Stamper #398 USER`S GUIDE

Troubleshooting:
Problem: Stamper does not work, intermittently or very slowly.
Action #1: Check all batteries for proper (+) & (-) battery polarity.
Stamper #398
Action #2: Replace all batteries with fresh new batteries. Never mix different
brands or old and new batteries.
Problem: Stamp is very light or faint on the paper.
Action #1: Make sure you have stamped 2 or 3 times making sure to have
enough ink on your Easy-Grip stamp.
Action #2: Try a new ink pad.
Action #2: Replace all batteries with fresh new batteries. Never mix different
brands or old and new batteries.
USER’S GUIDE
Action #3: Check to make sure nothing is blocking or restricting the
movement of the control switches.
Care of Unit:
Stamper can be wiped clean with any household multi-purpose cleaner and
disinfectant. We recommend Simple Green, which is a non toxic
biodegradable all-purpose cleaner.
Do not submerge the unit, as it will damage the contents and the electrical
components.
Do not use abrasive cleaners, as they will scratch the surface of the unit.
For Technical Support:
Call our Technical Service Department
Monday through Friday, 9 a.m. to 5 p.m. (EST)
1-800-TEC-TOYS or 1-800-832-8697
customer_support@enablingdevices.com
50 Broadway
Hawthorne, NY 10532
Tel. 914.747.3070 / Fax 914.747.3480
Toll Free 800.832.8697
www.enablingdevices.com
Learning through art!
Stampers is our latest addition to adapted arts and crafts. We’ve created a
mechanical stamp for those who love arts and crafts but have limited upper
body movement. Our unique control center has three gumball switches which
allow the user to drop the stamp onto the ink pad, move the stamp to your
paper, and then drop the stamp onto the paper. The control center also has
three switch input jacks for your own capability switches should you require
them. Kit includes: 14 dinosaur stamps and one ink pad (color will vary).
Control Center Size: 10"L x 5"W x 1 3/4"H; Stamper Size: 11"W x 21"L x
7"H. Requires 6C Batteries.
5. To change to another stamp you just have to simply pull the Velcro tab
away and place another stamp in the slot. There are also three 1/8" jacks
that control the same functions as the built in gumball switches for use
with any external capability switches.
6. You can purchase more ink pads and Easy-Grip stamps from Discount
School Supply. Their web site is www. DiscountSchoolSupply.com.
Make sure you get the Easy-Grip series of stamps which work with our
Stamper and the large ink pads.
Operation:
1. Stamper requires 6 C batteries (Not included). Use alkaline batteries only
(e.g. Duracell or Energizer brand). Do not use rechargeable batteries or
any other type of batteries because they supply lower voltage and the unit
will not perform properly. Never mix old and new batteries together or
different brands or types together.
2. The battery compartments are located under the base of the unit. Remove
the battery compartment covers by removing the Philips head screws
from the battery covers, slide the covers and lift off. Install new batteries,
being careful to observe proper (+) & (-) battery polarity. Replace
covers and screws.
3. To begin just line up the two red dots parallel to a large pad or piece of
paper (shown in Fig. 1) and put the large ink pad (included) far enough
out where the stamp can hit it. Now choose one of the 14 Dinosaur
stamps (Included) and put one of them into the slot of the stamp arm by
using the Velcro holding strap and finally adjust the head of the stamp so
it falls flat on the paper, using the stamp adjustment knob (shown in
Fig.1).
4. The stamp has a control center with three 2 ½" gumball switches a left
arrow, a right arrow and a stamp switch. This exceptional mechanical
stamp can turn 180 degrees by using the left and right control arrows. To
start stamping away just slightly lift the arm up and move over to the ink
pad then stamp 2 or 3 times making sure to have enough ink on your
Easy-Grip stamp, then move back over the pad or piece of paper and
stamp to your hearts delight..
Fig. 1
Important Notes:
When you are finished using the Stamper make sure to cover the stamp pad
with the cover or it will dry out. If this happens the pad can be re-activated
with water.
If Stamper is not going to be used for a long period of time, e.g. one month
or longer, we recommend removing the batteries from the unit during storage
to prevent battery drain or leakage, which can cause damage to the unit.
Rev 8/10/10