Product Catalog 2015

Transcription

CORRECT SOUND Custom
Product Catalog 2015
CORRECT SOUND Custom Product Catalog 2015
Correctsoundcustom.com
tube beta hybrid Mk-II preamp
$360
It’s a hybrid pedal in a compact box
size (187mm x 120mm x 38mm),
with two channels: tube and
"stone". The tube channel is based
on Sunn’s Model-T (1973), with
two 12ax7EH tubes. The "stone"
section has the preamp of the Sunn
Beta amplifier (bass or lead,
depending on the customer's
choice).
Unlike the first version of the pedal, the channels aren’t switched successively but in
parallel, as in our Beta Bass preamp. The new preamp has only one output and a
balanced XLR DI out, which has switches for pre/post master and ground lift. We also
offer true bypass.
Just like we did with model I of the Tube Beta Hybrid, we intend to produce two
variants of the Beta channel: BASS or LEAD, depending on the customer's choice. Each
channel has a classical set of regulators: gain, bass, mid, treble, level and master
volume.
Specification:













Channels quantity - 2 (tube, beta)
channel tube:
tube is based on the preamplifier of SUNN Model-T amp (1973)
passive EQ
separate output
channel beta:
beta is based on the preamplifier of SUNN beta amp (bass or lead)
Active EQ
Separate adjustment on each channel
Drive, bass, mid, treb, level, master volume
footswitch - t/b, t+b, bypass
XLR Balanced Out (optional)
U - 12VAC 1200mA (Power Supply not included)
MT tube preamp
$270
MT tube preamp is designed on the
base of the section of preamp of
guitar amplifier SUNN Model-T of
1973 on two ECC83 S (12ax7 EH)
tubes. In fact it is a channel tube of
our pedal “tube beta hybrid” in a
separate box, but there is one
difference. This preamp has got two
regulators of gain. Normal and
Bright ( as amplifier Sunn Model-T)
It gives possibility to change “brightness” of the signal smoothly.
Our preamp has TRUE BYPASS operated by relay. It works so that when power supply
disappears (ex: someone pulled out the cord by a foot by chance) the pedal switches
into mode bypass and sound doesn’t disappear.
Specification:











tube 2 X JJ ECC83 S (12AX7 EH)
gain N (normal)
gain Br. (bright)
bass
mid
treb
level
true bypass
U - 12 VAC 1000 mA (minimum)
power plug 5.5mm x 2,1mm
Dimension of the box: 144 mm x 120 mm x 58 mm ( on the level of knobs)
BETA Bass (Lead) preamp
$315
Bass preamp BETA is based on
preamplifier SUNN BETA.
Specification:








Channels quantity - 2 (A,B)
Active EQ
Separate adjustment on each channel
 Drive, bass, mid, treb, level
master volume
footswitch - BYPASS, A/B, A+B (parallel)
XLR DI out (optional)
true bypass
U - 18VAC (Power Supply not included)
MAD HATTER – fuzz & distortion Double effects pedal
$335
SUNN Channel is based on
preamplifier SUNN Concert
Lead.
MUFF Channel - GGG Tuned
version.
Specification:














effects Pedal
MUFF Chanel
sustain
tone
vol
SUNN Chanel
gain
bass, mid, treb
dist on/off
bright on/off
boost on/off
dist+boost
True Bypass
U - 18 VAC 350mA (Power Supply not included)
Bass preamp ECLIPSE Mk-II
$200
ECLIPSE is based on preamplifier
SUNN Concert Lead.
I put some changes into frequency
correction of the output cascade.
"boost" is ON constantly. Max
Output amplitude - 4,5V at
frequency 50Hz. This is enough to
swing any Power Amp.
Specifications:











effects Pedal
Tone: Bass, Mid, Treb
Dist
Gain
Level
dist on/off
bright on/off
True bypass
input impedans - 1M
output impedans - 100k
U-9V DC 350mA (Power Supply not included)
HARMONIC GENERATOR
$179
An HARMONIC GENERATOR is
an audio signal processing
technique used to enhance a
signal by dynamic equalization,
phase manipulation, harmonic
synthesis of (usually) high
frequency signals, and through
the addition of subtle harmonic
distortion.
Harmonic synthesis involves the creation of higher order harmonics from the
fundamental frequency signals present in the recording. HARMONIC GENERATOR is also
used to synthesize harmonics of low frequency signals to simulate deep bass in smaller
speakers.
Specification:









Harmonic control
gain
Q
freq
Mix
derect
harmonic
true bypass
U - 9V DC (Power Supply not included)
Parametric EQ - 3band parametric eqalizer
$179
Its tasck is fine tuning of the sound
timbre coloration.
Specification:
effects Pedal
 Freq:
 Bass - 30 ... 400 Hz
 Lo Mid - 400 ... 1500 Hz
 Hi Mid - 1,5 ... 5 kHz
 Q 0,25 - 2,5
 Level of regulation
 Master Volume
 Input impedans - 1M
 U - 9VDC (Power Supply not
included)

Some examples of using
Add some boost in range 3 kHz with wide
Q
To reach the sound
Suppose you are fully sutisfied with the sound of your musical instrument but you
would like to have it brighter to sound in mix but not to bulge in volume
To correct
Acoustics of the room makes the sound of your instrument chanting.
This effect can be minimize by cutting low
(200 Hz - 400 Hz) or low mid (450 HZ 600 Hz) with middle Q.
If sound of your guitar is disappearing among other instruments
Add high mid instead of adding volume to
prevent hammer in other instruments
Speaker simulation
If you have to play in a line for some reason you may easy to set emulation Cab+mic
using the parametric. Just turn the regulation correct to receive sound of any
speaker simulators as well as to modulate any pair cab+mic.
Cut a little bit (1/3) 250 Hz at mid close to
low. rise a little (apr on 1/4) 3 HZ at mid Q
Preamp
Use as "warmer"
Plug Parametric EQ first in a chain of
effects, set timbre and you get nice
booster.
To wide your staff possibility
Personal regulator of timbre that is always with you
Plug the device into loop effects of amp
and ... well, you get it.
Splitter-blender
$100
Our new pedal contains two different
and independent devices in one box.
Two channel splitter is to the right.
Two channel blender is to the left. In
and out of this pedal do not depend
on each other. In is for splitter and
Out is for blender.
Splitter divides the input signal into
two
perfectly
independent
and
absolutely identical signals. There are
no any regulators. You can send the
signals, for example, to two amps or
to two different effects chains and so
on. Wherein the blender can be out of
use.
The blender has two inputs A and B
and can be on/off by the right switch
A+B. When it is on the LED indicator beside the switch blend is on. When blender is on,
signals from both inputs are blended and lead the out. You can regulate correlation of
signals with the help of knob blend. Switch phase changes phase of the signal from B
channel into opposite. Due to this you can sum or recoup the signals.
There is one more difference between channel A and channel B. If there are no
connection In channel B then a signal from input of the splitter in is lead to the channel
B with the help of inner splint. This allows to blend direct signal with processed signal.
The inner connection is off when the plug is on to the channel B.
If the blender is off the signal from one of the channel leads directly to out (true
bypass). The left footswitch A/B switches either A or B signal leads to the out. The
correspondent indicators is on.
9 V DC outside stabilizing power supply is necessary for functioning of this pedal. The
power plug has standard connection for effect pedals – minus in the center.
ATTENTION
Some our preamps work only with alternating voltage


Tube beta hybrid preamp, MT tube preamp – 12 volt
MAD HATTER, beta preamp - 18 volt.
On the label of your power supply it should read:
For U.S. and Canada
Input – 120 VAC 60Hz
output ~12VAC 1000mA for tube preamps
output ~18VAC 500mA for other
For Russia, Europe Australia …
Input – 230 VAC 50Hz
output ~12VAC 1000mA for tube preamps
output ~18VAC 500mA for other
plug 5,5mm x 2,1mm center
If you use AC/DC power supply, the pream won't work.
NO DC !!! No +/- NO polarity

Product Catalog 2015

Transcription

Similar documents

4-Series • 44-02 • 55-Series • 55-02 55-01-NTMB • Jerry

Xotic Bass Brochure Downlaod

Keeley Looper Manual

Read More. - Locomotive Audio

Tech 21 VT Bass DI

BTA8100

Luxman C-700u/M-700u

PDF - The Kandinsky Effect

BTA6100