NEWCO Forged Steel Valves Technical Data Sheets

Transcription

NEWCO Forged Steel Valves Technical Data Sheets
NEWCO®
Forged Steel Valves
Technical Data
TC9308-4
All the information contained in this manual is the exclusive property of Cameron. Any reproduction or use of the calculations, drawings, photographs, procedures or instructions, either
expressed or implied, is forbidden without the written permission of Cameron or its authorized agent.
Initial Release 01
August 2013
Produced by Technical Publications, Houston, TX, USA
© 2013 Cameron
TC9308-4
2
PREFACE
The procedures included in this book are to be performed in conjunction with the requirements
and recommendations outlined in API Specifications. Any repairs to the equipment covered by
this book should be done by an authorized Cameron service representative. Cameron will not
be responsible for loss or expense resulting from any failure of equipment or any damage to any
property or death or injury to any person resulting in whole or in part from repairs performed
by anyone other than authorized Cameron personnel. Such unauthorized repairs shall also serve
to terminate any contractual or other warranty, if any, on the equipment and may also result in
equipment no longer meeting applicable requirements.
File copies of this manual are maintained. Revisions and/or additions will be made as deemed
necessary by Cameron. The drawings in this book are not drawn to scale, but the dimensions
shown are accurate.
This book covers Cameron products.
Cameron
P.O. Box 1212
Houston, Texas 77251-1212
713-939-2211
http://www.c-a-m.com
TC9308-4
3
NOTES:
TC9308-4
4
TABLE OF CONTENTS
Flange Dimensions - ASME B16.5.......................................................................................6
Pressure Temperature Ratings - ASME B16.34 - 2004 (Standard)....................................10
Pressure Temperature Ratings - ASME B16.34 - 2004 (Metric).........................................13
Overview..............................................................................................................................16
I.
Forged Steel Bolted and Welded Bonnet Gate Valves.............................................19
Sizes: 1/4” to 3” • Pressure Class: 150 to 4500
II.
Forged Steel Bolted and Welded Bonnet Globe Valves...........................................33
Sizes: 1/2” to 2” • Pressure Class: 150 to 4500
III.
Forged Steel Bolted and Welded Bonnet Check Valves...........................................47
Sizes: 1/2” to 2” • Pressure Class: 150 to 1500
IV. Forged Steel Cv Values Gates, Globes, Checks..........................................................56
V.
How to Order All Cameron’s NEWCO Products........................................................58
VI. Industry Standards Typically Used in Valve Manufacturing.....................................61
TC9308-4
5
FLANGE DIMENSIONS - ASME B16.5
Raised Face Class 150 and 300
B
B1
16
C
D
A
C
D
C
A
D
A
B1
16
1
16
Raised Face Class 600 to 2500
B
B
1
4
C
D
A
C
D
C
A
D
A
B
1
4
1
4
RTJ Class 600 to 2500
B
B
E
B
E
E
TC9308-4
6
F
C
D
F
A
C
F
D
C
A
D
A
Flange Dimensions in Inches
Class 150
Size
In.
mm
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
A
3.5
89
3.88
98
4.25
108
4.62
117
5
127
6
152
B
0.44
11.58
0.5
13
0.55
14.5
0.62
16
0.69
17.5
0.75
19.5
C
1.38
34.9
1.69
42.9
2
50.8
2.5
68.5
2.88
73
3.62
92.1
Ring Joint Facing
D
2.38
60.3
2.75
69
3.12
79.4
3.5
88.9
3.88
98.4
4.75
120.6
C
F
E
-
-
-
Ring
No.
-
Bolt Holes
Size
0.62
16
0.62
16
0.62
16
0.62
16
0.62
16
0.75
19
No.
4
4
4
4
4
4
Flange Dimensions in Inches
Class 300
Size
In.
mm
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
TC9308-4
A
3.75
95
4.62
117
4.88
124
5.25
133
6.12
156
6.5
165
B
0.56
14.5
0.62
16
0.69
17.5
0.75
19.5
0.81
21
0.88
22.5
C
1.38
34.9
1.69
42.9
2
50.8
2.5
68.5
2.88
73
3.62
92.1
Ring Joint Facing
D
2.62
66.7
3.25
82.5
3.5
88.9
3.88
98.4
4.5
114.3
5
127
C
F
E
-
-
-
7
Ring
No.
-
Bolt Holes
Size
0.62
16
0.75
19
0.75
19
0.75
19
0.88
22.5
0.75
19
No.
4
4
4
4
4
8
Flange Dimensions in Inches
Class 600
Size
In.
mm
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
A
3.75
95
4.62
117
4.88
124
5.25
133
6.12
156
6.5
165
B
0.56
14.5
0.62
16
0.69
17.5
0.81
21
0.88
22.5
1
25.5
C
1.38
34.9
1.69
42.9
2
50.8
2.5
63.5
2.88
73
3.62
92.1
Ring Joint Facing
D
2.62
66.7
3.25
82.5
3.5
88.9
3.88
98.4
4.5
114.3
5
127
C
F
E
2
51
2.5
63.5
2.75
70
3.12
79.5
3.56
90.5
4.25
108
1.34
34.14
1.68
42.88
2
50.8
2.38
60.32
2.69
68.28
3.25
82.55
0.22
5.6
0.25
6.3
0.25
6.3
0.25
6.3
0.25
6.3
0.31
79
Ring
No.
R 11
R 13
R 16
R 18
R 20
R 23
Bolt Holes
Size
0.62
16
0.75
19
0.75
19
0.75
19
0.88
22.5
0.75
19
No.
4
4
4
4
4
8
Flange Dimensions in Inches
Class 1500
Size
In.
mm
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
TC9308-4
A
4.75
121
5.12
130
5.88
149
6.25
159
7
178
8.5
216
B
0.88
22.5
1
22.5
1.12
29
1.12
29
1.25
32
1.5
38.5
C
1.38
34.9
1.69
42.9
2
50.8
2.5
63.5
2.88
73
3.62
92.1
Ring Joint Facing
D
3.25
82.5
3.5
88.9
4
101.6
4.38
111.1
4.88
123.8
6.5
165.1
C
F
E
2.38
60.5
2.62
66.5
2.81
71.5
3.19
81
3.62
92
4.88
124
1.56
39.67
1.75
44.45
2
50.8
2.37
60.32
2.68
68.28
3.75
95.25
0.25
6.3
0.25
6.3
0.25
6.3
0.25
6.3
0.25
6.3
0.31
7.9
8
Ring
No.
R 12
R 14
R 16
R 18
R 20
R 24
Bolt Holes
Size
0.88
22.5
0.88
22.5
1
25.5
1
25.5
1.12
28.5
1
25.5
No.
4
4
4
4
4
8
Flange Dimensions in Inches
Class 2500
Size
In.
mm
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
TC9308-4
A
5.25
133.5
5.5
139.5
6.25
159
7.25
184
8
203
9.25
235
B
1.19
30.5
1.25
32
1.38
35
1.5
38.5
1.75
44.5
2
51
C
1.38
34.9
1.69
42.9
2
50.8
2.5
63.5
2.88
73
3.62
92.1
Ring Joint Facing
D
3.5
88.9
3.75
95.3
4.25
108
5.12
130.2
5.75
146.1
6.75
171.5
C
F
E
2.56
65
2.88
73.2
3.25
82.5
4
101.6
4.5
114.3
5.25
133.4
1.68
42.88
2
50.8
2.37
60.32
2.84
72.24
3.25
82.55
4
101.6
0.25
6.3
0.25
6.3
0.25
6.3
0.31
7.9
0.31
7.9
0.31
7.9
9
Ring
No.
R 13
R 16
R 18
R 21
R 23
R 26
Bolt Holes
Size
0.88
22.5
0.88
22.5
1
25.5
1.12
28.5
1.25
32
1.12
28.5
No.
4
4
4
4
4
8
PRESSURE TEMPERATURE RATINGS ASME B16.34 - 2004 (STANDARD)
Class 150
ºF /
PSI
-20 to
100
200
300
400
500
600
650
700
750
800
850
900
950
A105*
LF2*
F11+
F22+
F5
F9
F91
285
290
290
290
290
290
290
260
260
260
260
260
260
260
230
230
230
230
230
230
230
200
200
200
200
200
200
200
170
170
170
170
170
170
170
140
140
140
140
140
140
140
125
125
125
125
125
125
125
110
110
110
110
110
110
110
95
95
95
95
95
95
95
80
80
80
80
80
80
80
65
65
65
65
65
65
65
50
50
50
50
50
50
50
35
35
35
35
35
35
35
1000 1050 1100 1150 1200
20
20
20
20
20
20
20
20**
20**
20**
20**
20
20**
20**
20**
20**
20
20**
20**
20
20**
20**
20
Class 300
ºF /
PSI
-20 to
100
200
300
400
500
600
650
700
750
800
850
900
950
A105*
LF2*
F11+
F22+
740
740
750
750
750
750
750
680
680
750
750
750
750
750
655
655
720
730
730
730
730
635
635
695
705
705
705
705
605
605
665
665
665
665
665
570
570
605
605
605
605
605
550
550
590
590
590
590
590
530
530
570
570
570
570
570
505
505
530
530
530
530
530
410
410
510
500
510
510
510
320
320
485
485
485
4185
485
230
230
450
450
375
450
450
135
135
320
385
275
375
385
F5
F9
F91
1000 1050 1100 1150 1200
85
85
215
265
200
255
365
145
175
145
170
360
95
110
100
115
300
65
70
60
75
225
40
40
35
50
145
Class 600
ºF /
PSI
-20 to
100
200
300
400
500
600
650
700
750
800
850
900
950
A105*
LF2*
F11+
F22+
1480
1480
1500
1500
1500
1500
1500
1360
1360
1500
1500
1470
1500
1500
1310
1310
1445
1455
1400
1455
1455
1265
1265
1385
1410
1335
1410
1410
1205
1205
1330
1330
1290
1330
1330
1135
1135
1210
1210
1210
1210
1210
1100
1100
1175
1175
1175
1175
1175
1060
1060
1135
1135
1135
1135
1135
1015
1015
1065
1065
1065
1065
1065
825
825
1015
1015
1015
1015
1015
640
640
975
975
975
975
975
460
460
900
900
745
900
900
275
275
640
755
550
755
775
F5
F9
F91
1000 1050 1100 1150 1200
170
170
430
535
400
505
725
290
350
290
345
720
190
220
190
225
605
130
135
125
150
445
80
80
70
105
290
Class 800
ºF /
PSI
-20 to
100
200
300
400
500
600
650
700
750
800
850
900
950
A105*
LF2*
F11+
F22+
1974
1974
2000
2000
2000
2000
2000
1810
1810
2000
2000
1964
2000
2000
1747
1747
1925
1942
1876
1942
1942
1689
1689
1849
1880
1782
1880
1880
1609
1609
1774
1774
1724
1774
1774
1515
1515
1614
1614
1614
1614
1614
1467
1467
1569
1569
1569
1569
1569
1414
1414
1515
1515
1515
1515
1515
1352
1352
1419
1419
1419
1419
1419
1098
1098
1355
1355
1355
1355
1355
850
850
1298
1298
1298
1298
1298
613
613
1200
1200
995
1200
1200
365
365
850
1025
733
1005
1032
F5
F9
F91
TC9308-4
10
1000 1050 1100 1150 1200
227
227
577
712
530
675
968
383
467
383
458
960
257
293
257
302
805
173
182
165
200
595
110
110
93
138
383
Class 900
ºF /
PSI
-20 to
100
200
300
400
500
600
650
700
750
800
850
900
950
1000 1050 1100 1150 1200
A105*
LF2*
F11+
F22+
F5
F9
F91
2220
2220
2250
2250
2250
2250
2250
2035
2035
2250
2250
2210
2250
2250
1965
1965
2165
2185
2100
2185
2185
1900
1900
2080
2115
2005
2115
2115
1810
1810
1995
1995
1940
1995
1995
1705
1705
1815
1815
1815
1815
1815
1650
1650
1765
1765
1765
1765
1765
1590
1590
1705
1705
1705
1705
1705
1520
1520
1595
1595
1595
1595
1595
1235
1235
1525
1525
1525
1525
1525
955
955
1460
1460
1460
1460
1460
690
690
1350
1350
1120
1350
1350
410
410
955
1160
825
1130
1160
255
255
650
800
595
760
1090
430
525
430
515
1080
290
330
290
340
905
195
205
185
225
670
125
125
105
155
430
Class 1500
ºF /
PSI
-20 to
100
200
300
400
500
600
650
700
750
800
850
900
950
1000 1050 1100 1150 1200
A105*
LF2*
F11+
F22+
3705
3705
3750
3750
3750
3750
3750
3395
3395
3750
3750
3680
3750
3750
3270
3270
3610
3640
3495
3640
3640
3170
3170
3465
3530
3345
3530
3530
3015
3015
3325
3325
3230
3325
3325
2840
2840
3025
3025
3025
3025
3025
2745
2745
2940
2940
2940
2940
2940
2665
2665
2840
2840
2840
2840
2840
2535
2535
2660
2660
2660
2660
2660
2055
2055
2540
2540
2540
2540
2540
1595
1595
2435
2435
2435
2435
2435
1150
1150
2245
2245
1870
2245
2245
685
685
1595
1930
1370
1885
1930
430
430
1080
1335
995
1270
1820
F5
F9
F91
720
875
720
855
1800
480
550
480
565
1510
325
345
310
375
1115
205
205
170
255
720
Class 1690
ºF /
PSI
-20 to
100
200
300
400
500
600
650
700
750
800
850
900
950
1000 1050 1100 1150 1200
A105*
LF2*
F11+
F22+
F5
F9
F91
4173
4173
4225
4225
4225
4225
4225
3824
3824
4225
4225
4146
4225
4225
3684
3684
4067
4102
3939
4102
4102
3571
3571
3904
3977
3768
3977
3977
3397
3397
3746
3746
3639
3746
3746
3199
3199
3408
3408
3408
3408
3408
3093
3093
3313
3313
3313
3313
3313
2999
2999
3199
3199
3199
3199
3199
2857
2857
2996
2996
2996
2996
2996
2316
2316
2861
2861
2861
2861
2861
1796
1796
2744
2744
2744
2744
2744
1295
1295
2530
2530
2107
2530
2530
772
772
1796
2175
1544
2124
2175
484
484
1217
1505
1120
1431
2050
811
985
811
964
2028
541
619
541
637
1701
367
388
349
423
1256
232
232
192
288
811
Class 2500
ºF /
PSI
-20 to
100
200
300
400
500
600
650
700
750
800
850
900
950
1000 1050 1100 1150 1200
A105*
LF2*
F11+
F22+
6170
6170
6250
6250
6250
6250
6250
5655
5655
6250
6250
6135
6250
6250
5450
5450
6015
6070
5830
6070
6070
5280
5280
5775
5880
5570
5880
5880
5025
5025
5540
5540
5385
5540
5540
4730
4730
5040
5040
5040
5040
5040
4575
4575
5905
4905
4905
4905
4905
4425
4425
4730
4730
4730
4730
4730
4230
4230
4430
4430
4430
4430
4430
3430
3430
4230
4230
4230
4230
4230
2655
2655
4060
4060
4060
4060
4060
1915
1915
3745
3745
3115
3745
3745
1145
1145
2655
3220
2285
3145
3220
715
715
1800
2230
1655
2115
3030
F5
F9
F91
TC9308-4
11
1200
1455
1200
1430
3000
800
915
800
945
2515
545
570
515
630
1855
345
345
285
430
1200
Class 2680
ºF /
PSI
-20 to
100
200
300
400
500
600
650
700
750
800
850
900
950
1000 1050 1100 1150 1200
A105*
LF2*
F11+
F22+
F5
F9
F91
6615
6615
6700
6700
6700
6700
6700
6063
6063
6700
6700
6576
6700
6700
5843
5843
6448
6507
6249
6507
6507
5660
5660
6191
6303
5971
6303
6303
5386
5386
5938
5938
5772
5938
5938
5071
5071
5403
5403
5403
5403
5403
4905
4905
5258
5258
5258
5258
5258
4743
4743
5071
5071
5071
5071
5071
4534
4534
4749
4749
4749
4749
4749
3677
3677
4534
4534
4534
4534
4534
2847
2847
4352
4352
4352
4352
4352
2054
2054
4015
4015
3339
4015
4015
1227
1227
2847
3452
2450
3371
3452
766
766
1930
2390
1775
2267
3248
1286
1560
1286
1533
3216
858
981
858
1013
2696
584
611
552
675
1989
369
369
306
461
1286
Class 4500
ºF /
PSI
-20 to
100
200
300
400
500
600
650
700
750
800
850
900
950
1000 1050 1100 1150 1200
A105*
LF2*
F11+
F22+
11110
11110
11250
11250
11250
11250
11250
10185
10185
11250
11250
11040
11250
11250
9815
9815
10830
10925
10490
10925
10925
9505
9505
10400
10585
10030
10585
10586
9040
9040
9965
9965
9690
9965
9965
8515
8515
9070
9070
9070
9070
9070
8240
8240
8825
8825
8825
8825
8825
7960
7960
8515
8515
8515
8515
8515
7610
7610
7970
7970
7970
7970
7970
6170
6170
7610
7610
7610
7610
7610
4785
4785
7305
7305
7305
7305
7305
3455
3455
6740
6740
5605
6740
6740
2055
2055
4785
5795
4115
5655
5795
1285
1285
3240
4010
2985
3805
5450
F5
F9
F91
2160
2625
2160
2570
5400
1440
1645
1440
1695
4525
975
1030
925
1130
3345
615
615
515
770
2160
* Not recommended for prolonged use above 800° F.
+ Not recommended for prolonged use above 1100° F.
** For weld end valves only. Flanged end ratings terminate at 1000° F.
Note: Packing, gasket or bolting may limit temperature. Please advise service temperature if
above 1000° F. Ratings from ASME B16.34 standard class valves. Special class weld end
valves to ASME B16.34 are available on special order.
TC9308-4
12
PRESSURE TEMPERATURE RATINGS ASME B16.34 - 2004 (METRIC)
Class 150
ºC /
BAR
A105*
LF2*
F11+
F22+
F5
F9
F91
-29 to
38
19.6
19.6
19.8
19.8
20.0
20.0
20.0
100
150
200
250
300
350
375
400
425
450
475
500
538
575
600
625
650
17.7
17.7
17.7
17.7
17.7
17.7
17.7
15.8
15.8
15.8
15.8
15.8
15.8
15.8
13.8
13.8
13.8
13.8
13.8
13.8
13.8
12.1
12.1
12.1
12.1
12.1
12.1
12.1
10.2
10.2
10.2
10.2
10.2
10.2
10.2
8.4
8.4
8.4
8.4
8.4
8.4
8.4
7.4
7.4
7.4
7.4
7.4
7.4
7.4
6.5
6.5
6.5
6.5
6.5
6.5
6.5
5.5
5.5
5.5
5.5
5.5
5.5
5.5
4.6
4.6
4.6
4.6
4.6
4.6
4.6
3.7
3.7
3.7
3.7
3.7
3.7
3.7
2.8
2.8
2.8
2.8
2.8
2.8
2.8
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.4**
1.4**
1.4**
1.4**
1.4**
1.4**
1.4**
1.4**
1.4**
1.4**
1.4**
1.4**
1.4**
1.4**
1.4**
1.1**
1.1**
0.9**
1.4**
1.4**
Class 300
ºC /
BAR
A105*
LF2*
F11+
F22+
F5
F9
F91
-29 to
38
51.1
51.1
51.7
51.7
51.7
51.7
51.7
100
150
200
250
300
350
375
400
425
450
475
500
538
575
600
625
650
46.6
46.6
51.5
51.5
51.5
51.5
51.5
45.1
45.1
49.7
50.3
50.3
50.3
50.3
43.8
43.8
48.0
48.6
48.6
48.6
48.6
41.9
41.9
46.3
46.3
46.3
46.3
46.3
39.8
39.8
42.9
42.9
42.9
42.9
42.9
37.6
37.6
40.3
40.3
40.3
40.3
40.3
36.4
36.4
38.9
38.9
38.9
38.9
38.9
34.7
34.7
36.5
36.5
36.5
36.5
36.5
28.8
28.8
35.2
35.2
35.2
35.2
35.2
23.0
23.0
33.7
33.7
33.7
33.7
33.7
17.4
17.4
31.7
31.7
27.9
31.7
31.7
11.8
11.8
25.7
28.2
21.4
28.2
28.2
5.9
5.9
14.9
18.4
13.7
17.5
25.2
8.8
10.5
8.9
10.5
24.0
6.1
6.9
6.2
7.2
19.5
4.3
4.5
4.0
5.0
14.6
2.8
2.8
2.4
3.5
9.9
Class 600
ºC /
BAR
A105*
LF2*
F11+
F22+
F5
F9
F91
-29 to
38
102.1
102.1
103.4
103.4
103.4
103.4
103.4
100
150
200
250
300
350
375
400
425
450
475
500
538
575
600
625
650
93.2
93.2
103.0
103.0
103.0
103.0
103.0
90.2
90.2
99.5
100.3
100.3
100.3
100.3
87.6
87.6
95.9
97.2
97.2
97.2
97.2
83.9
83.9
92.7
92.7
92.7
92.7
92.7
79.6
79.6
85.7
85.7
85.7
85.7
85.7
75.1
75.1
80.4
80.4
80.4
80.4
80.4
72.7
72.7
77.6
77.6
77.6
77.6
77.6
69.4
69.4
73.3
73.3
73.3
73.3
73.3
57.5
57.5
70.0
70.0
70.0
70.0
70.0
46.0
46.0
67.7
67.7
67.7
67.7
67.7
34.9
34.9
63.4
63.4
55.7
63.4
63.4
23.5
23.5
51.5
56.5
42.8
56.5
56.5
11.8
11.8
29.8
36.9
27.4
35.0
50.0
17.6
21.1
17.8
20.9
47.9
12.2
13.8
12.5
14.4
39.0
8.5
8.9
8.0
9.9
29.2
5.7
5.7
4.7
7.1
19.9
Class 800
ºC /
BAR
A105*
LF2*
F11+
F22+
F5
F9
F91
-29 to
38
136.0
136.0
137.8
137.8
137.8
137.8
137.8
TC9308-4
100
150
200
250
300
350
375
400
425
450
475
500
538
575
600
625
650
124.7
124.7
137.8
137.8
135.3
137.8
137.8
120.4
120.4
132.6
133.8
128.6
133.8
133.8
116.3
116.3
127.4
129.5
122.8
129.5
129.5
110.8
110.8
122.2
122.2
118.8
122.2
122.2
104.4
104.4
111.2
111.2
111.2
111.2
111.2
101.1
101.1
108.1
108.1
108.1
108.1
108.1
97.4
97.4
104.4
104.4
104.4
104.4
104.4
93.1
93.1
97.7
97.7
97.7
97.7
97.7
75.7
75.7
93.4
93.4
93.4
93.4
93.4
58.6
58.6
89.5
89.5
89.5
89.5
89.5
42.3
42.3
82.7
82.7
68.6
82.7
82.7
25.2
25.2
58.6
70.6
50.5
69.3
71.1
15.6
15.6
39.7
49.0
36.5
46.5
66.7
26.4
32.2
26.4
31.6
66.2
17.7
20.2
17.7
20.8
55.5
11.9
12.5
11.4
13.8
41.0
7.6
7.6
6.4
9.5
26.4
13
Class 900
ºC /
BAR
A105*
LF2*
F11+
F22+
F5
F9
F91
-29 to
38
153.2
153.2
155.1
155.1
155.1
155.1
155.1
100
150
200
250
300
350
375
400
425
450
475
500
538
575
600
625
650
139.8
139.8
154.4
154.6
154.6
154.6
154.6
135.2
135.2
149.2
150.6
150.6
150.6
150.6
131.4
131.4
143.9
145.8
145.8
145.8
145.8
125.8
125.8
139.0
139.0
139.0
139.0
139.0
119.5
119.5
128.6
128.6
128.6
128.6
128.6
112.7
112.7
120.7
120.7
120.7
120.7
120.7
109.1
109.1
116.5
116.5
116.5
116.5
116.5
104.2
104.2
109.8
109.8
109.8
109.8
109.8
86.3
86.3
105.1
105.1
105.1
105.1
105.1
69.0
69.0
101.4
101.4
101.4
101.4
101.4
52.3
52.3
95.1
95.1
83.6
95.1
95.1
35.3
35.3
77.2
84.7
64.1
84.7
84.7
17.7
17.7
44.7
55.3
41.1
52.5
75.2
26.4
31.6
26.7
31.4
71.8
18.3
20.7
18.7
21.5
58.5
12.8
13.4
12.0
14.9
43.8
8.5
8.5
7.1
10.6
29.8
Class 1500
ºC /
BAR
A105*
LF2*
F11+
F22+
F5
F9
F91
-29 to
38
255.3
255.3
258.6
258.6
258.6
258.6
258.6
100
150
200
250
300
350
375
400
425
450
475
500
538
575
600
625
650
233.0
233.0
257.4
257.6
257.6
257.6
257.6
225.4
225.4
248.7
250.8
250.8
250.8
250.8
219.0
219.0
239.8
243.4
243.4
243.4
243.4
209.7
209.7
231.8
231.8
231.8
231.8
231.8
199.1
199.1
214.4
214.4
214.4
214.4
214.4
187.8
187.8
201.1
201.1
201.1
201.1
201.1
181.8
181.8
194.1
194.1
194.1
194.1
194.1
173.6
173.6
183.1
183.1
183.1
183.1
183.1
143.8
143.8
175.1
175.1
175.1
175.1
175.1
115.0
115.0
169.0
169.0
169.0
169.0
169.0
87.2
87.2
158.2
158.2
139.3
158.2
158.2
58.8
58.8
128.6
140.9
106.9
140.9
140.9
29.5
29.5
74.5
92.2
68.6
87.5
125.5
44.0
52.6
44.4
52.3
119.7
30.5
34.4
31.2
35.9
97.5
21.3
22.3
20.0
24.8
73.0
14.2
14.2
11.8
17.7
49.6
Class 1690
ºC /
BAR
A105*
LF2*
F11+
F22+
F5
F9
F91
-29 to
38
287.5
287.5
291.1
291.1
291.1
291.1
291.1
100
150
200
250
300
350
375
400
425
450
475
500
538
575
600
625
650
263.5
263.5
291.1
291.1
285.7
291.1
291.1
253.8
253.8
280.2
282.6
271.4
282.6
282.6
246.0
246.0
269.0
274.0
259.6
274.0
274.0
234.0
234.0
258.1
258.1
250.8
258.1
258.1
220.4
220.4
234.8
234.8
234.8
234.8
234.8
213.1
213.1
28.3
228.3
228.3
228.3
228.3
206.7
206.7
220.4
220.4
220.4
220.4
220.4
196.9
196.9
206.4
206.4
206.4
206.4
206.4
159.6
159.6
197.1
197.1
197.1
197.1
197.1
123.8
123.8
189.0
189.0
189.0
189.0
189.0
89.2
89.2
174.3
174.3
145.1
174.3
174.3
53.2
53.2
123.8
149.9
106.4
146.4
149.9
33.4
33.4
83.8
103.7
77.2
98.6
141.2
55.9
67.9
55.9
66.4
139.7
37.3
42.7
37.3
43.9
117.2
25.3
26.7
24.0
29.2
86.5
16.0
16.0
13.2
19.9
55.9
Class 2500
ºC /
BAR
A105*
LF2*
F11+
F22+
F5
F9
F91
-29 to
38
425.5
425.5
430.9
430.9
430.9
430.9
430.9
TC9308-4
100
150
200
250
300
350
375
400
425
450
475
500
538
575
600
625
650
388.3
388.3
429.0
429.4
429.4
429.4
429.4
375.6
375.6
414.5
418.2
418.2
418.2
418.2
365.0
365.0
399.6
405.4
405.4
405.4
405.4
349.5
349.5
386.2
386.2
386.2
386.2
386.2
331.8
331.8
357.1
357.1
357.1
357.1
357.1
313.0
313.0
335.3
335.3
335.3
335.3
335.3
303.1
303.1
323.2
323.2
323.2
323.2
323.2
289.3
289.3
304.9
304.9
304.9
304.9
304.9
239.7
239.7
291.6
291.6
291.6
291.6
291.6
191.7
191.7
281.8
281.8
281.8
281.8
281.8
145.3
145.3
263.9
263.9
232.1
263.9
263.9
97.9
97.9
214.4
235.0
178.2
235.0
235.0
49.2
49.2
124.1
153.7
114.3
145.8
208.9
73.4
87.7
74.0
87.1
199.5
50.9
57.4
51.9
59.8
162.5
35.5
37.2
33.3
41.4
121.7
23.6
23.6
19.7
29.5
82.7
14
Class 2680
ºC /
BAR
A105*
LF2*
F11+
F22+
F5
F9
F91
-29 to
38
455.7
455.7
461.6
461.6
461.6
461.6
461.6
100
150
200
250
300
350
375
400
425
450
475
500
538
575
600
625
650
417.7
417.7
461.6
461.6
453.1
461.6
461.6
402.6
402.6
444.3
448.3
430.6
448.3
448.3
390.0
390.0
426.6
434.3
411.4
434.3
434.3
371.1
371.1
409.1
409.1
397.7
409.1
409.1
349.4
349.4
372.2
372.2
372.2
372.2
372.2
337.9
337.9
362.3
362.3
362.3
362.3
362.3
326.8
326.8
349.4
349.4
349.4
349.4
349.4
312.4
312.4
327.2
327.2
327.2
327.2
327.2
253.3
253.3
312.4
312.4
312.4
312.4
312.4
196.1
196.1
299.9
299.9
299.9
299.9
299.9
141.5
141.5
276.6
276.6
230.1
276.6
276.6
84.5
84.5
196.1
237.8
168.8
232.3
237.8
52.8
52.8
132.9
164.7
122.3
156.2
223.8
88.6
107.5
88.6
105.6
221.6
59.1
67.6
59.1
69.8
185.7
40.2
42.1
38.0
46.5
137.0
25.4
25.4
21.1
31.7
88.6
Class 4500
ºC /
BAR
A105*
LF2*
F11+
F22+
F5
F9
F91
-29 to
38
765.9
765.9
775.7
775.7
775.7
775.7
775.7
100
150
200
250
300
350
375
400
425
450
475
500
538
575
600
625
650
699.0
699.0
772.2
773.0
773.0
773.0
773.0
676.1
676.1
746.2
752.8
752.8
752.8
752.8
657.0
657.0
719.4
729.8
729.8
729.8
729.8
629.1
629.1
694.8
694.8
694.8
694.8
694.8
597.3
597.3
642.6
642.6
642.6
642.6
642.6
563.5
563.5
603.3
603.3
603.3
603.3
603.3
545.5
545.5
581.8
581.8
581.8
581.8
581.8
520.8
520.8
548.5
548.5
548.5
548.5
548.5
431.5
431.5
524.7
524.7
524.7
524.7
524.7
345.1
345.1
507.0
507.0
507.0
507.0
507.0
261.5
261.5
474.8
474.8
417.8
474.8
474.8
176.3
176.3
385.9
423.0
320.7
423.0
423.0
88.6
88.6
223.4
276.6
205.7
262.4
375.8
132.0
157.9
133.3
156.8
359.1
91.6
103.3
93.5
107.7
292.5
63.9
66.9
59.9
74.5
219.1
42.6
42.6
35.5
53.2
148.9
* Not recommended for prolonged use above 425° C.
+ Not recommended for prolonged use above 600° C.
** For weld end valves only. Flanged end ratings terminate at 538° C.
Note: Packing, gasket or bolting may limit temperature. Please advise service temperature if
above 538° C. Ratings from ASME B16.34 standard class valves. Special class weld end
valves to ASME B16.34 are available on special order.
TC9308-4
15
OVERVIEW
Valve and I.D. Tag Overview
The identification tag displays all construction and tracking data regarding the respective
valve on which it is attached. Below is a general overview of the identification tag components.
I.D. tags are located under the handwheel nut.
Globe and check valves will have a flow direction arrow on body for proper installation.
I.D. Tag
Material
Flow
Direction
Pattern
Size
Pressure Class
Cameron’s NEWCO 41 I.D. Tag
Figure Number
CE Mark
Pattern Number
Valve Type
Body Material
Nominal Valve Size
Stem Material
Disc Material
Pressure Class
Manufactured Date
Factory Reference Number
Seat Material
Maximum Temperature
Minimum Temperature
Max. Press. @ Max. Temp.
Design Specifications
Pattern
Max. Press. @ Min. Temp.
TC9308-4
16
Cameron’s NEWCO 45 I.D. Tag
Figure Number
Pattern
Valve Type
CE Mark
Body Material
Pressure Class
Stem Material
Disc Material
Nominal Valve Size
Manufactured Date
Seat Material
Factory Reference Number
Minimum Temperature
Maximum Temperature
Max. Press. @ Min. Temp.
Max. Press. @ Max. Temp.
Design Specifications
Body/Bonnet Materials
Cameron’s NEWCO® forged steel valves are available in stock in a wide range of body/
bonnet materials and optional trim materials. Listed below are some of the more popular
materials. Additional materials are available. Please contact Cameron or your local distributor for details.
NEWCO
Material
Designation
Common
Description
ASTM
Specs.
FS
Carbon Steel
A105
Non-corrosive service water, oil and gases at temperatures
between -20º F and +800º F.
LF2
Low Temp. Carbon
A350
Low temperature service between -50º F and +800º F.
F11
1.25% Chrome and
.5% Moly
A182
Non-corrosive service water, oil and gases at temperatures
between -20º F and +1100º F.
F22
2.25% Chrome and
1% Moly
A182
Non-corrosive service water, oil and gases at temperatures
between -20º F and +1100º F.
F5
5% Chrome and
.5% Moly
A182
Corrosive, non-corrosive or erosive service at temperatures
between -20º F and +1200º F.
F9
9% Chrome and
1% Moly
A182
Corrosive, non-corrosive or erosive service at temperatures
between -20º F and +1200º F.
F91
9% Chrome, 1%
Moly and V
A182
Corrosive, non-corrosive or erosive service at temperatures
between -20º F and +1200º F.
F316
316
A182
Corrosive, cryogenic or high temperature service between
-450º F and +1200º F.
Body/Bonnet
Material Service Limitations*
* Limitations are per 2004 Edition of ASME B16.34.
TC9308-4
17
Trim Materials
The following are Cameron’s NEWCO standard trim designations:
Wedge or
Disc
Facing (1)
Stem
Other
Trim
Parts (2)
CR 13
CR 13
CR 13
CR 13
Non-corrosive applications.
Steam, gas and general
service to 700º F. Oil and oil
vapor to 900º F.
8
HF
CR 13
CR 13
CR 13
Steam, gas and general
service to 1000º F. Standard
trim for gate valves.
Full Stellite
5
HF
HF
CR 13
CR 13
Premium trim service to
1200º F. Excellent for high
pressure water and steam
service.
4
316
10
316
316
316
316
Corrosive services to 850º
F. Low temperature service
standard for 316 SS valves.
4/2
316/Half
Stellite
12
HF
316
316
316
4/3
316/Full
Stellite
16
HF
HF
316
316
5
Monel
9
NiCu
NiCu
NiCu
NiCu
5/2
Monel/Half
Stellite
11
HF
NiCu
NiCu
NiCu
5/3
Monel/Full
Stellite
-
HF
HF
NiCu
NiCu
6
Alloy 20
13
A20
A20
A20
A20
X
Special
Special
Special
Special
Special
Special
Trim
Number
Common
Name
API 600 Seat Ring
Trim No. Facing (1)
1
13 Chrome
1
2
Half Stellite
3
Service Limitations
Corrosive services to 750º F.
Corrosive services to 300º F.
Customer to specify.
(1) Facing is defined as the seating surface of a seat ring and wedge/disc.
(2) Other trim parts are defined as small internal parts that are normally in contact with the service fluid. This includes the stem, etc. in gate and globe valves and the swing check disc nut.
Features and Benefits
TC9308-4
• Material Test Reports
• Ship from Multiple North American Locations
• International Organization for Standardization (ISO)
• Extensive Engineering Capabilities
• Traceability
• Excellent Customer Service
• Fugitive Emissions Tested
• Warranty
• API-598 Tested
• Field Services for Start-up
• Major End-user Approved
• In-house Automation Capabilities
18
I. FORGED STEEL BOLTED AND WELDED BONNET GATE VALVES
SIZES: 1/4” TO 3” (6MM TO 80MM) • PRESSURE CLASS: 150 TO 4500
Cameron’s Typical NEWCO Forged Steel Bolted and Welded Bonnet Gate Valve Expanded
View
1
2
11
12
3
13
14
4
5
6
11
7
15
8
16
9
10
TC9308-4
19
1. Handwheel Nut: The handwheel nut secures the handwheel to the bonnet assembly.
2. Handwheel: The handwheel cycles the valve.
3. Stem Nut: The stem nut provides a precision guide for proper stem alignment.
4. & 11. Gland Bolts and Nuts: The gland bolts and nuts allow for easy adjustments for packing compression.
5. Stuffing Box: The stuffing box contains the packing.
6. Bonnet Bolts: The bonnet bolts secure the bonnet to the body.
7. Yoke and Bonnet: The bonnet assemblies are built to the same standards as the bodies.
Larger size gate valves utilize a multi-piece bonnet design.
8. Bonnet Gasket: The bonnet gasket creates a leakproof seal between the bonnet and
body.
9. Body: Cameron’s NEWCO forged steel bodies provide low resistance flow and optimum
strength and performance.
10. Seat Rings: To ensure a stable shutoff, seat rings are aligned and swaged into the valve,
then precision ground for optimal seating.
12. Gland Flange: The gland flange applies pressure to the gland for accurate packing adjustments.
13. Gland: The gland compresses the packing to create a stem seal above the back seat between the bonnet and stem.
14. Packing: The packing creates a seal above the back seat between the bonnet and stem.
15. Stem: The stem is precision machined and inserts into the horizontal channel in the disc.
16. Wedge: The solid wedge is machined to the tightest tolerances to ensure trouble free
shutoff and cycling.
TC9308-4
20
FORGED STEEL BOLTED AND WELDED BONNET GATES
THREADED, SOCKET WELD AND BUTTWELD ENDS CONVENTIONAL PORT
CLASS 800 TO 2500
SIZES: 1/4” TO 3” (6MM TO 80MM)
Design and Manufacturing Standards
Valve Design: API 602
Pipe Threads, General Purpose, Inch: ASME B1.20.1
Socket Welding and Threaded: ASME B16.11
Tested in Accordance With: API 598
Recommended Spare Parts*
BOLTED BONNET
C
WELDED BONNET
D
B
A
TC9308-4
21
Class 800 to 2500
Bolted and Welded Bonnet Gates
Size
In.
----mm
1/4
6
3/8
9
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
3
75
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
A
41
Class 800 WB
C
B
45
3.1
80
3.1
80
41
45
41
45
D
41
Wt.
45
-
0.31
5.7
3.1
8
145
80
0.39
5.7
3.1
10
145
80
0.39 0.39 5.7 4.9 3.2 3.3
10
10 145 124.5 80 83.8
0.55 0.55 6.1 5.2 3.2 3.3
14
14 155 132.1 80 83.8
0.71 0.71 7.3 6.7 3.9 4.7
18
18 185 170.2 100 119.4
0.95 0.95 8.6 7.6 4.7 5.9
24
24 218 193 120 149.9
1.22 1.22 10.0 8.3 5.5 5.9
30
30 255 210.8 140 149.9
1.44 1.44 10.9 9.3 5.5 6.7
36.5 36.5 277 236.2 140 170.2
-
A
Class 1500 WB
C
3.2
80
3.5
90
4.3
110
5.0
127
5.0
127
5.1
130
3.1
78.7
3.6
91.4
4.4
111.8
4.7
119.4
4.7
119.4
5.5
139.7
B
D
41
45
A
41
3.5
1.6
3.5
1.6
B
45
3.1
80
3.1
80
3.2 3.1
1.6 1.4
4.4 3.7
2
1.7
7.1 6.6
3.2
3
10.7 11
4.8
5
14.3 12.3
6.5 5.6
18.7 20.3
8.5 9.2
-
3.2
80
3.5
90
4.3
110
5.0
127
5.0
127
5.1
130
3.1
78.7
3.6
91.4
4.4
111.8
4.7
119.4
4.7
119.4
5.5
139.7
7.3
184.2
Wt.
Class 800 BB
C
41
45
41
45
D
41
Wt.
45
41
45
0.31
5.7
3.1
8
145
80
0.39
5.7
3.1
10
145
80
0.39 0.39 5.7 4.9 3.2 3.3
10
10 145 124.5 80 83.8
0.55 0.55 6.1 5.2 3.2 3.3
14
14 155 132.1 80 83.8
0.71 0.71 7.3 6.7 3.9 4.7
18
18 185 170.2 100 119.4
0.95 0.95 8.6 7.6 4.7 5.9
24
24 218 193 120 149.9
1.22 1.22 10.0 8.3 5.5 5.9
30
30 255 210.8 140 149.9
1.44 1.44 10.9 9.3 5.5 6.7
36.5 36.5 277 236.2 140 170.2
2.13
15.5
11.3
53.98
393.7
285.8
3.9 3.1
1.8 1.4
4.6 3.7
2.1 1.7
7.9 6.6
3.6
3
11.2 11
5.3
5
15.4 12.3
7.5 5.6
20.0 20.3
9.8 9.2
56
25.5
Class 1500 BB
C
Wt.
A
B
D
3.9
1.8
3.9
1.8
41
45
41
45
41
45
41
45
41
45
41
45
41
45
41
45
41
45
41
45
3.5
90
4.3
110
4.7
120
5.1
130
5.1
130
5.9
150
4.4
111.8
4.4
111.8
4.5
114.3
4.7
119.4
5.5
139.7
6.4
162.6
0.39
10
0.55
14
0.75
18
0.95
24
1.16
29
1.44
36.5
0.55
13.97
0.55
13.97
0.71
18.03
0.95
24.13
1.14
28.95
1.44
36.57
6.07
152
7.1
180
8.6
218
9.8
250
10.8
275
12.6
320
7.8
198.1
7.8
198.1
8.6
218.4
9.3
236.2
10.8
274.3
12.6
320.0
3.2
80
3.9
100
4.7
120
5.5
140
5.5
140
6.7
170
4.9
124.5
4.9
124.5
6.2
157.5
6.2
157.5
7
177.8
7.9
200.7
5.0
2.2
8.4
3.6
12.6
5.2
14.6
7.5
22.0
10
33.0
14.5
9
4.1
9.5
4.3
13.5
6.1
19.2
8.7
26.9
12.2
39
17.7
3.5
90
4.3
110
4.7
120
5.1
130
5.1
130
5.9
150
4.4
111.8
4.4
111.8
4.5
114.3
4.7
119.4
5.5
139.7
6.4
162.6
0.39
10
0.55
14
0.75
18
0.95
24
1.16
29
1.44
37
0.55
139.7
0.55
139.7
0.71
18.03
0.95
24.13
1.14
28.95
1.44
36.57
6.07
152
7.1
180
8.6
218
9.9
252
10.8
275
12.6
320
7.8
198.1
7.8
198.1
8.6
218.4
9.3
236.2
10.8
274.3
12.6
320.0
3.2
80
3.9
100
4.7
120
5.5
140
5.5
170
6.7
170
4.9
124.5
4.9
124.5
6.2
157.5
6.2
157.5
7
177.8
7.9
200.7
5.5
2.5
8.4
3.8
11.9
5.4
17.6
8
22.4
10
33.0
15
9
4.1
9.5
4.3
13.5
6.1
19.2
8.7
26.9
12.2
39
17.7
TC9308-4
22
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
A
Class 2500 WB
C
B
D
Wt.
A
B
Class 2500 BB
C
D
Wt.
41
45
41
45
41
45
41
45
41
45
41
45
41
45
41
45
41
45
41
45
4.3
110
4.7
120
5.1
130
5.1
130
8.3
210
9.4
240
5.9
149.9
5.9
149.9
6.7
170.2
8.7
220.9
8.7
220.9
9.8
248.9
0.39
10
0.55
14
0.75
18
0.95
24
1.16
29
1.44
36.5
0.39
9.9
0.55
13.97
0.71
18.03
0.95
24.13
1.14
28.95
1.44
36.57
6.9
175
8.3
210
9.4
240
11.0
280
12.2
310
14
355
9.5
241.3
9.5
241.3
10.8
274.3
13.1
332.7
13.1
332.7
16.8
426.7
3.9
100
4.7
120
5.5
140
6.7
170
6.7
170
10.2
260
6.3
160
6.3
160
7.1
180.3
7.8
198.1
7.8
198.1
11.8
299.7
7.7
3.5
12.1
5.5
16.5
7.5
22
10
35.2
16
55
25
27.1
12.3
26.6
12.1
26
11.8
46
20.9
60.5
27.5
117.3
53.3
4.3
110
4.7
120
5.1
130
8.3
210
8.3
210
9.4
240
5.9
149.9
5.9
149.9
6.7
170.2
8.7
220.9
8.7
220.9
9.8
248.9
0.39
9.9
0.55
13.97
0.75
19.05
0.95
24.13
1.16
29.46
1.44
36.57
0.39
9.9
0.55
13.97
0.71
18.03
0.95
24.13
1.14
28.95
1.44
36.57
8.3
210
10.0
255
10.4
265
14.4
365
14.8
375
15.4
390
9.5
241.3
9.5
241.3
10.8
274.3
13.1
332.7
13.1
332.7
16.8
426.7
3.9
100
4.7
120
5.5
140
6.7
170
6.7
170
10.2
260
6.3
160
6.3
160
7.1
180.3
7.8
198.1
7.8
198.1
11.8
299.7
12.1
5.5
18.7
8.5
22.4
10.2
57.2
26
57.2
26
81.4
37
27.1
12.3
26.6
12.1
26
11.8
46
20.9
60.5
27.5
117.3
53.3
Typical Bill Materials (See page 61 for available materials)
Component
Material
ASTM Spec
Body
Carbon Steel
A105N
Bonnet
Carbon Steel
A105N
* Packing
Graphite W/Braided Carbon Fiber End Rings
* Gasket
Stainless Steel 316 Graphite
Stem
Stainless Steel
A479-410
Wedge
Stainless Steel
13 Chrome
Seat Rings
Stainless Steel
A479-410
Bonnet Bolt
Alloy Steel
A193 B7
Handwheel Nut
Carbon Steel
Commercial
Nameplate
Aluminum
Commercial
Handwheel
Carbon Steel
A105N
Yoke Sleeve
Stainless Steel
AISI 416
Gland Nuts
Carbon Steel
A194 2H
Gland Flange
Carbon Steel
A105N
Gland Studs
Stainless Steel
AISI 410
Packing Gland
Stainless Steel
A479-316
Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms.
Dimensions are subject to change without notice.
TC9308-4
23
FORGED STEEL EXTENDED BODY GATES
BOLTED AND WELDED BONNET CONVENTIONAL PORT
CLASS 800 TO 1500
SIZES: 1/2” TO 2”
Design and Manufacturing Standards
Valve Design: API 602
Pipe Threads, General Purpose, Inch: ASME B1.20.1
Socket Welding : ASME B16.11
Tested in Accordance With: API 598
Recommended Spare Parts*
D
Available Ends
Socket Weld
B
Threaded
WELDED BONNET
BOLTED BONNET
C
A
B
Integrally Reinforced
Lip End
A
Integrally Reinforced
Contoured End
B
B
A
A
TC9308-4
24
Class 800 and 1500 Extended Body
Bolted and Welded Bonnet Gate
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/2
40
2
50
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/2
40
2
50
Class 800 IR Contoured End
A
B
C
D
Wt.
Class 800 IR - Lip End
A
B
C
D
Wt.
A
Class 800 Threaded
B
C
D
Wt.
Class 800 Socket Weld
A
B
C
D
Wt.
41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45
8.6
207
8.6
218
9.6
245
10.4
263
11.4
289
A
0.39 5.9
9.9 150
0.55 6.1
13.9 155
0.71 7.3
18 185
1.14 10.2
28.9 259
1.44 10.8
36.6 274
3.2
81
3.2
81
3.9
99
5.5
140
5.5
140
6
3
7
3
10
5
19
9
29
13
Class 1500 Re-Out-Forced
B
C
D
Wt.
8.6
207
8.6
218
9.6
245
10.4
263
11.4
289
A
0.39 5.9
9.9 150
0.55 6.1
13.9 155
0.71 7.3
18 185
1.14 10.2
28.9 259
1.44 10.8
36.6 274
3.2
81
3.2
81
3.9
99
5.5
140
5.5
140
6
3
7
3
10
5
19
9
29
13
Class 1500 Re-In Forced
B
C
D
Wt.
5.6
141.5
5.8
146.5
6.5
166
7.5
191
8.5
216
A
0.39 6.4
10 162
0.55 7.3
14 185
0.7 7.6
18 192
1.14 10
29 255
1.44 10.7
36.5 273
3.1
80
3.9
100
3.9
100
5.5
140
6.7
170
5.7 5.6 0.39 6.4
2.6 141.5 10 162
6.4 5.8 0.55 7.3
2.9 146.5 14 185
9.5 6.5 0.7 7.6
4.3 166 18 192
19.4 7.5 1.14 10
8.8 191 29 255
28.6 8.5 1.44 10.7
13 216 36.5 273
Class 1500 Threaded
B
C
D
Wt.
A
3.1
80
3.9
100
3.9
100
5.5
140
6.7
170
5.7
2.6
6.4
2.9
9.5
4.3
19.4
8.8
28.6
13
Class 1500 Socket Weld
B
C
D
Wt.
41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45 41 45
8.6
218
9.6
245
10.4
264
10.5
267
12.8
325
TC9308-4
0.39 5.4
9.9 138
0.55 6.3
13.9 161
0.75 8.6
19 218
1.16 9.4
29.5 238
1.44 10.9
36.6 276
3.2
80
3.9
100
4.7
120
5.5
140
6.7
170
6
3
10
5
15
7
25
11
35
16
8.6
218
9.6
245
10.4
264
10.5
267
12.8
325
0.39 5.4
9.9 138
0.55 6.3
13.9 161
0.75 8.6
19 218
1.16 9.4
29.5 238
1.44 10.9
36.6 276
3.2
80
3.9
100
4.7
120
5.5
140
6.7
170
6
3
10
5
15
7
25
11
35
16
25
5.7
146
6.5
166
7.5
191
8.5
216
9.8
250
0.39 6.5 3.2 6.4
10 165 80 2.9
0.55 7.1 3.9 9.5
14 180 100 4.3
0.7 9.4 5.5 19.4
18 240 140 8.8
1.14 10.6 6.7 29.7
29 270 170 13.5
1.44 12.6 10.2 41.1
36.5 320 260 18.7
5.7
146
6.5
166
7.5
191
8.5
216
9.8
250
0.39 6.5 3.2 6.4
10 165 80 2.9
0.55 7.1 3.9 9.5
14 180 100 4.3
0.7 9.4 5.5 19.4
18 240 140 8.8
1.14 10.6 6.7 29.7
29 270 170 13.5
1.44 12.6 10.2 41.1
36.5 320 260 18.7
Typical Bill of Materials (See page 61 for available materials.)
Component
Material
ASTM Spec
Body
Carbon Steel
A105N
Bonnet
Carbon Steel
A105N
* Packing
Graphite W/Braided Carbon Fiber End Rings
* Gasket
Stainless Steel 316 Graphite
Stem
Stainless Steel
A479-410
Wedge
Stainless Steel
13 Chrome
Seat Rings
Stainless Steel
A479-410
Bonnet Bolt
Alloy Steel
A193 B7
Handwheel Nut
Carbon Steel
Commercial
Nameplate
Aluminum
Commercial
Handwheel
Carbon Steel
A105N
Yoke Sleeve
Stainless Steel
AISI 416
Gland Nuts
Carbon Steel
A194 2H
Gland Flange
Carbon Steel
A105N
Gland Studs
Stainless Steel
AISI 410
Packing Gland
Stainless Steel
A479-316
Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms.
Dimensions are subject to change without notice.
TC9308-4
26
FORGED STEEL FLANGED END GATES
BOLTED AND WELDED BONNET CONVENTIONAL PORT
CLASS 150 TO 1500
SIZES: 1/2” TO 2” (15MM TO 50MM)
(1/4” AND 3/8” AVAILABLE UPON REQUEST)
Design and Manufacturing Standards
Valve Design: API 602
Flange Dimensions: ASME B16.5
Face to Face Dimensions: ASME B16.10
Tested in Accordance With: API 598
Recommended Spare Parts*
BOLTED BONNET
C
WELDED BONNET
D
B
A
TC9308-4
27
Class 150 to 1500
Bolted and Welded Bonnet Flanged Gates
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
TC9308-4
A
41
B
45
4.3
108
4.6
118
5.0
127
5.5
140
6.5
165
7.0
178
41
45
41
45
0.39
10
0.55
14
0.71
18
0.94
24
1.22
30
1.44
37
0.39
10
0.55
14
0.71
18
0.95
24
1.14
29
1.44
37
6.8
173
7.1
180
8.1
205
9.3
235
10.2
260
11.7
296
4.9
125
5.2
132
6.7
170
7.6
193
8.3
211
9.3
236
A
41
D
41
41
45
41
45
0.39
10
0.55
14
0.71
18
0.94
24
1.22
30
1.44
37
0.39
10
0.55
14
0.71
18
0.95
24
1.14
29
1.44
37
6.9
174
7.1
180
8.1
205
10.2
260
10.4
265
11.7
296
4.9
125
5.2
132
6.7
170
7.6
193
8.3
211
9.3
236
28
Wt.
45
3.2
80
3.2
80
4.0
100
4.8
120
5.5
140
5.5
170
Class 300 BB and WB
C
B
45
5.5
140
6.0
153
6.5
165
7.0
178
7.5
191
8.5
216
Class 150 BB and WB
C
41
45
6.8
3.1
8.6
4
12.1
5.7
18.1
8.2
23.4
10.5
32.0
15.4
6.6
3
7.7
3.5
12.1
5.5
15
6.8
22.9
10.4
31.7
14.4
D
41
Wt.
45
3.2
80
3.2
80
3.9
100
4.7
140
5.5
140
6.7
170
41
45
7.3
4
10.8
5.4
14.7
6.5
21.1
12.5
29.5
13
35.9
17.5
7.9
3.6
10.8
4.9
15.4
7
20.7
9.4
29.3
13.3
39.6
18
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
TC9308-4
A
41
45
6.5
165
7.5
191
8.5
216
9.0
229
9.5
241
11.5
292
41
45
41
45
0.39
10
0.55
14
0.71
18
1.14
29
1.22
30
1.44
37
0.39
10
0.55
14
0.71
18
0.95
24
1.14
29
1.44
37
5.7
145
6.1
155
7.3
185
9.8
248
9.8
248
10.7
273
4.9
125
5.2
132
6.7
170
7.6
193
8.3
211
9.3
236
A
41
D
41
41
45
41
45
0.55
14
0.71
18
0.94
24
1.44
36.5
1.57
40
0.55
14
0.55
14
0.71
18
0.95
24
1.14
29
1.44
37
8.3
210
10.0
255
10.8
275
15
380
15.3
388
7.8
198
7.8
198
8.6
218
9.3
236
10.8
274
12.6
320
29
Wt.
45
3.2
80
3.2
80
4.0
100
5.5
140
5.5
140
5.6
170
Class 1500 BB and WB
C
B
45
8.5
216
9
229
10
254
12
305
14.5
368
Class 600 BB and WB
C
B
41
45
7.7
4.2
11.7
5.6
15.7
7.2
30.9
14.5
30.9
14.5
40.8
18
9.2
4.2
12.8
5.8
19.4
8.8
26.6
12.1
34.3
15.6
34.3
19.5
D
41
Wt.
45
3.9
100
4.7
120
5.5
140
6.8
172
10.2
260
41
45
22
10
33
15
37.4
17
77
35
121
55
9
4
9.5
4.3
13.5
6
19.2
8.7
26.9
12
39
17.7
Typical Bill of Materials (See page 61 for available materials)
Component
Material
ASTM Spec
Body
Carbon Steel
A105N
Bonnet
Carbon Steel
A105N
* Packing
Graphite W/Braided Carbon Fiber End Rings
* Gasket
Stainless Steel 316 Graphite
Stem
Stainless Steel
A479-410
Wedge
Stainless Steel
13 Chrome
Seat Rings
Stainless Steel
A479-410
Bonnet Bolt
Alloy Steel
A193 B7
Handwheel Nut
Carbon Steel
Commercial
Nameplate
Aluminum
Commercial
Handwheel
Carbon Steel
A105N
Yoke Sleeve
Stainless Steel
AISI 416
Gland Nuts
Carbon Steel
A194 2H
Gland Flange
Carbon Steel
A105N
Gland Studs
Stainless Steel
AISI 410
Packing Gland
Stainless Steel
A479-316
Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms.
Larger sizes available on request.
Dimensions are subject to change without notice.
TC9308-4
30
FORGED STEEL HIGH PRESSURE WELDED BONNET GATE
CONVENTIONAL PORT
CLASS 4500
SIZES: 1/2” TO 2” (15MM TO 50MM)
Design and Manufacturing Standards
Valve Design: ASME B16.34
Pipe Threads, General Purpose, Inch: ASME B1.20.1
Socket Welding: ASME B16.11
Tested in Accordance With: API 598
Recommended Spare Parts*
D
C
B
A
TC9308-4
31
Size
A
4.7
120
5.1
130
5.1
130
8.3
210
8.3
210
9.4
240
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
B
0.47
12
0.47
12
0.47
12
0.63
16
0.63
16
0.83
21
Class 4500
Welded Bonnet Gate
C
10.4
265
10.4
265
10.4
265
12.4
315
12.4
315
15.4
390
D
5.5
140
5.5
140
6.7
170
6.7
170
10.2
260
10.2
260
Wt.
17.6
8
19.8
9
19.8
9
31.9
14.5
33
15
41.8
19
Typical Bill of Materials (See page 61 for available materials)
Component
Material
ASTM Spec
Body
Carbon Steel
A105N
Bonnet
Carbon Steel
A105N
* Packing
Graphite W/Braided Carbon Fiber End Rings
* Gasket
Stainless Steel 316 Graphite
Stem
Stainless Steel
A479-410
Wedge
Stainless Steel
13 Chrome
Seat Rings
Stainless Steel
A479-410
Bonnet Bolt
Alloy Steel
A193 B7
Handwheel Nut
Carbon Steel
Commercial
Nameplate
Aluminum
Commercial
Handwheel
Carbon Steel
A105N
Yoke Sleeve
Stainless Steel
AISI 416
Gland Nuts
Carbon Steel
A194 2H
Gland Flange
Carbon Steel
A105N
Gland Studs
Stainless Steel
AISI 410
Packing Gland
Stainless Steel
A479-316
Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms.
Larger sizes available on request.
Dimensions are subject to change without notice.
TC9308-4
32
II. FORGED STEEL BOLTED AND WELDED BONNET GLOBE VALVES
SIZES: 1/2” TO 2” (15MM TO 50MM) • PRESSURE CLASS: 150 TO 4500
Cameron’s Typical NEWCO Forged Steel Bolted and Welded Bonnet Globe Valve Expanded View
1
2
3
4
13
5
6
7
14
15
8
8
4
9
10
11
12
16
17
18
19
20
TC9308-4
33
1. Handwheel Nut: The handwheel nut secures the handwheel to the bonnet assembly.
2. Handwheel Washer: The washer helps to prevent loosening.
3. Handwheel: The handwheel cycles the valve.
4. & 14. Gland Bolts and Nuts: The gland bolts and nuts allow for easy adjustments for
packing compression.
5. Gland Flange: The gland flange applies pressure to the gland for accurate packing compression.
6. Gland: The gland compresses the packing to create a stem seal above the back seat
between the bonnet and stem.
7. Packing: The packing creates a seal above the back seat between the bonnet and stem.
8. Bonnet Bolts: The bonnet bolts secure the bonnet to the body.
9. Bonnet: Cameron’s NEWCO bonnet assemblies are built to the same standards as the
bodies.
10. Bonnet Gasket: The bonnet gasket creates a leakproof seal between the bonnet and
body.
11. Body: Cameron’s NEWCO forged steel bodies provide low resistance flow and optimum strength and performance
12. Seat Ring: To ensure a stable shutoff, the seat ring is aligned into the valve, then precision ground for optimal seating.
13. Stem Nut: The stem nut provides a precision guide for proper stem alignment.
15. Stuffing Box: The stuffing box contains the packing.
16. Stem: The stem inserts vertically into the disc.
17. Lock Groove: The lock groove receives the split lock ring which allows the disc nut to
lift the disc during cycling.
18. Disc Nut: The disc nut, in conjunction with the split lock ring, secures the disc to the
stem.
19. Split Ring: The split ring allows the disc nut to lift the disc during cycling.
20. Disc: Cameron’s NEWCO plug type disc is machined to the tightest tolerances to ensure trouble free shutoff and cycling.
TC9308-4
34
FORGED STEEL BOLTED AND WELDED BONNET GLOBES
THREADED, SOCKET WELD AND BUTTWELD ENDS CONVENTIONAL PORT
CLASS 800 TO 2500
SIZES: 1/2” TO 2” (15MM TO 50MM)
(1/4” AND 3/8” AVAILABLE UPON REQUEST)
Design and Manufacturing Standards
Valve Design: API 602
Pipe Threads, General Purpose, Inch: ASME B1.20.1
Socket Welding: ASME B16.11
Tested in Accordance With: API 598
Recommended Spare Parts*
BOLTED BONNET
C
WELDED BONNET
D
B
A
TC9308-4
35
Class 800 to 1500
Bolted and Welded Bonnet Globes
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
A
Class 800 WB
C
B
41
45
3.2
80
3.5
90
4.3
110
5
127
6.1
155
6.7
170
3.1
78.7
3.6
91.4
4.4
111.8
4.7
119.4
6
152.4
6.8
172.7
41
45
0.35
9
0.49
12.5
0.68
17.5
0.88
22.5
1.14
29
1.37
35
A
B
D
Wt.
A
B
41
45
41
45
41
45
41
45
6.3
160
6.7
170
7.9
200
9.3
235
9.3
270
11.4
290
5.2
132.1
5.4
137.2
7
177.8
8.3
210.8
8.4
213.4
10.3
261.6
3.2
80
3.2
80
3.9
100
4.7
120
5.5
140
6.7
170
3.3
83.8
3.3
83.8
4.7
119.4
5.9
149.9
5.9
149.9
6.7
170.2
4
1.8
4.4
2
7.3
3.3
11.9
5.4
17.4
7.9
23.8
10.8
2.9
1.3
3.7
1.7
6.4
2.9
15.9
7.2
14.9
6.8
23.4
10.6
3.2
80
3.5
90
4.3
110
5
127
6.1
155
6.7
170
3.1
78.7
3.6
91.4
4.4
111.8
4.7
119.4
6
152.4
6.8
172.7
Class 1500 WB
C
D
Wt.
Class 800 BB
C
41
45
0.35
9
0.49
12.5
0.68
17.5
0.88
22.5
1.14
29
1.37
35
A
B
D
Wt.
41
45
41
45
41
45
6.3
160
6.7
170
7.9
200
9.3
235
9.3
270
11.4
290
5.2
132.1
5.4
137.2
7
177.8
8.3
210.8
8.4
213.4
10.3
261.6
3.2
80
3.2
80
3.9
100
4.7
120
5.5
140
6.7
170
3.3
83.8
3.3
83.8
4.7
119.4
5.9
149.9
5.9
149.9
6.7
170.2
4
1.8
4.4
2
7.3
3.3
11.9
5.4
17.4
7.9
23.8
10.8
2.9
1.3
3.7
1.7
6.4
2.9
15.9
7.2
14.9
6.8
23.4
10.6
Class 1500 BB
C
D
Wt.
41
45
41
45
41
45
41
45
41
45
41
45
41
45
41
45
41
45
41
45
3.5
90
4.3
110
4.7
120
5.1
130
6.7
170
8.3
210
4.4
111.8
4.4
111.8
5.1
129.5
5.9
149.9
6.8
172.7
8.7
220.9
0.35
9
0.43
11
0.57
14.5
0.75
19
1.06
27
1.22
31
0.39
9.9
0.51
12.95
0.66
16.76
0.9
22.86
1.18
29.97
1.49
37.85
6.5
165
7.7
195
9.3
235
10.4
265
11
280
13.2
335
8.1
205.7
8.1
205.7
9.4
238.8
10.2
259.1
11.4
289.6
13.3
337.8
3.2
80
4.7
120
5.5
140
5.5
140
6.7
170
6.7
170
4.9
124.5
4.9
124.5
6.2
157.5
6.2
157.5
6.2
157.5
7.1
180.3
4.2
1.9
7
3.2
12.1
5.5
17.6
8
24.2
11
39.6
18
4.4
2
8.4
3.8
9.3
4.2
17.6
8
29.1
13.2
37
16.8
3.5
90
4.3
110
4.7
120
5.1
130
6.7
170
8.3
210
4.4
111.8
4.4
111.8
5.1
129.5
5.9
149.9
6.8
172.7
8.7
220.9
0.35
9
0.43
11
0.57
14.5
0.75
19
1.06
27
1.22
31
0.39
9.9
0.51
12.95
0.66
16.76
0.9
22.86
1.18
29.97
1.49
37.85
6.5
165
7.7
195
9.1
230
10.2
260
11.2
285
13
330
8.1
205.7
8.1
205.7
9.4
238.8
10.2
259.1
11.4
289.6
13.3
337.8
3.2
80
4.7
120
5.5
140
5.5
140
6.7
170
6.7
170
4.9
124.5
4.9
124.5
6.2
157.5
6.2
157.5
6.2
157.5
7.1
180.3
4.4
2
7.3
3.3
12.1
5.5
19.8
9
26.4
12
39.6
18
4.4
2
8.4
3.8
9.3
4.2
17.6
8
29.1
13.2
37
16.8
TC9308-4
36
Size
In.
A
----mm 41 45
1/2
4.3
15
110
3/4
4.7
20
120
1
5.1
25
130
1-1/4
8.3
32
210
1-1/2
8.3
40
210
2
9.5
50
240
Class 2500 WB
C
B
41
45
0.43
11
0.55
14
0.75
19
0.94
24
1.1
28
1.42
36
41
45
7.7
195
8.9
225
10
255
12.8
325
13
330
14.6
370
D
41
Wt.
45
4.7
120
5.5
140
5.5
140
6.7
170
6.7
170
10.2
260
41
45
A
41
8.6
3.9
14.1
6.4
19.9
9
44
20
48.4
22
61.6
28
45
4.3
110
4.7
120
5.1
130
8.3
210
8.3
210
9.5
240
Class 2500 BB
C
B
41
45
0.43
11
0.55
14
0.75
19
0.94
24
1.1
28
1.42
36
41
45
10.6
270
10.8
275
11.4
290
15.4
390
16.3
415
16.7
425
D
41
Wt.
45
4.7
120
5.5
140
5.5
140
6.7
170
10.2
260
10.2
260
Typical Bill Materials (See page 61 for available materials)
Component
Material
ASTM Spec
Body
Carbon Steel
A105N
Bonnet
Carbon Steel
A105N
* Packing
Graphite W/Braided Carbon Fiber End Rings
* Gasket
Stainless Steel 316 Graphite
Stem
Stainless Steel
A479-410
Disc
Stainless Steel
13 Chrome
Seat Rings
Stainless Steel
A479-410
Bonnet Bolt
Alloy Steel
A193 B7
Washer
Carbon Steel
Commercial
Handwheel Nut
Carbon Steel
Commercial
Nameplate
Aluminum
Commercial
Handwheel
Carbon Steel
Commercial
Yoke Sleeve
Stainless Steel
AISI 416
Gland Nuts
Carbon Steel
A194 2H
Gland Flange
Carbon Steel
A105N
Gland Studs
Stainless Steel
AISI 410
Packing Gland
Stainless Steel
AISI 416
Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms.
Larger sizes available on request.
Dimensions are subject to change without notice.
TC9308-4
37
41
45
11
5
17.6
8
23.5
10.7
52.8
24
70.4
32
81.4
37
FORGED STEEL FLANGED END GLOBES
BOLTED AND WELDED BONNET CONVENTIONAL PORT
CLASS 150 TO 1500
SIZES: 1/2” TO 2” (15MM TO 50MM)
(1/4” AND 3/8” AVAILABLE UPON REQUEST)
Design and Manufacturing Standards
Valve Design: API 602
Flange Dimensions: ASME B16.5
Face to Face Dimensions: ASME B16.10
Tested in Accordance With: API 598
Recommended Spare Parts*
BOLTED BONNET
C
WELDED BONNET
D
B
A
TC9308-4
38
Class 150 to 1500
Bolted and Welded Bonnet Flanged Globes
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/2
40
2
50
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/2
40
2
50
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/2
40
2
50
TC9308-4
A
41
45
4.25
108
4.63
118
5.00
127
6.50
165
8.00
203
41
45
41
45
0.35
9
0.47
12.5
0.67
17.5
1.10
29
1.34
35
0.39
9.9
0.39
9.9
0.69
17.5
1.18
30
1.46
37.1
7.3
185
7.6
192
8.7
220
10.4
265
12.2
310
6.8
173
7.0
178
8.3
211
9.2
234
10.4
264
A
41
6.00
152.5
7.00
178
8.00
203
9.00
229
10.5
267
41
45
41
45
0.35
9
0.47
12.5
0.67
17.5
1.10
29
1.34
35
0.39
9.9
0.39
9.9
0.69
17.5
1.18
30
1.46
37.1
6.3
160
6.6
168
7.9
200
10.6
268
11.4
290
6.26
159
6.26
159
7.6
193
9.2
234
10.4
264
A
6.50
165
7.50
190.5
8.50
216
9.51
241.5
11.5
292
41
41
45
41
45
0.35
9
0.47
12.5
0.67
17.5
1.10
29
1.34
35
0.39
9.9
0.39
9.9
0.69
17.5
1.18
30
1.46
37.1
6.3
160
6.6
168
7.9
200
10.6
268
11.4
290
6.26
159
6.26
159
7.6
193
8.7
221
10.4
264
39
Wt.
45
3.1
80
3.1
80
4.0
100
5.5
140
6.7
170
41
45
7
3.1
8
4
17
5.7
25
10.6
35
15.4
9.9
4.5
15.2
6.9
21.6
9.8
42.9
19.5
61.6
28
D
41
Wt.
45
3.1
80
3.1
80
4.0
100
5.5
140
6.7
170
Class 600 BB and WB
C
B
45
D
Class 300 BB and WB
C
B
45
41
Class 150 BB and WB
C
B
41
45
8
3.5
11
4.8
15
7.2
30
14.5
40
18
10.6
4.8
16.9
7.7
24.2
11
46.6
21.2
71.7
32.6
D
41
Wt.
45
3.1
80
3.1
80
4.0
100
5.5
140
6.7
170
41
45
8.2
3.7
11.7
5.3
18.1
8.2
33.1
15
47.4
21.5
12.3
5.6
17.2
7.8
27.5
12.5
51.7
23.5
85.4
38.8
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
A
41
45
8.5
216
9.0
229
10.0
254
11.0
279
12.0
305
14.5
368
Class 1500 BB and WB
C
B
D
Wt.
41
45
41
45
41
45
41
45
.43
11
.57
14.5
.75
19
1.22
31
1.48
37.5
0.5
13
0.7
18
0.9
24
1.1
29
1.4
36.5
1.8
46.5
8.86
225
10.63
270
11.22
285
15.75
400
16.54
420
8.1
207
9.4
240
10.2
258
11.4
290
13.3
337
14.0
354
4.72
120
5.51
140
5.51
140
6.69
170
10.24
260
3.93
100
4.92
125
6.29
160
6.29
160
7.08
180
9.45
240
22.0
10.0
33.0
15.0
37.4
17.0
79.2
36.0
121.0
55.0
17.6
8.0
29.0
13.2
38.3
17.4
42.0
19.0
54.0
24.5
68.2
31.0
Typical Bill Materials (See page 61 for available materials)
Component
Material
ASTM Spec
Body
Carbon Steel
A105N
Bonnet
Carbon Steel
A105N
* Packing
Graphite W/Braided Carbon Fiber End Rings
* Gasket
Stainless Steel 316 Graphite
Stem
Stainless Steel
A479-410
Disc
Stainless Steel
13 Chrome
Seat Rings
Stainless Steel
A479-410
Bonnet Bolts
Alloy Steel
A193 B7
Washer
Carbon Steel
Commercial
Handwheel Nut
Carbon Steel
Commercial
Nameplate
Aluminum
Commercial
Handwheel
Carbon Steel
Commercial
Yoke Sleeve
Stainless Steel
AISI 416
Gland Nuts
Carbon Steel
A194 2H
Gland Flange
Carbon Steel
A105N
Gland Studs
Stainless Steel
AISI 410
Packing Gland
Stainless Steel
AISI 416
Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms.
Larger sizes available on request.
Dimensions are subject to change without notice.
TC9308-4
40
FORGED STEEL Y-PATTERN BOLTED AND WELDED BONNET GLOBE
CONVENTIONAL PORT
CLASS 800 TO 2680
SIZES: 1/2” TO 2” (15MM TO 50MM)
(1/4” AND 3/8” AVAILABLE UPON REQUEST)
Design and Manufacturing Standards
Valve Design: ASME B16.34
Pipe Threads, General Purpose, Inch: ASME B1.20.1
Socket Welding: ASME B16.11
Tested in Accordance With: API 598
Recommended Spare Parts*
BOLTED BONNET
WELDED BONNET
D
C
B
A
TC9308-4
41
A
3.6
92
3.6
92
4.4
111
6
152
6
152
6.8
172
Class 800
Bolted and Welded Bonnet Globe
B
C
D
0.39
7.5
3.7
10
190
95
0.51
7.5
3.7
13
190
95
0.69
9.3
4.3
17.5
235
110
0.94
11.2
5.5
24
286
140
1.22
11.2
5.5
31
286
140
1.46
12.8
6.7
37
325
200
Wt.
4.4
2
4.4
2
9
4.1
19.8
9
19.8
9
30.4
13.8
A
3.9
100
4.3
110
4.9
125
5.9
150
6.3
160
7.5
190
B
0.51
13
0.69
17.5
0.89
22.5
1.1
28
1.38
35
1.73
44
Class 1500 and 1690
Welded Bonnet Globe
C
7.3
185
9.1
230
9.4
240
12
305
13.4
340
15.7
400
D
3.9
100
5.5
140
5.5
140
6.7
170
7.9
200
10.2
260
Wt.
6.6
3
8.8
4
11
5
20.9
9.5
24.2
11
37.4
17
B
0.47
12
0.59
15
0.79
20
0.98
25
1.22
31
1.49
38
Class 2500 and 2680
Welded Bonnet Globe
C
9.1
230
9.4
240
12
305
12
305
13.6
345
15.7
400
D
4.7
120
5.5
140
6.7
170
6.7
170
7.9
200
10.2
260
Wt.
8.8
4
11
5
20.9
9.5
23.1
10.5
37.4
17
50.6
23
Size
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
Size
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
Size
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
TC9308-4
A
3.9
100
4.9
125
6.3
160
6.3
160
7.5
190
8.3
210
42
Typical Bill of Materials (See page 61 for available materials)
Component
Material
ASTM Spec
Body
Carbon Steel
A105N
Bonnet
Carbon Steel
A105N
* Packing
Graphite W/Braided Carbon Fiber End Rings
* Gasket
Stainless Steel 316 Graphite
Stem
Stainless Steel
A479-410
Disc
Stainless Steel
13 Chrome
Seat Rings
Stainless Steel
A479-410
Bonnet Bolts
Alloy Steel
A193 B7
Washer
Carbon Steel
Commercial
Handwheel Nut
Carbon Steel
Commercial
Nameplate
Aluminum
Commercial
Handwheel
Carbon Steel
Commercial
Yoke Sleeve
Stainless Steel
AISI 416
Gland Nuts
Carbon Steel
A194 2H
Gland Flange
Carbon Steel
A105N
Gland Studs
Stainless Steel
AISI 410
Packing Gland
Stainless Steel
AISI 416
Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms.
Larger sizes available on request.
Dimensions are subject to change without notice.
TC9308-4
43
FORGED STEEL HIGH PRESSURE WELDED BONNET GLOBE
CONVENTIONAL PORT
CLASS 4500
SIZES: 1/2” TO 2” (15MM TO 50MM)
Design and Manufacturing Standards
Valve Design: ASME B16.34
Pipe Threads, General Purpose, Inch: ASME B1.20.1
Socket Welding: ASME B16.11
Tested in Accordance With: API 598
Recommended Spare Parts*
D
C
B
A
Size
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
TC9308-4
A
4.7
120
6.1
155
6.1
155
8.3
210
8.3
210
9.4
240
B
0.31
8
0.47
12
0.59
15
0.79
20
0.98
25
1.1
28
Class 4500
Welded Bonnet Globe
C
8.9
228
10.8
275
11
280
16.1
410
16.1
410
16.5
420
44
D
4.7
120
5.5
140
5.5
140
10.2
260
10.2
260
10.2
260
Wt.
17.6
8
4
11
41.8
19
50.6
23
50.6
23
50.6
23
Typical Bill of Materials (See page 61 for available materials)
TC9308-4
Component
Material
ASTM Spec
Body
Carbon Steel
A105N
Bonnet
Carbon Steel
A105N
* Packing
Graphite W/Braided Carbon Fiber End Rings
* Gasket
Stainless Steel 316 Graphite
Stem
Stainless Steel
A479-410
Disc
Stainless Steel
13 Chrome
Seat Rings
Stainless Steel
A479-410
Bonnet Bolts
Alloy Steel
A193 B7
Washer
Carbon Steel
Commercial
Handwheel Nut
Carbon Steel
Commercial
Nameplate
Aluminum
Commercial
Handwheel
Carbon Steel
Commercial
Yoke Sleeve
Stainless Steel
AISI 416
Gland Nuts
Carbon Steel
A194 2H
Gland Flange
Carbon Steel
A105N
Gland Studs
Stainless Steel
AISI 410
Packing Gland
Stainless Steel
AISI 416
45
D
C
B
A
Size
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
A
4.9
125
6.3
160
7.5
190
7.5
190
8.3
210
11
280
Class 4500
Welded Bonnet Y-Pattern Globe
B
C
D
0.31
9.4
5.5
8
240
140
0.43
11.2
6.7
11
285
170
0.59
12.6
7.9
15
320
200
0.71
12.6
7.9
18
320
200
0.79
12.6
10.2
20
360
260
0.98
17.7
14.6
25
450
370
Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms.
Larger sizes available on request.
Dimensions are subject to change without notice.
TC9308-4
46
Wt.
12.1
5.5
22
10
37.4
17
37.4
17
41.8
19
52.8
24
III. FORGED STEEL BOLTED AND WELDED BONNET CHECK VALVES
SIZES: 1/2” TO 2” (15MM TO 50MM) • PRESSURE CLASS: 150 TO 1500
Cameron’s Typical NEWCO Forged Steel Bolted Check Valve Expanded View
2
3
4
5
6
7
1
TC9308-4
47
1. Body: Cameron’s NEWCO forged steel bodies provide low resistance flow and optimum
strength and performance.
2. Cover Studs: The cover studs secure the bonnet to the body.
3. Cover: The cover allows access to internal components.
4. Spring: The spring is precision made and loaded for precise pressures.
5. Piston: Cameron’s NEWCO piston is machined to the tightest tolerances to ensure
trouble free shutoff and cycling.
6. Cover Gasket: The cover gasket creates a leak-proof seal between the bonnet and the
body.
7. Seat: The seat ensures a stable shutoff. The seat is precision ground for optimal seating.
TC9308-4
48
FORGED STEEL LIFT AND SWING CHECKS
BOLTED AND WELDED COVER CONVENTIONAL PORT
CLASS 800 TO 1500
SIZES: 1/2” TO 2” (15MM TO 50MM)
(1/4” AND 3/8” AVAILABLE UPON REQUEST)
Design and Manufacturing Standards
Valve Design: API 602
Pipe Threads, General Purpose, Inch: ASME B1.20.1
Socket Welding: ASME B16.11
Tested in Accordance With: API 598
BOLTED
BONNET
C
WELDED
BONNET
Recommended Spare Parts*
B D
BOLTED
BONNET
C
WELDED
BONNET
A
B
D
A
TC9308-4
49
Class 800 to 1500
Bolted and Welded Bonnet – Lift and Swing Check
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
A
B
Class 800 BB Lift
C
D
41
45
41
45
41
45
3.2
80
3.5
90
4.3
110
5
127
6.1
155
6.7
170
3.1
78.7
3.6
91.4
4.4
111.8
4.7
119.4
6
152.4
6.8
172.7
0.35
9
0.49
12.5
0.68
17.5
0.88
22.5
1.14
29
1.38
35
0.39
9.9
0.54
13.9
0.69
17.5
0.9
22.9
1.18
29.9
1.45
36.8
1.9 1.9
49
49
2.2 2.1
55 53.3
2.8 2.7
70 68.6
3
3.3
77 83.8
4.1 3.7
105 94
4.7 4.4
120 111.8
45
0.85
21.6
1.07
27.2
1.33
33.8
1.67
42.4
1.92
48.8
2.41
61.2
Class 800 WB Lift
B
C
D
A
41
45
41
45
41
3.2
80
3.5
90
4.3
110
5
127
6.1
155
6.7
170
3.1
78.7
3.6
91.4
4.4
111.8
4.7
119.4
6
152.4
6.8
172.7
0.35
9
0.49
12.5
0.68
17.5
0.88
22.5
1.14
29
1.38
35
0.39
9.9
0.54
13.9
0.69
17.5
0.9
22.9
1.18
29.9
1.45
36.8
1.9 1.9
49
49
2.2 2.1
56 53.3
2.7 2.7
69 68.6
3.2 3.3
80 83.8
3.7 3.7
95
94
4.1 4.4
105 111.8
TC9308-4
41
Wt.
45
41
41
A
0.85
21.6
1.07
27.2
1.33
33.8
1.67
42.4
1.92
48.8
2.41
61.2
Class 800 BB Swing
C
D
45
41
45
41
45
41
45
2.4 2.1
1.1
1
4
2.6
1.8 1.2
5.7 4.3
2.6
2
7.9 11.5
3.6 5.2
12.1 9.9
5.5 4.5
18.5 17
8.4 7.7
3.2
80
3.5
90
4.3
110
5
127
5
127
5.1
130
3.1
78.7
3.6
91.4
4.4
111.8
4.7
119.4
4.7
119.4
5.5
139.7
0.35
9
0.49
12.5
0.68
17.5
0.88
22.5
1.14
29
1.44
36.6
0.39
9.9
0.55
13.9
0.71
18
0.95
24.1
1.14
29
1.44
36.6
1.9
49
2.2
55
2.8
70
3
77
4.1
105
4.7
119
1.6
40.6
1.8
45.7
2.3
58.4
3.3
83.8
3.1
78.7
3.7
94
Wt.
45
B
41
45
0.85
21.6
1.07
27.2
1.33
33.8
1.67
42.4
1.92
48.8
2.41
61.2
Class 800 WB Swing
B
C
D
A
45
41
45
41
45
41
45
2
2.1
0.9
1
2.6 2.6
1.2 1.2
4.6 4.3
2.1
2
7.5 11.5
3.4 5.2
11.7 9.9
5.3 4.5
17.2 17
7.8 7.7
3.2
80
3.5
90
4.3
110
5
127
5
127
5.1
130
3.1
78.7
3.6
91.4
4.4
111.8
4.7
119.4
4.7
119.4
5.5
139.7
0.35
9
0.49
12.5
0.68
17.5
0.88
22.5
1.14
29
1.38
35
0.39
9.9
0.55
13.9
0.71
18
0.95
24.1
1.14
29
1.44
36.6
1.9
49
2.2
56
2.7
69
3.2
80
3.7
95
4.1
105
1.6
40.6
1.8
45.7
2.3
58.4
3.3
83.8
3.1
78.7
3.7
94
50
41
Wt.
41
41
45
2.4 2.1
1.1
1
4
2.5
1.8 1.1
5.7 3.9
2.6 1.8
7.9 10.6
3.6 4.8
12.1 8.8
5.5
4
19.6 13.2
8.9
6
Wt.
45
0.85
21.6
1.07
27.2
1.33
33.8
1.67
42.4
1.92
48.8
2.41
61.2
41
45
2
2.1
0.9
1
2.6 2.5
1.2 1.1
4.6 3.9
2.1 1.8
7.5 10.6
3.4 4.8
11.7 8.8
5.3
4
17.2 13.2
7.8
6
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/4
32
1-1/2
40
2
50
A
B
Class 1500 BB Lift
C
D
41
45
41
45
3.5
90
4.3
110
4.7
120
5.1
130
6.7
170
8.3
210
4.4
111.8
4.4
111.8
5.1
129.5
6.8
172.7
8.7
220.9
0.35
9
0.43
11
0.57
14.5
0.74
19
1.06
27
1.22
31
0.39
9.9
0.51
12.95
0.66
16.76
1.18
29.97
1.49
37.85
A
B
45
2.2 3.1
55 78.7
2.8 3.1
70 78.7
3
3.8
77 96.5
4.1
105
4.5 4.7
115 119.4
5.7 5.5
145 139.7
41
45
0.85
21.6
1.07
27.2
1.33
33.8
1.67
42.4
1.92
48.8
2.41
61.2
Class 1500 WB Lift
C
D
41
45
41
45
3.5
90
4.3
110
4.7
120
5.1
130
6.7
170
8.3
210
4.4
111.8
4.4
111.8
5.1
129.5
6.8
172.7
8.7
220.9
0.35
9
0.43
11
0.57
14.5
0.74
19
1.06
27
1.22
31
0.39
9.9
0.51
12.95
0.66
16.76
1.18
29.97
1.49
37.85
TC9308-4
41
Wt.
41
45
2.2 3.1
55 78.7
2.8 3.1
70 78.7
3.2 3.8
80 96.5
3.5
90
3.9 4.7
100 119.4
4.5 5.5
115 139.7
41
41
45
41
45
41
45
4.8
2.2
6.8
3.1
9.2
4.2
12.8
5.8
20.7
9.4
26.6
12.1
7.5
3.4
10.6
4.8
15.2
6.9
19.4
8.8
27.1
12.3
3.5
90
4.3
110
4.7
120
5.1
130
5.1
130
8.3
210
4.4
111.8
4.4
111.8
4.5
114.3
5.5
139.7
6.4
162.6
0.35
9
0.43
11
0.57
14.5
0.74
19
1.06
27
1.22
31
0.55
13.97
0.55
13.97
0.71
18.03
1.14
28.95
1.44
36.57
Wt.
45
0.85
21.6
1.07
27.2
1.33
33.8
1.67
42.4
1.92
48.8
2.41
61.2
Class 1500 BB Swing
B
C
D
A
45
2.2 3.1
55 78.7
2.8 3.1
70 78.7
3
3.8
77 96.5
4.1
105
4.5 4.7
115 119.4
5.7 5.5
145 139.7
41
45
0.85
21.6
1.07
27.2
1.33
33.8
1.67
42.4
1.92
48.8
2.41
61.2
Class 1500 WB Swing
B
C
D
A
41
45
41
45
41
45
2.9
1.3
5.5
2.5
8.4
3.8
12.1
5.5
18.3
8.3
24.2
11
7.5
3.4
10.6
4.8
15.2
6.9
19.4
8.8
27.1
12.3
3.5
90
4.3
110
4.7
120
5.1
130
5.1
130
8.3
210
4.4
111.8
4.4
111.8
4.5
114.3
5.5
139.7
6.4
162.6
0.35
9
0.43
11
0.57
14.5
0.74
19
1.06
27
1.22
31
0.55
13.97
0.55
13.97
0.71
18.03
1.14
28.95
1.44
36.57
51
41
Wt.
41
45
2.2 3.1
55 78.7
2.8 3.1
70 78.7
3.2 3.8
80 96.5
3.5
90
3.9 4.7
100 119.4
4.5 5.5
115 139.7
41
41
45
4.8
2.2
6.8
3.1
9.2
4.2
12.8
5.8
20.7
9.4
26.6
12.1
7.9
3.6
9.5
4.3
23.5
10.7
27.7
12.6
34.1
15.5
Wt.
45
0.85
21.6
1.07
27.2
1.33
33.8
1.67
42.4
1.92
48.8
2.41
61.2
41
45
2.9
1.3
5.5
2.5
8.4
3.8
12.1
5.5
18.3
8.3
24.2
11
7.9
3.6
9.5
4.3
23.5
10.7
27.7
12.6
34.1
15.5
Typical Bill Materials (See page 61 for available materials)
Component
Material
ASTM Spec
Body
Carbon Steel
A105N
Seat Ring
Stainless Steel
A479-410
Piston
Stainless Steel
A479-410
Rivet
Brass
Commercial
Spring
Stainless Steel
A479-316
Nameplate
Aluminum
Commercial
* Gasket
Stainless Steel 316 W/Graphite Spiral Wound
Cap
Carbon Steel
A105N
Cap Bolt
Alloy Steel
A193-B7
Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms.
Larger sizes available on request.
Dimensions are subject to change without notice.
TC9308-4
52
FORGED STEEL LIFT AND SWING CHECKS
BOLTED AND WELDED COVER CONVENTIONAL PORT
CLASS 150 TO 1500
SIZES: 1/2” TO 2” (15MM TO 50MM)
(1/4” AND 3/8” AVAILABLE UPON REQUEST)
Design and Manufacturing Standards
Valve Design: ASME B16.34
Flange Dimensions: ASME B16.5
Face to Face Dimensions: ASME B16.10
Tested in Accordance With: API 598
BOLTED
BONNET
C
WELDED
BONNET
Recommended Spare Parts*
B D
BOLTED
BONNET
C
WELDED
BONNET
A
B
A
TC9308-4
53
D
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/2
40
2
50
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/2
40
2
50
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/2
40
2
50
TC9308-4
Class 150 to 1500
Bolted and Welded Bonnet - Lift and Swing Check
Class 150
B (Lift)
B (Swing)
C
A
41
45
41
45
4.3
108
4.6
118
5
127
6.5
165
8
203
0.35
9
0.49
12.5
0.68
17.5
1.14
29
1.37
35
A (Lift)
41
41
6
152.5
7
178
8
203
9
229
10.5
267
41
45
41
0.35
9
0.49
12.5
0.68
17.5
1.14
29
1.37
35
B (Lift)
45
6.5
165
7.5
191
8.5
216
9.5
241
11.5
292
45
41
45
0.35
9
0.49
12.5
0.68
17.5
1.14
29
1.37
35
41
45
2.8
70
3.2
80
3.6
92
3.9
100
5.5
140
1.6
40.6
1.8
45.7
2.3
58.4
3.1
78.7
3.7
94
Class 300
B (Swing)
B (Lift)
6
152.5
7
178
8.5
216
9.5
241
10.5
267
A
45
0.4
10
0.4
10
0.7
18
1.2
29.5
1.4
36.5
A (Swing)
45
41
41
45
0.4
10
0.6
14
0.7
18
1.2
30
1.4
36.5
Class 600
B (Swing)
41
45
0.4
10
0.6
14
0.7
18
1.2
30
1.4
36.5
54
D
Wt.
41
45
41
0.5
12.7
0.75
19.1
1
25.4
1.5
38.1
2
50.8
C
6.2
2.8
8.8
4
11.7
5.3
19.8
9
33
15
D
41
45
2
50
2.2
55
2.8
70
3.9
98
4.3
110
1.6
40.6
1.8
45.7
2.3
58.4
3.1
78.7
3.7
94
41
2
50
2.2
55
2.8
70
3.9
98
4.3
110
1.6
40.6
1.8
45.7
2.3
58.4
3.1
78.7
3.7
94
41
8.2
12
14.3
45
6.2
2.8
10.3
4.7
12.5
5.7
26
11.8
37.4
17
8.1
3.7
10.6
4.8
19.4
8.8
30.1
13.7
39.2
17.8
Wt.
45
0.5
12.7
0.75
19.1
1
25.4
1.5
38.1
2
50.8
4.4
41
D
45
3.4
Wt.
45
0.5
12.7
0.75
19.1
1
25.4
1.5
38.1
2
50.8
C
41
45
41
45
6.4
2.9
10.6
4.8
21.3
9.7
26.4
12
38.1
17.3
8.8
4
12.8
5.8
20.9
9.5
34.3
15.6
53.9
24.5
Size
In.
----mm
1/2
15
3/4
20
1
25
1-1/2
40
2
50
A
41
B (Lift)
45
8.5
216
9
229
10
254
12
305
14.5
368
41
45
0.43
11
0.57
14.5
0.74
19
1.22
31
1.48
37.5
Class 1500
B (Swing)
C
41
45
0.6
14
0.7
18
0.9
24
1.4
36
1.6
40
41
D
45
3.5
90
4.1
105
4.7
120
6.3
160
6.7
170
Wt.
41
45
41
0.5
12.7
0.69
17.5
0.87
22.1
1.37
34.8
1.87
47.5
Typical Bill Materials (See page 61 for available materials)
Component
Material
ASTM Spec
Body
Carbon Steel
A105N
Seat Ring
Stainless Steel
A479-410
Piston
Stainless Steel
A479-410
Rivet
Brass
Commercial
Spring
Stainless Steel
A479-316
Nameplate
Aluminum
Commercial
* Gasket
Stainless Steel 316 W/Graphite Spiral Wound
Cap
Carbon Steel
A105N
Cap Bolt
Alloy Steel
A193-B7
Note: Dimensions: Inches/Millimeters - Weights: Pounds/Kilograms.
Larger sizes available on request.
Dimensions are subject to change without notice.
TC9308-4
55
45
16.7
7.6
23.8
10.8
31.9
14.5
68.2
31
94.6
43
IV. FORGED STEEL CV VALUES GATES, GLOBES, CHECKS
Cameron’s
NEWCO
Forged Steel
Gate Valves
Cv Values
NPS
150 - 800
Full Bore
150 - 800
Reduced Bore
1500
Full Bore
1500
Reduced
Bore
2500
Full Bore
1/2
12
6
13
6
5
3/4
23
10
24
11
12
1
43
26
44
27
23
1-1/4
57
44
59
45
43
1-1/2
98
65
100
66
56
2
200
103
*
99
97
* 40mm = > 155
Cameron’s
NEWCO
Forged Steel
Globe Valves
Cv Values
Cameron’s
NEWCO
Forged Steel
Y-Pattern
Globe Valves
Cv Values
Cameron’s
NEWCO
Forged Steel
Swing Check
Valves Cv
Values
TC9308-4
NPS
150 - 800
Full Bore
150 - 800
Reduced Bore
1500
Full Bore
1500
Reduced Bore
1/2
3
2
3
2
3/4
6
4
6
3
1
12
6
12
6
1-1/4
15
10
--
--
1-1/2
21
18
20
16
2
38
22
24
20
NPS
800
1500
2500
1/2
5
5
3
3/4
11
11
6
1
14
15
12
1-1/4
--
--
--
1-1/2
37
35
27
2
68
68
36
NPS
150 - 800
Full Bore
150 - 800
Reduced Bore
1500
Full Bore
1500
Reduced Bore
1/2
5
4
--
--
3/4
12
6
--
--
1
17
13
--
--
1-1/4
26
18
--
--
1-1/2
54
28
--
--
2
101
55
--
--
56
Cameron’s
NEWCO
Forged Steel
Lift Check
Valves Cv
Values
NPS
150 - 800
Full Bore
150 - 800
Reduced Bore
1500
Full Bore
1500
Reduced Bore
1/2
3
1
3
2
3/4
5
3
6
3
1
11
6
11
5
1-1/4
--
--
--
--
1-1/2
18
15
19
11
2
32
18
22
19
Table applies to both piston and ball check valves.
Cameron’s
NEWCO
Forged Steel
Y-Pattern
Lift Check
Valves
Cv Values
NPS
800
1500
2500
1/2
4
4
3
3/4
11
11
6
1
13
14
12
1-1/4
--
--
--
1-1/2
36
34
27
2
67
67
36
Table applies to both piston and ball check valves.
TC9308-4
57
V. HOW TO ORDER ALL CAMERON’S NEWCO PRODUCTS
Figure Number
The figure number shown below identifies specific valve configuration details of
Cameron’s NEWCO valves such as valve type, pressure class, end connections, body/bonnet
and trim materials, and special features.
Please specify end connections, body materials and trims not listed below.
When placing an order, please refer to the respective product section of the catalog for
size availability. A detailed description must be included with any special orders.
TC9308-4
58
Pressure Class
Type
1= Gate, OS&Y
2= Globe/Globe Stop Check, OS&Y
3= Swing/Tilting Disc Check
4= Piston Check
5=Ball
6= Gate, NRS
7= Angle/Angle Stop Check, OS&Y
1=150
2=125
3=300
6=600
8=800
9=900
15=1500
16=1690
25=2500
26=2680
45=4500
End Connections
F=Flanged
J = RTJ
S= Socket Weld
T=Threaded
W= Butt Weld
X= Threaded x Socket Weld
Trim Material
Fig.18T-FS2 _ _
Suffix Letters
Body/Bonnet Material
A20= ASTM A351, CN7M =
Cast Alloy 20
CB= ASTM A216, WCB
=
Cast Carbon Steel
CC= ASTM A216, WCC
=
Cast Carbon Steel
C5= ASTM A217, C5
=
Cast Alloy Steel (5% Chrome, .5% Moly)
C6= ASTM A217, WC6
=
Cast Alloy Steel (1.25% Chrome, .5% Moly)
C9= ASTM A217, WC9
=
Cast Alloy Steel (2.25% Chrome, 1% Moly)
C12= ASTM A217, C12
=
Cast Alloy Steel (9% Chrome, 1% Moly)
12A= ASTM A217, C12A
=
Cast Alloy Steel (9% Chrome, 1% Moly, V)
CF3= ASTM A351, CF3
=
Cast Stainless Steel
C3M= ASTM A351, CF3M =
Cast 316L Stainless Steel
CF8= ASTM A351, CF8
=
Cast 304 Stainless Steel
C7L= ASTM A351, CG3M =
Cast 317L Stainless Steel
C8M= ASTM A351, CF8M =
Cast 316 Stainless Steel
C8C= ASTM A351, CF8C
=
Cast 347 Stainless Steel
CT= ASTM A351, CG8M =
Cast 317 Stainless Steel
DI= ASTM A395=
Cast Ductile Iron
FS= ASTM A105=
Forged Carbon Steel
F3M= ASTM A182, F316L =
Forged 316 Stainless Steel
F5= ASTM A182, F5
=
Forged Alloy Steel (5% Chrome, .5% Moly)
F7= ASTM A182, 317
=
Forged 317 Stainless Steel
F7L= ASTM A182, F317L =
Forged 317L Stainless Steel
F11= ASTM A182, F11
=
Forged Alloy Steel (1.25% Chrome, .5% Moly)
F22= ASTM A182, F22
=
Forged Alloy Steel (2.25% Chrome, 1% Moly)
F9= ASTM A182, F9
=
Forged Alloy Steel (9% Chrome, 1% Moly)
F91= ASTM A182, F91
=
Forged Alloy Steel (9% Chrome, 1% Moly, V)
F8= ASTM A182, F304
=
Forged 304 Stainless Steel
F8M= ASTM A182, F316
=
Forged 316 Stainless Steel
F8C= ASTM A182, F321
=
Forged 321 Stainless Steel
IB= ASTM A126, CLB
=
Cast Iron
LCC= ASTM A352, LCC
=
Cast Low Temperature Carbon Steel
LF2= ASTM A350, LF2
=
Forged Low Temperature Carbon Steel
MO= ASTM A414, M35
=
Cast NI Cu (Monel***)
SPL= Special (Customer to specify)
TC9308-4
59
API Trim =
1=CR13................................ 1, 4, 8A
2=CR13/HF**.............................8
3=CR13/FHF**...........................5
4=316........................................10
4/2=316/HF**..............................12
4/3=316/FHF**............................16
5= NI Cu (Monel***).................9
5/2=Monel/HF**.........................11
6= Alloy 20................................13
7=Bronze................................ N/A
A7= Aluminum Bronze............ N/A
8=Iron..................................... N/A
9= Special (Customer to Specify)
BP= By Pass
BS= Bellows Seal
CL= Chlorine Service
CR= Cryogenic Service
CW= Chain Wheel
EB= Extended Body
FP= Full Port
FS= Fire Safe
GI= Grease Injection
GO= Gear Operated
HB= Horizontal Ball Check
HP= Horizontal Piston Check
HO= Hydraulic Operator
INT= Integral Flanged
LD= Locking Device
LL= Locking Loop
LV= Live Load Packing
MO= Motor Operated
NC= NACE MR0103 Compliant
OL= Outside Weight & Lever
OX= Oxygen Service
PO= Pneumatic Operator
PS= Pressure Seal Bonnet
PT= PTFE Seats
QS=QuadroSphere
RP= Regular Port
SC= Stop Check
SL= Spring Loading
SPL= Special (Customer to specify)
TD= Tilting Disc Check
TF= Teflon* Insert
TM= Trunnion Mounted
VP= Vertical Ball Check
VL= Vertical Lift Check
VP= V-Port Disc
VT= Viton* Insert
WB= Welded Bonnet
Y= Y Pattern
*= Viton and Teflon are registered
trademarks of DuPont Company
**HF= Hardfaced - AWS 5.13 Class COCRA
***= Monel is a registered trademark of
International Nickel Company
NOTES:
TC9308-4
60
VI. INDUSTRY STANDARDS TYPICALLY USED IN VALVE MANUFACTURING
(For Reference Only)
British Standards Institute (BS)
ISO 9001: 2000
RWTUV approved Newmans for design, manufacture, sales, & service of industrial valves
under certificate registration number #08-1016
ISO 14001: 2004
The Newmans/Yancheng Manufacturing Team has passed the TUV-USA ISO 14001-2004
Certification Audit. All facilities inclusive of two (2) Foundries (Lost Wax and Sand Cast), Ball
Valve Factory, Final Processing Center and Warehouses 15 & 16.
BS 1414 (1975, R’ 91) - Gate, wedge & double disk valves: steel
BS 1868 (1975, R’ 91) - Check valves: steel
BS 1873 (1975, R’ 91) - Globe & check valves: steel
BS 2080 (1989) obsolete - Flanged & buttweld end steel valves
BS 5146 - (withdrawn) Replaced by BS 6755 p.1 steel valves testing (1986) & BS 6755 p.2
(1984) BS 5152 (1974, R’ 91) - Globe & check: cast iron
BS 5153 (1974, R’ 91) - Check: cast iron
BS 5159 (1974, R’ 91) - Ball: cast iron & carbon steel
BS 5160 (1974, R’ 91) - Globe & check: steel
BS 5163 (1986, R’ 91) - Gate, wedge & double disk: cast iron
BS 5351 (1986, R’ 91) - Ball: steel
BS 5352 (1986, R’ 91) - Globe & check: steel
BS 5418 - (withdrawn) Replaced by BS EN 19 (1992) marking: general purpose industrial
BS 5840 (1980, R’ 91) - Valve mating details for actuator operation
BS 6364 (1984, R’ 91) - Cryogenic
BS 6683 (1985, R’ 91) - Guide: installation & use of valves
BS 6755: Part 1 (1986, R’ 91) - Specification for production pressure testing requirements
BS 6755: Part 2 (1987) - Specification for fire type-testing requirements
BS EN 19 (1992) - Marking of general purpose industrial valves
American Petroleum Institute (API)
API RP 574 (1998) - Inspection practices for piping system components
API 589 (1998) - Fire test for evaluation of valve stem packing
API RP 591 (2003) - Process valve qualification procedure
API 594 (2004) - Check valves-flanged, lug, wafer & buttwelding
API 597 (1981) - Steel venturi gate valves, flanged, buttwelding ends
API 598 (2004) - Valve inspection & testing
API 599 (2002) - Metal plug valves - flanged, welding ends
API 601 (1988) - Metallic gaskets for raised-face pipe flanges & flanged connections (doublejacketed corrugated & spiral wound)
API 600 (2001) - Bolted bonnet steel gate valves for petroleum & natural as industries “ISO
adoption from ISO 10434”
API 602 (2005) - Steel gate, globe, & check valves for sizes DN100 and smaller for the
petroleum & natural gas industries
API 603 (2001) - Corrosion-resistant, bolted bonnet gate valves-flanged & buttweld ends
API 604 (1981) - Ductile iron gate valves, flanged ends
API 605 (1988) - Large-diameter carbon steel flanges (nominal pipe sizes 26” through 60”,
classes 75, 150, 300, 400, 600, & 900 (replaced by ANSI/ASME B16.47)
API 606 (1989) - Compact steel gate valves, extended body (included in API 602) fire test for
soft-seated quarter-turn valves “ISO adoption from ISO 10497-5 2004”
API 607 (2005) - Fire test for soft-seated quarter-turn valves “ISO adoption from ISO 10497-5
2004” API 608 (2002) - Metal ball valves, flanged, threaded, & welding ends
API 609 (2004) - Butterfly valves-double flanged, lug- & wafer-type
API RP 941 (2004) - Steel for hydrogen service at elevated temperatures & pressures in
petroleum refineries & petrochemical plants
API RP 520 (2000), Part 1 - Sizing, selection & installation of pressure relieving devices in
refineries
API RP 520 (2003), Part 2 - Sizing, selection & installation of pressure relieving devices in
refineries devices in refineries
API Spec 6A (2005) - Specification for wellhead & christmas tree equipment
API Spec 6D (2005) - Specifications for pipeline valves
API Spec 14D (1994) - Specifications for wellhead surface safety valves & underwater safety
valves for offshore service
API 5B (2004) - Threading, gauging thread inspection of coring, tubing, & line pipe threads
API 6AM (2003) - Material toughness
API 6FA (1999) - Fire test for valves
API 6FC (1999) - Fire test for valves with backseats
API 6FD (1995) - Specification for fire test for check valves
API Q1 (2003) - Specification for quality programs for the petroleum, petrochemical, &
natural gas
Canadian Standards Association
B51-97 - Boiler, pressure vessel, & pressure piping code Z245.15-96 - Steel valves
CAN3-z299.4-85 (reaffirmed 1997) - Quality assurance program - Category 4
CAN3-z299.3-85 (reaffirmed 1997) - Quality assurance program - Category 3
International Organization for Standardization
ISO 5211/1 (2001) - Industrial valves- part-turn actuator attachments
ISO 5211/2 (2001) - Part-turn valve actuator attachment-flange & coupling performance
characteristics
ISO 5211/3 (2001) - Part-turn valve actuator attachment-dimensions of driving components
ISO 5752 (1982) - Metal valves for use in flanged pipe systems face-to-face & center-to-face
dimensions
ISO 9000 (2005) - Quality management systems and fundamentals & vocabulary
ISO 10012-1 (1992) - Quality assurance requirements for measuring equipment
Manufacturers Standardization Society
ASNT-TC-1A (1996) - Recommended practice no. SNT-TC-1A 1996
SP-6 (2001) - Standard finishes for contact faces of pipe flanges & connecting-end flanges of
valves & fittings
SP-9 (r2005) - Spot facing for bronze, iron & steel flanges
SP-25 (1998) - Standard marking system for valves, fittings, flanges & unions
SP-42 (2004) - Class 150 corrosion resistant gate, globe, angle, & check valves with flanged
& buttweld ends
SP-44 (2001) - Steel pipeline flanges
SP-45 (2003) - Bypass & drain connections
SP-51 (2003) - Class 150/w corrosion resistant cast flanges & flanged fittings
SP-53 (2002) - Quality standard for steel castings & forgings for valves, flanges, & fittings &
other piping components: magnetic particle exam method
SP-54 (2002) - Quality standard for steel castings for valves, flanges, & fittings and other
piping components: radiographic examination method
SP-55 (2001) - Quality standard for steel castings for valves, flanges other piping
components-visual method for evaluation of surface irregularities
SP-60 (2004) - Connecting flange joint between tapping sleeves & tapping valves
SP-61 (2003) - Pressure testing of steel valves
SP-65 (2004) - High pressure chemical industry flanges & threaded stubs for use with lens
gaskets
SP-67 (2000A) - Butterfly valves
SP-69 (2003) - ANSI/MSS edition pipe hangers & supports, selection & application
SP-70 (1998) - Cast iron gate valves, flanged & threaded ends
SP-71 (1997) - Gray iron swing check valves, flanged & threaded ends
SP-72 (1999) - Ball valves with flanged or butt-welding ends for general service
SP-79 (2004) - Socket-welding reducer inserts
SP-81 (2001) - Stainless steel, bonnetless, flanged knife gate valves
SP-82 (1992) - Valve pressure testing methods
SP-84 (1990) - Valves - socket welding & threaded ends
SP-85 (2002) - Cast iron globe & angle valves, flanged & threaded ends
SP-86 (2002) - Guidelines for metric data in standards for valves, flanges, fittings & actuators
SP-88 (r2001) - Diaphragm valves
SP-91 (1992) - Guidelines for manual operation of valves
SP-92 (1999) - MSS valve user guide
SP-93 (r2004) - Quality standard for steel castings & forgings for valves, flanges & fittings &
other piping components- liquid penetrant exam method
SP-94 (r2004) - Quality standard for ferritic & martensitic steel castings for valves, flanges, &
fittings and others piping components - ultrasonic exam method
SP-96 (r2005) - Guidelines on terminology for valves & fittings
SP-98 (2001) - Protective coatings for the interior of valves, hydrants, & fittings
SP-99 (r2005) - Instrument valves
SP-101 (r2001) - Part-turn valve actuator attachment-flange and driving component
dimensions & performance characteristics
SP-102 (r2001) - Multi-turn valve actuator attachment: flange and driving component
dimensions & performance characteristics
SP-110 (1996) - Ball valves threaded, socket-welding, solder joint, grooved, & flared ends
SP-117 (2002) - Bellows seals for globe & gate valves
SP-118 (2002) - Compact steel globe and check valves-flanged, flangeless, threaded &
welding ends (chemical & petroleum refinery service)
SP-120 (2002) - Flexible graphite packing system for rising stem steel valves (design
requirements) SP-121 (R2002) - Qualification testing methods for stem packing for rising
stem steel valves
American Society for Testing and Materials (ASTM)
National Association of Corrosion Engineers (NACE)
American Society of Mechanical Engineers (ASME)
ASME Code (1997 addenda) - Boiler & pressure vessel code
ASME A13.1 (1996) - Scheme for the identification of piping systems ASME B1.1 (2003) Unified inch screw threads, UN, & UNR thread form ASME B1.5 (1997) - ACME screw threads
ASME B1.7M (1984) - Nomenclature, definitions, & letter symbols for screw threads
ASME B1.8 (1988) - Stub ACME screw threads
ASME B1.12 (1987) - Class 5 interference - fit thread
ASME B1.20.1 (1983) - Pipe threads, general purpose, inch
ASME B1.20.3 (1976) - Dry-seal pipe threads, inch
ANSI/ASME B16.1 (1998) - Cast iron pipe flanges & flanged fittings
ANSI/ASME B16.5 (2003) - Pipe flanges & flanged fittings: NPS 1/2” through 24” ASME B16.9
(2003) - Factory made wrought steel buttwelding fittings
ANSI/ASME B16.10 (2002) - Face-to-face & end-to-end dimensions of valves
ASME B16.11 (2001) - Forged fittings, socket welding & threaded
ASME B16.20 (1998) - Metallic gaskets for pipe flanges: ring joint spiral wound & jacketed
ASME B16.21 (2005) - Non-metallic flat gaskets for pipe flanges
ASME B16.25 (2003) - Buttwelding ends
ANSI/ASME B16.33 (2002) - Manually operated metallic gas valves for use in gas piping
systems up to 125 PSI (sizes NPS 1/2” through 2” )
ANSI/ASME B31.1 (2004) - Power piping
ANSI/ASME B31.3 (2004) - Process piping
ANSI/ASME B16.34 (2004) - Valves flanged, threaded & welding end
ANSI/ASME B16.36 (1996) - Orifice flanges
ANSI/ASME B16.38 (1985) - Large metallic valves for gas distribution (manually operated,
NPS 2-1/2” through 12”, 125 PSIG maximum)
ANSI/ASME B16.42 (1998) - Ductile iron pipe flanges & flanged fittings: classes 150 & 300
ANSI/ASME B16.47 (1996) - Large diameter steel flanges
ANSI B17.1 (1967, R’ 89) - Keys & keyseats
ANSI B18.2.2 (1987) - Square & hex nuts
ASME B31.4 (2002) - Pipeline transportation systems for liquid hydrocarbons & other
ammonia & alcohols
ANSI/ASME B31.8 (2003) - Gas transmission & distribution piping systems ANSI/ASME B36.10
(2004) - Welded & seamless wrought steel pipe ANSI/ASME B36.19 (2004) - Stainless steel
pipe
ANSI FCI-2 (1991) - Control valve seat leakage
American Society Non-destructive Test (ASNT)
MR0175 (2005) - Sulfide stress cracking resistant metallic materials for oil field equipment
MR0103 (2005) - Materials resistant to sulfide street cracking in corrosive petroleum refining
environments
TC9308-4
61
NOTES:
TC9308-4
62
NOTES:
TC9308-4
63
VALVES & MEASUREMENT
13127 Trinity Dr.
Stafford, Tx 77477
Toll Free 800.231.3505
Tel 281.302.4900
Fax 281.302.4801
Learn more about NEWCO valves at:
www.c-a-m.com/newco
newco@c-a-m.com
ENVIRONME
N
XCELLEN
LE
CE
TA
TH SAFETY
AL
A
HE
ND
CA
HSE Policy Statement
At Cameron, we are committed ethically, financially and personally to a working environment
where no one gets hurt, nothing gets harmed.
MERON
© 2013 Cameron • Produced by Technical Publications, Houston, TX, USA

Similar documents

NEWCO Pressure Seal Valves Technical Data Sheets

NEWCO Pressure Seal Valves Technical Data Sheets property or death or injury to any person resulting in whole or in part from repairs performed by anyone other than authorized Cameron personnel. Such unauthorized repairs shall also serve to termi...

More information

NEWCO Stainless Steel Valves Technical Data Sheets

NEWCO Stainless Steel Valves Technical Data Sheets this book should be done by an authorized Cameron service representative. Cameron will not be responsible for loss or expense resulting from any failure of equipment or any damage to any property o...

More information