Serena® Roller Shade Installation and Setup Guide

Roller Shade
English
Battery-Powered Window Shade with RF Wireless Remote Control • Installation and Setup Guide—Please Read Before Installing and Operating
Thank You!
Congratulations on your purchase of a Serena® remote-controlled shade by
Lutron®. We trust you will be delighted with the comfort and convenience
these shades will bring to your home.
Be sure to register your shade(s) and share your experience with our products at
www.lutron.com/serenaregistration.
As the world leader in light and shade control, we thank you for selecting
Serena shades and look forward to working with you again. If you have
any questions, please email us at serenashades@lutron.com or call our
24/7 customer support hotline at 888.445.8063.
1 Mounting the Back Cover:
! CAUTION:
RISK OF FALLING OBJECTS. Securely install
the shade system per the mounting instructions. Failure to do
so could result in minor or moderate injury.
1.1 Hold the Back Cover A up to the mounting surface.
Approximate its final position centered on the window, and use
a pencil to mark mounting screw locations on the Back Cover.
To ensure the Back Cover is properly mounted, we recommend:
a.Plan to install a mounting screw 2 - 5 in (51 - 127 mm) from each end
of the Back Cover.
Sincerely,
The Lutron Serena Team
2 - 5 in (51 - 127 mm)
SHADES UP TO
48 in (1219 mm)
Included in the box:
2 - 5 in (51 - 127 mm)
b.For shades wider than 48 in (1219
install two additional
2 - 5mm),
in (51plan
- 127tomm)
SHADES UP TO
mounting
48 in (1219
mm) screws, equally spaced across the Back Cover. DO NOT
SHADES
install
a screw at the center of the Back Cover.
WIDER
THAN
48 in (1219 mm)
A
1.2 According to the mounting option chosen on the original order, fasten the Back Cover
provided B or other appropriate fasteners.
B
Back Cover
Mounting Screws
(qty. varies with
shade size)
Outside Mount
above Trim
A
B
B
NOTE:
Ensure the
Back Cover
is centered in
the window
opening.
There must be
equal space
between each
end and the
side trim.
A
B
Equal space
both sides
A
B
Spacers D
between the Back
Cover and the
mounting surface
(included only when
outside mount above
trim is specified)**
**NOTE: Depending on the size
of your shade and the depth of
your trim, or the roll direction of
your shade, you may be able to
mount the shade directly to the
wall above the trim without using
the spacers.
MOUNTING
OPTION:
Outside
Mount
on Trim
d.Verify that the mounted Back Cover is level, centered on, and parallel
to, the window opening.
1.2 Pre-drill the Back Cover
(3.2 mm) drill bit.
Inside
Mount
EQUALLY SPACED
c.Locate the mounting screws so that they drive into studs or solid
trim. For surfaces other than solid wood, use appropriate expansion
anchors, toggle bolts, or other fasteners (not included).
Serena® Roller Shade Assembly
(standard system or with optional fascia*)
MOUNTING
OPTION:
to the mounting surface using the mounting screws
Equal depth
both sides
EQUALLY SPACED
C
MOUNTING
OPTION:
2 - 5 in (51 - 127 mm)
SHADES
WIDER THAN
48 in (1219 mm)
A,
at the pencil marks, using a 1/8 in
B
A
Align the
top of the
Back Cover
with the top
edge of
the trim
B
In this arrangement, the top
of the Back Cover must be a
minimum of 51/4 in (133 mm)
above the top of the trim.
Spacers (included only
when outside mount
above trim is specified)
E
Center Support (included
only with shades wider
than 48 in / 1219 mm)
*NOTE: If your shade was ordered with Optional Fascia, the fascia will be
attached at the factory and wrapped with the shade during packaging.
Leave the wrapping in place during installation for added stability. After the
shade is hung securely, use scissors to cut the wrap material from below
the shade, then remove it by pulling it out through the top of the shade.
2 Installing the Center Support:
NOTE: The Center Support is included only with shades
wider than 48 in (1219 mm). If the width of your shade is
48 in (1219 mm) or less, skip this step.
3.1 Rest the inner part of each end bracket
(shaded below), on the lower tab of the
mounted Back Cover A .
A
Other items you’ll need:
A
WIDE SHADES WITH CENTER SUPPORT: The
Center Support is positioned to cradle the shade’s
battery holder. On wide shades, the center of the
battery holder mayCLICK!
sag during installation step 3.1,
requiring you to lift it up and into the cradle as you
proceed to step 3.2.
BATTERY HOLDER
SUPPORT
PROPERLY CRADLED IN CENTER
CLICK!
CRADLE
E
D-Cell Alkaline Batteries
(6 or 8 depending on shade size)
Level
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
CLICK!
CENTER SUPPORT
CLICK!
NOTE: It is recommended that shades wider than
48 in (1219 mm) are installed by 2 persons.
Power Drill
3.2 Push the top of the shade into the
Back Cover, locking the brackets
with an audible “click” at each end.
C
Pencil
#2 Phillips
Driver Bit
Reverse
roll
CLICK!
CLICK!
1/8 in (3.2 mm)
Drill Bit
Regular
roll
3 Hanging the shade:
2.1 Position the Center Support E midway across the mounted
Back Cover as shown and lock it into the Back Cover with
an audible “click.”
Tape Measure
Wall
Trim
NOTE: The Back Cover features grooves to help stabilize the point of
your drill bit.
D
5.25 in
(133 mm)
min.
TO REMOVE THE SHADE: With the shade
firmly supported, press down on the release
tab at the top of each end bracket.
= Optional Fascia
12/2013
P/N 045404 Rev. B
Lutron, O, Serena and Pico are registered trademarks of Lutron Electronics Co., Inc.
Serena® Roller Shade Installation and Setup Guide
Page 2
4 Installing the batteries:
4.1 Open the battery holder at the top of the shade.
4.2 Insert new D-cell alkaline batteries.
With Optional Fascia: pull out, then down on the fascia.
Without Optional Fascia: rotate the top section forward.
5 Assigning a remote control:
4.3 Return the battery holder to the closed position.
With Optional Fascia: push the fascia up, then in.
A diagram on the battery holder shows quantity and orientation.
When all batteries are inserted properly, the shade button LED
(see section 5 ) will flash red/green as the shade powers up.
6 Adjusting shade limits (OPTIONAL):
Pico® wireless control
Restoring factory default settings:
The shade’s upper and lower limits are pre-programmed based on the window dimensions and mounting option.
If adjustment is needed, follow these steps:
Compatible remote controls (sold separately)
Serena® 4-Group RF remote control
Open
Open
Raise
Close
Lower
Close
a.Tap the Shade
Button.
b.The Shade
Button
illuminates.
c.Press and hold the Open
and Raise Buttons.
d.The Shade Button flashes,
then stays on.
Favorite
Favorite
Lower
Shade Button
with LED
Shade
Groups
Close
A Serena ® roller shade
NOTE: Restoring a Serena® roller shade to its factory
default settings will remove all control assignments and
favorite programming. Upper and lower limits are retained.
•Tap the Shade button 3 times, (triple-tap), then press
and hold. The Shade Button LED will illuminate and flash
GREEN rapidly while you continue to hold.
Open
Raise
Without Optional Fascia: rotate the top section
back to the closed position
Shade
B Pico ® wireless control*
All
1
2
3
4
•Release the button and immediately triple-tap it again;
(do not hold). The Shade Button LED will flash GREEN
rapidly, then flash RED/GREEN three times, and turn
off. When the LED stops flashing, the shade has been
restored to factory default settings.
•Tap the Open or Close button 3 times, (triple-tap), then
press and hold. The LED next to the Open button will
illuminate and stay on while you continue to hold.
All Shade
Groups
e.Use the Raise and Lower
Buttons to position the
shade at the preferred
upper or lower limit.
f.
SET UPPER LIMIT
With the shade at the
preferred upper limit, press
and hold the Open Button.
OR
SET LOWER LIMIT
With the shade at the
preferred lower limit, press
and hold the Close Button.
g.The Shade
Button flashes.
Limit set is
complete.
•Release the button and immediately triple-tap it again;
(do not hold). The LED will flash quickly. When the LED
stops flashing, the control has been restored to factory
default settings.
C Serena ® 4-Group RF remote control*
5.1 Assign a Pico ® wireless control
•Tap the All Shade Groups button.
7 Setting a favorite level (OPTIONAL):
a. Tap the Shade
Button.
b. The Shade
Button
illuminates.
c.Press and
hold the Close
button.
d.The Shade
Button flashes.
Assignment is
complete.
e.Repeat for
additional
shade/control
assignments.
5.2 Assign a Serena ® 4-Group RF remote control
The favorite level is factory programmed to the midpoint between the factory programmed upper and lower
shade limits.
NOTE: When setting
differing favorite levels
among multiple shades
assigned to the same
control, disconnect power
to the shades you do not
want affected by removing
b.Press and hold the
c.The Shade Button
a.Use the Raise and Lower
one battery from each.
Favorite Button.
flashes. Favorite
Buttons to position the shade
level is set.
at the desired favorite level.
•Tap the Open or Close button 3 times, (triple-tap), then
press and hold. The All Shade Groups button LED will
illuminate and stay on for approximately 3 to 5 seconds
while you continue to hold.
•Keep the button pressed until the All Shade Groups
button LED turns off.
•Release the button and immediately triple-tap it again; (do
not hold). The LED’s of Shade Group buttons 1 - 4, and
the All Shade Groups button will illuminate and stay on
for approximately 3 to 5 seconds. When all LED’s turn off,
the control has been restored to factory default settings.
*NOTE: Restoring factory default settings will remove all
shade assignments and favorite programming.
Open
FCC Information
Models: SYC-J-EDU-R2, QSFC-J-EDU-R2
Close
Shade
All
1
2
3
4
a. Tap the Shade
Button.
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
b. The Shade
Button
illuminates.
c.Choose a
Shade Group
button. Press
and hold.
12/2013
P/N 045404 Rev. B
d.The Shade
Button flashes.
Assignment is
complete.
e.Repeat for
additional
shade/control
assignments.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio and television reception, which can be determined by turning
the equipment off and on. The user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by Lutron Electronics Co. could void the
user’s authority to operate this equipment.
For complete warranty information, please see: www.serenashades.com/warranty
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003.
IC Information
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
tot he following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation of the device.
Worldwide Headquarters | USA
Lutron Electronics Co., Inc. 7200 Suter Road, Coopersburg, PA 18036-1299 USA
TEL: 1.610.282.3800 • FAX: 1.610.282.3090
Technical Support: 1.800.523.9466 • Toll Free: 1.888.LUTRON1
Email: shadinginfo@lutron.com • Online: www.lutron.com/shadingsolutions
Europe Headquarters | United Kingdom
Lutron EA Ltd. 6 Sovereign Close, London, E1W3JF, UK
TEL: +44.(0)20.7702.0657 • FAX: +44.(0)20.7480.6899
Technical Support: +44.(0)20.7680.4481
FREEPHONE: 0800.282.107
Lutron, O, Serena and Pico are registered trademarks of Lutron Electronics Co., Inc.