainless Steel
C8M= ASTM A351, CF8M =
C8C= ASTM A351, CF8C
=
CT= ASTM A351, CG8M =
DI= ASTM A395=
Cast Ductile Iron
FS= ASTM A105=
Forged Carbon Steel
F3M= ASTM A182, F316L =
Forged 316 Stainless Steel
F5= ASTM A182, F5
=
Forged Alloy Steel (5% Chrome, .5% Moly)
F7= ASTM A182, 317
=
F7L= ASTM A182, F317L =
Forged 317L Stainless Steel
F11= ASTM A182, F11
=
Forged Alloy Steel (1.25% Chrome, .5% Moly)
F22= ASTM A182, F22
=
Forged Alloy Steel (2.25% Chrome, 1% Moly)
F9= ASTM A182, F9
=
Forged Alloy Steel (9% Chrome, 1% Moly)
F91= ASTM A182, F91
=
Forged Alloy Steel (9% Chrome, 1% Moly, V)
F8= ASTM A182, F304
=
F8M= ASTM A182, F316
=
F8C= ASTM A182, F321
=
IB= ASTM A126, CLB
=
Cast Iron
LCC= ASTM A352, LCC
=
Cast Low Temperature Carbon Steel
LF2= ASTM A350, LF2
=
Forged Low Temperature Carbon Steel
MO= ASTM A414, M35
=
Cast NI Cu (Monel***)
SPL= Special (Customer to specify)
TC9308-3
89
API Trim =
1=CR13................................ 1, 4, 8A
2=CR13/HF**.............................8
3=CR13/FHF**...........................5
4= 316........................................10
4/2= 316/HF**..............................12
4/3= 316/FHF**............................16
5= NI Cu (Monel***).................9
5/2=Monel/HF**.........................11
6= Alloy 20................................13
7=Bronze................................ N/A
A7= Aluminum Bronze............ N/A
8=Iron..................................... N/A
9= Special (Customer to Specify)
BP= By Pass
BS= Bellows Seal
CL= Chlorine Service
CR= Cryogenic Service
CW= Chain Wheel
EB= Extended Body
FP= Full Port
FS= Fire Safe
GI= Grease Injection
GO= Gear Operated
HB= Horizontal Ball Check
HP= Horizontal Piston Check
HO= Hydraulic Operator
INT= Integral Flanged
LD= Locking Device
LL= Locking Loop
LV= Live Load Packing
MO= Motor Operated
NC= NACE MR0103 Compliant
OL= Outside Weight & Lever
OX= Oxygen Service
PO= Pneumatic Operator
PS= Pressure Seal Bonnet
PT= PTFE Seats
QS=QuadroSphere
RP= Regular Port
SC= Stop Check
SL= Spring Loading
SPL= Special (Customer to specify)
TD= Tilting Disc Check
TF= Teflon* Insert
TM= Trunnion Mounted
VP= Vertical Ball Check
VL= Vertical Lift Check
VP= V-Port Disc
VT= Viton* Insert
WB= Welded Bonnet
Y= Y Pattern
*= Viton and Teflon are registered
trademarks of DuPont Company
**HF= Hardfaced - AWS 5.13 Class COCRA
***= Monel is a registered trademark of
International Nickel Company
IX. INDUSTRY STANDARDS TYPICALLY USED IN VALVE MANUFACTURING
(For Reference Only)
British Standards Institute (BS)
ISO 9001: 2000
RWTUV approved NEWCO for design, manufacture, sales, & service of industrial valves
under certificate registration number #08-1016
ISO 14001: 2004
The NEWCO/Yancheng Manufacturing Team has passed the TUV-USA ISO 14001-2004
Certification Audit. All facilities inclusive of two (2) Foundries (Lost Wax and Sand Cast), Ball
Valve Factory, Final Processing Center and Warehouses 15 & 16.
BS 1414 (1975, R’ 91) - Gate, wedge & double disk valves: steel
BS 1868 (1975, R’ 91) - Check valves: steel
BS 1873 (1975, R’ 91) - Globe & check valves: steel
BS 2080 (1989) obsolete - Flanged & buttweld end steel valves
BS 5146 - (withdrawn) Replaced by BS 6755 p.1 steel valves testing (1986) & BS 6755 p.2
(1984)
BS 5152 (1974, R’ 91) - Globe & check: cast iron
BS 5153 (1974, R’ 91) - Check: cast iron
BS 5159 (1974, R’ 91) - Ball: cast iron & carbon steel
BS 5160 (1974, R’ 91) - Globe & check: steel
BS 5163 (1986, R’ 91) - Gate, wedge & double disk: cast iron
BS 5351 (1986, R’ 91) - Ball: steel
BS 5352 (1986, R’ 91) - Globe & check: steel
BS 5418 - (withdrawn) Replaced by BS EN 19 (1992) marking: general purpose industrial
BS 5840 (1980, R’ 91) - Valve mating details for actuator operation
BS 6364 (1984, R’ 91) - Cryogenic
BS 6683 (1985, R’ 91) - Guide: installation & use of valves
BS 6755: Part 1 (1986, R’ 91) - Specification for production pressure testing requirements
BS 6755: Part 2 (1987) - Specification for fire type-testing requirements
BS EN 19 (1992) - Marking of general purpose industrial valves
American Petroleum Institute (API)
API RP 574 (1998) - Inspection practices for piping system components
API 589 (1998) - Fire test for evaluation of valve stem packing
API RP 591 (2003) - Process valve qualification procedure
API 594 (2004) - Check valves-flanged, lug, wafer & buttwelding
API 597 (1981) - Steel venturi gate valves, flanged, buttwelding ends
API 598 (2004) - Valve inspection & testing
API 599 (2002) - Metal plug valves - flanged, welding ends
API 601 (1988) - Metallic gaskets for raised-face pipe flanges & flanged connections (doublejacketed corrugated & spiral wound)
API 600 (2001) - Bolted bonnet steel gate valves for petroleum & natural as industries “ISO
adoption from ISO 10434”
API 602 (2005) - Steel gate, globe, & check valves for sizes DN100 and smaller for the
petroleum & natural gas industries
API 603 (2001) - Corrosion-resistant, bolted bonnet gate valves-flanged & buttweld ends
API 604 (1981) - Ductile iron gate valves, flanged ends
API 605 (1988) - Large-diameter carbon steel flanges (nominal pipe sizes 26” through 60”,
classes 75, 150, 300, 400, 600, & 900 (replaced by ANSI/ASME B16.47)
API 606 (1989) - Compact steel gate valves, extended body (included in API 602) fire test for
soft-seated quarter-turn valves “ISO adoption from ISO 10497-5 2004”
API 607 (2005) - Fire test for soft-seated quarter-turn valves “ISO adoption from ISO 10497-5
2004”
API 608 (2002) - Metal ball valves, flanged, threaded, & welding ends
API 609 (2004) - Butterfly valves-double flanged, lug- & wafer-type
API RP 941 (2004) - Steel for hydrogen service at elevated temperatures & pressures in
petroleum refineries & petrochemical plants
API RP 520 (2000), Part 1 - Sizing, selection & installation of pressure relieving devices in
refineries
API RP 520 (2003), Part 2 - Sizing, selection & installation of pressure relieving devices in
refineries devices in refineries
API Spec 6A (2005) - Specification for wellhead & christmas tree equipment
API Spec 6D (2005) - Specifications for pipeline valves
API Spec 14D (1994) - Specifications for wellhead surface safety valves & underwater safety
valves for offshore service
API 5B (2004) - Threading, gauging thread inspection of coring, tubing, & line pipe threads
API 6AM (2003) - Material toughness
API 6FA (1999) - Fire test for valves
API 6FC (1999) - Fire test for valves with backseats
API 6FD (1995) - Specification for fire test for check valves
API Q1 (2003) - Specification for quality programs for the petroleum, petrochemical, &
natural gas
Canadian Standards Association
B51-97 - Boiler, pressure vessel, & pressure piping code
Z245.15-96 - Steel valves
CAN3-z299.4-85 (reaffirmed 1997) - Quality assurance program - Category 4
CAN3-z299.3-85 (reaffirmed 1997) - Quality assurance program - Category 3
International Organization for Standardization
ISO 5211/1 (2001) - Industrial valves- part-turn actuator attachments
ISO 5211/2 (2001) - Part-turn valve actuator attachment-flange & coupling performance
characteristics
ISO 5211/3 (2001) - Part-turn valve actuator attachment-dimensions of driving components
ISO 5752 (1982) - Metal valves for use in flanged pipe systems face-to-face & center-to-face
dimensions
ISO 9000 (2005) - Quality management systems and fundamentals & vocabulary
ISO 10012-1 (1992) - Quality assurance requirements for measuring equipment
Manufacturers Standardization Society
ASNT-TC-1A (1996) - Recommended practice no. SNT-TC-1A 1996
SP-6 (2001) - Standard finishes for contact faces of pipe flanges & connecting-end flanges of
valves & fittings
SP-9 (r2005) - Spot facing for bronze, iron & steel flanges
SP-25 (1998) - Standard marking system for valves, fittings, flanges & unions
SP-42 (2004) - Class 150 corrosion resistant gate, globe, angle, & check valves with flanged
& buttweld ends
SP-44 (2001) - Steel pipeline flanges
SP-45 (2003) - Bypass & drain connections
SP-51 (2003) - Class 150/w corrosion resistant cast flanges & flanged fittings
SP-53 (2002) - Quality standard for steel castings & forgings for valves, flanges, & fittings &
other piping components: magnetic particle exam method
SP-54 (2002) - Quality standard for steel castings for valves, flanges, & fittings and other
piping components: radiographic examination method
SP-55 (2001) - Quality standard for steel castings for valves, flanges other piping
components-visual method for evaluation of surface irregularities
SP-60 (2004) - Connecting flange joint between tapping sleeves & tapping valves
SP-61 (2003) - Pressure testing of steel valves
SP-65 (2004) - High pressure chemical industry flanges & threaded stubs for use with lens
gaskets
SP-67 (2000A) - Butterfly valves
SP-69 (2003) - ANSI/MSS edition pipe hangers & supports, selection & application
SP-70 (1998) - Cast iron gate valves, flanged & threaded ends
SP-71 (1997) - Gray iron swing check valves, flanged & threaded ends
SP-72 (1999) - Ball valves with flanged or butt-welding ends for general service
SP-79 (2004) - Socket-welding reducer inserts
SP-81 (2001) - Stainless steel, bonnetless, flanged knife gate valves
SP-82 (1992) - Valve pressure testing methods
SP-84 (1990) - Valves - socket welding & threaded ends
SP-85 (2002) - Cast iron globe & angle valves, flanged & threaded ends
SP-86 (2002) - Guidelines for metric data in standards for valves, flanges, fittings & actuators
SP-88 (r2001) - Diaphragm valves
SP-91 (1992) - Guidelines for manual operation of valves
SP-92 (1999) - MSS valve user guide
SP-93 (r2004) - Quality standard for steel castings & forgings for valves, flanges & fittings &
other piping components- liquid penetrant exam method
SP-94 (r2004) - Quality standard for ferritic & martensitic steel castings for valves, flanges, &
fittings and others piping components - ultrasonic exam method
SP-96 (r2005) - Guidelines on terminology for valves & fittings
SP-98 (2001) - Protective coatings for the interior of valves, hydrants, & fittings
SP-99 (r2005) - Instrument valves
SP-101 (r2001) - Part-turn valve actuator attachment-flange and driving component
dimensions & performance characteristics
SP-102 (r2001) - Multi-turn valve actuator attachment: flange and driving component
dimensions & performance characteristics
SP-110 (1996) - Ball valves threaded, socket-welding, solder joint, grooved, & flared ends
SP-117 (2002) - Bellows seals for globe & gate valves
SP-118 (2002) - Compact steel globe and check valves-flanged, flangeless, threaded &
welding ends (chemical & petroleum refinery service)
SP-120 (2002) - Flexible graphite packing system for rising stem steel valves (design
requirements)
SP-121 (R2002) - Qualification testing methods for stem packing for rising stem steel valves
American Society for Testing and Materials (ASTM)
National Association of Corrosion Engineers (NACE)
American Society of Mechanical Engineers (ASME)
ASME Code (1997 addenda) - Boiler & pressure vessel code
ASME A13.1 (1996) - Scheme for the identification of piping systems
ASME B1.1 (2003) - Unified inch screw threads, UN, & UNR thread form
ASME B1.5 (1997) - ACME screw threads
ASME B1.7M (1984) - Nomenclature, definitions, & letter symbols for screw threads
ASME B1.8 (1988) - Stub ACME screw threads
ASME B1.12 (1987) - Class 5 interference - fit thread
ASME B1.20.1 (1983) - Pipe threads, general purpose, inch
ASME B1.20.3 (1976) - Dry-seal pipe threads, inch
ANSI/ASME B16.1 (1998) - Cast iron pipe flanges & flanged fittings
ANSI/ASME B16.5 (2003) - Pipe flanges & flanged fittings: NPS 1/2” through 24”
ASME B16.9 (2003) - Factory made wrought steel buttwelding fittings
ANSI/ASME B16.10 (2002) - Face-to-face & end-to-end dimensions of valves
ASME B16.11 (2001) - Forged fittings, socket welding & threaded
ASME B16.20 (1998) - Metallic gaskets for pipe flanges: ring joint spiral wound & jacketed
ASME B16.21 (2005) - Non-metallic flat gaskets for pipe flanges
ASME B16.25 (2003) - Buttwelding ends
ANSI/ASME B16.33 (2002) - Manually operated metallic gas valves for use in gas piping
systems up to 125 PSI (sizes NPS 1/2” through 2” )
ANSI/ASME B31.1 (2004) - Power piping
ANSI/ASME B31.3 (2004) - Process piping
ANSI/ASME B16.34 (2004) - Valves flanged, threaded & welding end
ANSI/ASME B16.36 (1996) - Orifice flanges
ANSI/ASME B16.38 (1985) - Large metallic valves for gas distribution (manually operated,
NPS 2-1/2” through 12”, 125 PSIG maximum)
ANSI/ASME B16.42 (1998) - Ductile iron pipe flanges & flanged fittings: classes 150 & 300
ANSI/ASME B16.47 (1996) - Large diameter steel flanges
ANSI B17.1 (1967, R’ 89) - Keys & keyseats
ANSI B18.2.2 (1987) - Square & hex nuts
ASME B31.4 (2002) - Pipeline transportation systems for liquid hydrocarbons & other
ammonia & alcohols
ANSI/ASME B31.8 (2003) - Gas transmission & distribution piping systems
ANSI/ASME B36.10 (2004) - Welded & seamless wrought steel pipe
ANSI/ASME B36.19 (2004) - Stainless steel pipe
ANSI FCI-2 (1991) - Control valve seat leakage
American Society Non-destructive Test (ASNT)
MR0175 (2005) - Sulfide stress cracking resistant metallic materials for oil field equipment
MR0103 (2005) - Materials resistant to sulfide street cracking in corrosive petroleum refining
environments
TC9308-3
90
NOTES:
TC9308-3
91
VALVES & MEASUREMENT
13127 Trinity Dr.
Stafford, Tx 77477
Toll Free 800.231.3505
Tel 281.302.4900
Fax 281.302.4801
Learn more about Cameron’s NEWCO valves at:
www.c-a-m.com/newco
newco@c-a-m.com
ENVIRONME
N
XCELLEN
LE
CE
TA
TH SAFETY
AL
A
HE
ND
CA
HSE Policy Statement
At Cameron, we are committed ethically, financially and personally to a working environment
where no one gets hurt, nothing gets harmed.
MERON
© 2013 Cameron • Produced by Technical Publications, Houston, TX, USA

NEWCO Cast Steel Valves Technical Data Sheet

Transcription

Similar documents

SPUN BOND MULTI-PLY SYNTHETIC UNDERLAYMENT

170 Déco Design™ Washable 170 Déco Design

Accura® Amethyst

vitaltech - Mag

LDI - Enviroleather: California and Montana

Free Casino Games For Mobile Phones Slot Machine Repair

sytec® - Syfan USA, Corp.

Beast Data Sheet

Swatchcard - National Office Furniture

sytec® - Syfan USA, Corp.