Aerators - Flow-Rite

091911
Aerators
Aerators
21
Aerators
Aerators
PowerStream Aerator
The PowerStream Aerator features a venturi air intake at the top of the
discharge head to maximize the oxygen entering the livewell water. The
longer mixing tube directs this mixture directly to the depths of the livewell
and is then discharged horizontally well below the water line through the
discharge nozzle at the bottom of the tube. The discharge nozzle is adjustable
and can be rotated 360º.
Since the thru-hull fitting and venturi intake are mounted above the livewell
water line, it can be used with either a transom mounted fill pump or a
livewell mounted recirculation pump without worry of water being siphoned
out when the pump is off. It includes a special elbow thru-hull fitting.
Venturi Air-Intake
Allows air to be brought
in and mixed with water
Locking Nut
Leave aproximately 3/16”
of threads on thru-hull
exposed for the locking
nut which is designed to
allow the mixing tube
assembly to swivel if
bumped while preventing detachment
Mixing Tube
Water and air are mixed
together before exiting
the discharge port
Discharge Port
Can be rotated in any
direction to circulate the
water in the livewell
TOP VIEW
22
360º
Typically mounted near
a corner of the livewell,
some of the possible
mounting locations are
shown here. Rotate the
discharge to promote
circulation.
Flow-Rite Controls 960 74th St., Byron Center, MI 49315 www.flow-rite.com
Aerators
4"
2"
Aerators
2"
7/8"
(see chart for available lengths)
1/2"
Air
Wa
ter
Length
PowerStream Aerator w/Thru-hull, Standard
PowerStream Aerator w/Thru-hull, Long
PowerStream Aerator w/Thru-hull, Extra Long
8-7/8”
14-7/8”
21-3/4”
091911
Qwik-Lok
Part #
MH-PSA-209
MH-PSA-215
MH-PSA-222
Barbed
Part #
MH-PSA-109
MH-PSA-115
MH-PSA-122
23
Aerators
Aerators
PowerStream Nozzle
The PowerStream Nozzle features a venturi air intake in the top of the nozzle that draws additional oxygen into the water
as it enters the livewell. Unlike typical overhead spray heads, oxygen rich water immediately penetrates the deepest
livewells with ease and can be rotated left or right for a circular current of the livewell water. A special elbow thru-hull
fitting is included.
Locking Nut
Leave aproximately 3/16” of threads
on thru-hull exposed for locking nut
Venturi Air-Intake
Allows air to be brought in and
mixed with water
Discharge Nozzle
Can be rotated to provide circulation in the livewell
TOP VIEW
•Typically mounted near a corner
of the livewell, some of the
possible mounting locations are
shown here. Rotate the discharge
to promote circulation.
Nozzle may be rotated left or right to promote
livewell water circulation
24
Flow-Rite Controls 960 74th St., Byron Center, MI 49315 www.flow-rite.com
Aerators
Aerators
4"
2"
7/8"
Wate
r
1/2"
Air
2"
Qwik-Lok
Part #
MH-PSN-200
PowerStream Nozzle w/Thru-hull
091911
Barbed
Part #
MH-PSN-100
25
Aerators
Aerators
Pump-Out Aerator
A pump-out feature provides a convenient means of filling a tournament livewell weigh-in bag and also enables a livewell to
be pumped out while the boat is still in the water or when moored at a dock overnight.
The Flow-Rite Pump-Out Aerator is the easiest, most efficient, and least expensive means of adding a pump-out system
to any livewell system. It eliminates the need for additional diverting valves, cables, actuators, electrical connections and
most of the plumbing required by other systems. Simply install the Pump-Out Aerator in place of the standard spray head
used with any recirculation pump or with any of our V3 or V4 control valves that include a “RECIRC” mode. It has two hose
connections, one intake from the pump and one outlet for the discharge hose that will connect to the new discharge thruhull fitting.
The two position head is pushed in to bring water into the livewell where it is recirculated and aerated by the air intake and
venturi built into the head. Pull the head to the out or “pump-out” position to divert the water from the livewell to the
discharge thru-hull. The head can also be rotated left or right to promote a desirable circular current within the livewell.
The venturi will ensure that the maximum amount of oxygen allowed by ambient conditions will be provided to all levels and
areas of the livewell.
Locking Nut
Leave aproximately 3/16” of
threads on thru-hull exposed
for locking nut
Venturi Air-Intake
Aerator Head
Discharge Nozzle
Simply pull to pump-out
and push to aerate
Can be rotated to provide
circulation in the livewell
26
Pump-out Port
Allows air to be brought in
and mixed with water
Connects to pump-out
thru-hull
Intake Port
Connects to recirc pump
Flow-Rite Controls 960 74th St., Byron Center, MI 49315 www.flow-rite.com
Aerators
Pump-Out Aerator with livewell mounted recirculation pump
Recirc
Pump-Out
Aerators
Pump-Out Aerator with a V3 or V4 valve system in RECIRC mode
Recirc
Pump-Out
Note: Place control valve in the “RECIRC” position when using pump-out
2 7/8"
2"
5 3/4"
1"
1/2"
2 5/8"
A special thru-hull fitting is available for
use with the Pump-out Aerator. MA-020-B
(barbed) and MA-020-QLB (Qwik-Lok)
Pump-Out Aerator
Pump-Out Aerator Retail Pack wThru-hull, decal, & instructions
Discharge Straight Thru-hull, black w/Decal
Discharge Elbow Thru-hull, black (no decal)
091911
Qwik-Lok
Part #
MA-024-QLR
N/A
MA-020-QLB
MA-027-QLB
Barbed
Part #
MA-024-R
MP-1000
MA-020-B
MA-027-B
27
Aerators
Power-Jet Aerator
Aerators
The Power-Jet aerator is designed to be mounted well below
the surface of the livewell for direct introduction of fresh
oxygenated water. It can be used with systems 2, 3, or 4, or a
livewell mounted aerator pump only. (It is not for use with a
transom mounted pump.) Includes a special air intake fitting
with gasket and nut.
Remote Venturi Intake
Venturi air intake has many mounting
options and can be mounted anywhere
above water level. Shown here with
optional domed decal.
Air Intake Tubing
Easily routed and may be cut to lenth to
suit specific needs.
TOP VIEW
Typically mounted near a corner of
the livewell to promote circulation,
some of the possible mounting
locations are shown here.
28
Discharge Nozzle
Should be mounted near a corner to
promote livewell water circulation.
Flow-Rite Controls 960 74th St., Byron Center, MI 49315 www.flow-rite.com
Aerators
Air Intake Mounting Options
Mounting air intake without decal
Drill a 3/8" hole in a location well above the highest water line of the livewell in an area
that allows the routing of the air intake tubing. Insert air intake with rubber gasket. Use a
3/16" allen wrench in air intake head while tightening nut on back side of tank wall. Push
air hose onto air intake.
Pick a location well above the highest water line of the livewell in an area that allows the
routing of the air intake tubing. This is usually an area along the vertical rise of the
gunnel. Drill a 3/8" hole, deburr and clean surrounding area with alcohol. Mount the air
intake fitting to a 3/16" allen wrench. Carefully remove decal from protective backing and
insert intake fitting through center hole.
Aerators
Mounting air intake with decal
Mounting air intake when there is no access to back of mounting surface
3"
e
ta
k
Pow
1 3/8"
1/4"
2 7/8"
DCL-PJ1-G
-R
OW I
TE
e
Pow
1/2"
1 3/4"
3/4"
ta
k
FL
DCL-PJ1-W
2"
er
-Jet Air In
er
-Jet Air In
DCL-PJ2-W
5/8"
-R
OW I
TE
FL
Pick a location well above the highest water line of the livewell in an area that allows the
routing of the air intake tubing. This is usually an area along the vertical rise of the
gunnel. Drill a 3/4" hole, deburr and clean surrounding area with alcohol. Route tubing
from aerator leaving a few inches of excess tubing out hole. Mount the air intake fitting to
a 3/16" allen wrench. Carefully remove decal from protective backing and insert intake
fitting through center hole. Install mounting nut. Install air intake tubing to air intake
fitting. Orient the text properly and push assembly into 3/4" mounting hole. When decal
is firmly bonded to surface, remove allen wrench.
DCL-PJ2-G
PJA w/Air Intake Assy, (No decal, no air tubing)
PJA w/Air Intake Assy & 20" Air tubing, (no decal)
PJA w/Air Intake Assy w/60" Air tubing & Decal w/ White lettering
PJA w/Air Intake Assy w/60" Air tubing & Decal w/ Gold lettering
Air Tubing, 3/16" I.D., Sold by foot
Domed Decal, Single White lettering
Domed Decal, Single Gold lettering
Domed Decal, Double White lettering
Domed Decal, Double Gold lettering
091911
Qwik-Lok
Barbed
Part #
Part #
MH-PJA-200
MH-PJA-100
MH-PJA-220
MH-PJA-120
MA-1043
MA-1044
MA-1045
MA-1046
MD-055
LBL-PJ1-W
LBL-PJ1-G
LBL-PJ2-W
LBL-PJ2-G
29
Aerators
Spray Head Aerator
Spray head, Straight
Aerators
•Spray head may be rotated
to promote livewell water
circulation
3 7/8"
2"
1/2"
1 3/4"
5/8"
Qwik-Lok
Part #
MA-071-QLW
Sprayhead, Straight
Barbed
Part #
MA-071-W
Spray head, Elbow
•Spray head may be rotated
to promote livewell water
circulation
2 7/8"
2"
3 1/4"
1"
5/8"
Sprayhead, Elbow
30
Qwik-Lok
Part #
MA-077-QLW
Barbed
Part #
MA-077-W
Flow-Rite Controls 960 74th St., Byron Center, MI 49315 www.flow-rite.com
Aerators
Spray head with Shut-off
1 5/8"
2 3/8"
4 1/4"
Aerators
CL
N
OS
E - OPE
•Fully adjustable from off to
fully open
•Ideal for use with single fill
pump routed to two or more
bait or livewells
•Not for use with V2 or V3
automatic system
Sprayhead with Shut-off
Qwik-Lok
Part #
MA-051-QLW
091911
Barbed
Part #
MA-051-W
31